Construction of office building of DDUCE-OF at CCS HAU, Hisar. (including public health and electrical works)

Amount

Civil work 1 to 161:- EARTH WORK AND ROCK CUTTING Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil (HSR 4.4.1)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. (HSR 4.14.1)

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil (HSR 4.31.1)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. (HSR 4.32)

Providing and injecting chemical emulsion for PRE CONSTRUCTIONAL anti termite treatment and creating a chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filing junction of wall and floor, along with the external perimetre of building, expansion joints surrounding of pipes and conduit etc, complete (plinth area of the building at ground floor only shall be measured) using Chlorpyriphos/ Lindane emulsifiable concentrate of 20% (HSR 4.39)

Disposal of earth by mechanical transport including loading, unloading for a lead upto 10 Km. (HSR 3.1.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) (HSR 6.1.2)

CONCRETE AND RCC WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) (HSR 6.1.6)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor four level, excluding the cost of centering, shuttering and finishing: 1 :2:4 (1 Cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size) (HSR 6.2.2)

1 :3:6 (1 cement : 3 coarse sand (zone-Ill) : 6 graded stone aggregate 20 mm nominal size) (HSR 6.2.3)

Extra for providing and mixing water proofing material in cement 50 kg concrete work in doses by weight of cement as per manufacture r's specification. (HSR 6.5)

Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) 50 mm thick (HSR 6.8.1)

Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 sqm cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (HSR 6.13)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works up to plinth level (HSR 6.25.1)

All works above plinth & up to floor IV level (HSR 6.25.2)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases of columns, etc. for mass concrete (HSR 6.30.1)

Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc. (HSR 6.30.2)

Suspended floors, roofs, landings, balconies and access platform (HSR 6.30.3)

Shelves (Cast in situ) (HSR 6.30.4)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (HSR 6.30.5)

Columns, Pillars, Piers, Abutments, Posts and Struts (HSR 6.30.6)

Stairs, (excluding landings) except spiral-staircases (HSR 6.30.7)

Small lintels not exceeding 1.5 m clear span, sqm moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like (HSR 6.30.15)

Edges of slabs and breaks in floors and walls Under 20 cm wide (HSR 6.30.16.1)

Weather shade, Chhajjas, corbels etc., including edges (HSR 6.30.19)

Weather shade, Chhajjas, corbels etc., including edges (HSR 6.30.19)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and sqm balconies (Plan area to be measured) (HSR 6.32.1)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D kg or more. (HSR 6.33.6)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D kg or more. (HSR 6.34.6)

Providing and fixing in position Stainless steel Grade 304 plate 1.0 mm thick as per design for expansion joints. 200 mm wide. (HSR 6.60.1)

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminium base members, self aligning/ self centering arrangement and support plates etc. as per ASTM 9221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical location in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminium base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer's pre-engineered self centering arrangement that freely rotates I moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminium extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm gap (HSR 6.61.1)

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminium base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to comer application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminium profiles exhibiting minimal exposed aluminium surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). Wall Joint of 100 mm gap (HSR 6.62.1)

BRICK WORK AND STONE MASONRY Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.21.2)

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.22.2)

Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in foundations and plinth in: Cement mortar 1:3 (1 cement: 3 coarse sand) (HSR 7.27.1)

Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in foundations and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR 7.27.2)

Half brick masonry with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level. Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR 7.28.2)

Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. sqm bars at every third course of half brick masonry (HSR 7.30)

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor IV level in cement mortar 1 :4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos. 6 mm dia M.S. bars at every third course of masonry work. (HSR 7.50)

Providing and laying autoclaved aerated cement blocks masonry with 150mrn/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor IV level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in Charge. (The payment of RCC band and reinforcement shall be made for separately). (HSR 7.51)

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. (HSR 8.3)

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. (HSR 8.5)

CLADDING WORK Stone work (machine cut edges) for wall lining etc. (veneer work) up to 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1 :3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) Gang saw cut stone 30mm thick Red sand stone (HSR 8.9.3.2)

Wall lining butch work up to 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1 :3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge. (HSR 8.12)

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. Ki ln seasoned and chemically treated Hollock wood (HSR 8.18.1)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfonns, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab up to 0.50 sqm (HSR 8.26.2.1)

Area of slab over 0.50 sqm (HSR 8.26.2.2)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work (HSR 8.27.2)

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platfonn, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (HSR 8.28)

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1 :2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade (HSR 8.30.2)

ROOFING 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1 :3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class sqm designation 10 (HSR 9.11.1)

Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (HSR 9.17.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of oaintina with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) (HSR 9.46.1)

FLOORING AND DADOS Providing and laying of base course of floors consisting of 100 mm thick sqm cement 1 :8: 16 and 100 mm sand or stone filling. (HSR 10.1)

Providing and laying Cement concrete flooring 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate (HSR 10.10.1)

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : 25 mm thick (HSR 10.37.1)

Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (HSR 10.38)

Extra for pre finished nosing to treads of steps of marble stone. (HSR 10.45)

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge: Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (HSR 10.49.1)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (HSR 10.50.1)

Providing and fixing granite stone in all shades 15mm to 18 mm thick in skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of Granite including labour for fixing cramps pins and dowels etc. (HSR 10.51)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (HSR 10.58)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. (HSR 10.61)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (HSR 10.63.2)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm (HSR 10.63.4)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm (HSR 10.67.2)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 1000x1000 mm (HSR 10.67.4)

FINISHING WORKS 6 mm cement plaster of mix 1 :3 (1 cement : 3 fine sand) (HSR 11.1.1)

12 mm cement plaster of mix : 1 :4 (1 cement: 4 coarse sand) (HSR 11.8.1)

15 mm cement plaster on rough side of single or half brick wall of mix: 1 :4 (1 cement: 4 coarse sand) (HSR 11.9.1)

20 mm cement plaster of mix 1 :4 ( 1 cement: 4 coarse sand) (HSR 11.10.1)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C projections. (HSR 11.54)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. (HSR 11.59)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (HSR 11.60)

White washing with lime to give an even shade New work (three or more coats) (HSR 11.61.1)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer (HSR 11.64.1)

Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work (HSR 11.71.1)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 11.78)

Painting the wooden / metal surface with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work (HSR 11.82.1)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm (HSR 11.94.1)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 litre/1 O sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (HSR 11.95.1)

WOOD WORK Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick (HSR 12.12.1)

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid separate 12mm thick commercial ply conforming to IS: 1328 BWR type (HSR 12.22.1)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screw (HSR 12.37.1)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). (HSR 12.39)

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). (HSR 12.42)

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. (HSR 12.81)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 250x10 mm (HSR 12.99.2)

150x10 mm (HSR 12.99.4)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm (HSR 12.102.1)

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper (HSR 12.103.2)

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 Nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer- in-charge Extruded section profile size 48x40 mm (HSR 12.117.1)

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 :t 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all comers, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window/ ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 :t 0.2 mm and single glazing bead of appropriate dimension. (Area up to 0.75 sqm) (HSR 12.132.1)

Providing and fixing factory made uPVC white colour sliding glazed window up to 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x B mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof S.S wire mesh (Two Nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). (HSR 12.134.4)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded lnline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) crescent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all comers, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm up to 5.00 sqm) (HSR 12.136.1)

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete (HSR 12.140)

Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete (HSR 12.141)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) (HSR 12.157.1.2)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) (HSR 12.157.2.2)

Providing and fixing glazing in aluminium / uPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 6 mm thickness (weight not less than 15 kg/sqm) (HSR 12.159.3)

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) (HSR 12.159.4)

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Powder coated minimum thickness 50 micron aluminium tubular handle bar (HSR 12.163.2)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Up to 5mm depth and 5 mm width (HSR 12.169.1)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). (HSR 12.171)

STEEL WORK Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 140 mm (HSR 13.5.4)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).(HSR 13.41)

Compacting Original Ground Compaction of Earthwork Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers) (HSR 17.5.3)

Granular Sub-Base with Close Graded Material· (Table:- 400-1) Plant mix method Construction of granular sub-base by providing Material as per Grading Ill (Table 400-1 of MORT&H 5th revision) mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications Grading I material (HSR 17.14.1)

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Subbase over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15: 1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing, as per clause 601 of MORT&H specifications. (HSR 17.44) Note:- Quantity provided for aggregate is for estimating purpose. Exact quantity shall be as per mix design

Cement Concrete Pavement Construction of un-reinforced M-40 grade concrete pavement with dowel jointed, over a prepared sub base with 43 grade OPC cement concrete coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a fully computerised batching and mixing plant as perapproved mix design, transported to site in transit mixer with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing, complete as per clause 602 of MORT&H specifications.(HSR 17.45)

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS: 164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matte, demarcation at site and traffic control Over 10 cm in width (HSR 34.24.1)

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1 :3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately}. Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1 :3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudrn/sqm thoroughly embedded in the 2nd layer Using rough kota stone (HSR 28.10.1)

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1 :3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge. Using rough Kota stone (HSR 28.13.1)

Providing and applying of swellable type water stop tape, 19mm x 25mm thick metre in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc .. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3. 78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage. (HSR 28.30)

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. (HSR 33.12)

Supplying, filling, spreading & levelling gravels of size range 5 mm to 1 O mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (HSR 33.13)

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (HSR 33.14)

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. (HSR 33.15)

WATER PROOFING Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) llnd course of 20 mm cement plaster 1 :3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) lllrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) lvth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen@ 1.7 kg/sqm). (HSR 28.14)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 1 O cm. (c) third layer of 1.5 mm thickness consisting of sluny of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately). For the purpose of measurement the entire treated surface will be measured. (HSR 28.16.1)

Providing and laying cinder concrete in cement 1 :15 (1 cement and 15 cinder) on terraced roofs & (up to three Storeys), laid to slope, including consolidating the same. (HSR 28.27)

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge. (HSR 28.41)

STRUCTURAL GLAZING AND ALUMINIUM COMPOSITE PANEL Providing and supplying aluminium extruded tubular and other aluminium kg 360 360 sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to MMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. (HSR 29.1)

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.29.6) For payment, only the actual area of glass on face# 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating approved make having properties as visible Light transmittance (VL n of 25 to 35 %, Light reflection internal 1 O to 15%, light reflection external 1 O to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. (HSR 29.2)

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge. (HSR 29.3)

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, non combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminium sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete. (HSR 29.4)

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface# 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face# 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevant Item). "(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VL T) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0. 25- 0.28) and U value of 3.0 to 3.3 W/m 2 K etc .. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. (HSR 29.5)

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part Ill (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminium sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (HSR 29.6) (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in�harge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge Notes for Item 29.6: 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm up to two decimal places. 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. 3. Competent authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. 3.1. Performance Laboratory Test for Air Leakage Test (-50pa to· 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 3.2. Static Water Penetration Test (50pa to 1500pa) as per ASTME· 331· 09 testing method for a range up to 2000 ml. 3.3 Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01· 05 testing method for a range up to 2000 ml 3.4 Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range up to 50 mm 3.5 Seismic Movement Test (up to 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 3.6 Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) up to 2000 ml (HSR 29.6)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance i!: 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick bevelled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 (HSR 32.47.1)

Earth filling under floors with dune sand (tiba sand)/earth, brought from outside (any lead), in 15 cm layer including laying, dressing, watering ramming, consolidating, excavation, carriage, loading, unloading and compensation, etc., complete. (NS)

Earth filling under road/parking with dune sand (Tibba sand) brought from outside (any lead) in 25 cm. layer including laying, dressing, watering, rolling with road roller to specifications/ consolidating, excavation, carriage, compensation, loading and unloading, complete in all respects. (NS)

Providing and fixing factory manufactured cement concrete 1:2:4 kerb finished smooth and of size 1’-0” x 1’-0” x 0’-6” of required shape and design fixed at ground level along with road parking, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Providing and fixing factory manufactured cement concrete 1:2:4 channel finished smooth and of size 1’-0” x 1’-0” x 0’-3” of required shape and design fixed at ground level along with road, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Providing & fixing Wooden veener false ceiling comprising of the following: Frame work : Channels of size 0.55mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brick wall/partition with the help of nylon sleeves and screws, at 610mm centers. The suspending GI intermediate channels of size 45mm 0.9mm thick with two flanges of 15mm each from the soffit at 1220mm centers with ceiling angle of width 25mm x10mm x 0.55mm thick fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 457mm centers. All sections, channels, etc to be in Gypsteel make as specified by manufacturer as per shown in drawing and directed by the Architect. Including making all necessary trap door shutter, Include marking the positions of light fittings & AC grilles and making necessary cut-outs and providing independent wooden framework for AC grills, lighting fixtures, & providing additional framing to support the cutouts etc. Quoted Rates are for all heights , scaffolding, depths, levels, leads and lifts and for all design and pattern shown in drawings. Contractor to include the cost of members & all required accessories for installation complete finished ceiling in his quoted rate. All necessary hardware ( hettich/Hafel make ) shall be inclusive in the quoted cost. (NS)

Providing and installing Engineered wooden Flooring of size 1900mmx190mmx14mm having top layer veneer 3mm thick in approved shade make and design fixed nail down with tongue & groove joint, over 5mm thick foam sheet including adhesive, profiles, T's, skirting, moulding, beading etc all complete as per drawings and as directed by Engineer-in-charge. Make Junker, Vista, Pergo, Armstrong (NS)

Providing & Fixing Hi Steel Aluminum Clip-in False Ceiling System is manufactured out of 0.70mm. These tiles shall have square (90 degree) edges. Two sides of each tile are raised and piped and stopped to ensure positive engagement into the spring Clip-in profile, yet allow for demounting of individual tiles. The rigid suspension system consists of rows of 0.5 mm galvanized 120gsm/M2 steel Clip-in profiles of size 38 mm X 20 mm and installed at 600 mm c/c spacing to support the tiles, clip-in profiles are suspended and jointed from galvanized steel C Channels of size 10 mm x 38 mm x 10 mm with hold on clamps. Suspension Angles are suspended from the roof structure by GI Ceiling Brackets and joint to the C Channels. The tiles are held in place by pressure clips. In the flexible system the Hanger and suspension Clip replace the suspension angle. Wall angles or edge profiles are of size 24 mm X 24 mm and 0.4 mm thick with matching the color with tiles. Including all necessary trap door shutter including making opening for lights, AC grills etc. complete as per design and drawing. (Contractor to include the cost of members & all required accessories for installation compelet in his quoted rate) Hi Steel Aluminum Clip-in False Ceiling System with tile (600 mm x 600 mm) in server room (NS)

Providing & fixing Wooden veener false ceiling comprising of the following: 4mm thick veneer finish ( Duro group A) over 12mm thick commercial ply (Century/ Green/ Kitply/ Garnet) with hard wood (Beeachwood) frame of required section fixed to wall & ceiling with necessary nails & screws as required and as per drawing. Veneer Make: Duro , Commercial Ply Make: Century/ Green/ Kitply/ Garnet Including all necessary nails, glues, teak wood lipping, melamine polishing, wood preservative paint, fire retardant paint, brushed steel hinges for trap door shutter including making opening for lights, AC grills etc. complete as per design and drawing. (Contractor to include the cost of members & all required accessories for installation compelet in his quoted rate) (NS)

Providing and laying Double Charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x1200 mm (NS)

Providing and laying Double Charge Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x1200 mm (NS)

Providing and laying Anti Skid vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm (NS)

Providing and laying leather finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :. Leather finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (NS)

Providing and applying plaster of paris (super fine quality) punning with minimum thickness of 6mm and finish the surface smooth in line and also making groove, level to the entire satisfaction of Architect including scraping and hacking the existing finished surfaces, scaffolding etc. complete as per drawing. (NS)

Providing and Installation of Funder Max for cladding on exterior Surface 6mm thick Exterior grade F- Quality panels of standard size with both side décor . The Panels shall be perforated as per the design of the Architect. FunderMax Exterior panels are duromer high-pressure laminates (HPL) as per EN 438-6 type EDF manufactured with norm conformity of EN 438-7 using patented NT Technology (NT is Non fading high performance acrylic polyurethane surface Technology). Panels will be double hardened including acrylic polyurethane resin and thermally cured under high pressure. These Panels will have CE-Mark necessary for their use in building applications. Installation of FunderMax panels will be done by MBE Rivets (with Fixed and Sliding Points) with recommended Aluminum T section of 100x50x2 mm thick and L section 50x50x2mm thick held by Aluminum Wall Bracket with Wind load and Dead load slot as per design, anchored by standard anchor fasteners along with Thermal Separator. Installation of FunderMax Panels will be done using Rear Ventilated Principles only, which is ensured by providing ventilation gap minimum 200 cm2/ per Meter (for free flow of air behind the façade) for the façade and using the framework with no horizontal section. (NS)

MISCELLANEOUS Providing and fixing in position 1000mm high Glass railing made of 15mm thick toughened glass fixed to floor with Metal framing of required section including Stainess steel top rail of section 75x50mm of polish finished fixed on top of the glass, including SS U channel fixed as per drawing with grinding, silicon sealent, cutting holes in civil work to fix the frame in position, fastners wherever required etc. complete with all necessary fixing arrangement( Grade of stainless steel to be considered - 304 )(Shop drawing of railing and Sample approved by the Architect before execution. (NS)

Providing and fixing White mark make of white righting boards of the all sizes. Rates of the white board to be inclusive of accessory kit like pen stand, duster, magnets etc. (NS)

Providing and fixing Fabric Board. Rates of the Fabric board to be inclusive of accessory kit like pen stand, duster, magnets etc. (NS)

Providing and fixing frosted film make film on Glass Partition with MCS warranty of 5 years as per the manufacturer specification. (Finished works to be measured as smt). To include cost of printing designing, and sample approvals. 3M forsted film on glass as per design Ref. Name & No.: Dusted Crystel white 7725 - 314 Dot pattern or as per architect approval applied on glass with full/half frosting (As per Design) (NS)

Providing and fixing 45 mm wide solid and 30 mm wide jali Zebra type (PCL rainbow or any other equivalent make as approved by Engineer In charge) horizontal venetian blinds of required size and shape, fixed in position including rawl plugs and screws etc. complete in all respect (NS)

Provoding and Fixing Logo for DDUCE/CCSHAU WITH TEXT AND LOGO for main reception area made with S.S and Back Led lighting of approved color as shown in drawing or as directed by the architect. (NS)

Provoding and Fixing Signage in area's such Lift Lobby for Floor Indication etc. Toilet signages (Gents)- on door : Acrylic ducopainted signage with text / graphics in 3M grade vinyl Size : 200 mm wide x 200 mm tall * sign mounted on door (NS)

Provoding and Fixing Signage in area's such Lift Lobby for Floor Indication etc. Toilet signages (Ladies)- on door : Acrylic ducopainted signage with text / graphics in 3M grade vinyl Size : 200 mm wide x 200 mm tall * sign mounted on door (NS)

Floor Level Indicator - wall mounted : (LIFT LOBBY) Acrylic ducopainted signage with text / graphics in 3M grade vinyl Size : 317 mm wide x 317 mm tall * sign mounted on wall (NS)

Floor Level Indicator - wall mounted : (LIFT LOBBY) Acrylic ducopainted signage with text / graphics in 3M grade vinyl Size : 317 mm wide x 317 mm tall Fire Exit Door Signages (NS)

Cabin / Room Naming (In vinyl on glass) : Ht. 30mm, Font : Expert sans regular, Length Max. 450 mm Ref. : Colour 100 % cyan. 4 colour process C100 MO to KO. RGB : R0 G164 B232 (NS)

Desk Numbering (NS)

Supply & Installtion of Pull - Push Signages : Brush finish stainless steel etched signs Size : 2.5"(H) x 2.5"(W) set includes 1 pull & 1 push (NS)

Providing and fixing 6mm thick (of any shape & size ) fixed with 40mmx40mm hard wood frame of ivory cost teek wood section as shown in the drawing, mirror with 12 mm thick waterproof ply backing supported with 20mm thick water proof board fixed to wall with hard wood pegs including providing and fixing 300 micron HDP film as vapour barrier, all necessary fixing arrangement like nails/ screws dash fastner, wood preservative paint, providing and fixing polythene bubble sheet between mirror and backing ply, stainless steel caping to bolt head, melamine polish on wooden frame etc. complete. All visible wood would be steam beech (NS)

Furniture work Reception Table Dimension(L)3000mm X (D)750mmX (H)750mm (all over ht 1050mm) Supplying, and placing in position of reception Table as per Image/drawing . The table top are made up of 36mm thick pre-laminated particle board and understructure shall be made of 25mm thick prelaminated particle board with 2mm thk pvc edge banding . Modesty & side panel shall be 25mm thk prelam particle board with 2mm thk pvc edge banding . Table top height will be 750mm from the floor level & one additional top at the height of 300 mm above the table top rest on SS stud/prelam vertical panel . overall ht of the table 1050mm. The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of Prelam particle board Mobile pedestal of size 400mm(L)x 450mm(D) x 600mm(HT) (2 drawer + 1filling). Pedestal Top are made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The product should be from a company which have Greenguard,BIFMA member, FSC & AIOTA certification of Approved make Godrej/ Wipro . Complete as per reference image and specification as mentioned above under the guidance of project Architect and Engineer in Charge. (NS)

Conference Table Dimension: 26936mm(overall circular (L) x 600mm (D) X 750 (H) Supplying and placing in position of conference room table of the following dimensions as per image/drawing . The conference table should be provided in module of 2 seater. The dimensions for two person seating: 1350mm(L) X 600mm(D) X 750mm(H). The work surface top should be of thickness 42mm thk top made out of prelam particle board with 2mm thk pvc edge banding. The side panels are made up of 32mm thk prelam particle board & modesty panel are made out of 25mm thk prelam particle board with 2mm thk pvc edge banding. The legs of the table should be Made from 32mm prelam particle board with 2mm thk pvc edge banding . The wire carrier should Made from 0.6mm thick CRCA & powder coated 40-50 microns . Also provision of 6 module fliptop box & metal raceway for wire flow. The product should be from a company which have Greenguard, BIFMA member, FSC & AIOTA certification of Approved make Godrej/Wipro . Complete as per reference image and specification as mentioned above under the guidance of project Architect and Engineer in charge. (NS)

Public Health work 162 to 303:- Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia (HSR 4.16.1.2)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 15 mm diameter pipe (HSR 11.107.1)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 20 mm diameter pipe (HSR 11.107.2)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 25 mm diameter pipe (HSR 11.107.3)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work 32 mm diameter pipe (HSR 11.107.4)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 40 mm diameter pipe (HSR 11.107.5)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 50 mm diameter pipe (HSR 11.107.6)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality 40 mm diameter pipe (HSR 11.108.5)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality 50 mm diameter pipe (HSR 11.108.6)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 32 mm internal diametre of pipeline (HSR 20.20.2.4)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 40 mm internal diametre of pipeline (HSR 20.20.2.5)

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading Including cost of specials 50 mm internal diametre of pipeline (HSR 20.20.2.6)

Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS: 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge (HSR 21.28)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 150mm i/d (HSR 21.94.2)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. 200mm i/d (HSR 21.94.3)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White vitreous chinaware Wash basin size 630x450 mm with a single 15 mm C. P. brass pillar tap (HSR 22.1.2)

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (HSR 22.2.1)

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 510x1040 mm bowl depth 250 mm (HSR 22.10.1.1)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia (HSR 22.14.2.1)

40 mm dia (HSR 22.14.2.2)

Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required. Single half stall urinal with 5 litre P.V.C. automatic flushing cistern (HSR 22.26.1)

Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern (HSR 22.26.3)

Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. (HSR 22.33)

Providing and fixing floor mounted, white vitreous chinaware single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous chinaware cistern of capacity10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. (HSR 22.34)

Providing and fixing toilet paper holder C.P. brass (HSR 22.42.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal outer dia Pipes (HSR 22.85.5)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes (HSR 22.86.1)

20 mm nominal outer dia Pipes (HSR 22.86.2)

25 mm nominal outer dia Pipes (HSR 22.86.3)

32 mm nominal outer dia Pipes (HSR 22.86.4)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 15 mm dia nominal bore (HSR 22.88.1)

20 mm dia nominal bore (HSR 22.88.2)

25 mm dia nominal bore (HSR 22.88.3)

32 mm dia nominal bore (HSR 22.88.4)

40 mm dia nominal bore (HSR 22.88.5)

50 mm dia nominal bore (HSR 22.88.6)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc External work 40 mm dia nominal bore (HSR 22.91.5)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc External work 50 mm dia nominal bore (HSR 22.91.6)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore (HSR 22.92.1)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 50 to 80 mm nominal bore (HSR 22.92.2)

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main 25 mm nominal bore (HSR 22.100.3)

45 cm length 15 mm nominal bore (HSR 22.101.2.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (HSR 22.103.3)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore (HSR 22.104.1)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (HSR 22.106.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (HSR 22.108.1)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (HSR 22.117)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. (HSR 22.118)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design 150 mm diameter S.W. pipe (HSR 22.164.2)

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design 250 mm diameter S.W. pipe (HSR 22.164.4)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 150 mm diameter S.W. pipe (HSR 22.165.2)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 200 mm diameter S.W. pipe (HSR 22.165.3)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design 300 mm diameter S.W. pipe (HSR 22.165.5)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common bumt clay non-modular bricks of class designation 7. (HSR 22.166.3.1)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 150 mm dia. R.C.C. pipe (HSR 22.168.2)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 250 mm dia. R.C.C. pipe (HSR 22.168.3)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 (1 cement: 2 fine sand) including testing of joints etc. complete 300 mm dia. R.C.C. pipe (HSR 22.168.4)

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1 :4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1 :2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1 :5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1 :3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.173.1)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (HSR 22.181)

Constructing brick masonry manhole in cement mortar 1 :4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1 :4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 :3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.190.1.1)

Constructing brick masonry manhole in cement mortar 1 :4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1 :4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 :3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.190.2.1)

Extra for depth for manholes : Size 90x80 cm With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.191.1.1)

Extra for depth for manholes : Size 120x90 cm With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.191.2.1)

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1 :4 (1 cement : 4 coarse sand) including 500x450 mm pre­ cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay non-modular bricks of class designation 7.5 (HSR 22.205.1)

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (HSR 22.209)

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P. brass screws and rawl plugs etc. complete including cutting and making good the walls etc. C.P Brass Two Way (HSR 22.212.1.2)

Providing and fixing in position best Indian make (to the approval of the engineer-in-charge) storage type automatic electric water heater, pressure/non-pressure type thermostatically controlled, suitable for operation on 230 volts, 50 cycles single phase vertical wall mounting fitted with-draw able and adjustable type AC, thermostat. Thermostat knob to be readily accessible through the opening of suitable cover for and adjustment of temperature in the installed position of heater and the thermostat should be withdrawn without having to drain the water, electric heating element made out of copper tube (heating element should be easily removed and replaced in the installed position of heater) A neon indicator 1 AMP, inner container made out of copper tinned both from inside and outside, outer container made out of mild steel sheet finished in gleaming white stove enamel paint, insulated between the inner and outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord with plug and non return valve plastic/lead connections or pressure release valve (where required). Complete including fixing and testing for a week (as required by Engineer-incharge. 30 Litres capacity (HSR 22.216.2)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 160 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.1)

110 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.2)

90 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.3)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 metre depth below ground level. All types of soil 400 mm dia (HSR 33.6.1.3)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & up to 150 metre depth below ground level. All types of soil 400 mm dia (HSR 33.7.1.3)

Supplying, assembling, lowering and fixing in vertical position in bore well, Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia (HSR 33.8.3)

Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia (HSR 33.9.3)

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. (HSR 33.12)

Supplying, filling, spreading & levelling gravels of size range 5 mm to 1 O mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (HSR 33.13)

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (HSR 33.14)

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. (HSR 33.15)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 200 mm dia (HSR 33.16.3)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete 200 mm clamp (HSR 33.17.3)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 200 mm dia (HSR 33.18.3)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yieldwithout sand content (beyond permissible limit), with requiredcapacity air compressor, running the compressor for requiredtime till well is fully developed, measuring yield of well by "V''notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. (HSR 33.19)

Providing and fixing C.P brass health Fancet with 1 mtr flexible tube and swivel hook including all fittings, complete in all respect. (NS) Make:- Jaquar/Hindware

Providing and fixing stainless steel 600 mm Grab Bar with 2 mtr C.P brass wall flanges including cutting and making good the walls wherever required, complete in all respect (NS) Make:- Jaquar/Hindware

Providing and fixing water purifier cum water cooler made of fully stainless steel body having storage capacity of 80 ltrs & cooling capacity 60 ltrs/hour with reverse osmosis system. (NS) Make:-Bluestar/Voltas/Usha Kent/Aquaguard

Supply of UPVC pipe 6 kg/cm² pressure (as per IS: 4985 Class-II) of Prince / Supreme/Skipper/Finolex make (as approved by the Engineer-in-Charge). (NS) a) 40 mm o/dia size (32 mm i/dia)

(b) 50 mm o/dia size (40 mm i/dia)

c) 63 mm o/dia size (50 mm i/dia)

Providing and fixing in position UPVC 'P' or 'S' trap of self cleaning design of 110 mm inlet and 110 mm outlet for embeded areas and making connection with chemical sealent joint, cutting chase/hole in floor/slabs etc.and making good in cc 1:2:4 complete in all respect.(NS)

Providing and fixing in position UPVC floor drain including cost of cutting and making good the wall and floors wherever required. 110 mm inlet and 63 mm outlet (NS)

Providing and fixing UPVC clean out plug (ceiling or floor) with suitable insert keys for opening male threaded joint with UPVC socket fixed to UPVC pipe complete in all respect. (NS) (a) 110 mm dia

(b) 160 mm dia

Providing and fixing stainless steel Grade (304) grating with ring and stainless steel anti cockroach basket and two stainless steel screw including fixing to the floor with cement morter. (NS)

Providing and fixing thermoflex or careflex thermal insulation tubing, a elastromeric flexible material having hermatix blister closed cell structure of expanded synthetic rubber over pipes of following sizes and thickness including all required accessories. (a) For 15 mm dia pipes (NS)

(b) For 20 mm dia pipes

Providing and fixing commissioning of motorised butterfly valves (for filling of overhead tanks) complete with high and low level control switches to control tanks the level controller shall be installed in overhead tanks, the level switch will close the valve when water level is high and open the valve when water level in tank is low, the system should be complete in all respect with accessories 220V AC/ 24V DC/IP 67 electrical water level control unit, copper control wiring in whether proof casing etc. Make:- Belimo/Audco/ Advance/ AIP. (NS) (a) 40 mm dia pipe

(b) 50 mm dia pipe

Providing and fixing Full way lever operated brass ball valves of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 15kg/sq cm with threaded/ flanged points complete with nuts, bolts, gasket, washers etc. (a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

(d) 32 mm dia

(e) 40 mm dia

(f) 50 mm dia

Providing and fixing G.I pipes complete (15:1239 medium class) with G.I fittings coupling to 15:1879 and clamps including M.Spipe supports, paiting with two or more coats of synthetic enamal paint including one coat of primer and cutting and making good the walls etc. complete internal work:- Exposed on wall. (a) 65 mm dia pipe

(b) 80 mm dia pipe

(c) 100 mm dia pipe

Providing and fixing C.I butyterfly valves lever operated PN-1.6 complete with bolts, nuts 1.5 mm thick compressed asbestos gasket and two nos flanges etc. complete in all respect (a) 65 mm dia nominal bore

(b) 80 mm dia nominal bore

(c) 100 mm dia nominal bore

Making connection of drain or sewerline with existing man hole including breaking into and making good the walls, floors with c.c. 1:2:4 course sand mix cement plaster on both side 1:3, finished with a floating coat of neat cement and making necessary channel and drain etc. complete in all respect. (i) For pipes100 to 250 mm dia

(ii) For pipes 250 to 300 mm dia

Supplying and Fixing Air Vessel made of 450 mm dia 8 mm thick ms sheet 2000 mm in height with air release valve on top and flanged connection to riser drain arrangement with 25 mm dia gunmetal wheel valve with required accessories pressure gauge and painting with synthetic enamel paint of approved shade as required. (NS) Make:- Lubi/Xylem/Ebara

Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc in ground including welding excavation and Providing cement concrete blocks as supports anticorrosive treatment with coaltar / asphalts tape as per IS :10221 refilling the trench etc of following sizes complete as required. 150 mm dia (NS) Make:- Jindal/TATA/Ravindra/Parkash (Surya)

80 mm dia (NS)

Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers , nuts , bolts , gaskets etc and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required . 25 mm dia (NS) Make:- Jindal/TATA/Ravindra/Parkash (Surya)

80 mm dia

100 mm dia

150 mm dia

Supplying and Fixing Single Headed Internal Hydrant Valve with instantaneous gunmetal coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS : 5290 ( Type A ) with blank Stainless Steel cap and chain as required . Single Headed Gunmetal (NS) Make:- NVR/Zoloto/Kartan

Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers , gaskets conforming to IS : 13095 of following sizes as required . 80 mm dia (NS) Make:- NVR/Zoloto/Kartan

100 mm dia

150 mm dia

Supplying and Fixing orifice plate made out of 6 mm thick stainless steel ( Grade 304 ) with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg / sqcm complete as required .(NS)

Providing Installation Testing and Commissioning of Non Return Valve of following sizes conforming to IS : 5312 complete with rubber gasket , GI Bolts , Nuts , washers etc as required . 100 mm dia (NS) Make:- NVR/Zoloto/Kartan

150 mm dia

Providing Installation Testing and Commissioning of Stainless Steel Y Strainer fabricated out of 1.6 mm thick stainless steel , Grade 304 , Sheet with 3 mm dia holes with stainless steel flange . (NS) 150 mm dia Make:- SPAGO/Safeguard/Minimax

Supplying and Fixing 63 mm dia 15 m Long RRL Hose pipe with 63 mm dia male and female coupling duly bound with GI wire , rivet etc . Conforming to IS : 636 ( Type A ) as Required . (NS) Gunmetal Material Make:- SPAGO/Safeguard/Minimax

Supplying and Fixing First aid hose reel with MS Construction Spray painted in Post office red conforming to IS : 884 complete with the following as required 20 mm nominal internal dia water hose thermoplastic ( Textile Reinforced ) Type - 2 as per IS : 12585 20 mm nominal internal dia gunmetal globe valve and nozzle Drum and Brackets for fixing the equipments on wall Connections from Riser with 25 mm dia stop gunmetal valve and MS Pipe and socket 36.5 Metre Length (NS) Make:-SPAGO/Safeguard/Minimax

Supplying and Fixing 63 mm dia Gunmetal Short Branch Pipe with 20 mm nominal internal diameter size nozzle conforming to IS : 903 suitable for instantaneous connection to interconnect hose pipe coupling as required Gunmetal Material (NS) Make:-SPAGO/Safeguard/Minimax

Supplying and Fixing of Fire brigade connection of Cast iron body with gunmetal male intantaneous inlet coupling complete with cap and chain as required for suitable dia ms pipe connection conforming to IS : 904 as required 2 Way 100 mm dia MS Pipe (NS) Make:-SPAGO/Safeguard/Minimax

Supplying and Fixing Air Vessel made of 250 mm dia 8 mm thick ms sheet 1200 mm in height with air release valve on top and flanged connection to riser drain arrangement with 25 mm dia gunmetal wheel valve with required accessories pressure gauge and painting with synthetic enamel paint of approved shade as required (NS) Make:-SPAGO/Safeguard/Minimax

Providing and Fixing of Pressure Switch in MS Pipe Line including connection etc as required (NS) Make:-SPAGO/Safeguard/Minimax

Providing and fixing of Fire Hose Cabinet size not less than 2.1 x 1.2 x 0.90 mtr made out of M.S. sheet not less than 1.5 mm thick having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside 'with the letters "FIRE HOSE" including necessary locking arrangement and painting in PO red colour suitable to accommodate, internal hydrant valve, 2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It shall be fixed inside the FHC Cabinet Complete as required . (NS) Make:-SPAGO/Safeguard/Minimax

Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Tested to a pressure of 20 Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required. 100 mm dia (NS) Make:-SPAGO/Safeguard/Minimax

150 mm dia

Providing and fixing standard firemans axe with heavy rubber handle.(NS) Make:-SPAGO/Safeguard/Minimax

Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-16 / sq. cm. (NS) Make:-SPAGO/Safeguard/Minimax

Providing and fixing Fire Extinguishers (CO2 type powder ) 4.5 Kg Capacity complete with all accessories as per manufacturers specifications.(NS) Make:-SPAGO/Safeguard/Minimax

Providing and fixing Fire Extinguishers (A, B, C type powder ) 6 Kg Capacity complete with all accessories as per manufacturers specifications. (NS) Make:-SPAGO/Safeguard/Minimax

Providing and fixing Fire Extinguishers (A, B, C type powder ) 9 Kg Capacity complete with all accessories as per manufacturers specifications. (NS) Make:-SPAGO/Safeguard/Minimax

Electrical work 304 to 494:- Wiring main ,sub mains and Circuit wiring in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in MS Conduit etc as required. (HSR 23.1.6.1) 1 run of Size 1.50 Sqmm(1/1.40mm)

1 run of Size 4 Sqmm(1/2.24mm) (HSR 23.1.6.3)

Wiring for Light/Fan/call bell point with modular type switch/socket and GIbox, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe. (HSR 23.2.1.2 ) Group B

Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe.(HSR 23.2.3.2 ) Group B

Wiring in MS conduit system for 3-pin Samp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required (HSR 23.2.4.2) Group B

Wiring in MS conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required (HSR 23.2.5.2) Group B

Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.(HSR 23.6.6.2) MS pipe of 25 mm dia.

Supply and erection of PVC conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.(HSR 23.7.6.2) PVC pipe of 25 mm dia.

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections,complete in all respect. Electric buzzer 220/230 volts A.C. Bakelite with double coil. (HSR 23.8.1.7)

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C.slab for the erection of fan complete with all labour and material required to complete the job. (HSR 23.8.4)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (HSR 23.8.10.1) 1 & 2 Modules

3 Modules (HSR 23.8.10.2)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.(HSR 23.8.11.1) 5 amp 1 way switch

5 amp Socket (HSR 23.8.11.4)

step type Fan Regulator 2 modules 300 watt (HSR 23.8.11.7)

Blanking plate (HSR 23.8.11.10)

Telephone Socket outlet modular type (HSR 23.8.11.8)

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work (HSR 23.22.1.3) TRIPLE POLE MCCB 16 to 100 Amp, 25 KA

TRIPLE POLE MCCB 200 to 250 Amp, 25 KA (HSR 23.22.1.5)

TRIPLE POLE MCCB 400 Amp, 25 KA (HSR 23.22.1.6)

TRIPLE POLE MCCB 600 to 800 Amp, 50 KA (HSR 23.22.1.8)

Supply and erection of sheet steel enclosures 1poIe/2 pole/4 pole on wall/on existing pedestal complete as required.(HSR 23.22.3.3 ) TPN enclosure suitable for TP , TPN or FP MCB

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:-(HSR 23.22.5.1) SP MCB 6-32 AMP

SPN MCB 6-32 AMP (HSR 23.22.5.3)

SPN MCB 40-63 AMP (HSR 23.22.5.4)

TPN MCB 40-63 AMP (HSR 23.22.5.8)

SITC Four pole ONLOAD Manual change over switch in SS enclosureof followingRatings (HSR 23.22.8.5) 400 amp 415 volts

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channe l and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-incharge of the work.(HSR 23.23.8.1) 2 pair telephonewire

4 pair telephonewire (HSR 23.23.8.2)

Earthing with G.I earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. as required. (HSR 24.1.1)

Extra for using salt and char coal/coke for pipe earth electrode as required. (HSR 24.1.2)

Earthing with G.I. earth plate 600mm x600 mmx 6 mm thick including accessories and provinding masonry enclosures with cover plate having locking arrrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required. (HSR 24.1.3)

Earthing with tinned copper earth plate 600mm x600 mmx 3 mm thick including accessories and provinding masonry enclosures with cover plate having locking arrrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required. (HSR 24.1.4)

Extra for charcoal or coke and salt for G.I./Copper plate earth electrode. (HSR 24.1.5)

Supplying and laying 25mm x 3mm G.I. strip in 40mm dia, GI pipe as / from earth electrode including soldering etc. as required. (HSR 24.1.7)

Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. (HSR 24.1.8)

Providing and fixing 25mm x 5mm copper strip in 40mm dia G.I.pipe from earth electrode as required. (HSR 24.1.9)

Providing and fixing 25mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. (HSR 24.1.10)

Pdg and laying earth connections from earth electrode with 4.00 mm dia G.I wire in 15 mm dia G.I. pipe from earth electrode as required. (HSR 24.1.11)

pdg and fixing 4.00 mm dia G.I. wire on surface or in recess for loop earthing as required. (HSR 24.1.13)

Supply and erection of suitable compression type brass cable glands for underground Cable :-(HSR 24.2.7.2) 10 sqmm to 16 sqmm cable 2 to 4 core

25 sqmm to 50 sqmm cable 2 to 4 core (HSR 24.2.7.3)

240 sqmm cable 3 to 3½ Core (HSR 24.2.7.6)

300 sqmm to 400 sqmm Cable 3 to 3½ Core (HSR 24.2.7.7)

Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work.(HSR 24.2.8.4) 16 sqmm

50 sqmm (HSR 24.2.8.7)

185 sqmm (HSR 24.2.8.12)

240 sqmm (HSR 24.2.8.13)

400 sqmm (HSR 24.2.8.15)

Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge. (HSR 24.4.8.5) 7 Metre Long pole with top dia 75 mm and bottom dia 150 mm with base plate of size 300 x 300 x 20 mm

S/E of mark double walled corrugated ( DWC) HDPE pipe 10 kg/sqcm, laid 0.75 Mtr. Below ground level including diging and refilling of earth including cost of suitable size socket/ cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer incharge of the work. (HSR 24.5.2.3) DWC/HDPE pipe 63/50 mm outer dia/inner dia

Pdg. And fixing of insulated rubber mating suitable for 11 KV installation 1 M x 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per directions of Engineer-in-charge (HSR 20.84)

DG SETS Designing , Supply & erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 +(-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel , making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer , outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge . The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 V. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator, control fuse, frequency meter, CT's) h) Metering set 60/5A/110V (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k) Copper bus bar of suitable size I) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running , load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge Make:- Kirloskar, Cummins 20.89.10 ) 250 KVA (HSR 20.89.10)

Providing RCC foundation of M20 grade (1 Cement:1.5 Stone aggregate: 3 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 50 kg/cum of concrete contents, concrete cover 50mm, over a bed of 75mm thick PCC 1:5:10, of required dimensions as per OEM recommendations to provide levelled surface for placement of the DG set complete in all respects and as per directions of Engineer-in-charge. (HSR 24.7.5) (Size of foundation assumed = 5.0x1.8x1.0m) Unit: per cum 24.7.5 ) 250 KVA DG Set

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 2x16 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 4x25 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 4x50 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 3.5x185 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 3.5x240 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable laid 1 mtr below ground level with sand and bricks including refilling of trench complete with necessary connecitons:- (NS) Size 3.5x240 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (NS) Size 3.5x400 sqmm (Armoured) Make:-CCl,Havells,Finolex

Supply & erection of under ground cable laid 1 mtr below ground level with sand and bricks including refilling of trench complete with necessary connecitons:- (NS) Size 3.5x400 sqmm (Armoured) Make:-CCl,Havells,Finolex

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 1.5 sqmm Make:-Havells,Finolex,Powerage,RR,LS

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 04 sqmm Make:-Havells,Finolex,Powerage,RR, LS

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 06 sqmm Make:-Havells,Finolex,Powerage,RR,LS

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (NS) Size 16 sqmm Make:-Havells,Finolex,Powerage,RR,LS

Supply installation testingan commissioning of wall free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2 mm thick CRCA sheet required hardware 3 mm thick bakelite sheet providing all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of zinc/Red oxide primer followed by 2 coats of powder cating in grey or required shade after rinsing. the panle having PU/Neoprene rubber gasket of not less than 3 mm thickness separate detachable gland plate MS base channel hinged door with inter locking arrangement for equipment/ switch wear.Transparent arcylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3 mm thick for separately cable alley to BBC from switch chamber Extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra tiems side walls and cable alley compartments shall be haiving bolted type doors with detachable extension type strcture. the panel will be complete with control wiring ( copper) and fuse protection ( only outer area on all sides shall be measured ) (NS)

Supply and fixing of copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing go same in existing panel including bending, cutting in required shape and size and insulation with colour coding heat srinkable PVC insulation complete in all respect. (NS)

S/E of AC ceiling fan capacitor type complete with shackle 5 star rating, 300mm down rod etc. (NS) i) 1200mm sweep. Make: Usha, Orient, Crompton

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod etc. (NS) i) 1400mm sweep. Make: Usha, Orient, Crompton

S/E of LED street light of system voltage ≤ 70/72 W IP 66 Multiple LED with lens optics and pressure die-cast aluminium housing for effective thermal management. Total system lumen of ≤ 70 watt LED should be 8400 or above in cool day light (5700K), Lumen efficacy > 120 lm/W, Power factor ≥ 0.95, CRI ≥70, Average life ≥50000 hours, complete with all acessories as required with connections. Make Havells , Bajaj , Philiphs. (NS)

S/E of Single Arm bracket 1.5 mtr long 40 mm dia GI bracket with suitable sleeve as per pole top dia galvanied with all petty material required to complete the job for entire satisfaction of Engineer in Charge. (NS)

S/E of Double Arm bracket 1.5 mtr long 40 mm dia GI bracket with suitable sleeve as per pole top dia galvanied with all petty material required to complete the job for entire satisfaction of Engineer in Charge.(NS)

S/E of LED tube rod ≤ 20watt double side connections with 4 feet long housing made of CRCA sheet steel with epoxy powder coated white after phosphochromate treatment and 2 nos. lamps push fit type white polycarbonate holders and reflector made of white powder coated CRCA sheet total system lumen of 20watt LED should be >2200 or above in cool day light ( 5700K to 6500K ) PF > 0.95 , CRI >80 , Avg. life >50000 hours complete with mounting bracket and accessories as required with connections Make PhilIphs , Havells , wipro , Bajaj ( NS )

S/E of recessed type ≤42 watt full window glare free opal difffuse LED panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 5100 or above in cool day light (5600k to 6500k), Power factor >0.95, CRI (Ra) >80, LED lamp efficiency ≥140 lm/w, Average life >50000hours, complete with all accessories. (Industrial) Make Havell's or Philiphs , Bajaj (NS)

S/E of Exhaust Fan size 300mm 12" With necessary earthing arrangements of fan with shutter complete in all respects Size 12" sweep Heavy duty 900RPM Make Orient , Usha , Khaitan ,Crompton (NS)

S/E of fancy pole of 3 mtr long made of cast iron base part and mild steel grooved pipe section and joined together by means of threaded joints alongwith a service window provided in the bottom part of the pole to accomadate a 6 amp. SP MCB and 30 amp. Connector for mains connection. A cast aluminium embellishment shall be fitted to the grooved steel pole by grub screw fixing to enhance the decorative look of the pole. The Pole shall be duly pre-treated by shot blasting process and painted in Poly-Urethane paint in approved colour shade having a minimum 300 salt spray hours quoting on the pole and should have minimum 90 micrones DFT. Pole Make : Twinkle, Homdec Lighting LED. Specifications:- LED should be ≤ 30 watt with cast amuminium housing diffuser translucent poly carbonate having quoting PU/Polyster LED should be ≤ 30 watt with seprate driver placed integrally in luminaire housing. Driver should be of THD ≤10% and power factor above ≥ 0.95, provided. LED lumen should be ≥ 3600. The luminaire Urethane/Polyster quoting in required colour shade. LED CCT should be 3000K ingress protection IP 65, power rating 230 volts, AC 50 HZ. LED Make :TWINKLE/K-LITE (NS)

Pdg. and fixing of precast RCC (1:1½:3) cable route marker of size 01 mtr. Deep / 0.75 mtr. Width 0.15 mtr. Thick 0.25 mtr. Below top of side wall and proper embedded in wall. The writing words, L.T. cable on three sides of route markers including arrow on two sides with approvrd make of enamel paint of yellow colour including white colour Apex of approved make 6 nos. horizontal strips for tor steel bar 8 mm dia and 6 nos. vertical tor steel bar 12 mm dia as instruction and as entire satishfaction of the Engineer in Charge of the work. (NS)

Supply, Installation and commissioning of 1 x 40 KVA UPS Each UPS of 20 KVA/36 KW should have following specifications in addition to tender requirements : True online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/ three phase output with SMF batteries Suitable for 30 Min backup on Full load (40 KVA) at 0.8 output power factor. Input voltage range 360-478V at 100% load, 220-478 V @ 50% load. Input power factor 0.99,Output THD is less than 3% for linear load. Less than 5 % for nonlinear load. Crest factor 3:1, over load 125% for 10 min, 150% for 1 min and should be able to operate continuously at 115% load on bypass mode. Battery voltage Adjustable from 384VDC to 480 VDC on site. Battery Bank sizing as 42 AH x 40 nos. X 1 String. Battery type should be Valve regulated lead-acid (VRLA) of make Exide/Panasonic/QUANTA/Rocket. Audible noise level should not exceed 63 dB (A). Parallel communication port, RS232. USB EPO and SNMP interface, BMS interface are required. EMC-IEC62040-2 safety-IEC62040 II operating temperature 0-40 deg C, relative humidity 95% Non-Condensing. No derating e to 40 Deg temp.. UPS shall have inbuilt Input Isolation Transformer. static by pass and manual by pass built in required. Third party test report through accredited lab like TUV is required for IEC 62040-3 and IP20. UPS should be provided with environment monitoring probe to measure temperature and humidity of UPS room. UPS shall have dust filter sat Air Inlet level to improve UPS reliability. LCD Display indicating all important parameters. SNMP software should be compatible to Microsoft windows XP, Windows Vista, Window 8, Window server 2003 R2, UPS software should be compatible to google chrome, Mozilla fire fox and Microsoft internet explorer. Battery rack, battery interlinks battery breaker, battery to UPS cable as required should be provided with UPS systems. (NS) Make: Elnova, Eaton, Peagasus,GE,Gutor

Supply, erection of 0.51 mm jelly filled armored telephone cable laid one mtr. below ground level including the cost of digging, bricks, rawl & laying charges, complete in all respect with the entire satisfaction of Engineer-in-charge. (NS) (i) 50 Pair Make:- DELTON/ FINOLEX/ HAVELLES/LS

Supply, erection of 0.51 mm jelly filled armored telephone cable loose in existing pipe/tranches including testing & commissing charges, complete in all respect with the entire satisfaction of Engineer-in-charge. (NS) (i) 20 Pair Make:- DELTON/ FINOLEX/ HAVELLES

Supply, erection of 0.51 mm jelly filled armored telephone cable loose in existing pipe/tranches including testing & commissing charges, complete in all respect with the entire satisfaction of Engineer-in-charge. (NS) (i) 50 Pair Make:- DELTON/ FINOLEX/ HAVELLES/LS

Supply, erection, laying and testing of D.P. including the cost of krones, base plate, 40mm dia G.I. pipe for incoming and outgoing cable and main box having locking arrangement. (NS) (i) 20 pair DP Make:- DELTON/ KONE

Supply, erection, laying and testing of D.P. including the cost of krones, base plate, 40mm dia G.I. pipe for incoming and outgoing cable and main box having locking arrangement. (NS) (i) 50 pair DP Make:- DELTON/ KONE

SITC of AMF Panel for one no. 250 KVA DG set with all necessary accessories/ items to make connections and accommodate the AMF function. Complete with all Petty required to full fill the job upto the entire satisfaction of Engineer -in charge. (NS)

S/E of POP-Up box with two No.05AMP Socket,one no. telephone & one no. internet jack, with necessary connection complete in all respect. (NS) Make:- DLINK/AMP/R&M

Pdg & fixing of cable manager for internet,telephone & electrical cable on table including the cost of all petty material required to complet the job upto entire satisfaction of Engineer-in-Charge (NS) Make:- DLINK/AMP/R&M

Supply , Installation , Testing and Commissioning of Aircooled Variable Refrigerant Flow Modular Type Airconditioning System suitable for both heating & cooling with Inverter Scroll Compressor for 415 ± 10% volt, 50 Hz., 3 phase AC for Outdoor Unit including fully charged with R-410A refrigerant to outdoor unit and all running refrigerant pipe as per given specification.It shall include vibration Isolator Pads for outdoor units.The outdoor units shall be able to operate between -5 to 52 Deg Celcius.The compressor should be of same manufacturer as of the outdoor unit. The outdoot unit should have inbuilt auto-phase corrector ,that unit can work uninterrupted during phase reversal.The outdoor shall also have accumulator to avoid liquid backflow in compressor.including Backlit type LCD corded & cordless remote controller with Four Zone occupancy and floor temperature Sensor controlling system & Y-joint , Copper joint included complete in all respect. Make Mitsubhsi Electric / Trane / York / Fijutsu O General (NS ) ODU- 22 HP ( Nominal Cooling Capacity)

ODU- 24 HP ( Nominal Cooling Capacity) (NS)

ODU- 28 HP ( Nominal Cooling Capacity) (NS)

Supply , Installation , Testing and Commissioning of Indoor Units for variable refrigerant flow airconditioning system suitable for 220 ± 10% volt, 50 Hz, 1 phase AC supply equipped with synthetic washable media type filters arranged for convenient cleaning and replacement fan section with low noise fan, multispeed motor, coil section with DX (Direct Expansion) coil, Electronic Expansion Valve, outer cabinet, insulated drain pan, built in drain water lift-up pump, pipe connections, fresh air intake etc.with minimum capacity as given below as per specifications .The unit shall also have sensing technology so that it can detect presence of people and floor temperature can be sensed, to provide comfort & energy saving. Make Mitsubhsi Electric / Trane / York / Fijutsu O Genera Four Way Flow Cassette Type with inbuilt Four Zone occupancy and floor temperature Sensor with Cassette Panel ( NS ) 1.0TR Four way cassette/600 CFM

1.3TR Four way cassette/636 CFM (NS)

1.6TR Four way cassette/671CFM (NS)

2.0TR Four way cassette/671CFM (NS)

2.6TR Four way cassette/812CFM (NS)

3.3TR Four way cassette/1024CFM (NS)

4.0TR Four way cassette/1236CFM (NS)

Supply , Installation , Testing and Commissioning of Touch Screen Type Central Corded Centralised Type Remote Controllers capable of monitoring and controlling all Outdoor and Indoor Units etc. as required. The Central Control Unit shall be Touch Screen Type suitable for ON/OFF and Temperature Control of areas including scheduling, Malfunction and status display. Setting of address for each Unit should be automatic and need not be programmed. (NS)

Supply , Installation , Testing and Commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger. (NS) 41.1 mm O.D (wall Thickness-1.4 mm) (Insulation: 19 mm)

34.9 mm O.D (wall Thickness-1.2 mm) (insulation : 19 mm) (NS)

28.6 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) (NS)

22.2 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) (NS)

19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) (NS)

15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) (NS)

12.7 mm O.D (wall Thickness-0.8 mm) (insulation : 13 mm) (NS)

9.5 mm O.D (wall Thickness-0.8 mm) (insulation : 13 mm) (NS)

6.4 mm O.D (wall Thickness-0.8 mm) (insulation : 13 mm) (NS)

Drain Piping Providing and fixing rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. 40 mm dia (NS)

32 mm dia (NS)

25 mm dia (NS)

Control & Transmission Wiring - Providing & fixing control cum transmission wiring of sheilded type 2 core x 1.5 sqmm copper in suitable conduits between indoor and out door unit. (Make- Finolex, RR , Havell,s) (NS)

Supply & erection of cable tray made out of 2 mm thick galvanized perforated sheet steel including erection of the same on wall or ceiling with necessary fixture and other material required to complete the Job in all respect upto the entire satisfaction of Engineer-in-Charge of the work ( NS ) 300mm * 50mm*50mm

600mm * 50mm*50mm (NS)

SITC of IP panoramic camera shall be discreet, aesthetic, low-profile camera for indoor use. The 1/2.3-inch CMOS 12MP sensor operating at 30 fps provides full panoramic surveillance with complete area coverage. Used pixels 3000 x 3000. Lens 1.26 mm fixed-focus lens (IR corrected). 360° Infrared Illumination 20m ; Dynamic range 120 dB WDR. Video compression H.265; M-JPEG.Multiple channels with edge dewarping. Regions of Interest (ROI). Intelligent Video Analysis Features (min. 6 rules simultaneously) :- Rule based alarms and tracking Line crossing Enter /leave field Follow route Loitering Idle / removed object People counting Crowd density estimation 3D tracking; Object filters: Duration, Size, Aspect ratio, Speed, Direction, Color, Object classes ; with on board Machine learning processor (camera trainer) ; 3 built-in digital Micro Electro-Mechanical System (MEMS) microphones; Calibration / Geolocation Automatic based on gyro /accelerometer data and camera height. HDMI Output. Operating temperature -40ºC to +55ºC; Operating humidity 5% to 93% RH non-condensing. IP66 and IK10 Certificates: UL, FCC, EN including Sensor type1/2.9 inch (NS)CMOSTotal sensor pixels3072 (H) x 1728 (V)Sensitivity Color 0.5 lx, Mono 0.08 lx, 0.0 lux with IR (Measured according to IEC 62676 Part 5)High Dynamic range120 dB WDRWDR approved & measured as per OECF analysis according to IEC 62676 Part 5, it should be more than 100 dBTrue Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable)Video resolution5.3MP, 4.1MP, 3MP, 1080P, 720P, SD, D1, VGAVideo compressionH.265 MP, H.264 MP; M-JPEGMax. frame rate1 to 20 fps (5.3 MP)1 to 25 fps (4.1 MP)Lens type2.8 mm fixed, F1.6IR Illuminator15m (49 ft)IR IntensityAdjustableDetection Range of ObjectsUp to 57m (188ft) as per EN-62676-4Audio communicationTwo-way, full duplexAudio Line InBuilt-in mic Audio Line Out1Alarm In/Out 1/1Ethernet10/100 Base-T, auto-sensing, half/full duplexEthernet connectorRJ45ConnectivityONVIF Profile S, ONVIF Profile G & ONVIF Profile TAnalysis TypeEdge Based AnalyticsAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimationOther functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotMin. 512 GB supportSD card health monitoringExtreme lifetime and health monitoring support that provides early service indicationProtocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationEncryptionTLS1.0/1.2, AES128, AES256Data Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patchesHardware for data security Unique Crypto-processor / TPMDual Power Supply for redundancyPOE and 12VDC simultaneouslyOperating temperature-20 ºC to +50 ºC (-4 ºF to +122 ºF)Humidityup to 93% relative humidity (non condensing)Impact protectionIK08Water / Dust protectionIP42Certifications: CE, FCC, UL, VCCI, BIS, ISO 14001including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of HD IP Dome camera with1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.24 lx (color) 0.05 lx (mono) ,IR range 15 mtrs, Dynamic range 120 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering ,People Counting; Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Lens 2.8 mm, True day/night, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording); No cable pigtail ; Memory card slot (support upto 1TB), 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE, UL, FCC Certified. IK08 including Sensor type1/2.9 inch CMOSTotal sensor pixels3072 (H) x 1728 (V)Sensitivity Color 0.5 lx, Mono 0.08 lx, 0.0 lux with IR (Measured according to IEC 62676 Part 5)High Dynamic range120 dB WDRWDR approved & measured as per OECF analysis according to IEC 62676 Part 5, it should be more than 100 dBTrue Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable)Video resolution5.3MP, 4.1MP, 3MP, 1080P, 720P, SD, D1, VGAVideo compressionH.265 MP, H.264 MP; M-JPEGMax. frame rate1 to 20 fps (5.3 MP)1 to 25 fps (4.1 MP)Lens type2.8 mm fixed, F1.6IR (NS)Illuminator15m (49 ft)IR IntensityAdjustableDetection Range of ObjectsUp to 57m (188ft) as per EN-62676-4Audio communicationTwo-way, full duplexAudio Line InBuilt-in mic Audio Line Out1Alarm In/Out 1/1Ethernet10/100 Base-T, auto-sensing, half/full duplexEthernet connectorRJ45ConnectivityONVIF Profile S, ONVIF Profile G & ONVIF Profile TAnalysis TypeEdge Based AnalyticsAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimationOther functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotMin. 512 GB supportSD card health monitoringExtreme lifetime and health monitoring support that provides early service indicationProtocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationEncryptionTLS1.0/1.2, AES128, AES256Data Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patchesHardware for data security Unique Crypto-processor / TPMDual Power Supply for redundancyPOE and 12VDC simultaneouslyOperating temperature-20 ºC to +50 ºC (-4 ºF to +122 ºF)Humidityup to 93% relative humidity (non condensing)Impact protectionIK08Water / Dust protectionIP42Certifications: CE, FCC, UL, VCCI, BIS, ISO 14001 including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of HD IP Dome camera with1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.24 lx (color) 0.05 lx (mono), Dynamic range 120 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering, People Counting; Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Lens 2.3 mm, True day/night, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording); No cable pigtail ; Memory card slot (support upto 1TB), 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE, UL, FCC Certified. IK08 including Sensor type1/2.9 inch CMOSTotal sensor pixels3072 (H) x 1728 (V)Sensitivity Color 0.5 lx, Mono 0.08 lx, 0.0 lux with IR (Measured according to IEC 62676 Part 5)High Dynamic range120 dB WDRWDR approved & measured as per OECF analysis according to IEC 62676 Part 5, it should be more than 100 dBTrue Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable)Video resolution4.1MP, 3MP, 1080P, 720P, SD, D1, VGAVideo compressionH.265 MP, H.264 MP; M-JPEGMax. frame rate1 to 20 fps (5.3 MP)1 to 25 fps (4.1 MP)Lens type2.3 mm fixed, F2.2IR Illuminator15m (49 ft) IR IntensityAdjustableDetection Range of ObjectsUp to 37m (121ft) as per EN-62676-4Audio communicationTwo-way, full duplexAudio Line InBuilt-in mic Audio Line Out1Alarm In/Out (NS)1/1Ethernet10/100 Base-T, auto-sensing, half/full duplexEthernet connectorRJ45ConnectivityONVIF Profile S, ONVIF Profile G & ONVIF Profile TAnalysis TypeEdge Based AnalyticsAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimationOther functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotMin. 512 GB supportSD card health monitoringExtreme lifetime and health monitoring support that provides early service indicationProtocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationEncryptionTLS1.0/1.2, AES128, AES256Data Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patchesHardware for data security Unique Crypto-processor / TPMDual Power Supply for redundancyPOE and 12VDC simultaneouslyOperating temperatureup to 93% relative humidity (non condensing)-20 ºC to +50 ºC (-4 ºF to +122 ºF)HumidityImpact protectionIK08Water / Dust protectionIP42Certifications: CE, FCC, UL, VCCI, BIS, ISO 14001 including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of high resolution 4.1MP HD dome camera with inbuilt Machine learning processor, 1/1.8‑inch CMOS, Effective pixels 2688x1520 (4.1MP) 60fps, Sensitivity IEC 62676 Part 5 (1/25)-Color 0.008 lx,Mono 0.0008 lx, Lens :- 4.4 to 10 mm, 140 dB Dynamic range, Day/night, White balance, Electronic shutter, BLC, Privacy Masking, iDNR , Quad streaming, Full duplex / half duplex Audio Streaming, Dual Memory card slot, Pan, Tilt, Roll and Zoom (PTRZ) for fast installation, Intelligent Video Analytics, Camera Trainer, Password protection, ONVIF S profile, CE, UL, FCC Certified. IP66 Housing IK10+. including Sensor type 1/1.8 inch CMOS SensorTotal sensor pixels2688 x 1520 2.9 μm pixels, 4.1MP (approx.)Sensitivity (IEC 62676 Part 5 (1/25, F1.3))Color 0.0078 lx, Mono 0.0008 lxWDR approved & measured as per OECF analysis according to IEC 62676 Part 5, it should be more 108 dB; HDR 141 dBTrue Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable)Video resolution4.1MP 2688 x 1512, 3MP 2304 x 1296, 2.8MP (4:3) 1920 x 1440, HD 1080p 1920 x 1080, 1.3MP 1536 x 864, 1.3MP (5:4) 1280 x 1024, HD 720p 1280 x 720, SD 432p 768 x 432, SD 480p (4:3) 720 x 480, VGA (4:3) 640 x 480Video compressionH.265 MP, H.264 MP; M-JPEGMax. frame rate1-60 fpsLens type4.4 to 10 mm P-iris lens (IR corrected); F-stop 1.3 - 1.97Lens adjustmentUp to 121 m as per EN-62676-4Detection Range of ObjectsMotorized zoom/focus; rollAudio communicationTwo-way, full duplexAudio Line (NS)In/Out44197Alarm In/Out2 supervised inputs / 1 outputAuxiliary power output for external devices+12 VDC, max 50 mAEthernet10/100 Base-T, auto-sensing, half/full duplexSurge protectionEthernet: 1 kV, 2 kA to ground (8/20 μs pulse)Ethernet connectorRJ45ConnectivityONVIF Profile S, G & TAnalysis TypeEdge Based Analytics with Machine learning capabilityAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking, Audio detection (if microphone used), AI Trainer, Machine learning for Camera to Train the camera to detect customized objects.Other functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotDual SD Card Slot up to 2TB.Dual SD-card slot configurations• Mirror (redundant storage)• Failover (extended service interval)• Extend (maximum retention time)• Automatic Network ReplenishmentSD card health monitoringExtreme lifetime and health monitoring support that provides early service indicationProtocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationEncryptionFull end-to-end encryption with supported VMSNetwork: TLS1.0/1.2, AES128, AES256Local storage: XTS-AESData Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patches· Video authentication checksum, MD5, SHA-1, SHA-256Hardware for data security Unique Crypto-processor / TPMSimultaneous Dual Power Supply for redundancyPOE and 12VDC/24VACOperating temperature-50 °C to +60 °C (-58 °F to +140 °F)Humidityup to 90% relative humidity (non condensing)Ingress protectionIP66, IP6K9K and NEMA Type 4XImpact protectionIK10+ (50 joules)Certifications: CE, FCC, UL, ROHS, BIS including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of HD Outdoor IR IP bullet camera with 1/2.9‑inch CMOS, Sensor pixels 4.1 MP 2720 x 1530, Sensitivity-0.4 lx (color) 0.05 lx (mono) ,IR range 30 mtrs, Dynamic range 100 db, True day/night, Automatic Electronic Shutter, Video compression H.265 MP ; M-JPEG, White balance, BLC, quad-streaming, Video Analysis with minimum 4 analytics run simultaneously ( Object removal , Loitering , Enter or Exit from the Field , Object Classification etc.), Privacy Mask, Auto Varifocal Lens (zoom / focus) 3.5mm to 10 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 (live and recording), 5s pre-alarm recording Memory card slot support upto 512 GB , IP66 , ONVIF Profile S, CE, UL, FCC Certified. IP66 , IK 10 including Sensor type1/2.9-inch CMOSTotal sensor pixels3072 (H) x 1728 (V)Sensitivity Color 0.379 lx, Mono 0.042 lx, With IR 0.0 lx (Measured according to IEC 62676 Part 5)High Dynamic range120 dB WDRWDR approved & measured as per OECF analysis according to IEC 62676 Part 5, it should be more 100 dBTrue (NS)Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable) Video resolution4.1MP, 3MP, 1080P, 720P, SD, D1, VGAVideo compressionH.265 MP, H.264 MP; M-JPEGMax. frame rate1 to 20 fps (5.3 MP)1 to 25 fps (4.1 MP)IR RangeMinimum 30mIR intensityAdjustableLens typeAutomatic Varifocal 3.2 to 10 mmLens adjustmentMotorized zoom/focusDetection Range of ObjectsUp to 141m (463ft) as per EN-62676-4Audio communicationTwo-way, full duplexAudio Line In/Out 1/1 Alarm In/Out 1/1 Ethernet10/100 Base-T, auto-sensing, half/full duplex Ethernet connector10/100 Base-T, auto-sensing, half/full duplexRJ45ConnectivityONVIF Profile S, ONVIF Profile G & ONVIF Profile TAnalysis TypeEdge Based AnalyticsAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimationOther functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotMin. 512 GB supportSD card health monitoringExtreme lifetime and health monitoring support that provides early service indicationProtocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationMTBF calculation of used componentBased on: Siemens SN 29500, or FIT figures manufacturer. Theoretical MTBF is about 320000 hours.EncryptionTLS1.0/1.2, AES128, AES256Data Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patchesHardware for data security Unique Crypto-processor / TPMDual Power Supply for redundancyPOE and 12VDC simultaneouslyOperating temperature-30 ºC to +50 ºC (-22 ºF to +122 ºF)Humidityup to 90% relative humidity (non condensing)Ingress protectionIP66Impact protectionIK10Certifications: CE, FCC, UL, VCCI, BIS including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of Outdoor IR HD PTZ Camera with 1/2" progressive scan Exmor CMOS, Effective pixels 2560 x 1440, 30x Optical Zoom 6.6mm - 198 mm;°, 16X Digital Zoom, Minimum Illumination- Sense up on- Color: 0.05 lux , B/W: 0.01 lux, With infrared (IR) 0 lux, WDR 130dB, Video Analysis ( Object removal , Loitering , Enter or Exit from the Field , Object Classification etc.) Intelligent Dynamic Noise Reduction, BLC, White Balance, Mechanical switchable IR filter, Pan Range 360° continuous, Tilt Range 0°–90°, Pan/Tilt Modes - Pan: 0.1°/s - 240°/s; Tilt: 0.1°/s - 120°/s, Presets 256 , Tours, IR distance 300 mtrs, IR can be internal or external with full 360 deg PAN coverage; White Led 60m; Audio- 1/1 Channel In/Out, Memory card slot (support upto 1TB) , 24 individually configurable privacy masks, Simple single cable installation with POE+ support for Outdoor application, wiper, Defog, IP66 , ONVIF Profiles S & G, CE, UL Certified.including Sensor type1/2-inch CMOSTotal sensor pixels2688 x 1520 (4 MP)Sensitivity 0.02 lux, Mono, 0.002 luxHigh Dynamic Range 130 db or betterTrue Day/NightAuto, Color, MonochromeNoise reductioniDNR / 3DNR with separate temporal and spatial adjustmentsIntelligent defogIntelligent Defog automatically adjusts parameters for best picture in foggy or misty scenes (switchable)Shutter Speed Video (NS)resolution1440p, 1080P, 720P, D1No. of StreamsMultiple configuration streamsVideo compressionH.265 MP, H.264, M-JPEGMax. frame rate60 fpsOptical and Digital zoom30x Optical 16X digitalLens type30x motorized zoom │ 6.6 mm - 198 mm (F1.5 – F4.8)White LEDRequire white LEDs to see Images in color upto 60 Mtr in no Ambient lightIR Range320 Mtr or betterLens adjustmentMotorized zoom/focusTilt angle -90° to 0° (Auto-flip 180°)Pan angle 360 º ContinuousPre set Position256Guard Tour2 ( Maximum Total duration of 15 minutes for each Tour) and 2 Pre position tour.Sector/Blanking16 Independent sectors with 20 characters on each titlePre position speed Pan : 240 º/s , Tilt : 100 º/sAudio communicationTwo-way, full duplexAudio Line In/Out 1/1Alarm In/Out 1/2Ethernet10/100 Base-T, auto-sensing, half/full duplexEthernet connectorRJ45ConnectivityONVIF Profile S, ONVIF Profile G Analysis TypeEdge Based AnalyticsAlarm rulesRule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation. Object filters:- Colour , Speed , directionOther functionsSharpness, Backlight compensation, Contrast enhancement, Display stamping (Name/logo/Time), Pixel counterMemory card slotMin. 512 GB supportSD card health monitoringSD card health monitoring Protocols:IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/ RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II),802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authenticationEncryptionTLS1.0/1.2, AES128, AES256Data Security:· Secured connections supported (HTTPS)· Password enforcement at initial set up· Execution of 3rd party software is disabled· Firmware updates via OEM digitally signed firmware files only· Detect changes in a configuration· Support of customer specific certificates· Support of Microsoft Active Directory for safe management of user access rights· Regular updates via security patchesHardware for data security Unique Crypto-processor / TPMDual Power Supply for redundancyPOE+( IEEE802.3bt) and 24VACOperating temperature-40 ºC to +60 ºC (-40 ºF to +140 ºF)Humidity 0 to 90% ( NON condensing)Ingress protectionIP 66IK Rating IK10WiperRequire rain sensing Wiper.Privacy Masking32 Individual configurableCertifications: CE, FCC, UL, VCCI, BIS including all petty material required to complete the job upto entire satisfaction of EIC Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of 20 MP Multi sensor camera with 4x 1/2.7‑inch CMOS sensor, Effective Pixel : 4x 2592 (H) x 1944 (V). Sensitivity(Measured according to IEC 62676 Part 5) : Color : 0.1 lx Mono 0.01 lx. 100 dB WDR, IR 30 Mtrs 360⁰, Lens 3.7 - 7.7 mm; Motorized zoom and focus, Max Resolution 4x 2592 (H) x 1944 (V)@30 fps. Intelligent Video Analytics with minimum 4 analytics run simultaneously (Any object, Object in field, Line crossing, Enter / leave field, Loitering, Follow route, Idle / removed object, Counting, Occupancy, Crowd detection, Condition change, Similarity search, Flow / counter flow), Camera Trainer. integrated microphone; Alarm in/out; One IP address for all four imagers; Secure Element (“TPM”): RSA 4096 bit, AES/CBC 256 bit; PKI X.509 certificates; Simple single cable installation; ONVIF Profiles S & G, CE, UL Certified.including all petty material required to complete the job upto entire satisfaction of EIC (NS) Makes :- AXIS / Mobotics/ Bosch / Avigilion

SITC of IP storage solution with 16 TB , with RAID-5/RAID-6 protected, Dedicated storage operating system delivers robust , secure operation, Hot-swappable hard drives, Advanced user and alarm management,Intel® Xeon® E-2226GE (12 MB Intel Smart Cache, 3.4GHz) Processor, 16 GB DDR4-2666 2Rx8 ECC UDIMM memory installed, 2U/3U rack mount, 8 Trays: 3.5-inch SATA 3; max 12TB per HDD slot maximum supported, 12Gb/s SAS RAID Card, 6 USB ports; Intel onboard graphics (Three digital outputs), Windows Server IOT 2019 for storage standard (64-bit),UL, CE Certified. 2 x RJ45 Gigabit Ethernet LAN ports (teamed); 1 IPMI BMC port. Operating temperature (°C) 10 - 35°C; Operating relative humidity, noncondensing (%) 8 - 90%.including all petty material required to complete the job upto entire satisfaction of EIC (NS) Makes :- AXIS / Mobotics/ Bosch / Avigilion

Supply, Installation, Testing & Commissioning of Monitoring Software Client along with Workstation PC with PROCESSOR Intel i CORE i7- 11th generation Processor, FSB SPEED 1333 MHz, OPERATING SYSTEM Windows 10 Professional (64-bit), CHIPSET Intel Q67 Express or Better (4x2GB) RAM dual Ethernet port, HD Graphics Card with dual monitor support with 21" LED Monitor complete in all respects etc. as reqd.including all petty material required to complete the job upto entire satisfaction of EIC (NS) Makes :- HP / Dell / lenovo/ IBM / Fujitsu

Supply, Installation, Testing & Commissioning of Full HD, High Resolution 46 - 48 inch LFD professional display panel with brightness 500 nits or better; Resolution 1920 x 1080; with on screen adjustment menu, with wall mount kit complete in all respects etc. as reqd.including all petty material required to complete the job upto entire satisfaction of EIC (NS) Makes :- Samsung / LG / Panasonic/ Sharp / NEC

Supply, installation, testing & commissioning of 27U suitable MS Rack having facility to accommodate control equipment as mentioned above including all petty material required to complete the job upto entire satisfaction of EIC. (NS)

Supply and Laying of 2x1.5 sq mm FRLS Power Cable in the existing surface casing & capping as required. including all petty material required to complete the job upto entire satisfaction of EIC (NS)

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. including all petty material required to complete the job upto entire satisfaction of EIC (NS) (a) 25 mm

Supply, Installation, Testing & Commissioning of 6U Rack with all Accessories., as per specs complete etc. As required.including all petty material required to complete the job upto entire satisfaction of EIC (NS)

Supply, Installation, Testing & Commissioning of Category 6A field termination plug designed to support 10 Gigabit networks that can be easily terminated using parallel jaw pliers. The IDC is designed to accommodate different diameter conductors from 22 AWG-26 AWG Solid Wire. The Field Terminable Plug should be downward compatible to Cat 5e/6 and must meet IEC 60603-7-5 and must be UL Listed. plug protection: IP 20 Field Termination plug: TIA-568-C.2 CAT 6A Supporting cable diameter: 6~9 mm Plug Housing: Zinc alloy current rating: 1.5 A Dielectric withstanding voltage: 1000V DC Insulation resistance: 500M Ω MIN. Contact resistance: 20m Ω MAXincluding all petty material required to complete the job upto entire satisfaction of EIC (NS) Make: Belden/Panduit/Molex/Siemon

Supply, Installation, Testing & Commissioning of CAT 6A Cable which is specifically designed to support high speed data network applications such as 10-Gigabit Ethernet (10GBASE-T). Cable should have constructed of 4 screened pairs and a drain wire. This cable minimizes alien crosstalk, provides excellent signal isolation and provides superior electromagnetic interference (EMI) protection. Enhanced performance 4 pair U/FTP LS0H cable Applications: Category 6A U/FTP Cable is intended for high speed data applications up to 500MHz including: IEEE 802.3bt (POE++) IEEE 802.3 10GBASE-T 10Gb/s IEEE 802.3 1000BASE-T 1Gb/s UL Listed Electrical/Optical Characteristics: Power: 96watt Capacitance: 40 pF/m nom. @1 KHz. DC Resistance: 72 Ω/Km max complies to ROHSincluding all petty material required to complete the job upto entire satisfaction of EIC Make: Belden/Panduit/Molex/Siemon (NS)

Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord 1 mtr. Cable conductor Size: 24-26AWG Stranded bare copper with Pre Terminated with RJ 45 Plug. Screen materials Aluminum/polyester shield with tinned copper drain wire. Operating life: 750 insertion cycles RJ45 plug material: Clear polycarbonate (PC) Boot material: Clear polyvinylchloride (PVC) Contact material: 0.35mm thick copper Contact plating: 1.27um gold RJ45 plug dimensions compliant with: ISO/IEC 60603-7 and FCC 47 Part 68 Temperature -20°C to +60°C RJ45 Plug imensions compliant with ISO/IEC 60603-7 and FCC 47 Part 68 Fire Propagation Tests: IEC 60332-1, IEC 61034-2 Electrical Characteristics: Max Voltage: 150 VAC (max), Max Current: 1.5A @ 25°C; RoHS Compliant; UL Listed including all petty material required to complete the job upto entire satisfaction of EIC (NS) Make: Belden/Panduit/Molex/Siemon

Supply, Installation, Testing & Commissioning of CAT 6A S/FTP Patch Cord 5 mtr. Cable conductor Size: 24-26AWG Stranded bare copper with Pre Terminated with RJ 45 Plug. Screen materials Aluminum/polyester shield with tinned copper drain wire. Operating life: 750 insertion cycles RJ45 plug material: Clear polycarbonate (PC) Boot material: Clear polyvinylchloride (PVC) Contact material: 0.35mm thick copper Contact plating: 1.27um gold RJ45 plug dimensions compliant with: ISO/IEC 60603-7 and FCC 47 Part 68 Temperature -20°C to +60°C RJ45 Plug dimensions compliant with ISO/IEC 60603-7 and FCC 47 Part 68 Fire Propagation Tests: IEC 60332-1, IEC 61034-2 Electrical Characteristics: Max Voltage: 150 VAC (max), Max Current: 1.5A @ 25°C RoHS Compliant UL Listed including all petty material required to complete the job upto entire satisfaction of EIC (NS) Make: Belden/Panduit/Molex/Siemon

Supply, installation, testing and commissioning of Wall Mountable with 12 mid/high drivers in an articulated array for wide dispersion. The louspeaker shall meet the following performance criteria: Usable Frequncy Range (-10 dB) of 100Hz - 16 kHz. Long term power handling of 200 Watts. The Loudspeaker shall have a Max. SPL (Peak) of >=119 dB with a norminal dispersion of 145° H x 20° V. The loudspeaker system shall be comprised of a Powder-coated steel grille; Twelve 2.25-inch or better mid/high frequency drivers and and a norminal impedence of 8 ohms. Optional 70/100V OEM transformer module with tap settings of 100/50W or better shall shall be available.including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Bose, EAW, Martin Audio/ELECTROVOICE

Supply, installation, testing and commissioning of OEM Pan/tilt bracket for FOH Column array loudspeaker including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Bose, EAW, Martin Audio/ELECTROVOICE

SITC of Fully Digital Central Conference Controller Unit, Can be control and power at least 100 units or better, this shall be possible by Serval Unit as a Master /Slave/Power supply unit ,Must have LCD/OLED display to allow easy access to all the participants with neccesary controls and configures of system , number of Open Microphone 6 or Better, External Ports for Camera Tracking RS232/RJ45/D9, Daisy Chain Connetivity through CAT 6 Shielded Cable /Multicore Cable ,Microphone Modes VOX,FIFO, Request including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Brahler, Beyerdynamic, Bosch

SITC of Conferencing Delegate unit in Under Table box form factor, can be used as chairman or delegate microphone unit, unit should have Phoenix® connectors for buttons, microphone, headphone and loudspeaker, Should have Two RJ45 sockets to connect the system unit to the control unit or another microphone unit/system unit. Shall Include Bicolor Piezo table mounted Button including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Brahler, Beyerdynamic, Bosch

SITC of Conferencing Chairman unit in Under Table box form factor, can be used as chairman or delegate microphone unit, unit should have Phoenix® connectors for buttons, microphone, headphone and loudspeaker, Should have Two RJ45 sockets to connect the system unit to the control unit or another microphone unit/system unit. Shall Include Function and Clear Piezo table mounted Buttons including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Brahler, Beyerdynamic, Bosch

SITC of Conferencing Chairman/Delegate unit in Under Table box form factor, can be used as chairman or delegate microphone unit, unit should have Phoenix® connectors for buttons, microphone, headphone and loudspeaker, Should have Two RJ45 sockets to connect the system unit to the control unit or another microphone unit/system unit. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make : Brahler, Beyerdynamic, Bosch

SITC of wireless handheld microphone with (UHF) Diversity receiver ,12 Channel Preset or better , Display on Transmitter and Receiver , RF Power output 50mW or Better , Polar Pattern :- Cardioid , Carrier frequency range 500Mhz to 865Mhz , Frequency response 45–15kHz, Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Transmitter , Receiver dynamic range 106 dB (A-weighted) Or better, switching bandwidth Minimum 40 Mhz Or better.including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Sennheiser, Beyerdynamic, Shure

SITC of 98" LCD touch panel with 3840 X 2160 resolution or better, USB playback,,4X HDMI 2.0, brightness 500 nits or better, Video wall mode should be available, 10 point touch, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Christie, Barco, NEC,samsung

SITC of 55" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Christie, Barco, NEC,samsung

Supply, Installation, Testing & Commissioning of Full HD, High Resolution 46 - 48 inch LFD professional display panel with brightness 500 nits or better; Resolution 1920 x 1080; with on screen adjustment menu, with wall mount kit complete in all respects etc. as reqd.including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Makes :- Samsung / LG / Panasonic

SITC of Video Conferencing system with 12x eagle eye came , with extender , to place codec in rack & Camera below the 98 inch display.HD Video Conference system with full funcitons wireless remote and Omni directional Boundary layer microphone and two Full HD PTZ Camera and related acessories etc as required Complete system with ESSENTIAL softwear MCU (1+5)system having following features and specifications including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Polycom, Cisco

Sleek rectangular Cable access enclosure for AV connectivity and 1x Multi-Region AC power, 2 x USB Outlets for charging Mobile devices, pass through holes for 1USB charging, 1x HDMI, 1x LAN & VGA and 6 nos. of Connecting cable, RJ45 connectors, length 2.5 m (8 ft.) 1 no. of Connecting cable, RJ45 connectors, length 20 m (65 ft.). including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Kramer/LOGIC

MultiFormat twisted Pair Transmitter having auto switching between inputs, Inputs: 1 USB C/Display Port, 1 HDMI, 1 VGA , Audio Input: 1 analog audio, Resolution: Up to 4K (4096x2160) @ 30 Hz or more, Data Rate: 10.2 Gbps, Signal transmission distance: Minimum 70 m using shielded twisted pair cable for audio, video, controls & power. Output: Twisted Pair/ HD BaseT output on RJ 45 port, HDCP & EDID Management. Shall be supplied with under table mounting accessories. including all petty material required to complete the job upto entire satisfaction of EIC. Make Extron/Kramer/LIGHTWARE (NS)

Supply, Installation testing & commissioning of HDMI over twisted pair Transmitter having 1 x HDMI input along with audio port; 1 x Twisted pair output; Ccontrol port : RS-232 & IR; Supports computer and video resolutions up to 4K; Transmission range : 70 meter; HDCP 2.3 compliant.Data Rate: 10.2 Gbps. Shall meet Regulatory compliance c-UL, CE, UL. Shall support local and remote power.including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Kramer/LIGHTWARE

Supply, Installation testing & commissioning of HDMI over twisted pair Receiver having 1 x HDMI output along with audio port; 1 x Twisted pair Input; Control port : RS-232 & IR; Supports computer and video resolutions up to 4K; Transmission range : 70 meter; HDCP 2.3 compliant. Data Rate: 10.2 Gbps. Shall meet Regulatory compliance c-UL, CE, UL. Shall support local and remote power. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Kramer/LIGHTWARE

Supply, Installation testing & commissioning of Presentation 8x4 Matrix Switcher having six HDMI input, two twisted pair input; two Twisted pair output and Two HDMI mirror output,; Max resolution upto 4K; Max video data rate : 10.2 Gbps. Scaling shall be provided on twisted pair outputs. Shall have built in AV control processor with 2 x bidirectional RS‑232 ports; 1 x bidirectional RS‑232/RS‑422/RS‑485 port; 2 x IR/Serial ports for one-way control; 4 x relays; 4 x Digital I/O ports. Shall have min 2x 10/100/1000 BaseT ethernet port and shall be able to control min 30 devices over ethernet. SDRAM: 512MB, Flash memory: 4.5 GB. 2 or more analog audio output. Shall meet regulatory compliance as CE,c-UL, UL. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Kramer/Lightware

Wireless presentation system with 4 feed simultaneous output,Resolution : 4K/UHD @ 60. Input: 1x HDMI, Output: 1x HDMI. Data Rate: 18 Gbps. Should provide full screen mirroring. Content sharing through software/app or dongle. Shall support iOS 12 and later, Android 9 and later, macOS 10.14 or later, Windows 10, Built in Audio De-embedding on 1x analog stereo, balanced/unbalanced. Shall suport Dual network to provide separate network access for Guest laptop connectivity. Shall have built-in /External Wireless access point. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Kramer/AMX

SITC of 8 Port Full Duplex 10/100/1000Mbps Auto-Negotiation RJ45 network switch, Fanless architecture, Standards and Protocols IEEE 802.3 / 802.3u / 802.3ab/ 802.3x /802.1p to be supplied along with Built-in or external power supply. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make CISCO/COMSCOPE/EXTREME

SITC of Wireless access point 802.11 b/g/n and dual band support. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make CISCO/COMSCOPE/EXTREME

SITC of 6' (1.8 m) HDMI male(M) to HDMI Male (M) Cable with 28 AWG copper wire construction, resolution support of 4K/UHD @ 60 Hz, 4:4:4 or better, Gold plated connectorsincluding all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Belden/kramer

SITC of Flexible Male to Male 15-pin HD VGA cable with Audio (06 feet) for transmission of VGA video and analog audio signals. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Belden/kramer

SITC of 6' (1.8 m) USB C(M) to Display Port (M) Cable with 28 AWG copper wire construction, resolution support of 4K/UHD @ 60 Hz, 4:4:4 or better, Gold plated connectors including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Belden/kramer

SITC of other cables, connectors, convertors , 24 AWG Shielded Twisted Pair Cable with SF/UTP construction and certified for minimum 450 MHz bandwidth at distance of 100 m , Shielded RJ45 connector for Shielded twisted pair cables , of 22 U Equipment Rack, Locakable front glass door, cooling facility, internal wiring, front glass door, heat dessipation fans, movement wheels, power distribution units & equipment shelves as required, fully welded construction for strength. Extra-wide rackrail for cable pass-throughs to facilitate front-to-rear cablin. , 2 core Speaker cable - 14AWG or better, ROHS.etc as required for complete installation, programming & comissioning of the system. including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make Extron/Belden/Kramer/ neutrick

Supply, Installation, Testing and Commissioning of addressable Digital fire alarm control panel. Controller shall be 960 character/7inch color touch screen display, inbuilt networking port (both RS 485 & Ethernet), Serial port for printer with 6000 history event. The Panel shall be modular, decentralized, with redundancy in Power Supply with full functionality, Bidder not having redundancy shall supply 2 panels to comply. The panel shall be capable of providing BACnet/MODbus protocol for integration with BMS system. The number of loops should be calculated to accomodate all detector and devices with 20% spare. Panel shall have battery backup of 24 hour in standby and 30 minute in alarm condition. The Panel shall be VDS/EN 54/UL approved. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) ( NS ) 3 Loops Panel (NS)

Supply, Installation, Testing and Commissioning Active Repeater Panel. Controller shall be 960 character/ 7 inch color touch screen display, inbuilt networking port(both RS485&Ethernet),Serial port for printer. The Repeater Panel shall allow users to acknowledge, reset,silence, program, view hisory events...etc (All functions similar to main panel). The user interface of the repeater panel shall be same as the Main Controller. The Panel shall be VDS/EN 54 approved. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

SITC of Intelligent Addressable Multicriteria detector works based on Dual-Ray technology with an infrared and a blue LED so that lightest smoke is detected fast and reliable along with a heat sensor including mounting base. (Detector should comply to Test Fire 1). Detetctor should have inbuilt isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/ certification.(Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector) EN54 / Vds/UL Certification Make :- BOSCH / NOTIFIER / NOHIMI / AUTRONICA (NS)

Supply, Installation, Testing and Commissioning of intelligent addressable Heat detector. Detetctor should have inbuilt isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Shall be EN54/ VDs/ UL certification. (Detectors without Inbuilt Isolators may be considered with an additional Isolator Module per detector) (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply, Installation, Testing and Commissioning of Addressable Control Relay Module with inbuilt isolators as per NFPA 72 style 7 wiring requirements & with flexible network structures with a maximun switching current of 1A @ 30V DC. Shall be EN54/ Vds Certification/UL. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply, Installation, Testing and Commissioning of Addressable Module with one input & one output contacts, with inbuilt isolators, monitoring of a line with EOL resistor, Potential free contact monitoring. Shall be EN54 / Vds/UL Certification. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply, Installation, Testing & Commissioning of Response Indicator with matching screws complete with GI Junction box, Cable lugs at cable end and ferruling. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply, Installation, Testing and Commissioning of addessable manual break glass unit (Double action) with inbuilt isolators as per NFPA 72 style 7 wiring requirements, with flexible network structures & necessary fixing arrangements with key complete as required. Shall be EN 54 / Vds/UL Certification. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply of Addresable Loop Powered Voice Sounder with 4 different voice messages in 7 languages and 32 different tones including the cost of mounting as per specification. Complete as required. (In case of separately powered sounders, cost of the power cable, Supervised Power Supply and interface module shall be inclusive in the cost of sounders itself and shall not be paid separately and power of sounders shall be fed from main Fire Alarm Panel only) (NS)

Supply, Installation, Testing and Commissioning of Stand alone Loop Powered Strobe with inbuilt isolators as per NFPA 72 style 7 wiring requirements, should be programmed from the panel. Shall be EN54 / Vds/UL Certification. (Makes: BOSCH, NOTIFIER, NOHIMI, AUTRONICA) (NS)

Supply, Installation, Testing and Commissioning of 2CORE 1.5 SQMM COPPER FLEXIBLE sheathed CABLE FRLS FOR FIRE ALARM CABLE with termination complete in all respect. (NS) Make :- RR , Havells , Finolex

SITC of indoor AP controler less with dual-band 802.11abgn/ac/ax Wireless Access Point with Multi-Gigabit Ethernet backhaul and onboard BLE/ZIgbee, 2x2:2 streams (2.4GHz/5GHz) OFDMA, MU-MIMO, BeamFlex+, dual ports, 802.3at PoE support. includeing power adapter or PoE injector. Includes REMOTE SUPPORT, 24P ,48, 48P, 48PF, C12P, C10ZP & -24F 3 YR including all petty material required to complete the job upto entire satisfaction of EIC. including Architecture WLAN Controller should be controller less solution. Scalability Any type of controller quoted by bidder shall be capable of supporting minimum of 20 AP's from day one and scalable to 128 AP's for future requirements. High Availability High availability should be provided for controllers. In the event of a failure of the AP secondary AP shall automatically take over. WLAN Features Should support Band Steering feature that forces the dual-band capable clients to the 5 GHz band on dual-band access points. Should have Band balancing to balance the client load on radios by distributing clients between the 2.4 GHz and 5 GHz radios. Controller should involve only in management of Wi-Fi network without aggregating/routing all of Wi-Fi user traffic. Should support intelligent edge architecture for Wi-Fi access. Wi-Fi should be functional on the device if the link between AP and management controller or the controller itself goes down Should balance wireless clients across APs on different channels, based upon the client load on the APs. Should support internal DHCP server. Should support IEEE 802.11r Fast BSS Transition and IEEE 802.11 802.11k Radio Resource Management neighbour reports. Should support Client load balancing to improve WLAN performance by helping to spread the client load between nearby access points. Network Policy Features WLAN solution should be able to create access policies in order to allow or block packets for inbound traffic/outbound traffic. (NS) WLAN solution (either integrated or through external firewall) shall provide URL Filtering to block unwanted site. WLAN solution (either integrated or through external firewall) shall provide unique pre-shared keys to each and every user in single SSID. WLAN solution (either integrated or through external firewall) shall have a capacity to inspect all traffic from each wireless client and allow or deny any traffic that does not satisfy specified policies. WLAN Security Should support WPA2,WPA3 and OWE, 802.1X authentication. Should prevent users connecting to rogue AP and also prevent an outside user trying to connect to campus WLAN. Should protect Wireless network from Denial of Service (DoS) attacks and Intrusion attempts. Should be able to temporary block wireless clients with repeated authentication failures for configurable timers. Controller less access point Should support L2 Client Isolation so User cannot access each other’s devices. Isolation should have option to apply on AP or SSID's. Should support Gateway mode with NAT and DHCP services Guest and BYOD The Controller less access point should provide a Guest Login portal to authenticate users that are not part of the organization. The solution should be able to provide a web-based application that allows non-technical staff to create Guest accounts with validity for fixed duration like hours or days. System should be able to send Email notification when Rogue AP is identified. System should support internal and External Database for user authentication. The Controller should support WLAN that will allow users to login through social media like Facebook, LinkedIn, Google/Google+ or Microsoft. Management WLAN Solution should manageablyuse SNMP, CLI, GUI and Mobile app Solution should be able to receive commands from Amazon Alexa using skills. The controller should be able to present a dashboard with information on the status of the WLAN network and internet connectivity. Product The APs should support the IEEE 802/11a/b/g/n/ac/ax with dual radio capabilities conforming to Wi-Fi 6 standard. The AP should support 2x2:2 MIMO on both the bands. It should support minimum 1200 Mbps data rates on 5 GHz and minimum 570 Mbps data rates on 2.4GHz. The AP should provide an antenna gain of minimum 3dBi on both the bands. The AP should have the capability to support minimum 16 BSSID Should be WI-FI certified and WPC approved. Operating Temperature: 0ºC to 50ºC. Operating Humidity: up to 95% non-condensing Should support 500or more clients per AP. The AP should provide minimum Tx Power of 22dBm on both the bands The AP should have an option to be powered up through DC power in addition to POE. The AP should have a receive sensitivity of -96dBm. Make- CISCO/COMSCOPE/EXTREME

SITC of DAC cable with 10GBASE-LR, SFPP SMF (LC), for up to 10km over SMF, standard temperature (0°C to 70°C) including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make- CISCO/COMSCOPE/EXTREME

SITC OF Transcevier with 10GbE Direct Attach SFP+ to SFP+ Active copper cable, 1 m including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make- CISCO/COMSCOPE/EXTREME

SITC of RJ 45 IO , complete with wall plate & in wall box, with termination of LAN cable , for the pc, laptop , printers , location including all petty material required to complete the job upto entire satisfaction of EIC. (NS)

SITC & laying of Cat-6 cable complete with connector including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make- BELD EN/DLINK/KRAMER

SITC of PVC conduit pipe 25mm dia ( medium ) including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make :- Polypack , Diplast , Ravindra

SITC of 12 Core OFC cable in ground with 50/63 mm HDPE pipe with connection , termination , splashing of cable complete accessories including all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make :- DELTON /MOLEX/RR

Trenchless boring for Ofc cable 12 core for 50/63 hdpe pipe complete including all petty material required to complete the job upto entire satisfaction of EIC.( excluding cost of HDPE Pipe ) (NS)

S.I.T.C. of Solar PV Poly- Crystalline Modules of 335Wp Capacity having Anti-PID IP67 rating, average ≤ 0.75% Annual degradation of Modules, 10 years product manufacture warranty and 25 years Linear Power warranty including the cost of all petty material required to complete the job upto entire satisfaction of EIC. (NS) Make: Waaree/ Vikram/ Adani

S.I.T.C. of Module Mounting Structures (Hot Dip Galavanised) having 5 yrs system warranty and the Structure Tilt: 10- 12 degrees, Suitable to windstand wind speed of 150Km/hr including the cost of all other petty material required to complete the job upto the entire satisfaction of EIC. Note: The minimum height of inclined Panel will be 9’ clear from the finished floor level. (NS) Make: Jindal Hisar/ Hindalco/ Sail

P/F of Civil Pedestals of suitable size & height to accommodate the module mounting structures to house the solar PV Modules with M-20 grade (NS)

S.I.T.C. of String Inverter - 20 KWp + Remote Monitoring +Surge Protection Device on both AC &DC side having 5 yrs. Warranty, inverter stub with outdoor mounting and all other petty material required to complete the job upto the entire satisfaction of EIC. (NS) Make: ABB/ Hitachi/SMA

S.I.T.C. of Lightning protection system based on proactive Early Streamer Emission(ESE) technology confirming to NFC 17-102 and UNE 21186 Standards. Non-electronics based device shall emit electromagnetic impulse in the form of a streamer into the air microseconds earlier than naturally. Device confirming to NFC17-102 standards. The device mounted at least 5 meter clear to the highest point on the rooftop, Covering Radius -107 meter. Make: JMV (NS)

S/E of Earthing -AC & DC System Maintenance Free Earthing of Copper bonded having 10 ft. length, 50 mm dia. earth electrode. The electrode will be surrounded with 25Kgs of environment friendly backfill compound duly certified by ROHS as safe for environment with pits. (NS) Suitable for ESE Lightening Arrester & Solar Plant both.

S/E of DC Solar Cable Single Core 6 sq. mm -1500 V non-flammable, UV resistant, Pure copper, tin coated with double insulation 120˚ operating temp. including termination & testing and cost of other petty material required to complete the job done upto the entire satisfaction of EIC. (NS) Make: LAPP/LS/Siechem

S/E of AC Cable – 35 sq mm 4 core Al Armoured including crimping & thimbles laid loose including termination & testing and cost of other petty material required to complete the job done upto the entire satisfaction of EIC. (NS) Make: LAPP/LS/Siechem

S/E of DCDB & ACDC having IP 66 protection Outdoor junction boxes with standard make switchgears and fuses and all other petty material required to complete the job upto entire satisfaction of EIC. (NS) Make: L&T/ABB/Schneider

P/F of GI Strip (25x3) including clamping, termination & testing charges with all petty material required to complete the job upto entire satisfaction of EIC. (NS)

S/E of MC4 Connector of reputed make including 5 years warranty and the cost of other petty material required to complete the job upto the entire satisfaction of EIC. (NS)

Devendra K Sharma and Associates