COMPREHENSIVE MAINT OF B/R SERVICES IN CERTAIN BLDG AND PERIODICAL SERVICES ETC AT 44 WEU (B) ANUPGARH UNDER GE (AF) SURATGARH

Amount

BOQ (COMPREHENSIVE MAINT WORKS IN ZONE 'A' AKASH VIHAR AT AF STN SURATGARH. )

Demolition of brick work in any position, built in cement mortar, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) of any description in ground floors and paving not exceeding 15cm thick (below or above the ground level), complete all as specified and directed.

Dismantling of floor health or walls tiling and stone floor including cement mortar bedded (but not backing) & removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Demolition of RCC any description in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), complete all as specified and directed.

M&L 75mm thick cement concrete (1:3:6) Type C2, 40mm stone graded aggtas in plinth pritection, finished even and smooth w/o using extra cement, complete all as specified and directed.

M&L for RCC Chajjas in 1:2:4 Type B0 (using 12.5mm graded aggregates) as in approved design, complete all as specified and directed. by engr-in-Charge.

Taking down cement plaster of any description including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L mild steel TMT bars but 8mm dia over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Use and waste of formwork to sides flat surfaces and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc, complete all as specified and directed.

M&L for RCC M-25 (20mm graded aggregates) Beams, cantilevers,bressummers, lintels over 1.5m span, complete all as specified and directed.

M&L for cement concrete M-15 nominal mix 1:2:4 type B0 (12.50mm graded aggregates) filling in cracks, holes, chases by making surface even and alighned, complete all as specified and as directed

M&L for brickwork with subclass 'B' bricks, straight or curved on main plan exc.6m mean radius laid flat, in drains, old size bricks, bedded and jointed and pointed in CM 1:6, complete all as specified and directed

M&L for 5 mm thick , plaster in cement mortar (1:4) on surfaces of ceiling and finishing the surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 15 mm thick cement plaster in CM (1:4) on brick/concrete surfaces, complete all as specified and directed.

M&L, rendering 15mm thick in CM(1:4) on fair faces of brick works , finished the surface as rough cast plaster, complete all as specified and directed.

M&L, rendering 10mm thick cement plaster in cm (1:6) on fair faces of brick works or concrete surfaces , finished even and smooth w/o using extra cement, complete all as specified and directed.

Supply only, integral waterproofing compound, all as specified and directed.

M&L for applying a one coat of oil bound distemper on existing surface of walls preparing old painted surfaces by complete removal of existing treatment through mechanical scarper machine for any type of existing surface of walls, complete all as specified and directed by Engineer-in-charge.

M&L for applying two coats of oil bound distemper over a coat of primer over new surfaces including preparation of new surfaces finished even and smooth using 1mm thick JK wall care putty, complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of exterior acrylic emulsion (weather proof treatment ), in camouflaging patterns, over newly plastered surfaces over a coat of primer, including preparation newly surfaces, complete all as specified and directed by Engineer-in-Charge.

Applying two coats of exterior acrylic emulsion (weather proof treatment), on existing surface of walls preparing old painted surfaces by complete removal of existing treatment through mechanical scarper machine for any type of existing surface of walls over a coat of primer in camouflaging patterns, over old plastered surfaces, including preparation new surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of existing surface of ceiling by complete removal of existing treatment through mechanical scarper machine and applying three coats of white wash, complete all as specified and directed by Engineer-in- Charge.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick, (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm (including size 400mmx400mm), as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6), complete all as specified and directed by Engineer-in-charge.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 15mm thick screed bedding in CM (1:6), complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm for vertical surfaces skirting/dado etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 15mm thick screed bedding in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles of 7 to 8mm thick, (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm (including size 400mmx400mm), as for vertical surfaces skirting/dado etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6), complete all as specified and directed by Engineer-in-charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including screed bed or bedding layer of 15mm thick in CM (1:6) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed or bedding layer of 15mm thick in CM (1:6) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

S&F Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete, as specified, size of frame 105 x 60mm, complete all as specified and directed.

M&L for PCC M-10 (nominal mix) 1:3:6 using 12.5mm graded stone aggregate for filling door frames, complete all as specified and directed.

M&L for 35mm thick factory made panel shutters 2nd class HW rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and directed.

S&F Factory Made Solid PVC Moulded door Shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site, complete all as specified and directed.

S&F 100mm butt hinges, stainless steel medium weight fixed with stainless steel screws, complete all as specified and directed.

S&F, aluminium handles, 150mm size, cast type anodised, complete all as specified and directed.

S&F floor door stopper aluminium body double tounge anodised with hard drawn steel spring 140mm long, complete all as specified and directed.

S&F, Aluminium anodised barrel tower bolts, 150 mm long , of extruded section and fixed, complete all as specified and directed.

S&F, aluminium alloy anodised sliding door bolts, of 250mm long with hasp, staple(bolt type) fixing clips of sheet cast or extruded section, fixing bolts and sliding bolts of extruded section and fixed, complete all as specified and directed.

S&F in repair aluminium anodised tubular curtain rod, 20mm dia, complete all as specified and directed.

S&F bracket for 20 mm dia tubular curtain rod(for item above), complete all as specified and directed

S&F in repair brass 4 Lever mortice lock, vertical type,size 100mm, complete all as specified and directed.

S&F in repair brass 2 lever mortice lock, vertical type,size 100mm, complete all as specified and directed.

Taking down chowkhats or frames/aluminium, steels exc 1.5 sqm but not .exc 4 sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkhats or frames/Aluminium, Steels not. exc 1.5sqm each with shutters (without taking of shutters from the frames ), complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified including powder coating (minimum thicknesss of powder coating 50 micron), complete all as specified and directed.

S&F for powder coated anodised aluminium window and ventilator shutter, side hung type without sash, aluminium sections weighing 0.55kg/m incl necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1No) hinges type B-21 100mm long(2 No) suitable handle (1 No), complete all as specified and directed.

S&F for powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc, complete all as specified and directed.

S&F steel windows with side hung shutter including projecting type hinged, steel peg stay,with glazing bars, steel handles dovetailed type, complete all as specified and directed .

S & F framed work such as grills, gratings etc with ends of bars shouldered and/or revetied or forged into spikes framed guard bars and similar works conforming to Fe-410 or Fe-3100 and embedded in concrete over compound wall incl necessary welding to the existing grills, complete all as specified and directed.

Hacking out old brocken glass of any thickness, size and description not exc 0.50 sqm in each pan matal frame glazing with oil putty or fixed with beadings etc, complete all as specified and directed .

M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each panes, complete all as specified and directed. (Make - SI/Saint Gobin/Modi Guard).

M & L for 4.8mm thick sheet glass ordinary quality and glazing with clips in square exc 0.50 Sqm in each panes, complete all as specified and directed.

M&L Solar control film 25 micron reflective type garware sun control or equivalent, complete all as specified and directed.

M & L for 4mm thick figured glass pinhead type and glazing with oil putty in square not exc 0.50 sqm in each panes, complete all as specified and directed.

S&F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore, complete all as specified and directed .

S&F PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed .

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness with grid of any type and pattern including cover fillets, complete all as specified and directed to engr-in-Charge.

S&F anodised aluminium snap grid of size 605mm x 605mm frame work for false ceiling including supporting hangers of not less than 4mm dia GI rod upto 1.2m length with necessary bolts, nuts and washers, adjusting level fixed to any type of roof, complete all as specified and directed to Engr-in Charge.

M&L for 12mm thick perforated gypsum board fixed in ceiling for insulation or accoustic purpose, flat or sloping fixed to timber frame work or on snap grid with staple pins, complete all as specified and directed to engr-in Charge.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, in hard and dense soil, complete all as specified and directed by Engr-in-Charge.

M&L for plain cement concrete 1:4:8 type D2 (40mm graded aggregate) in foundation filling & mass concrete, complete all as specified and directed.

M&L 100mm thick cement concrete type D-2, 1:4:8 (40mm graded stone agrregate) as sub-base to floor etc, complete all as specified and directed.

Dismantling mild steel work of any driscription and any position, complete all as specified and directed.

Dismantling for Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240, complete all as specified and directed.

S&F mild steel for framed structure like trussed, purlins, crane gantries, post rails and fastenings and heavy bracket framming (Beam, Tee, Angle, Channels, Tube, flate sections) including distance pieces, cleats etc conforming to Fe410-W (Gde-E-250) quality-A, complete all as specified and directed.

S&F mild steel screwas bolt (Machine made) with hexagonal or square heads one end screwed, each screwed end have two washer and one nut, dia of shank 11mm-15mm and length of bolt not exc 5 cm long, complete all as specified and directed by Engr-in-charge.

M&L pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth not otherwise described by applying two coats of synthetic enamel paint over a coat or red oxide zinc chrome primer, complete all as specified and directed.

Repair aluminium door and window shutters by taking down shutter from frame, opening out joints, taking out glass or panels of any description, replacing the corner piece wherever required, joining and assembling again, refixed the glass pane and panels by provision of new rubber neoprene packing, complete all as specified and directed.

Resecuring, easing or adjusting without taking down/window shutters not exceeding 1 sqm for easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws, complete all as specified and directed.

Resecuring, easing or adjusting without taking down/window shutters exceeding 1 sqm but not exceeding 2 sqm for easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws, complete all as specified and directed.

Resecuring, easing or adjusting without taking down/window shutters exceeding 2 sqm for easy operation, tighting hinges, adjusting position of hinges, tower bolts, sliding bolt etc including provision of necessary screws, complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept, bore of pipe 15mm, complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept bore of pipe 20mm, complete all as specified and directed.

Dismantling of water tanks and removing to store capacity of tank exc 250 and not exc 500 ltr, complete all as specified and directed.

Dismantling of water tanks and removing to store capacity of tank not exc 500 and n exc 1000 ltr, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I ,500 ltr capacity including, 20mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I,1000 ltr capacity including, 20mm dia ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F Medium grade GI tubing 15mm bore with all fittings , to walls, ceiling or laid in floors etc.complete all as specified and directed.

All as per item No- 83 above but in 20mm bore pipe, complete all as specified and directed.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe 15mm bore pipe, complete all as specified and directed.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe 20mm bore pipe, complete all as specified and directed.

S&F for stop valve copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15mm bore in repairs, complete all as specified and directed.

S&F bib taps 15mm dia cast copper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and directed.

S&F in repairs angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms), complete all as specified and directed.

S&F in repairs Viterious china White Wash Hand Basin including 15mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32mm dia & 15mm PTMT connection pipe 450 mm long, complete all as specified and directed.

S&F in repairs soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair CP Tubular towel rail with hook 20 mm dia 600mm long between flanges of fixed with and including chromium plated brass screws and wooden/plastic screws, complete all as specified and directed.

S&F in repair vitreous china bowl urinal flat back, size 465x355x265mm white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe, complete all as specified and directed.

S&F in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32mm bore, connecting to WC with PVC telescopic pipe, complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia for WHB ISI marked, complete all as specified and directed.

S&F in repair PVC coupling for WHB 32mm dia, complete all as specified and directed.

S&F in repair 32mm Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms/40mm-270 gms), complete all as specified and directed.

S & F Grating round 140 mm size of PTMT. (Minimum weight 50gms), complete all as specified and directed.

M&L pillar taps, 15mm bore cast copper alloy chromium plated , with capstan heads, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe fixed as in repair, complete all as specified and directed by the Engineer in Charge.

S&F in repair 15mm size PVC connection with PTMT nuts 650mm length, complete all as specified and directed.

S&F in repairs small galvanized iron fittings such as socket, elbow, nipple, tee, union etc for 15mm bore pipe, complete all as specified and directed.

Opening of air lock/blockage in GI pipe line from service water tank to internal GI pipes. Fittings for smooth flow of water to bib taps/ showers/pillar tap/stop valve complete by application of pressure pump/gravity pressure, complete all as specified and directed.

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 17 of tender documents.

Gaurav India Corporations (BID ID -3125802)

MAHADEV ENTERPRISES (BID ID -3137427)

M/s JUGAL KISHORE MISHRA AND SONS (BID ID -3129272)

MSR INFRATECH (BID ID -3136989)