SPECIAL REPAIRS TO BLDG NOS P-76 (SINGLE OFFRS ACCN BLOCK OF SIX), P-86 (OFFRS MESS MAIN BLDG) AND P-87 (OFFRS MESS KITCHEN) OF EME BN UNDER GE (SOUTH) BATHINDA AT BATHINDA MIL STATION

Amount

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc. and removing the debris to a distance all as specified and directed by Eng-in-Charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and pre cast concrete articles.

Demolition of PCC in ground floors and pavings including tiles of any description etc. not exc 15cm thickness (below or above ground level) and removing the debris to a distance all as specified and directed by Eng-in-Charge.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and re-fixing in the same opening including easing and adjusting including renewal of unserviceable screws etc complete.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4).

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6).

All as per item No 10 above but except bricks (Old serviceable bricks obtained from demolition shall be used).

M & L for non skid coloured ceramic tiles of size minimum 400mm x 400mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) complete all as specified. Note: Only course sand shall be used in screed bed.

M & L for vetified tiles of size 1000mm x 1000mm x 10 to 12 mm thick, ultra charged, polished, dark shade, area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6). Note: Only course sand shall be used in screed bed.

M & L for vetified tiles, of size 600mm x 600mm x 9 to 10 mm thick, ultra charged, polished, light shade, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6). Note: Only course sand shall be used in screed bed.

All as per item No 14 above but on vertical surfaces as in skirting/dado etc including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile.

S&F glazed ceramic coloured / printed tiles 450 x 350mm / 450 mm x 300 mm, 7 to 8mm thick in vertical surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile.

M&L for marble work (Makrana white) 18 to 20 mm thick (table rubbed and polished) in flooring, wall lining (veneering to wall) and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble including M&L for 15 mm thick Screed bed or bedding layer in CM (1:6).

M&L for granite (of any type) work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, dado/skirting and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including M&L for 15 mm thick Screed bed or bedding layer in CM (1:4).

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish) complete all as directed

Drilling holes of suitable size for passing tubes of any description into or through RCC cooking platform slab with stone or brick wall etc and the like of thickness not more than 250 mm by electric drilling machine and making good complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 125 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

All as per item No. 21 above but frame size 105 x 60 mm

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate in filling in chowkats/ door frame or bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

S & F 35mm thick factory made paneled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S&F aluminium alloy powder coated glazed and wire gauged door including shutter fixed to sliding type /openable frame and channel as directed and as per IS specifications including 5.5 mm thick tinted/itched/plain glass / SS wire cloth as required, handles, tower bolt, floor spring heavy duty, locking arrangement Godrej make rubber gasket and door stopper complete. (minimum thickness of power coating shall be 50 micron) with following sections of Jindal or equivalent make of Hindalco or Indal. (a) Door frame single groove - Section No. 20078 of size 101.6 x 44.45 x 2.01 mm weighing not less than 1.605 Kg per mtr. (b) Door shutter top- Section No. 19505 of size 95.25 x 25.4 x 2mm weighing not less than 1.51 Kg per mtr (c) Door shutter bottom - Section No. 19517 of size 150 x 25.4 x 3.1mm weighing not less than 2.376 Kg per mtr (d) Door shutter vertical - Section No. 19550 of size 85 x 44.45x 1.56mm weighing not less than 1.139 Kg per mtr (e) Door shutter middle - Section No. 19564 of size 100 x 44.45 x 2mm weighing not less than 1.603 Kg per mtr (f) Glazing clips - Section No. 19352 weighing not less than 0.097 Kg per mtr

S&F aluminium alloy powder coated window sliding type (three track) with two glass shutter and one stainless steel mesh shutter including 5.5 mm thick tinted / transparent glass of polycarbonate including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, 0.56 mm dia SS wire mesh, all fittings complete. (minimum thickness of power coating shall be 50 micron) with following sections of Jindal or equivalent make of Hindalco or Indal. (a) Window frame bottom - Section No. 20677 of size 116 x 36.5 x 1.80mm weighing not less than 1.674 Kg per mtr. (b) Window frame top and side- Section No. 20678 of size 116 x 25 x 1.6mm weighing not less than 1.194 Kg per mtr (c) Window shutter top and bottom - Section No. 20506 of size 43 x 25 x 1.70 mm weighing not less than 0.717 Kg per mtr (d) Window shutter side - Section No. 20507 of size 43 x 25 x 1.70 mm weighing not less than 0.642 Kg per mtr (e) Window shutter interlock - Section No. 20508 of size 43 x 25 x 1.70 mm weighing not less than 0.802 Kg per mtr (f) Glazing clips - Section No. 19352 weighing not less than 0.097 Kg per mtr

S&F factory made powder coated aluminium window and ventilator shutters, side hung type without sash bars with including glass 4 mm thick and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21, 100mm long (2 nos.) suitable handle (1 no.) complete all as specified. (minimum thickness of power coating shall be 50 micron) with following sections of Jindal or equivalent make of Hindalco or Indal. (a) Outer frame - Section No. 21034 of size 104 x 45.60 x 2.64 mm weighing not less than 1.555 Kg per mtr. (b) Mullion - Section No. 20941 of size 59 x 33 x 2.10 mm weighing not less than 0.851 Kg per mtr (c) Shutter with glass - Section No. 20509 of size 38.5x33 x 3 mm weighing not less than 0.663 Kg per mtr (d) Glazing clips - Section No. 19352 weighing not less than 0.097 Kg per mtr

S & F MS framed work such as grills, gratings, guard bars etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Gde E-165.

M & L for second class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads of sectional area exceeding 6 Sqcm and not exceeding 13 Sqcm.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

All as per item No 31 above but fixed in repairs.

Supply only butt hinges, medium weight, cold rolled mild steel and fixed, size of hinges 100mm.

Welding in repairs exc. 2.5cm but n.exc 5 cm in length for thickness of metal to welded n.exc 6mm.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised of 30 mm width of flap (when open).

S & F 200 mm long aluminium anodised, barrel tower bolts of extruded section.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type), and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, length of bolt 250mm.

S & F 125 mm aluminium handles, cast type, anodised.

S & F in repairs 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete

S&F 100 mm size Hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws

S&F magnetic catcher as in cupboards etc to catch and support of best quality

S & F floor door stopper of aluminium alloy body, and tongue, ISI marked, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips size not exceeding 1.5 Sqm each pane complete.

S & F sheet glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary complete.

S&F stainless steel CP pipe 25 mm dia, wall thickness not less than 20 gauge as curtain rod fixed with and including fancy type brackets and decorated end knobs (finials), stop roller etc fixed on wall for doors and windows curtains, cuttig as per required length and fixed at site including fixing arrangements, rawl plugs, screws etc including taking down any type of curtain rod / pelmet boxes complete.

S&F in repairs PVC waste pipe with socket suitable for connection to waste fittings of 32/40 mm dia and of minimum length 750 mm.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Refixing of old 15 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)

Refixing of old 20 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)

M & L for 15 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors.

M & L for 20 mm bore GI pipe, medium grade, ISI marked, with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F gun metal, globe or gate valves, heavy duty, with iron wheel head, screwed both ends for iron pipe of 15 mm bore dia.

S&F gun metal, globe or gate valves, heavy duty, with iron wheel head, screwed both ends for iron pipe of 20 mm bore dia.

M&L for 75mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1.

S&F swivel shower of chromium plated of size 125 mm dia for fixing with 15 mm bore dia of pipe as per Cat Part No OHS-1789 of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F stop valves, chromium plated, angular type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe as per Cat Part No ORP-10057PM of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S & F PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts.

S&F towel rack 600 mm long with lower hanger all as per cat Part No AKP 35781PS of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F in repairs vitreous china wash down water closet pan (EWC) (single piece), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc with interal flushing cistern and white coloured plastic seat cover and mild steel chromium plated or aluminised hinging device all as per cat Part No LYS-WHT-0204 / CAN-1111NM of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F in repairs vitreous china pedestal type wash basin, white, flat back complete all as per Cera Cat part No. S0240113 for wash basin and S2090106 for pedestal or equivalent model of approved make from list of make attached here-in-after excluding waste, chain and plug and porcelain stopper but including waste coupling and PVC waste pipe of 32 mm dia and fixed on existing brackets complete .

S&F in repairs shower mixer with provision of connection to exposed shower pipe and hand shower with connecting legs and wall flange complete all as per cat part no LYR-38145 & SHA 1213 OF Jaquar or equivalent model of approved make from list of make attached here-in-after.

S & F in repairs PVC valve less, syphonic action type, flushing cistern, 10 litres capacity, low level, dual syphon and button system, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia upto 1250 mm long all as per Cat Part No FLS-WHT-5201C of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after complete.

S&F in repairs vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F in repairs health faucet brass body with wall hook and 1 m SS pipe all as per cat part No F8030301 of Cera or equivalent Cat Part of make approved in Appendix attached here-in-after complete.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete.

S&F in repairs stainless steel plate rack of made out of 1.00 mm thick sheet with chromium plated screws, rawl plugs of size 90 cm x 60 cmx 25 cm complete all as specified.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 600 mm long between flanges fixed with CP screws and wooden cleats as per Cat Part No AKP- 35711 PS of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 120 mm wide with CP brackets, guard and railing 600 mm long as per Cat Part No CAN - 1171N of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F in repairs brass chromium plated soap dish fixed to wall with brass screws as per Cat Part No AQN-7731 of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S & F PTMT Mirror cabinet of size 350 x 450mm best quality confirming to samples kept in GE's office, complete all as specified and direct.

S&F in repairs 15 mm bore chromium plated, fancy type, bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe, or for brass ferrule as per Cat Part No LYR-38037 of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F in repairs stop valves, chromium plated, concealed type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe as per Cat Part No ALD - 083CQT of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

S&F 500 ltr capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

All as per item No 76 above but capacity of tank 1000 litres.

S&F in repairs 125 mm size CP grating of best quality.

S & F in repairs, fancy type corner glass shelf (300mm) with CP brass bracket and SS/ CP brass railing etc complete all as per Cera Cat part No. F5005103 or equivalent model of approved make from list of make attached in tender documents.

S & F in repairs, fancy type stainless steel recessed type toilet paper holder complete all as specified and direct. Make:- Jaquar Cat part No. AQN-7753 or equivalent model of approved make from list of make attached in tender documents.

S&F in repairs, chromium plated towel ring complete. Make:- Jaquar Cat part No. AQN-7721 or equivalent model of approved make from list of make attached here-in-after.

S & F in repairs, peg set/ coat hooks (set of 4/ 5), stainless steel complete all as specified and direct.

S&F in repairs chromium plated central hole basin mixer for mixing hot and cold water, fancy type, for 15 mm bore pipe as per Cat Part No VGP-81051B of Jaquar or equivalent Cat Part of make approved in Appendix attached here-in-after.

M & L for 25 mm thick PCC (1:2:4) type B0 using 20mm graded stone aggregate as in sub base, floor, path, pavings etc. and finishing the surface as even and fair or even and rough to receive top layer complete.

M&L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement mixed with liquid water proofing material as per manufacturer's instruction complete all as specified. (Liquid water proofing material shall be measured and paid for separately.)

M&L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling complete all as specified.

M&L for sunken treatment to sunken floor with polymer modified mortar using DR fixit pidicrete or equivalent model of approved make from list of makes attached in tender documents, making of angle fillets all around the perifery of the wall with polymer modified mortar using DR fixit pidiproof LW+ @220 ml per bag of cement. Sealing sanitary pipe inserts, electrical fit outs etc provided in the floor and walls with bath seal traps, grouting the gaps around pipe inserts with bath seal grout or DR fixit micro concrete. Applying two coats of DR fixit bath seal WPC in the sunken areas and extending it upto 150mm above the finished floor level which include laying of a 150mm wide strip of an open wooven glass fibre mesh over the angle fillet on the first coat while it still wet laying a protective 10mm thick in cement mortar (1:3) plaster admixed with DR Fixit Pidiproof LW @ 220 ml per bag of cement complete all as per manufacturers instruction. (Make: Dr Fixit/ Fosroc/ BASF/ STP) NOTE :- (i) Complete treatment shall be carried out by authorized applicators of water proofing manufacturers . (ii) WP Materials shall be measured and paid for separately.

Supply only liquid water proofing material, ISI marked.

M&L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling of sunken floor including demolition of existing PCC.

Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.

M&L for wire brushing and cleaning top surfaces of roof slabs etc, including washing the roof surface with water and making the surface free from mud etc complete all as specified.

M&L for 15 mm thick screed bed or bedding layer in cement mortar (1:3) on roof surfaces parapet or vertical beam surface (horizontal or vertical) finishing the surfaces even and fair complete all as specified. (Note :- Course sand (Toka sand) shall only be used in screed bed/plastering.)

M&L for water proofing treatment over RCC slab by applying oil bound bituminous primer @ 0.30 kg/Sqm and providing and laying 3 mm thick APP modified water proofing memberane weighing not less than 3.50 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having soften point not less than 150°C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing strength of 180 N, torch application, side overlap 75 mm and end overlap 100 mm including ponding test all as specified and directed.

M&L for Lime concrete in lime mortar ratio (1:3) using 40 mm graded brick aggregate, laid to slope as directed by Engineer in charge over RCC roofs as padding complete alll as specified. Note: Minimum thickness of lime concrete at lower end shall not be less than 50mm.

M&L for 20- 22 mm thick factory made PCC tiles of size 250mm x 250mm with grey cement and no pigment , bedded in cement mortar (1:4) 15 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement complete all as specified.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing material as in benching, kerbs, mud stops, along side walls adjoining to roofs and similar items complete. (Water proofing material shall be measured and paid for separately).

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar (1:3).

S&F PVC (SWR) 110mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, fixed to walls with and including 40 mm x 3mm GI flat clamp including taking down old pipes and fittings.

Fixing only in repairs PVC rain water pipe of any description, jointing pipe with elbow/pipe joint with chemical cement/suitable adhesive and providing MS clamps all as directed.

S&F PVC (SWR) 110mm bore bends / shoes of any radius.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement.

M & L for RCC (1:2:4) type B1 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies, lintels, fins, facia, and the like, finished exposed surface fair and even. (Reinforcement and form work shall be measured and paid separately)

M & L for TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, canopies, lintels, fins, facia and similar work; not exceeding 200mm thick (horizontal or sloping) for flat rough surfaces of concrete.

Dismantling of 100mm internal dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required.

All as per item No 107 above but dia of pipe 75 mm.

S & F 75 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps / laid in trenches

S & F 100 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps / laid in trenches.

Fixing only in repairs 75mm / 100 mm bore CI pipe with lead joints as in trenches / floors or fixed to wall with and including suitable size clamps.

S&F in repairs oval access door cover to CI pipes of 75 mm bore with rubber washer packing and bolts and nuts as required complete.

S&F in repairs oval access door cover to CI pipes of 100 mm bore with rubber washer packing and bolts and nuts as required complete.

S & F 75mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured).

S & F 100mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured).

S & F 100mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches.

Fixing only in repairs 75mm / 100 mm bore CI fittings.

M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate in copings, roof kerbs, surface channels, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

M&L for providing cement concrete (RCC/ PCC) 1:2:4, type B-0 (using 12.5mm graded aggregate) as in broken or cracked chajjas, RCC column, beams, stairs/ steps etc in one or two layers as required (thickness from 25mm to 50mm) and finishing the surface with 15mm thick cement plaster in cement mortar (1:4) including taking out loose/ cracked concrete portion and plaster etc and applying neat cement slurry before concrete work, complete all as specified. Note : 1. Rates deemed to include for any scaffolding/ ladders, form work etc or any other mean to work in two story buildings including welding of reinforcement to be provided for repairs of chajjas, beams, columns, staircase, fins and facia etc. 2. The reinforcement shall be measured and paid separately.

M & L for machine cut kota stone slab flooring minimum size 450 mm x 450 mm, 18 to 20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 15 mm thick Screed bed or bedding layer in CM (1:6).

All as per item No 120 above but in vertical surfaces such as steps , riser , skirting, dado and pillars as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4).

S & F in repairs vitreous china wash hand basin, white, of size 550mm x 400mm , excluding waste, chain and plug and porcelain stopper but including 32 mm dia waste coupling fancy type chromium plated, and PVC waste pipe of 32 mm dia and fixed all as directed complete .

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exceeding 10cm girth in brick walls.

M & L for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4).

Cutting openings, through brick wall built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc or cutting out defective brick work for under-pinning including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard core, etc, to store and rubbish not exceeding 50m.

Forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar (1:6), complete

S & F 75mm dia cast iron cowls.

S & F 100mm dia cast iron cowls.

M & L for preparing previously treated surfaces of walls and applying two coats of white wash all as specified.

S&F decorative laminate type I, of surface finish, colour and pattern as approved, 0.9 mm thick, fixed with approved adhesive as per maker's instructions.

S&F decorative laminate type I, of surface finish, white colour and pattern as approved, 0.75 mm thick, fixed with approved adhesive as per maker's instructions.

Dismantling boarding of any type and description fixed in any position with rails including fillets complete.

M & L for plywood, 18/19 mm thick, BWR grade, type BB, ISI marked, fixed with screws to timber frame work as in cupboard shutter.

M & L for plywood, 6 mm thick, BWR grade, type BB, ISI marked, fixed with screws on walls.

S&F in repairs solid factory made PVC wall lining consisting of 5 mm thick wood grain PVC printed sheet inclusive of solvent cement and fixing at site on PVC frame all as per specifications and drawings in SSR Part -II including PVC strips or channels as required.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame all as per specifications and drawings in SSR Part -II (2010).

S & F in repairs Stainless steel telescopic channels 450 mm long for drawers of kitchen cup boards of any length complete all as specified.

S & F fancy type, 100 mm stainless steel handles, for cup boards shutter complete all as specified.

M&L for preparation of newly plastered or unplastered surface and applying three coats of white wash on ceilings.

M&L for preparation of newly plastered or unplastered surface and applying three coats of white wash on walls.

M & L for preparation of newly plastered surfaces of external walls and applying the following:- (i) Two coats of 100% acrylic exterior emulsion paint by using airless spray/ roller over and including a coat of external acylic primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engr- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparation of newly plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of 100% acrylic emulsion paint by using airless spray/ roller over and including a coat of acylic internal primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engr- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparing previously treated surfaces of walls and applying one coat of white wash all as specified.

M & L for preparing previously treated surfaces of walls, filling the depression with putty for making the surface smooth and applying two coats of acrylic paint by using airless spray/ roller.

Complete removal of existing treatment on wall (any number of layears) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered external surfaces of walls and applying the following:- (i) Applying wall care putty in two coats on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of weather proof (antifungal) exterior emulsion paint by using airless spray/ roller over and including a coat of exterior emulsion primer.Make:- Apex Brand of Asian Paints/Excel Brand of Nerolac Paints/Berger Weather Coat Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for painting to old or previously treated wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint including preparation of surfaces.

M & L for painting to old or previously treated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint including preparation of surfaces.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint including preparation of surfaces.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M&L for rubber gasket 50 mm wide, fixed with screws or nails at bottom of door shutters of any description.

M & L for PCC (1:5:10) type E2 using 40mm graded stone aggregate in foundations, filling and mass concrete.

Preparing surfaces of wood and wood based materials, new or old, of any description or girth, not otherwise described and treated with two coats of creosote.

S & F MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc shall be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as directed conforming to Fe 290 Gde E-165.

S&F in repairs mild steel, plain, black sheet 1 mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required.

Complete removal of existing treatment on wall (any number of layears) by scrapping with steel wire brushes or any other means and M&L for preparation of internal surfaces of walls and applying one coat of granular texture over a coat of primer complete.

M&L for aluminium powder coated (minimum thickness of powder coating 50 micron) frame for partitions, doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F cost iron body door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg all as specified.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified.

M&L cement concrete type C-2, (1:3:6) 40 mm graded stone aggregate as in sub base of floors, paths & paving etc complete all as specified.

M&L for 60 mm thick machine pressed precast concrete inter-locking tiles (M-35) any shape, size, colour/ patten ( as approved) over and including 25 mm thick sand bed/ cushioning complete all as specified.

M&L for cement concrete type B-1, 1:2:4 mix (20 mm graded crushed stone aggregate) as in bedding, benching of man holes, copings , roof kerbs & surface channel etc complete all as specified.

Removing excavated earth at a level n.exc 1.5m above the starting point to a distance exc 50 mtr all as specified.

M&L for first quality, scratch free, straight cut/ joint free, 9-10 mm thick vitrified pavers of size 300 mm x 300 mm for external use in floors & incl 15 mm thick in CM 1:6 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of sab complete all as specified.

M&L for cement concrete chequered tiles with grey cement and pigments 30cm x 30cm x 25 mm thick, jointed and pointed in neat cement slurry pigmented to match colour of tiles over & including 15 mm thick, screed I n cement mortar 1:6 as in floors & path etc complete all as specified.

M&L for treatment at points of contact of wood work by 20 EC chemical emulsion (in oil or kerosene based solution) @ 0.5 ltr/ hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same with CM 1:4 complete all as specified.

S&F aluminium glazed and wire gauged door with frame for double shutter 2 Nos shutter ( one for gauged and other for glazed ) extruded aluminium anodised natural shade/ powder coated satin finish sections with closing arrangements, handle for openable shutter complete with 5.5 thick plain/ tinted/ itched glass/ stainless steel wire cloth, packing with rubber gasket, aluminium beading etc around both sides for fixing of glass as required all as specified and directed. (minimum thickness of power coating shall be 50 micron) with following sections of Jindal or equivalent make of Hindalco or Indal. (a) Door frame retungal tube - Section No. 14078 of size 127 x 38.10 x 1.74 mm weighing not less than 1.518 Kg per mtr. (b) Door shutter top (02 Nos glazed and wire gauged)- Section No. 19505 of size 95.25 x 25.40 x 2.00 mm weighing not less than 1.51 Kg per mtr (c) Door Shutter bottom (02 Nos glazed and wire gauged)- Section No. 19517 of size 150 x 25.40 x2.20 mm weighing not less than 2.376 Kg per mtr (d) Door Shutter vertical (02 Nos glazed and wire gauged)- Section No. 19550 of size 85 x 44.45 x1.56 mm weighing not less than 1.139 Kg per mtr (e) Glazing clips - Section No. 19352 weighing not less than 0.097 Kg per mtr

Internal Electrification

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

Dismantling & Taking down carefully existing electric/ electronic meters, depositing the same meters safely to E/M store yard & refixing the same after completion of repair work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium duty ISI marked) and conduit fittings with and including replacement of mild steel/ pressed steel sunken box with modular type sunken boxes suitable for modular switches with modular frame and white cover plate and brass screws for one fan/light controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 170 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 170 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 170 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continues as earth wire connected to earth dolly, conductor etc.

All as per item No 170 above but for call bell/buzzer point.

All as per item No 170 above but for one light point controlled by two switches two way.

S & F Switch modular, single module, one way, 5/6 Amp .

S & F Switch modular, single module, two way, 5/6 Amp .

S & F Switch modular, single module, one way, 15/ 16 Amp .

S&F 6 Amps bell push modular switch, single module, 230 volts AC, ISI marked complete all as specified and directed.

S & F Modular type socket, multipurpose, 2 in 1, 5 Pin, 6 Amp, two module etc. (Note: Switch and socket shall be of same make.)

S & F Modular type socket outlet universal, multipurpose, 2 in 1, 3 Pin 6 Amp and 6 pin 16 Amp, two module etc. (Note: Switch and socket shall be of same make.)

S&F, Modular type fan regulator electronic step type (1-5), two module, 230-240 Volt, AC supply, complete all as specified and directed.

S&F electric / electronic bell, ding dong type, 230 Volt, AC supply complete all as specified.

S&F ceiling rose, 3 plate, surface bakelite type, Polycarbonate body, 6 Amps, 250 Volts AC, 20x50 mm, three terminal (ISI marked) complete all as specified.

S & F, In repair, Lamp holder of PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb.

S & F 18/20 watt Retro LED tube light fitting, wall/surface mounted, IP 20 protection, conforming to IS 16106/IS 16107, minimum 6000K batten decorative type 4 feet long polycarbonate body, white, inbuilt LED driver, power factor>0.95 , Make all as per Crompton Cat Part No. DMLN1LT8-16 (for batten) and Cat part No. LT8-20-865-2 (for tube light) including 18/20 watt tube rod or equivalent model of any make given in Appx 'B' connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting all as directed.

S & F LED mirror light fitting of 12/14 watt, 6000K, linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete including 12/14 watt tube rod all as model No LCL-14-CDL of Crompton with 14 watt rod or equivalent model of approved make from list of make attached in tender documents including connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting.

S & F surface mounted, decorative round plastic comprising of high brightness LED lamp 10/12 watt, 6000K polycarbonate including all other accessories and fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector. Make:-Crompton cat part No LCSR-12-CDL or equivalent model of approved make from list of make attached in tender documents including taking down old existing light fitting.

S & F wall mounted/surface mounted decorative wall light fixture in cylindrical profile made up of polycarbonate suitable for and including LED lamp of 7 watt B22 base complete fitting and all other fixing accessories including electric connection with flexible copper wire twin core including taking down old existing light fitting. Make:- Crompton Cat part No. DCWL 15 DF or equivalent model of approved make from list of make attached in tender documents Note:- The rate of LED lamp of 7 watt B22 base is deemed to be included in quoted rate and nothing extra shall be paid on this account.

S&F LED light fitting, recessed mounted 36( ±10%) watts of size not less than 595mm x 595 mm in complete with panel light and dirver etc long life LED EDGE LIT luminaire complete including taking down old existing light fitting of make Crompton Cat Part No. LDTLBK-36W- CDL or equivalent in Bajaj/ Havells/Philips complete all as specified and directed.

S & F energy efficient LED street light fitting of 25 Watt with PDC aluminium body and clear glass with lens for wide beam distribution, top maintainable type with IP 66 degree of protection, PF>0.95 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 5 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including 25 watt LED lamp with GI brackrt-01 No, MS clamp-02 Nos suitable for walls/ columns and making electrical connection with providing of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as per SYSKA cat part No. SSK-SLF-CF-25W-WL or equivalent model of any make given in Appx 'B', Cat Part No. as approved by GE complete all as specified including taking down old unserviceable existing street light fitting of any type and capacity from bldg along with accessories.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 6 sqmm, 1100 volts grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including accessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multi stranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishing the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 4 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including accessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 4 sqmm unsheathed multi stranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishing the surface to match with existing surface etc including taking down old unserviceable wiring 4 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 4 way, DB TPN 415 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection including taking down old unserviceable MCB complete all as specified.

S & F MCB, SPN, 40 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCB, TPN, 63 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCB TPN 100 Amps, 'C' curve, 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable isolator complete all as specified.

M & L in replacement of earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.

S & F in replacement ceiling fans energy efficient, 1200 mm sweep 230 V, energy efficient type white coloured with down rod, rubber reel, nut, bolts, washer clamps, canopys and connecting up using suitable size copper conductor flexible cable from existing ceiling rose to fan complete including depositing old fans in MES store yard.

S & F metal body Exhaust fan 300 mm sweep single phase 230V, 50 Hz, 1400 RPM complete with louvers, frame and accessories and connecting up using suitable size copper conductor flexible cable from existing ceiling rose to fan including making hole for proper fitting of exhaust fan, louvers and making good with existing finishing complete.

Supply, installation, testing and commissioning of water heater storage type (BEE 5 star rating), electrically operated, single phase, 230V, 50Hz of capacity 25 ltrs with vent pipe, fusible plug, thermostat, safety valve, proper earth connector, SS tank complete with all accessories required for plumbing work (Inlet and outlet GI pipe), grouting bolts and nut etc, inlet and outlet pipe connection (CP) including one NRV, one bib tap and one stop cock complete.

Taking down old serviceable / unserviceable ceiling fan 1200 / 1400 mm sweep, 230 volts, AC, single phase, dismantling the ceiling fan and taking out complete rewinding (if unserviceable) for replacement of super enameled copper winding wire of existing gauge and size including thoroughly cleaning all the components of fan, oiling and varnishing the fan with and including replacement of rusted bolts/nuts/split pin, rubber reel, flexible twin core cable of size 23/0/0.00076 approx one metre long for each fan, machine screws and painting the fan and writing MES No. on fan and re-fixing the fan all as directed.

PVC connection pipe wire braided 450 mm long with PTMT nuts, washers of both ends complete all as specified

Single pole and neutral enclosure 240 volts with two pin and earth plug and socket with one single pole MCB 20 Amp complete all as specified

S&F wall mounting fan 400 mm sweep suitable for single phase 230/240 volt with speed and swing adjustment fixed to walls with bolts/ screws complete all as specified and directed.

S&F heavy duty metal body exhaust fan 450 mm , sweep 900 RPM, 240 volt compete with louves and shutters and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated sheathed copper conductor flexible cable 24/02 mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cement mortar (1:4) white washing matching with existing colour etc complete all as specified.

Taking down old serviceable geyser of any size and painting the same with spray painting and writing MES No. including replacement of rusted bolts/nuts and flexible twin core cable of size 2.5 sqmm and re-fixing the same after completion of repair work to its original position all as directed. (Note: If any geyser, ceiling fan, exhaust fan, electric meter is found at site before starting the work, the contractor shall hand over these items to store yard of AGE E/M in writing to avoid any complication and refixing of electric meter is the sole responsibility of the contractor before handing over the site to user.)

M/s Verma Construction Company

M/s MITTAL CONSTRUCTIONS

SHARDA ENTERPRIES

M/s Kamal Builders

M/s Nuway Constructors India Pvt. Ltd.