Construction of Unity Mall PM Ekta Mall at Core Capital Area at Site 1 HEC area Ranchi Jharkhand

Amount

EARTH WORK

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra rates for quantities of works, executed : In or under water and/or liquid mud, including pumping out water as required.

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

CONCRETE WORK

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing P.C.C. M - 100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50 mm to 25 mm size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

R C C WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ).

All works upto plinth level

All works above plinth level upto floor V level

Providing P.C.C. M - 200 with nominal mix of (1:1.5:3) in foundation/ column/ beam with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plainwindow sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Roof slab

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for Each four floors or part thereof.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centring and shuttering items )

Centering and shuttering including strutting, propping etc. and removal of form for : Cornices and mouldings

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 MTR.re or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. 28mm. 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 25 mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

BRICK WORK

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Extra for brick work for each consecutive floor above first floor including watering & scaffolding all complete as per direction of E/I

WOOD WORK

Supplying, fitting and fixing good quality, well dressed and well seasoned Sal wood work in choukhat in doors, windows, skylights, fanlights and C/W celestial window openings, including wedge over all clamps complete includingapplicationof two coatsof wood preservativeof approved quality on the surface butting walls and lintels all completeas per building specificationand direction of E/I

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Providing, fitting and fixing oxidised iron fitting of approved quality and make to door and window all complete as per building specification and direction of E/I necessary screws etc. complete. 300 mm sliding door bolt

Providing and fixing matt finished Stainless Steel 100 mm Mortice latch and lock with 6 levers and a pair of lever handles of approved quality and make with necessary screws & necceasry fixtures, etc. all complete as per the direction and entire satisfaction of Engineer-in-Charge.

Providing and fixing matt finished Stainless Steel 100 mm Mortice latch and lock with 6 levers and a pair of lever handles of approved quality and make with necessary screws & necceasry fixtures, etc. all complete as per the direction and entire satisfaction of Engineer-in-Charge.

Providing & fixing Floor patch lock of approved make & design.all complete as per building specification and direction of E/l.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634- 1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge

FreColor Toilet Cubicales System Model Type-ZMS Nylon Series Thicness of Compact Laminate : 12mm Rate as per Drawing Color of HPL Board: Single Color Size of Cubical: As per Drawing (W)& (D) X 2003 (H) Door Size: 1750mm(H)X 610mm (W) Overall Ht. of Cubical : 2003mm (Including Bottom Gap of 150mm) Accessories: Standerd- Merino Make Aluminium, Nylon Polymide 6 Accessories) (a) Aluminium "U" Chanel (b) Aluminium "F" Chanel (c) Aluminium Door Stopper Channel (d) Aluminium Top Rail (e) Nylon Coat Hook (f) Nylon Privacy Thumb Turn C/W Occupancy Indicator (g) Nylon Door Knob (h) Nylon Hinges-Gravity to Close (i) Nylon Adjustable Foot (j)Rubber Door Stopper Lining (k)S S Screw 304G & PVC Wall Plugs Cubicales System

Installtion for ZMS Nylon Series all complete as per direction of Engineer-in-charge

Wood work in upper rails of railing, hand rail of staircase, balcony etc. includig necessary bend, moulding fitted and fixed complete (for purpose of payment section will be measured in the square).

Providing and fixing Automatic Sliding door operator and 12mm toughened (Saint Gobain/AIS/Modiguard) glass all complete, ES 200 Easy 6250, compliant with future European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and the VDE regulations. T+-├║V design tested for durability of 1 Million Cycles, tested according to the low voltage guidelines, fulfils DIN 18650 standards, for framed glass door application with dormakaba or equivalent ST-Flex Profiles Systems, modular design including internal cover and with 12.52 mm Laminated glass for 2 Nos sliding door panels and 2 Nos fixed panels, both sliding & fixed panels with dormakaba or equivalent ST-Flex framed profile system with Interlocking Seals. Operator & Frame Finish should be Silver Anodized E6/C0, with operator dimensions (H x D) : 100 x 180 mm and of length as required to suit the opening size given below. dormakaba or equivalent ES200 Easy Operators are of very sturdy design with Self balancing Panel suspension system and with Anti-Jump fitting. The track profile should be separate from the main profile for enabling reduction in vibration insulation, With backplate for easy Installation. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, with SMPS, Class of protection IP 20. Activators- dormakaba or equivalent Eagle 6 Safe Combination Radars System (02 Nos) on Inside & Outside, Light barriers comprising receiver and transmitter - 02 Pair with Electro-mechanical locking, Bistable, Program Switch with Key. ES 200 Easy, Max Panel Weight Carrying Capacity of 2 X 100 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC . The requirement in total is as mentioned below: SIZE- 2000X 2400 MM Make: dormakaba/Assabaloy/Geze

STEEL WORK

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing 12mm thick toughened glass /partition,panels of minimum size . fixed to the sides of the staircase/ beams with necessary SS fasteners, either inserted in the RCC or welded. The steel surface either to be of mirror finish as approved by the client. All joints to be finished smooth.Architect/Engineer Incharge as may be necessary.)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C Fixing with adjustable lugs with split end tail to each jamb

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.

b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding,

cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete

as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places."

Providing and fixing Motorised rolling shutter - Model RS 107A, curtain made of single skinned aluminium laths, pressed galvalume steel hood motor cover, finish with one coat of grey,CE certified CRS compact gear P.R.C. make indirect drive operator , with three station push button with deadman control Rolling shutter

Providing and fixing Rama Rolling Shutter Industries make special for rolling shutter, made out of polycarbonate section made 304.8 X 98.3 X 5 mm, corner edge, with insert hollow 166 mm x 0.9 mm MS pipe in each section till the end opening, with nylon end lock at end both side for interlocking, special 35x35x5mm angle at bottom plate with bolt, 75 mm x 2.0 mm special guide channel, rolling shaft made out of (grade no-2 ) wire spring (make Jindal make or Usha Martin ), operation with mechanical device RAMA JM make gear box, Cast iron gear rolling shaft, with 22 mm solid rod system complete or auto operation RAMA- Jailong ( made in Asia) automatic motor system for rolling shutter, single phase, 230 V, input power from 320 (W) to 1768 (W) NM torque 225 to 1617, lifting force from 400 kg to 1500 kg, RPM- 4.2 TO 3.3, 50 Hz, manual chain in case of power failure and control switch.

Providing and fixing Italian make Boom barrier, model,securo plus 6C LED lighting system with variable flashing three push button fixed support pair of photocells with anodised aluminium vertical mountings.

Design, Manufacture,Supply and Installation of Flux polycarbonate multi-layered, Multicell Connectible modular panel system for, a complete assembly of coextruded UV protected polycarbonate panels incorporated into a complete system. Standing seam polycarbonate panel system.of minimum 25 mm thick (Min.) Panels with bigger width will be preferred for reducing number of joints in the roof. Panels shall be with grip lock double tooth locking mechanism with interlocking connectible connectors running lengthwise at both sides of the panel. Panels shall be fixed on Purlins of MS structure (will be paid Separately) with 3 numbers of self-drilling screws and specials Trapezoidal Heavy Duty Fastener to ensure a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005. The min width of the panel system shall be 1200mm (min.)Panels shall be solo opaque type in opaque and translucent clear combination with seven layers for required lux level along with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels with more layers will be preferred for better insulation and improved shading coefficient. Prices includes All acceosries including Aluminum profiles with EPDM Gaskets, at alernate edges with taper cutting to achieve the required profile, aesthetics and performance cirterias. U value shall not be more than 1.6 Watt/m2K as per EN ISO 1077-2:2018 and respective third Party test certificate shall be produced before procurement. Panels shall have an X cell strucutre also called truss bracing design to have more strenght and flexibility simulatneously. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155.Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing and direction of the engineering in charge.

FLOORING WORK

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 800 x 800 mm size

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 SQM

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for skirting,kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels, Granite of any colour and shade

Extra for pre finished nosing to treads of steps of marble stone.complete as per design approved by Engineer-in-Charge.

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, sers of steps etc., in required design and pattern wherever equired, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including ointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Providing 25 mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layer 19 mm thick (1:2:4) with 12 mm to 6mm size graded stone chips and top layer 6 mm thick (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/l

Provinding and fixing UPVC Foot rest all complete

Providing and fixing of 8mm thick Equitone "MINERALIS" through-coloured Fibre-Cement Cladding Panels as a ventilated-facade system on the exterior walls of the building using the exposed-fastening system with rivets to an aluminium substructure.

The vertical aluminium substructure shall consist of "T" and "L" profiles spaced at a maximum interval of 600mm c/c to coincide with the horizontal spacing of the rivets with provision for uninterrupted natural ventilation of min. 25mm space between the cladding panels and the structural wall from top to bottom. Vertical "T" profiles measuring approx. 120mm x 60mm shall be fixed at the vertical joints of two panels. Vertical "L" profiles measuring approx. 40mm x 60mm shall be fixed at intermediate fixing points, or where the edge of only one panel is to be fixed. At the outer corners, aluminium tubular profiles of 38mm x 62mm shall be used to take fixings of corner panels on adjacent faces of the building.

The aluminium substructure shall be fixed to the plastered masonry structure or unplastered R.C.C. structure using HDG Steel L-brackets with stainless steel screws and Hilti/ Fischer anchor fasteners as required at a maximum spacing of 1800mm c/c vertically (actual spacing to be derived from the structural calculation).

The Equitone MINERALIS Fibre-Cement Cladding Panels shall be riveted from the front to the vertical aluminimum sub-frame behind. The facade boards must be fixed with a fix-point in the middle of the board. All other fixations are sliding points. In case of two intermediate supporting profiles, two fix-points at the same horizontal level are allowed. The rivets shall have a maximum spacing of 600mm c/c in the horizontal direction and 600mm c/c in the vertical direction (however the actual rivet distances may be lower depending on the wind load). The rivets located near the panel edges shall be at a minimum distance of 30mm to 100mm from the vertical edges of the panels and 70mm to 100mm from the horizontal edges of the panels. Also, 6mm foam tape vertically to be fixed between mineralis panels and aluminium profiles.

The joints between adjacent panels to be an 8-12mm open grooves horizontally and 8-12mm grooves vertically (aluminimum profile running behind the grooves in vertical groove) and profile behind the grooves should be painted black on visiable surface (horizontally and vertically). A minimum open groove of 25mm shall be left open at the top and bottom of the Equitone MINERALIS Wall for air circulation which may be concealed using a perforated profile, complete all to the satisfaction of the Engineer-in-charge. Colour : All standard colours

Providing and Fixing of 6.5 mm Gym/Sports Flooring width of material 1.5 mm length 20 mtr Wear layer of material should be 1.2 mm and anti bacterial. weight of material 4800 g/per Sq Mtr Material should be passed from below test as per standard Shock Absorption >25% 38% sliding coefficient 0.4 - 0.7 0.5-0.55 Energy Return >0.31 0.50 Ball bounce >90% 94% Sound Isolation dB 26 All complete as per direction of engineer incharge.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.Granite of any colour and shade

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and fixing double charge vitrified wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

"Supplying and Fixing of MAKE IN INDIA broadloom carpet of WELSPUN MAKE ,100% Nylon Cut Pile , Digitally Printed , Pile Height 8.5 mm (± 1 mm),Total Height 10.5 mm (± 1 mm),Stitch / 10 cm 40.5(± 2% ), Pile Weight Net less Than 1200 GSM (± 5% ), Total Weight 2186 GSM (± 5% ), Secondry Backing PP Mesh, Gauge 1/8 Cut Pile, Latex Natural Rubber, Color fastness to LightTest Method: AATCC 16 (20 AFU) ≥ 4.0 at 80 Hours , Static Electricity Test Method: AATCC 134 Less than 3.5 KV, Hexapod test Method: ASTM D 5252 ≥ 4, Flammability (Radiant Panel),Anti Bacterial & Anti Microbial, Test Method: ASTM E 648 ≥ 0.45 (Class I) , complete as per drawing , specifications of the architect. Carpet Must Have CRI Green Label Plus Certificate for Good Indoor Air Quality. The carpet and Underlay (min 6-8mm) will be installed with standard SR 998/SR505/MAPAI Adhesives.The flooring to be installed as per the manufacture's specification and to be installed by its authorized agency or as Approved , with minimum 5 Years warrenty from Principal for any manufacturing defects . After Instalation carpet to be covered with transperent polythine to protect from dust,adhesive , colouring work at site ."

Providing and laying vitrified Cool Roof tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 154557-2007 / 15013006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. Its solar reflective index ( SRI ) value should be above 78. complete. Size of Tile 300x300 mm x10 mm thick. Parking Tiles (industrial Tiles)

Providing and laying factory made hamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge.80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineerin- Charge :

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.Granite of any colour and shade

Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge:

ROOFING & WATER PROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Roof/Terrace Water proofing:

Cleaning the roof area properly using compressed air system to ensure that the substrate is free from dust, laitance, debris, etc.

Supply & application of f Dr. Fixit LEC (Low energy consumption)system in order to achieve an initial U value of 0.51 W/m2.K including proper termination of the system on to the vertical surfaces as per following sequence

Spray apply an average 40 mm thk, Dr. Fixit Foam shield water blown polyurethane foam system with density of 45-50 kg/m3, thermal conductivity of 0.024 W/m K at 25 oC as per ASTM C - 518 / 91, compressive strength with rise of not less than 4.2 Kg/cm2 as per ASTM D-1621/94,Fire resistance property confirming to Class B2 as per DIN 4102, and water absorbtion per cm2 (gm/cc) with protective coating not more than 0.0019 as per ASTM C – 272. Over this apply two coat of roofseal, water based low VOC, single component cold applied waterproofing coating with an elongation of 500% and tensile strength 1.1N/mm2 as per ASTM D-412, water absorbtion ≤ 0.02% as per ASTM D-642 and tensile strength. Water ponding / Flood test after the application. Water shall be filled up and retained for at least 24 to 48 hrs.

After emptying the water, a Geotextile membrane of 150 gsm shall be placed.

A bitumen board or any other suitable board meant for construction joints shall be placed vertically at 3 to 4 metres along the length and breadth of the roof area. Each rectangular bay formed in this manner shall not exceed 12 m2. Average 80mm thick (or an equivalent thickness to achieve the required slope) Fibrated concrete screed of M 20 grade with Glass / polypropelene fibres shall be cast into these bays from a RMC pump (material, pump / machine shall be provided by you free of cost). The panel joints to be cut and sealed with polysulphide sealant, Pidiseal PS 41 G / 42 P. The width of the sealant fill shall not be more than approx. 10 mm and 10 mm deep.

Providing & applying two coats of UV resistant waterproof acrylic coating having SRI value >95, Dr. Fixit Newcoat Ezee by roller / brush or spray application over roof surface, parapet walls & pedestals including surface preparation, cleaning & priming complete.

Toilet/Kitchen Water proofing:

Surface preparation by grinding machine, cleaning , crack filling etc. complete Wrapping all pipe inserts with a two-way adhesion tape, Dr. Fixit Bathseal Tape, in the bathroom floor or wall or in the sunken portion, that is in contact with the pipe, promoting high adhesion between the grout and the pipe surface.

Grouting the gaps (annular space) between the pipe periphery & the inner side of the hole in the wall, with Dr. Fixit Bathseal Grout, cementitious, expanding, non-shrink grout that can give high early as well as ultimate strength to the grouted portion. Curing shall be as per good concrete practices, to ensure proper hardening and development of strength in the grout. Not more than 15% of water by wt. of the grout powder must be added to get proper flow and the physical strengths.

Providing and laying of fillets at the junction of slab and vertical walls prepared with cement sand mortar in the ratio 1 : 3 admixed with 5% of Dr. Fixit Pidicrete URP by weight of cement.

Applying two coats of Dr. Fixit Bathseal 2K ( 2 component, pre packed, cementitious flexible waterproofing coating with more than 100% elongation )@ 0.6 – 0.7 Sq.m. per kg in two coats all over the sunken portion floor, including over angular fillet, and extendable upto 300 mm over floor, achieving a uniform minimum thickness of 1.0 mm, all over the sunken portion of bathroom. Fixing of 150mm wide strip of woven glass fiber mesh all over the angle fillet all complete as per manufacture’s specifications.

Laying of protective plaster admixed with Dr.fixit Pidiproof LW+ (cement sand to be provided by client free of cost)

Basement waterproofing

Basement waterproofing:( Treatment below Raft) Clean all dirt, loose material and kept dry. In case of pot holes/cracks, the same shall be repaired with cement putty using Dr. Fixit Pidicrete URP. (Sand cement to be provided free of cost at site)

Providing and laying 1.5 mm thick, non perforated ,HDPE cross laminated film faced self adhesive bituminous waterproofing membrane Dr. Fixit Samshield XL1500 over the PCC etc as complete. The elongation (L/T) % should be 230/180 as per ASTM D 882, Tensile strength (L/T) ( N/mm2) should be 42/48 as per ASTM D 882, Tear Resistance (L/T) (N) 340/310 as per ASTM D 1004 , Puncture Resistance should be more than 220 N as per ASTM E 154 , Hydrostatic pressure more than 50 m as per BS EN 12390 ( Part 8 ), Water absorption @24 hrs (g/sqm) should be 0.14 % as per ASTM D 570 , Water vapor transmission (g/sqm/24 hours) should be less than 0.1 as per ASTM E 96 , Chemical resistance (pH) should be 2.5 – 11.5 as per ASTM D 543 and Crack bridging ability should be more than 1.5 mm as per ASTM C 836

Supply & installation of 180 gsm geotextile as a protection layer. Protecting the membrane with 50mm thick Screed (P.C.C) (In the scope of main contractor or client)

For Retaining wall (External Side): The entire area shall be taken up for thorough surface preparation with compressed air blow and mechanical removal of debris, laitance, etc. It shall be waterproofed with a mechanical spray application at an average thickness of 1.5mm with Dr Fixit Extensa , a water-based, zero-VOC, eco-friendly, 2 part hybrid polymer based liquid membrane comprising of liquid base and its catalyst, applied with a special twin nozzles compressed air operated gun. This spray applied waterproofing membrane shall be exhibit outstanding properties of adhesion onto the substrate with a peel adhesion of at least 25N as per ASTM C 794. The membrane shall adhere to the substrate within 60 seconds of application and shall facilitate a walk- over within 5 minutes of its installation. It shall possess an elongation of at least 1000 % when tested in an independent laboratory for extensibility (ASTM D 412) & give a full recovery after the elongation. It shall possess a self-sealing property and be UV stable (ASTM G 155 for 1000 hours - accelerated weathering).

It shall exhibit a tear strength of at least 5 N / sq/mm. when tested for ASTM D 1004 and shall never puncture even if tested in accordance with ATM E 154, stretched to the limit. Water permeability in the said waterproofing material shall be nil as per BS EN 12390-8 & water vapor transmission shall not be more than 2 g/hr/ sq.m. when tested as per ASTM E 96, and shall surpass the impact resistance test as per ASTM D 3746.

Providing & laying a protection layer over the waterproofing membrane throughout the retaining surface with kinni foam boards / Dimple board etc, before soil back filling begins.

Termination Detail: Use a C- Shaped aluminium flashing strip or tuck it into a concrete wall of a groove of 12mmx12mm .T he aluminium flashing can be fitted to press the membrane into the groove and then be filled with a single component PU sealant .

Waterproofing of Water Tanks

Cleaning the surface free of dirt dust, laitance & loose substrate.Removing the local depressions with Dr. Fixit URP modified mortar & cure it for 3 days.On construction joint/honey combed concrete Providing aluminium nozzles ,drilling at a distance of .75mtr & grouting with cementitious slurry mixed with expansive grout into each nozzle.Providing & constructing gola of 75x75mm thickness all along the wall & slab joints.Cleaning the surface with wire brush etc to make it free from foreign particles & making the surface in SSD condition.

Providing & applying three coats of Dr. Fixit Fastflex at the rate of 0.5 – 0.55 sqm per kg with a fibre mesh reinforcement in-between on the overall surface & allow it to cure as per the instructions given. The elongation should be more than 150% as per ASTM D 412 , Reduction of rapid chloride permeability (compared to control ) should be 92% as per ASTM C 1202-97 and Tensile strength ( 1.7 – 1.75mm), N/mm2 should be 5.0 as per ASTM D 412.

Providing & laying a protection plaster of 15-20mm thickness admixed with Dr. Fixit Pidiproof LW over the cured waterproofing treatment. ( In client’s scope )

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Cleaning and washing the surface of dirt and laitance to remove all the loose materials by various mechanical.

Filling of cracks Dr Fixit Pidicrete URP Modified Mortar in the ratio Cement: Sand (1:4) and 5% by weight of cement. (Sand cement to be provided free of cost at site)

Rounding of the junction of the walls and the slabs using cement mortar of 1:4 mix admixed with a integral waterproofing compound confirming to IS 2645 like DR. FIXIT PIDIPROOF LW @ 200 ml per 50 kgs bag of cement. (Complete item in client’s scope)

Injection grouting to be done at construction joints at 1 meter c/c with cement slurry modified with Dr.Fixit Pidicrete AM @225gms per 50kg bag of cement.

Applying three coats of Dr. Fixit Fastflex of M/s Pidilite Industries Ltd. @ 10 Sqft /kg/coat minimum thickness of 2mm and sprinkling sand over the third coat for better adhesion with plaster. The interval between each coat of Fastflex application is 6-8 hrs.. The elongation to break should be >150% as per ASTMD 412 , reduction of rapid chloride permeability should be 92 as per ASTM C 1202-97 and tensile strength should be 5N/mm2.

Carry out the grouting for light fitting casings, pipes, inserts, etc., provided in the concrete raft floor and walls using non shrink Dr. Fixit Bathseal Grout . Wrap all pipe inserts with a two-way adhesion tape, Dr. Fixit Bathseal Tape.

Providing & laying glass fibre mesh of 2.5 mm x 2.5 mm weighing 50 gsm at the pool around the insert pipes and the wall-to-floor junctions between the first and second coats

Providing & laying of tiles and apply Roff RTM epoxy grout to fill the gaps in the tiles

FINISHING WORK

Providing 12mm cement mortar (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, entilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

1-Sturcture Glazing

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/ structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent biMTR.allic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the periMTR.er for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc.,

enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having

all the performance characteristics etc. all omplete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in SQM. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 SQM from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing MTR.hod for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331- 09 testing MTR.hod for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing MTR.hod for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME- 330-10 testing MTR.hod for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing MTR.hod for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

LIFT WORK

Providing and fixing of 16 Passenger Lift/ 1088Kgs / 1.25 Speed / 9 Floors / 9 Stops /n Stainless Steel (1.5 Mm) Car Cabin approved design

Providing and fixing of 16 Passenger Lift/ 1088Kgs / 1.25 Speed / 10 Floors / 10 Stops /n Stainless Steel (1.5 Mm) Car Cabin approved design

Providing and fixing of Good lift (2 speed) 02 Ton Lift / 0.5 Speed / 10 Floors / 10Stops

Providing and fixing of Escalators in all complete direction by approved design.

SITC of Organic waste converter machine (OWC) with in-built shredder for waste conversion capacity of minimum 100 Kg/day, with minimum batch capacity of 10 kg per batch with facility of fully automatic operation .The OWC inner Tank shall be of SS 316 Grade & should be operated with electric motor and compatible with local resource / electric connection with complete installation on site including one year maintenance period / and basic training to client staff (for minimum 7 days) for successful day to day operation. The following modal /brand or equivalent is recommended /approved: Excel Industries Ltd. / NETEL INDIA -NETEKECO BIOMALI NetelEco Biomali NE 100S / ALPHATHERM with capacity of 100 kg /per day/ECOBOT Fully Stainless Steel EB-100 / SMART Xpress /Nachiket Note: All the equipments including the accessories supplied as per the above mentioned item should carry comprehensive warranty (including all spares, accessories and consumables) for maintenance period mentionedin this item.During this period, the successful Bidder shall replace all defective parts / accessories, consumables and attend to all repairs/break downs and undertake stipulated number of preventive maintenance visits to every user installation site. The cost of spare parts for all replacements has to be borne by the successfuls Bidder during the period of comprehensive warranty. Complete Work shall be carried out as per technical specifications

FALSE CEILING & PARTITIONS

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/SQM(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia MTR.er 50 mm length or suitable anchor fastener or MTR.al screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or MTR.al

screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm Each) to be provided at the horizontal joints of two boards, fixed to the studs using MTR.al to MTR.al flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS: 2095: part

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/SQM (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm Each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing periMTR.er channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the periMTR.er of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMTR.er channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of periMTR.er channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing GI Clip in MTR.al Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the periMTR.er of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/SQM (both side inclusive), fixing with clip in tiles into spring 'T' with:

GI MTR.al Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ SQM (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing & Fixing laminated wooden false ceiling , made in 50x50mm Hard wood frame (Mirandi) center to center 600mm both ways, hang to ceiling with help of hanger support 'L' type G.I angle (25x25mm) and anchor bolt etc. over fixed 11mm thick MDF board with 10x8mm deep groove finish with lacqure polish, 1.0 mm thick approved shade laminate to fixed on MDF board, defects free bubbles free with help of adhesive. as per drawing and to the entire satisfaction of Engineer in charge. ( MDF Boad & Laminate Make Green ply/Century /Merino or Equivalent ,Adhesive make Pidilite or equivalent)

Providing and making cove in gypsum board.false ceiling with all accessories.as per drawing and instructions of Engineer in charge .

Providing and Fixing MDF Wall Panneling made in hard wood frame (mirandi) 35mm x 50mm thick c/c 600mm horizontally & vertically, fixed to wall/columns with wooden plugs,then 11 mm thick Medium Density Fiber Board fixed on top of frame with 10x8 mm deep Groove & same finished with 1.0 mm thick laminate of approved quality pasted with the help of adhesive & nails screws etc. All grooves to be finished with lacquer polish maching with laminate shade as per Technical specification, drawing and instructions of Engineer in charge. (MDF Board & Laminate Make Green ply/Century /Merino or Equivalent, Adhesive make Pidilite or equivalent,MDF base rate Rs. 285/-sqm & Laminate base rate Rs.403/- sqm).

P/Fixing Wall paper as per approved brand and manufacture to give an even shade and color as approved by architect. & instruction of Engineer in charge.

Providing & Fixing premium quality Roller blinds Micro-Aerated - coated fabric to provide subtle view of the side of the blind and insulates and dissipates heat.Fabric shall be recycleable. Composition: 40% Polyester / 60% PVC Weight:400 g/m2 (+/-5%)Thickness:0.45 mm (+/-5%)Fabric Openess Factor: 4%Visible Light Transmission: 3% - 5% (N-N)Solar Transmission : 4% - 21%Solar Transmission : 4% - 21%Solar Reflectance : 7% - 70% Solar Absorption : 9% - 89%Tensile Strength (Warp/Weft): 220/220 daN / 5cmTearing Strength (Warp/Weft): 30/25 daN Management system for Quality : ISO 9001 Fire Retardancy:M2 (NFP92-507)Fabric Warranty: 5 Years Roller Tube shall be of extruded Aluminum alloy 38mm O.D (or as per system dimension) with a minimum wall thickness of 1.0mm duly anodized for long life. Clutch shall be wrap spring design with high strength fiberglass reinforced polyester assembly and high carbon steel springs to transmit motion from driving to driven members of clutch mechanism. Clutch shall operate by directionally with the use of an endless beaded chain. Clutch mechanism shall be crash proof, prevent slippage and shall raise and lower smoothly to any desired height. Clutch shall never need adjustment. Idler shall be of high strength fiberglass reinforcedpolyester, consisting of an outside sleeve and center shaft. Sleeve shall provide bearing surface for roller tube and rotate freely on center shaft, providingsmooth,quiet and long wearing operation. Brackets shall be of atomized steel powder coated to give superior finish. Bracket shall accommodate overhead, side or face mounting with clutch assembly on either end of the roller. Bottom of the blind shall be provided with aluminum tube powder coated. The fabric shall be enclosed in the suitably created pocket along with the tube. The tube shall be closed from sides with end caps to give a neat look. The blinds shall be of mullion to mullion width. Approved Makes - Hunter Douglas, GRABER, LUTRON/Equivalent

EXPANSION JOINT WORK

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063)

Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre- engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063).

Roof Joint of 100 mm gap

CARRAIGE OF MATERIALS

SAND (UPTO 8KM LEAD)

CHIPS (UPTO 25KM LEAD)

Metal (UPTO 25KM LEAD)

BRICKS (UPTO 7+1 KM LEAD)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cement morter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I.

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Larsen & Toubro 5 HP Starters Control Panel for Submersible Pump Larsen & ToubroR (5 HP)

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

ROAD WORK

Excavation in soil using Hydraulic Excavator CK 90 and Tippers with disposal up to 1000 meters. (excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including setting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within al lifts and lead up to 1000m) including Royalty @ Rs. 24.00 per cum, cost of watering, rolling & compaction.

Granular sub-base with close graded material (Table 400-1) - By mix in place method (construction of granular sub base by providing close graded material, spreading in uniform layers with motor graded in prepared surface, mixing by mix in place method with rotator ta OMC and compacting with vibratory roller to achieve the desired density, complete as per clause 401) For Grading -II Material For 53 mm Mix Size

Dry Lean cement concrete Sub-Base (Construction of Dry Lean Cement Concrete Sub-Base over a prepared sub grade with coarse and fine aggregate confirming to IS:383, the size of coarse aggregate not exceeding 25mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10MPa at 7 days, mixed in batching plant, transported to site laid with a paver with electronic sensor, compacting with 8-10 tones vibratory roller finishing and curing)

Cement Concrete Pavement (Construction of unreinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @400 kg cum, coarse and fine aggregate confirming to IS 383, maximum size finishes to lines and grades as per drawing.)

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete.New work (Two or more coats)

CC Pipe NP 4 heavy duty non presure pipe 900 mm dia with spigot

Design, Supply, Fabricating, Installation, Testing and Commisioning of FAÇADE ACCESS SYSTEM

Double Suspension Standard Cradle (2.5m*0.7m*1.1m) Standard Cradle Features: 1. Stainless Steel Perforated Cladding & SS 304 stirrup and structural Aluminum frames. 2. Aluminum chequer plate deck 3. Stainless Steel Sheet Cladding (long life, resistant to dents, corrosion, discoloring) 4. Safe Working Load 240 Kg 5. Designed & in compliance with the Safety Standard as per EN 1808 Standard Make : Appletree Building Maintainence pvt ltd.

NP01 Aluminium Monorail Track The NP01 monorail systems are specially extruded Aluminium Monorail Track, 6351 T-6 grade. The aluminium monorail track is supported by monorail brackets which will be mounted on RCC structure as per project requirement. The profile of monorail track is contoured to suit the traversing trolley on which the cradle is suspended. The cradle will be suspended with the help of ETT that will traverse on the monorail track. The profile is installed with joint pins, end stopper and suitable bolt sets, and it is fixed to a suitable steel bracket. Normally the monorail can carry maintenance units like: Double Suspension Standard Cradle Make : Appletree Building Maintainence pvt ltd.

Monorail Brackets @1.5m The monorail brackets are manufactured out of mild steel which are fixed with the RCC structure as shown in the drawings at 1.5m c/c with the help of SS 316 Appletree Make anchors by using Hilti/Fischer chemical as per design calculations. The RCC structure is at client’s scope and it should be able to undertake the load of the cleaning system as per design calculation. The fixing of the monorail brackets should be in such a way that it can facilitate levelled layout of monorail track for easy operation. Make : Appletree Building Maintainence pvt ltd.

SS316 M16x55 Hex Head Bolt & Nut with P&S Washer Make : Appletree Building Maintainence pvt ltd.

SS 304 Appletree Make Anchors fixed with Hilti/Fischer Chemical Make : Appletree Building Maintainence pvt ltd.

Electric Traversing Trolley Traversing trolley is electrically operated. The trolleys will have wheels for holding on to the monorail track. The trolley will have the provision for fixing the galvanized steel wire ropes to suspend the cradle. ETT will be contoured over monorail track with its specifically designed profile. Make : Appletree Building Maintainence pvt ltd.

BMU Type 02- Safety Line Fall Arrest System

Safety line Stainless Steel Wire Rope- Material: SS 304, 8.3mm dia Min Breaking Strength - 60 KN Integrated Shock Absorber cum Tensioner- Material: Stainless Steel 304 & AB2 Aluminium Bronze Cast Alloy Min Breaking Strength - 22.2 KN End Swage Less- Material: AB2 Aluminium Bronze Cast Alloy Min Breaking Strength-22.2 KN Equipped with swage less wire locking mechanism. End Anchorage- Material: Stainless Steel 316 Min Breaking Strength - 22.2 KN Use to connect Shock Absorber and End Swage to respective roof post. Full Body Harness with energy absorbing lanyard- Conform to EN 361:2002 Breaking Strength 25KN Convenience - metal components made up of steel Adaptability - adjustable Thigh straps. Attachment Elements - 2 chest attachment Textile Loops, A Dorsal attachment D-Ring for fall arrest. Rope Graber with adjustable lanyard- Polyamide Kernmantle Rope with rope grabber. Adjustable lanyard to access the different parts of roof

BMU Type 03- Plate type Eye hook

Plate type Eye hook Eye bolt shall be designed in such a way to avoid wear and tear of suspension shackles and anchor shall withstand the shock absorbance. Eye bolts shall be fixed in pairs at required intervals and bolts are to be fixed only into MS/SS structure as per site condition, by welding. Eye bolts made out of Mild Steel/Stainless Steel. DESIGN STANDARD: 1. BS EN 1808-2015 2. BS EN 7985-2013 3. BS EN 795-2012 Make : Appletree Building Maintainence pvt ltd.

BMU Type 04- Telecopic Cleaning Pole

Telecopic Cleaning Pole (Pole Height = 12m) Telescopic poles are available in different lengths and with ergonomically shaped handles. Due to the light and stable aluminium material, the telescopic pole is ideal for cleaning glass surfaces. As professional glass cleaning often requires cleaning at height, telescopic poles allow safe working from the ground up to a height of 12 m. Make : Appletree Building Maintainence pvt ltd.

BMU Type 05- MS Ladder

MS Ladder ( Height = 8.5m) Make : Appletree Building Maintainence pvt ltd.

BUILDING LIGHTING AND AUTOMATION

Supply of Front Side Façade of Building which includes Mono Colour Effects on the Wings Front Side and RGB Effects on the wall near Entrance at the Front Side and SITC of DMX and Other Accessories including programming of the system

Lighting Control & Automation

Supply of Lighting Control Module, Integrating Device, Sensor and Software for Daylight Harvesting, Occupancy and time scheduling and software programming.

Supply of Power Supply module 2400mA

Supply of 1port Programming IP Gateway Module & Logic with enclosure, monitoring software and BMS Integration

SITC of 64 CH DALI Ballast Dimming Actuator

SITC of Daylight Sensor

SITC of 8CH 16A Relay module for Switching

SITC of Touch Panel Granite with Power Panel Interface

SITC of Standalone Sensor

ELECTRICAL WORKS

METERING INDOOR UNIT

Providing & fixing 11KV CT & PT in above metering indoor unit and getting them calibrated from State Electricity Boards before fixing. And as per the approved make of State electricity board

11KV SINGLE VCB PANEL BOARD (NEAR METER)

Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following:

Single Panel Board

Incomer:-

1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC

Each incomer comprising with following accessaries.

1 No. Mechanical ON/OFF Indicator

1 No. Aux Switch 6NO + 6NC

Panel, Busbar, CT, PT

1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable

3 Nos. Resin Cast CTs 100/50/1-1A with Core 1 : 7.5VA CL 1 Core 2 : 7.5VA CL 5P10

3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA

Breaker Panel indication Lamps :

6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged

Switches and other Accessories

8 nos.Fuses

1 No. Heater

1 No. Thermostat

1 No. 6 Window Annunciator

1 No. Plug & Socket

1 No. Test Terminal Block

1 No. T-N-C Switch

1 No. Emergency Push Button

1 No. Hooter

Meters

1 No. Analog Ammeter + ASS

1 No. Analog Voltmeter + VSS

1 No. Digital Multifunction Meter - Quasar

Relays

1 No. MC 61A (O/C + E/F - IDMT+Inst)

1 No. AVAJH13 Master trip relay (Ashida)

1 No. TCS Relay

Single VCB Panel Board

11KV PANEL BOARD NEAR TRANSFORMER

Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following:

3 Panel Board ( 1 INCOMERS & 2 OUTGOING)

Incomer:-

1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC

Each incomer comprising with following accessaries.

1 No. Mechanical ON/OFF Indicator

1 No. Aux Switch 6NO + 6NC

Panel, Busbar, CT, PT

1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable

3 Nos. Resin Cast CTs 125/60/1-1A with Core 1 : 7.5VA CL 1 Core 2 : 7.5VA CL 5P10

3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA

Breaker Panel indication Lamps :

6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged

Switches and other Accessories

8 nos.Fuses

1 No. Heater

1 No. Thermostat

1 No. 6 Window Annunciator

1 No. Plug & Socket

1 No. Test Terminal Block

1 No. T-N-C Switch

1 No. Emergency Push Button

Meters

1 No. Analog Ammeter + ASS

1 No. Analog Voltmeter + VSS

1 No. Digital Multifunction Meter - Quasar

Relays

1 No. MC 61A (O/C + E/F - IDMT+Inst)

1 No. AVAJH13 Master trip relay (Ashida)

1 No. TCS Relay

Outgoing:-

2 No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC

Busbar :-

1000 amps TP Cu, bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Each Outgoing comprising with following accessaries.

1 No. Mechanical ON/OFF Indicator

1 No. Aux Switch 6NO + 6NC

Panel, Busbar, CT, PT

1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable

3 Nos. Resin Cast CTs 60/30/40/1-1A with Core 1 : 7.5VA CL 1 Core 2 : 7.5VA CL 5P10

Breaker Panel indication Lamps :

6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged

Switches and other Accessories

8 nos.Fuses

1 No. Heater

1 No. Thermostat

1 No. 6 Window Annunciator

1 No. Plug & Socket

1 No. Test Terminal Block

1 No. T-N-C Switch

1 No. Emergency Push Button

Meters

1 No. Analog Ammeter + ASS

1 No. Digital Multifunction Meter - Quasar

Relays

1 No. MC 61A (O/C + E/F - IDMT+Inst)

2 Nos. Auxiliary Relay for transformer fault

1 No. AVAJH13 Master trip relay (Ashida)

1 No. TCS Relay

Three VCB Panel Board

11KV/ 0.433KV 1000KVA TRANSFORMER

Supplying ,Assembling , erecting, testing and commissioning of 1000 KVA 11KV/0.433KV voltage 3phase 50Hz, indoor type copper wound, Dry type cast resin step down transformer complete with all modern fittings as given in the specifications including , lifting lugs, Roller type bi-directional wheels, suitable boxes on both the ends for cable entry & bus duct,winding temprature indication & alarm, , earthing terminals, diagram and rating plat etc. as required.

The transformers shall be installed in hot, humid tropical atmosphere. All equipment accessories and wiring shall be provided with tropical finish to prevent fungus growth

The transformers shall be dry Type & capable of continuous operation of rated output under the operating conditions of voltage and frequency variations as per statutory limits governed by relevant Indian Standard and Indian Electricity Rules, 1956 / IEC with latest amendments in force.

Requirement: 11KV/433V voltage dry type cast resin with OFF LOAD Tap Changer, Tapping range +7.5% to -15% in steps of 2.25% (HV side), neutral air cooled, double copper wound, core type suitable for packaged substation housed in a enclosure.

Voltage Ratio: No load voltage 11000/433volts within tolerance as stipulated in latest IS standard.

Insulating material shall be of proven design. The insulating materials shall be class “F”

Rating: The transformer shall have a continuous rating as specified at any of the specified tapping position and with the maximum temperature rise specified.

Temperature Rise: The maximum temperature rise at the specified maximum continuous output shall not exceed 90°C by thermometer of winding above ambient temperature of 50°C.

Type of Load: The transformer shall be suitable for carrying unbalanced load up to 90% load within temperature rise indicated in the Indian Standard specification ‘Guide for loading of dry Transformer

Overloads: The transformers shall be suitable for carrying overload within temperature rise indicated in IS ‘Guide for Loading of dry transformer’.

Connections: H.V. Delta and L.V Star connected with neutral brought out on the secondary side for connection to earth; Vector group DYn11 of IS:2026

Each 33KV/415V Dual voltage Step down transformers shall be provided with the following fittings and accessories: Rating diagram and terminal marking plate for transformer.

Lifting lugs for transformer

Bi-directional Rollers

Rating diagram and terminal marking plate for transformer

Earth terminals (2 Nos) for body earthing for transformers

Inspection door for access to terminal connections for transformers

Suitable cable termination arrangement for M.V. side with extended Bus bars for cables or Bus duct connection and cable box terminations on H.V. Side, suitable for 3C x 240/300sq. mm 11 K.V. XLPE Aluminum Conductor cable.

Necessary hardware, clamps, lugs etc. for terminations of H.V. Cables on HV side and cable termination on M.V. Side.

Winding temperature indicator with contacts for remote alarm and tripping.

DG SETS and BATTERY CHARGER

Supply, installation, testing & commissioning of 415 V, 750 kVA stand by rating ( radiator cooled type ) diesel generating set along with base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, Batteries, Battery Charger, Instrumentation, day oil fuel tank including the piping of approx. 12 mtr, Silencer with Bellows, Alarms, Engine Control Panel, AVM Pads, AVR Panel, Terminal Arrangements including bus duct termination box with all associated equipment / work as per specifications. Alternator shall have class-H insulation and rated for 680 KW output at 47deg. C. Engine shall not be derated upto 50 deg.C ambient. (First Fill oil of 990 litre for Day oil tnak to be considered in the offer). Supply and installation of suitabkle dia SS flexible bellows with matching flanges along with required hardware i.e. gasket, nut bolt, washer etc as required.

Supply, installation, testing & commissioning of 415 V, 500 kVA stand by rating ( radiator cooled type ) diesel generating set along with base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, Batteries, Battery Charger, Instrumentation, day oil fuel tank including the piping of approx. 12 mtr, Silencer with Bellows, Alarms, Engine Control Panel, AVM Pads, AVR Panel, Terminal Arrangements including bus duct termination box with all associated equipment / work as per specifications. Alternator shall have class-H insulation and rated for 680 KW output at 47deg. C. Engine shall not be derated upto 50 deg.C ambient. (First Fill oil of 990 litre for Day oil tnak to be considered in the offer). Supply and installation of suitabkle dia SS flexible bellows with matching flanges along with required hardware i.e. gasket, nut bolt, washer etc as required.

Supply, installation, testing & commissioning of acoustic treatment for DG room with 75mm thickness with 2 layer i.e. 25mm ceramic wool & 50mm thick mineral wool insulation with not less 96kg/cm2 density wrapped in chicken mesh and clad with 24 gauge aluminium sheet including all supporting structure as required.

Supply, laying of following sizes of MS Piping for Exhaust including providing suitable bends, reducers & supporting arrangement at suitable intervals including insulation on entire length of exhaust pipe with 50mm thick Rockwool insulation & painting etc. as required.

250 mm dia

400 mm dia

EXTERNAL ELECTRICAL WORKS

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coatof neat cement complete as per standard design :icks of classdesignation 7.5

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100 mm dia

150 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required

63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

Supply of 7.0 Mtr High Octagonal pole ( Hot Dip Galvanized) BOP-7030 with top dia 70mm and bottom dia 130mm and made of 2mm thick base plate of size 200mmX200mmX12mm ( LXBXT) and with suitable size of foundation bolts and complete as required

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 6.5 metre and upto 8 metre

Supply, installation, testing and commissioning of 35W Kwp power rating high efficiency eco friendly with compact ascesthic design Integrated all-in-one solar street light with system efficacy ≥ 170 lm/watt CRI>70 IP-65 complete with all accessories sush as lithium ferro phosphate battery, Mono crystalline solar panel and MPPT charger and built into sensor based luminaire made of Pressure die cast aluminium and suitable bracket for top pole mounting etc complete as required.

Supply of 12.0 Mtr High Mast in one section construction S355 grade as per BS-EN-10025 Top dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanosation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47m/s as per IS :875 (part-III) with 6 nos. foundation bolt of PCD 445mm TS 600/24mm dia/850mm long luminaries carriage: material of 40NB ERW class B mM.S pipe dia of carriage ring 450mm (ID) with 8 arm, welded 2 section having carrying capacity upto 8 luminaries trailing cable 5core 2.5sq.mm PVC flexible copper conductor winch/power tool double drum SWL 350kg with 0.75HP 6pole single speed integral motor rope grade AISI:304, 7/19 construction dia 5mm BLC 1450x2 having 2nos. of continues rope. Aviation obstruction light twin dome aviation obstruction light LED type required. feeder pillar control panel housing 32a TPN MCB incoer single dial timer 25A contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for power tool & Remote control.

For 120MT High mast : ITC of high mast light fixture with the help of suitable tools and plants wiring of luminaries with material like insulared PVC sheathed flexible cable of suitable copper conductor lugs MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil beaninh capacity of 10T/MT high mast.

Supply of following sizes sizes of PVC insulated PVC sheathed aluminium conductor armoured 1.1 KV grade as as required.

2C x 6 sq mm

2C x 10 sq mm

2C x 16 sq mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required Upto 35 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

2C x 6 sq mm

2C x 10 sq mm

2C x 16 sq mm

Supplying and fixing of outdoor type junction box( IP 67 ) suitable to incoming and outgoing up to 16 sq. mm Al Armoured Cable. The juction box shall also be suitable for 3 Nos. outgoing circuits each consisitng of 3 Nos. 2.5 sq mm copper wired wires

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring with 2 x 4.0 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4.0 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

LT CABLES

Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required.

PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1)

3.1/2 core 300sq. mm.

3.1/2 core 240sq. mm.

3.1/2 core 185sq. mm.

3.1/2 core 150sq. mm.

3.1/2 core 120sq. mm.

3.1/2 core 95sq. mm.

3.1/2 core 70sq. mm.

3.1/2 core 50sq. mm.

3.1/2 core 35sq. mm.

3.5 core 25sq. mm.

4 core 16sq. mm.

4 core 10 sq. mm.

4 core 6 sq. mm.

PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Copper conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1)

4 core 1.5 sq. mm. ( Copper Control cable)

7 core 1.5 sq. mm. ( Copper Control cable)

12 core 1.5 sq. mm. ( Copper Control cable)

Laying and fxing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall/cable tray surface as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 300sq. mm.

3.1/2 core 240sq. mm.

3.1/2 core 185sq. mm.

3.1/2 core 150sq. mm.

3.1/2 core 120sq. mm.

3.1/2 core 95sq. mm.

3.1/2 core 70sq. mm.

3.1/2 core 50sq. mm.

3.1/2 core 35sq. mm.

4 core 25sq. mm.

4core 16sq. mm.

4 core 10sq. mm.

4 core 6sq. mm.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032)

100mm width X 50mm depth X 1.6 mm thickness

150mm width X 50mm depth X 1.6 mm thickness

300mm width X 50mm depth X 1.6 mm thickness

450mm width X 50mm depth X 2.0 mm thickness

600mm width X 62.5mm depth X 2.0 mm thickness

750mm width X 75mm depth X 2.0 mm thickness

900mm width X 75mm depth X 2.0 mm thickness

11KV HT CABLE

Supply of cable XLPE -PVC insulated PVC sheathed galvanised steel strip armoured electric power cable with aluminium conductor 11000 volt grade of size 3CX300 sqmm.

Laying of one number XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 300 sq. mm

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required : 300 sq. mm

415V LT PANELS & DISTRIBUTION BOARDS

DG SYNCHRONIZING PANEL

AUTO STARTING, AUTO SYNCHRONIZING, AUTO LOAD SHARING AND LOAD MANAGING PANEL AND DG AUXILIARY PANEL

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of Synchronizing panel and DG Aux. Panel fabricated out of 14 gauge CRCA sheet steel in cubicle compartmentised free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T’ section and / or flats wherever necessary. 3 mm thick cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specification and final approved shade. 2 Nos. earthing terminals shall be provided for all panels. Panels shall be suitable for 415 V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in all panels. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels. ( DG sync panel shall be extensible type )

Incoming

Incoming for 2 No. 750 & 1No. 400 KVA DG sets each comprises the following and as per single line diagram.

1250 amps four Pole electrically operated fully drawout type air circuit breaker as per specification and with following accessories.

630 amps four Pole electrically operated fully drawout type air circuit breaker as per specification and with following accessories.

Each Incommer having following

Digital energy meter (Schneider – PM8000 or equivalent or equivalent) of accuracy class-0.2, with 3 Nos. --/5 amps 15VA CTs.

Battery charger with voltmeter of range 0-50 volts and ammeter of range 0-50 amps for trickle and boost charging.

3 Nos. phase indicating lights with control MCB’s.

Excitor field DC voltmeter and ammeter.

Breaker control switch.

Differential protection relay (87) with PS class CT’s on both side. ( 3 Nos. L & T SC14S )

Master trip relay, IDMT, under voltage.

Trip circuit supervision relay, over voltage, revers power.

24 V DC shunt trip.

Emergency stop push button.

Five push buttons – start, stop, reset, test and accept.

Three indicating lamps “load on set’, ‘Load on Mains’ and “ Set fail to start’.

12 Window alarm annunciators panel with hooter, push buttons, aux. Contactors etc as required as per specification.

Suitable rating battery charger as per specifications

Temperature scanner (Messi Bus/Procon)

Bus Bar

2000 A TPN electrolytic Al bus bar with heat shrinkable insulation sleeve.

Bus Coupler

1 nos. 630 amps & 1 nos. 1250 amps 4 pole electrically operated manually drawout type air circuit breaker, with ON / OFF / TRIP indicating lamps with control MCB’s, shunt trip, U/V release breaker control switch etc complete as per specs and SLD. - 1 Set.

Outgoings

2 No. 1600 Amps TPN electrical/manually operated fully drawout type air circuit breaker with built in microprocessor based release unit for short circuit, over current and earth fault protection with adjustable setting and ON/OFF/Trip & shunt trip coil etc. as per specification.

1 Nos. 400 amp 4 pole MCCB.

All breakers shall be electrically interlocked as per schematic diagram.

All ACB’s/MCCB’s shall be suitable for 50 kA breaking capacity.

PLC for load management , interlocking , DG auxiliary and supervision.

2 kVA UPS for 30 MinutesBackup for control wiring.

Touch screen display panel having 10.4 inch - TFT Display - Color screen as per specification.

Auto starting / Auto synchronizing / Auto load balancing and auto load management panel for 3 No. DG Sets as described above

1No. 24V DC Supply Power Pack with suitable (bidder shall provide the Ah calculation) Ah Maintenance free Battery back up. Power Pack should be with Protections of over voltage/ under voltage/ over charging.

MAIN LT PANEL CUM CHANGE OVER PANEL ( 50 kA )

Incoming Air Circuit Breaker from Synchronizing Panel

2 nos. 1600 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories :

Digital energy meter (Schneider – EM6400NG or equivalent) of accuracy class-1, with 3 Nos. 1600 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

24 V DC Shunt trip coil. - 1 Set

240 V under voltage release. - 1 Set

Breaker control switch - 1 Set

Reverse power relay - 1 Set

IDMT relay- 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

Incoming Air Circuit Breaker from Transformers

2 x 1600 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories :

Digital energy meter (Schneider – PM8000 or equivalent or equivalent) of accuracy class-0.2, with 3 Nos. 1600/5 amps 15VA CTs.

1 Nos. 1600/5 amps 15VA CTs for capacitor controller.

Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

24 V DC Shunt trip coil. - 1 Set

240 V under voltage release. - 1 Set

25A Breaker control switch - 1 Set

Three Phase Under voltage relay MV12 or equivalnt (27) - 1 Set

Three Phase Over voltage relay MV 12 or equivalent (59) - 1 Set

IDMT relay- 1 Set

Master Trip relay- 1 Set

10 Mode, 100kA Transient voltage surge suppressor with 63A 4 Pole 50KA MCCB.

Auxiliary contacts required for necessary interlocking of breakers.

Bus Bars

2000 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Bus Coupler

1600 amps 4 pole electrically operated manually drawout type air circuit breaker, with ON / OFF / TRIP indicating lamps with control MCB’s, shunt trip, U/V release breaker control switch- 1 Set.

Outgoing

AHF + CAP. PANELS 2 Nos. 630 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

HAVC PLANT PANEL - 2 Nos. 800 Amps TPN Pole manually operated fully drawout type air circuit breaker and ON/OFF/Trip & shunt trip coil.

RISING MAIN - 2 Nos. 1000 Amps TPN Pole manually operated fully drawout type air circuit breaker and ON/OFF/Trip & shunt trip coil.

UPPER BASMENT MDB - 3 Nos. 100/125/160 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

BASMENT VENT MDB - 3 Nos. 400/500 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

MAIN LIFT PANEL - 4 Nos. 125 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

STP PANEL - 1 Nos. 200 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

WTP PANEL - 1 Nos. 160 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

FIRE FIGHTING PANEL - 1 Nos. 160 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

EX LIGHTING PANEL - 1 Nos. 63 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

Spare

1 No. 800 Amps 4 Pole manually operated fully drawout type air circuit breaker and ON/OFF/Trip & shunt trip coil.

1 Nos. 630 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

2 Nos. 400 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

2 Nos. 250 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

3 Nos. 125 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil.

Notes :

All outgoing feeders shall have suitable range of followings:

All outgoing feeder shall have digital electronic energy meter ( EM 6438 of conzerv make or equivalent ) with suitable no. of CT,s and RS 485 port .

1 No. --/ 5, 15 VA dual ratio CT’s shall be provided for APFCR on each transformer's incomer.

Wiring and supply, installation of space heater, Humidistatae and control MCB’s shall be provided all vertical sections.

Suitable danger board shall be provided.

All bus bar section / backside panels shall have hinged type door.

All incoming / outgoing air circuit breakers shall be suitable for minimum 50 kA breaking capacity.

9 W fitting with LED lamp, switch shall be provided in each vertical section.

Incomer ACB receiving power from DG synchronizing panel shall have suitable provision for busduct connection.

Incomer ACB receiving power from transformer shall have suitable provision for Cables connection..

All Electronic Energy meter shall be pre wired for BMS connection upto central point within the panel with sheilded cable.

All incoming & outgoing feeders shall have minimum 4 nos. potential free contacts.

1No. 24V DC Supply Power Pack with suitable (bidder shall provide the Ah calculation) Ah Maintenance free Battery back up. Power Pack should be with Protections of over voltage/ under voltage/ over charging.

350KVAR CAPACITOR PANEL

INCOMER

1No. 630A TPN MCCB

METERING & INDICATION

1 set of phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

1 No. 12 steps APFC relay

1 set of Ammeter (0-1200A) with ASS and 3 nos.600/5A, CTs'

BUS-BAR

1 Set of 800A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

3 Nos.of 125A TP MCCB (35 KA) with 140A TP contactor (AC-3 duty)

5 Nos. of 100A TP MCCB (35 KA) with 70A TP contactor (AC-3 duty)

1 No. of 63A TP MCCB (35 KA) with 40A TP contactor (AC-3 duty)

1 Nos. of 32A TP MCCB (35 KA) with 20A TP contactor (AC-3 duty)

3 No.of 16A TP MCCB (35 KA) with 10A TP contactor (AC-3 duty)

8 Nos. self Illuminated Red-Green (ON-OFF) push buttons.

3 Nos. 50 KVAR capacitor Bank with discharge resistor.

5 Nos. 25 KVAR capacitor Bank with discharge resistor.

1 No. 20 KVAR capacitor Bank with discharge resistor.

1 No. 10 KVAR capacitor Bank with discharge resistor.

3 No. 5 KVAR capacitor Bank with discharge resistor.

Supply Receiving, fixing, testing & commissioning of of Capacitor panel as described above

Lower Basement MDB

Incoming

1 No. 125 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 125/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

6 No. 63 Amps 4 Pole MCCB and ON/OFF/Trip

6 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

Upper Basement MDB

Incoming

1 No. 125 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

6 No. 63 Amps 4 Pole MCCB and ON/OFF/Trip with Dual Source Meter

6 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1(RSH) &MDB-2 (LHS) - Ground Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

6 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

4 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1 (LHS) & MDB-2 (RHS)- First Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

7 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

4 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1(LHS) & MDB-2(RHS) -Second Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

9 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

4 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1 (LHS) & MDB-2 (RHS)-Third Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

12 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

4 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1 (LHS) MDB-2 (RHS)- 4TH Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

11 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

4 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1 (LHS), MDB-2 (RHS) - 5TH Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

11 No. 63 Amps 4 Pole MCB with Dual Source Meter with control wiring for AMR system.

8 No. 25/40/63 Amps FP Pole MCB.

Panel as described above.

MDB-1 (LHS) / MDB-2 (RHS) - 6TH Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 160/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

2 No. 100/125 Amps 4 Pole MCCB and ON/OFF/Trip with Dual Source Meter with control wiring for AMR system.

5 No. 40/63 Amps 4 Pole MCB and ON/OFF/Trip with Dual Source Meter with control wiring for AMR system.

2 No. 32/25 Amps FP Pole MCB.

Panel as described above.

MDB-1 (RHS) - Terrace Floor

Incoming

Incomming direct from tapoff box.

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

5 No. 40/63 Amps 4 Pole MCB and ON/OFF/Trip

2 No. 32/25 Amps FP Pole MCB.

Panel as described above.

Lift Panel - 1,2,3

Incoming

1 No. 125 Amps with 4 Pole MCCB with 125A ATS and ON/OFF/Trip

Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs.

Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets

Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

Bus Bars

300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set.

Outgoing

3 No. 40/63 Amps 4 Pole MCCB and ON/OFF/Trip

6 No. 32/25 Amps FP Pole MCB.

Panel as described above.

EXTERNAL LIGHTING FEEDER PILLAR OUT DOOR TYPE

INCOMER

1 Nos. 63/100Amp 16KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

1 Nos. 60Amp AC3 4P Contactor with timer be complete as required.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 100A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

10 Nos. 6/32Amp TPN MCB 10KA

EXTERNAL LIGHTING FEEDER PILLAR AS DESCRIBED ABOVE

EARTHING & LIGHTING PROTECTION

Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. ( with charcoal or coke and salt).

Earthing with copper . Earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.( with charcoal or coke and salt).

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25x5 mm copper strip in 40mm dia G. I. pipe from earth electrode including connection with brass nut, bolt, spring washer excavation and re-filling etc. as required.

S/L 25x6mm G.I. earth strip in ground: Proving and laying earth connection from earth electrode with 25x6mm G.I wire in 15mm GI pipe from electrode as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 32 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 6 mm Cu, strip on surface or in recess for connections etc. as required.

CU WIRE CONDUCTORS

Providing and laying following size CU insulated wire on surface or in recess in exising conduit/ cable tray for connections etc. as required.

6sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

10sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

16sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor

LIGHTNING PROTECTION

Prividing and Fixing of GI lightning conductor Finial made of 25mm dia 300 mm Long GI tube , having single prone on top with 85mm dia 6mm thick GI base plate including holes etc complete as required

Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for vertical run)

Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for horizontal)

Providing and fixing testing joint, made of 20 mm x 3 mm thick gi strip, 125 mm long with 4 Nos. brass bolts, nuts check nuts and spring washers etc. complete as required.

Providing and laying GI tape, 32 mm x 6 mm thick from earth electrode directly in ground as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

SUPPLY AND INSTALLATION OF LIGHT FIXTURES AND EXHAUST FANS

SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required 45W LED STREET LIGHT

SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required 50/60W LED FLOOD LIGHT

SITC of following ratings RECCESS /SURFACE MOUNTED LED ROUND / SQUIRE SHAPE DOWN LIGHT liminiaire with pressure dia cast housing FOR SINLE PHASE supply voltage luminaire shall be confirm to IS 10322 Part 3 section 2 or IEC 6-7 22 with all necessary accessory item required .

10/12 W LED ROUND SURFACE DOWNLIGHT STAIR LIGHT

15/16w LED RECESSED ROUND DOWNLIGHT CORRIDOR

10/12w LED RECESSED ROUND DOWNLIGHT TOILET

50/60w LED FLOOD LIGHT D.HIGHT AREA

2'x2' LED PANEL LIGHT

6w LED SURFACE BULK HEAD LIGHT

SITC of following ratings SURFACE MOUNTED LED tube light fitting, suitable for 230V 50Hz, single phase supply etc. complete as required.

10/12W LED Tube light

20/22W LED Tube light

SITC of following ratings LED Post top lamp made in dia cast aluminium housing with decorative clear/ opal acrylic diffuse on existing pipe including connection with 1.5sq mm copper conductor etc all complete as required. 20/25W LED post top lamp clear

SITC of following ratings approved make LED Bollard fitting, with rectangular shape of height 600 to 850mm power input 8/9 watt with dia cast aluminium housing opel with PC diffuser, [P:65/54 protection, confirming to IS:10322 part 5 etc all complete as required (excluding plinth charge)

LED strip light 24 volts DC with IP 65 rated in different colours of length 5 mtr and power 5 W per meter including driver IS: 10322 pert 5/ section-7.

Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours

Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required. 1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan

Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required.

Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required.

Supply of 12" (300mm) metal exhaust fan

Supply of 16" (400mm) metal exhaust fan

TELEPHONE, TV , DATA cabling with Raceways :

Supply & fixing of modular telephone cord outlet & switch box including connections but excluding modular plate etc. as required.

Supply & fixing of 1 or 2 module GI box along with modular base & cover plate of modular switches in recess etc. as required.

Supply & fixing of modular TV antenna socket outlet & switch box including connections but excluding modular plate etc. as required.

Supply & fixing of 1 or 2 module GI box along with modular base & cover plate of modular switches in recess etc. as required.

Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

20mm dia

25mm dia

32mm dia

Supply and fixing 1 or 2 module ( 75mm X 75mm ) GI Box along with modular base and cover plate for modular switches in recess etc as required

Supply and fixing of Computer terminal (RJ-45) outlet in existing box with modular plate

Supply and fixing of Outdoor type junction Box

Supply and Laying of Cat-6 Cable in existing conduits

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm copper conductor PE insulated, with PVC shield in the existing surface/ recessed PVC conduit as required.

Supplying, drawing, of 0.5mm dia (2 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required

Supplying, drawing, of 0.5mm dia (4 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required

Supplying and Fixing in floor with all accessories , 2 mm thick steel sheet factory fabricated post galvanized floor recessed raceway of the following sizes

225 mm wide x 38 mm deep raceway

100 mm wide x 38 mm deep raceway

Providing and fixing 400 x 400 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

Providing and fixing 300 x 300 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

Providing and fixing 150 x 150 x 50 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required

FIRE ALARM AND DETECTION SYSTEMS

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required.

2x1.5 sq mm

2x2.5 sq mm

Ten Loop Panel

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

PA SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required..

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installing, testing and commissioning of 2X1.0 SQMM IND. 1.1KV SPEAKER CABLE in existing conduit.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 300 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site

INTERNAL WIRING AND FINAL DISTRIBUTION BOARDS

Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit , with modular switch ,modular plate ,suitable GI box as required Group - C

Wiring for group controlled ( Looped ) light/ceiling fan/exhaust fan/call bell point ( With out independent switch etc.) with 2x1.5 sq.mm PVC insulated stranded copper conductor cable alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing in surface/recessed steel conduit as required. (Point shall be controlled / looped From existing point). Group - C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

S.P 5/6 amps, one way modular switch, ISI Marked

S.P 15/16 amps, one way modular switch, ISI Marked

5 pin 5/6 amps, modular socket Outlet, ISI Marked

6 pin 15/16 amps, modular socket Outlet, ISI Marked

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20/25 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps “C” curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing Brass Batten/ Angle holder including connections etc. as required.

DB SUBMAIN WIRING IN STEEL CONDUITS

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre

2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre

2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre

2 X 10 sq. mm + 1 X 6 sq. mm earth wire Metre

2 X 16 sq. mm + 1 X 6 sq. mm earth wire Metre

4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre

4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre

4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre

POWER SOCKETS

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection, painting etc.as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required.

FINAL DISTIRIBUTION BOARD

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator)

8 way Double Door

12 way Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way Double Door

8 way Double Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) asrequired . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

6 way Double Door

12 way Double Door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired.

Providing and fixing following rating and breaking capacity and 4 pole MCB with thermomagnetic release and terminal spreaders with cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

25-63A 16KA fixed thermal setting

IP BASED CCTV SYSTEM

Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS Vandal-proof, Network Dome Camera (1280 × 960) resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch, IR range up to 30 mtrs, H.264 / MJPEG, Dual stream, motion detection, Bit rate 32 Kbps-16Mbps, 3D DNR, DWDR, 12 VDC ± 10%, PoE , IP66, K-10, with fixed lens between (2.5 - 12mm), size of lens shall be as per site requirement & mockup. ONVIF, SIP, NMS, Profile S supported, connectors complete as required in dome shape fixed type for mounting recessed in false ceiling or mounted on wall complete as required.

Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS, Vandal-proof, Network Bullet Camera,(1280x960)resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch,, H.264 / MPEG4 , Dual stream, Bit rate 32 Kbps-16Mbps, Standard IP66, PoE , with Fixed Lens between (2.5 - 12mm), size of lens shall be as per site requirement & mock-up ,IR range Up to 50 mtr, motion detection, with ONVIF, SIP, NMS, Profile S supported, connectors complete as required IR Bullet fixed type for mounting on wall or surface mounted with back box and adapter plate complete as required.

Supply, installation, testing and commissioning of Professional Video management and recording software and hardware comprising 32Ch. NVR to record output of all cameras mentioned above in Item no 1,2,3 Third-party network cameras supported, H.264 Compression - Up to 5 Megapixels resolution recording, multiple Hard Disk 8 SATA with each having maximum storage capacity of 6 TB , as required for minimum 30 days recording required for recording when in 80% motion @ 720p 25 Frames per second(Real Time) or for recording when not in motion @720p 12.5 Frames per second, with RAID-5 Storage ,10/100/1000 MBps network interface with each NVR, 2 USB2.0, HTTP Networkable, backup by USB/DVDWR, required Client software included, 6 Nos Client licenses and required Camera licenses for each camera complete as required. All the components to be of same make as Camera.

Supply,installation,testing and commissioning of 32” CCTV colour LED screen including all accessories complete as required.

Supply, installation, testing and commissioning of Layer 3 switch HP/ Cisco make with 16 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required.

Supply, installation, testing and commissioning of Layer 2 switch HP/ Cisco make with 32 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required.

Supplying and installation of 19" 42U APW President Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required

Supply and Laying of Cat-6 Cable in existing conduits for Cameras

Supply and Laying of 3C-2.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply

Supply and Laying of 3C-1.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply

Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

20mm dia

25mm dia

32mm dia

UPS/INV/SOALR SYSTEM

1550VA sine wave inverEr input AC range.1fi)V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range - 10.5 to 14.2 efficiancv- 80%, protection-overload, Short circuit

Trolly for Double tubular Battery

200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991

3000VA sine wave inverter input AC range-1O0V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range -1.0.5 toL4.2, efficiancv- 80%, protection-overload, Short circuit

Trolly for Double tubular Battery

200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991

Supply,Installation, Commissioning & Training of 40 KWp Grid Connected Rooftop Solar Photovoltaic System based on heterojunction technology solar PV module as per requirment. including all expenses (to be borne by bidder) e.g. Air Fare, Local Transport, accommodation etc.

RISING MAIN

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 A 25kA SC for 1 sec

630 A 30kA SC for 1 sec

800 A 50kA SC for 1 sec

1000 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 1000 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required

125 A 15kA SC for 1 sec

250 A 30kA SC for 1 sec

400 A 35kA SC for 1 sec

PLUMBING/SANITARY WORKS

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing 15 mm dia male ended C.I .Body brass spindle valve and seat bib cock of approved quality (wt not less than 400 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing 15 mm dia male ended C.I push cock (wt not less than 400 gms) of approved quality with extra socket all complete as per specification and direction of E/l .

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l .

A) BRASS STOP COCK

(a) 15 mm dia

(b) 20 mm dia

Providing and fixing 15 mm dia and 45 cm. long P. V .C connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of E/l .

Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l. (b) C.I. body brass spindle

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 15 mm dia wt not less than 300 gms

(b) 20mm dia wt not less than 400 gms

(c) 25 mm dia wt not less than 500 gms

(d) 32 mm dia wt not less than 700 gms

(e) 40 mm dia wt not less than 1kg

(f) 50 mm dia wt not less than 1.5 kg

Cutting drain width wise above G.L for laying G.I pipes and restoring with brick in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.

(a) Mirrors of 6 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

(1)600x450 mm size

(2) C.P brass liquid shop container

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(B) 510 mm long

(a)12.5 lit. low level P.V.C. cistern

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.

(i) 125 mm dia

(ii) 250 mm dia

Supplying Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump ste shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run shall be provided with each pump.

Submersible pump set 50mm dia (with polypropylene/ Noryl Impeller) up to 20 stages 3 HP

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

40 mm dia

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. 110mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion.

Coupler 110 mm dia

Single Tee with door 110x110x110 mm

Bend 87.5 deg 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised- PVC pipe clip of approved desing to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwes with M.S. Screw of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 Cement : 4 Coarse sand ) and making good the wall etc. complete. 110mm dia

Providing and fixing white vitreous china battery based infrared sensor operated urinal of appx.size 610x390x370mm having pre & post flushing with water (250ml & 500ml consumption) having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturers specification & direction of Engineer-in charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

65 mm nominal bore

80 mm nominal bore

Providing and fixing C.P. bass angle valve of approved quality conforming to I.S:8931. 15 mm nominal bore

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m.

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia

Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete.

150 mm. dia. RCC Pipes

250 mm. dia. RCC Pipes

300 mm. dia. RCC Pipes

450 mm. dia. RCC Pipes

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

Construction brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes

Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

1.68 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square mouth SW gully trap class SP-1 complete CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.7 kg. as per standard design.100x100mm size P type

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Providing and fixing wash basin with CI brackets,15mm brass pillar taps,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required.

White vitreous china wash basin size 630 mm x 450 mm with a single 15mm CP brass pillar tap.

Constructing brick masonry road gully chamber 50 X 45 X 60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500 X 450 mm precast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S (non modular) bricks of class designation 7.5.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing G.I. pipes conforming to I:S including all fittings, testing, cutting holes or chases and making good where required. (For waste connections) 32mm dia

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 32mm dia

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia

Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing fixing, testing and commissioning in position SWR PVC PIPE TYPE-B pipe comforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offests, cowl, access pieces/clean out plugs, clamps /supports/ hangers etc. jointing with PVC Adhesive joints including cutting holes in walls, core cutting in slabs and making good the same. all complete as per specification and direction of E/l.

(a) 250 mm dia

(a) 150 mm dia

(c) 100 mm dia

(e) 50 mm dia

Providing & fixing in position uPVC P"or S" trap of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required.

3 x 50 mm inlet and 100 mm outlet (Multi Floor Trap)

50 mm outlet (Floor Drain)

Providing & fixing in position storage type hot water electrical geyser (vertical or horizontal-1.5 kw) including making connection in all respects.-Venus/Racold make.

15 litres capacity (Make: AO Smith)

25 litres capacity (Make: AO Smith)

Supply installation testing and commissioning R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 100 lph.-Kent/approved equal make.

Fixing of Wall Mounted C.P. Brass Single lever Sink Mixer with swinging spout of required size including cuttinig and making good the wall wherever required. (Make: Jaquar Sink Mixer CQT-23309)

Providing & fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. (Make: Jaquar, Hand Shower (Health Faucet) ALD-CHR-573 )

Providing & fixing chinaware urinal partition of 160X 400X 825 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete complete including cutting and making good the walls wherever required (Make: Parryware, white C0507 Large)

Providing & fixing soild state no touch operating fully highgenic SS hand drier of best quality, to be operated with 230 volts, single phase, with fully hygienic condition, with all accessories including cutting and making good the walls, wherever required. (Make:- Euronics, Stainless Steel Hand Dryer EH21)

Providing and Fixing in position Hindware make or equivalent CP Grab Bar with wall flanges 600 mm to wooden cleats with C.P. brass screws complete in all respects.

Providing and fixing C.P. brass twin coat hooks fixed on toilet door with including CP brass screws, washers rawl plugh etc. complete in all respact. (Make: Jaquar, ACN-SSF-1161N)

Supplying and fixing 100 mm dia SWR PVC End Cap (Clean Outlet Plug) fittings of approved make. all complete as per specification and direction of E/l.

Providing and fixing M.S. puddle flanges fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be painted with black Japan paint .

25 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

250 mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of engineer in charge.

150mm dia

200mm dia

Supplying and fixing 150 mm dia PVC End Cap (Clean Outlet Plug) fittings of approved make all complete as per specification and direction of E/l.

Sump Pump Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open impeller, suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following :

Complete inlet, outlet and header piping of suitable dia (velocity shall not exceed 1.5m/s) -- 1 Lot

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

Necessary cables from pump sets to pump starter panel - 1 Lot

Electrical control panel having all necessary accessories & safety devices of standard specifications and suitable for receiving incomer cable to connect complete. (Panels with sump pumps near each sump as per site conditions). -- 1 No.

Discharge :5 m3/Hr

Head : 25 m

Solid Handling : 50 mm

Pumps shall be operated on cyclic timing

The entire system along with pumps & control panel must be sourced from single manufacturer only for unit responsibility.

One set consist of 2 nos.of pumps - 1 working & 1 stand by (Complete set as above with 2 nos. pumps including cost for valves, piping, Control Panel and Cabling, Level Controllers, pressure gauges etc as required and as specified)

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

4.0Cx6 Sqm

4.0Cx10 Sqm

4C x 16 Sq. mm

Supplying, storing, handling, shifting, insatallation, testing and commissioning of 1 No. - 500 Litres (Make : A.O. Smith) floor mounted vertical type glass lined air heat pump technology hot water storage type electrical fired water heater with 1 No. hot water circulating pump (grundfoss make) in SS304 (@ 30m head), automatic thermostatic control electric element, pressure release valve, safety valve, all interconnecting pipes - SS-316 valves, accessories, pressure guage, thermometer, flow meter, brackets fixed to expansion fasteners with M.S. nuts and bolts, 25mm insulation with cladding complete including cutting and making good the walls wherever required.

Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia

Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser).

50 mm dia

65 mm dia

Constructing water tight brick masonry grease trap with first class bricks in cement mortar 1:6 (1 cement :6 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement & M.S. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), two brick masonry baffle walls each of 500 mm depth deep each of 115 mm thickness, 2 Nos C.I. double seal medium duty covers each of 450 x 450 mm size including excavation, backfilling & disposal of surplus earth with a lead upto 50m complete as per standard design. (Note: Cost shall include dewatering & water proofing of Grease trap as directed at site). Grease Trap (Size 1200 x 900 x 1000 mm overall depth).

Providing and fixing G.I. Vent Pipe class 'B' (medium duty) for R.C.C water storage tanks comprising of 600 mm long vertical pipe, return bend with mosquito grating & cast brass perforated coupling including all associated civil work. 100 mm dia

Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia

WATER SUPPLY

Excavating trenches of required width for pipes including excavation for sockets also including for cement concrete craddles, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer with minimum 95% by ramming, watering etc. and disposing off surplus excavated soil as directed, within a lead of 50 m. UPTO 1.5M Pipes, cables etc, not exceeding 80 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge.

Internal Work - Exposed on Wall

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

40 mm nominal outer dia pipes.

50 mm nominal outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

25 mm nominal outer dia pipes.

32 mm nominal outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings. This including jointing of pipes & fittings with one step CPVC solvent cement , trenching, refilling & testing of joints complete as per direction of Engineer in charge.External work.

32 mm nominal outer dia pipes.

40mm Nominal outer dia pipes

50mm Nominal outer dia pipes

65 mm nominal inner dia pipes.

Fixing water meter and stop cock in G.I pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. [Location : From Bore Well/Tanker water supply line/Municipal line to Underground Water Storage Tank]. 80 mm dia

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),i/c necessary excavation foundation concrete 1:5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 Cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

(i) Domestic tank

(i)Flushing tank

(i) Fire tank

Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams with threaded end for hose connection.

Providing and fixing gun metal non- return valve of approved quality (screwed end).

50 mm dia nominal bore-vertical

65 mm dia nominal bore-vertical

80 mm dia nominal bore-vertical

Supplying and fixing C.I. cover without frame for manholes: 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 mm Thick

SEWAGE TREATMENT PLANT (75 KLD)

Design, supplying, installing, testing & commissioning of Sewage Treatment Plant

Nature of effluent - Domestic Sewage from Public toilets, Kitchen etc.

Daily average flow - 75 m3/Day

BOD5 - 250 – 350 Mg/L

S. Solids - 400 – 600 Mg/L

COD - 600 – 800 Mg/L

Oil & Grease - 50 Mg / L

Effluent discharge standard after treatment

BOD5 - Less than 10 Mg/L

S. Solids - Less than 20 Mg/L

COD - Less than 60 Mg/L

Oil & Grease - Less than 5 Mg/L

Sewage treatment plant shall include the following items:

Screen Chamber

Oil & Grease Chamber

Sewage Equalization Tank/Sump (1 No)

FAB Tank. (2 Nos)

Secondary Tube Settler Tank (1 Nos)

Clarified Contact Tank

Sludge Holding Tank

Air Blowers, Pumps & equipment

Filter Press and Feed Pump

Piping, valves etc

Electrical Panel & Cabling

Common plant room adjacent to STP.

Ultra filtration Plant (OPTIONAL

Supply, installation, testing & commissioning of 2 Nos Stainless Steel Bar Screen with suitable lifting arrangement (size 600 mm wide x 800 mm high approx)

Supply, installation, testing & commissioning of electronic type level indicator and controller for automatic operation of the system with high/low level complete with auxillary NO/NC contacts.

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned component and additional component if so required for the complete working of the STP and got it approved by the Owner’s Architect/Project Manager/Consultants. .

Supply, installation, testing & commissioning of non clogging type pumps capable of handling solids upto 30-35 mm having CI casing & impeller complete with all accessories, motor of required capacity. Delivery header with isolation valve on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Pumps shall have following duty (At EQT. Tank)

Submersible Sump Pumps 1 Set = 2 Nos (1W + 1SB)

Flow rate (each) = 5 m3/hr

Head = 8 - 10 Mtr

Make: WILO / Kirloskar/ KSB

Plant room sump pump with CI body & CI impeller pump

Flow rate (each) = 7 m3/hr

Head = 10 - 12 Mtr

Make: WILO / Kirloskar/ KSB

Horizontal Self Priming Sludge Recirculation pump with CI body & CI impeller pump

Flow rate (each) = 5 m3/hr

Head = 10 - 12 Mtr

Make: Kirloskar / M&P

(Solid handling size for this pump shall be 7 mm).

Cost shall be inclusive of PVC flexible Hose pipe ( for piping submeged in effluent) with M S epoxy piping (for piping non-submerged in effluent)

Provision of guide ropes to guide submersible pump from upper level to operational level in sump basin with channels / angle section shall be made by the STP contractor.

Air diffusion system shall include the following:

Twin lobe rotary air blowers capable of delivering 110 m3/hr. of free air at 5 Mts. driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. (1W + 1 SB)

Make: Beta / Everest/ Akash

Air piping shall comprise of pipes droppers / laterals with SS 304 Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good. Contactor to submit detailed P & I indicating their proposal

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top.

Make: Welcome/MM Aqua/W2P

Bronze Ball valve and air dispersion grid as required for STP as described above.

Supply, installation, testing & commissioning of PVC FAB media in FAB Tank & PVC Tube Deck media Secondary Tube Settler Tank.

Providing and fixing all piping (as described below) and isolation control valves for making the system complete.

uPVC : Submerged air piping

MS Epoxy : Air piping

uPVC Piping : Pumped effluent & tank overflow pipe line

uPVC Piping : Interconnecting pipe line after delivery

header of pump/ filter

Supplying, installing, testing & commissioning of Horizontal centrifugal pumps CI Body, Bronze Impeller, SS Shaft, with mechanical seal along with Coupled motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer at suction. Mechanical seal. The pump shall be suitable for 415±10% volts 3 phase AC supply.

Filter Feed Pump. (1W + 1SB)

Capacity : 7 m3/hr

Head : 30 - 35 M

Make : Kirloskar / M&P

Operation of pump shall be based on level controller proposed to be installed in tank as per site location. The contractor to recheck the Head required for pumps as per site conditions and provide accordingly.

Supplying, installing, testing and commissioning of dosing system consisting of one HDPE tank of 100 litres capacity with a positive displacement diphragm dosing pump having variable flowrate of 0-12 lph. The motor shall be suitable for operation at 240 V/single phase/50 Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, valves, strainers, low level switch and injection fittings. The pump shall be speed & stroke control. Make: Toschon/Asia LMI/equivalent make.

Supplying, installing, testing and commissioning of MS epoxy coated vessel filter. Filter shall be suitable for working pressure of 3.0 kg/ cm2 and shall include media, standard fittings like pressure gauges, sampling cock, backwash, rinse drain, including frontal piping.

Multigrade pressure sand filter

Flow rate : 7 m3/hr

Dia : 850 mm

Activated Carbon Filter

Flow rate : 7 m3/hr

Dia : 850 mm

Supplying, installation & commissioning of Filter Press

M.O.C. : MS

Plates : 24

Filter cloth : PP Bag

Make : Airtech / W2P

Supplying, installation & commissioning of screw pump of capacity 1.0 m3 / hr. at 10 mtr. Head ( 1 W )

Make: Roto

Supply, installation, testing & commissioning of Ultra voilet syetm for disinfection. UV doses should be >60000 m W-sec/cm2. Make : Alfa / Sukarati

Flow- 7 m3/ hr.

Control Panel for Sewage Treatment Plant

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre shall be fabricated out of 14 gauge CRCA sheet steel in form in 3 formation with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanised hardware with zinc passivation shall be used in fabrication of panels.

MCC-1 (STP Motor Control Centre)

Incoming

100 amps TPN MCCB with the following accessories:

Phase indicating lamps shall be protected by 2 amp SP MCB 3 Sets

Bus Bar

100 amps TPN (25 KA) copper bus bar with heat shrinkable insulation sleeves.

Outgoing

As per the STP equipment rating

Make: Enweco

MAINTENANCE CONTRACT

To operate the entire STP under available load conditions for further period of 30 days on round the clock basis.

To provide services of contractors expert operating personal comprising of :

One Supervisor Three times a week.

One Plant operator around the clock.

One helper for general maintenance and assistance. One per shift in three shifts.

Company’s back up services of senior engineers and experts for any major problems, general check up and maintenance and advise. Once a week.

All tools, equipment and testing devices to be provided by the contractor.

Consumable including lubricants and chemicals will be provided by Owners.

Ultra Filtration Unit with Membrane Module and allied Pumps, dosing pumps, backwash pumps, High Pressure Pumps,motorised valves and automated Panel with PLC,

WATER TREATMENT PLANT/ WATER SUPPLY/DRAINAGE/SEWAGE PUMPS WORKS

WATER SUPPLY/DRAINAGE & SEWERAGE SUMP PUMPS :

Fixed Speed Hydropneumatic System FOR Over Head Storage Tank Filling Pump :

Supply, Installation, Testing & Commissioning of Factory assembled Compact self contained Hydropneumatic system comprising of following :

Vertical, In-line, multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-316 shaft, C.I. Base & head TEFC motor (with mechanical seal) Vendor to submit performance curves, dimension detail and technical catalogue of the proposed model for review and approval.

Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be of suitable capacity or as per manufacturer calculation / recommendation).

Set of accessories such as pressure switches, pressure transducers,valve (butterfly / ball valve, NRV of PN 10.00 rating) Vibration Isolator, GI "heavy class" suction & delivery header & interconnection piping, level controller, pressure gauge inter connecting power and control cabling etc. complete with Vibration eliminator of required quantities,Bypass arrangement etc.

DOMESTIC WATER LIFTING PUMPS :

Capacity /Flow rate : 10.0 M3/ Hr

Pumping Head : 60 m

Power Requirement (kw) : 3.8 KW or as per manufacturer recommendation

Location : Water Treatment Plant Room

1 Set = 2 Nos. Pump (1 Working+1 Standby)

Supply

Installation, testing & commissioning

FLUSHING WATER LIFTING PUMPS :

Capacity /Flow rate : 10.0 M3/ Hr

Pumping Head : 60 m

Power Requirement (kw) : 3.8 KW or as per manufacturer recommendation

Location : Sewage Treatment Plant Room

1 Set = 2 Nos. Pump (1 Working+1 Standby)

Supply

Installation, testing & commissioning

Water Supply Pumps :

Supply, Installation, Testing & Commissioning of Single Stage/Multi stage Horizontal / Vertical centrifugal monobloc pumping set with delivery SS 304 body and SS 304 impeller, shaft of stainless steel SS 316 and SS shaft sleeve C.I. Base & head, mechanical seal, connected to a TEFC induction motor suitable for 400/440 volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, level controller, vibration eliminating pads as required, M.S fabricated base plate bolted to cement concrete foundations complete.

FILTER FEED PUMPS :

Capacity /Flow rate : 37.5 M3/ Hr

Pumping Head : 30 m

Power Requirement (kw) : 7.46 KW or as per manufacturer recommendation

Location : Water Treatment Plant Room

1 Set = 2 Nos. Pump (1 Working+1 Standby)

Supply

Installation, testing & commissioning

Drainage Pumps :

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical. discharge pipe, in built level controller with operational moded as one pump working at low level, pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length cable etc. as per requirement complete in all respects.

Pump shall be installed in a set of Two pumps (One Working and One Standby).

Plant Room Drainage Pumps [For Plumbing and Fire Fighting Pump Room ] :

(Pumps to be suitable to handle solids upto 10-12 mm size with CI/ body, S.S. shaft, CI/ impeller with cable, double mechanical seal).

Capacity/Flow Rate - 453 LPM (Each) (27.18 M3/hour)

Pumping Head - 10 m

Motor H.P - 3.0 HP (2.2 KW) (Approx)as per manufacturer recommendation

Location - (Plant Room)

1 Set = 2 Nos. Pump (1 Working+1 Standby)

Supply

Installation, testing & commissioning

Basement Drainage Sump Pumps :

(Pumps to be suitable to handle solids upto 10-12 mm size with CI/ body, S.S. shaft, CI/ impeller with cable, double mechanical seal).

Capacity/Flow Rate - 453 LPM (Each) (27.18 M3/hour)

Pumping Head - 10 m

Motor H.P - 3.0 HP (2.2 KW) (Approx)as per manufacturer recommendation

Location - (Plant Room)

1 Set = 2 Nos. Pump (1 Working+1 Standby)

Supply

Installation, testing & commissioning

Supply, installation, testing & commissioning of G.I. Pipes Class 'C' conforming to I.S. 1239 (Heavy grade) with G.I. Fittings conforming to IS : 1879 (Part I to X) such as tees, crosses, plugh, socket, elbows, reducers, flange, check nut, flanges & clamps, hanger, structural steel supports as required/directed at Site including cutting and making good the walls etc. complete

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Painting G.I. Pipes (heavy class) with two or more coats of synthetic enamel paint of approved quality and shade over a coat of approved priming coat as directed by the Project Manager (shade as per pipe colour code).

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Ball Valve:

Providing and fixing Ball valve with hard chrome plated ball inside PTEF (Teflon) seat & ring with chrome plated center handle with female BSP threads complete in all respect.

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supply, installation, testing & commissioning of CI dual plate type non-return valve (PN 10) complete with 2 Nos. matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes with locking arrangement.

50 mm dia

80 mm dia

Supply, installation, testing & commissioning of CI slim seal butterfly valves Class (PN 10) complete with 2 Nos. matching flanges rubber insertion, nuts, bolts and washer etc. of following sizes :-

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing & fixing resilient rubber neoprene lined style arch vibration eliminators suitable upto pressure 20 kg. /Sqcm.

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Providing and fixing C.I. Y type suction strainer with gunmetal or brass internal parts installed outside water.

65 mm dia

80 mm dia

150 mm dia

Providing & laying S & S cast spun pipes conforming to IS : 1536 class 'LA' including all fittings conforming to IS : 1538 e.g. bends, tees, reducers, blank flanges, drip seal/lead joints as per IS : 3114, effective proper connection (For Basement Drainage Line + Plant Room Drainage + Sewerage Room Drainage) complete i/c excavation/back filling, bed concrete, sand bed, painting two or more coats with synthetic enamel paint ovr a coat of primer.

80 mm dia

WATER TREATMENT EQUIPMENTS :

DUAL MEDIA PRESSURE SAND FILTER :

Providing, fixing, testing and commissioning of vertical self supporting dual media pressure sand filter vessel fabricated from MS sheet as per IS : 2825 (The filter shall be made of 6 mm thick shell & 8 mm thick dish end), pressure gauges at inlet & outlet, sample cock, air vent valve with piping, GI class 'C' face piping/distribution pipe with diffuser on top, CI butterfly valves and all accessories, with initial charge of filter media for dual media filter, painting inside with food grade epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint complete with bypass arrangement including pipe, fitting, accessories and 3 Nos. Isolation valve (in case of maintenance).

Dual Media , Pressure Sand Filter for Domestic Water Supply System:

Capacity - 37.5 m3/hour

Filtration rate - 15.0 m3/hr/m2

Filter dia (approx.) - 1800 mm dia

Working pressure - 3.0 Kg/Sq.cm

Test pressure - 5.0 Kg/Sq.cm

Location - WTP Plant Room

Supply

Installation, testing & commissioning

Activated Carbon Filter :

Providing, fixing, testing & commissioning vertical self supporting Activated Carbon Filter (ACF) fabricated from M.S. Sheet as per IS: 2825 (The filter shall be made of 6 mm thick shell & 8 mm thick dish end), pressure gauge at inlet & outlet, sample cock, G.I. Class 'C' face piping, C.I. Butterfly valve and all accessories, air vent valve with piping, with initial charge of filter media for activated carbon filter, painting inside with food graded epoxy paint and outside with two coat of synthetic enamel paint complete with bypass arrangement including pipe, fitting, accessories and 3 Nos. Isolation valve (in case of maintenance).

Activated Carbon Filter for Domestic Water Supply System:-

Capacity - 37.5 m3/hour

Filtration rate - 15.0 m3/hr/m2

Filter dia (approx.) - 1500 mm dia

Working pressure - 3.0 Kg/Sq.cm

Test pressure - 5.0 Kg/Sq.cm

Location - WTP Plant Room

Supply

Installation, testing & commissioning

Providing, fixing, testing & commissioning of metering pump type chemical doser with 100 lits.HDPE/ FRP solution tank, injection fitting assembly, suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects for treated water tank (Location : WTP Plant Room ).

Chlorination of Domestic Water :

Supply

Installation, testing & commissioning

UV Sterilizer:

Supply, Installation, testing & commissioning of online SS 316 UV Sterlizer suitable for UV Dosage >60000mw-sec/cm2 following flow rate. Complete with UV Intensitty Monitor all fitting & accessories, bypass arrangement including piping & 3 Nos. Isolation valve complete Maximum operating Pressure Shall be 85 Psi (Location : WTP Plant Room ).

Flow Rate 10 M3/hr

Providing, fixing, testing and commissioning of Fully Automatic micro-controller based water level Controller and Water-Level LCD Display & motor protector including sensor, Display Panel, cabling and all fitting and accessories (For Underground Water Tanks at WTP).

Supply, Installation, testing commissioning of Fully Automatic micro-controller based water level Controller and Water-Level LCD Display panel suitable to operate on the level of the tank including level sensors, 02 Nos. of float switches (For Overhead Water Tanks)

Solenoid Valve :

Supply, Installation, testing commissioning of solenoid valve suitable to operate 24V DC/50 HZ supply including all fitting and accessories (Location : Terrace).

40 mm dia for flushing and domestic water

50 mm dia

ELECTRICAL PANEL:

POWER AND MOTOR CONTROL CENTRES:

Design, manufacture, supply, installation, testing and commissioning of following MV switchgear panels suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting/wall mounted, sheet metal clad, cubicle.

All MCCBs shall be provided with magnetic & adjustable thermal releases for short circuit & overload protection with front drive kit (rotary operating handle).

NOTES :

The BOQ shall be read in conjunction with general notes, specification and Single Line Diagram (attached for Ref.). Incase of any discrepancy between specification, BOQ and SLD, the same shall be brought to the notice of Client/Consultant before quoting the rates, otherwise stringent condition shall be deemed to have been considered.

Fault current wherever mentioned shall be Ics value. (Ics = 100% Icu)

All MCCB shall be provided with door interlocked rotary handle with ON/OFF/TRIP position indicator, continious variable thermal magnetic O/C and S/C releases. The MCCB above 250A rating shall be provided with microprocessor based releases (settable at site). I/C MCCB shall be provided with E/F release/Earth Fault protection also.

All feeder doors shall have pad locking arrangement.

All TP/TPN feeders shall have solid isolable neutral link.

All MCCB used in starter feeder shall be suitable for motor duty application.

Spare contacts of ACB/Relays/Contactor etc. shall be wired upto terminal block.

All switchgear used in starter feeder shall be type-2 co-ordinated. Manufacturer is required to submit manufacturers type-2 co-ordination chart for the make used.

All outgoing terminals (power and control) shall be brought upto cable alley. 10% extra terminals shall be provided.

Removable lifting hook shall be provided in all transportation section.

All CT, PT shall be cast resin.

All meters are digital type and with RS-485 port.

Panel shall be powder coated of approved shade with minimum 60 micron thickness.

MCCB's/MPCB's/MCB's in one particular panel shall be of one similar make.

Size of Voltmeter / Ammeter for incomer also, 96mm x 96mm flush mounted with shrouded terminal shall be used in the panel.

Bus bar chamber shall be kept at top of the all panels.

All bus bar shall be insulated with coloured PVC Sleeve i.e.RYB,BK as per colour code.

Internal wiring of panel shall be with size 2.5sqmm FRLSH, Flexible Copper Conductor for CT circuit and control wiring with 1.5 sqmm.

All indicating light shall be LED type .

Each vertical section of floor mounted panel shall have independent base frame (75mm x 40mm) size made out of 3 mm sheet steel.

Wherever only voltmeter & ammeter are required, the same may be provided in combined meter suitable for both parameter.

All the makes shall be as per Client approved make list only.

All motor circuit MCB shall be motor duty with 'C' curve.

All power contactor shall be of AC3 duty.

All indoor Panel shall be IP-52 & outdoor Panel shall be IP-55.

Starter Control scheme shall be as per schedule #1.

WTP Panel :

Location: Pump Room

Comprising of the following:

Incoming:

One (1) No. 100A, 16 KA, 4P MCCB .

One (1) set of R, Y, B phase indication lamps and ON/OFF/Trip indication Lamps with control SPMCB.

Busbars :

150 A TPN Aluminium busbar insulated with heat shrinkable sleeves and shall be color coded.

Outgoings:

2 Nos. DOL Starters,(1 working+1 standby) suitable for 3.804KW motor, complete with suitable range of TP MPCB with thermal range as per Type-II co-ordination chart.(Hydropenumatic System domestic Water Lifting)

2 Nos. DOL Starters,(1 working+1 standby) suitable for 7.46 KW motor, complete with suitable range of TP MPCB with thermal range as per Type-II co-ordination chart.(Filter feed pump)

2 Nos. DOL Starters,(1 working+1 standby) suitable for 2.2 KW motor, complete with suitable range of TP MPCB with thermal range as per Type-II co-ordination chart.(Basement drainage pump-1 )

2 Nos. DOL Starters,(1 working+1 standby) suitable for 2.2 KW motor, complete with suitable range of TP MPCB with thermal range as per Type-II co-ordination chart.(Basement drainage pump-2 )

2 Nos. DOL Starters,(1 working+1 standby) suitable for 2.2 KW motor, complete with suitable range of TP MPCB with thermal range as per Type-II co-ordination chart.(Plant Room drainage pump plumbing & fire )

Water Level Controller with level switches :

Water level controller shall be provided for each starter with sufficient nos. of low/high level switches for the auto operation of the pumps. Cost for wiring from level switches to the starter panel shall be included in this item and shall not be paid separately.

Starter control scheme as per the Schedule # 1.

NOTES :

VFD shall be free supplied to the panel Manufacturer,by the Vender .

For space requirement of VFD , Panel manufacturer shall Co-ordinate with the Vender .

1No. 15A socket outlets shall be provided in WTP plant room for Each Dosing Pumps & UV units by electrical contractor

WTP Panel as described above and as per SLD.

Design, manufacturer supply & installation of mushroom head type Emergency stop/start push button with NC +NO contact in sheet metal enclosure.

Cables, Submains & Cable Trays:

Supply, installation, testing and commissioning of following sizes of PVC sheathed, XLPE insulated ,Aluminium /Copper conductor, power/control, armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required.

Aluminium Conductor armoured cables:

3.5 C x 50 Sq.mm

4 C x 10 Sq.mm

4 C x 6 Sq.mm

Cable Termination :

Supply & making end termination with brass Double compression glands for the following XLPE insulated PVC sheathed 1100 V grade cable including cost of crimping lugs/ ferrules, compression glands, solder, cable sockets, insulation tape etc. complete as required.

Suitable for aluminium conductor armoured cables:

3.5 C x 50 Sq.mm

4 C x 10 Sq.mm

4 C x 6 Sq.mm

Supply, installation, testing & commissioning of following sizes of ladder type GI cable trays with all necessary steel supports, fixing down rods, hardwares painting of supports in approved shade. complete in all respect. 300 mm x 50 mm x 2 mm

Supply, installation, testing & commissioning of following size G.I. Strip/G.I. wire clamped to existing cable tray, wall for system/equipment earthing complete as required including interconnection etc.

25 x 6 mm G.I. Strip

No : 8 SWG G.I. Wire

Water Feature 1:- Providing, fixing, testing & commissioning of Fountain

Providing, fixing, testing & commissioning of Nozzles

Supply, Installation, Testing & Commissioning of White ABS plastic bottom inlet 2" for concrete with S.S. screws and regulable .. Flow/ inlet = 9,000 l/hr.

Supply, Installation, Testing & Commissioning of Brass/ Gun Matel Geyser Jet 40mm Outlet Jet Nozzles Standard.etc., complete

Providing, fixing, testing & commissioning of Lights

Supply, Installation, Testing & Commissioning of SS 316 Niche Light 12V 15Watt RGBW (3watt x 5Nos Led) With Niche Standard etc., complete

Supply, Installation, Testing & Commissioning of Power Supply,

Supply, Installation, Testing & Commissioning of RGBW Controller,

Providing, fixing, testing & commissioning of Pump

Supply, installation, testing and commissioning of single stage/Horizontal Openwell submersible pump 5HP

Supply, installation, testing and commissioning of single stage/Horizontal Openwell submersible pump 1HP

Providing, fixing, testing & commissioning of Filter

Supply, Installation, Testing & Commissioning of TOTALLY ANTI- CORROSIVE Bobbin Wound filter,400mm diameter. Fitted with pressure gauge panel manual air bleeder, water drain and emptying plug.fitted with collector arms and diffuser made from unplasticizedPVC and polypropelene .etc., complete. Max.EN ISO 9001 :2000 Standard.working pressure : 2.5 kg/cm². Flow rate = 6m³/hr.

Sand for Sand Filter (SIZE 16/32 Mesh)

Providing, fixing, testing & commissioning of ChlorineDosing Unit

Supply, Installation, Testing & Commissioning of Online ChlorineDosing Unit for chlorine made in ABS Plastic

Providing, fixing, testing & commissioning of Control Panel (Equipments Make-L & T, Heger, Elmex, Rishabh, FTC, Esbee, Salzer etc.)

Supply & Commisioning of control panel complete as required. MCC(L&T)Relay(L&T)Push Bottom(Surdhi)Indicator(Surdhi)Auto Mannul Switch(Selzer) Contactors(L&T)as described above and below.etc., complete DOL Starter

Ammeter(Selec),Volt Meter(Selec),

Lugs, Wires, Enclosure, .

Centrifugal Pump and power supply and automation for pump

Providing & fixing of Wires/cables of various sizes including necessary accessories(Flexible Round Cable) as per Design

Wire 2.5mm Five Core (Round)

Wire 2.5mm Three Core (Flat)

Wire 1.5mm Three Core (Flat)

PVC Conduit 25mm

Providing and fixing of pipes (uPVC pipe- 10 kg. Pressure) & fittings (Heavy)

Providing & fixing of Valves, fittings etc of required size

FIREFIGHTING WORK

(WET RISER SYSTEM - PUMPING EQUIPMENTS)

Supply, Installation, Testing and Commissioning of Electric Driven Main Fire Pump suitable for auto operation & consisting of following: complete in all respect as required.The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% of the rated head. The shut off head shall not exceed 120% of the rated head. (Sprinkler & Hydrant Pump)

a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520.

b) Suitable HP squirrel cage induction motor, TEFC synchronous speed 2900 RPM (with permissible slip), suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, confirming to IS-325.

c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. The shut off head shall not exceed 120% of the rated head.

a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520.

b) Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system, fuel oil filter, lubricant oil pump with filter, 2 Nos. starting batteries of 180 AH capacity each with suitable angle iron stand, engine starting panel having all the controls meters, gauges, tachometer, hour meters, starting switch with keys for manual starting, auto starting mechanism, Including inbuilt electrical panel which will be activate by pressure switch, Including cables etc., 24 Volts electric starting equipment, Diesel Tank for 8 hrs continuous running of diesel engine, having minimum capacity of 200 Ltrs. (tank made out of 3mm thick M.S. Sheet with filling Cap, drain Cock, diesel indicator duly mounted on M.S. angle) exhaust pipe extended upto 1 mtr. outside pump house, duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, exhaust residential silencer, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

c) M.S. fabricated Common base frame, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation (minimum 6" above from ground floor) duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Supplying, Installation, Testing and Commissioning of Electric Driven Pressurization Pump (Jockey Pump) suitable for auto operation and consisting of following: complete in all respects as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head.

a) Horizontal type, centrifugal end suction type pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal, gland packing and flow of 180 Ipm at 88Mtr. head confirming to IS:1520.

b) Suitable HP (Minimum 4.0-5.0 HP) squirrel cage induction motor TEFC type 2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP-55 class of protection for enclosure, horizontal foot mounted type with Class - 'F' insulation, confirming to IS:325.

c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 6 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes

1.2 Meter high and 250 mm dia

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 8 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes

2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump , Sprinkler pump & Diesel Engine Driven Fire Pump

Supply, Installation, Testing and Commissioning of Electric Driven Main Fire Pump (Water Curtain System) suitable for auto operation & consisting of following: complete in all respect as required.The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% of the rated head. The shut off head shall not exceed 120% of the rated head.

Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 1.4 kg/sq. cm. at highest and farthest outlet at specified flow of 900 lpm at 50 Mtr. head confirming to IS 1520.

Suitable HP squirrel cage induction motor, TEFC synchronous speed 2900 RPM (with permissible slip), suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, confirming to IS-325.

(HYDRANTS SYSTEM)

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required.

Supply, Installation, Testing and Commissioning of 63 mm dia. 15 Mtr. Long RRL hose pipe with 63 mm dia. male and female stainless steel couplings duly binded with GI wire rivets etc. ISI marked, IS 636 (type-A) as required.

Supplying and fixing 63 mm dia. Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for instantaneous connections to hose pipe coupling etc. as required.

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required.

30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585

20 mm dia. ball valve & nozzle.

Drum and brackets for fixing the equipments on wall.

Connection from riser with 25 mm dia (Gun metal) stop valve & M.S. Pipe.

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following.

Gunmetal single headed Hydrant valve - 1 No.

Fire Hoses 63mm, 15 M long with accessories - 2 Nos.

Short branch - 1 No.

First Aid hose Reel - 1 No.

Fire Extinguisher - 2 Nos.

Fireman's Axe - 1 No.

Pressure Gauge - 1 No.

The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way - 100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

(PIPING, VALVES AND ACCESSORIES)

Supplying, laying, fixing, testing and commissioning of following sizes (NB) of class 'C' M.S. pipes confirming to IS 1239 and 3589 including cutting, threading, welding etc. and providing all fittings e.g. elbows, reducers, clamps, hangers, flanges, gaskets, nuts, bolts and washers etc. including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade including cutting holes and chases in brick or RCC walls/slabs and making good the same etc. complete in all respect as required. (The Welding shall not be done for piping less than 50 mm dia.)

200 mm dia (wall thickness 6.3 mm)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with EPDM rubber lining seat and CF-8 stainless steel disc duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required.

150 mm dia

80 mm dia

65 mm dia

Supplying and fixing Orifice Plate made of 6 mm thick, stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 Kg / cm2 complete as per specifications as required.

Providing, Installation, Testing and Commissioning of double flanged cast iron Dual Plat Check Valve (Non-Return Valve), PN 1.6 of following sizes confirming to IS : 5312 complete with EPDM rubber lining seat and stainless steel disc, rubber gasket, Gl bolts, nuts, washers etc. as required.

150 mm dia

65 mm dia

Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required.

150 mm dia

65 mm dia

Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications.

150 mm dia

65 mm dia

Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centrigade with required accessories :

Pendent Sprinkler

Sidewall Sprinkler

Upright Sprinkler

Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast irom body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulic driven mechanical gong bell to sound continous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency release, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice pate, gasket etc of following sizes as required 150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes coplete as required.

Supply, installation, testing & commissioning of deluge valve (to be used for curtains) UL listed with wet pilot basic trim assembly for DVA test and alarm, drio and drain valve with motor gong complete as required. 80mm dia

Providing, installation, testing & commissioning of water curtain nozzle 15mm dia nickle chrome plated brass, BSPT, K- factor as per design consideration complete as required.

Providing, installation, testing & commissioning of electric release trim assembly for deluge wall with two way solenoid valve, weather proof operation on 24 volts DC supply complete as required.

Providing, installation, testing & commissiong of adustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

(FIRE EXTINGUISHERS)

Powder Fire Extinguisher (Stored Pressure type) Capacity 09 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe locking arrangement, pressure gauge, operation manual and bracket. Operating Temperature: - 10ºC to + 55ºC. Brand LIFEGUARD

Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006 4.5kg capacity cylinder

Providing and fixing in position approved make fire bucket of 24 gauge, galvanized steel, standard 9 liters capacity and of round bottom shape, panted white inside and red outside and black on bottom dome with letters ‘FIRE’ in black and gold with all mounting bracket and screws.

Providing and fixing of fire Bucket Stand including sheet metal (16 gauge) shade for 2 buckets. Platform and associated civil works complete.

(MOTOR CONTROL PANELS)

Supplying, assembling, erecting, connecting, testing and commissioning of Outdoor type fire fighting double door lockable type with epoxy paint. This panel shall be mounting on MS/brick pedestal support upto 400 mm high from ground level,cubical, dust, vermin proof and outdoor type (IP65) fabricated as per specification laid in document with following incomming and outgoing feeders including making connections/inter-connections testing and earthing etc. required with necessary interlocking with existing panel as shown in drawing as per specification and mounted with the followings.

Incoming

1 No. - 630A 4P ATS

1 No. - 630A TPN MCCB of fault breaking capacity 50 kA (Ics = Icu upto 500V), fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with following accessories for each MCCB.

Independent electrical/manual spring closing mechanism - 1 No.

Microprocessor releases based relay(EMI & EMC certified) for over current, earth fault & short circuit protections with trip indications for each - 1 set.

Dual core calibrated digital Multifunctional meter of class 1.0 to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral) and 3 Nos. dual core CT of A Class 1.0 accuracy and 15 VA burden.

Following indicating lamps and push buttons for each MCCB with back up 2A SP MCB .

3 No. Phase indicating Lamps .

Indicating Lamps for the following;

Bus Bar

800 Amp. 50 kA, TPN Al. Bus Bar

Outgoings:

Following rated 420V,50KA MCCB's with overcurrent and short circuit releases Microprocessor based with ON,Trip indications, front operating handle & door interlock along with 2A SP MCB backup protection and control terminals & wiring as required. etc. complete in all respects as mentioned in specifications and as required For each outgoing:

125 Amp. TP MCCB -4 Nos.(4 spare)

16 Amp. TP MCCB -2 Nos.(2 spare)

The Panel shall have necessary arrangement to start the pumps at automatic mode in following sequence. a) The Jockey Pump is start to maintain the drop in pressure in pipe line and also in case of opening of any hydrant to maintain the required pressure. b) The main fire pump will start in case of jockey doesnot able to maintain the required pressure due to opening of any fire hydrant. c) To start the diesel engine operated fire pump in case of failure of power supply or in case of minimum fire pump is not able to required pressure.

(d) Diesel Engine Control

Control for Diesel Engine comprising:-

(ii) Indication lamp for High Water Temp. and Engine on indication and suitable tripping devices, overload, earth fault protection relays etc as required.

(iv) All standard relays and accessories for automatic operation of diesel engine.

(e) System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of Main Fire Pump, Pressurization Pump in sequence as per specification consisting of relays, timers, sensor, annunciation window for fault indication, complete as per specification.

Fire panel as above

ELECTRICAL CABLES

Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required.

PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1)

3.1/2 core 120sq. mm.

3.1/2 core 50sq. mm.

4 core 10 sq. mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required Upto 35 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 120sq. mm.

3.1/2 core 50sq. mm.

4 core 10sq. mm.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032)

100 mm. Width x 50mm. Depth x 1.6mm. Thickness.

150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop earthing along with the existing surface / recessed conduits / submain wiring / cable as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc, as required

HVAC WORKS

Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressors for above 14 HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410A Refrigerant,vibration isolators,with suitable foundation etc.complete as required.The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The unit shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.

Provision of power supply to each outdoor unit shall be provided with MCCB of suitable rating in IP 65 enclosure with suitable size of copper cable. Single source of power supply shall be provided by the client

40 HP OUTDOOR UNIT

28 HP OUTDOOR UNIT

26 HP OUTDOOR UNIT

24 HP OUTDOOR UNIT

22 HP OUTDOOR UNIT

20 HP OUTDOOR UNIT

LOW SIDE EQUIPMENTS

Indoor VRV Units (celling mounted ductable type unit)

Supply,installation,testing and commissioning of following minimum capacity 4-way flow VRV/VRF CassetteType Indoor ceiling mounted unit (Sensiflow Type ) equipped with synthetic washable media pre- filter, fan section with low noise fan/dynamically balanced blower,multi speed motor,coil section with DX Copper coil,electronic expansion valve,outer cabinet,drain pump,grill,necessary supports,vibration isolation,cordless remote control etc.,suitable for operation on single phase 230V±10%,50 Hz AC supply,complete,as required.The unit shall have automatic force shutdown provision in case of fire on receiving signal.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree DB and19 Degree C WB temperature

1x1.0 TR Four Way Cassette Type Unit (Sensiflow Type units )

Supply,installation,testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre - filter,fan section with low noise fan/dynamically balanced blower,multi speed motor,coil section with DX copper coil,electronic expansion valve,corded remote control,outer cabinet,vibration isolators,drain pan,other necessary supports etc.,suitable for operationon single phase AC supply 230V±10%,50Hz complete as required.The unit shall have automatic force shut down provision in case of fire on receiveing signal.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

1x1.28 TR/565 CFM Duct Type Unit

1x2.0 TR/688 CFM Duct Type Unit

Supply Installation, testing and commissioning of Y-joints of suitable size as per site requirements.

Supply Instalaltion, testing and commissioning of self diagnostic type remote controllers. Cordedless Type

CENTRALISED CONTROLLER

Supply testing and commissioning of main centralised controller as per specifications to hook up indoor units as mentioned . Controller shall have unified ON -OFF and schedule timer feature.Controller shall however, be suitable for minimum 64 groups of indoor units. Controller shall be suitable to autosequence the outdoor as well as indoor units catering to Server Room and UPS room as required.

Double Skinned Ceiling suspended/Floor Mounted Air Handling Units with thermal break profile with VFD

Supply, installation, testing and commissioning of factory fabricated Double Skinned DX TYPE Air- handling unit Floor Mounted/Ceiling Suspended fabricated out of extruded aluminium section with 0.63mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.63 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 Row DX type cooling coil made of Aluminium finned Copper tube with coil section,with following filtration level, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor and belt drive package etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 48 Kg/m³ density PU foam.The motor & blower assembly shall be mounted on Aluminium extruded section only

The face velocity across cooling coil shall be limited to 152 MPM maxm.

Pre-filter section with Pre filter(10 Micron & 90 % Efficiency) in All following AHUS

Expansion device with control box ,communication kit ,remote control & accessories for AHU kit

Fan Oulet Velocity Not to Exceed 8.5 m/s

6 RD Cooling Coil (CC)

CS AHU/1500CFM/3TR/50MM Static /6RD/1.1 KW

CS AHU/2000CFM/4TR/50MM Static /6RD/1.1 KW

CS AHU/2500CFM/4TR/50MM Static /6RD/1.5 KW

CS AHU/3000CFM/5TR/50MM Static /6RD/1.5 KW

CS AHU/3500CFM/11.5TR/50MM Static /6RD/2.2 KW

CS AHU/4000CFM/6TR/50MM Static /6RD/2.2 KW

CS AHU/4500CFM/8TR/50MM Static /6RD/2.2 KW

CS AHU/5000CFM/8TR/50MM Static /6RD/3.7 KW

CS AHU/5500CFM/9TR/50MM Static /6RD/3.7 KW

CS AHU/6000CFM/14.5TR/50MM Static /6RD/3.7 KW

CS AHU/6500CFM/11TR/50MM Static /6RD/3.7 KW

FM AHU/7500CFM/13TR/50MM Static /6RD/3.7 KW

FM AHU/12000CFM/26TR/50MM Static /6RD/5.5 KW

FM AHU/16000CFM/29TR/50MM Static /6RD/7.5 KW

FM AHU/19500CFM/34TR/50MM Static /6RD/11 KW

MECHNICAL VENTILATION SYSTEM

PROPELLAR FANS

Supply, installation, testing and commissioning of Propeller Type Heavy Duty Exhaust Fan complete with bird screen,gravity louvers, metal clad MCB & starter,5m length copper cable, earthing wire all compete as required, suitable for single phase, 230 volts, 50Hz AC. supply of following capacities:

1x225 MM Dia Propeller Fan

1x400 MM Dia Propeller Fan

CABINET TYPE INLINE FANS FOR TOILET VENTILATION

Supply, installation, testing and commissioning of ceiling suspended Inline fans (Rectangular/Round casing) complete with bird screen, rain guard, metal clad MCB & starter ,5m length copper cable, earthing wire all compete as required of following capacities as per specification and shop drawing mentioned.

500 CFM Inline Fan /Exhaust Air /Normal Mode /0.7KW

1000 CFM Inline Fan /Exhaust Air /Normal Mode /0.7KW

TUBE/VANE AXIAL FLOW FANS FOR NORMAL AS WELL AS FIRE MODE (FRESH AIR FAN) WITH STATER PANEL

Supply, installation, shifting, loading, unloading, testing & commissioning of floor mounted, double flanged, long casing (motor should completely accommodated inside the Fan casing) axial flow fans confirming to BSEN12101 standard (Fire Rated) AMCA Certified (all offered pitch angle certified by AMCA and listed on AMCA website), with adjustable pitch blade at site & angle (Welded Blades shall not be acceptable), bird screen at fan outlet , MS/GI casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4/6/8 pole, three Phase, A.C supply class "H" insulation with support, Phase& Motor rated Value IP55 . Motor shall be Thermally Rated for 240 deg C for 2 Hours & direct driven for smoke extraction fans.

With the Approx. Motor HP as given below (to be supported with Documentary evidence at the time of Technical Bid.)

Normal application fans should be "Vane Axial" type.

The rate shall include supply and fitting of vibration isolators ( spring & rubber pads) complete as per specifications and drawings including fitting of accessories like Fire retardant canvass connection painting,bird screen etc. as required at site of work. Including all type of civil work like cutting/holes/chasing/cut out in brick wall etc

1. Outlet Velocity for normal fans not to exceed 17.0 MPS

2. Total efficiency of normal fans shall not less than 60%

3. Fan motor shall meet IE3 standard as per IS-12615

AXIAL FAN/FRESH AIR /9000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/FRESH AIR /30500 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/FRESH AIR /7000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /9000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /14000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /17000 CFM /5.5 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /17500 CFM /5.5 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /19500 CFM /5.5 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/FRESH AIR /30500 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

TUBE AXIAL FLOW FANS FOR NORMAL AS WELL AS FIRE MODE (EXHAUST AIR FAN)

Supply, installation, shifting, loading, unloading, testing & commissioning of floor mounted, double flanged, long casing axial flow fans confirming to BSEN12101 standard (Fire Rated) AMCA Certified, with adjustable pitch blade & angle, bird screen at fan outlet , MS/GI casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4/6/8 pole, three Phase, A.C supply class "H" insulation with support, Phase& Motor rated Value IP55 . Motor shall be Thermally Rated for 240 deg C for 2 Hours & direct driven for smoke extraction fans.

With the Approx. Motor HP as given below (to be supported with Documentary evidence at the time of Technical Bid.)

The rate shall include supply and fitting of vibration isolators ( spring & rubber pads) complete as per specifications and drawings including fitting of accessories like Fire retardant canvass connection painting,bird screen etc. as required at site of work. Including all type of civil work like cutting/holes/chasing/cut out in brick wall etc

1. Outlet Velocity for normal fans not to exceed 17.0 MPS

2. Total efficiency of normal fans shall not less than 60%

3. Fan motor shall meet IE3 standard as per IS-12615

AXIAL FAN/EXHAUST AIR /9000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/EXHAUST AIR /30500 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/EXHAUST AIR /41000 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

AXIAL FAN/EXHAUST AIR /14000 CFM /3.7 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/EXHAUST AIR /17000 CFM /5.5 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/EXHAUST AIR /17500 CFM /5.5 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/EXHAUST AIR /30500 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

AXIAL FAN/EXHAUST AIR /41000 CFM /11 KW /30 MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /FIRE MODE

Supply,installation,testing and commissioning factory fabricated double skin exhaust/Fresh air unit comprising of 1No.DIDW GI fan & motor,forward curved, complete with base frame,casing made out of 0.63mm galvanised sheet having flanged & bolted panels insulated with PUF injected between outer skin and inner skin.The exhaust air unit shall be complete with motor, belt drive package of the following capacities.

DIDW/EXHAUST AIR /15000 CFM /3.7 KW / MM/ Not exceed 70 db. at 3 meter distance /3 PHASE /NORMAL MODE

JET FANS WITH CFD ANALYSIS

Supply ,installation ,testing & commissioning of Ductless Ventilation / Jet fans as per attached specifications for normal ventilation suitable for Normal ventilation and Smoke Extraction application in case of emergency i.e. 300 Deg C / 2 Hrs operation. Each fan shall be complete with motor and impeller. The Casing of fans shall be made of hot dipped Galvanized steel. The complete fan assembly with its Casing, impeller & motor (not only the motor or one of the item) shall be certified as tested for 300 Deg C for 2 hours operation' Jet fan silencer should be detachable type to ease of maintenance purpose and noise should be cerified from AMCA after Jet fan silencer. The Motor shall be suitable to run on 3 phase/50 hz/ 415 v electrical power. The CFD Analysis shall also be submitted by the Vendor at the time of installation to varify the qty and location of jet fans.

Jet fan should be certified from AMCA for AIR & SOUND performance

400 mm Dia. Jet fan

Motor : as per data

Mounting : Ceiling Suspended

Installation along with Anchor Fashioners (Hilti)

Supply ,installation ,testing & commissioning CO-Sensor confirming to UL & NFPA standard

Electrical Panel for jet fans PLC cum control panel

Supply ,installation ,testing & commissioning of BMS compatible power and control panel with all necessary control logics and software feeding the exhuast and the jet fans

Shall give power and control the Jet Vent fans, main exhaust and fresh air fans, CO SENSORS suitable for 30-90 ppm at pollution mode low speed. At 100 ppm and above and smoke mode during emergency system should run at high speed. Otherwise full system will run at the cycles mode

Should have the provision for hooking up the panel with fire fighting panel in case of emergecny

Should have the provision for monitoring the whole system through BMS

PIPING WORK

Supply,Installation,testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/harddrawn copper refrigerant piping for VRV/VRFsystem,complete with fittings,with suitable adjustable ring type hanger supports,jointing/brazing including accessories,insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines,all accessories as per specifications etc. as required :

41.27 mm dia(OD) (Hard drawn) with tube thickness 1.62 mm with19 mm thick insulation

34.9 mm dia(OD)(Hard drawn) with tube thickness1.62 mm with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with19 mm thick insulation

Supply, installation, testing and commissioning U-PVC pipe with fittings of 10 kg /cm3. with 6mm thick Nitrile rubber of Class "1" including all fittings and jointing with solvent cement and , including cutting chieseling / holes in walls ,wherever required and making good the same, complete as directed by the Engineer in charge.

25 mm dia pipe

32 mm dia pipe

AIR DISTRIBUTION

GSS RECTANGULAR DUCTING

Supply, Installation, Balancing & Commissioning of factory fabricated GSS sheet metal ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc finally applying fire rated paint as per BS 476 Part 24 . as per approved drawings and specifications of following sheet thickness complete as required.

splitter & vanes etc .shall be apart of ducting no extra cost shall be paid for the same .

0.63 mm sheet duct

0.80 mm sheet duct

1.0 mm sheet duct

1.25 mm sheet duct

Supply, Fabrication, installation and testing of GSS sheet metal ducts & finally applying fire rated paint as per BS 476 Part 24 (Site FABRICATED DUCTS For Connection /Plenum etc.) in accordance with the approved shop drawings complete with all accessories like vanes, flanges, suspension rods , anchor bolts, GI bolts & nuts, etc., as per specifications.

0.63 mm sheet duct

0.80 mm sheet duct

1.0 mm sheet duct

1.25 mm sheet duct

Supply, fabrication, installation and testing of 50 micron powder coated, aluminum extruded linear fixed horizintal bar/grill or diffusers with all side flanges as per approved shop drawings.

SSupply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.(18G)

Supply, Installation and Testing of 50 micron powder coated, Al extruded volume control damper for collor to be provided with suitable links and quadrants for control of volume of air.

Supply, fabrication, installation and testing of 50 micron powder coated, aluminum extruded fresh air louvers with bird screen & Al volumne control damper with all side flanges as per approved shop drawings.

Fire Dampers

Supply, installation, testing & commissioning of Duct/Wall mounted multi blade, motorised fire & smoke dampers with spring return actuator. The damper shall be of atleast 1.5 hr. fire rating and actuated with the help of 24 V electric actuator excluding. The damper shall be as per UL listed UL 555; 1995 and CBRI approved. The damper shall be constructed out of 16G galvanised steel sheet & as per specification with Control Cable to Potential Free Contact for tripping of AHU fan motor.

Damper Actuator

Supply, installation, testing and commissioning of Motorised Spring Return Actuator for devices upto 0.8 sq. metre with with control panel & temperature sensor.

INSULATION WORK.

Supply and installation of Insulation material shall be closed cell flexible elastomeric foam based on synthetic rubber composition with fire retardant properties.The insulation material shall have Microban®* an anti-microbial product, which is EPA (Environmental Protection Agency), USA Approved, as an integral part of insulation that cannot be washed off or worn off. The insulation material shall give enhanced level of protection against harmful Microbes such as fungi, bacteria & mold and should confirm to UL 181, ASTM G 21/C 1338. Thermal conductivity of insulation material shall not exceed 0.036 W/(m.K) at mean temperature of 24C as per ASTM C 177 / ASTM C 518. Water Vapor Permeability of insulation material shall be minimum 0.05 Perm-in. /0.725 x 10-13 Kg/[s.m.Pa] without any external barrier as per ASTM E 96. Procedure A. The insulation material shall have water absorption of 0.2% by volume as per ASTM C 209 / ASTM C 1763. The insulation material shall have fire performance rating of 25/50 as per ASTM E 84. The insulation material shall have fire performance rating of UL 94. The insulation material shall be self-extinguishing, does not drip, and does not spread flames. The insulation material need to comply with local Civil defence authority norms & should possess a valid approval. The insulation material shall be dust and fibre free. The insulation material shall be formaldehyde free. The insulation material shall be CFC & HCFC free. The insulation material shall meet ASHRAE 90.1-2010, ASHRAE Standard 189.1, NFPA 90A & NFPA 90B Standards. The insulation material shall withstand maximum surface temperature of +105 Deg.C and minimum surface temperature of -50 Deg.C as per ASTM C 534. The insulation material shall have ODP (Ozone Depletion Potential) and GWP (Global Warming Potential) of Zero. The insulation material shall be applied indoors. Coverings shall be used for exposed areas. Thickness of the insulation shall be as specified for the individual application. The insulation material shall be installed as per manufacturer’s recommendation.

13 MM Thick

ACOUSTIC INSULATION - FOR DUCT

Supply and Application of Acoustic Insulation Inside the Duct with Engineered Nitrile Rubber open cell foam with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7 and with built-in EPA approved Microban antimicrobial protection; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents. , Metal Strips and Anchor Fasteners as per design. 15 mm thickness (Internal Lining of Ducts)

CUBICAL PANEL BOARD

CUBICAL PANEL BOARD WITH WEATHER PROTECTION FOR FOLLOWING EQUIPMENTS:

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Ground Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

3.0 HP Fan Motor Nos 15

5.0 HP Fan Motor Nos 06

7.5 HP Fan Motor Nos 4.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

First Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

3.0 HP Fan Motor Nos 13

5.0 HP Fan Motor Nos 04

7.5 HP Fan Motor Nos 2.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Second Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

3.0 HP Fan Motor Nos 15

5.0 HP Fan Motor Nos 05

7.5 HP Fan Motor Nos 2.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Third Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

3.0 HP Fan Motor Nos 27

7.5 HP Fan Motor Nos 2.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Forth Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

3.0 HP Fan Motor Nos 17

5.0 HP Fan Motor Nos 3.0

7.5 HP Fan Motor Nos 2.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Fifth Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

5.0 HP Fan Motor Nos 6.0

7.5 HP Fan Motor Nos 4.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Sixth Floor

INCOMER

Sections of 180 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

1.5 HP Fan Motor Nos 1.0

2.0 HP Fan Motor Nos 1.0

3.0 HP Fan Motor Nos 2.0

5.0 HP Fan Motor Nos 6.0

7.5 HP Fan Motor Nos 1.0

15 HP Fan Motor Nos 1.0

7.5 HP Fan Motor Nos 6.0 For smoke extraction fans

Design, manufacture, supply, installation, testing and commissioning of the following 2 mm thick sheet steel enclosed separate compartment for each feeder, front operated, indoor type LT motor control panel, dust and vermin proof, /hinged and lockable doors, complete with internal wiring, colour coding with ferrules, cable glands plates, bonding to earth and painting etc as required.

Terrace Floor

INCOMER

Sections of 80 Amps TPN bus bar chamber of suitable lengths with Aluminium bus bars. All bus bars and interconnections shall be of suitable size Al strips. Current density of Al shall not be more than 1.0 Amps/ sq.mm cross sectional area of Bus Bar

OUTGOING

10 HP Fan Motor Nos 2.0

5.0 HP Fan Motor Nos 8.0 For Lift well and lobby

15 HP Fan Motor Nos 1.0 for Staircas e

POWER CABLING

Supplying, laying, effecting proper connections, testing & commissioning of the following sizes of 1.1 KV -Cross Linked Poly Ethelene armoured aluminium conductor cables conforming to relevant latest amended Indian Standards laid over MS supports & Cable Trays including clamping the cables to supports in an approved manner as required complete with all accessories.

3.5 Cx 25 Sqm Al Conductor

4.0Cx6 Sqm

4.0Cx10 Sqm

4C x 16 Sq. mm

COPPER POWER & CONTROL CABLING INCLUDING CABLE TRAY

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

3C x 1.5 sq. mm

3C x 2.5 sq. mm

3C x 4 sq. mm

Earthing Strip / Wires.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supply & laying 25x5mm GI strip at 0.5mt below ground as strip earth electrde including connection/terminatng with GI nut,bolt,spring,washer etc as required.)jointing shall be done by overlapping &with 2sets of brass nuts bolt&spring washer spaced at 50mm) 25mm x5mm

SPLIT AC

SITC 1.5Tr. 5 Star split A.C (Inverter Type) IS-1391-part-1

SITC 2.0Tr. S Star Split A.C (hiverter Type) IS-1391-part-l

Copper Tube of size l I 4 '' for split ac unit 1 /l.5/2/3 tr capac:ty nitride rubber insul;1tion

4 KVA wall mounted .:iutom;ltic voltage STABLIZER from range HOV to 28OV

Drain pipe for ac

Outdoor stand for 1.5Tr Split AC

Outdoor stand for 2.0Tr Split AC

BUILDING MANAGEMENT SYSTEM

CENTRAL CONTROL STATION

SITC of BMS Computer System: i7 Processor or Equivalet Server PC, Intel(R) Xeon(R) Processor, 2.93GHz, 4MB Cache with 16 GB RAM, 256 GB SDD, 1 TB HDD, 2 GB Graphics Card, 10/100 Mbps Ethernet card, USB connection & internal modem, Web server software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and anti virus software as per Tender Specifications. Accessories included Wireless Optical Mouse & Key Pad, with the above BMS System configuration. MS Windows 10 Enterprise or latest Licensed software compatible with the BMS platform etc. complete as required. Makes (Dell/HP/Lenovo)

Laserjet A4 Color Printer

APPLICATION SOFTWARE

Supply, installation, testing and commissioning of the following window based graphical software for IBMS system with 1 No. Client for Operator workstation. The Software shall have 3D & HD vector dynamic graphics with Autocad import of plan with Zoom In & Zoom Out facility, Native 64 Bit System, Multi-Monitor Support-( Max 4 Nos), Multi-language support, BTL, UL, EN Certified System, BACnet Profile B-AWS (Advanced workstation) as per the BTL Listing, dot net platform, Certified OPC DA Server by OPC Foundation, Web-Based Server software shall permit use of Standard Web-Browsers such as Microsoft Internet Explorer, Netscape Navigator, etc. The Software shall comply to international standards and strive to deliver products that meet security standards such as ISA/IEC 62443, UL2900, ISO/IEC 27001, ISO/IEC62443 and OWASP. Cybersecurity audit trail, 4-eye principle, Seamless integration of certificates within customer IT infrastructure, Microsoft’s active directory-based authentication, Use of network infrastructure that supports physical network or VLAN segmentation, Placing the web server in a “demilitarized zone” (DMZ), End-to-end encryption, from client to server, End-to-end encryption between servers, Certificate-based data exchange, Encrypted backups. Special Note - The Software should have cloud connectivty and can be access remotively using User Name and Password from anywhere. For further compliance vendor to follow the Tender specifications

INTEGRATORS

Supply, installation, testing and commissioning of True IP Based BTL & UL Listed for third party integration. The controller shall have 2-port Ethernet switch, WLAN interface and Cloud Connectivity. It should have BTL label (BACnet communications passed the BTL test) and consisting of Dual microprocessor with Storage capacity of 1 GByte RAM. It should support Real Time clock upto 7 Days. It should Support of the major communication protocols: BACnet/IP, BACnet MS/TP, Modbus IP and Modbus RTU upto 500 points. (Note - Integrator shall be of same DDC make only.)

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required. Number of controllers shall have spare capacity of 10% for future expansion.

For VRV System on Bacnet/IP

For VFD's on Modbus RS485

DDC CONTROLLERS

Supply, installation, testing and commissioning of True IP Based DDC Standalone 32 Bit Intelligent, inbuilt web browser, peer to peer communication, interoperable DDC as per the specification. The controller shall have inbuilt 2-port Ethernet switch. The DDC shall have 300 Mhz processor with 128 MByte SDRAM (DDR3) and 512 MByte NAND Flash. The DDC shall have IT security including HTTPS and BACnet Secure Connect communication, Operating voltage AC 24 V. The controller shall be freely programmable and have System functions (alarming, scheduling, trending, access protection with individually definable user profiles and categories). Each DDC shall have WLAN interface for local operation, engineering and commissioning. It should have one integration port inbuilt and port for POT for local interface. For further compliance vendor to follow the Tender specifications .

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required. Number of controllers shall have spare capacity of 10% for future expansion.

Controller for Common indication

Controller for CS & FM AHU system (2 AHU per DDC)

Controller for Ventilation Fans ( 4 Fans in 1 DDC)

Controller for Pressurisation Fans ( 4 Fans in 1 DDC)

FIELD INSTRUMENTS

Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters. The DDC shall support sensor with DC 0...20 mA or 4...20 mA, DC 0 ... 10 V, LGNi 1000, 2x LG- Ni1000, Pt 1000 , NTC 10k, NTC 100k, 1000 Ohm.

Combined Ambient air temperature + humidity, CO2 sensors with Display.

Differential pressure switch Air

Duct Temperature sensor

CO Sensor

IAQ (PM2.5, PM 10, T + RH, VOC, CO2, noise level) Multi sensor with Display on BACnet/IP

Current Rely

Cable, Conduit and Cable Tray

Supply, Installation, Testing & Commissioning of the following cables, conduit and cable tray as per the specifications:

2 Core 1 Sqmm Annealed Tinned Copper, Twisted pair , Shielded Un-armoured cable for signal and power as per specifications

4 Core 1 Sqmm Annealed Tinned Copper, Twisted pair , Shielded Un-armoured cable for signal and power as per specifications

Cat-6 unarmoured cable with required jacks and points

25 mm MS Conduit including all accessories

HOT DIP GALVANISED GALVANISED PERFORATED TYPE CABLE TRAY

GI Flexible 25 mm

NETWORK SWITCHES

Supply, installation, testing and commissioning of Layer 2 unmanaged switch with 16/24 ports (RJ-45) port rack mountable, SMPS power supply. The switch to switch distance shall not exceed beyond 80 meters

AUDIO - VISUAL EQUIPMENTS / INSTANT DISPLAY /WRITING / INFORMATION BOARDS, AUDIO VISUAL ITEMS, ACOUSTIC SOLUTIONS AND ALLIED WORK

Providing and Fixing of Envirotech Systems Micro Perforated Acoustic Paneling (MICROPERF). MICROPERF Perforated Acoustic Panels are made of Micro Perforated Mica laminate Sheet and High Density Perforated WPC Boards with rigid fixtation can be installed over Wall. The MICROPERF Perforated Acoustic Panels top sheet will be of 0.80mm thick Mica laminate with Micro Perforation Punch (Micro Perforation Circular Dia 0.60mm at a distance of 03 mm c/c as per acoustic design and desired shade as per Engineer In charge/Architect’s approval. The Base Boards of MICROPERF having 10 mm Sloted perforation of 28% perforated area as per acoustic design, the acoustic panels to be backed with 120 GSM black acoustic Non woven fabric for best NRC value of 0.86. Base of the MICROPERF panels is made out of 16mm thick WPC board. Size of the MICROPERF Panels 595x595mm, 600x1200mm, 600x2420mm with square edge as per acoustic design. MICROPERF Acoustic Panels can be fixed on GI Channel grid/extruded aluminum keel and inside clip system/ direct screw as per the instructions lay down by the manufacturer. Cavity of grid shall be filled with 50mm thick Acowool for noise absorbent value of 0.86 and Water Resistant, Termitre Resistant, Class A fire rating. The Panels colour as per Consultant / Architect’s approval. Preferable Make : Envirotech; Sun India , Tarel

Wall Paneling above the 8ft Height to false ceiling height

Providing and Fixing of Envirotech Systems Acoustic Glass Fiber Fabric Wall Paneling (FABLAM) Acoustic panels of Square, Rectangular shapes as per Architectural intent for following specifications : Acoustical panels shall be constructed of 25 mm in thickness in Square Edge profile with mica laminate fixed edge treatment. Fabric Finish of approved color and shade shall be applied directly to the face and edges of the panel and return to the back of the panel, Minimum of 30mm+ to provide a full finished edge. All corners are fully tailored. Acoustical Wall Panels shall have a NRC value of 1.0 in accordance with IS:8225/ISO:354/ASTM 423C/TRN38/13-14, Mounting Type -E. Glass Fiber Panel shall have a Class “A” flame spread rating of 25 or less. Mounting shall be over Griper/adhesive/ impaling clips/ fasteners, (i.e. nails, screws etc.) over ply batten fixed through screws on GI framework infilled with 50mm thick Acowool. Standard continuous wall leveling angle are to be provided by client and approved by consultant. Size of the panel 600x1200mm, 600x600mm or as per design Preferable Make : Envirotech; Sun India , Tarel

Acoustic Ceiling Panels

AUDIO SYSTEM Solution

MAIN FOH 2 Way Active Speaker. SPECIFICATIONS Max SPL *calculated 127 dBSPL Sensitivity *5-band average 99 dBSPL Frequency Response 60Hz – 20kHz Amplifier Power RMS: 380W Peak: 470W Transducers HF: 34mm Compression Driver LF: 15” High Power Woofer Directivity *H x V 85° x 75° Connections XLR+¼” In, XLR Out Dimensions *H x W x D 705 x 462 x 440mm Net Weight 21.5kg Shipping Weight 26kg Preferred Brand – QUEST / NEXO / AUDIOFOCUS

RUNNING Side 2 Way Ultra –Compact passive Speaker Horizontal Symmetry – Yes; Vertical Symmetry - Yes Operating Temperature (Maximum): 55 ; Operating Temperature (Minimum): -10 C Speaker Diametre (Driver): 203.20 mm; Maximum Frequency Response (Bandwidth): 20 kHz Maximum Frequency Response (Bandwidth): 20000 Hz; Minimum Frequency Response (Bandwidth): 80 Hz Minimum Frequency Response (Bandwidth): 0.08 kHz; Construction: Epoxy painted ply casing Coverage Horizontal: 90 degrees; Coverage Vertical: 60 degrees; Impedance: 8 ohm Maximum SPL (Sound Pressure Level): 120 dB; Power Handling: 200 Watt Vertical Symmetry: Yes; Depth: 240 mm; Height: 265 mm; Width: 420 mm Product Weight: 10 kg Preferred Brand – QUEST / NEXO / AUDIOFOCUS

POWERED Sub-Woofer, 1000 Watt This is suitable for mid to high sound pressure level bass and sub bass as a stand-alone unit. Powered (Active) - Yes Speaker Diametre (Driver): 381 mm Maximum Frequency Response (Bandwidth): 200 Hz Maximum Frequency Response (Bandwidth): 0.20 kHz Minimum Frequency Response (Bandwidth): 80 Hz Minimum Frequency Response (Bandwidth): 0.08 kHz Certifications: CE Impedance: 8 ohm Maximum SPL (Sound Pressure Level): 127 dB Power Handling: 650 Watt Depth: 635 mm Height: 535 mm Width: 450 mm Product Weight: 49.50 kg Warranty (Length/Type): 2 Years Limited Preferred Brand – QUEST / NEXO / AUDIOFOCUS

Stereo Digital Amplifier 4 x 1500 Watt per channel, 2RU (for all passive speakers) Specifications Frequency Response 20-20kHz (+/-0.3dB) Peak Output Current 40A Dynamic Range 111dB (A-weighted) Noise Level -67dBu (A-weighted) Distortion (1kHz@1W/8Ohm) 0.004% Distortion (1kHz@50W/8Ohm) 0.003% Crosstalk (1kHz@1W/8Ohm) -90dB Gain 32dB Maximum Input Level +24dBu Input Type XLR Balanced Inputs and Euroblock Links (+ optional Expansion Module) Input Sensitivity +4dBu Input Impedance 10kOhm Output Resistance 13mOhm Front Controls Volume Adjust, 80Hz HPF Enable, 100Hz LPF Enable, Limiter Enable, Auto standby enable, Features Wake On Music, Auto-Mute (1ms wake-up), Limiting on High Temperature Amplifier Protection Systems Thermal protection, Over-Current Protection, DC Protection, HF Protection Mains Input Voltage Range 85VAC - 265VAC Standby Power Consumption 4.9W Muted Power Consumption 25W Idle Power Consumption 50W Standard Power Consumption (Pink Noise@ 1/8th Rated Power, 8Ohm) 500W Preferred Brand – QUEST / NEXO / AUDIOFOCUS

16 mono channels; 16 internal time-delay effects; Neutrik mic XLR Neutrik 1/4 inch jacks; Channel insert; Super wide gain ‘DuoPre’ mic line input 3 band EQ with MusiQ; 2 pre-fade Aux sends; 1 post-fade Aux send 1 internal FX send; Illuminated mute; Sound image pan Illuminated PFL & peak warning indicator; ALPS 100mm faders 4 stereo channels with 2-band EQ and inputs for extra sources Stereo returns & playback; All inputs with level control 12 bar meters; Mono/stereo function on auxes 1&2 Monitor output section; Alt stereo output source Configurable USB stereo audio in/out Preferred Brand - ALEN & HEATH/ YAMAHA/ Behringer

Supply of Cordless mic , Hand Held dual channel with an Operating range 100 Mtr, 12 comptable system per frequency band ,OR BETTER. Preferred Brand - SHURE / SENNHEISER / Beyerdynamic

Supply of Chorded microphone with freq range-40Hz to 15 KHz, SPL 93 db ,output inpredance;150 OHMS OR BETTER. Preferred Brand - SHURE / SENNHEISER / Beyerdynamic

Supply of Instrumental microphone with freq range :40Hz to 15 KHz ,Polar pattern Cardioid, output inpendance:150 OHMS OR BETTER. Preferred Brand - SHURE / SENNHEISER / Beyerdynamic

SITC of connection cable, interconnecting cables, jacks etc and Interconnecting cables, speaker cables, PVC Conduit, Power Sockets etc., suitable cabinet for storing and operating the full system

VIDEO SYSTEM FOR AUDITORIUM SOLUTION

WUXGA Blue Core Laser Projector, 5000 Lumens Brightness, WXGA Resolutions, Native Aspect Ratio 16:10 Contrast Ratio (FOFO) 3000000:1 Display Color 30 Bits (1,07 billion colors) Light Source Laser, Light Source Life 20000 hrs, Brightness (ANSI lumens) 5000, Throw Ratio 1.36 ~ 2.18 Zoom Ratio 1.6x Lens F/# = 1.81 ~ 2.1,f = 14.3 ~ 22.9 mm Projection Offset (Full-Height) 0% Keystone Adjustment 2D, Vertical ± 30 degrees; Horizontal ± 30 degrees Lens Shift Vertical ± 60% Lens Shift Horizontal ± 23% Preferred Brand – BenQ, Barco, Christie

Heavy Duty Ceiling Mounting Bracket, 4 to 6 ft Drop adjustable with Necessary cables for projectors (Mains, HDMI).

Branded Motorised Projection Screen, size 12 ft x 9 ft, working on 230v AC, Operation by RF RC Unit and manual switch system, Wall type.

Cables, Infrastructures, Labour, Commissioning and installation charges

VIDEO SYSTEM

86”HD LED Interactive Digital Board with 450cd2 brightness with inbuilt speaker, with inbuilt Android 8.0 with 4GB RAM /32 GB ROM, in built 13 MP Camera and six array microphone. Preferred Brands – BARCO, HYUNDAI, HITACHI, LG, Christie. Specifications: Display System Display size, Surface & Technology. • Hardened surface with Anti Scratch & Anti Glare Surface • LED with min, 60 Hz refresh rate • Resolution : 3840x2160 (Min.) (for Landscape) • Aspect Ratio: 16:9 • Viewing Angle Range (Min.) : 176° (Horizontal) to 176° (vertical) • 450 cd/m2 • Contrast Ratio : 10000:1 • active display area – 1895.04(H) x 1065.96 (V) ii. Operating System • Power Supply : 240 V : 50 Hz • Operating temp : 0o C to 50o C • Operating Humidity : 10% to 80% • Wall Mountable iii. Audio • Inbuilt speakers (15 W x 2 – minimumfor each speaker) – Total 30 watt. iv. Remote • Remote Controller (Full functional; remote with batteries) ii. Operating System • Power Supply : 240 V : 50 Hz • Operating temp : 0o C to 50o C • Operating Humidity : 10% to 80% • Wall Mountable iii. Audio • Inbuilt speakers (15 W x 2 – minimumfor each speaker) – Total 30 watt. iv. Remote • Remote Controller (Full functional; remote with batteries) Input/output (I/O) System i.HDMI(ver 2.0)- Min. 2parts ii. HDMI(ver 2.0)- Min. 2parts iii. RJ 45 – Min 1 port (with 5m Patch Cable) iv. Wifi (802.11 b/g/n/ac) with Hotspot feature v. VGA /RGB/HDMI output (with cable toconnect external monitor/ device) vi. USB (2.0) – Min. 2Ports = USB (3.0) – Min.1 Port Touch System: i. Type : Infra Red Based ii. Inputs for Touch : Finger, Gloved Fingers, Opaque Objects/ Touch Pens iii. No. Of touch pens (with suitable tray/pen holder) :qty 2 iv. Touch scan rate : 50 scans/ sec (min) v. Touch Points : Multi touch ( min 10 touch points) vi. Response Time :< 15 msec vii. Touch accuracy : + 2 mm (Over 90% Area) i. Hardware : • (Min) Quad Processor based SoC (processor > 1.7 Ghz) ii. Operating System • Android/Linux/Open Source based O.S. iii. Software Apps (Pre Loaded) • Content Management Systems & Apps to support writing, Drawing Eraser, Screen Capture, Video Player, Recording, File & Folder Manager, Storage Management, Printer, Email, etc. • web Browser • Screen Sharing (Mira Cast)/(Google Cast) • Factory Resetting • Security features – Pin based and / or Password based. • Over the Air update of Apps & O.S.

SITC of Digital Podium with in built Audio and Digital system Smart Rostrum has PC with i3 processor, 4GB RAM, 500 HDD, DOS and Keyboard/Mouse, and can be customized to as per the requirement. Smart Podium has sliding top tray to place Laptop which allows presenter to display any multimedia file instantly. It is fully compatible with all types of Projectors. It has switching plate with buttons on the top, which allows you to display desired projection output, We integrate high quality, echo-free and branded audio equipment in Smart podiums, All cables and connectors inside the podium are tagged and well managed to simplify the structure complexity. 18” gooseneck microphone from premium brands integrated with the Smart Podium. It has 2 XLR ports on the top. All the doors, drawers, trays and shelves are lockable to avoid unauthorised access. It has in-built anti-theft mechanism. Switcher helps to switch the projection among different devices, while splitter helps to split the display for multiple outputs. Smart podium should have all the required input/output ports such as USB, VGA in/out, HDMI in/out, LAN, Audio in/out, XLR, Power and so on. Podium allows you to connect smart board with the projector directly, and helps you to conduct interactive lectures. It integrates full HD Document Camera which helps to project live document/object for audience with greater clarity, Podium has 4 caster wheels which enable it to move easily and effortlessly. Controller helps to operate all the electric & electronic devices using its touch screen etc. Preferred Brand – VAC / INGRESS / ITC / LIBERTY

SITC of Wall Mounted Weather Proof Speakers Max SPL *calculated 112 dB Sensitivity *5-band average 93 dB Frequency Response 75Hz – 20kHz±2dB Impedance 16Ω Transformer Taping 100V 20w/30w/40w/60w 70V 10w/15w/20w/30w Amplifier Power RMS 100W Peak 200W Transducers HF 25mm Titanium Dome Tweeter LF 8” High Performance Polypropylene Woofer Directivity *H x V 150° x 120° -10dB Connections Captive Screw Terminal Plug (In/Thru) Environmental Ingress Rating Speaker Cabinet IP56 (IP67 when used with IPMX1 kit) Dimensions *H x W x D 345 x 202 x 243mm Net Weight 4.3 kg Shipping Weight 6.0 kg Preferred Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

SITC of Wall Mounted FOH Speakers Horizontal Symmetry – Yes; Vertical Symmetry – Yes; Operating Temperature (Maximum): 55 C Operating Temperature (Minimum): -10 C; Speaker Diametre (Driver): 203.20 mm Maximum Frequency Response (Bandwidth): 20 kHz Maximum Frequency Response (Bandwidth): 20000 Hz Minimum Frequency Response (Bandwidth): 80 Hz Minimum Frequency Response (Bandwidth): 0.08 kHz Construction: Epoxy painted ply casing; Coverage Horizontal: 90 degrees Coverage Vertical: 60 degrees; Horizontal Symmetry: Yes Impedance: 8 ohm; Maximum SPL (Sound Pressure Level): 120 dB Power Handling: 200 Watt; Preferred Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

SITC of 6 channel Analog Audio Mixer, with in built MP3 Player, Echo effect etc. Preferred Brand – ALLEN & HEATH / STRANGER / STUDIOMASTER

SITC of connection cable, interconnecting cables, jacks etc and Interconnecting cables, speaker cables, PVC Conduit, Power Sockets etc., suitable cabinet for storing and operating the full system

INGRESS FLOOR KIOSK

Floor standing digital signage kiosk with HD display, 3840 x 2160 (4K) resolution Android 9.0 or higher with 4GB RAM and 32GB ROM, Wifi Enabled , HDMII , USB , Strong MS enclosure with power coated finish , AL frame , front 7mm toughened glass, anti vandal desgin , service door with lock , preloaded signage software (Windows optional) Size-55”,Brightness-400cd2,Speaker- 10w x 2

A) DIGITAL WIRED AUDIO CONFERENCE SYSTEM, DIGITAL BOARD AND V.C SYSTEM ETC FOR CONFERENCE ROOM

SITC of Digital Chairman Discussion /Conference Unit with Removable Microphone of minimum Length 400mm Chairman Discussion Unit with built-in Digital Signal Processing Unit with Priority and Next-in-Line Configuration Priority button silences all delegate microphones and allows only the chairperson to speak; Next-in-line button gives the floor to the next speaker in a waiting list of speakers who requested to speak. User Button with Feedback; Shielded microphone, immune to mobile phone interference, High-quality integrated loudspeaker; Headphone output with Volume Adjustment Loop-through, daisy-chain cabling; Unit with Bi color bar indicator Compatible Screw Lock Microphone of length 400mm Different LED Signalling for Mic On/Off OR Request-to-Speak Push Button or better Audio Quality 16Bit digital; Frequency response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Microphone with Ring Indicator to light up Red when active and Green when in Request Connection: Screw Lock Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

SITC of Digital Delegate Discussion / Conference Unit with Removable Microphone of minimum Length 400mm Delegate Discussion Unit with built-in Digital Signal Processing Unit with Microphone On / Off Button; User Button with Feedback Shielded microphone, immune to mobile phone interference High-quality integrated loudspeaker; Headphone connection. Audio Quality 16Bit digital; Frequency Response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Connection: Screw Lock Microphone with Ring Indicator to light up Red when active and Green when in Request Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

SITC of Conference connection cable, 10m, black and other interconnecting cables, jacks etc should be from Reputed Makes.

SITC of Digital Audio Processor for Configuring VC system with Conference system 6 Channel Digital Processor Inputs : 4 balanced mic, 2 balanced Mic/Line,1 stereo unbalanced input Inputs equipped with Low-cut filter, phase inversion and 4-band EQ Onboard AEC processing; 1 stereo and 2 mono outputs Each output channel equipped with adjustable output level, 12-band fully parametric EQ with notch filtering, compressor, limiter, and 8-band feedback suppressor. 2-channel USB audio interface 8 x 3 audio routing matrix; Maximum Gain : 64 dB or better Dynamic Range : 110 dB or better; Signal-to-noise ratio:90 dB or better Front panel Monitoring, Controls and LED indicators; Web Remote functionality IP control for third-party CCS administration; Cascadable upto 6 units Euroblock connectors Accessories : Rack-mount adapters Approved make : Biamp / Clearone / QSC / Audio Technica

Digital Interactive Flat Panel (Digital Board) for Conference Room of Lower Ground Floor Plan

SITC of 86”HD LED Interactive Digital Board with 450 cd2 brightness, 8GB RAM, 64GB Internal Model S86UKAI Preferred Brand – BARCO / HYUNDAI / HITACHI / LG / CRISTIE Specifications: Display System Display size, Surface & Technology. • Hardened surface with Anti Scratch & Anti Glare Surface • LED with min, 60 Hz refresh rate • Resolution : 3840x2160 (Min.) (for Landscape) • Aspect Ratio: 16:9 • Viewing Angle Range (Min.) : 176° (Horizontal) to 176° (vertical) • 450 cd/m2 • Contrast Ratio : 10000:1 • active display area – 1895.04(H) x 1065.96 (V) ii. Operating System • Power Supply : 240 V : 50 Hz • Operating temp : 0o C to 50o C • Operating Humidity : 10% to 80% • Wall Mountable iii. Audio • Inbuilt speakers (15 W x 2 – minimumfor each speaker) – Total 30 watt. iv. Remote • Remote Controller (Full functional; remote with batteries) Input/output (I/O) System i.HDMI(ver 2.0)- Min. 2parts ii. HDMI(ver 2.0)- Min. 2parts iii. RJ 45 – Min 1 port (with 5m Patch Cable) iv. Wifi (802.11 b/g/n/ac) with Hotspot feature v. VGA /RGB/HDMI output (with cable toconnect external monitor/ device) vi. USB (2.0) – Min. 2Ports = USB (3.0) – Min.1 Port Touch System: i. Type : Infra Red Based ii. Inputs for Touch : Finger, Gloved Fingers, Opaque Objects/ Touch Pens iii. No. Of touch pens (with suitable tray/pen holder) :qty 2 iv. Touch scan rate : 50 scans/ sec (min) v. Touch Points : Multi touch ( min 10 touch points) vi. Response Time :< 15 msec vii. Touch accuracy : + 2 mm (Over 90% Area) i. Hardware : • (Min) Quad Processor based SoC (processor > 2.2 Ghz) ii. Operating System • Android/Linux/Open Source based O.S. iii. Software Apps (Pre Loaded) • Content Management Systems & Apps to support writing, Drawing Eraser, Screen Capture, Video Player, Recording, File & Folder Manager, Storage Management, Printer, Email, etc. • web Browser • Screen Sharing (Mira Cast)/(Google Cast) • Factory Resetting • Security features – Pin based and / or Password based. • Over the Air update of Apps & O.S

MULTI PARTY V.C SYSTEM WITH PTZ CAMERA

Lumens / Siemens / Barco / Polycom PTZ Camera Supply of FHD PTZ Camera Equipped with a 1/2.8 inch image sensor USB 3.0 and HDMI video output interface USB 3.0 Plug & Play and compatible with Windows, Linux, MAC OSX, Chrome OS Full HD 1080p signal output format with a high frame rate of 60 fps 12 x Optical zoom is applicable for a medium size conference room Horizontal viewing angle: 72° Wide range Pan/Tilt/Zoom actions: Pan angle from -100° to + 100°; tilting angle from -30° to +30° Up to 125 user-defined preset modes to allow for ease of use in all environments. Bidder must attach FCC, CE, ROHS and BIS Certificate for the quoted Model BIAMP / EXTRON / BXB DSP Supply of 4 X 4 Digital Audio Matrix Processor with Supports adaptive echo cancellation 60 dB/S convergence rate 80 dB echo cancellation level. Supports adaptive feedback control. Built in automatic noise suppression making the SNR increase 18 db. Supports AGC auto gain contro l 6 dB~+ 18 dB auto balance control 12 dB~+ 12 dB. Supports gainsharing automatic mixer. Equipped with matrix function to self define the output audio sources. Centralized control via RS 232 RS 485 and UDP easily connect the third party equipment such as PTZ cameras. Sampling rate/ digitizing bit : 48K/24bit. Input gain : 0/10/20/30/40/43dBu. Output level: 6dB. Phantom power : 48V, Frequency Response : 20~20KHz 0.2dB, Max. level : +24dBu, THD + Noise : 0.003% @4dBu, Dynamic range : 113dB, Background noise (Aweighted): -90dBu, Common mode rejection ratio @60Hz : 80dB, Channel isolation @1KHz : 108dB, Input impedance : 5.4KΩ, Output impedance : 102Ω, System Delay: <3ms. Ethernet connector for PC software and TCP IP API control. Accessories 10m USB cable for Camera to Laptop. 5m USB for DSP to Laptop HP / LENOVO / APPLE NOTEBOOK SPECIFICATION: Intel®️ Core™️ i5- 1135G7 Processor ®️ - 11th Generation (8M Cache, Turbo Up to 4.20 GHz) / 8 GB DDR4 RAM / Intel Iris Xe Graphics / 512 GB PCIe®️ NVMe™️ M.2 SSD/ NO DVD-RW / Wi-Fi / Bluetooth / HDR Web Cam / In-built Alexa /15.6" Full HD IPS Micro Edge Anti Glare Display / 1 Super Speed USB Type-C, 2 Super Speed USB Type-A / HDMI / Ergonomic Keyboard / Preloaded Win 10 Basic SL + Home and Student 2019 / Weight – 1.7 Kg / Carry case/ Color- Silver, 15.6 Monitor size

FAÇADE LIGHTING

Supply, installation, testing & commissioning of Neon Strip 3000K (Mono) 12-15W/Meter With Driver & Accessories (Illumination of Façade Front Entrance Wings Portions Vertical Lighting) Make or Code: Havells Neon Strip

Supply, installation, testing & commissioning of Illumination of Side Building vertical Columns Lineate INT 80W DMX 25° LHEUAAPSNN7J080

Supply, installation, testing & commissioning of Illumination of Side Building vertical Column M15 Female Supply Cable 1M 3 Pin LSSLOB0078

Supply, installation, testing & commissioning of Illumination of Side Building vertical Column M15 EXTENSION CABLE 1M 3 PIN LSSLOB0079

Supply, installation, testing & commissioning of Illumination of Side Building vertical Column M15 EXTENSION CABLE 3M 3 PIN LSSLOB0174

Supply, installation, testing & commissioning of Illumination of Side Building vertical Column CS JUNCTION BOX 3 WAY LSSLOG0174

Supply, installation, testing & commissioning of DMX Controller (UE11 ) LSSLOG0178 DMX + ACCESSORIES (1 set )

Supply, installation, testing & commissioning of Address writer LSSLOG0051 DMX + ACCESSORIES (1 set )

Supply, installation, testing & commissioning of Instruction Forwarder Ranger/Compass(AC) LSSLOB0056 DMX + ACCESSORIES (1 set )

Supply, installation, testing & commissioning of DMX SPLITTER (INK) LSSLOB0263 DMX + ACCESSORIES (1 set )

Supply and Installation of 15/16w LED DALI Based RECESSED ROUND DIMMABLE LED DOWNLIGHTER similar to Havells Cat Ref : Integra Neo Smart + Driver

Supply and Installation of Recessed/ Surface 36W Linear LED Light made of Extruded Aluminium housing Similar to Havells Destello or Equivalent

ART WORK

Hand painting directly on wall Concept Creation Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. ARWORK EXECUTION Towards the cost doing hand painting using artist quality colors by qualified artists and protected by pu coating (mrf/akzonobel) all under the watchful eyes of expert artist

Mixed media mural Wood/metal/fiberglass/terracotta /tiles or anything other medium artist find suitable as long as it is permanent in nature. Concept Creation Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for

approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions ,Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork execution Towards the cost of making 3D relief mural in approved medium(Wood/metal/fiberglass/terracotta /tiles or anything other medium artist find suitable as long as it is permanent in nature.) and protective pu coating(akzo nobel/sirca) all under the watchful eyes of expert artist.

SIGNAGE WORK

Laser Cut 5 mm Acrylic Signage with Plotter Cut Vinyl letters pasted above & Desired color vinyl pasted on Back. 4 Inch X 12 Inch

Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as required.4 Feet by 2 Feet with backdrop high quality artwork print as per direction of Architect/EIC.

Backlit Acrylic Box Lit with Korean Led .4 Inch X 8 Inch

Laser Cut 5 mm Acrylic Letters with Pasted over 5 mm Acrylic Sheet with 6 studs.2 Feet by 4 Feet

Providing and fixing of Stainless Steel Box up Letters with White LED building signage, size 3 Feet x 30 Feet in SS (304 grade) back side proper lighting all complete with all accessories as per direction of EIC.

FURNITURE WORK

CASH COUNTER :-W1200xD475xH1185mm

Providing and fixing of Reception Desk having Dimension 1185mm Height . It has 25mm thick Worktop and Gable Ends made of pre Laminated Particle Board sealed with PVC Edge Banding. Front and Modesty Panel are 18mm thick Pre Laminated ParticleBoard Sealed with PVC EdgeBanding.. The Counter Top is 25 mm Thick Postformed ParticleBoard. Unit has One Pull out drawer with Lock and Handle. Certifications - ISO 9001 - 2015 ,14001- 2015 ,45001-2018 , BIS and BIFMA Complaint member , BIFMA GOLD . Warranty 5 years .

TABLE :-W1500xD600xH750MM

Providing and fixing of Worksurfaces Standard worksurface tops are nominal 25mm Thick Pre laminated Particle Board with 2 mm Matching PVC Edge Banding all around. Flipping/Nesting Table Frame The framework for table support and flipping/nesting operation consists of 1 1/2" diameter, .06" thick wall, steel tubing with 1/2" threaded inserts welded inside the tubes for mounting the legs. 4mm thick stamped steel brackets support the horizontal framework through injection molded Acetal bushings while 1/4" Phillips wood screws attach the framework brackets to the worksurface. The 3/4" diameter steel latch release handle is actuated at the center and front underside of the worksurface. Pulling forward, using one hand, raises the worksurface for nesting storage. To lower the table for use from the upright storage position, a steel locking latch is located on one support arm and must be released prior to lowering the table. All hinge pins for the flipping mechanism are zinc plated steel. Hinge pin spaces are molded nylon. The framework is shipped separately, ready to be assembled to the worksurface and legs. Leg Assembly The leg assembly consists of one right-hand leg and one left-hand leg. There are two leg widths. One width fits 20" & 24" wide tables. One width fits 30" and 36" wide tables. Leg height is fixed to provide only 29" high table-top height. ADA table height of 32" is accomplished using 3" leg extensions threaded into the bottom of the leg. Leg construction consists of 1 1/4" diameter, .078" thick wall, bent steel tubing welded in an assembly. The legs are bolted to the table support mechanism using 1/2" hex bolts. Leg assemblies ship knocked down. Casters and Glides Each table has four casters, 3" diameter, twin wheel swiveling casters are provided as standard. Two casters are locking, two are freewheeling. All are black nylon wheels with white hubs. Caster wheel treads shall be medium hard for easy mobility on carpet or hard floors. Steel 1/2" threaded stems attach the wheels to the bottom of leg assemblies. 2 3/4" diameter black nylon glides are optional. Glides have 1" of telescoping height adjustment that adjusts table height from 28 1/2" to 29 1/2". Steel 1/2" threaded stems attach the glides to legs. Casters and glides ship unassembled. Ganging Mechanism Built of black, high-strength nylon, the hook and peg combination draws tables together. No tools are required when joining tables. Gangers are self-storing under the table when not in use. Tops are pre-drilled for placement of ganging pegs. Two gangers, four pegs and all mounting screws are included in the kit. One kit per table joint is required. Field installed.

CHAIR

FLUENCE HB - Leatherette Back Height - High Back with headrest Back Finish - Leatherette with lumbar support Back Frame - Black Seat Finish - Leatherette Seat Height Adjustment - Pneumatic Mechanism - Weight Activated mechanism with seat depth adjustment Armrests Type - 3D Adjustable Armpads Type - Polyurethane Base Type - 5-Star in Nylon Base Warranty - 10 years from the date of invoice

1 SEATER SOFA- Providing & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by EIC

2 SEATER SOFA-Providing & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by EIC

3 SEATER SOFA-Providing & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by EIC

RESTAURANT/CAFETERIA

Providing & Fixing of Cafe table . The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed.Understructure is SS base of Dia 580mm.The above furniture should be as per specification and sample approved by client.CAFÉ TABLE :-D900xH750MM

CHAIR

Seat is made of Injection molded polypropylene. Seat is attached to the frame by the back attachment and with two steel Pal-nuts . Backrest is also made of Injection molded polypropylene. Attached to the frame with two metal clips. Contains a contoured handle opening at the top for easy lifting and stacking.Chair Frame Construction - Welded construction made primarily of 7/16" diameter steel wire (solid) bent to shape on a CNC wire bender. A 7-gauge steel seat strap, ribbed for added strength, supports the front of the seat and a 7/16" contoured steel rod joins the front legs for strength. Frame Finish - Bright chrome plated finish with duplex (semi-bright) nickel, bright nickel and chrome applied. Nickel provides corrosion resistance. Warranty 5 years .

Auditorium Chair-TSI - Trolium series

Supply & Installation of Auditorium Chairs Having General : Fabricate Auditorium seating with Auto Tip Up, Synchronized Push back, Foldable Writing Pad with Provision for Power and Data connectors to each Chair with PU padding with 3 Layer 100% Yarn Dyed fabric Upholsteries with injection-moulded seat and back Plastic covers. Equip each seat with a self-rising Torsion Spring compensating mechanism so that unoccupied seats return to an upright position perpendicular to the base line of floor of auditorium. Chair profile with the seat in the upright position and without a tablet arm, The Seat Size should be 45 cm x 45 cm & the Back size should be 45 cm x 66 cm with ergonomically designed seat and back cushions. Chair should be available in 22” and 23” to use multiple seat size in one layout for matching variable arch length. Seat Construction: Seat construction PU padding with Structural Powder Coated ERW Tube frame made by 22.23 mm Diameter tube with 1.6 mm thickness as per IS :3074-2005 grade1, fabric Upholsteries with injection-moulded seat and back Plastic covers. Equip each seat with a self-rising Torsion Spring compensating mechanism as per IS : 4454 1981 grade 3 (part i) tested for 5,00,000 cycles. so that unoccupied seats return to an upright position perpendicular to the base line of floor of auditorium PU padding with 3 Layer 100% Yarn Dyed fabric Upholsteries with injection-moulded seat and back Plastic covers. The outer seat cover shall have a good exterior surface and internal moulded reinforcing ribs for a solid warp-free construction. Seat Cushioning to be Made by 45 +/- 3 Kg Density Polyurethane Foam shall be applied over the 7 Tank Powder coated Metal frame. Foam shall be fire retardant and conform to the California Bureau of Home Furnishings Technical Bulletin 117 to secure maximum safety in event of fire. The upholstery cover shall be sewn and fitted to the seat assembly with collapsible assembly rings and nylon tension cord.. Back Construction: Back construction PU padding with Structural Powder Coated ERW Tube frame made by 22.23 mm Diameter tube with 1.2 mm thickness as per IS :3074-2005 grade1, fabric Upholsteries with injection-moulded seat and back Plastic covers. PU padding with 3 Layer 100% Yarn Dyed fabric Upholsteries with injection-moulded seat and back Plastic covers. The outer Back cover shall have a good exterior surface and internal moulded reinforcing ribs for a solid warp-free construction. Back Cushioning to be made by 45 +/- 5 Kg Density Polyurethane Foam shall be applied over the 7 Tank Powder coated Metal frame. Foam shall be fire retardant and conform to the California Bureau of Home Furnishings Technical Bulletin 117 to secure maximum safety in event of fire. The upholstery cover shall be sewn and fitted to the seat assembly with collapsible assembly rings and nylon tension cord.. Metal Stands : Frame shall be 8 cm x 4 cm x 1.6 mm cold-rolled welded steel tubing; formed steel brackets welded into ne integral freestanding structure upon which the seat, back, and arms are assembled with Provision for Power and Data connectors to each Chair, along with Sliding System Mounting Provision and Writing pad Concealing feature.. Floor mount plate shall be .100” thick hot-rolled pickled in- oil steel base plate by mounting anchors. The same Metal Structure provide Location for the hinge Point to self-rising mechanism of seat. The whole structure shall be finished with Black powder coating. The metal assembly consist of Synchronized Liner sliding system consist of a pair of self-lubricating Engineering Polymer Preferably Self-lubricating DuPont ZYTEL based metal Sliders with Polymer coating of 0.2 cm thickness to give the long life maintenance free performance to the push back system to seat assembly.All Exposed Metal part need to do high quality of Powder coating of Black Matt Finish to prevent lustre. Armrest: Shall be Made out of Solid Wood as per finish approved by Employer. Solid Wooden or PU armrest option should be available. Writing Pad System : Plastic or PLB Writing Pad should be provided in such a way that it gets Concealed when not in use. Writing pad Mechanism made by dual hinge point that allow user to park the writing pad under the armrest. Hinge should be Made up by aluminium Die cast junction block of 8-10 mm thickness duly powder coated. Writing pad Arm should be made up by ERW tube as per IS :3074-2005 grade1. Hinge : The Seat portion should have the proper hinge through a Axel of 1.4 cm dia Solid Metal Bar to have proper seat movement. Warranty: Warranty should be minimum of 36 months from the date of commissioning against manufacturing defects.

VISITOR CHAIR 3 SEATER FOR WAITING AREA

Supplying and placing of 3 seater visitor chair with 2 arms. The seat and back shall be made up of reinforced PU foam with MS perforated sheet. The seat mounted on MS powder coated rectangular cross beam having cross-section area 60mm X 60mm with 2mm thick fitted with polypropylene end caps on both side. The arm and leg shall be made up of pressure diecast aluminium. there shall be leveller shoe provided at the bottom with metal insert. The individual seat size shall be 515±10 mm(W) X 467±10 mm(D), Back size shall be 515±10 mm(W) X 510mm±10 mm(H) from seat, Overall depth shall be 680±10 mm, overall height shall be 860±10 mm and overall width shall be 1640 ±10 mm.The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, ISO 45001:2018 , BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA.

CONFERENCE TABLE (11500mm X 1200mm X 750mm)

Supplying and placing Of Conference Table,* SUPPLYING, AND PLACING IN POSITION CONFERENCE ROOM TABLE, OFFERS YOU A GENEROUS WORKSPACE,DESK PRIMARY WORK SURFACE USE PREMIUM QUALITY MATERIALS.TABLE TOP SHALL BE MADE OUT OF 25 MM THICK PRELAMINATED PARTICLE BOARD OF GRADE II TYPE III OF IS 12823/LATEST,CONSTRUCTION PROVISION THE OVAL SHAPED CONFERENCE TABLE OVER ALL SIZE IS 4500 MM (L) X 1800MM (D) X 750MM (H) MADE OUT OF 25 MM THICK PRELAMINATED PARTICLE BOARD AND TOP BASED ON SIDE PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400 MM(L) X 715 MM(H) AND BELOW THE TABLE TOP MODESTY PANEL SHALL BE MADE 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 1559 MM(L) X 400 MM(H). * CONFERENCE TABLE EXTANDABLE PART COMES IN SEMICIRCLE SHAPED SIZE IS 1200MM (L) X 600MM (D) X 750MM (H).EXTANDABLE PART TOP MADE OUT OF 25MM THICK IN PRELAMINATED PARTICLE BOARD.TOP BASED ON CENTER PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400 MM(L) X 715 MM(H) AND BELOW THE EXTANDABLE PART TOP MODESTY PANEL SHALL BE MADE 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 200 MM(L) X 400 MM(H) .WHEN THE EXTANDABLE PART AND TABLE FIXED TOGHETHER SUPPORTING WITH 18MM THICK PRELAMINATED PARTICLE BOARD BOX SIZE IS 209 MM(L) X 400 MM(H).OUR WORK SURFACE FURNITURE IS FINISHED WITH EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE,FIXED WITH HOT MELT GLUE.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKEDURIAN.WARRANTY-5YEARS

MAIN CHAIR FOR CONFERENCE

Providing and placing High back chair ergonomicaly designed for complete lumber support . Seat & back assembly which is made of wooden frame in combination of wood and 12mm thick commercial plywood .The seat and back are arrested together for motion on central pivot with Urethane foam with 40+/2 kg/m3 in seat and 32 kg/m3 in back and fabric/leatherite tapestry.The seat and back's sides covered with wooden moulding both side which is polished and armrests are made of rubber wood melamined and die casted aluminium . The Base made of metal insert made of CRCA metal pipe size 30mm x 15mm x 1.6mm and cover with rubber wood & PP 5 star at load tested 1100 kg ,with superior Nylon-6/Ultramid -56 twin wheel castors having self lubricating properties for friction free movement.The seat height adustment with bifma standard class 4 gas lift. The mechanism is torsion bar with single point locking and tension adjustment . Seat Size 20" X 20" and back Size 28" from seat & overall Ht 46". * THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

CONFERENCE CHAIR

MMPL/70020/LB : LOW BACK MESH CHAIR IN BLACK COLOUR WITH MATTE FINISH SPECIFICATION : DURIAN - - OFFICE SEATING - - MAGIC CHAIR , TYPE : * LOW BACK 360° DEGRE REVOLVING CHAIR SKU : 70020/LB, * ALL OVER SIZE IS : 625MM(L)X 450MM(D)X 920MM(H) , *THE CHAIR MADE OF FULL MESH IN BLACK COLOUR . IT WILL COMES IN MATTE FINSIH IN CONTEMPORARY STYLE . DETAILS : * ARMS : FIXED PP ARMREST . * USE OF PLY: 12 MM THICK HOT PRESSED BWR PLYWOOD (IS GRADE - 303 FOR SEAT). * SEAT: 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN SEAT , * BACK : FRAME OF DESIGN SHALL BE CURVED MADE OF TWO PIECES INJECTION MOULDED FRAME COVER WITH MESH .BACKREST SUPPORT MESH DESIGN BASED ON SYMMETRICAL LUMBAR SUPPORT * MECHANISM : SYNCRO SINGLE LOCKING MECHANISM . * ONLY SEAT SIZE IS 445MM(L)X 450MM(D)X 520-425MM(H) & THE BACK SIZE IS 625MM(L)X 480MM(H) , SEAT MAXIMUM HEIGHT IS 520MM & MINIMUM HEIGHT IS 425MM & BACK HEIGHT FROM FLOOR MAXIMUM HEIGHT IS 920MM & MINIMUM HEIGHT IS 820MM . * GAS LIFT 100 MM TELESCOPIC HAUDRAULIC * BASE : 650MM NYLON BASE WITH SMOOTH CASTORS . * THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

Providing & Fixing Home Defense and Law Enforcement and Security and Safety Equipment and Supplies Security surveillance and detection surveillance and detection equipment Door Frame Metal Detector.DIMENSIONS-2000X720X570 Weight Not more than 80 Kg

Providing & Fixing Home Defense and Law Enforcement and Security and Safety Equipment and Supplies Security surveillance and detection surveillance and detection equipmentX - Ray Baggage Inspection System As Per MHA QRs System Size Small Size Tunnel Width (W) 60 cm for Small S Tunnel Height (H) 40 cm for Small S Conveyor Capacity >= 160 kg for SmSize

SITC of 55 Inches touch vertical signage with windows PC (i5) & signage software

SITC of 18 feet high bronze statue of Bhagwan Birsa Munda.all complete as per approved design, specification and direction of E/l.

BUILDING MANAGEMENT SYSTEM

CENTRAL CONTROL STATION

SITC of BMS Computer System: i7 Processor or Equivalet Server PC, Intel(R) Xeon(R) Processor, 2.93GHz, 4MB Cache with 16 GB RAM, 256 GB SDD, 1 TB HDD, 2 GB Graphics Card, 10/100 Mbps Ethernet card, USB connection & internal modem, Web server software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and anti virus software as per Tender Specifications. Accessories included Wireless Optical Mouse & Key Pad, with the above BMS System configuration. MS Windows 10 Enterprise or latest Licensed software compatible with the BMS platform etc. complete as required. Makes (Dell/HP/Lenovo)

Laserjet A4 Color Printer

APPLICATION SOFTWARE

Supply, installation, testing and commissioning of the following window based graphical software for IBMS system with 1 No. Client for Operator workstation. The Software shall have 3D & HD vector dynamic graphics with Autocad import of plan with Zoom In & Zoom Out facility, Native 64 Bit System, Multi-Monitor Support-( Max 4 Nos), Multi-language support, BTL, UL, EN Certified System, BACnet Profile B-AWS (Advanced workstation) as per the BTL Listing, dot net platform, Certified OPC DA Server by OPC Foundation, Web-Based Server software shall permit use of Standard Web-Browsers such as Microsoft Internet Explorer, Netscape Navigator, etc. The Software shall comply to international standards and strive to deliver products that meet security standards such as ISA/IEC 62443, UL2900, ISO/IEC 27001, ISO/IEC62443 and OWASP. Cybersecurity audit trail, 4-eye principle, Seamless integration of certificates within customer IT infrastructure, Microsoft’s active directory-based authentication, Use of network infrastructure that supports physical network or VLAN segmentation, Placing the web server in a “demilitarized zone” (DMZ), End-to-end encryption, from client to server, End-to-end encryption between servers, Certificate-based data exchange, Encrypted backups. Special Note - The Software should have cloud connectivty and can be access remotively using User Name and Password from anywhere. For further compliance vendor to follow the Tender specifications

INTEGRATORS

Supply, installation, testing and commissioning of True IP Based BTL & UL Listed for third party integration. The controller shall have 2-port Ethernet switch, WLAN interface and Cloud Connectivity. It should have BTL label (BACnet communications passed the BTL test) and consisting of Dual microprocessor with Storage capacity of 1 GByte RAM. It should support Real Time clock upto 7 Days. It should Support of the major communication protocols: BACnet/IP, BACnet MS/TP, Modbus IP and Modbus RTU upto 500 points. (Note - Integrator shall be of same DDC make only.)

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required. Number of controllers shall have spare capacity of 10% for future expansion.

For Fire ALARM System on Bacnet/IP - 1500 Points

For DG Sets on Modbus RS485 - 30 Points

For Multifunctional energy meters Modbus/RS485 - 200 Points

For Lifts on Bacnet/IP

For STP Plant Integration - 100 Points

For UPS Sets on Modbus RS485 - 30 Points

For EV Charging on Modbus

For CCTV and Access Control System Critical Parameters monitoring on OPC

For Boom Barrier on Modbus

DDC CONTROLLERS

Supply, installation, testing and commissioning of True IP Based DDC Standalone 32 Bit Intelligent, inbuilt web browser, peer to peer communication, interoperable DDC as per the specification. The controller shall have inbuilt 2-port Ethernet switch. The DDC shall have 300 Mhz processor with 128 MByte SDRAM (DDR3) and 512 MByte NAND Flash. The DDC shall have IT security including HTTPS and BACnet Secure Connect communication, Operating voltage AC 24 V. The controller shall be freely programmable and have System functions (alarming, scheduling, trending, access protection with individually definable user profiles and categories). Each DDC shall have WLAN interface for local operation, engineering and commissioning. It should have one integration port inbuilt and port for POT for local interface. For further compliance vendor to follow the Tender specifications .

Controller for Electrical System (DG Sets/LT/GT/Lift)

Controller for Plumbing System

FIELD INSTRUMENTS

Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters. The DDC shall support sensor with DC 0...20 mA or 4...20 mA, DC 0 ... 10 V, LGNi 1000, 2x LG- Ni1000, Pt 1000 , NTC 10k, NTC 100k, 1000 Ohm.

Flameproof Level Switch

Voltage Transducer

Current Relay

Water pressure sensor

Bi Level Switch

Cable, Conduit and Cable Tray

Supply, Installation, Testing & Commissioning of the following cables, conduit and cable tray as per the specifications:

2 Core 1 Sqmm Annealed Tinned Copper, Twisted pair , Shielded Un-armoured cable for signal and power as per specifications

4 Core 1 Sqmm Annealed Tinned Copper, Twisted pair , Shielded Un-armoured cable for signal and power as per specifications

Cat-6 unarmoured cable with required jacks and points

25 mm MS Conduit including all accessories

HOT DIP GALVANISED GALVANISED PERFORATED TYPE CABLE TRAY

GI Flexible 25 mm

NETWORK SWITCHES

Supply, installation, testing and commissioning of Layer 2 unmanaged switch with 16/24 ports (RJ-45) port rack mountable, SMPS power supply. The switch to switch distance shall not exceed beyond 80 meters

Operation and Maintenance of services of the below listed item will be operated for 1 years after completion of defect liability period.

LIFT/LV SYSTEM Operation of all Lift units, L V System during ONE years of DLP. Operator shall be available at Campus 24X7. The rates shall be inclusive of all spare, accessories, consumbles, manpower, tools and tackles , replacement of parts,(except fuel , power and water) including routine servicing and maintenance of equipment (Equipment list can be refer as per BOQ) etc complete in all respect as per direction of Engineer in charge.For 1st year

Civil Works Operation of civil and plumbing work such as development of hair cracks, misc repair, leackage of pipe etc comprising of all the tools,repair material, etc as required with scaffolding complete inall respect as per satisfaction of E/I. For 1st year

Electrical Work Operation of all Panel (HT/LT), DB,DG Transformer,etc after one years of DLP Operator shall be avilable at campus 24*7 .The rate shall be inclusive of all spare accessories ,consumbles,manpower,tools and tackles, replacement of parts (except fuel ,power and water) includinng routine servicing and maintance of equipment ( Equipment list can be refer as per BOQ) etc complete in all respectas per direction of Engineer in Charge .For 1st year

HVAC Work Operation & maintenance ( routine & and preventive) and breakdown maintenance of high side & low side the Air conditioning plant comprising of all the machinery (Equipment list can be refer as per BOQ) installed in the A.C. Plant room including cooling tower as per maintence schedule attached at Annexure H of CPWD Specification .For 1st year

STP,WTP Operation & Maintence STP,WTP, ETP units after defect liability period,Operator shall be available at plant 24 X7 The rate shall be inclusive of all spare accessories, consumables, manpower,tools, and tackles, replacement of parts, { except fuel, power and water) including routine servicing and maintenance of equipment (Equipment list can be refer as per BOQ) etc complete in all respects as per direction of Engineer in charge.For 1st year

HORTICULTURE WORKS

SUPPLYING WORKS

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

PREPARATION WORKS

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

PLANTING WORKS

In rows 5 cm apart in both directions

MAINTENANCE WORKS

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 60 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid for separately)

TREES

Azadiractha indica

Bahunia purpurea

Butea monosperma

Cassia fistula

Delbergia sisoo

Delonix regia

Grevillea robusta

Jacranda mimosifolia

Plumeria alba

SHRUBS

Aclypha wilkensiana

Bouganvillia mahara

GROUND COVERS

Alpinia zerumbet

Alternanthera

Supply & Installation of Musical Fountain of attached specfication all complete as per direction of E/I

Labour Cess @1%

M/S PRASAD CONSTRUCTION & CO