Extension of Department of Endo-Dontics and Conservative Dentistry at GDCandH Srinagar ( Civil and Mechanical Parts)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge In cement mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) From brick work in cement mortar

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) including Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level (Labour charges only)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) including Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

12mm Cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming All kinds of soil.

Providing & laying of stone soling hand packed in foundation and plinth incl ramming, watering, compaction & lead lifts all carriages upto site of work complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Providing and laying Vitrified tiles in walls with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints Size of tile 600x1200 mm by way of using tile on tile chemical

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.40 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing of pre coated G.I eaves boarding 0.5mm thick including all fittings and fixtures, all cost and carriages, scaffolding, making necessary connections with rain water pipes complete job ; all inclusive.

Providing and fixing of colour coated rain gutters 150mm wide 0.5mm thick including fixing with M.S clips and all fittings and fixtures, all cost and carriages, scaffolding, making necessary connections with rain water pipes complete job. all inclusive.

Providing and fixing coloured pre-coated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The Sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including ridges, hips and valleys of required size and thickness with all lifts, leads and carriages complete job; all inclusive

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab upto 0.5 sqm) 18 MM

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and fixing CP fittings of approved brand. Jaguar/kerovit or equivalent

Basin mixer

Wall mixer

Sink mixer

Angle valve

PVC connection (24")

PVC connection (18")

Urinal waste

PVC waste pipe flexible

sink waste

CP Grating, anti cockroach trap

Bib Cock

Towel Rod

Soap case

Health faucet

Paper holder

chain 1m long

Providing and fixing AC-3 Laminated HDF WALL panneling of standard melamine impregnated decorative film with highly resistant surface impregnated with melamine resins and aluminium oxide 08 mm thick with glueless installation technique having fire resistance ,water resistance ,and scratch resistance beneath layer of jamping with ply complete job of approved make and design by the competent authority complete job as per directions of engineer incharge all inclusive

Providing and fixing AC-5 Laminated HDF flooring of standard melamine impregnated decorative film with highly resistant surface impregnated with melamine resins and aluminium oxide 12mm thick flooring with glueless installation technique having fire resistance ,water resistance ,and scratch resistance beneath layer of 2mm thermacoal and poly ethylene sheet for moisture resistance complete job of approved make and design by the competent authority including dismantling of old and damaged flooring complete job; as directed by engineer incharge all inclusive

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitrous wash basin with C.I. brackets, with pedestal including all necessary fitting and fixtures complete job; all inclusive as per direction of Engineer Incharge

Providing , installation, commissioning and testing Hot water Geyzer of approved make including fixing with bolts/ fasteners/PVC connection etc. Venus, Recold, Hindware, Havells, Jaquar, Crompton of required capacity fittings and fixtures all complete wherever required in the course of completion. complete job. 50 liters

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x510mm bowl depth 200mm

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. including dismentaling of old WC

Engagement of labour ,plumber, helper ,carpenter, for removing old CP fittings,old steel sinks, removal of old GI pipes their cutting and refixing of the serviceable CP fittings including steel sinks for dismembering existing doors and chowkats incl. sawing and moulding them again to the required size ,also includes to resize the existing doors complete job as directed including stacking of serviceable material

Carpenter

Plumber

Labour

Helper

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 andIS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides withrequired EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)

For fixed portion Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)

For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing A.C.P 3mm multi coloured ( Fire retardant) in partitions, ceilings, shutters frames etc including cost of rubber, neoprene gasket,taping, waterproof silicon sealent ,or as required at site as per the directions of concerned engineer in charge

Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by crisscrossing GI wire. With resin bonded fiber glass wool with density 16 kg/cum

Providing and fixing of imported wallpapers (Glass cloth or Fabric type) on walls/ceiling of approved quality like cassio, passion, polo or other including cost of fixing material and labour including preparing even surface to provide smooth texture of wall paper complete job confirming to IS 15418 (2003) design approved Engineer Incharge

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1mm thick

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Dismantling of (panelling) ceiling (6-12mm) thick including underneath jambs,/supports including carriage of serveceable material outside the site of work upt 04km average Lead including loading, Unloading and disposal of inserveceable material outside the municpal limits or as per the directions of Engineer Incharge complete job all inclusive

Providing wood work in joist (Karries) including hoisitng, fixing in position and applying wood preservative on unexpossed surface etc complete job all inclusive First class KD Wood

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) :

Supply and laying of PVC medium grade Conduit to be laid on surface with screws fixed in rowel plugs complete with all allied accrues like bends, tees etc.25 / 19 mm dia for paving way of laying of wires of haeting points /circuits ,machine points /circuits and sub mains .The Job includes cutting of walls with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P.O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's and whole walls for matching of same

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and fixing of 450mm deep Cabinets/ Almirahs of 19mm plywood with shutters including 0.8mm laminated Dulmica/Sunmica on exposed surface and painting on all internal surface with back side of 6mm ply covered with Dunmica on internal surface with all necessary fittings like locks, hinges, knobs, Magnetic catchers, locks dunmica strips, screws/ nails, adhesive tower bolts handles etc complete job: all inclusive, as per direction of Engineer Inchaerge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class KD wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Imported KD Wood 30mm Thick

Providing and fixing 30mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge Imported KD Wood

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of : 12 mm thick pre-laminated particle board (decorative lamination on both sides) grade-I, medium density flat pressed three layer particle board FPT-I or graded wood particle board FPT-I, IS: 3087 marked, bonded with BWP type synthetic resin adhesive as per IS: 848 and pre-laminated conforming to IS: 12823, Grade-I, Type-II marked

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing of stainless steel hardware fittings of approved make (standard gauge) including neccesary fittings complete job.

Tower bolts 8''

Tower bolts 4''

Handle 6"

Handle 10''

Door stoper

Curtain road brackets

Curtain rod

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

Providing and fixing PPR Union 20mm

Providing and fixing ball valve of approved quality, High or low pressure, with plastic floats complete 32mm

Providing and fixing PVC pipe fittings of Prince/supreme or equivalent Type-B as per directions of EIC-:-

Plain Bend 75mm

Plain Bend 100mm

P-Trap 100mm

P-Trap 75mm

Door Tee 75mm

Door Tee 100mm

Plain Tee 75mm

Plain Tee 100mm

100mm Floor trap

Collar 100mm

Door bend 100mm

Elbow 50mm

Plain Tee 50mm

Providing & fixing PVC pipe heavy duty Type-B (prince, Finolex), Water or Vent pipe with cowl. And necessary bends , junctions, reducers, rubber washers , adhesives , complete job also including cost of all fittings and fixture like bends Tee's Collars Sockets Spigots ,reducers ,traps, washers, Earth work, Sand Cushion and Back Filling wherever required as per the direction of Engineers in charge.

50 mm diameter

75 mm diameter

100 mm diameter

Providing and fixing roller blinds on internal side of windows of approved quality and material including cost of channel buds ,threads nails ,bracket, labour and carriage upto site of work complete as directed by Engineer Incharge Complete job; all inclusive .

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing and fixing laminated translucent film of approved design ,including cost of lettering with required font,colour including imprinting of logos as approved by the concerned competent authority and fixing on the glass work including cost of labour and material complete job. all inclusive as directed by Enghineer Incharge

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Supply and installation of signage plates for rooms-meeting halls etc of size 220mm x120mm x3mm in SS304 matt finish having letters engraved in the SS plate in black vinyl steam pressed to get a clean finish and having font size of name at least 30mm, fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to the satisfaction of engineer in charge complete job; all inclusive

Carriage of materials by way of mechanical transport including loading unloading leads lifts from source to site of work complete job.

Aggregates above 40mm for an average lead of 20Kms

Sand and Aggregates below 40mm for an average lead of 20Kms

Bricks for an average lead of 25Kms

Providing and fitting of Double panel Steel panel heating Radiator of size 2400x600 cm at different locations in the Hospital. The job including providing, fitting and testing of new steel panel heating Radiator double panel of size 1800x600 cm of heat out put 2500 Kcal with working pressure ranging from 10-13 bar having working temperature at 110C complete with Top grilles and side covers as standard along with inlet valve, outlet valve air purge valve and threaded plug as per OEM Inlet water Temp 75oC outlet water Temp 65oC Room Temp 22oC

Providing and fitting of Mild Steel class “C” ERW pipes of 25mm diameters with fittings like tees, elbows, bends, junctions, unions flanges etc. The job encompasses coating the MS pipe line with two coats of primer

Providing and fitting of Mild Steel class “C” ERW pipes of 20mm diameters with fittings like tees, elbows, bends, junctions, unions flanges etc. The job encompasses coating the MS pipe line with two coats of primer

Hot water pipe insulation Puff insulation/Glass wool/Rock wool insulation along with aluminium cladding of 24 Gauge as per specifications 25mm DIA (25mm thick 750 GSM)

Providing and fixing of Ball values as per relevant IS specifications of 20mm diameter. The job includes providing and fixing of required nipples, flanges etc as shall be required at site

Fabrication and fixing of angle iron supports to be fabricated out of ISA 40x40x5mm, 50x50x6mm etc and to be filled with walls surfaces etc with dash fasteners including a coat of primer over the frames