SPL REPAIRS TO BLDG NO. NP-32 AT NORTHERN COMD VEH DEPOT AND BLDG NO. NP-60 SINGLE JCO LIVING ACCN AND PROVN OF INSTALLATION OF LIGHTENING CONDUCTOR AT BLDG NO. NP-06 UNDER GE (NORTH) UDHAMPUR.

Amount

Taking down chowkats or frames (without taking off shutters from frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from frame), area exc 1.50 Sqm but not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down shutters of any description, area exc 1.0 Sqm but not exc 2.0 Sqm each, complete all as specified and directed.

S&F pressed steel frames (factory made), made out of 1.25mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate etc complete, size (section) of frame 125x60mm including bottom of each chowkat, complete all as specified and directed.

S&F pressed steel frames (factory made), made out of 1.25mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate etc complete, size (section) of frame 105x60mm including bottom of each chowkat, complete all as specified and directed.

S&F factory made 2nd class hardwood, rail and sylpe 35mm thick plain panelled shutters, solid core construction and 9mm thick BWP commercial and 12mm thick veneered partical board with block board core and plywood face panels, commercial type on both sides and both face is covered with decorative face sanmika (pattern and design as directed by Engr-in-Charge) with lipping/frame to match and polished on sides of shutters, complete all as specified and directed.

S&F 32/35mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton, factory made shutters (three panel) open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm, made out of 5mm plain colour PVC sheet reinforced with MS Square tube in opening and fixed at site, complete all as specified and directed.

S&F factory made solid panel PVC door shutter, 30mm thick style, consisting of frame made out of MS tube for top & bottom rail, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm wide struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, bottom rail & lock rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement as per specification and drawing shown in SSR Pt -ll (Rate), complete all as specified and directed.

S&F 28mm thick factory made soild PVC profiled panel door shutter with integral skin as frame and 3mm thick high pressure compact laminate on both side of approved colour as infill with 'C type Gl or 40x20x19mm of MS pipe as stiffner and supplying & fixing in frame at site as per specifications, drawing and directed by EIC.

S&F aluminium alloy hasp and staple, 100mm long and width not less then 40mm, complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as filling in back of pressed steel frame, hold fasts and similars articles, complete all as specified and directed.

M&L for 18-25mm thick machine cut kota stone slabs as in flooring, laid/ fixed over and including 15mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and rounding of edges, complete all as specified and directed.

M&L for 18-25mm thick machine cut kota stone slabs as in skirtings/ dados, fixed over and including 15mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate 'Z' sections and other sections of approved make, conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, CP brass / stainless steel screws, complete as per architectural drawings and the direction of Engineer-in-Charge. Note :- Rates shall be deemed to include for necessary roller for sliding and locking for sliding window / ventillator.

S&F powder coated anodised aluminium window and ventilator shutters, fixed/ sliding type, openable/ side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.), complete all as specified and directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/ pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete as per site requirement and direction of Engr-in-Charge.

S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregrates) as in foors, plinth protection, surface channel, path etc, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F 100mm long mild steel butt hinges, medium weight, cold rolled, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 150mm long aluminium handles, cast type, anodised, complete all as specified and directed.

S&F floor door stoper of 140mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed.

S&F 5mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beading in glass panes of any size, complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in squares, in panes of any size, complete all as specified and directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares, in panes of any size, complete all as specified and directed.

S&F in replacement wash hand basin, vitreous china, flat back or angle back type of size 580x450mm including 32mm dia CP waste coupling, 32mm dia PVC waste pipe and angle bracket of size 30x30x4mm thick 450mm long and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F in replacement vitreous china urinal, half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm brass screws, pointing around urinal back in cement and CP urinal spreader of 15mm dia, complete all as specified and directed.

S&F in replacement wash down water closet (pedestal pattern) complete with Pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. including PVC seat and cover, complete all as specified and directed.

S&F in replacement viterous china squatting pan, Orissa pattern, of size 580x440mm, white with integral foot rest (excluding flushing cistern and flush pipe) with 'P' or 'S' trap including removing of old CI pipe and demolition of PCC upto 450mm thick, complete all as specified and directed.

S&F in replacement PVC high/ low level flushing cistern of 10 ltrs capacity, fixed including syphonic action type, ball valve, float and handle including brackets etc, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks etc. including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

Demolition and breaking up 100mm internal dia (and less) drain pipes (SGSW, AC or reinforced concrete pipes), set in cement mortar, complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes of 150mm bore, jointed in cement mortar and taking out from trenches or taking down from walls, complete all as specified and directed.

Dismantling of 75/100mm bore cast iron drain pipes, jointed in cement mortar and taking out of trenches (if required), complete all as specified and directed.

S&F 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors, complete all specified and directed.

S&F 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floor, complete all as specified and as directed.

S&F 75mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, fixed in walls with and including MS clamps of suitable size, complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with MS clamps of suitable size or laid in floor/ trenches, complete all as specified and directed.

S&F in replacement 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints including bends, tee, Y junctio, fixed to walls with MS clamps of suitable size or laid in floor/ trenches, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, suitable for 75/110 bore pipe, complete all as specified and directed.

S&F in replacement 100mm bore sand cast iron cast bends/ reducer/ Tee (any radius) with access door, diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F in replacement 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed.

S&F 75/100mm bore CI vent cowl including taking down old CI vent cowl of any type, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed.

S&F 15mm bore steel water tubing, medium grade, galvanised with all fittings and fixtures, fixed to wall or ceiling or laid in floors, complete all as specified and directed.

S&F 20mm bore steel water tubing, medium grade, galvanised with all fittings and fixtures, fixed to wall or ceiling or laid in floors, complete all as specified and directed.

S&F in replacement gun metal, globe or gate valve with iron wheel head, screwed both ends for 20mm bore iron pipe, complete all as specified and directed.

S&F in replacement PVC connection of 15mm dia with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in replacement 100mm dia chrominium plated grating doom (min. weight 25 gms), complete all as specified and directed.

S&F brass chromium plated angle valve / stop valve, high pressure, screwed down, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F 300mm size, ordinary rat tail rod pattern springs including roller and roller plate, fixed to wooden or steel frames with welding etc, complete all as specified and directed.

S&F in replacement brass chromium plated shower rose of size 125mm with swivel joint, fixing to GI pipe of 15mm bore, complete all as specified and directed.

S&F in replacement bib tap, chroimum plated with crutch or butterfly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule including elbow/ socket etc as required at site, complete all as specified and directed.

Dismantling water tank and removing to store, exc 250 litres but not exc 500 litres capacity with all necessary fittings, complete all as specified and directed.

S&F 3 layer rotational moulded polyethylene water storage tank, white in colour, 1000 ltrs capacity (cylindrical vertical with closed top) with 20mm dia ball valve, epoxy coated aluminum rod, plastic ball etc, hoisted and fixed in position including tank nipple inlet and outlet and conneting pipes, complete all as specified and directed.

S&F PVC floor trap of 75mm bore, plain wih grating including jointing with solvent cement, complete all as specified and directed.

S&F cast iron floor trap of 75mm bore, plane wih grating including jointing with solvent cement, complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone masonry or cement concrete walls including raking out joints, hacking for key, scrubbing down with water including remaval of derbis, complete all as specified and directed.

M&L for 15mm thick rendering into two layers consisting 10mm thick in CM 1:4 followed by 5mm thick in CM 1:4 with using WPC on fair faces of brick work or concrete surface including finishing the surface even and fair without using extra cement, complete all as specified and directed. Note :- WPC shall be measured and paid separately under respective item of this BOQ.

M&L for 10mm thick rendering on other than fair faces of brick work or concrete surface in CM 1:6 including finishing the surface even and smooth without extra cement, complete all as specified and directed.

M&L for 5mm thick rendering on ceiling surfaces of concrete or brick work in CM 1:3, complete all as specified and directed.

Complete removal of existing treatment on walls and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty, complete all as specified and directed.

Complete removal of existing treatment on walls and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint, white or tinted, over and including a coat of chalk whitening primer and 1-2mm thick wall care putty, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer over and 1-2mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 Gm/litre and UV resistance as per IS:15489-2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust etc. and brushing neat cement slurry with 3.0 Kg of cement per Sqm, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floor, skirtings etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for coloured glazed ceramic tiles of each size 300x200x7mm / 350x250x7mm / 450x350x7mm as on vertical surfaces of walls, dados, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3, complete all as specified and directed.

M&L for 10mm thick coloured ceramic vitrified tiles, light shade (square/ rectangular), polished, area of each tiles not exceeding 0.38 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, liad/ fixed over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 10mm thick coloured ceramic vitrified tiles, light shade (square/ rectangular), polished, area of each tiles not exceeding 0.38 Sqm as in skirtings/ dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick screed bed in CM 1:3, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in any description and in any position, not otherwise provided for and removing the debris to a distance not exc 500 mtr from site, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position, not otherwise specifically provided for, complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoines, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan, exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, old size, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and directed.

Use and waste of formwork to rough finished concrete sides and soffits of floor or roof, roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splays between floors and beams, complete all as specified and directed.

Use and waste of form work to rough finished concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

Use and waste of formwork to edges of concrete (rough finished surfaces) flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work, exc 10cm but not exc 20cm wide, complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal Mix) type B-1 (using 20mm graded crushed stone aggregates) as in lintel over 1.5 mtr clear span, complete all as specified and directed.

M&L for RCC M-25 (design Mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like and including 15mm thick plastering in CM 1:4 with using water proofing compound, laid/made to slope as in RCC roof surfaces, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

M&L for mild steel TMT bars 6-8mm dia, cut to length, bent to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Dismantling of existing roof treatemnt surface and removal from the site, complete all as specified and directed.

M&L for 10mm thick screed bed in cement mortar 1:3 including finishing the surface even and smooth without using extra cement to receive roof treatment mixed with water proofing compound (ratio of WPC and cement - 2%) over and including a neat cement slurry @ 3 Kg/Sqm over cleaned roof surface as in grading to RCC roof surface including taking down existing cement plaster from top of roof, scrubbing down with water etc. of any description, complete all as specified and directed. Note :- WPC shall be measured and paid separately under respective item of this BOQ.

Supply only integral water proofing compound, complete all as specified and directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B-1 (using 20mm grade crushed stone aggregates), complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg per Sqm over applying primer bitumen coat @ 0.30 Kg per Sqm including cleaning the surfaces, complete all as specified and directed.

M&L for APP modified based polymeric membrane, minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non primed surface over fabric weight not less than 150 Gram per Sqm and applying two coats of aluminium paint over APP membrane, complete all as specified and directed.

S&F in replacement ball valve (minimum weight 210 gms), high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for 20mm bore iron pipe, complete all as specified and directed.

M&L for preparation of new steel/ iron surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enameled paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enameled paint over a coat of pink primer, complete all as specified and directed.

S&F in replacement chromium plated, fancy type, stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions, complete all as specified and directed.

S&F in replacement chromium plated pillar tap, cast copper alloy, fancy type with capstan head, screwed down high pressure with long screwed shank and fly nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including grinding and polishing with rounding to edges of stone slabs one edg complete, laid/ fixed over and including 20mm thick screed be/ plaster CM 1:4, complete all as specified and directed.

Rounding to edges of stone slabs (Granite / Kota) one edge such as in steps, cooking platform and other similar situations, complete all as specified and directed.

S&F in replacement plastic water closet seat cover, white, closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F in replacement health faucet (ABS Body) mild steel chromium plated, suitable for 15mm bore pipe with 1.25 metre long flexible tube, complete all as specified and directed.

S&F in replacement jet spray, brass, chromium plated, heavy duty including flexible pipe, suitable for 15mm bore water connection for EWC, complete all as specified and directed.

S&F stainless stell peg set of 6 with base and fixed to concrete, brick or wooden surface, complete all as specified and directed.

S&F glass soap dish of size 230x100x6mm with stainless steel railling and fixed with stainless steel screws, complete all as specified and directed.

S&F in replacement soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs and brass cromium plated screws, complete all as specified and directed.

S&F glass shelf corner, set of three of size 12'' x 9'' x 6'' with stainless steel railling and fixed with stainless steel screws, complete all as specified and directed.

S&F in replacement centre hole mixer for mixing hot & cold water, suitable for wash hand basin, cast copper alloy with dual capstan heads, chromium plated, screwed down high pressure with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement wall mixer, brass, chromium plated, fancy type with capstan head handles, screwed down high pressure with lettered 'hot' and 'cold', including CP brass wall flanges and necessary extension nipples, screwed for 15mm bore pipe connection, complete all as specified and directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and directed.

S&F in replacement chromium plated tubular towel rail, 'D' type, 600mm long between flanges, complete all as specified and directed.

S&F towel ring of CP, fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90gms), complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.

M&L for mild steel work as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles, conforming to Fe-290 Gde E165, complete all as specified and directed.

M&L for cutting holes in brick walls for hold fast, exc half brick but not exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required at site, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi- corrugated etc.) or CGI sheets in roof coverings including ridges, complete all as specified and directed.

S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with galvanised 8mm dia 'J' hooks or self tapping screws, complete all as specified and directed.

S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with galvanised 8mm dia 'J' hooks or self tapping screws, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, not otherwise provided for, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets, complete all as specified and directed.

S&F false ceiling with everest fiber cement designer tile lvory/ white painted (high pressure steam cured) of 4mm thickness (as per IS-14862) of size 595mm x 595mm and any one of the design (occeanic, lake & hill cascade or electra) in true horizontal level, suspended on interlocking power coated certa black pattern metal grid of hot dipped galvanised steel section (galvanised @12 Grams both side inclusive) consisting of main 'T' runner with suitably spaced joint to get required length and 15x32mm, made of 0.30mm sheet spaced between main 'T' @ 600mm C/C from a ridge of 600x600mm and wall angle of size 15x20mm made of 0.30mm thick sheet and laying false ceiling tile in the grid including required cuttig / making opening for service like diffuser grils light suspended from ciling using GI soffit cleats fixed to existing rafters purlin etc. with dash fastener GI adjustable rod of 3mm dia with galvanised butterfly level clips spaced at 1200mm c/c along main 'T' bottom exposed width of 15mm of all T-sections shall be centre black prepainted with poiyester paint and having a load bearing capicity of 12 Kg/Sqm and re-fixed all existing electric wiring and fixtures, fixed at any height, complete all as specified and directed.

M&L for rolled mild steel work as in tubular trusses, posts, purlines including special shaped, notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (including rivet or nuts and bolts), providing and fitting angle cleats, gusset plates etc. also for welding, plumbing, truing up and fixing complete washers etc, complete using ERW or induction butt welded tubes, conforming to IS:1161-1979 Grade ST-240, complete all as specified and directed.

M&L for 1st class softwood handrails of size (section) 75x60mm, rounded or shaped with splayed faces in straight lengths and fixed, complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation or for shafts, wells, cesspits, manholes, pier holes/ laying of pipes/ cables etc. and getting out in any type of soil, complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling in and mass concrete, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) as in surface channels, drains and benching, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in copings etc. including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 (Nominal Mix) type B-1 (using 20mm graded crushed stone aggregates) as in manhole's covers, cover slabs etc. including necessary formwork and set in cement mortar 1:4, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in bed to drain pipes of bore 150mm including packing under and haunching against the sides of pipes after they are laid and tested including necessary shuttering and supports, complete all as specified and directed. Notes :- (a) Thickness of bed belew/ under pipe -10cm. (b) Width of bed - outer dia of pipe plus 40cm.

M&L for 150mm bore reinforced cement concrete pipe, Class NP-2, jointed complete with collars, laid in trenches, complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick, complete all as specified and directed.

Removing excavated materials / soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Cutting into existing manholes for connecting new drain and making good to pipe and rendering, cutting out to existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished and reforming benching as required for 150mm internal dia of pipe, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base, floor etc, complete all as specified and directed.

M&L for machine pressed cement concrete interlocking paver block, glossy finish, any shape and size, confirming to IS:15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment, complete all as specified and directed.

M&L for 25mm thick sand cushioning to filling in floors/ under paver blocks etc, complete all as specified and directed.

S&F in replacement of waste coupling of PTMT, 32/40mm dia (Mininium weight 32mm - 45 Gms / 40mm -60 Gms), complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation, mass concrete, sub base and floor, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm grade crushed stone aggregates) as in floor, staire case base of tiles/ stone or, leveling course, complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work including welding, conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Dismantling timber scantlings, 40 Sqcm and over in section, in any position, complete all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins etc, under 40 Sqcm in section, in any position, complete all as specified and directed.

M&L for 25mm dia stainless steel curtain rod with stainless steel brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories, complete all as specified and directed. Note :- The cost of brackets and knobs shall be deemed to include in the quoted rate. Nothing extra shall be paid on this account.

M&L for factory made, glossy finished, coloured chequred cement concrete tiles, size of each tile 30cm x 30cm x 25mm thick, machine pressed, set and jointed in neat cement slurry and jointing with white/ grey cement & pigments o match with tiles, laid/ fixed over and including 15mm thick screed bed in CM 1:4 as in floors, complete all as specified and directed.

M&L for stainless steel (Grade 304) railing, made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of floor or the side of waist slab with suitable arrangements, complete all as specified and directed.

Providing precast cement concrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) louvers & jallies, 25mm thick (measured solid), set in cement mortar 1:4 including all mouldings and shuttering, complete all as specified and directed.

Taking down carefully the existing copper / aluminium point wiring of any size and type by disconnecting from the either terminals complete with switches, sockets, ceiling rose, regulators, bell etc. by unscrewing and removing materials to store for keeping in safe custody for re-use or for taking credit and making good to disturbed surface of walls, floors etc. to match with existing surfaces, complete all as specified and direcetd.

M&L for point wiring for one light / fan point, controlled by one one way switch 5 Amp with 1.5 Sqmm single core multi standed copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuos earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn into and including concealed PVC rigid conduit of not less than 25mm dia and 1.5mm wall thickness ISI marked, terminated into annealed steel terminal boxes, flush to surface including 3mm thick hylam brand ISI marked marked laminated sheet cover for mounting switches, sockets, fan regulators etc. complete all as specified and directed.

All as per serial item No. 157.00 here-in-above but for one bell / buzzer point, controlled by one other switch or independent one bell switch.

All as per serial item No. 157.00 here-in-above but for one 5 Amps 3 Pin socket outlet on independent board.

All as per serial item No. 157.00 here-in-above but wire size 2.5 Sqmm to controlled the 3 Pin 5/15 Amps socket outlet on independent board and providing earth continuity wire using PVC insulated, FRLSH 1100 volts grade unsheathed single core multistranded copper conductor cable of size 2.5 Sqmm.

All as per serial item No. 157.00 here-in-above but for 3/5 pin socket outlet 5/6 Amps on same board with other switches.

All as per serial item No. 157.00 here-in-above but one light/ fan point, controlled by two way switch.

S&F switch piano, flush type, single pole, 6 Amps, one way, complete all as specified and direcetd.

S&F socket outlet, two in one, 3 Pin, 5 Amps, complete all as specified and direcetd.

S&F switch piano, flush type, single pole, one way, 15/16 Amps, complete all as specified and direcetd.

S&F socket outlet 2 in 1, 3 pin, 5 and 16 Amp, flush type, complete all as specified and directed.

S&F switch socket combination, 2 in 1, 5 & 15 Amps, flush type universal, complete all as specified and directed.

S&F bell push, flush type, 5 Amp, complete all as specified and directed.

S&F switch piano, flush type, single pole, two way, 6 Amps, complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC polycarbonate isolated body, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type on phenolic laminated sheet as required, complete all as specified and directed.

S&F bell, AC, 230 volts, single pole, complete all as specified and directed.

S&F LED tube light, 1x20 Watt, 220 Volts, AC, PVC housing, PC cover ensures and glare free light IP 20, CRI ≥ 80, PF> 0.90, CCT 6500K, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED tube light, 1x10/12 Watt, 220 Volts, AC, PVC housing, PC cover ensures and glare free light IP 20, CRI ≥ 80, PF> 0.90, CCT 6500K, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED tube light, 1x5 Watt, 220 Volts, AC, PVC housing, PC cover ensures and glare free light IP 20, CRI ≥ 80, PF> 0.90, CCT 6500K, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED light fitting, 1x9 Watt / 1x10 Watt, bulk head luminaires including LED light driver holder IP 20, CRI > 80, PF> 0.90, CCT 6500K connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F LED light fitting, 2x16 Watt, flame proof, CMRI certified, reccomended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP-65 protection with die cast aluminium housing with heat resistant toughened glass with LED tube light fixture driver, holder, connector etc, complete all as specified and direted.

S&F LED street light fitting, 35 Watt, 230 Volts AC, outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-66 protection, complete all as specified and directed.

S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 Volts, 1200mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

S&F exhaust fan, steel body, copper winding, double bearing AC, single phasee of size 300mm sweep, 4 blades, iron frame and iron louver, complete all as specified and directed.

S&F wall mounted fan, steel body, AC single phase, 230 Volts of size 400mm sweep with blades with complete accessories, complete all as specified and directed.

Taking down fan, ceiling cable end, dismantling blades and kept in safe custody for refixing on same location, complete all as specified and directed.

M&L for repair of ceiling fan 1200/1400mm sweep of any make obtained from serial item No. 182.00 here-in-above, oiling, greasing, cleaning slot, overhauling and replacement of defective nuts, bolts, washer etc. including painting. If the fan will be found burnt, the rewinding will be also completed by the contractor as per unit quoted rate, complete all as specified and directed. Note :- Cost for rewinding (if required) shall be deemed to include in the quoted rates.

Hanging / fixing only ceiling / exhaust fan and connecting up including provision of stranded 3 core flexible 1.0 Sqmm copper conductor cable from ceiling rose or connector to fan, complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 Mtr below normal ground level, connected to earth lead wire of Gl wire 4mm dia by means of nuts, bolts and washers, check nuts of galvanized iron or steel including 15mm dia GI pipe light grade upto 1.5 mtr below GL as in protection pipe and including excavation, earth work, charcoal dust, common salt, PCC 1:3:6 type C-1 chamber with RCC cover in cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate), reinforced with 6mm dia round bars @ 75mm c/c both way with MS handle 12mm dia, PGI funnel and wire mesh, connected to earthing test point, complete all as shown in electrical plate No. 3 of SSR Part-l and testing on completion, complete all as specified and directed.

M&L for earth continuity conductor or main earthing lead, fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required, 4mm dia galvanised iron or steel wire, complete all as specified and directed.

S&F 4 way double door TPN sheet metal enclosures, powder coated distribution board with 160 Amps bus bar, neutral link, earth bar and din rail suitable for use isolator 63 Amps, 4 pole, 415 Volts, 50 Hz, IP-43 Protection Grade, fixed flush to wall complete including connections should be provide with necessary reducer lugs, complete all as specified and directed.

S&F isolator, 4 Pole, 63 Amps, 415 Volts, complete all as specified and directed.

S&F isolator, 4 Pole, 100 Amps, 415 Volts, 16 KA including making necessary arrangements, complete all as specified and directed.

S&F in replacement single pole and neutral sheet metal steel powder coated distribution board for MCBs, fitted with bus bar neutral link earth bar and din rail suitable for use on 240 V, 50 Hz, double door, 4 Way, complete all as specified and directed.

S&F in replacement single pole and neutral sheet metal steel powder coated distribution board for MCBs, fitted with bus bar neutral link earth bar and din rail suitable for use on 240 V, 50 Hz, double door, 8 Way, complete all as specified and directed.

S&F double door TPN DB, 4 Way sheet metal enclosure powder coated distribution board for MCBs with100A bus bar neutral link earth bar and din rail suitable for use on 415V, 50 Hz, complete all as specified and directed.

S&F in replacement MCB SPN 32-40 Amps, 240 Volts, rupturing capacity 10 KA "C" Series, complete all as specified and directed.

S&F in replacement MCB SP 6-32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series, complete all as specified and directed.

S&F in replacement MCB SP 63 Amps, 240 Volts, rupturing capacity 10 KA "C" Series, complete all as specified and directed.

S&F in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SPN of 20 Amps, 240 Volts capacity, complete all as specified and directed.

M&L for sub main wiring with two run single core 6 Sqmm FRLS multistandard copper counductor cable PVC insulated, unsheathed, 1100 Volts grade including 25mm dia PVC concealed conduit pipe, medium grade, ISI marked with all accessories such as tees, elbows, junction boxes etc. as required on site alongwith one run of 6 Sqmm single core PVC FRLS insulated unsheated copper counductor cable as continuous earth wire and connecting to exisiting main switch board, complete all as specified and directed. Note :- Two runs of 6.0 Sqmm and one run 6.0 Sqmm cable and one run of PVC conduit shall be measured as one RM/ Unit.

S&F electric water heater, storage type, steel body with copper inner tank and heating element upto 2 KW of capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece, complete all as specified and directed.

M&L for sub main wiring with two run single core 4 Sqmm FRLS multistandard copper counductor cable PVC insulated, unsheathed, 1100 Volts grade including 25mm dia PVC concealed conduit pipe, medium grade, ISI marked with all accessories such as tees, elbows, junction boxes etc. as required on site alongwith one run of 4 Sqmm single core PVC FRLS insulated unsheated copper counductor cable as continuous earth wire and connecting to exisiting main switch board, complete all as specified and directed. Note :- Two runs of 4.0 Sqmm and one run 4.0 Sqmm cable and one run of PVC conduit shall be measured as one RM/ Unit.

Supplying, laying/fixing and testing in replacement XLPE insulated, screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 Core, laid in trenches/ floor/ pole through GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match with the existing surfaces, complete all as specified and directed.

Supplying, laying/fixing and testing in replacement XLPE insulated, screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 Core, laid in trenches/ floor/ pole through GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match with the existing surfaces, complete all as specified and directed.

M&L for dry river sand as in cushioning to underground cables, provided with a layer of sand 8cm thick before laying the cable and 15cm thick after laying the cable and stretching the cable, complete all as specified and directed.

Supply and laying brick class 'B', old size as in covering / mechanical protection to UG cable with well burnt, complete all as specified and directed.

M&L for 40mm bore GI tubing, light grade with all fittings and fixed in wall or laid in trenches/ floor or fixed to pole with MS clamps of suitable size, complete all as specified and directed.

Supply and laying DWC pipe (double wall corruguated) HDPE, PE-100, PN-4, confiming to IS:14930 (Part-ll) alongwith necessary snap fit coupler for interconnection suitable size for protection of LT cable, complete all as specified and directed.

S&F aluminium strip of size 25x3.15mm with saddles and fixing screws, porcelain insulators, rawl plugs etc. for conductor for roof and fixed on wall upto test point including making good the disturbed surfaces, complete all as specified and directed.

S&F galvanised iron strip of size 32x6mm, buried in ground or fixed on wall, mounted on suitable size porcelain insulators (on floor and wall only) including cutting cavities for fixing of porcelain insulators and finishing with cement plaster on wall / floors and connected to test point including bending, jointing at test points with GI nuts, bolts, with lead washers, jointing strips at all joints including making good the disturbed surfaces to match with existing surfaces, complete all as specified and directed.

S&F air termination single pointed aluminum rod of 12mm dia, 300mm long, fixed with 02 Nos sutable sized nuts, bolts and washers including making good the disturbed surfaces to match with existing surfaces, complete all as specified and directed.

S&F test point terminal block, made of gun metal or phosphorous bronge, size 75x75x25mm of 6mm thickness drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head brass screws including box of size 90x90x90mm made of 1.6mm thick plain sheet and screwed to wall for protection of test point, complete all as specified and directed.

M&L for "ASHLOK" make Zinc coated Safe Earthing Electrode (SEE), confirming to IS-3043 ( Code of practice for Earthing) using pipe - in - pipe technology with the help of Zinc coated (80 - 100 microns) Gl pipes, one bag BFC (Back Fill Compound ) including required necessary excavation and earthwork including taking out old existing one, complete all as specified and directed.

M/S GURU DEV BUILDERS (BID ID -3309481)

KUMAR CONSTRUCTION CO (BID ID -3309462)

RAMAN KUMAR (BID ID -3309544)

paras ram pachiala (BID ID -3314376)