Construction of MTC Bus Stand at Avadi, Chennai

Amount

Removing the existing ventilators,doors and windows including removal of frames, hinges and fastenings carefully and stacking the same at site etc., complete

Dismantling the existing brick or stone masonry work in cement mortar under 3m high including carefully clearing the debris etc.,complete.

Dismantling RCC by manual / by using deploying machineries carefully clearing away the debris as directed during execution. The dismantling of concrete as per PWD schedule of rates are to be adopted wherein a part part of the concrete only is to be dismantled and the remaining part of the concrete has to be retained structurally safe.

Dismantling, Plain cement concrete and clearing away the same 50 m away from the site and roughening the surface etc., complete complying with standard specification and as directed by the Departmental officers.

Dismantling, clearing away and carefully stacking materials :Corrugated Iron Sheet Roofing over Pan Tiles without roof timber, Structural steel works

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete SS.20B

Narrow Foundations for building & culvert- First Depth Upto 2m

Narrow Foundations - Second Depth 2m - 3m

Narrow Foundations - Third Depth 3m - 4m

Providing and constructing cast in situ hydraulic bored piles of 375mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc ., Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Providing and constructing cast in situ hydraulic bored piles of 600 mm diameter in M35 grade concrete using blended cement - slag cement with minimum cement content of 440kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, permanent casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Initial pile Load test (excluding pile cost) (Design load)

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and laying of Sand Gravel Mix in ratio 1:1 for using 0.631 m3 of sand fo filling and 0.675 M3 of red gravel of 1m3 of volume including cost of sand gravel mix including labour charges for mixing , laying compaction all tools and planks employed etc., complete complying with standard specification and as directed by the departmental officers

Construction of Granular sub-base of 200mm compacted thickness by providing laying, spreading and compacting of Close graded Material conforming to Grading V of Table 400-1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers withmotor grader o n prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading maintenance of diversion road loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORTH technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work

Construction of Wet Mix Macadam 200 mm compacted thickness in two layers by providing laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying he physical paraemeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mixed material to work site and laid in sensor pavers tc the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer In-Charge of work

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II) / 1981 and as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc.,Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

Reinforced cement concrete Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

For plane surfaces such as recangular or square columns, sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

For circular columns

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

For Additional 1m height (3.3m - 4m)

For Additional 1m height (3.3m - 7.5m)

Providing and Laying M 35 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. Rate to include all leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer in charge.

For Foundation & Basement

Ground floor

Mezzanine

First floor

Second floor

Terrace floor

Providing and Construction of M40 Grade Pavement Quality Concrete of 200mm thickness including dowel joints over a prepared Base Course of PCC layer with 53 grade of cement, coarse and fine aggregate conforming to IS 383, coarse aggregate 25 mm & 12.5 mm Granite/Basalt/Trap metal & clean seived approved sand conforming to the gradation asspecified in Table 600-3 of MORTH clause 602., loading materials to cement conrete batch mix plant of adequate capacity ( normaly 25% more capacity than the paving equipment preferably 120 Cum/hour ) as per approved mix design satisfying the characteristic flextural strength of not less than 4.2 Mpa. Finishing the Concrete surface using Power Trowel including hire charges of Power Trowel, fuel charges, labour charges etc., complete The mix shall be transported to site in transit truck /tippers/ dumpers of 5-6 Cum capacity, laid with a slip form paver with electronic sensor fitted with vibrators shich shall operate at a frequency of 8000-10000 impulses per minute under load with a maximum spacing of 600mm and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, fixing of Dowel bars and Longitudinal tie bars ,joint filler, separation membrane, sealant primer, joint sealant, debonding strip, curing compound as approved, finishing with power trowel to the required grade, level and alignment, textured with texturing machine, finishing etc., making groove cutting for construction joint of size (4 x 10mm) and filling the same with polyurethene sealent, making groove cutting for expansion joint of size (8 x 10mm) and filling the same with polyurethene sealent, providing Isolation joint of 20mm wide to the full depth of the concrete and fixing with isolation pad of 20mm thick and sealing the top with polyurethene sealent to the size of 20 x 20mm and curing (curing shall be as per clause 602.9.12 of MORTH) including cost of all materials, labour, lead and lift, hire charges of machineries , including the initial saw cut and filling of Polysulphide/Polyurethene sealants in contraction, expansion joints etc., complete in accordance with MORT&H technical specification clause No. 602 and with all other incidental charges inclding the trial length and as per the direction of the Engineer-In-Charge of work. (Reinforcement and Dowel bars shall be paid under relevant item)

Post Tensioning Work: Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required.Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing Fly ash Brick (230 x 110 x 75mm) masonry in Cement Mortar 1:5 (One cement and Five M sand) in foundations, basement and superstructure using Fly ash Bricks of size 230x110x75mm etc. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

For Foundation & Basement

For Ground floor

For Mezzanine floor

For First floor

For Second floor

For Terrace floor

Supply and constructing Flyash Brick partition wall 115mm thick in Cement Mortar 1:3 (one cement and three M sand) 11.50 CM thick using using Fly ash Bricks of size 230x110x75mm including both side plastering with CM 1:5 12mm thick and using hoop iron reinforcement if found necessary and hoop iron shall be supplied to the department at free of cost etc., complete as directed by the Engineer in- charge.

For Ground floor

For First floor

For Second floor

For Terrace floor

Special ceiling plastering and finishing all RCC exposed surfaces such as RCC slabs, sunshades, canopies, stair case steps, landing slabs etc with CM 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing necessary CM nosing, beading as per size specified wherever necessary using the same mix etc., complete complying with standard specification and as directed by the Departmental Officer.

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications.

Waterproofing: Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the UGT/ OHT tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for 3 times a day for 5- 7 days. Followed by applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti algae, antifungal, Non-toxic, hygiene cum damp-proof coating Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA, having mixing Ratio (Base: Hardener: Water) – 1:1:1 to be applied @ 0.35 Kg/m2 in 2 coats. Ensure that this coating is applied over the protective plaster. The Waterproofing material shall have Specific Gravity: 1.2, Water vapor permeance: 244.48 g/m2/24 hrs, as per IS 7809/Pt 2/1977, Adhesion strength: 2 N/mm2 as per ASTM D 4541: 02. The finished cost to include surface preparation completely as per specification.

Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (1 Liquid: 2 Powder), to the RCC surface like bathroom, toilet, balcony & utility area applied @ 1.7kg/m2 in 2 coats to achieve 1mm DFT, having Elongation at break >50% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80 N/mm2 as per ASTM D 4541, crack bridging upto 1mm as per ASTM C 836, Water penetration (5 bar pressure) as per BS EN 12390. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

PVC mould CI Steps for Sump

Painting the new plastered walls with two coats for Interior Plastic Emulsion paint approved quality and colour over a priming coat, with two coats of wall putty including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting the wall with Texture Finish Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete as per standard specification. (Scratch/rain plaster)

Providing Microcement Plaster with Following Specifications Microcement is prepared from a powder component (microcement base for the preparation of the works and microcement fine for the finish) and a liquid component. These two components must be mixed homogeneously according the following proportions: • Microcement Base (microcement base: preparation mortar) 10 kg of powder must be mixed with 3 liters of concentrated liquid • Microcement Fine (microcement fine: finishing mortar): the mix will be done as follows; for 10 kg of powder approximately 4.5 liters of liquid will be used The mortar must be prepared as follows: 1. Pour little amount of resin (component B) into a container, then add the quantity of pigment required according to the amount of microcement to be used, and then mix them up until a uniform colour is achieved. 2. Pour gradually the Microcement powder (component A). Add the powder as the product is mixed with a slow speed mixer drill. 3. Mix for at least 2 minutes until the mortar is smooth and free of lumps.

Painting the new Iorn work with two coats of Ready Mixed Enamel Paint of aproved quality and colour over the existing priming coat including the cost all materials etc.,complete, in all floors and as directed by the Departmntal Officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Providing and fixing Vertical blinds , quality of approved make fabric made of 100% polyester woven fabric thickness 0.40mm with virtually maintenance free having plastic bottom chain thickness of chain-0.50mm and diameter-3mm, Plastic with metal bottom and suitable coating on exterior, including all fixtures and fittings complete in all respect as per design/color/shade including requisite installation brackets etc as required for installation at site with anchoring arrangements complete.

Providing and installing Invisible Grilles at designated locations, comprising 2mm diameter 316 marine-grade stainless steel cables with a transparent nylon coating, tensioned and anchored within powder-coated aluminum frames of approved color. The cables shall be spaced at intervals of 2, 3, or 4 inches, as specified, to ensure safety without obstructing views. Each cable must possess a tensile strength capable of withstanding loads exceeding 400 kg, ensuring robust protection against intrusions and accidental falls. The installation shall maintain the aesthetic integrity of the building facade while providing unobstructed views from windows and balconies. All materials used must be corrosion-resistant and suitable for coastal environments, ensuring durability and minimal maintenance. The scope of work includes the provision of all necessary materials, labor, fabrication, transportation, scaffolding, and installation to complete the task as per the drawings, specifications, and directions of the Engineer-in-Charge.

Providing Teak wood wrought and put up for frames of doors, windows and ventilators and any other similar joinery works including cost of country wood scantlings and labour charges for manufacturing the frames and fixing hold fasts and fixing in position etc. for all lengths as per architect designs.

Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Providing and installing manual bi-folding glass doors at designated entrances, comprising 12mm thick clear tempered glass panels with polished edges, set within powder-coated aluminum frames of approved color. Each door system shall consist of four panels, each measuring 900mm in width and 2400mm in height, folding to one or both sides to maximize clear passage width. The door hardware shall include heavy-duty stainless steel hinges, ergonomic D-type stainless steel handles on both sides, and a multi-point locking system with concealed flush bolts. The top-hung aluminum track system shall utilize stainless steel rollers to ensure smooth and silent operation, while EPDM rubber gaskets along all edges shall provide effective weatherproofing and dust resistance. Installation shall involve securing the door system within prepared openings using appropriate stainless steel fasteners, ensuring precise plumb and level alignment. All joints are to be sealed with silicone sealant to prevent water ingress. The scope of work includes the provision of all necessary materials, labor, fabrication, transportation, scaffolding, and installation to complete the task as per the drawings, specifications, and directions of the Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/ Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 100mm of required thickness with necessary full body threaded star headed counter sunk S.S screws/ welding wherever required necessary etc all as per direction of Engineer-In- Charge.30 mm thick

Steel Doors: Supply and installation of operable steel door of Tata Pravesh or equivalent of design with vision panel and dimensions as per Architectural Drawings inclusive of delivery at site and installation. The doors must conform to the following specifications: HSN Code: 7308 Frame profile: Single rebate Frame type: Regular Frame dimensions: 100 x 58 Frame sheet thickness: GI 1.2mm Frame Infill: Puff Shutter thickness: 46mm Shutter sheet thickness: GI 0.8mm Shutter Infill: Honey comb craft paper Hardware set (GEZE or Equivalent): a) SS 304 Ball bearing hinges; 4 x 3 x 3mm - 3 Nos b) Rack and Pinion door closer with link arm - 1 No c) D handle on both sides - Dia 19 x 254mm - 1 No d) Mortise dead lock with Euro profile cylinder - 1 No

Aluminium Framed Glass Doors: Providing and fixing of powder coated aluminium fixed cum openable door using Jindal/equivalent 63x38x1.5mm thick box section for outerframe, 48x44x2mm thick section for door verticals, door top & 100x44x2mm thick section for door bottom, glazed with 5mm thick clear toughened glass, with necessary aluminium glazing clips, EPDM gaskets, lock, 22mm dia 300mm long SS handle, silicone sealant and other necessary hardwares etc. inclusive of delivery at site and installation. Design and size of doors as per Architectural Drawings. Door types: MD1, MD2, MD2A, D2

Supplying, Fitting, Fixing and Installation of Merino Besco TITAN 12MM BOX UP series cubicles (or approved equivalent make) of width and depth as per specifications/ site drawings.Cubicle height to be 2100 mm and/or as perrequirement/site conditions. Length & breadth of the cubicles shall be as per requirement and /or as per site conditions. ITEM-DESCRIPTION:- Made from solid grade compact high pressure laminate as per IS:2046 and EN 438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of Kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fibre impregnated withthermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along withanti-bacterial properties. Panels have a black corethat when machined, presents a distinctive black edge. Doors: All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed tothe pilasters. Stainless steel made coat hook and lockset are provided with each door. All the doors will be routered at the vertical ends and the rubber spongelining will be incorporated at the routered ends. Pilasters: All pilasters will be made of 12 mm thick Merino HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Pilasters will be anchored to the floor using steel made Lbrackets and box up fixtures are used for covering the floor anchored mechanism. All pilasters will be routered at their vertical ends to facilitate closure of doors. The bottom gap is 100 mm. Dividers: All intermediate partitions or dividers will be made of 12 mm thick Merino HPL compact laminate panels. They are affixed with stainless steel made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panelsto be as per drawing / as per requirement/ site conditions. HARDWARE & ACCESSORIES: • Top rail is made of stainless-steel grade 304. A thin plastic film pasted for surface protection.Dimension is 55mmx42mmx1.6mm-Tee. • Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8mm-Tee. • Wall joinery section with hamming profile made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 21mmx16mmx0.8mm-Tee. • Fixed front panel to be anchored to floor with L Bracket of SS and covered with SS 316 Grade Box Type plate from all directions with 100mm clear Height from ground. Surface finish to be matt-type. • Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacquer coated. • Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt-type. • Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt-type. • Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type. • Anti-noise rubber padding of thickness 2 mmand width 10 mm • Stainless steel grade 304 screws. Material: Merino Make or Approved Equivalent Mode of Measurement: - From finished floor to top of cubicles, as and where found the physical height of the finished structure . No wastageshall be considered for measurement purpose. Merino Make or Approved equivalent material

Paving the floor with Granite flag stone of varieties size over a cement mortar bed of 20mm thick using cement mortar 1:3 (One Cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angkes with minimum possible width of joints with white cement mixed with matching colouring pigments etc.,

Providing and laying Concrete Flagstone 600x600x65mmsize over a cement mortar bed of 20mm thick using cement mortar 1:3 (One Cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angkes with minimum possible width of joints with white cement mixed with matching colouring pigments etc.,

Supplying And Fixing Rubber Moulded Interlocking Paver Blocks Against Available Edge Restraints 83 mm Thick of Approved Design And Pattern of Strength 40 N/Sq.m. 10 mm Iss Metal With Minimum Cement Content As Applicable To M 40 Grade Concrete As Per Is-456-2000 Manufactures By Mechanical Or Hydraulic Machine Using Vibro- Compaction Process And Laid Over 50 mm Thick Laying Course (Bedding) Crushed Stone Sand (M Sand) Well Compacted By Plate Compactor With A Joint Width of 2 mm To 5 mm Including Filling of All Joints With Crushed Stone Sand (M Sand) And Compacting The Paved Surface With Plate Compactor Two Or Three Times Until All The Unit-To- Unit Joints Are Completely Filled With Crushed Stone Sand (M Sand) And Trimming The Edges Neatly Including All Labour Charges And Plate Compactor Charges Etc. Complete(Cost Inclusive of Crushed Stone Sand (M Sand))

Supplying and laying Grass Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And All Taxes Including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining Etc Complete .

Providing and laying of Black Granite Cobble Stone flooring of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 1200x2400x9mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Executive Engineer before use on work

Paving the floor with Sandstone of approved quality and colour, size and of approved make, in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality should be got approved by Executive Engineer before use on work

Paving the floor with Limestone of approved quality and colour, size and of approved make, in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality should be got approved by Executive Engineer before use on work

Paving the floor with Nexion full body vitrified anti-skid tiles of approved quality and colour, size 1200 x 600 x 10 mm and of approved make, in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality should be got approved by Executive Engineer before use on work

Paving the floor with design Antiskirt Vitrified tiles (colour and shade as directed) of size 600 mm x 600 mm x 8 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Paving the floor with design Antiskirt Ceramic tiles (colour and shade as directed) of size 305 mm x 305 mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement.

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and fixing Dadooing the wall with Vitrified tiles of approved quality, colour and design joint free of size 600x600x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying with best quality the following materials of Jet Black Granite Slabs (Super Fine Polished with Machine Cut Edges) of sizes 4’x2’ and above 18mm to 20mm thick Thick including cutting and edge polishing to be set in CM 1:3 (1 of cement : 3 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Nosing for Granite Slab - Single Nosing

Nosing for Granite Slab - Double Nosing

Nosing for Granite Slab - Grooving the Granite slab

Weathering course-using Concrete broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers.

Finishing the top of roof with one course of Solar Reflective ceramic tiles of size 305 mm x 305 mm x 7 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person

Supply and laying with best quality PU tactile tile stud of size 300 x 300 x 15 mm

STAINLESS STEEL 304 GRADE WARNING TACTILE STUD - STAINLESS STEEL JINDAL MATERIAL WITH TC 35mmx25mmx4.5mm Stud with 6mm dia 12mm length stem, Top concentric ring pattern, stain mat finished (Make Super Steel Impex) 1 RMT 108 pics with Stud installation charges -Marking, drilling and fixing with epoxy chemical

STAINLESS STEEL 304 GRADE DIRECTION TACTILE STRIPS -STAINLESS STEEL JINDAL MATERIAL WITH TC 280mmx35mmx4.5mm Stud with 6mm dia 12mm length 3 stem, top leaner pattern, stain mat finished (Make Super Steel Impex) 1 RMT 12 pics with Strips installation charges -Marking, drilling and fixing with epoxy chemical

Supply and fixing of acrylic braille toilet signage of size 300 x 300 mm

Supply and fixing of SS 304 series Braille map plate of size 450 x 300 mm

Supply and fixing of precast customized concrete light up 3 seaters of M30 grade

Supply and fixing of WPC pergola with pillars and rafters (as beams) made with wood and polymer with different surfaces like sanded or brushed or embossed pergolas or a perfect replacement of conventional wood structures available in customised wood alike colours, size 12 x 12 x 9 feet, this format can be multipled with more such units for longer installation. This comes with polycarbonate roof covers

Supply and fixing of terracota tile cladding from novacotta tile of approved size

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc ROLLING SHUTTERS (WITH ISI MONOGRAM) Gear Operated Type (from 8 sqm. to 12 sqm. Area)

Supplying and Fixing of CNC cut perforated Enclosure for EB transformer and EB pillar Boxes by using CNC MS Sheet (2mm thick), door hinged with vertical support of 80X40 mm Tubular Post including horizontal Support and Stiffener (40 x40 x2mm) for MS sheet including Powder coating of all structural members and labor for fitting , welding and transportation of the material from the factory to Site as directed by the engineer - in charge.

Fosroc water-proofing solution for balcony planter box - slurry primer should be prepared consisting of 1 volume Nitobond SBR to 1 volume clean water to 3 volumes fresh cement. To obtain a smooth consistency, the cement should be blended slowly into the premixed liquids. The slurry primer should be stirred frequently during use to offset settlement.

Aluminium duct louver system - non-retractable slatted blind with aluminium louvers and doors . These louvers and doors are made from high-grade extruded aluminium, and have a width 88 mm. Duct louver and doors system is suited for all kinds of internal and external installations; horizontal, vertical, sloping, and upside down. Aluminium louvers are usually movable doors and also be placed in a fixed position.

Supply and fixing of Stainless-Steel recessed Manhole covers - Medium Duty - The Medium Duty S.S recessed Manhole Cover will be Suitable for Slow Moving Wheel Load, Like Footway, Pedestrian and Car Parking Deck, etc., size - 750 x 750 mm

Construction of Rain water Recharge well (1200mm dia) as per consultant drawing with necessary connections, Earth work-digging the well for recharge well supply and installation of Reinforced concrete Rings -4 feet OD & 1 feet Height 75 MM Thick - 20 no's supply and installation of einforced concrete slab 4 feet in dia. 200 mm thick, and 25 mm perforated 8 mm mild steel rods used for reinforcement-1" Perforated - 1no's supply and installation of Reinforced concrete closing slab 75 mm thick, 8 mm mild steel rods used for reinforcement with 600mm x 600mm Square HEAVY DUTY PERFORATED manhole cover Filtration Media Installation For recharge Well Unit 40 mm crushed stones-0.5cum, 20 mm crushed stones- 0.5cum, Brick Bats-0.5cum,fine sand 0.5 cub mtr Mixture of Brick Bats Shifting of excavated earth to the approved/authorised dumping yard as directed by the authorities/Site in charge. Drilling a bore well-200mm dia by high speed compressor-4MTRS, supply and installation of 110mm PVC PIPE PN-6-4 rmtr, 110mm PVC PIPE PN-6 Perforated with 10 mm Zigzag holes to easy percolate the water-4 mtr, 12mm Gravel Packing between bore well hole and PVC pipe and Inserting into the Bore Well- 4 mtrs. supply and installation of 180GSM Gio-fabric sheet to cover V-Wire screen, supply and installation of V WIRE SCREEN- 0.75 mm Slots. SS-304 Material -0.5 mtrs Height 6" diameter Shifting of excavated earth upto 1000mtrs as directed by site in charge (the well sholud be got approved by the concern department Engineer before use on works)

Fixed Glass and doors with floor spring, fittings and locks - Consisting of 12mm clear toughened glass fixing with proper metal fabricated frame work and spacer with silicon grouting, double side tape, edge grouting & etc with all the necessary fittings upto all height including scaffolding all complete as shown in attached drawing as per the direction of Engineer-in-charge.

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete.

Providing fixing and pasting Wall paper as per design & details. The item includes making POP base to get a uniform smooth surface. (base Price Rs. 100/ sqft.without taxes) The fixed area of wall paper shall be considered for payment and not the area of procured material.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/ltr and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane:

Art work as per the direction of department official, over Oil Painting with first class quality and approved colour including a priming coat with thorough scrapping clean removal of dirt., etc., complete and including necessary plaster of paris, putty, etc., wherever required (Relevent ISI STD), including putty works.

Manufacturing, Supplying and Fixing of Stainless Steel (brushed) Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 3.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance,welding charges, electrical charges, etc. complet

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Providing two legged scaffolding using 15cm dia casuarinas post of 4.0 m over all length of (3 M Height+0.5 M over all length (3.0M height +0.5m projection +0.5m in to the ground ) the distance between the two rows being 1.25M and the spacing of posts being 2.0M in both the rows with two horizontal posts with 0.5M overlap on either side and braces at 2.0M centre to centre including longitudinal and traverse middle braces to step up and transverse middle braces to step up and providing a plat form with country wood planks of 40mm thick and 1 M width ,etc in a complete form using coil and nails (Rate for an initial height of 3.0M and length of 1 M)

Scaffolding charges for every additional height of 2.5 M height over the initial height of 3 m.

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Fabricating supplying and fixing of 8mm thick Calcium Silicate Board Designed and Perforated for False Ceiling

Fabricating supplying and fixing of roof with Poly carbonate sheet of 6mm thcik with any colour or any other approved design and to be fixed with shelf tapping screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed.

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Supplying and fixing G.I. Gutter made of 20 B.W.G. galvanised iron sheets and G.I. valleys made of 18 B.W.G. galvanised iron sheets including fixing,etc.,complete.(ISI STD)

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Providing and painting all steelwork with (i) one primer coat of inorganic zinc silicate (min. Vs 62%) 50 micron (ii) one coat of epoxy HB MIO brown (min Vs 55%) 75 micron (iii) one coat of polyurethane paint (min. Vs. 40%) 40 microns including all material,one coat of epoxy HB paint (min. Vs 60%) 100 microns (iv) labour, scaffolding etc. The surface shall be shot blast to SA 2.5 standard using grit. The paint shall be applied as manufacturer's specifications and the item shall include necessary testing, test certificate etc.

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames. Glass: 5mm reflective Saint Gobain OR equivalent

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying and Fixing English Stainless Steel Letters 25cm (10”) Providing and fixing of Stainless steel grade 304 golden letters in English with Main letter of minimize size 175 mm with 25 mm raising. The rest of letters shall also be of Stainless steel grade 304 in golden with minimum size of 150 mm, 25mm raising. The letters shall be fixed with the help of stainless steel studs on existing granite wall which shall not be visible from the front. The stainless-steel studs shall be properly grouted with suitable sealant. The logo shall be of minimum dia 750 mm and shall be perforated one with cutting of balance vacant space leaving the matter in logo. The letters of name in logo shall be engraved/etched in black letters over golden stainlesssteel sheet with heating process. The work shall be executed to the satisfaction of Engineer- in-charge.

Providing and fixing exterior-grade soffit lining using VOX Soffit Infratop Basalt Oak panels of size 2700mm length, 340mm total width, and 300mm usable width, made of high-quality co-extruded PVC with wood-textured finish, ensuring durability, weather resistance, and low maintenance. Panels shall be fixed over a wooden or metal sub-frame using appropriate screws, allowing for thermal expansion and contraction as per manufacturer’s recommendations. Installation shall be carried out as per the manufacturer’s specifications, including maintaining proper ventilation gaps, securing panels with recommended fasteners in pre-designated slots, and ensuring a uniform finish. The rate shall include all materials, labor, scaffolding, cutting, and fixing to complete the work as per site requirements and as directed by the Engineer-in-Charge.

FALSE CEILING WITH GYPSUM PLAIN TILES Providing and fixing true horizontal level false ceiling using SAINT - GOBAIN GYPROC or Equivalent make with 24 mm Grid system using hot dipped galvanised Steel Section, exposed surface chemically cleaned caping prefinished in backed polyestar paint wall angle of size 24mmX24mm used in the periphery of the ceiling fixed to the wall partition R.C. Column bandwalls with the help of screws at 600mmc/c. Main runner of size 32X24mm suspended at 1200mm c/c max by using securely fixed to the structural soffit of R.C.C. slab by using 6mm Nylon Rawl plug at every 1200mm (Max) and 1200mm long Cross Tee of size 24X24mm to interlocked between Mainrunner at 600mm c/c (max) to form a grid of 1200mmX600mm. 600mm long Cross Tee of size 24X24mm is inserted to form a grid of 600mmX600mm and finally tiles laying with 12mm Gypsum plain Tiles

Providing and fixing 50mm thick GFRC (Glass Fiber Reinforced Concrete) Jalli with approved color and design; fabricated using type i or ii cement, sand in 1:1 ratio, and chopped ar glass fibers (2–3% by weight for premixed gfrc or 4–6% for spray-up gfrc); acrylic polymer emulsion with 5% acrylic solids by weight of cement; vcas pozzolan to replace 10–25% of the cement; addition of superplasticizer, water reducer, or polymer-curing admixture as required; color to be integrated in the face coat using dry or liquid pigments; panels to be factory-made with controlled curing for consistent quality; rate inclusive of all supports, stainless steel anchors and hardware, grouting, expansion joints with weather-resistant silicone sealant, crane and hoisting charges, scaffolding, and specialized labor; application of two coats of approved acrylic sealer; sealing of cracks and chips due to handling or construction; final cleaning and finishing complete

Supplying and fixing Partition with powder coated Aluminium frames with Bottom Double glass with centre rattan cane and top fluted glass including cost of Material, Labour, lead etc., Complete.

Providing & fixing in position Wall and Column Panelling 18 mm thick WPC Board finished with 1 mm thick laminate with approve colour as per direction of the Architect.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

The supply and installation of a welded metal mesh fence with a mesh opening size of 50mm x 200mm, fabricated in panel dimensions of 1560mm (h) x 2500mm (l). The panels shall be securely fixed to supporting posts of 1600mm length, spaced at 2560mm center-to-center (c/c). The posts shall be anchored to the ground using M12 anchor bolts of 150mm length, ensuring stability and structural integrity. All materials used shall be corrosion-resistant and conform to relevant industry standards for durability and longevity. (nitin orion panel)

Providing And Fixing of Flexible Spring Post/ Tubular Marker Made Up of Polyurethane Used To Divide Opposing Lanes of Road Users Shall Be Flexible In Nature. Tubular Marker Having Minimum Height 700mm Shall Be Having Minimum 3Inch Reboundable Work Zone Retroreflective Sheeting Class A (Type-1) As Per Astm 4956 S2. Application of Tubular Marker Shall Be Done As Per Irc Sp 55-2014. Test Report For Type I Reboundable Sheeting And 1 Year Warranty For The Product To Be Provided. Logo / Information Shall Be Digitally Printed On The Retro Reflective Sheeting.

Providing And Fixing Reflective Road Studs of Category a Raised Pavement Markers Made Out of Poly Carbonate / Methyl Methecrylate /Abs Moulded Body Conforming to astm D 788 And Reflective Panels With Micro Prismatic Lens Capable of Providing Total Internal Reflection of The Light Entering The Lens Face With Retro Reflectance And Chromaticity Values Conforming to astm D4280. The Reflective Raised Pavement Markers Shall Also Confirm To The Morth Circular No Rw/Nh. 33023/10/97- Do.Iii Dt 11.06.97. The Height, Width And Length Shall Not Be Less Than 15mm, 90mm And 100mm And With Minimum Reflection Area of 13 Sq.m On Each Side And The Slope To The Base Shall Be 35+/-5Degree Each Reflectors Shall Have A Cil Not Less Than Values Specified In Table 2 of Said Morth Circular. The Strength of Deteachment of The Integrated Cylindrical Shanks, (of Diameter Not Less Than 19+/-2mm And Height Not Less Than 30+/-2mm) From The Body Is To Be A Minimum Value of 500Kgf. Fixing Will Be By Drilling Holes On The Road For The Shanks to Go Inside, Without Nails And Using Epoxy Resin Based Adhesive As Per Manufacturer’S Recommendation And Complete As Directed By The Engineer.The Marker Shall Support a Load of 13635Kg Tested In Accordance With Astm D4280 And Confirming to Irc 35-2015 Guidelines And .2 Year Manufacturers Warranty For The Satisfactory Field Performance To Be Submitted To The Engineer Incharge For Payment Processs As Mort&H Specification 804 Etc., Complete

Providing And Fixing of Retro Refelctorised Cautionary,80 cm X 60 cm Rectangular Mandatory And Informatory Signs (Without Definition Board) Made Out of High Intensity Prismatic Grade Sheeting Conforming to Type – Iv Standards of Irc 67 . 2012 And Astm D 4956 – 09, Specification And Fixed Over 2mm Thick Aluminium Sheet Fixed Over a Back Supporting Frame of 25mm X 25mmx3mm. Mild Steel Angel And Supported On A Mild Steel Angel Post 75X75X6mm With A Clear Height of Not Less Than 2.10M From The Ground Level To The Bottom of The Sign Board And 0.60M Below Ground Level. The Sign Post Should Be Painted As Per Irc 67-2012 And Firmly Fixed to The Ground By Means of Properly Designed Foundation With M15 Grade Cement Concrete 45mmx45cmx60cm Size Including Cost And Conveyance of All Materials, Equipment, Machinery And Labour With All Leads And Lifts, Loading Charges Necessary For Satisfactory Completion of The Work As Directed By The Engineer In Charge. High Intensity Retro – Reflection Sheet Shall Consist of Minimum Coefficient of Retro- Reflection As Per Table 6.6 of Irc 67X2012. The Retro Reflection Sheeting Shall Be Covered Under 7 Years Warranty Issued For Field Performance And A Certified Copy of Three Years Outdoor Exposure Report Shall Be Obtained As Per Irc 67-2012 (As Per Mort&H Specification No.801)

Supply and fixing of Unbreakable Convex Mirror 100 cm For Road Safety with Installation Kit Rearview Radar Mirror

Supply and fixing of parking safety pillar guard, rubber corner bounce shaped guard with yellow reflective tapes for high visibility emergency reflective sign, size 1000 mm

Supply and fixing of SS 304 series Braille indicators for hand rails, size 30 x 160 mm

Providing And Laying of Hot Applied Thermoplastic Compound 2.5 mm Thick Including Reflectorising Glass Beads @ 250 Gms Per Sqm Area, Thickness of 2.5 mm Is Exclusive of Surface Applied Glass Beads As Per Irc:35 The Finished Surface To Be Level Uniform And Free From Streaks And Holes Etc Completed As Per Mort& H Specification No.803

Reinforced Cement Concrete Bollards with M20 grade concrete and 150mm dia 4 Nos of 10mm dia TMT of overall size 800mm, 100mm projection of TMT Roads at the bottom of the Bollards beyond 800mm for anchor. Black pigment at 4.5 percent weight to cement will be used. Two Strips of Reflective 3M Sticker of width 40mm, including transportation and fixing charges etc, complete.

Providing and laying precastsaucer type drain of size 600x300 x 50mm with M30 GRADE concrete including the Cutting of the existing bituminous surface of 10 cm thicckness and PCC of 1:3:6 for leveling and maintain the gradient to drain the water from raod to Storm water Drain etc and complete

Supplying and laying precast a size 300x300 x 60mm thick with perforated hole for perlocation of water and using M30 GRADE concrete inclusive the conveyance of the material form the Manufacturer factory to the site al lead of average 40km and including the sectioning, levelling ,laying the good earth for maintain the uniform top level and compacting with earth rammer etc and complete

Custom concrete cattle grid M40 Grade standard and maintenance free grids range in weight capacity more than 40 tonne, perfect to suit varying levels of traffic and heavier vehicle access

Providing and laying Woven Geotextiles of Type-I on the pre pared subgrade as the separator cum reinforcement with nec essary overlap as per drawing and as per MORTH Specification 702

Providing And Fixing All Side Machine Cut Granite Stone Using 0.75M Height 0.100M Thick And 1.0M Length Granite Stone Without Fragmentation For Centre Median Including Cost And Conveyance of Granite Kerb From Available Source To Work Site Including Labour Charges For Fixing The Granite And Pointing With cm. 1:3 And All Other Incidental Charges Etc. Complete.

Providing And Fixing Machine Dressed Grey Granite Slab All Sides Machine Cut of Size 0.60 M X 0.60 M Size And 50 mm Thick Granite Slabs For Platform(Pavement) Including Cost And Conveyance of Granite From Available Source Including Labour Charges For Fixing The Slab In Position To The Line Level And Gradient Including Pointing With cm.1:3 And All Other Incidental Charges Etc. Complete

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Supply and providing Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

75mm dia

110mm dia

160mm dia

50mm dia

Internal Water Supply - CP.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

15mm dia

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

Supplying and fixing in position best quality approved make white glazed earthenware Oval Shape Wash Hand Basin of size 560 x 450mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position indian make bewelled edge mirror of approved quality and brand of size 600 X 450mm wth necessary plastic back, PVC frame with bottom stand of approved colour with brass screws,rawal plugs etc., complete complying with standard specifications

Supplying and fixing best approved quality C.P.Soap Tray of size 150mm X 100mm including cost of Teak Woodplugs, brass screws complete complying with standard specifications.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications

Suppling and fixing in position 15mm diameter brass / C.P screw down tap / pillar tap / swan neck tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary. C.P screw down tap

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing the best quality approved make of bip cock with C.P. health faucet wall hook one metre long flexible tube, angle cock with wall flange including cutting and making good the walls wherever required etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Executive Engineer before use on work.

Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mmwith all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia ‘B’ Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc.

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete - Depth per cm

Supplying & fixing in position first quality & approved variety of 50mm dia C.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

25mm dia

32mm dia

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit etc. using only calyx rigs.

Reaming from 200mm dia pilot bore to 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992

200mm dia CS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supplyinga dn fixing 5.0 HP Monoblock Pump including all accessories

Supplying and Fixing Liquid Soap dispenser - Parryware- T6513A1 or Equivalent

Supplying and fixing PARTITION MOUNTED SANITARY NAPKIN DISPOSAL Color: Silver Installation Partition-mounted Operation Manual Finish :Satin Shape: Rectangle Capacity 4.7 Liter. Product Dim. L 330 x W 107 x H 505 mm

Supplying and fixing Flash touch-free infrared hand dryer with 1150W rated power & carbon brush motor. Jaquar - HDR-SSF-AK2807 or Equivalent

Supplying and fixing Paper holder with flap recessed type (Stainless Steel) Jaquar AHS-1553 or Equivalent

Supplying and Fixing manhole cover SFRC

600mm x 600mm

750mm x 750mm

900mm x 900mm

Supply, Fixing & commissioning of 5004 PLUS SAM PRS Series Rotor pop up sprinkler full/part circle having radius of 6.7m - 12m @ 2.5 - 4.5 bar with discharge of 0.09 - 0.61 ltr./sec. the sprinklers having Arc Adjust thru Top Cover w/ Std. Screwdriver The sprinkler is gear driven rotary type with having 3/4" bottom inlet. Oversized wiper seal, Rain Curtain technology, gentle close-in watering and Self-flushing arc adjustment port and also having tapered riser stem with Wiper Seal The sprinkler shall have Plus (PL) Flow shut off, 45 psi pressure regulator with flow optimizer technology, internal Seal - A - Matic device which prevents low internal Seal - A - Matic device which prevents low head drainage (upto 3.1m) & hence puddling & erosion. The body of sprinkler is of non - corrodible, heavy duty, ABS plastic. O-ring Slip Clutch, Racheting Slip Clutch, Side Inlet Available 6" and 12",Turret-mounted ID Plugs, Flow Stop Available, Non-potable water indication available etc., complete including installation charges.

Supply of 1/2" Pop up connecting swing joint assembly. The tubing shall be made of polyetylene having wall thickness of 2.3mm ,a working pressure of 5.5 kg/cm2 at 430C and a surge pressure of 16.6 kg/cm2. The fittings shall be made of UV resistant thermo plastic.SA Series including installation charges.

Supply of 3/4" Pop up connecting swing joint assembly. The tubing shall be made of polyetylene having wall thickness of 2.3mm, a working pressure of 5.5 kg/cm2 at 43oC and a surge pressure of 16.6 kg/cm2. The fittings shall be made of UV resistant installation thermo plastic.SA Series including installation charges.

Supply of large capacity Disc filter 25 M³ / Hr. including installation charges. (brands like Rain Bird or equivalent)

Flexible polyethelene irrigation pipe 16 mm dia / 2.5 / 1.1 - 1.4 mm CL - II. " Netafim " including installation charges.

Supply of endcap, nipple, start nipple, rubber grommet 16 mm dia. "Netafim" including installation charges.

Supply of Pressure compensated dripper with 2 / 4 / 8 LPH outlet flow. Rain Bird / Netafim make including installation charges.

Supply of Micro sprinkler of half & full circle with 55 LPH output flow with necessary micro tube & stake. Rain Bird / JISL make including installation charges

Supply and fixing of Sheesham Wood Arm Chair In Rustic Teak Finish with the following Dimensions (In Centimeters) H 77 x W 53 x D 58

Supply and fixing of 3 saeter Southampton Rattan Leather Sofa with the following Specifications. Dimensiomns: 3 Seater: 195cm W x 86cm D x 87cm H, Composed of Solid Hardwood, Comes with a fixed seat and loose back pillow.

ROLLING CHAIRS - Supplying & placing of Mesh chair of Medium Mesh Back Chair, Cushioned Seat, Adjustable Lumbar Support, Gaslift, Synchro Mechanism, Adjustable Arms, Nylon Base. The rate should include Materials lead and lift, cleaning , etc.

OFFICE TABLE - 1555mm x 600mm x 750mm - Supply and fixing of Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. Supported on 19mm BWR plywood clad with 2mm thick HDF duco paint to approved shade finish Flip up wire manager is provided on top. . The table will have one number of drawer and 1 No of storage shutter of size - 402mm x 600mm x 590mm with lockable drawers . Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

Supply and fixing of Swivel chair with soft shapes and nice padding with the following Specifications: Tested for: 110 kg (243 lb), Width: 67 cm (26 3/8 "), Depth: 67 cm (26 3/8 "), Seat width: 44 cm (17 3/8 "), Seat depth: 40 cm (15 3/4 "), Min. seat height: 45 cm (17 3/4 "), Max. seat height: 57 cm (22 1/2 ")

COMPUTER TABLE - 1300mm x 600mm x 750mm - Supply and fixing of Computer Table with Key board drawer and table top, Drawer with 6 lever lock with set o 2keys of non corrosive materials, Sliding of keybaord - Provided with two telescopic channels with balls,

OFFICE CHAIRS - Supplying & placing of The Seat and Back Cushion of the chairs should be pressed on 12 mm hot press moulded ply. The seat cushion of the chair should be 50mm thick with density of 45±2 Kg/m^ polyurethane moulded and back cushion should be 46mm thick with density 33±2 Kg/m^. The polyurethane foam shall be as per manufacturer's specification. The hardness of foam shall be 16±2 kgf as per IS7888 for 25% compression and it should be covered with black or brown fabric shade, The arms of the chair should be black, The lift mechanism should be pneumatic or hydraulic, The tilting mechanism should be adjustable with following features: a. 360° revolving type. b. Single point control. c. Front-pivot for tilt with feet resting on ground ensuring more comfort, d. Tilt tension adjustment. The pedestal should be five legged injection coated with black nylon polyurethane and fitted

Supplying & placing of Twin Bed for Junior/ Adults with Guard Rail, Metal Bunk Bed Metal Bunk Bed. Bed Design: Standard Bunk Bed Height x Width: 152 cm x 190 cm (4 ft 11 in x 6 ft 2 in) DIY - Basic assembly to be done with simple tools by the customer, comes with instructions.

Supplying & placing of 5 inch Single Latex Foam Mattress (L x W: 72 inch x 35 inch) Support Type: Latex Foam Comfort Layer: Latex Foam Mattress Features: Orthopedic Mattress

Three seater perforated metal bench -Cross beam and Leg shall be powder coated made of cold rolled steelwith 0.2 ± 0.01 cm thickness. Seat-Back shell shall be 1.2 mm thk powder-coated perforated shell made from cold rolled M.S. sheet 0.12 ± 0.013 cm thickness. The Side Bar shall be made of powder-coated solid steel with inserts. The Shell shall be assembled on the Cross Beam with help of bolts . Seat width- 54.5 cm per seat. Thickness of side bars is 4.5cm & gap between seats is 2cm. Overall Dimensions shall be Seat Height - 40.6 cm, Height - 77.5cm, Width & Depth of Chair as measured from ground - Width-176.5 cm and Depth-71 cm.Dimensions tolerance / variations shall be within +/- 1 cm.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

Supplying and erecting in position of 250 Litres capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works,wherever necessary to install the System in position and intact.

Supplying and fixing Writing WhiteBoard 4′ x 6′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing Writing WhiteBoard 4′ x 4′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing pin up board 4'x6' with the following specifications. Material - Alloy Aluminium Frame, Softboard Core, Premium Flocked Fabric (Velvet) Cloth Surface & Virgin ABS Corners, The back of the board can withstand repeated use and will keep the documents in place with a secure hold. With its strong and elegant frame, the YAJNAS bulletin board will add a perfect feel to the environment of your office, home or school. This board is the perfect blend of stylish and sturdiness that will make a great addition to any space. The Bulletin board corners are designed to be equally strong. The surface will re-close when push-pins are removed, making it long-lasting. Precision riveting of these corners ensures that the edges are properly sealed, thus making the product weatherproof while imparting a seamless finish to it.

Supply & placing of Stainless Steel 304 series three compartment Dustbin of size 1200 x 450 x 900 mm with top cover

Supply & placing of FRP heavy duty three compartment Dustbin of size 1200 x 450 x 900 mm with top cover

Supply & placing of light weight concrete Dustbin of size 450 dia x 900 mm with top cover

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller.

Supply & erection of green wall panel comprising of soilless media along with suitable plants. The frame work structure shall be made of M.S. Tubular Pipe of size 2” X 1”, thickness of 4mm with primer & two coats of anti corrosive paint. Planter box made up of HDPE material. This green wall panel includes drip irrigation PE Pipe, PCJ Dripper, PE Pipe, Connectors, PVC pipe & fittings along with heavy duty PVC Ball Valve and 1 H.P. Motor including installation and testing charges

Supplying and Planting of Cassia fistula tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Sterlitzia nicolia sapling in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Heliconia pssitcorium tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Calathea lutea tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Plumeria alba tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Cymbopogon citratus tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Bermuda grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lobelia erinus shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Brassia variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Schefflera variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hymenocallis littoralis shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lysimachia nummularia including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of zephyranthes -yellow and white including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of ruellia simplex including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Purple Fountain Grass – Pennisetum setaceum 'Cupreum' foliage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Dypsis lutescens (Areca palm) palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of Pennisetum advena 'Rubrum' foliage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Chrysopogon zizanioides including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Miscanthus sinensis including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Agapanthus of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Licula grandis palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of chlorophytum comosum of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Vernonia elaeagnifolia creeper variety in Polythene bag of size 6x7 inch the rate including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge

Planting of Jasminum officinale of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Raphis excels palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of Eucharis grandiflora of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying of Rectangle (3') pot of 90 inch dia and size 45*45 in Centimeter, Various size pots made up of 6mm rod & chicken mesh with cement moulded pots and designer painting with various size plates including loading and unloading charges, transportation, etc as directed by the site in-charge."

Supplying of Plastic pot size of dia 24 inch brown with plates including loading and unloading charges, transportation, etc as directed by the site in-charge.

LT CT TNEB METER BOX: 'Supply, Installation, testing and commissioning of compartmentalised LT CT 3Phase, EB Metering box of outdoor weather proof type with MS mounting stand, Copper busbars with supports, Test Terminal Blocks, CTs, Internal control wiring etc., as per local TNEB standards. Connected Load : 240 kW / Demand Load : 145kW

Supply and fixing of 400A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

MAIN LT PANEL: 'Supply, Installation, testing and commissioning of 3Phase, 415Volts, Main LT Panel board of Indoor, Cubicle floor mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base frame, double internal earthing arrangements, 200Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: EB Incomer : 1 No. 400Amps, 35kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM DG Incomer: 1 No. 400Amps, 35kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Common C/O Incomer: 1 No. 400Amps, 4Pole Automatic Changeover Switch with EB ON and DG ON LED Indication lamps Metering : 2 Set of RYB LED Indication lamps 2 Nos. of Multifunction Meter with RS 485 2 Set of Current Tranformers (400/5A, Cl-1), 1 No. 400/5A CT for APFCR 2 Set of Control MCB and Electrical Interlocking between EB & DG Incomers Outgoings: 1 No. 400A, 35kA, TP+N, TM MCCB with Ext. RHOM (Fire MCC) 5 Nos. 200A, 25kA, TP+N, TM MCCB with Ext. RHOM (APFCR, Sub-Panel-1 & 2, Spare) 2 Nos. 100A, 25kA, TP+N, TM MCCB with Ext. RHOM (TPDB-2 & Spare) 7 Nos. 63A, 25kA, TP+N, TM MCCB with Ext. RHOM (PDB-1 to 2, Ex.LDB, Lifts & Spares) 3 Nos. 32Amps, DP MCB with 1Phase Energy Meter (for Shops)

SUB PANEL - 1 & 2 (First Floor & Second Floor) : 'Supply, Installation, testing and commissioning of 3Phase, 415Volts, Sub Panel Board of Indoor, Cubicle floor mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base frame, double internal earthing arrangements, 200Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: Incomer : 1 No. 200Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Metering : 1 Set of RYB LED Indication lamps 1 No. of Multifunction Meter with RS 485 1 Set of Current Tranformers (160/5A, Cl-1) 1 Set of Control MCB Outgoings: 3 Nos. 100A, 25kA, TP+N, TM MCCB with Ext. RHOM & Digital kWH Energy Meter 2 Nos. 63A, 25kA, TP+N, TM MCCB with Ext. RHOM & Digital kWH Energy Meter 2 Nos. 63A, 25kA, TP+N, TM MCCB with Ext. RHOM (PDB-3 & Spare) 1 No. 100A, 25kA, TP+N, TM MCCB with Ext. RHOM (Spare) 3 Nos. 32Amps, DP MCB with 1Phase Energy Meter (for Shops) 3 Nos. 32Amps DP MCBs

APFCR PANEL - 75KVAR : Supply, Installation, testing and commissioning of 3Phase, 415Volts, 75KVAR rating APFCR (Capacitor) Panel board of Indoor, Cubicle floor / wall mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base /wall frame, double internal earthing arrangements, 200Amps, rating TPN Copper busbars with interconnection busbar, etc., 20KVAR - 63Amps TP MCB - 1 No. 15kVAR - 40Amps, TP MCB - 2 Nos. 10kVAR - 32Amps, TP MCB - 2 Nos. 05kVAR - 25Amps, TP MCB - 1 No.

DG SET - 250KVA with Standard Control Panel (Auto-Start-Stop) : 'Supply, Installation, testing and commissioning of 1 x 250KVA, Silent type Diesel Generator Set complete with suitable size Acoustic enclosure Diesel Engine suitable for Generator application, developing 1500RPM with an overloading capacity of 10% for one hour in any 12continuous hours operation generally confirms to BS:5514, directly coupled to 250KVA at 0.8 Power factor, 415V, 3Phase , 4wires, 50cycles per second self excited, self regulated, with brushless excitation, Alternator generally confirms to BS:5000/IS:4722. DG set shall be complete with radiator, residential type silencer, electronic governor, cable termination box, MS mounting frame, fuel piping, diesel day tank, 24VDC Battery, Battery mounting frame, oil level indicator with gauge board, and all other accessories as per standard specifications. 'Diesel Generator set shall be mounted on cushy foot or similar type of vibration Isolators. The cost of Exhaust pipe shall be excluded in this item. The DG Set shall be suitable for auto-mains failure start and auto / manual operations. The DG Should be supplied with Auto-Start-Stop Control panel with suitable rating switchgear.

LDB-1 to 6, Busbay LDBs, General LPDB, Shops DB & ELDBs : Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

External LDB : Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only.

PDB - 1 : Supply and fixing of 7 segment 8way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 63A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 63A 4pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and separate provision for 6A to 32A SP MCB-24Nos / Isolators (totally 24 nos.) for sub incomers in 3 nos 63A DP MCB segments with label holder and provision for taking up cable for size not less than 35 sq.mm with the following on wall with earth connection only.

PDB- 2 & 3 : Supply and fixing of 7 segment 8way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 63A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 63A 4pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and separate provision for 6A to 32A SP MCB-24Nos / Isolators (totally 24 nos.) for sub incomers in 3 nos 63A DP MCB segments with label holder and provision for taking up cable for size not less than 35 sq.mm with the following on wall with earth connection only.

Anchor & Commercial Shops DB & Mezz TPDB-1 : Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB Isolator as incoming and 3 nos. 32A 3P MCB, 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

General TPDB-2 : Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB, 15 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 3 1/2 core x 185 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 150 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Laying of 4 x 6 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 2 core x 10 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 300mm width and 50mm height with all the fixing accessories

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire and making good of the concealed portion

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 10 sq mm copper wire with painting of suitable colour.

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 6 sq mm copper wire with painting of suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm copper wire and making good of the concealed portion wiith suitable colour

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Primary)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End (Primary)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Secondary)

Supply and fixing of 100Watts LED High Bay ROUND TYPE Lights suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 150Watts LED High Bay ROUND TYPE Lights suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of LED Streetlight fixtures suitable for mounting on street light equivalent to Avenue 100W LED module of LUMILED 5050 LED source of CCT 3000K/4000K/5700K.LED street light fitting with Min system lumen output of 12000 lumens and mounting dia should be 60mm. Luminaire should be with specially designed heat management system to ensure luminous efficacy > 114-120 Lm/w for the system and Power consumption of the luminaire should be maximum 100W. The housing should be of non-corrosive LM6 Pressure Die Cast Housing to with stand extreme environments, it has Anti Dust Exposed Lens. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Luminaire should be IP66 Protection for LED module and IK08 protection and should meet safety and performance and EMI standards. LEDs Make should be from Lumiled / NICHIA / Osram only. which is having CCT of 4000K/5700 K, CRI > 70, SDCM < 5 with useful life of L70B50@75000 Hrs Operating Voltage of driver should be of 120 – 277 VAC.The access to the optical and the gear compartment should be separate. While accessing the gear compartment, the optical compartment should not be disturbed. . .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 3 watt and less than 5 Watt. Mid power And COB’s are not permitted. The luminaire should have an auto shutdown @ 320V and have an auto recovery feature. The Drivers should be a potted driver not a printed circuit board without casing mounted inside the luminaire, it has 6 Kv Internal SPD and Thd < 10 percentage. Luminaire Weight Should be Not More than 6.5 Kg. Submission of LM80-08 for LED source and LM79-08 for Luminaire from NABL Accredited Lab mandatory. The Luminaire and Driver both should be BIS approved and CRS no (R no) of both driver and Luminaire along with BIS certificates should be submitted at the time of bid submission. Make: K-LiTE (Model No. KL-4392) or equivalent.

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

STREET LIGHT Single arm : Supply, Installation Testing and Commissioning of LED Conical street lighting 7 meter pole equivalent to Dragon Lighting pole. Constructed out of Hot rolled steel flat products of grade E250 to IS 2062 : 2011, Finished with Mild shot blast with zinc rich primer and finished using environmentally stable polyurethane based paint/pure polyester powder coated of desired colour .Pole should MS mounting plate Sq.300 x 16mm thick steel of grade E250 to IS 2062:2011 with 4 elongated holes 48 x 24 to suit M20 bolts at CC215mm ensuring firm grouting into the specially designed foundation with Hot dip galvanised foundation bolts. PDC aluminium service door above the base plate shall be provided with the company logo engraved on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. Pole Manufacturer should have ISO 9001:2015, ISO 14001: 2015 & ISO 45001, Pole manufacturer should have inhouse design, Manufacturer and testing facility as per international standard requirements. Make : K-LiTE (Model No. KP -6143) or Equivalent.

STREET LIGHT Double arm : Supply, Installation Testing and Commissioning of LED Conical street lighting 7 meter pole equivalent to Dragon Lighting pole. Constructed out of Hot rolled steel flat products of grade E250 to IS 2062 : 2011, Finished with Mild shot blast with zinc rich primer and finished using environmentally stable polyurethane based paint/pure polyester powder coated of desired colour .Pole should MS mounting plate Sq.300 x 16mm thick steel of grade E250 to IS 2062:2011 with 4 elongated holes 48 x 24 to suit M20 bolts at CC215mm ensuring firm grouting into the specially designed foundation with Hot dip galvanised foundation bolts. PDC aluminium service door above the base plate shall be provided with the company logo engraved on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement Pole Manufacturer should have ISO 9001:2015, ISO 14001: 2015 & ISO 45001, Pole manufacturer should have inhouse design, Manufacturer and testing facility as per international standard requirements. Make : K-LiTE (Model No. KP -6144 or Equivalent.

Supply and installation of IP67 profiles that offers an innovative lighting solution in constrained space which require linear lighting.The LED profiles are made of extruded aluminium and stainless steel mounting tray. The aluminium profile and the polyurethane encapsulation lends to IP67 protection class.Various mounting options are available making it a versatile product for various applications. • Luminaire made of extruded aluminium profile (grade 6063) with stainless steel mounting tray. • Translucent polyurethane encapsulation. • Mounting tray for better cable management with slide fit system. • Suitable for recess mounting. • IP67 connector on both ends and can be easily installed via mounting tray. • Constant voltage LED driver 24Vdc Non integral • Multiple lengths of Profiles. • CCT Option: 3000K * CRI Ra>90 • SDCM ≤ 3 • L80 / B10 @ 60,000 Hrs • For ready use with IP67 connectors * CE Marking, BIS Certified, IK 10, IP 67, UV Shield, LM 80 Compliant, Salt Water Resistant. * Manufacturer to have in-house NABL lab with testing facility of IP, IK, Slat Spray test. * Make : K-LiTE : KL 3621 or equivalent (Form 33 Slim model)

Supply of Smart Multi-Utility Pole with IP 65 Rated LED Luminaire, IP 65 Rated Speaker, Digital LED Display, Cell Phone charging, Projector Lights, Only Provision for EV Charging facility, Height Max. 6 Mtr. Make : K-LiTE The Smart Multi-Utility Pole is an integrated urban infrastructure solution designed to support modern urban needs, such as provisions for EV charging, efficient lighting, and provision for mobile charging, while also allowing for additional smart city functionalities. It is constructed using high-quality galvanized steel or aluminum, ensuring durability and longevity in outdoor environments. The pole stands at a height of 6000 mm, with a base diameter of 245 mm. It is surface-mounted and features a powder-coated finish to enhance resistance against corrosion and weather conditions. 2. Electrical & Functional Features Options at Extra Cost: The pole can be integrates a 7.5 kW EV charger, which includes a control unit, emergency stop switch (64 mm diameter), and an LCD display (80×27.5 mm) for user interaction. Options included by default in Smart Multi utility pole: A dedicated mobile charging point is also provided, supporting both USB and AC socket charging. The lighting system consists of a 120W Waco fixture with a single arm, supplemented by a 50W post-top light with a NEMA socket, ensuring adequate illumination. Additionally, two 18W Nebula projector lights are enclosed within the system. The power input required for the entire setup is 230V AC, 50Hz. 3. Communication & Smart Features As per the project scope, Light Module, Projector Spot Lights, IP Rated camera, Cell Phone charging and IP Rated speaker modules are included and Customizable in this setup. However, provisions can be made for EV Charging, Digital Ad. LCD Display, Wifi Modules for future upgrades if required. 4. Compliance & Certifications The product is designed to meet CE, RoHS, and BIS certification standards, ensuring safety and performance compliance. The pole and its components adhere to an IP65/IP66 ingress protection rating, making them suitable for outdoor applications. Additionally, the enclosure materials conform to an IK08 impact resistance rating, providing durability against physical impacts. 5. Environmental & Operational Conditions: The Smart Multi-Utility Pole is designed to withstand a wide range of environmental conditions, operating efficiently in temperatures ranging from -20°C to 50°C. The humidity tolerance is between 10% and 95% RH, making it adaptable to varying climatic conditions. The structure is also engineered to withstand wind speeds of up to 150 km/h, ensuring stability in high-wind conditions. 6. The Smart Multi-Utility pole is designed for fixed base plate installation, ensuring a secure and stable foundation. All electrical and functional components are housed within enclosures with concealed internal wiring for a neat and tamper-proof installation. An access panel is provided for easy serviceability and maintenance, allowing technicians to carry out inspections and repairs without difficulty. Make : K-LiTE

Supply and erection of 20Watts, 4 Feet LED Fitting with LED (Higher end) end cap, PVC unsheathed copper leads from terminals to the fitting and fixing accessories

Bollard: Supply, Installation, assembling, connection, testing and commissioning of bollard light fixture equivalent to Sleek Vera Bollard 8W LED module of NICHIA 3030 LED source of CCT 3000K/4000K/5700K. Constructed out of Extruded aluminium tube of grade-6063 (with test certificate) Height: 800mm, Dia 100mm 2.5mm thickness, SS fasteners and Pre-treated silicone gaskets. Finished with acid treatment with shot blasting and pure polyester powder coating. Mounting base made of Die-cast aluminium mounting plate Ø100.5 x 4mm thick with 2 elongated holes 15 x 10 to suit M8 bolts at PCD 55mm with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation with Hot dip galvanised foundation bolts. The mechanical resistance of the luminaire is IK08 and with ingress protection of IP65. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40 degree C. Optical grade clear Polycarbonate diffuser with controlled downward light emission, lamp fixed position. Operating ambient temperature range is from -15 degree C to +50 degree C. Driver efficiency >80 percent , power factor >0.95, THD <10 percent , Colour Rendering Index: Ra>80 and SDCM MacAdam step 3. Input voltage of 230-240Vac at 50-60Hz frequency and have an operating voltage of 100-277Vac with Surge protection 2.5KV and have Symmetrical light distribution and simple electronic On-Off driver. The luminaire is BIS and CE certifications. (NOTE: Final wattage capacity, light fixture colour, light Colour Coding Temperature,Fixture sample is to be done and approved by the Design Consultant and Engineer incharge after sampling and mock-up before finalization.) Make : K-LiTE (Model No. KL -5568) or Equivalent.

Supply and erection of Name board lighting using IP65 rated (1X100Watts) LED with connecting wires and all the fixing accessories

Supply and erection of 9Watts, 1feet long, Fancy type wall mounted LED Light fittings with connecting wires and all the fixing accessories

Supply and installation of 12W LED spot light Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass. Mounting earth spike or die-cast aluminium bracket arrangement to facilitate easy installation at any desired location. Swivel range of 0°-90°. Luminaire supplied with 0.5 metre cable length and a IP67 connector & Factory sealed Moisture arrestor protection for Cable Joints. Silicone gasket. Integral constant current power supply. CRI (Ra) : ≥80. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Anti glare visor / Honey Comb Louver assembly. Operating Volatge : 100-300Vac. Power Factor > 0.9, THD <10%, Surge Protection 4kV-6kV, LED Driver efficiency >80%. Beam Angle : 15/25/40. Mandatory CE Marking, BIS Certification, LM 79 report, IP, IK Report from NABL accredited Lab. Make: K-LiTE (Model No. 4067/KL 4268) or equivalent, and to complete necessary accessories and etc to complete the work.

Supply and installation of 8W LED Inground recessed Luminaire made up of pressure die-cast aluminium.Hard chromeplated stainless steel 316 grade front ring.Silicone seal gasket.Clear toughened glass of 8mm thickness. Asymmetrical Lens. Luminaire hard wired with 3 x 0.5mm2 cable of 0.5 metre length. Supplied with mounting sleeve for preparing recessed opening in ground.Cable entries for through-wiring of mains supply cable. Integral constant current power supply. CRI (Ra) : ≥80. Dimension : ⌀116mm X 94mm (Without Installation Housing). Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Product supplied with factory sealed cable Moisture Arrestor and IP 67/68 Connectors. IP 67, IK 08,LED having 60,000 burning hours with minimum 70% lumen maintenance and power factor > 0.9 with THD less than 10% , SDCM≤3, Operating voltage range (150 - 270V AC).Mandatory CE Marking, BIS Certification, LM 79 report, IP, IK Report from NABL accredited Lab. Make: K-LiTE (Model No. 4098) or equivalent.

Supply and fixing of 28Watts GATE FIXTURE FITTING with cool day light suitable for wall / roof sheet mounting, made out CRCA powder coated body,IP65 aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and erection of 450mm Sweep Wall mounted type fan with fixing accessories

Supply and fixing of 450mm (18") sweep(Heavy Duty) AC exhaust fan complete with necessary wall opening and making good of the wall .

Supply and fixing of louvers shutters arrangements for 450mm (18") sweep AC exhaust fan

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and erection of 17.2mm, 3mtr long, Copper Bonded earth rod with backfill compound, including civil works, heavy duty Plastic Chamber cover withstand load of 60kN, etc., as per IS 3043 standards

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth

Supply of '2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS (5 Nos. per Set)

Supply of First Aid Box complete with all First Aid Medicines

Supply and fixing of Shock Treatment chart with Glass frame (in English & Local Language)

Supply and fixing of 4 Nos. Fire Buckets with river sand filling and necessary mounting frame made out of 40 x 40 x 6mm MS Angle with red painting

Supply and fixing of Metallic Danger Board as required by the Electrical Authorities (415Volts & 230Volts)

Supply and Installation for 1KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up and battery stand .

Supply and fixing of DP MCB sheet steel enclosure with 1 no 32A DP MCB switch with necessary fixing accessories

Supply and erection of 10Watts IP-65 rated Wall / Column mounted type Up-Down LED Light fitting with fixing accessories

Supply and erection of LED Strip light fitting with suitable driver and fixing accessories (5Watts / Meter)

Supply and installation of AIR-CONDITIONER WITH COPPER COIL,2.0 TR Split Type AC Unit - 5 Star Rated, 5 KVA capacity Automatic Voltage Stabilizer with time delay relay, 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit), Including MS stand for fixing outdoor unit.

SOLAR PV PLANT : 'Supply, erection, testing and commisioning of '20 kWp On Grid Solar PV Plant' comprising of: i) Solar panels of type Mono Crystline, PERC, etc. ii) Power Conditioning Unit (PCU)with MPPT, Inverter, Controls, Protection Devices, Interconnecting D.C. cables, Connectors, Junction Boxes and accessories. iii) D.C. D.B iv) A.C. D.B v) A.C. cables and accessories vi) Lightning arrestor, earthing, etc. vii) Module Metallic Mounting Structures viii) Installation, Testing and Commissioning corresponds to BIS and IEC requirements

Supply, installation, testing and commissioning of Long Range Wifi Device of following Specification: Networking Interface: (1) GbE RJ45 Port Power Method: PoE+, Pasive poE(48V) Max TX power: 2.4 GHz Antenna gain: 2.4 GHz Mounting: Wall or Ceiling Mounting Wifi Satndards : 802.11a/b/g Wireless security: WPA-PSK, WPA- Enterprises(WPA/WPA2/WPA3) VLAN: 802.1Q Concurrent Clients: 300+(As per Quotation)

Supply, installation, testing and commissioning of 12 Feet Long HVLS Fan with all the fixing accessories

Supply, installation, testing and commissioning of Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. a) 18 Persons - 4 Stops - (Shaft: 3mtr x 4mtr)

Supply, installation, testing and commissioning of Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. a) 13 Persons - 4 Stops - (Shaft: 1.8mtr x 2.45mtr)

Supply, installation, testing and commissioning of Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. a) 15 Persons - 3 Stops - (Shaft: 2.1mtr x 2.45mtr)

Supply, installation, testing and commissioning of Level-1, 3.3kW, 1Phase, 230Volts, EV Charging Stations for Two Wheelers (Individual Charging - Prepaid system)

Supply, installation, testing and commissioning of Level-2, 7.4kW, 1Phase, 230Volts, EV Charging Stations for Four Wheelers (Individual Charging - Prepaid System)

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 10TB Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony.

Supply of 4MP, Internet Protocol fixed DOME CAMERA (INDOOR & OUTDOOR)with following specification: a) 1/2.5" Progressive Scan CMOS, b) 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) c) Face Detection d) 120dB WDR, e) BLC/3D DNR/ROI, IP67 compliedf f) On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, g) Shutter Speed 1/3 s to 1/100,000 s, h) 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, i) rotate: 0° to 360°, 2.8 mm, j) horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, k) Lens Mount M12 & IR Range I5: up to 50 m, l) Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, m) Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W n) Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. with Camera Stand. (Make: Dahua/Panasonic)

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse with suitable Stand. (Rate as per quotation)

Supply, installation, testing and commissioning of 4K, 10x Optical, 5MP, Professional PTZ VC Camera:- Built-In Microphone Array and Speaker Tracking.

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Resolution: Ultra HD (4K) 3840 x 2160 b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -2nos n) Built in LAN o) Magic remote (Make: Sony/ LG /Samsung). (Rate as per quotation)

Supply and Clamping of CAT 6 unarmoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Supply and laying of armoured, Multimode, Thermoplastic Tape Inner Sheathed, PVC type sheathed 6 core Optical Fibre Cable with unique fiber excess length control method provides the cable with excellent mechanical and environmental properties and Cable - 2 Embedded FRP provides tensile strength & Anti-buckling properties. It is processed with Filling jelly - Thixotropic jelly to prevent Water ingress in loose tube.

Supply and fixing of Media convertor for optical fiber cable single mode with all the accessories

Supply and fixing of POE 8port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and Fixing of Rack with Accessories -Higher end 6U Rack with fan extra for the above rack. (speaker/data/cctv)

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply, Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up and battery stand .

Supply and fixing of outdoor 4X6 PVC box with 102mmX77mmX102mm with all fixing accessories.

Supply and Erection of 6mtr Length pole with base plate of size 300x300x12mm as per IS-875 with following specification. Pole Outter dia -76.10mm x 3.65mm Thick x 6 meter with foundation Charges.The Pole Should be hot dip Galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Supply, Installation,Testing & commisioning of 480 watts P.A Booster Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent)

Supply and Fixing of Rack with Accessories -Higher end 6U Rack with fan extra for the above rack. (speaker/data/cctv)

Supply, run, testing and commissioning of 2Core x 1.5sq sqmm PVC insulated Armoured Speaker Cable in suitable 25mm dia Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply, installation, testing and commissioning of IPIS (Integrated Passenger Information System) with necessary Controls, Display units, Cabling, wiring, control switches, etc.,

Supply and Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply, Fixing and Termination of RJ 11 Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply & Installation of CAT 6 PVC Module Box I/o socket & face plate single socket Erection and arrangement chargers (Higher end)

Supply and fixing of LAN Network Switches Un-Managed 10/100/1000 - 24 Port and 24 Port Patch Panel- Unloaded erection and arrangement chargers.

Supply, runing, testing and commissioning of 2 Pair Unarmoured 0.5mm Telephone cable in suitable Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply and Fixing of Rack with Accessories -Higher end 36U Rack with fan extra for the above rack. (Server)

Supply and fixing of Hand held Fire Extinguisher - CO2 - 4.5 Kg with suitable Metal Floor stand MS fabricated painted in black colour

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of EMERGENCY/FIRE EXIT (450mmx150mm double side)

Supply and fixing of FIRE EXTINGUISHER (100mmx150mm single side)

Supply and fixing of "EXIT " (400mmx150mm double side)

Supply and fixing of "MANUAL CALL POINT" (100mmx150mm single side)

Supply and fixing of "EVACUATION PLAN with AUTO GLOW" in A2

FIRE DETECTION & ALARM SYSTEM Supply, Installation, Testing & Commissioning of Addressable Fire Alarm Control Panel consists of display board which will have 160 Character Display with Touch key pad, Mother board 32 Bit Processor, In-built RS-485 Networking Circuit for peer to peer networking, In-built USB 2.0 Port, Loop Card having 254 devices of both detectors and modules in a single line circuit, SLC supports both Class A and Class B wiring Approval: UL Listed a) Single Loop Panel

Supply, Installation, Testing & Commissioning of Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility a) Multi Sensor - Heat Cum Smoke detector

Supply, Installation, Testing & Commissioning of Addressable Heat detector

Supply, Installation, Testing & Commissioning of Addressable Addressable Manual Call Point - Resettable type - with back box with Binary coded address setting with Status LED for 360° visibility.

Supply, Installation, Testing & Commissioning of Conventional type Horn / Strobe wall mounted type rated at 90 dBA @ 1m for Audible annunciation and 15cd minimum flashing at 1 Hz for visual indication.

Supply, Installation, Testing & Commissioning of Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications

Supply, Installation, Testing & Commissioning of Response indicator for all detectors located above false ceiling.

Supply, Installation, Testing & Commissioning of POWER SUPPLY : 24VDC Power Supply with 5 amp rating, having LED indications for Power supply ON,battery Fail,Battery Charging,battery back up etc.

Supply, Installation, Testing & Commissioning of 2 core x 1.5 sq.mm Red colour twisted pair shielded multi strand ATC armoured FRLS cable

FIRE PROTECTION SYSTEM SPRINKLER & HYDRANT SYSTEM Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm nominal dia ( EXTENAL + INTERNAL RAISER piping)

100mm nominal dia

80mm dia

65mm dia.

50mm dia. (SPRINKLER + DRAIN RAISER)

40mm dia.

32mm dia.

25mm dia.

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anticorrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 150mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 100mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 50mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 80mm Dia.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX /KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Supply and installation of RCC HUME Pipe of 300mm dia, NP2 class with collars for road / below floor crossing of fire pipe. The rate shall include excavation, soil leveling for bed and ends shall be closed with brick masonry, work as directed by site Engineer.

Supplying, fabricating, structural steel supports such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting for pipe support.

Construction of Concrete Pedestal supports including M.S. Supports - 900 x 300 x 300 mm ( For supporting above Ground for Fire pipes )

Supply, Installation, Testing & Commissioning of Flow Switches with two NO and two NC contacts with necessary nipple & other fittings a) 150NB

Supply, Installation, Testing & Commissioning of Flow Switches with two NO and two NC contacts with necessary nipple & other fittings a) 100NB

Supply ,Installation, Testing & Commissioning of standard response Glass bulb sprinkler Pendent rated 68 Deg. C.K-80

Supply, Installation, Testing & Commissioning of Dial type pressure guageIndustrial type) with necessary nipple & other fittings a) 150NB

Supply, Installation, Testing & Commissioning of Dial type pressure guageIndustrial type) with necessary nipple & other fittings a) 100NB

Installation, Testing & Commissioning of150mm dia sprinkler alarm gong valve with necessary fittingsWith Complete SetUp As Per Specification

Supply, Installation, Testing & Commissioning of 25mm Ball valve with necessary nipple & other fittings

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition. e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 185 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured copper cable

10 core 2.5 sq.mm. armoured copper cable

2 core 2.5 sq.mm. armoured copper cable

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers

Supply and laying of 25mm X 6mm GI strip

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories for laying the refrigerant line

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - a) 200mm Nominal dia

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - 150mm Nominal dia

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - 100mm Nominal dia

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - 80mm Nominal dia

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - 50mm Nominal dia

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - 25mm Nominal dia

Exhuast pipe for Diesel engine of with mineral wool insulation with aluminum sheet.- M.S. 'B' class pipe - 150 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. - 150mm Dia.

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. - 100mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. - 80mm dia

Supplying, fabricating, structural steel supports such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting for pipe support.

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. - a) 200mm Dia.

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. - 150 mm nominal dia

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. - 100 mm nominal dia

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. - 80mm nominal dia

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. - 50 mm nominal dia

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. - 25mm Dia.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. - 15mm Dia.

Supplying, installing, testing and commissioning of C. I. Flanged FOOT valve with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete. (PN 20) a) 200mm NB

Supplying, installing, testing and commissioning of C. I. Flanged FOOT valve with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete. (PN 20) a) 100mm NB

Supply, Installation, Testing & Commissioning of Flow meter (150mm) size with required flanges, nuts, bolts etc. complete.

Providing, fixing, testing and commissioning of air vessel (size 450 mm dia and 1500mm HOS) fabricated from 10 mm thick shell & dished end 12 mm thick M.S. Plate for pressurization of hydrant/ sprinkler/water curtain system complete. 50 dia. socket for drain, 65 dia. socket for inlet, 25 dia. sockets for pressure relief valve, pressure switches and pressure gauges, 450 mm dia manholes, M.S legs, epoxy painted from inside and enamel paint from outside after grit blasting complete.

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supply, Erection, Testing and Commissioning of Metallic-Rubber bellow flexible connections of suitable pressure rating to be installed at equipments suction and discharge.with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. - a) 200mm NB

Supply, Erection, Testing and Commissioning of Metallic-Rubber bellow flexible connections of suitable pressure rating to be installed at equipments suction and discharge.with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. - 150 NB

Supply, Erection, Testing and Commissioning of Metallic-Rubber bellow flexible connections of suitable pressure rating to be installed at equipments suction and discharge.with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. - 100 NB

Supply, Erection, Testing and Commissioning of Metallic-Rubber bellow flexible connections of suitable pressure rating to be installed at equipments suction and discharge.with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. - 80 NB

Supply, Installation, Testing & Commissioning of Puddle Flange - a) 200mm Dia.

Supply, Installation, Testing & Commissioning of Puddle Flange - a) 150mm Dia.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: KIARTAR / OMEX / EQUIVALENT)

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. A) 25mm dia.

Supplying, installing, testing and commissioning of `Y' - Type Strainer with Flanged ends - 100mm Dia.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Supply and fixing of Puddle Flange suitable for 150mm dia at Terrace tank with unions etc., complete.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 150mm dia.

Supply and Erection 50 inches 4K Ultra HD Smart LED Google TV with the following specifications. Colour: Black TV Display: Refresh Rate:60 Hz Screen Resolution: 3840 x 2160 - Ultra HD Screen Size (Diagonal): 126 cm - 50 inch HDMI & USB Ports No of HDMI Ports: 3 No. of USB Ports: 2 USB: Yes TV Audio Related Rated Speaker Output Power (RMS):20 Watt TV Connectivity Choices Additional Connectivity Apple Airplay, Apple Homekit, Alexa Gesture Control: Yes TV Placement Wall Mounted Depth (without stand): 7.7 cm Height (without stand): 66.2 cm Width (Without Stand): 112.7 cm Power Details Power Consumption: 115 Watt Power Supply: 240 V Additional Features Open Baffle Speaker, Full Range (Bass Reflex ) x 2 , Dolby Audio, Clear Phase Google TV, Watchlist, Ok Google, Google Play, Chromecast, Built In Mic Variable Refresh Rate and ALLM (Auto Low Latency Mode) Live Colour, Motion Flow. Brand :SONY or Equivalent

KSR ASSOCIATES (BID ID -1278424)

SRI NAACHIMAAR ENGINEERING CONSTRUCTIONS (BID ID -1278267)