SPECIAL REPAIR TO FOL STORE BLDG NO T-79 OF ASC SUP TYPE C AND PROVISION OF VEHICLE WASHING PLATFORM AT MT SECTION OF STATIC WORKSHOP UNDER THE AOR OF GE DEVLALI

Amount

Dismantling of Single layer Mangalore pattern or similar tiles in roofing complete all as specified and directed.

Dismantling of battens for tiles, shingles etc, of any size including tiling fillets exc 15 cm complete all as specified and directed.

S&F Steel work in tubular/Hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S. 1161-1979 grade St. - 240. complete all as specified and directed.

Dismantling of timber scantling framed work 40sqcm and over in section in any position all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws all as specified and directed.

M & L for two coats of synthetic enamel paint of new steel surfaces over a coat of priming with red oxide incl. preparation of new surfaces all as specified and directed.

Demolition of Brick work or stone/boulder masonary, laid in cement mortar or cement lime mortar all as specified and directed.

M&L brick work with flyash bricks, straight or curved on plan n.exc 6m mean radius in cm 1:6 all as specified and directed.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:6 finished even and smooth ( without using extra cement ) with sagol finish all as specified and directed.

Taking down cement mortar plastering on brick or stone walls, etc. including raking out joints,hacking for key,scrubbing down with water, etc all as specified and directed.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement mortar 1:4 finished even and smooth ( without using extra cement ) all as specified and directed.

M & L preparing plastered or unplastered new surfaces applying three coats of White wash on new wall plastered surfaces.

M & L preparing plastered or unplastered new surfaces and applying two coats of cement base paint over a coat of cement primer on new wall plastered surfaces.

M&L for preparing old decorative plastered/ unplatered surface of walls by removal of existing treatment washing down and applying three coats of White wash all as specified and directed.

Demolition of concrete in ground floors & paving not exc 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any guage thicness including Nainital or similar pattern roof covering.

S&F 0.80mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and directed.

S & F MS flat as in wind ties incl all cutting , bending drilling etc. complete conforming to Fe- 410 'O' or Fe- 310'O'

M & L for 75 mm thick Cement concrete type C-2, 1:3:6 (40 mm graded aggregate ) as in Plinth protection/ floor all as specified and directed.

M & L for cement concrete Type E2 1:5:10 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L 75mm thick PCC (1:2:4) type B1, (using 20 mm graded stone aggregate in floors) finished even and smooth with using extra cement complete all as specified and directed.

M & L For Glass dividing strips,3mm thick and ditto and inserted in position to confirm to design complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping/hold fast bed blocks,bed plates,roof kerbs or mud stops, rounded or chamfered on edges or similar items including necessary form work stops moulds etc all as specified and directed

Taking down chowkat or frame with shutters (with out taking off shutter from the frame ) not exceeding 1.5 Sqm each as directed by Engineer-in-Charge.

S&F Steel ventilator with top hung shutter hinges , and steel peg stay, complete all as specified and directed

All as per Srl item No. 28 here in before but without glazing bars all as specified and directed

S&F mild steel framed work such as grills, gratings, etc with ends of bars, shouldered and /or riveted, or forged into spicks, framed guard bars, ladders, framed balusters, walk ways, railings, framework of water tankd and similar work conforming to Fe 410-O all as specified and directed.

S&F in repair 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square in exc 0.5 sq.m in each pane

S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples Complete as in repairs all as specified and directed.

Demolition & breaking up of 150 mm dia of drain pipe (salt glazed stone ware AC or reinforced concrete) set in cement mortar.

S&F 110mm bore PVC(SWR) pipes single socketed in any length wilth rubber ring joints laid in floor or on walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any raidus

Taking down chowkats or frames exc.1.5 sq.m but not exc. 4 sq.m each but with shutters ( without taking off shutters from the frame ) complete all as specified and directed.

Supplied and fixed mild steel framed work as in doors or gates of angle or other section with gusset Plate, rails,braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges and door fittings necessary rivetting/welding cutting up complete steel conf. to Fe-410-0 or Fe-310-0 all as specified and directed. Note : Distrubed surfaces of wall shall be made good to true surface.

S&F 0.80 mm th.mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including, steel gates and similar work, cut size, holes punched; including round headed screws, and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded , including bending or turning up, mitred angles, etc. as required. complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in soft/loose soil all as specified and directed.

M&L for broken stone or boulders Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and directed.

M&L for Plain Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base of floors all as specified

M&L for Plain Cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in Coping all as specified

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft /loose soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil

Forming Contraction (Dummy) joints grade 'A' 65 mm deep x 10mm wide, filled with sealing compound grade 'A' all as specified and directed.

M&L for Plain Cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in surface channels and drains complete all as specified

Mild steel TMT bars 10 dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips.

All as per above item, but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders

M&L RCC M-25 (using 20mm garded stone agg) as in walls, retaining walls, basementof walls, ballast wals, and the like any thickness, above top of footings, including attached pillasters and buttresses all as specified and directed.

M&L RCC M-25 (using 20mm garded stone agg) as in beams and the like all as specified and directed.

M&L RCC M-25 (using 20mm garded stone agg) as in slab supported walls, beams,and columns in floors, roofs, landings, balconies, canopies, deck slab and in shelves and the like all as specified and directed. (Note for item 48 to 50 formwork and reinforcement shall be measured and paid separately)

Formwork to sides and soffits of beams, bands and the like for fair finished surfaces of concrete.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to better.

Formwork to suspended slab such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (horizontal or sloping) all as specified and directed.

Finishing surface of concrete roads, pavements by brooming all as specified and directed.

Note: Amount of sch of credit of Rs.17,900.00 will be deducted from total amount of BOQ.

M/S MANISH CONSTRUCTION CO

M/S GURBAX AND CO

JEET CONSTRUCTIONS CO.

M/S G.S RAWAL

Alpha Construction

M/S SAMEER SUBHASH PATANI