Construction of Auditorium Cum NDA Motivational Hall at Sainik School, Nalanda

BIHAR STATE EDUCATIONAL INFRASTRUCTURE DEVELOPMENT CORPORATION LTD. SHIKSHA BHAWAN, SAIDPUR, PATNA

BILL of Quantity for Construction of Auditorium Cum NDA Motivational Hall at Sainik School, Nalanda

Rates are based on BCD SOR 2022 (w.e.f. 01.01.2022) for Civil & BCD SOR 2023 (w.e.f. 01.09.2023) for Electrical Works

Amount of B.O.Q. of Schedule Item (In Rs.) :- 8,52,25,536/- Amount of E.M.D. (In Rs.) :- 22,52,300/-

Cost of B.O.Q. (In Rs.) :- Rs.10,000/-(Ten Thousand) Completion Period :- 15 Months

Part A (Items on Schedule Rate, for which tenderer have to quote rates on % above/below basis)

Sl. No. Item No. Item of Work QTY unit Rate Amount

1 BSR 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. All Kinds of soil 4009.323 cum 314.90 1,262,535.81

2 BSR 2.26 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead 2329.581 cum 123.90 288,635.09

3 BSR 2.25A Excavating, supplyingand fillingof local earth (including royaltybut excludingcairriagecost) bymechanical transport uptoa leadof 3km also including ramming and watering of the earth in layers not exceeding20cmintrenches,plinth,sidesof foundationetc.complete. If localearthisavailableatmorethan3kmleadtheactual leadmust beapprovedbycompitentauthority. cairraiageofmaterialwillbepaid seperately and calculated after deducting initial lead 3221.072 cum 411.70 1,326,115.34

4 BSR 16.78.1 Construction of granular sub-base by providing close graded Material conforming tospecifications,mixing inamechanicalmix plantatOMC,carriageofmixedmaterialbytipperstoworksite, for all leads&lifts, spreading inuniformlayersof specified thickness with motor grader on prepared surface and compacting with vibratorypower roller toachieve thedesireddensity, completeas per specifications and directions of Engineer-in-Charge. 133.000 M3 1,310.40 174,283.20

5 BSR 16.69 Providing and laying at or near ground level factory made ker bstone of M-25 grad ecementconcreteinpositiontotherequiredline, level andcurvature, jointedwithcementmortar1:3(1cement: 3coarse sand), includingmaking jointswithorwithoutgrooves(thicknessof jointsexceptatsharpcurveshallnot tomorethan5mm), including makingdrainageopeningwherever requiredcompleteetc. asper directionofEngineer-in-charge(lengthof finishedkerbedgingshall bemeasured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 42.000 M3 7,998.80 335,949.60

6 BSR 16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 1330.000 M2 778.00 1,034,740.00

7 BSR 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 225.053 cum 287.30 64,657.73

8 BSR 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of E/l, 2234.807 sqm 283.30 633,120.82

9 13.18 15mmcementplaster1:3(1cement:3coarsesand) finishedwitha floatingcoatofneatcementontheroughsideofsingleorhalfbrick wall. 64.800 SQM 229.30 14,858.64

10 BSR 4.1.6 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size) 231.460 cum 3,279.80 759,142.51

11 BSR 4.1.8 Providingand layinginpositioncement concreteof specifiedgrade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1Cement :4coarsesand :8gradedstoneagregate40mm nominal size) 158.410 cum 2,975.20 471,301.43

12 BSR 4.11 Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size) 199.568 sqm 245.60 49,013.90

13 BSR 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. 128.579 Sqm 436.60 56,137.59

14 BSR 5.1.1 Providingand laying inpositionspecifiedgradeof reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:2 (1 cement:1 coarse sand:2 graded stone aggregate 20mm nominal size) 5.502 cum 5,961.90 32,802.37

15 5.2.1 Reinforced cement concrete work in wall (any thickness), including attachedpilasters,buttresses,plinthandstringcourses, fillets,columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement. 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate 20 mm nominal size) 1.143 cum 6,943.50 7,936.42

16 5.3 Reinforced cement conrete work in beams,suspended floors, roofs havingslopeupto15, landings,balconiec,shelves,chajjas, lintels,bands, plainwindowsills, staircasesandspiral staircasesuptofloor five level excludingthecostofcentring,shuttering, finishingandreinforementwith 1:2:4(1cement:2coarsesand:4gradedstoneaggregate20mmnominal size). 6.316 cum 5,335.90 33,701.54

17 BSR 5.33A.2.2 Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc. 1.140 Cum 5,677.20 6,472.01

18 5.33B.1 Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C 6.316 cum 164.50 1,038.98

19 5.33B.2 Add or deduct for providing richer or leaner mixes respectively at all floor levels. Providing M-30 grade R.C.C. instead of M-20 grade R.C.C. 6.316 cum 164.50 1,038.98

20 5.33.1.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. All works up to plinth level Concrete of M-25 grade with minimum cement content of 330 kg/cum 1129.100 cum 5,063.40 5,717,084.94

21 5.33.2.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. 232.730 cum 5,863.20 1,364,542.54

22 5.33.2.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. 431.861 cum 5,863.20 2,532,087.42

23 BSR 5.9.1 Centring and shuttering including strutting,propping etc. and removal of form for. Foundations, footings, bases of columns etc. for mass concrete. 601.368 Sqm 211.60 127,249.47

24 5.9.3 Suspended floors, roots, landings, balcnies and access platform. 2531.679 Sqm 437.50 1,107,609.56

25 5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cms wide 81.419 Mtr 130.20 10,600.75

26 5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers. 2515.064 Sqm 404.70 1,017,846.40

27 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts 1299.758 Sqm 494.40 642,600.36

28 5.9.7 Stairs,(excluding landings) except spiral-staircaces. 162.551 Sqm 439.90 71,506.18

29 5.9.19 Weather shade,Chajjas, corbels etc. including edges 2.340 Sqm 550.90 1,289.11

30 BSR 5.22.7A Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars TMTC-500-8mm dia. 47538.350 Kg 94.50 4,492,374.08

31 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 47000.939 Kg 92.60 4,352,286.95

32 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 47443.701 Kg 90.80 4,307,888.05 27299

33 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-16mrn to 25 mm Dia . 93116.353 Kg 91.70 8,538,769.57 81897

34 BSR 13.17.1 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement 5.524 Sqm 203.60 1,124.69

35 BSR 13.26 Neat cement punning 5.524 Sqm 40.50 223.72

36 BSR 10.18 Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 42.000 Each 165.40 6,946.80

37 BSR 6.1.14A Brick work with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) 763.706 cum 4,819.90 3,680,986.55

38 BSR 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum 617.215 cum 842.20 519,818.47

39 BSR 6.18.4A Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send) 272.401 sqm 599.30 163,249.92

40 BSR 13.11.4 12 mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) 3654.625 Sqm 141.50 517,129.44

41 DSR 13.86A 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In- Charge. 3.780 sqm 157.20 594.22

42 BSR 13.12.2 15 mm cement plaster on rough side of single or half brick wall of mix. 1:4(1 cement: 4 coarse sand ) 3224.228 sqm 176.40 568,753.82

43 BSR 13.24.2 6 mm cement plaster to ceiling of mix : 1:4 (1 cement: 4 coarse sand) 853.805 Sqm 125.60 107,237.91

44 13.73.1 Colour washing such as green, blue or buff to give an even shade New work (two or more coats) with a base coat of white washing 182.020 SQM 25.90 4,714.32

45 BSR 13.80A.1 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 7596.818 sqm 81.10 616,101.94

46 13.94.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary pain+ of approved brand and manufacture 6.048 SQM 116.50 704.59

47 BSR 13.45.1 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm 3224.228 sqm 215.20 693,853.87

48 BSR 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 390.030 sqm 137.00 53,434.11

49 BSR 13.77.2 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer Two or more coats on new work 4208.410 Sqm 102.30 430,520.34

50 BSR 13.93 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work 32.400 sqm 84.50 2,737.80

51 BSR 10.6.1 Supplyingand fixing-rollingshuters of approvedmake.made of required sizeofM.S.Iathsinterlockedtogether throughtheir intirelengthandjointed togetherat theendbyendlocksmountedonspeciallydesignedpipeshaft withbrackets, sideguidesandarragements for insideandoutsidelocking withpushandpull operationcomplete includingthecost of providingand fixingnecessary27.5cmlongwirespringsmanufacturedfromhightensile steelwireofadequatestrengthconformingtoIS:4454-part1andM.S. top cover of required thickness for rolling shutters. 80x1.25mmM.S. Laths with 1.25mm thick top cover. 13.500 sqm 2,673.70 36,094.95

52 BSR 9.1.1 Providing wood work in frames of doors windows,clerestory windowsand other frames,wrought framedand fixed inpositionwithholdfast lugsor with dash fasteners of required dia& length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood 0.950 Cum 120,526.60 114,500.27

53 BSR 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including stainless steel butt hinges with necessary screws 56.700 sqm 2,845.60 161,345.52

54 BSR 9.5.1 Providingand fixingpanelledor panelledandglazedshutters for doors, windowsandclerestorywindows, including ISImarkedM.S.pressedbutt hingesbright finishedof requiredsizewithnecesseryscrews, excluding panellingwhichwillbepaidforseparately,allcompleteasperdirectionof Engineerin-charge. Second Class teak wood 35 mm thick 8.640 sqm 3,169.50 27,384.48

55 BSR 9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelledandglazedshutters for doors,windowsandclerestorywindows (Area of opening for panel inserts excluding portion inside grooves or rebates tobemeasured). Panelling for panelledor panelledandglazed shutters 25 mm to 40 mm thick: Float glass panes. 5.5 mm thick glass pane. 4.320 sqm 1,576.50 6,810.48

56 BSR 13.101.1 French spirit polishing: Two or more coats on works including a coat of wood filler. 150.768 Sqm 215.80 32,535.73

57 BSR 13.104.1 Polishing on wood work with ready made wax polish of approved brand and manufacture: New work 42.018 Sqm 94.60 3,974.90

58 BSR 26.86.6 Providingand fixing factory made single extruded WPC (Wood PolymerComposite)solid door/window/Ceosetorywindows & other Frames/Chowkhat comprising ofvirgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximumtoxicityindexof12for 100gms) fabricatedwithmiter joints after applyingPVC solvent cement and screwed with full body threaded star headedSS screwshavingminimum frame densityof 750kg/cum, screwwithdrawal strengthof 2200N(Face)& 1100N (Edge), minimum compressive strengthof58N/mm, modulus of elasticity900 N/mmand resistancetospread of flame ofClassA category withproperty of beingtermite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SSdash fastenersof required diaand lengthcomplete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately). Note:ForWPCsolid door/windowframes, minus5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation inprofiledimensions onplussideshall beacceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm 99.000 Mtr 1,182.90 117,107.10

59 BSR 26.87.1 Providing and fixing factory made single extruded WPC {Wood Polymer Composite} solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives {maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N {Face) & 900N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In Charge. {Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick 31.500 Sqm 3,866.50 121,794.75

60 BSR 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding 2661.900 Kg 144.50 384,644.55

61 10.3 Providing and fixing in position collapsible steel shutters with vertical channes20x10x2mmandbracedwith flat irondiagonals20x5mmsize withtopandbottomrailofT-tron40x40x6mmwith40mmdiasteelpulleys completewithbots.nuts lockingarrangement stoppers handies including applying a priming coat of approved steel primer. 42.840 Sqm 6,303.40 270,037.66

62 10.5.1 Providingandfixing1mmthickM.S.sheetdoorwithframeof40x40x6mm angle iron and 3mmMSgusset plates at the junction and corners.all necessary fittingscompletejncludingapplyingaprimingcoat of approved steel primer. 24.120 Sqm 3,653.00 88,110.36

63 BSR 13.82.1 Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: 310.276 sqm 83.50 25,908.05

64 BSR 21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) 294.823 Kg 418.40 123,353.94

65 BSR 21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) 443.896 Kg 480.20 213,158.86

66 BSR 21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness(weight not less than 10kg/sqm) 150.960 sqm 809.30 122,171.93

67 BSR 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) 20 to 25 mm thick - 56.325 sqm 1,252.70 70,558.33

68 BSR 11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm 5.240 sqm 1,334.90 6,994.88

69 BSR 11.56.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete asper the architectural drawings with 18 mm thick stone slab over 20 mm (average)thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 320.936 sqm 3,605.20 1,157,038.47

70 BSR 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 424.402 sqm 795.00 337,399.59

71 BSR 11.41A.3.2 Providing and laying Vitrified tiles infloor indifferent sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming toIS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey [email protected] kg/sqm includinggrouting the jointswithwhite cementandmatchingpigmentsetc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will bedone with thenotch trowel, plier, wedge, clips of required thickness, leveling system and rubbermallet for placing the tiles gentlyand easily. Glazed Vitrified tiles Matt/ Antiskid finish of size Size of Tile 600 x 1200 mm 118.760 sqm 1,356.00 161,038.56

72 BSR 11.41A.1.5 Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 664.288 sqm 1,356.00 900,774.53

73 11.33.2 25 mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete . 2nd class Deodar wood 226.500 sqm 2,683.60 607,835.40

74 BSR 8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 7.141 sqm 4,401.20 31,428.97

75 BSR 12.78.2 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 53.700 mtr 257.50 13,827.75

76 BSR 12.79.1.2 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.Coupler - 110mm 13.000 Each 120.00 1,560.00

79 BSR 12.80.2 Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete. 110 mm 19.000 each 182.72 3,471.68

80 BSR 22.9.2 Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd & 4th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS: 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as lOOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat which shall be paid for separately as per DSR Item No. 12.19 32.500 Sqm 393.30 12,782.25

81 BSR 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni). 197.058 Sqm 480.60 94,706.07

82 BSR 22.8.1 Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water-proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge. 1147.992 Sqm 850.70 976,596.79

83 BSR 8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and 8.640 Sqm 3,542.90 30,610.66

84 10.32.1 Steel work welded in built up sections/framed worK including cutting hoisting, rixing inpositionandapplyingaprimingcoat of approvedsteel primer using structural steel, etc. as required. Instringers, treads landingsetc. of stair cases includinguseof required plates wherever required all complete. 4883.328 Kg 104.00 507,866.11

85 BSR 10.2 Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete 52250.000 kg 95.40 4,984,650.00

86 BSR 12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1250.000 sqm 625.10 781,375.00

87 BSR 12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws complete : 55.285 Sqm 396.80 21,937.09

88 12.51.6 Gutter (600 mm over all girth) 92.142 Mtr 898.70 82,808.02

89 BSR 12.57X Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge. 1250.000 Sqm 259.80 324,750.00

90 12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 1506.148 Sqm 993.00 1,495,604.96

91 DSR 26A.1 Providing and supplying aluminium extruded tubular and other aluminiumsectionsasper therchitectural drawingsandapproved shopdrawings, thealuminiumqualityaspergrade6063T5orT6as perBS74,includingsuperdurablepowdercoatingof60-80microns conformingtoAAMA2604ofrequiredcolourandshadeasapproved bytheEngineer-in-Charge. (Theitemincludescostofmaterialsuch ascleats,sleeves,screwsetc.necessaryfor fabricationofextruded aluminium frame work. Nothing extra shall be paid on this account). 952.000 Kg 370.40 352,620.80

92 DSR 26A.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (doubleglazed)visionpanelunitsofsizeandshapeasrequiredand specified,comprisingofanouterheatstrengthenedfloatglass6mm thick, of approvedcolourandshadewithreflectivesoftcoatingonsurface# 2of approvedcolour andshade, an innerHeat strengthnedclear floatglass6mmthick,spacertube12mmwide,dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the requiredperformances, asper theArchitectural drawings, asper theapprovedshopdrawings, asspecifiedandas directedbytheEngineer-in-Charge.TheIGUsshallbeassembledin thefactory/workshopof theglassprocessor. (Payment for fixingof IGU Panels in the curtain glazing is included in cost of item No.26.2)Forpayment,onlytheactualareaofglassonface#1of the glass panels (excluding the areas of the grooves andweather siliconesealant)providedandfixedinposition,shallbemeasuredin sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coatingonface#2,+12mmAirgap+6mmHeatStrengthenedclear Glass of approved make having properties as visible Light transmittance(VLT)of25to35%,Lightreflectioninternal10to15%, light reflection external 10 to 20 %, shading coefficient (0.25 0.28)andUvalueof3.0to3.3W/m2degreeKetc.Thepropertiesof performance glass shall be decided by technical sanctioning authority as per the site requirement. 112.000 Sqm 3,377.50 378,280.00

93 BSR 10.36 Providingand fixingstainlesssteel (Grade304) railingmadeofHollow tubes,channels, platesetc., includingwelding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessarystainlesssteelnutsandboltscomplete, i/cfixingtherailingwith necessaryaccessories&stainless steel dash fasteners , stainlesssteel boltsetc.,of requiredsize,onthetopof theflooror thesideofwaistslab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). 867.366 Kg 546.80 474,275.73

94 BSR 10.20.2 Chequerredprecast cement concrete tiles22mmthickwithmarbie chipsof size6mmin footpath&coutyard jointedwithneat cement slurrymixedwithpigment tomatchtheshadeof tilesincludingrubbing andcleaning tec. Completeon20mmthickbedof cementmortar 1:4(1 cement:4 coarse sand) 72.757 Sqm 953.10 69,344.70

95 BSR 22.24 Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry- shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakage 24.026 Sqm 265.80 6,386.11

96 BSR 22.23.1 Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry- shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakage 24.420 Sqm 406.20 9,919.40

97 10.32.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 8750.700 Sqm 114.60 1,002,830.22

98 26.91 Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately. 127.725 Sqm 3,081.60 393,597.36

99 MR Providing and fixing factory-made acoustically treated door suitable for auditorium use, consisting of double-leaf / single-leaf door shutter made of 1.2 mm thick GI sheet on both sides, internally filled with high-density rockwool insulation (minimum 48 kg/m³) for effective sound attenuation. The door shall be mounted on a 1.6 mm thick pressed steel door frame, complete with acoustic rubber gaskets, perimeter sealing and drop-down acoustic seal to prevent sound leakage. The door shall achieve a minimum sound reduction rating of Rw 35–40 dB. The door assembly shall be provided with SS heavy-duty hinges, door closer, mortise lock / panic bar (for exit doors) and all necessary hardware. Finish shall be powder coated / laminate / veneer as approved by the client. Installation shall be complete in all respects, including fixing, alignment, testing and commissioning. 24.480 Sqm 19,368.00 474,128.64

100 Supply Caraige of materials 0.000 0 0.00 0.00

Add Extra cost of Material 0.000 0 0.00 0.00

SEIGNIORAGE FEES 0.000 0 0.00 0.00

Plumbing 0.000 0.00 0.00

101 BSR 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 10.000 Each 4,470.90 44,709.00

102 BSR 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 12.000 Each 4,230.00 50,760.00

103 BSR 17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap 21.000 each 2,369.90 49,767.90

104 BSR 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern 12.000 each 3,723.20 44,678.40

105 BSR 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 12.000 each 299.40 3,592.80

106 BSR 17.32.2 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm 21.000 Each 857.00 17,997.00

107 BSR 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 21.000 Each 146.30 3,072.30

108 BSR 12.78.1 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 75 mm diameter 66.000 Metre 162.70 10,738.20

110 BSR 12.79.3.1 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW) Single tee with door 75x75x75mm 12.000 Each 141.60 1,699.20

112 12.79.4.1 Single tee without door-75x75x75mm 12.000 Each 124.20 1,490.40

116 BSR 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 15 mm nominal outer dia pipes 132.000 metre 278.20 36,722.40

117 18.8.2 20mm nominal outer dia pipes 132.000 metre 350.80 46,305.60

118 BSR 18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25mm nominal outer dia pipes 176.000 metre 317.30 55,844.80

119 18.7.4 32mm nominal outer dia pipes 176.000 metre 395.20 69,555.20

120 BSR 18.17.1 Providing & fixing gun metal gate valve with C.I. wheel of approved quality, (screwed end) : 25 mm nominal bore 4.000 each 532.30 2,129.20

122 BSR 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 22.000 each 434.20 9,552.40

123 BSR 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore 33.000 Each 594.80 19,628.40

124 BSR 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe 370.000 metre 410.70 151,959.00

125 BSR 24.4.1 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia 30.000 Mtr. 573.10 17,193.00

126 BSR 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in- charge. 5.303 Cum 1,188.90 6,304.74

127 BSR 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 5.303 Cum 1,195.60 6,340.27

128 BSR 24.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. 3.535 Cum 1,195.60 4,226.45

129 BSR 19.30.1.1 Constructing brick masonry chamber forunderground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 18.000 Each 4,266.80 76,802.40

130 BSR 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 4000.000 Ltr 9.70 38,800.00

131 BSR 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2.000 Each 33,603.40 67,206.80

DEEP BORING 0.000 0.00 0.00

132 BSR 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia 120.000 Mtr. 486.80 58,416.00

133 BSR 24.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia 30.500 Mtr. 660.10 20,133.05

134 24.3.5 75 mm nominal size dia 41.800 Mtr. 414.40 17,321.92

135 BSR 24.4.5 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 75 mm nominal size dia 18.300 Mtr. 482.10 8,822.43

136 BSR 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. 5.565 Cum 1,343.20 7,474.91

137 BSR 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. 10.000 Hour 916.80 9,168.00

138 BSR 24.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia 1.000 Each 210.70 210.70

139 BSR 24.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp 1.000 Each 1,531.40 1,531.40

140 BSR 24.15.1 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia 5.000 Each 228.30 1,141.50

141 BSR 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work40 mm nominal outer dia Pipes 50.000 Mtr. 477.60 23,880.00

142 BSR 18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore 1.000 Each 707.30 707.30

Add 6% GST beyond 12% (Multiplying Factor - 1.0536) = B 0.000 0.00 80,616,198.73

ELECTRICAL 0.000 0.00

143 1.3.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.l. box etc as required. Group C 234.000 Point 1,146.00 268,164.00

145 1.4 Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate suitable G.I. box etc. required. 6.000 Point 1,248.00 7,488.00

146 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit along with 1 Nos 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required. 720.000 Meter 309.00 222,480.00

147 1.7.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 2020.000 Meter 201.00 406,020.00

149 1.7.11 4 X6 sq. mm + 1 X 6 sq. mm earth wire 300.000 Meter 660.00 198,000.00

151 1.24.1 Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch 240.000 Each 82.00 19,680.00

152 1.24.4 3 pin, 5/6 amps socket outlet 34.000 Each 112.00 3,808.00

153 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as req u ired. 39.000 Each 358.00 13,962.00

154 1.31 Supplying and fixing suitable size Gl box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. 31.000 Each 414.00 12,834.00

155 1.32 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 31.000 Each 531.00 16,461.00

156 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. 39.000 Each 64.00 2,496.00

157 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. 54.000 Each 80.00 4,320.00

158 1.41 lnstallation, testing and commissioning of pre-wired, flourescent fitting / compact flourescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated. Copper conductor , single core cable and earthing etc. as required. 1.000 Each 134.00 134.00

159 1.45 lnstallation, testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto cm ) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheeL cover on the fan box etc. as reo u ired. 1.000 Each 203.00 203.00

160 2.9.1 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus -bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required, (But without MCB/RCCB/lsolator) 4 way (4 + 12), double door, horizontal type 13.000 Each 4,184.00 54,392.00

161 2.9.3 8 way (4 +24), double door, horizontal type 10.000 Each 6,199.00 61,990.00

162 2.12.1 Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required' 6A to 32 amps, Single pole 13.000 Each 237.00 3,081.00

163 2.16.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amps 10.000 Each 967.00 9,670.00

165 3.2 Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required. 2.000 Each 6,323.00 12,646.00

166 3.7 Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with Gl thimble as required. 80.000 Metre 37.00 2,960.00

167 3.10 Supplying and laying 25 mm X 5 mm copper strip in 40 mm dia G.l. pipe from earth electrode, including connection with brass nut, bolt. spring, washer excavation and refilling etc. as required. 40.000 Metre 1,628.00 65,120.00

168 3.21 Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for eafth electrode to fill up the excavated earth and earth inspection pit etc. as required. 2.000 Set 16,675.00 33,350.00

169 4.2 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.l. tube, having single prong at top, with 85 mm dia 6 mm thick G.l' base plate including holes etc. complete as required. 2.000 Each 416.00 832.00

170 4.4 Jointing copper/ G.l. tape (with another copper/ G ltape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. 2.000 Each 81.00 162.00

171 4.7 Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run) 60.000 Each 102.00 6,120.00

172 4.8 Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run) 60.000 Each 145.00 8,700.00

173 4.12 Providing and fixing testing joint made of 20 mm X 3 mmthick G.l. strip, 125 mm long, with 4 nos. of tlnned G.l. bolts, nuts, chuk nuts and spring washers etc. complete as req uired. 2.000 Each 102.00 204.00

174 5.3 Supplying and fixing 4'X20 watt LED batten with minimum efficacy 100 lm/w in aluminium housing and complete with integrated electronic driver etc directly on walll ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. (For Non-residential building) 43.000 Each 762.00 32,766.00

175 5.14.4 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required. 90 Watt 3.000 Each 5,516.00 16,548.00

176 5.5 Supplying and fixing replaceable compact commercial batten suitable for Double TB LED tube complete with 20 watt LED polycarbonate TB tube with built in driver etc. directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. 24.000 Each 1,232.00 29,568.00

177 5.8.2 Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 15 watt 24.000 Each 1,608.00 38,592.00

179 6.1.5 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required. 12 watt LED Lamp 32.000 Each 239.00 7,648.00

181 7.1.2 Laying of one number PVC insulated and PVC Sheathed/ XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 35 sq.mm. and upto 95 sq.mm 170.000 Mtr. 326.00 55,420.00

182 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.. 39.000 Each 2,482.00 96,798.00

183 8.17.1 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required. 300 mm sweep 12.000 Each 2,572.00 30,864.00

184 Supply, Pg No. - 18 2208 Supplying 3.5 core, 70 Sq.mm XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminum conductor 520.000 mtr 604.90 314,548.00

MAIN PANNEL 0.000 0 0.00 0.00

185 BSR 2018 -8.10.3 Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 40mmx40mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switchgears. 0.000 0.00 0.00

190 2.5.3 200 amp 415 V heavy duty three phase with neutral busbar chamber. 2.000 Nos 12,132.50 24,265.00

191 Supply, Pg-20, 2313 Pilot lamp for indicator, RYB 6.000 Nos 195.73 1,174.38

192 Supply, Pg-20, 2314 Selector switch 6.000 Nos 396.75 2,380.50

193 Supply, Pg-20, 2312 DIGITAL MULTIMETER (3phase ) 2.000 Nos 3,904.02 7,808.04

195 8.12 Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.) 64.000 SQF 2,600.15 166,409.60

LANDSCAPING 0.000 0.00

196 BSR 23.1 Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of/and manure before and after flooding trench with water (encluding cost of imported earth,sludge or manure). 18.000 sqm 44.70 804.60

197 BSR 23.2 Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks will be reduced by 20% for payment). 10.800 cum 143.50 1,549.80

198 BSR 23.3 Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment). 5.400 cum 282.60 1,526.04

199 BSR 23.4.1 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of l.S. designation 20 mm 5.400 cum 278.90 1,506.06

200 BSR 23.5 Rough dressing the trenched ground including breaking clods 0.180 100sqm 85.90 15.46

201 BSR 23.6 Uprooting weeds form the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. 0.180 100sqm 283.20 50.98

202 BSR 23.7 Fine dressing the ground 0.180 100sqm 208.80 37.58

203 BSR 23.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately). 5.400 cum 30.10 162.54

204 BSR 23.9 Mixing earth and sjudge or manure in porportion specified or directed. 5.400 cum 20.90 112.86

205 BSR 23.10.2 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. 0.180 100sqm 670.80 120.74

206 BSR 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts. 0.180 100sqm 3,418.20 615.28

207 BSR 23.14.2 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2;1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water,dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately): 50.000 each 69.30 3,465.00

208 BSR 23.15.1 Half brick circular tree guard in 50 class designation bricks, internal diameter 1.25 metre and height 1.? metre above ground and 0.20 m below ground bottom two courses laid dry and top three courses in lime mortar 1:2(1 lime putty:2 surkhi) or cement ortar 1:6 (1 cement:6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: 50.000 each 1,647.60 82,380.00

209 BSR 23.19.1.2 Edging with bricks laid dry length wise including excavation, refilling, consolidating with hand packing and spreading neatly susrplus earth within a lead of 50 m: 100.000 Mtr 38.10 3,810.00

210 BSR 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%). flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) 36.000 cum 126.90 4,568.40

211 2.29.1 Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm 10.000 Each 225.05 2,250.50

212 DSR HOR 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge 20.000 Per Qtl 610.70 12,214.00

213 DSR HOR 2.38 Topiary cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topiary) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. 20.000 per plant per month 83.95 1,679.00

214 DSR HOR 2.53 Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge 10.000 per plant per month 932.95 9,329.50

215 RCD 11.20 Providing and fixing tree guard 0.60 metre square, 2.00 metre high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm and steel wire3 mm dia welded and fabricated as per design in two halves bolted together 10.000 Each 3,480.30 34,803.00

216 DSR HOR 2.57.1 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) 5.000 Each 7.30 36.50

217 DSR HOR 3.18 Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge. 5.000 Each 157.85 789.25

218 DSR HOR 3.85 Providing and displaying of Schefflera high colour having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. 5.000 Each 41.00 205.00

219 DSR HOR 4.1 Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 43.05 215.25

220 DSR HOR 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. FOR FRENCH GARDEN 5.000 Each 20.00 100.00

221 DSR HOR 7.74 Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge. 5.000 Each 80.00 400.00

222 DSR HOR 6.7 Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 5.000 Each 20.00 100.00

223 DSR HOR 7.76 Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge. 5.000 Each 80.00 400.00

224 DSR HOR 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 5.000 Each 20.00 100.00

225 DSR HOR 7.28 Providing and stacking of Ficus benjamina (green) of height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 105.00 525.00

226 DSR HOR 5.12 Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. 5.000 Each 322.90 1,614.50

227 DSR HOR 4.42 Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 32.80 164.00

228 DSR HOR 4.44 Providing and Displaying plants Nasturtium in different colour well developed with fresh & healthy foliage with full bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.. 5.000 Each 54.35 271.75

229 DSR HOR 4.70 Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 64.60 323.00

230 DSR HOR 8.9 Supply and stacking of plant Cassia biflora of height 60-75 cm. with 4-5 branches in poly bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 55.00 275.00

231 DSR HOR 4.88 Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.. 5.000 Each 46.15 230.75

232 DSR HOR 9.8 Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. 5.000 Each 30.00 150.00

233 DSR HOR 4.91 Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. 5.000 Each 32.80 164.00

234 DSR HOR 7.65 Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge. 5.000 Each 550.00 2,750.00

235 DSR HOR 7.10 Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 180.00 900.00

FIRE FIGHT 0.000 0.00 0.00

236 18.7.7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/1S 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 100mm dia 80.000 mtr 2,555.00 204,400.00

243 18.14.7 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 a)mplete with rubber qasket. Gl bolts, nuts, washers etc.as required 100mm dia. 1.000 Each 17,786.00 17,786.00

244 18.15.3 Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of I .6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 MM 1.000 nos 11,144.00 11,144.00

245 18.11.6 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 100mm dia 1.000 nos 8,960.00 8,960.00

246 18.10.1 Supplying and fixing Single headed extemal yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290a) Single Headed (type A) with blank Gunmetal/StainIess Steel and chain as reauired • 6.000 each 7,646.00 45,876.00

247 18.16.1 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe With 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforminq to IS 636 (type-A) as required Gun Metal 6.000 each 5,202.00 31,212.00

248 18.18.1 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe couolinq as required: Gun Metal 6.000 each 2,416.00 14,496.00

249 18.17.1 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle, Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 mtr. 5.000 each 8,675.00 43,375.00

250 18.21.1 Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler 35.000 nos 522.00 18,270.00

251 18.19.1 Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe 1.000 nos 6,742.00 6,742.00

252 18.20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Air Release Valve 25mm 1.000 nos 18,244.00 18,244.00

253 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore 5.000 nos 399.15 1,995.75

B) FIRE PUMPS & PANELS EQUIPMENTS 0.000 0 0.00 0.00

254 18.4.2 Terrace pump 450 lpm, 30 M head (A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting Of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump Of iron body & bronze impeller With stainless steel shaft, confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply With IP55 class Of protection for enclosure, horiziontal foot mounted type with Class-'F insulation, to IS-325. (D) M.S. fabricated common base plate, guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 1.000 set 86,203.00 86,203.00

255 18.5.1 Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated Of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50HzAc Supply with enclosure protection class IP42 as required : 1.000 set 245,730.00 245,730.00

C) FIRE DETECTION SYSTEM 0.000 0 0.00 0.00

256 17.1.9.1 Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, as reauired. 4 Zone 1.000 nos 8,866.00 8,866.00

257 17.2.9 Supplying installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed Tempreature thermistor complete with base as required. 20.000 nos 2,726.00 54,520.00

258 17.1.3 Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. 5.000 nos 474.00 2,370.00

259 17.1.6 Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged a)ver plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. 5.000 nos 557.00 2,785.00

260 17.5.3.1 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm 1000.000 mtrs 54.00 54,000.00

Total = A+B+C+D 85,225,536.14

Rupees Eight Crore Fifty Two Lakh Twenty Five Thousand Five Hundred Thirty Six Only

Part B (Non Schedule Items of Work, for which tenderer have to quote Item wise rate inclusive of all taxes)

Non Schedule Items 0.000 0.00

NS-1 GEM S/F/F Kalinga 3 Core Copper(EC grade) Submersible Flat Cables for Submersible Pumps KalingaR (KALINGA THREE CORE 4 SQMM CABEL) Product ID : 5116877-43377957844 30.000 Mtr. 0.00

NS-2 GEM S/F/F LIDER 2 HP Starters Control Panel for Submersible Pump LIDERR (LIDER[LS-DOL-SPP 2 H.P]DOL-STARTER) Product ID : 5116877-20575423238 1.000 Each 0.00

NS-3 GEM Supplying fitting & fixing crompton 2.2 kiloWatt 30 LPS Three Phase-Submersible Pump Set cromptonR (CROMPTON 2 hp Three Phase-Submersible Pump Set -CROMPTON) Product ID : 5116877-77824849883 1.000 Each 0.00

NS-4 GEM Devraj Mild Steel sheet Double Door with locking arrangment(4) Fire Hose Cabinet, Warranty 1 Year 6.000 each 0.00

FURNITURE 0.000 0.00

NS-5 The seat frame assembly shall be ERW Tube / IS :3074-2005 GRADE 1: 19 mm dia Round Pipe 1.2mm Thickness . The Seat profile shall be developed to help the users to get necessary comfort in popliteal region and ease of use in forward push for the seat sliding feature.Seat size shall be: 40.5 cm. (W) x 49 cm (D) x 12.5 cm (T)(Front) & 8 cm(T)(Rear). The backrest assembly shall be made of ERW Tube / IS :3074-2005 GRADE 1: 16 mm dia Round Pipe 1.63 mm Thickness & Extra Reinforcement 16 dia round pipe 1.2 mm. The back foam shall be designed with contoured lumbar support for extra comfort at upright and tilted conditions. The back shall be: 47 cm. (W) x 82.3 cm (H) x 11.0 cm (T)(Front) & 6cm (T)(Rear). The Automotive grade HR polyurethane foam for Seat and Back shall be moulded with Density = 55 +/- 5kgs/cu.m. as per JIS K 6401 with compression max 13%. The back & seat covers are made of injection moulded thermoform PPCP as per IS: 10915-1984 with 45.7 cm(W)x 75.5 cm(H)x 2.3mm(T) for back and 43.5 cm(W)x 55.2 cm(D)x 2.3mm(T) for seat. The armrest shall be made up of Polyurathane/wood with waterfall edge design. The armrest shall be available with Polypropelene Cupholder . For Push Back mechanism – Coil Spring / Spring Steel IS : 4454 1981 GRADE 2. The fluimatic slider travels upto 60mm with metal ball and roller cage which results in PUSH BACK OF 140 + 10mm . Should have flexibility to restrict movement of the pushback and slider as per availability of aisle space. The mechanism houses the seat & back and shall has a special feature of upright resistance lock to avoid activation of sliding feature unless enough force shall be applied by user when tilting shall be required. For Auto Tip-up – Torsion Spring / Spring Steel IS : 4454 1981 GRADE 2 (part i). The chair shall rests on the ground on two Side wing frame with plywood with upholstery. Each Leg is a rectangular tube of cross section 50mm X25mm x1.63mm Thickness as per IS:4923-1985 standards . The side panel frame is made of HRPO sheet metal as per IS :1079 -1994 standards alongwith fabric upholstered plywood. It shall be grouted to the floor using 2 nos. anchors for each panel through the base plate. All steel components shall be zinc passivated and powder coated (DFT 40-60 microns). The heavy duty 100 % polyester dyed yarn with 3mm + 0.5mm foam backing fabric is available in shades as per Wipro Box Office shade card. FR grade material confirms to IS 15061. The auditorium chair shall be designed to get mounted/grouted on floors with concrete(min 100 mm) or wooden flooring(min 50 mm) with specific grouting bolts. Provision for lights on sides for seats along the aisles using PP housing with 12mm watt lamp. Aluminum cut-outs available for row & seat numbering. Overall Dimensions shall be Seat Height - 45 cm, Height - 104 +/- 1 cm,min armrest c/c - 53.3 cm, Width & Depth as measured from base - Width-66.0 cm and Folded Depth-66.0 cm, Normal depth-76cm, Extended depth- 92 cm. Dimensions tolerance / variations shall be within +/- 1 cm. 750.000 Each 0.00

NS-6 Supply and installation of Carpet, Loop pile, Gauge 1/10, height 6mm, pile weight 550-600 gm/sqm, roll width 2M to be installed in floor with adhisive, to be complete in all respect as per direction of engineer in charge. 832.000 Sqm 0.00

NS-7 Supply Installation Testing & Commissioning of Dom ip camera 2 MP 120db WDR.3D-DNR, day night (ICR) ROI, Defog, AWB,AGC, BLC HLC ,1/2.7" 2 MP PS CMOS Image sensor, Max 25/30fps @1080 P ,H .265+/H.265 dual sream endcoding,2.8 mm fixed lens (3.6mm optional), IP67, support PoE, Support mobile software ,CMS software' etc as required Make-CP PLUS 28.000 Each 0.00

NS-8 Supply Installation Testing & Commissioning of Network rack 4U for CCTV survilacne device with complete accessoreis, 1 PDU with 6nos of 5A socket 15 AMP Switch, Fan, wire manager of Netrack make etc asrequired. 1.000 Each 0.00

NS-9 Supplying and drawing of UTP 4 Pair CAT-6 LAN cable in the existing surface / recessed PVC concuit etc. as required. 915.000 m 0.00

NS-10 Supply Installation Testing & Commissioning of Network Vedio Recorder up to 32 IP camera input, spport 4SATA TB Hard Disk up to 24 TB , 2 USB .Max 200 Mbps incoming bandwidth, VGA, HDMI simultaneous vidio outputs, H.265, H.264 dual codec decoding , up to 8 Mp resulution preview and play back,ONVIF Version 2.4 conformane support mobile software and CMS software etc as required (Make -CP PLUS) 2.000 Each 0.00

NS-11 Supply Installation Testing & Commissioning of 4 TB Seagate Window surveillance Hard Disk etc as required 2.000 Each 0.00

NS-12 Supply installation testing & commissioning of Network Switch 24 port Poe manged gigabyt 24 # 10/100/1000 Base-T auto-sensing PoE+ ports. 2 dedicated 100/1000 Base-X Fiber SFP ports. Bandwidth: 52 Gbps non-blocking. MAC Address database size: 8,000 media access control (MAC) addresses. Max power (worst case, all ports used, full PoE, line-rate traffic) (Watts): 228.53 W. Make - Netgear, cp-plus,) 5.000 Each 0.00

NS-13 Supply installation testing & Commissioning of 43" Display for CCTV live View & Recording . Screen Size-43" or Higher . Monitor Type-LED. Panel Technology-IPS. Native Resolution-1,920 x 1,080 (Full HD). Brightness-350cd/m2 or higher. Contrast Ratio-1,100 : 1 or higher. Inputs HDMI, DVI-D, RGB, Stereo Mini Jack, USB. Outputs Stereo Mini Jack, External Speaker Out. External Control-RS232C (In/Out), RJ45, IR Receiver. Make - Lg, Sony, Samsung 1.000 Each 0.00

NS-14 Supply Installation Testing & Commissioning of DIGISOL RJ45 CONNECTOR 2.000 Each 0.00

NS-15 Supply Installation Testing & Commissioning of Electric Wire Anchor 3.000 rol 0.00

ACCOUSTIC 0.000 0.00

NS-16 Providing and fixing, in position concealed G.I. section for wall panelling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm., Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200 mm C/C, all complete as per the drawing & directions of engineer-in-charge., The joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength of 225 kg/sqcm. 840.750 sqm 0.00

NS-17 Anutone Strand 1 Melange 600x1200x20mm, Square EdgeSupply and Installation of Anutone Strand 1 Melange, square edge, magnesite bonded 1mm wide pinewood fibre core tiles,GreenPro certified, of size 600x1200x20mm, volume density 400kgs/m3, weight 8kg/m2 installed by using Anutone Strut framework system and Strut Z-Bars. "The Strut framework systems includes Anutone Strut CC22 thickness 0.50mm, length 3600mm, knurled web 40mm, depth 22mm and equal flanges 13mm is fastened to wall positioned horizontally in a regular manner at 600mm centres. Anutone Strut H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Strut CC22 at 600mm centers. The Strand 1 primer, Kerfed long edge panels shall then be inserted into the Strut H-Spline along their long edges of 2400mm to perfect fit with staggered short edges." 642.404 sqm 0.00

NS-18 Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 118.000 Each 0.00

NS-18 GEM fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B 5.000 nos 0.00

NS-19 GEM Ecofire Portable Fire Extinguishers as per IS 15683 (2018) Low Pressure Extinguisher (Service Pressure ≤19 bar) Powder Based (as per IS 4308 ) Class -A 20.000 nos 0.00

NS-20 GEM PALEX 10 liter GALVANIZED MILD STEEL FIRE BUCKET (Fire suppression hand tools) PALEX (FBSTAND10LTR) 1.000 nos 0.00

AUDIO VISUAL 0.000 0.00

NS-21 90° x 50° Coverage for broad, even sound distribution,2265H 15-inch 2 Way Differential Drive® LF Driver for deep, powerful bass, 2432H HF Compression Driver with 75mm (3") voice coil for crystal-clear highs, Large PT™ Progressive Transition Waveguide for accurate pattern control Rotatable waveguide for vertical or horizontal installation, Bi-Amp/Passive Switchable for flexible operation, FIR Tuning for Frequency & Phase Optimization, Heavy-Duty Birch Plywood Enclosure for durability 4.000 Units 0.00

NS-22 Custom Array Frame 4.000 Units 0.00

NS-23 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

Main Subwoofer 0.000 0.00

NS-24 Dual 18-inch SVG drivers with 4-inch voice coils , Large vent area for high output with low distortion , Switchable parallel/discrete input modes , Durable 11-ply Finnish birch plywood enclosure , 12 M10 threaded suspension points for mounting Transducer Power Rating (AES) , 2400 W (9600 W peak), System Power Rating , Maximum SPL (1m) 30 Hz – 100 Hz: 136 dB-SPL cont avg (142 dB peak)100 Hz – 500 Hz: 136 dB-SPL cont avg (142 dB peak) , System Sensitivity (1w @ 1m) 30 Hz – 100 Hz: 102 dB 100 Hz – 500 Hz: 102 dB 2.000 Units 0.00

NS-25 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

NS-26 Back Fills Ultra compact enclosure , 6.5 in LF transducer , 90° x 90° Progressive Transition™ waveguide with a (1 in) exit compression driver Dual Neutrik NL4 connectors plus screw terminals Frequency Range (-10 dB): 55 Hz - 20 kHz Frequency Response (+/-3 dB): 65 Hz - 18 kHz Directivity Factor (Q): 7 (avg. 500 Hz - 16 kHz) Long-Term System Power Rating3: (Continuous/Program/Peak): 160 W / 320 W / 640 W 10.000 Units 0.00

NS-27 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

NS-28 Stage Monitors Powered: Yes , LF Driver Size:12″ woofer , HF Driver Size:1.5″ Neodymium , Total Power:2000W Peak, 1000W RMS , Inputs:2 x XLR-1/4″ combo, 1 x 1/8″ , Outputs:2 x XLR (thru). 1 x XLR (mix out) ,\Frequency Range:50Hz-20khz (-10 dB) , Crossover Frequency:2050Hz , Maximum Peak SPL:132dB SPL , Horizontal Coverage Angle:90° , Vertical Coverage Angle:50° 3.000 Units 0.00

NS-29 a 2-channel audio device for eliminating feedback in live sound, featuring 24 filters/channel, 24-bit/48kHz conversion, XLR/TRS I/O, Type IV Conversion, Wizard setup function, and a full LCD display, offering professional audio control with dynamic range>> and low THD. Specifications include +20dBu max output, 113dB A/D dynamic range, 0.003% THD 1.000 Unit 0.00

NS-30 Signal Processing 12x8 (12 analog inputs, 8 analog outputs) digital signal processor (DSP) in the Soundweb London family, featuring configurable processing, a 48-channel low-latency digital audio bus (BLU link), 12 control inputs, and 6 logic outputs for GPIO integration, all in a 1RU chassis, ideal for tailored audio systems in commercial venues. It uses standard Cat5e for the BLU link, supports remote control via HiQnet Audio Architect, and offers phantom power per channel 1.000 Unit 0.00

NS-31 The BSS BLU-BOB2 is a 1RU rack-mount break-out box with 8 analog audio outputs, expanding the Soundweb London network with low-latency, fault-tolerant BLU-Link digital audio, configured via rear DIP switches for 8-channel blocks from the 256-channel bus, featuring Phoenix connectors for audio/power, 12V DC power, and <0.01% THD performance. Audio Outputs: 8 electronically balanced line outputs on Phoenix/Combicon connectors. Digital Audio Bus: 256-channel, low-latency, fault-tolerant BLU-Link (via RJ45). Configuration: DIP switches for channel range selection 1.000 Unit 0.00

NS-32 32 Mic Inputs 8 XLR/1/4" Combi-jacks for line inputs and instruments 40 DSP input channels (32 mono inputs and 4 stereo channels/returns) 31 Output busses (All with full DSP processing and GEQ) 4-band Fully Parametric EQ on each channel and bus 1.000 Unit 0.00

NS-33 RJ45/Cat5 connectivity, for 100M runs between stage and mixing console (328 feet) 32 remote controlled mic preamps and AD converters 12 XLR analog line level outputs 3U Rack mount design 1.000 Unit 0.00

NS-34 Microphone Wired Vocal Microphone Frequency response tailored for vocals, with brightened midrange and bass rolloff Uniform cardioid pickup pattern isolates the main sound source and minimizes background noise Pneumatic shock-mount system cuts down handling noise 2.000 Units 0.00

NS-35 Wired Instrument Microphone The Shure Beta 57A is a dynamic instrument microphone with a supercardioid polar pattern, offering a tailored 50Hz-16kHz frequency response, 150-ohm impedance, and a rugged build for live and studio use, providing superior rejection of off-axis sound and high gain-before-feedback for instruments like guitars, drums, and brass. 2.000 Units 0.00

NS-36 Wireless Handheld Microphone SVX4 Diversity Receiver. SVX2 Handheld Microphone Transmitter with PG58 Microphone. Frequency Response 60 Hz - 15 KHz. Customized frequency response is smooth and extended. It is specifically tuned for audio use. Cardioid detection pattern rejects off-axis sounds and provides good front feedback. The dynamic cartridge has a simple, solid coil so it can handle high sound levels without any distraction. The steel tennis ball has a "pop" filter grille to reduce breathing noise and wind noise. 2.000 Units 0.00

NS-37 Wireless Lavalier Microphone professional subminiature cardioid lavalier microphone known for its small size, durable Kevlar- reinforced cable, and CommShield® technology, offering wide frequency response (20Hz-20kHz) for natural voice reproduction, with versions available 2.000 Units 0.00

NS-38 Accessories 24-Port Gigabit Unmanaged PoE+ Switch with a 380W power budget, offering 24 Gigabit Ethernet ports (24 PoE+) supporting up to 30W per port for IP cameras, VoIP phones, and APs, with plug-and-play setup, fanless silent operation, rack/desktop mounting, and Energy-Efficient Ethernet (EEE) 1.000 Unit 0.00

NS-39 Speaker Cables 1500.000 Mtr 0.00

NS-40 42U Equipment Rack 1.000 Unit 0.00

NS-41 Connector & Other Accessories 1.000 Lot 0.00

NS-42 Projector-7000 Lumens Smart 4K UHD HDR Laser Projector All-around Projector for Versatile Fields Laser 4K UHD & 3M:1 CR Exceptional Picture Quality With 8.3 mega pixels utilizing 4K UHD (3840 x 2160) resolution, crisp details from 40 to 300-inch screens. With 3M:1 contrast ratio, it can express deep darkness and brightness. 7,000 ANSI Lumens Brightness Great Color Even in Bright Laser (up to 20,000 hours) throw Ratio 1.53 to 2.45 Keystone 25-Point Keystone Adjustment (auto) Lens Shift H: +/- 28%, V: +60%/-33% (auto) Noise 31dB to 35dB Aspect Ratio 16:9Zoom 1.6x (auto) Screen Size - upto 300” HDR yes Connection Terminals HDMI 2.0 in (x3), HDMI out (x1) , DisplayPort (x1), USB Type-A 2.0 (x2), RJ45 (x2), HDBaseT, RS-232c (in/out), IR (in), Audio 3.5mm (in) 1.000 Unit 0.00

NS-43 275 inch Diagonal Projector Screen with 16:9 Aspect Ratio Mounting Method: Wall, Material: HD Matt White Fiber Glass, Color: White, Projection For Which Designed: Projector, Foldability: Inflateble 1.000 Unit 0.00

NS-44 HDMI Cables & Connectors and additional accessories 1.000 OEM 0.00

NS-45 Low Noise Motorized Projector ceiling Lift 1.000 Unit 0.00

NS-46 matt texture finish - Light Source • LED Lamp: 3V DC SMD LED ARRAY • Base color : RGBW • LED Configuration : 12Red, 18Green, 18Blue, 6White Optical System • Light Beam Angle : 15° or 25° • Panel lens: PMMA LENS ARRAY combined with a special optical design produces uniform and pleasant lighting even when used with a mixture of different LEDs • Power Supply Unit, Input: AC 100 - 260V 50/60Hz Output: 24V DC, electronic flicker-free power supply. • Lighting Fixture must be provided with Minimum 3 Mtr Length (2.5 Mtr Length Power In Cable + 0.5 Mtr Power out Cable) 3 core 1.0Sq mm FRLS & ISI mark cable with 3pin IEC Male Plug Mandatory. • Lighting fixture must be properly earthed and earthling cable should be connected with power supply chord. Control System • Control Protocol : RDM & Manual • Mandatory Accessories supplied along with Lighting Fixtures 1) Spud 28 mm Spigot with M12 thread •Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning 8.000 Units 0.00

NS-47 SITC of CE Certified 100W LED Spun Aluminium PARCAN Light 3200K with RDM protocol and duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 36V DC COB LED Max Power Consumption upto 100W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : Min 10° to 30° or more manually adjustable zooming • Lens: Lense Dia 150mm ± 5% . • Lens Material: Poly methyl methacrylate without bubbles and crack to provide pleasant light output.. Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz Output : 36V DC power supply. • Power Consumption : 100W ± 15% • Dimming : 0 to 100% 8 Bit Linear Dimming • Lighting Fixture must be provided with Minimum 3 Mtr Length (2.5 Mtr Length Power In Cable + 0.5 Mtr Power out Cable) 3 core 1.0Sq mm FRLS & ISI mark cable with 3pin IEC Male Plug Mandatory. • RDM ID Information: RDM ID Can able to show minimum following Information like * • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Focus type : Smooth focus adjustment from rear with thermoplastic Knob • Focusing Mechanism : Manual Focusing mechanism forsmooth zooming. 8.000 Units 0.00

NS-48 200W LED Fresnel spot Light 3200K with RDM protocol and Extruded aluminium body duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 54V DC COB LED Max Power Consumption upto 200W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : Min 10° to 50° or more manually adjustable step less linear zooming • Fresnel lens: Lense Dia 200mm ± 5% to provide adjustable cone of light that has a soft edge, easily blended with adjacent beams to provide even illumination. • Lens Material: Annealed Fresnel lense made up of high quality, shock resistant borosilicate glass with brand name embossed on the Lense but without bubbles and crack to provide uniform light output. Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz Output : 54V DC power supply. • Driver is comply with IEC/EN 61347-2-13 for safety standard, OEM must be provide test certificate • Power Consumption : 200W ± 15% • Secondary Safety glass fuse of 3 Amps with easy replacement position. • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Focus type : Smooth focus adjustment from rear with thermoplastic Knob • Focusing Mechanism : Focusing mechanism of lights should be SS/Brass lead screw type for step less smooth zooming. 4.000 Units 0.00

NS-49 200W LED profile spot Light 3200K with RDM protocol and Die cast body duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 54V DC COB LED Max Power Consumption upto 200W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System •• Certificates : CE Certificates • LED Lights must be CE certified to ensure required quality & reliability of the producs. Copy of CE Certificates must be submitted along with offer. • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Dimming type : Smooth dimming adjustment from rear with Knob 2.000 Units 0.00

NS-50 400W LED BLINDER Light 3200K with RDM protocol and MS / Aluminium sheet duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 36V DC COB LED Max Power Consumption upto 100W / Piece • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95• Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : 30° • Panel lens: PMMA LENS ARRAY combined with a special optical design produces uniform and pleasant lighting even when used with a mixture of different LEDs • Lens Material: Poly methyl methacrylate without bubbles and crack to provide pleasant light output. Electrical System• Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning 4.000 Units 0.00

NS-51 150W LED HYBRID MOVING Light with RDM protocol and Hi grade plastic body black color - Light Source • LED Lamp: COB LED Max Power Consumption upto 150W • Base Color : Cool White Optical System • Beam Angle: 3°-7° or More • Zoom Angle: 7°-21° or More • PC lens: Lense Dia 100mm ± 10% • Lens Material: Shock resistant borosilicate glass Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz • Power Consumption : 200W ± 15% • Lighting Fixture must be provided with Minimum 3 Mtr Length 3 core 1.0Sq mm FRLS cable with 3pin IEC Male Plug. • Lighting fixture must be properly earthed and earthling cable should be connected with power supply chord. Control System • Control Protocol : RDM & Manual • Easy setup: locally and remotely by RDM protocol - integrated display • LED Lights must be CE certified to ensure required quality & reliability of the products. Copy of CE Certificates must be submitted along with offer. Mechanical System • Pan & Tilt Angle :540° & 240° 16bit electronic movement. • Zoom : Stepless Smooth electronic Zoom • Weight : 9 Kg ~ 12 Kg 1.000 Unit 0.00

NS-52 Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish - Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key. Receptacle - 28mm standard TV spigot. Safety - MS Galvanized chain with pin. Finish - Pretreated and black epoxy polyester powder coated. Self-weight - 0.54Kg Safe working load – 150Kg. 28.000 Units 0.00

NS-53 Safety bond with lock clip -Safety bond with lock clip to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly. SWL 100Kgs. 28.000 Units 0.00

NS-54 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish -Identification name plate round 79MM undergone through 7 Tank chemical treatment to keep them rust free and duly powder coated in matt White texture finish. 27.000 Units 0.00

NS-55 Fixed Stage lightbar 9 Mtrs Length made of dual barren 40NB pipe with black epoxy polyester powder coated - Dual barrel Light bar equipped with 40x75x40 Cable trunking with lid for better aesthetic look and for cable safety. Dual barrel pipe construction welded with 75x6mm MS Flat in every 2 Mtrs for better strength 2.000 Units 0.00

NS-56 Fixed FOH lightbar 12 Mtrs Length made of dual barren 40NB pipe with black epoxy polyester powder coated - Dual barrel Light bar equipped with 40x75x40 Cable trunking with lid for better aesthetic look and for cable safety. Dual barrel pipe construction welded with 75x6mm MS Flat in every 2 Mtrs for better strength 1.000 Unit 0.00

NS-57 Main Valance bar arrangement 12 Mtr Length made up of 40NB MS Pipe with required suspenders duly black epoxy polyester powder coated - Made using 40 NB, 48MM OD, 2mm thickness MS Pipe or higher size • Suitable suspender and clamps made with MS Angle of size 40x40x5 mm thick or higher size • Height adjustable M12 stud of suitable length as per site requirement along with suitable hardware’s with 40 NB pipe coupler clamp if required.• All thematerials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. 1.000 Unit 0.00

NS-58 Motorised Main curtain track 12 Mtrs mechanism arrangement with 1.1 KW 2pole motor and gearbox black epoxy polyester powder coated but without fabrics - Heavy duty aluminium I track of 48X84mm, duly epoxy polyester powder coated in black matt texture finish. Track mounting brackets constructed of C track of dimension 40X50X40mm 1.1KW / 1.5HP Motor, 2 pole, B5 Flange mount motor without DC Brake : Motor Makes Hindustan , Bharat Bijli, Crompton, Kirloskar , RemiGI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center.Curtain holding trollies with ball bearingfor smoother noiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm /250 mm throughout the track. .All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. 1.000 Unit 0.00

NS-59 Fire retardent Velvet fabric with 100% Gathering for Main Valance duly stiched - Velvette fabric must undergone for fire retardant treatment 100% (2 times of the finished dimension) gathering Stitched as per the approved pattern and color GSM not less than 300 Duly stitched along with and eyelets.Size : 35 SQM 1.000 Unit 0.00

NS-60 Fire retardent Velvet fabric with 100% Gathering for Main curtain duly stiched - Velvette fabric must undergone for fire retardant treatment 100% (2 times of the finished dimension) gathering Stitched as per the approved pattern and color GSM not less than 300 Duly stitched along with and eyelets. Size : 82SQM x 2 Pieces 2.000 Units 0.00

NS-61 MS Fabricated 4 way IEC Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures - MS Power junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish CE approved 4 way 10A IEC Socket Fixing : Snap fit /15 (1.5mm), Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C, Moldings : Nylon, Flammability Rating UL94V-0 CE certified FC/PG 11 cable entry gland, Junction Box must be compact of Size : 140 x 112 x 50mm or less Pipe clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing 12.000 Units 0.00

NS-62 powder coated - MS Power junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish CE approved 2 way 10A IEC Socket SPST 4 Pins Toggle Button Rocker switch Fixing : Snap fit /15 (1.5mm), Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C, Moldings : Nylon, Flammability Rating UL94V-0 CE certified FC/PG 11 cable entry gland, Junction Box must be compact of Size : 140 x 112 x 50mm or less Pipe clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing 3.000 Units 0.00

NS-63 MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX OUT (Female plug) of reputed make connector, Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 8.000 Units 0.00

NS-64 MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX male plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX IN (Male plug) of reputed make connector, Extra high temperature resistant insulator material,All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 1.000 Unit 0.00

NS-65 mout plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.1 Nos each of 5 pin XLR DMX IN (Male plug)&5 pin XLR DMX IN (Male plug) of reputed make connector, 0.3 Mtr Length Dmx Cable with Cable mouth 5 Pin XLR Male &Female loop Cable. Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified 2 Nos of FC/PG 7 cable entry gland, Junction Box must be compact of 140 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 1.000 Unit 0.00

NS-66 MS Fabricated Auxilliary marshalling box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated - MS fabricated Auxiliary marshalling boxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. CE certified FC/PG 7 & 11 cable entry gland required Nos as per cable entry. MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors. Box door must be made with Hingeable door with screw lock. Pipe clamp arrangement for fixing 3.000 Units 0.00

NS-67 MS Fabricated Motor Cable Termintion box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated - MS fabricated Motor Cable Terminationboxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. CE certified FC/PG 11&13.5 cable entry gland required Nos as per cable entry. MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection)Box door must be made with Hingeable door with screw lock. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing 1.000 Unit 0.00

NS-68 MS Perforated 75mm Wide Cable Tray with Lid, black epoxy polyester powder coated - MS perforated trays with press fit type tray lid Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement. 100.000 Units 0.00

NS-69 bare copper for internal earthing system - Internal earthing copper bare conductor of size 10 SWG forpower network related to work coming under our scope. 1.000 Unit 0.00

NS-70 Installation hardwares required for the successful execution of work - Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work. 1.000 Unit 0.00

NS-71 coated - Main Incomer 32A TPN. TPN Make: L&T, ABB, Siemens Out Going10A SP MCB’s for Lighting Junction Box Out Going 6A SP MCB’s for Splitter & Console R, Y, B Indicator lamp, CE certified Nylon FC/PG 11 7 & 21 glands for outgoingcables as per requirements 11/8" or Higher size Brass gland for incoming cable MS MCB channel required length for fixingof MCB’s All the MCB's identified by a Name plate with suitable code/Number, All the cables inside the panel routed through gray color cable trough. All the cables used inside the panel should be FRLS PVC Insulated copper multistrand flexible and must have ISI Marking. All the outgoing cables terminated through Grey terminal connector with each line having P, N, E Indication. Panel Including wiring and bus bar connection with proper earthing. Panel with Hingeable door with key door lock complete. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing (Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent 1.000 Unit 0.00

NS-72 SITC of CE Certified RDM Enabled 1 universe 512 channel, 48 Fixture Control DMX Lighting Console for RDM/DMX network with LCD screen for easy navigation - 512 or 1024Channels 48 individual fixture control 3 or more encoder wheels LCD Display Support RDM &Art net 1.000 Unit 0.00

NS-73 SITC of MS Fabricated Combined 1 Way Motor Control Center Panel with Remote control panel for light bars duly epoxy polyester powder coated - 16A TP or TPN Incomer. TP/TPN R, Y, B Indicator Lamp Volt Meter to read the incoming voltage of each phase. Main Contactor of 9A 240V 4 pole contactor with 04 -06A Over Load relay for safety 24V 4 pole Low Voltage Contactors for each motor outgoing 24V 4 pole Low Voltage Master Up & Down Contactors 240V / 24 V Step-down transformer for Low voltage Contactors Terminal Fuse connectors for each output as additional safety. CE certified Nylon FC/PG 13.5 glands for outgoing cables as per requirements 7/8" or Higher size Brass gland for incoming cable connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) Panel Including wiringwith proper earthing. Panel with Hingeable door with 2 Nos key door lock complete. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing 1.000 Unit 0.00

NS-74 SITC of RDM Compatible DMX Splitter with 1 DMX in and optically isolated 8 DMX out port for DMX network - Splitter enclosure made up of MS 18/16 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. Control Protocol RDM and DMX 512 2 DMX input 5 pin XLR Connectors 8 optically isolated DMX output 5 pin XLR Connectors IEC male plug to power supply the splitter LCD Display in the front to check the signal flow 4 Nos of high precision tactile switch for mode selection. Splitter bracket for mounting or 19” rack mount 1.000 Unit 0.00

NS-75 Various Cables & Connectords as per site requirement 1.000 Unit 0.00

High Side Requirement - Group A 0.000 0.00

NS-76 Supply of DAIKIN make Ceiling Suspended Ducted unit with - 200000 BTU/hr Cooling Capacity6600 CFM Air Flow,With scroll Compressor,Microprocessor Based Controller of 16.7 tr Nominal capacity. 2.000 Nos. 0.00

NS-77 Supply of DAIKIN make Ceiling Suspended Ducted unit with - 132000 BTU/hr Cooling Capacity4400 CFM Air Flow,With scroll Compressor,Microprocessor Based Controller of 11.0 tr Nominal capacity. 4.000 Nos. 0.00

NS-78 Daikin 3 Star Inverter Cassette Ac With Wireless 3.0 TON (FCVFQ100AV16) 4.000 Nos. 0.00

NS-79 Daikin 3 Star Inverter Cassette Ac With Wireless 4.0 TON (FCVFQ140AV16) 7.000 Nos. 0.00

NS-80 Installation Installation, testing and commissioning of Ductable Units. 16.7 TR Wired Ductable Unit 2.000 Nos. 0.00

NS-81 11.0 TR Wired Ductable Unit 4.000 Nos. 0.00

NS-82 Supply installation testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per DAIKIN STD. & specifications, all piping inside the room shall be properly supported with MS hanger.( As per Actual Measurement) 100.000 Rmt. 0.00

NS-83 Control Wiring Duct Ac 7C X 2.5 Sq. mm Supply & fixing of control cum transmission wiring of Copper conductor cable along with conduit for looping between indoor & outdoor system & to main Central remote controller system 130.000 RMT 0.00

NS-84 Drain Piping Duct Ac 32 mm dia, 25 mm dia Supply and fixing rigid UPVC piping complete with fittings, supports as per DAIKIN STD. & specifications and duly insulated with nitrile rubber insulation. 50.000 Rmt 0.00

CASSETTE AC 0.000 0 0.00

NS-85 Installation Charge Per Unit for Four way Cassette AC 11.000 pc 0.00

NS-86 Additional Copper Pipe (per Rmt.) for Cassette AC 165.000 Rmt 0.00

NS-87 UPVC Drain pipe with Insulation (per Rmt.) 110.000 Rmt 0.00

NS-88 Communication Wire - 4 Core 1.5 Sqmm Wire ( Per Rmt.) 198.000 Rmt 0.00

NS-89 Communication Wire - 7 Core Wire ( Per Rmt.) RO Rmt

NS-90 Wrapping Tape RO Roll

NS-91 Nitrogen Pressure Testing & Vaccumming for already installed copper pipes RO ft

NS-92 Wall Cutting-Chiseling RO ft

NS-93 ODU Stand As Per Unit Drawing Cassette Ac RO Nos

NS-94 Ducting Supply, Installation, Testing & Commissioning of Site fabricated ducting as per SMACNA tech specifications & drawings complete GI Ducting - 24 Gauge ( .60 mm) 150.000 Sqmt 0.00

NS-95 GI Ducting - 22 Gauge ( .80 mm) 80.000 Sqmt 0.00

NS-96 Acoustic Insulation-9 mm thick Providing and fixing of Duct acoustic lining with glass wool insulation, covered with perforated Aluminium 26 Ga, sheet, nuts, bolts etc. complete with all accessory as required. 80.000 Sqmt 0.00

NS-97 Thermal Insulation -13 mm thick Providing and fixing closed cell crossed linked polyethylene insulation on duct complete with all accessory as required. 150.000 Sqmt 0.00

NS-98 Grilles/Diffusers Supply, Installation and Testing of Supply & Return Air grilles/ diffusers as per specifications and drawings. Powder Coated Extruded Aluminium supply/exhaust air grill as per specs & drawing 100.000 Rmt 0.00

NS-99 Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. 6.000 Nos 0.00

NS-100 Duct Color vcd damper 6.000 Sqmt 0.00

NS-101 Ventilation Cabinat Fan 4500 CFM Installation Installation, testing and commissioning of Ventilation Fan Units. 1.000 Nos 0.00

NS-102 Ducting-GI Ducting - 24 Gauge ( .60 mm) Supply, Installation, Testing & Commissioning of Site fabricated ducting as per SMACNA tech specifications & drawings complete 70.000 Sqmt 0.00

NS-103 Grilles/Diffusers Supply, Installation and Testing of Supply & Return Air grilles/ diffusers as per specifications and drawings. Powder Coated Extruded Aluminium supply/exhaust air grill as per specs & drawing 0.500 Sqmt 0.00

NS-104 Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. 1.000 Nos 0.00

NS-105 Refrigerant R-410 Refrigerant Charging 60.000 Kg 0.00

NS-106 ODU STAND FABRICATION DUCT UNIT ODU Stand As Per Unit Drawing RO Nos

NS-107 KIRLOSKAR, IOT Enable, 1010 kVA DG set with Genset Model- KG1-1010WS & Engine Model DV16ETA, 16-cylinder developing 1210 BHP & coupled with KG-make Alternator Liquid Cooled with Control Panel, Acoustic Enclosure & Base frame having inbuild fuel tank of 990 Ltrs 1.000 Set 0.00

TOTAL (Non Schedule) : Rs.

BIHAR STATE EDUCATIONAL INFRASTRUCTURE DEVELOPMENT CORPORATION LTD. SHIKSHA BHAWAN, SAIDPUR, PATNA

BILL of Quantity for Construction of Auditorium Cum NDA Motivational Hall at Sainik School, Nalanda

Rates are based on BCD SOR 2022 (w.e.f. 01.01.2022) for Civil & BCD SOR 2023 (w.e.f. 01.09.2023) for Electrical Works

Amount of B.O.Q. of Schedule Item (In Rs.) :- 8,52,25,536/- Amount of E.M.D. (In Rs.) :- 22,52,300/-

Cost of B.O.Q. (In Rs.) :- Rs.10,000/-(Ten Thousand) Completion Period :- 15 Months

Part A (Items on Schedule Rate, for which tenderer have to quote rates on % above/below basis)

Sl. No. Item No. Item of Work QTY unit Rate Amount

1 BSR 2.6.1 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. All Kinds of soil 4009.323 cum 314.90 1,262,535.81

2 BSR 2.26 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead 2329.581 cum 123.90 288,635.09

3 BSR 2.25A Excavating, supplyingand fillingof local earth (including royaltybut excludingcairriagecost) bymechanical transport uptoa leadof 3km also including ramming and watering of the earth in layers not exceeding20cmintrenches,plinth,sidesof foundationetc.complete. If localearthisavailableatmorethan3kmleadtheactual leadmust beapprovedbycompitentauthority. cairraiageofmaterialwillbepaid seperately and calculated after deducting initial lead 3221.072 cum 411.70 1,326,115.34

4 BSR 16.78.1 Construction of granular sub-base by providing close graded Material conforming tospecifications,mixing inamechanicalmix plantatOMC,carriageofmixedmaterialbytipperstoworksite, for all leads&lifts, spreading inuniformlayersof specified thickness with motor grader on prepared surface and compacting with vibratorypower roller toachieve thedesireddensity, completeas per specifications and directions of Engineer-in-Charge. 133.000 M3 1,310.40 174,283.20

5 BSR 16.69 Providing and laying at or near ground level factory made ker bstone of M-25 grad ecementconcreteinpositiontotherequiredline, level andcurvature, jointedwithcementmortar1:3(1cement: 3coarse sand), includingmaking jointswithorwithoutgrooves(thicknessof jointsexceptatsharpcurveshallnot tomorethan5mm), including makingdrainageopeningwherever requiredcompleteetc. asper directionofEngineer-in-charge(lengthof finishedkerbedgingshall bemeasured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 42.000 M3 7,998.80 335,949.60

6 BSR 16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 1330.000 M2 778.00 1,034,740.00

7 BSR 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 225.053 cum 287.30 64,657.73

8 BSR 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of E/l, 2234.807 sqm 283.30 633,120.82

9 13.18 15mmcementplaster1:3(1cement:3coarsesand) finishedwitha floatingcoatofneatcementontheroughsideofsingleorhalfbrick wall. 64.800 SQM 229.30 14,858.64

10 BSR 4.1.6 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size) 231.460 cum 3,279.80 759,142.51

11 BSR 4.1.8 Providingand layinginpositioncement concreteof specifiedgrade exluding the cost of centring and shuttering-all work upto plinth level. 1.4.8 (1Cement :4coarsesand :8gradedstoneagregate40mm nominal size) 158.410 cum 2,975.20 471,301.43

12 BSR 4.11 Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size) 199.568 sqm 245.60 49,013.90

13 BSR 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. 128.579 Sqm 436.60 56,137.59

14 BSR 5.1.1 Providingand laying inpositionspecifiedgradeof reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:2 (1 cement:1 coarse sand:2 graded stone aggregate 20mm nominal size) 5.502 cum 5,961.90 32,802.37

15 5.2.1 Reinforced cement concrete work in wall (any thickness), including attachedpilasters,buttresses,plinthandstringcourses, fillets,columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement. 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate 20 mm nominal size) 1.143 cum 6,943.50 7,936.42

16 5.3 Reinforced cement conrete work in beams,suspended floors, roofs havingslopeupto15, landings,balconiec,shelves,chajjas, lintels,bands, plainwindowsills, staircasesandspiral staircasesuptofloor five level excludingthecostofcentring,shuttering, finishingandreinforementwith 1:2:4(1cement:2coarsesand:4gradedstoneaggregate20mmnominal size). 6.316 cum 5,335.90 33,701.54

17 BSR 5.33A.2.2 Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc. 1.140 Cum 5,677.20 6,472.01

18 5.33B.1 Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C 6.316 cum 164.50 1,038.98

19 5.33B.2 Add or deduct for providing richer or leaner mixes respectively at all floor levels. Providing M-30 grade R.C.C. instead of M-20 grade R.C.C. 6.316 cum 164.50 1,038.98

20 5.33.1.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. All works up to plinth level Concrete of M-25 grade with minimum cement content of 330 kg/cum 1129.100 cum 5,063.40 5,717,084.94

21 5.33.2.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. 232.730 cum 5,863.20 1,364,542.54

22 5.33.2.1 Providingandlayinginpositionreadymixedorsitebatcheddesignmix cement concrete for reinforced cement concretework; using coarse aggregateand fine aggregatederived fromnatural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommendedproportionsasperIS:9103toaccelerate/retardsettingof concrete, toimprovedurabilityandworkabilitywithout impairingstrength; includingpumpingof concrete tositeof laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcementasperdirectionof theengineer-in-charge; for thefollowing grades of concrete. Note:Extracementupto10%of theminimumspecifiedcementcontent indesignmixshallbepayableseparately. Incasethecementcontent in designmixismorethan110%of thespecifiedminimumcementcontent, thecontractorshallhavediscretiontoeitherre-designthemixorbearthe cost of extra cement. 431.861 cum 5,863.20 2,532,087.42

23 BSR 5.9.1 Centring and shuttering including strutting,propping etc. and removal of form for. Foundations, footings, bases of columns etc. for mass concrete. 601.368 Sqm 211.60 127,249.47

24 5.9.3 Suspended floors, roots, landings, balcnies and access platform. 2531.679 Sqm 437.50 1,107,609.56

25 5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cms wide 81.419 Mtr 130.20 10,600.75

26 5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers. 2515.064 Sqm 404.70 1,017,846.40

27 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts 1299.758 Sqm 494.40 642,600.36

28 5.9.7 Stairs,(excluding landings) except spiral-staircaces. 162.551 Sqm 439.90 71,506.18

29 5.9.19 Weather shade,Chajjas, corbels etc. including edges 2.340 Sqm 550.90 1,289.11

30 BSR 5.22.7A Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars TMTC-500-8mm dia. 47538.350 Kg 94.50 4,492,374.08

31 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 47000.939 Kg 92.60 4,352,286.95

32 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 47443.701 Kg 90.80 4,307,888.05 27299

33 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-16mrn to 25 mm Dia . 93116.353 Kg 91.70 8,538,769.57 81897

34 BSR 13.17.1 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement 5.524 Sqm 203.60 1,124.69

35 BSR 13.26 Neat cement punning 5.524 Sqm 40.50 223.72

36 BSR 10.18 Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 42.000 Each 165.40 6,946.80

37 BSR 6.1.14A Brick work with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) 763.706 cum 4,819.90 3,680,986.55

38 BSR 6.3A Extra for Brick work in superstructure above plinth level upto floor V cum 617.215 cum 842.20 519,818.47

39 BSR 6.18.4A Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send) 272.401 sqm 599.30 163,249.92

40 BSR 13.11.4 12 mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) 3654.625 Sqm 141.50 517,129.44

41 DSR 13.86A 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In- Charge. 3.780 sqm 157.20 594.22

42 BSR 13.12.2 15 mm cement plaster on rough side of single or half brick wall of mix. 1:4(1 cement: 4 coarse sand ) 3224.228 sqm 176.40 568,753.82

43 BSR 13.24.2 6 mm cement plaster to ceiling of mix : 1:4 (1 cement: 4 coarse sand) 853.805 Sqm 125.60 107,237.91

44 13.73.1 Colour washing such as green, blue or buff to give an even shade New work (two or more coats) with a base coat of white washing 182.020 SQM 25.90 4,714.32

45 BSR 13.80A.1 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 7596.818 sqm 81.10 616,101.94

46 13.94.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary pain+ of approved brand and manufacture 6.048 SQM 116.50 704.59

47 BSR 13.45.1 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm 3224.228 sqm 215.20 693,853.87

48 BSR 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 390.030 sqm 137.00 53,434.11

49 BSR 13.77.2 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer Two or more coats on new work 4208.410 Sqm 102.30 430,520.34

50 BSR 13.93 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work 32.400 sqm 84.50 2,737.80

51 BSR 10.6.1 Supplyingand fixing-rollingshuters of approvedmake.made of required sizeofM.S.Iathsinterlockedtogether throughtheir intirelengthandjointed togetherat theendbyendlocksmountedonspeciallydesignedpipeshaft withbrackets, sideguidesandarragements for insideandoutsidelocking withpushandpull operationcomplete includingthecost of providingand fixingnecessary27.5cmlongwirespringsmanufacturedfromhightensile steelwireofadequatestrengthconformingtoIS:4454-part1andM.S. top cover of required thickness for rolling shutters. 80x1.25mmM.S. Laths with 1.25mm thick top cover. 13.500 sqm 2,673.70 36,094.95

52 BSR 9.1.1 Providing wood work in frames of doors windows,clerestory windowsand other frames,wrought framedand fixed inpositionwithholdfast lugsor with dash fasteners of required dia& length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood 0.950 Cum 120,526.60 114,500.27

53 BSR 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including stainless steel butt hinges with necessary screws 56.700 sqm 2,845.60 161,345.52

54 BSR 9.5.1 Providingand fixingpanelledor panelledandglazedshutters for doors, windowsandclerestorywindows, including ISImarkedM.S.pressedbutt hingesbright finishedof requiredsizewithnecesseryscrews, excluding panellingwhichwillbepaidforseparately,allcompleteasperdirectionof Engineerin-charge. Second Class teak wood 35 mm thick 8.640 sqm 3,169.50 27,384.48

55 BSR 9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelledandglazedshutters for doors,windowsandclerestorywindows (Area of opening for panel inserts excluding portion inside grooves or rebates tobemeasured). Panelling for panelledor panelledandglazed shutters 25 mm to 40 mm thick: Float glass panes. 5.5 mm thick glass pane. 4.320 sqm 1,576.50 6,810.48

56 BSR 13.101.1 French spirit polishing: Two or more coats on works including a coat of wood filler. 150.768 Sqm 215.80 32,535.73

57 BSR 13.104.1 Polishing on wood work with ready made wax polish of approved brand and manufacture: New work 42.018 Sqm 94.60 3,974.90

58 BSR 26.86.6 Providingand fixing factory made single extruded WPC (Wood PolymerComposite)solid door/window/Ceosetorywindows & other Frames/Chowkhat comprising ofvirgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximumtoxicityindexof12for 100gms) fabricatedwithmiter joints after applyingPVC solvent cement and screwed with full body threaded star headedSS screwshavingminimum frame densityof 750kg/cum, screwwithdrawal strengthof 2200N(Face)& 1100N (Edge), minimum compressive strengthof58N/mm, modulus of elasticity900 N/mmand resistancetospread of flame ofClassA category withproperty of beingtermite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SSdash fastenersof required diaand lengthcomplete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately). Note:ForWPCsolid door/windowframes, minus5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation inprofiledimensions onplussideshall beacceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm 99.000 Mtr 1,182.90 117,107.10

59 BSR 26.87.1 Providing and fixing factory made single extruded WPC {Wood Polymer Composite} solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives {maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N {Face) & 900N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In Charge. {Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick 31.500 Sqm 3,866.50 121,794.75

60 BSR 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding 2661.900 Kg 144.50 384,644.55

61 10.3 Providing and fixing in position collapsible steel shutters with vertical channes20x10x2mmandbracedwith flat irondiagonals20x5mmsize withtopandbottomrailofT-tron40x40x6mmwith40mmdiasteelpulleys completewithbots.nuts lockingarrangement stoppers handies including applying a priming coat of approved steel primer. 42.840 Sqm 6,303.40 270,037.66

62 10.5.1 Providingandfixing1mmthickM.S.sheetdoorwithframeof40x40x6mm angle iron and 3mmMSgusset plates at the junction and corners.all necessary fittingscompletejncludingapplyingaprimingcoat of approved steel primer. 24.120 Sqm 3,653.00 88,110.36

63 BSR 13.82.1 Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: 310.276 sqm 83.50 25,908.05

64 BSR 21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) 294.823 Kg 418.40 123,353.94

65 BSR 21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) 443.896 Kg 480.20 213,158.86

66 BSR 21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness(weight not less than 10kg/sqm) 150.960 sqm 809.30 122,171.93

67 BSR 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) 20 to 25 mm thick - 56.325 sqm 1,252.70 70,558.33

68 BSR 11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm 5.240 sqm 1,334.90 6,994.88

69 BSR 11.56.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete asper the architectural drawings with 18 mm thick stone slab over 20 mm (average)thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 320.936 sqm 3,605.20 1,157,038.47

70 BSR 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 424.402 sqm 795.00 337,399.59

71 BSR 11.41A.3.2 Providing and laying Vitrified tiles infloor indifferent sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming toIS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey [email protected] kg/sqm includinggrouting the jointswithwhite cementandmatchingpigmentsetc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will bedone with thenotch trowel, plier, wedge, clips of required thickness, leveling system and rubbermallet for placing the tiles gentlyand easily. Glazed Vitrified tiles Matt/ Antiskid finish of size Size of Tile 600 x 1200 mm 118.760 sqm 1,356.00 161,038.56

72 BSR 11.41A.1.5 Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 664.288 sqm 1,356.00 900,774.53

73 11.33.2 25 mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete . 2nd class Deodar wood 226.500 sqm 2,683.60 607,835.40

74 BSR 8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 7.141 sqm 4,401.20 31,428.97

75 BSR 12.78.2 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 53.700 mtr 257.50 13,827.75

76 BSR 12.79.1.2 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.Coupler - 110mm 13.000 Each 120.00 1,560.00

79 BSR 12.80.2 Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete. 110 mm 19.000 each 182.72 3,471.68

80 BSR 22.9.2 Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd & 4th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS: 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as lOOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat which shall be paid for separately as per DSR Item No. 12.19 32.500 Sqm 393.30 12,782.25

81 BSR 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni). 197.058 Sqm 480.60 94,706.07

82 BSR 22.8.1 Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water-proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge. 1147.992 Sqm 850.70 976,596.79

83 BSR 8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and 8.640 Sqm 3,542.90 30,610.66

84 10.32.1 Steel work welded in built up sections/framed worK including cutting hoisting, rixing inpositionandapplyingaprimingcoat of approvedsteel primer using structural steel, etc. as required. Instringers, treads landingsetc. of stair cases includinguseof required plates wherever required all complete. 4883.328 Kg 104.00 507,866.11

85 BSR 10.2 Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete 52250.000 kg 95.40 4,984,650.00

86 BSR 12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1250.000 sqm 625.10 781,375.00

87 BSR 12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws complete : 55.285 Sqm 396.80 21,937.09

88 12.51.6 Gutter (600 mm over all girth) 92.142 Mtr 898.70 82,808.02

89 BSR 12.57X Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge. 1250.000 Sqm 259.80 324,750.00

90 12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 1506.148 Sqm 993.00 1,495,604.96

91 DSR 26A.1 Providing and supplying aluminium extruded tubular and other aluminiumsectionsasper therchitectural drawingsandapproved shopdrawings, thealuminiumqualityaspergrade6063T5orT6as perBS74,includingsuperdurablepowdercoatingof60-80microns conformingtoAAMA2604ofrequiredcolourandshadeasapproved bytheEngineer-in-Charge. (Theitemincludescostofmaterialsuch ascleats,sleeves,screwsetc.necessaryfor fabricationofextruded aluminium frame work. Nothing extra shall be paid on this account). 952.000 Kg 370.40 352,620.80

92 DSR 26A.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (doubleglazed)visionpanelunitsofsizeandshapeasrequiredand specified,comprisingofanouterheatstrengthenedfloatglass6mm thick, of approvedcolourandshadewithreflectivesoftcoatingonsurface# 2of approvedcolour andshade, an innerHeat strengthnedclear floatglass6mmthick,spacertube12mmwide,dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the requiredperformances, asper theArchitectural drawings, asper theapprovedshopdrawings, asspecifiedandas directedbytheEngineer-in-Charge.TheIGUsshallbeassembledin thefactory/workshopof theglassprocessor. (Payment for fixingof IGU Panels in the curtain glazing is included in cost of item No.26.2)Forpayment,onlytheactualareaofglassonface#1of the glass panels (excluding the areas of the grooves andweather siliconesealant)providedandfixedinposition,shallbemeasuredin sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coatingonface#2,+12mmAirgap+6mmHeatStrengthenedclear Glass of approved make having properties as visible Light transmittance(VLT)of25to35%,Lightreflectioninternal10to15%, light reflection external 10 to 20 %, shading coefficient (0.25 0.28)andUvalueof3.0to3.3W/m2degreeKetc.Thepropertiesof performance glass shall be decided by technical sanctioning authority as per the site requirement. 112.000 Sqm 3,377.50 378,280.00

93 BSR 10.36 Providingand fixingstainlesssteel (Grade304) railingmadeofHollow tubes,channels, platesetc., includingwelding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessarystainlesssteelnutsandboltscomplete, i/cfixingtherailingwith necessaryaccessories&stainless steel dash fasteners , stainlesssteel boltsetc.,of requiredsize,onthetopof theflooror thesideofwaistslab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). 867.366 Kg 546.80 474,275.73

94 BSR 10.20.2 Chequerredprecast cement concrete tiles22mmthickwithmarbie chipsof size6mmin footpath&coutyard jointedwithneat cement slurrymixedwithpigment tomatchtheshadeof tilesincludingrubbing andcleaning tec. Completeon20mmthickbedof cementmortar 1:4(1 cement:4 coarse sand) 72.757 Sqm 953.10 69,344.70

95 BSR 22.24 Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry- shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakage 24.026 Sqm 265.80 6,386.11

96 BSR 22.23.1 Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry- shake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakage 24.420 Sqm 406.20 9,919.40

97 10.32.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 8750.700 Sqm 114.60 1,002,830.22

98 26.91 Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately. 127.725 Sqm 3,081.60 393,597.36

99 MR Providing and fixing factory-made acoustically treated door suitable for auditorium use, consisting of double-leaf / single-leaf door shutter made of 1.2 mm thick GI sheet on both sides, internally filled with high-density rockwool insulation (minimum 48 kg/m³) for effective sound attenuation. The door shall be mounted on a 1.6 mm thick pressed steel door frame, complete with acoustic rubber gaskets, perimeter sealing and drop-down acoustic seal to prevent sound leakage. The door shall achieve a minimum sound reduction rating of Rw 35–40 dB. The door assembly shall be provided with SS heavy-duty hinges, door closer, mortise lock / panic bar (for exit doors) and all necessary hardware. Finish shall be powder coated / laminate / veneer as approved by the client. Installation shall be complete in all respects, including fixing, alignment, testing and commissioning. 24.480 Sqm 19,368.00 474,128.64

100 Supply Caraige of materials 0.000 0 0.00 0.00

Add Extra cost of Material 0.000 0 0.00 0.00

SEIGNIORAGE FEES 0.000 0 0.00 0.00

Plumbing 0.000 0.00 0.00

101 BSR 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 10.000 Each 4,470.90 44,709.00

102 BSR 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 12.000 Each 4,230.00 50,760.00

103 BSR 17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap 21.000 each 2,369.90 49,767.90

104 BSR 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern 12.000 each 3,723.20 44,678.40

105 BSR 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 12.000 each 299.40 3,592.80

106 BSR 17.32.2 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm 21.000 Each 857.00 17,997.00

107 BSR 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 21.000 Each 146.30 3,072.30

108 BSR 12.78.1 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 75 mm diameter 66.000 Metre 162.70 10,738.20

110 BSR 12.79.3.1 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW) Single tee with door 75x75x75mm 12.000 Each 141.60 1,699.20

112 12.79.4.1 Single tee without door-75x75x75mm 12.000 Each 124.20 1,490.40

116 BSR 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chases and making good the walls etc. 15 mm nominal outer dia pipes 132.000 metre 278.20 36,722.40

117 18.8.2 20mm nominal outer dia pipes 132.000 metre 350.80 46,305.60

118 BSR 18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25mm nominal outer dia pipes 176.000 metre 317.30 55,844.80

119 18.7.4 32mm nominal outer dia pipes 176.000 metre 395.20 69,555.20

120 BSR 18.17.1 Providing & fixing gun metal gate valve with C.I. wheel of approved quality, (screwed end) : 25 mm nominal bore 4.000 each 532.30 2,129.20

122 BSR 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 22.000 each 434.20 9,552.40

123 BSR 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore 33.000 Each 594.80 19,628.40

124 BSR 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe 370.000 metre 410.70 151,959.00

125 BSR 24.4.1 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia 30.000 Mtr. 573.10 17,193.00

126 BSR 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in- charge. 5.303 Cum 1,188.90 6,304.74

127 BSR 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 5.303 Cum 1,195.60 6,340.27

128 BSR 24.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. 3.535 Cum 1,195.60 4,226.45

129 BSR 19.30.1.1 Constructing brick masonry chamber forunderground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 18.000 Each 4,266.80 76,802.40

130 BSR 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 4000.000 Ltr 9.70 38,800.00

131 BSR 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2.000 Each 33,603.40 67,206.80

DEEP BORING 0.000 0.00 0.00

132 BSR 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia 120.000 Mtr. 486.80 58,416.00

133 BSR 24.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia 30.500 Mtr. 660.10 20,133.05

134 24.3.5 75 mm nominal size dia 41.800 Mtr. 414.40 17,321.92

135 BSR 24.4.5 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 75 mm nominal size dia 18.300 Mtr. 482.10 8,822.43

136 BSR 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. 5.565 Cum 1,343.20 7,474.91

137 BSR 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. 10.000 Hour 916.80 9,168.00

138 BSR 24.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia 1.000 Each 210.70 210.70

139 BSR 24.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp 1.000 Each 1,531.40 1,531.40

140 BSR 24.15.1 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia 5.000 Each 228.30 1,141.50

141 BSR 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work40 mm nominal outer dia Pipes 50.000 Mtr. 477.60 23,880.00

142 BSR 18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore 1.000 Each 707.30 707.30

Add 6% GST beyond 12% (Multiplying Factor - 1.0536) = B 0.000 0.00 80,616,198.73

ELECTRICAL 0.000 0.00

143 1.3.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.l. box etc as required. Group C 234.000 Point 1,146.00 268,164.00

145 1.4 Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate suitable G.I. box etc. required. 6.000 Point 1,248.00 7,488.00

146 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit along with 1 Nos 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required. 720.000 Meter 309.00 222,480.00

147 1.7.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 2020.000 Meter 201.00 406,020.00

149 1.7.11 4 X6 sq. mm + 1 X 6 sq. mm earth wire 300.000 Meter 660.00 198,000.00

151 1.24.1 Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch 240.000 Each 82.00 19,680.00

152 1.24.4 3 pin, 5/6 amps socket outlet 34.000 Each 112.00 3,808.00

153 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as req u ired. 39.000 Each 358.00 13,962.00

154 1.31 Supplying and fixing suitable size Gl box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. 31.000 Each 414.00 12,834.00

155 1.32 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 31.000 Each 531.00 16,461.00

156 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. 39.000 Each 64.00 2,496.00

157 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. 54.000 Each 80.00 4,320.00

158 1.41 lnstallation, testing and commissioning of pre-wired, flourescent fitting / compact flourescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated. Copper conductor , single core cable and earthing etc. as required. 1.000 Each 134.00 134.00

159 1.45 lnstallation, testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto cm ) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheeL cover on the fan box etc. as reo u ired. 1.000 Each 203.00 203.00

160 2.9.1 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus -bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required, (But without MCB/RCCB/lsolator) 4 way (4 + 12), double door, horizontal type 13.000 Each 4,184.00 54,392.00

161 2.9.3 8 way (4 +24), double door, horizontal type 10.000 Each 6,199.00 61,990.00

162 2.12.1 Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required' 6A to 32 amps, Single pole 13.000 Each 237.00 3,081.00

163 2.16.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amps 10.000 Each 967.00 9,670.00

165 3.2 Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required. 2.000 Each 6,323.00 12,646.00

166 3.7 Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with Gl thimble as required. 80.000 Metre 37.00 2,960.00

167 3.10 Supplying and laying 25 mm X 5 mm copper strip in 40 mm dia G.l. pipe from earth electrode, including connection with brass nut, bolt. spring, washer excavation and refilling etc. as required. 40.000 Metre 1,628.00 65,120.00

168 3.21 Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for eafth electrode to fill up the excavated earth and earth inspection pit etc. as required. 2.000 Set 16,675.00 33,350.00

169 4.2 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.l. tube, having single prong at top, with 85 mm dia 6 mm thick G.l' base plate including holes etc. complete as required. 2.000 Each 416.00 832.00

170 4.4 Jointing copper/ G.l. tape (with another copper/ G ltape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. 2.000 Each 81.00 162.00

171 4.7 Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run) 60.000 Each 102.00 6,120.00

172 4.8 Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run) 60.000 Each 145.00 8,700.00

173 4.12 Providing and fixing testing joint made of 20 mm X 3 mmthick G.l. strip, 125 mm long, with 4 nos. of tlnned G.l. bolts, nuts, chuk nuts and spring washers etc. complete as req uired. 2.000 Each 102.00 204.00

174 5.3 Supplying and fixing 4'X20 watt LED batten with minimum efficacy 100 lm/w in aluminium housing and complete with integrated electronic driver etc directly on walll ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. (For Non-residential building) 43.000 Each 762.00 32,766.00

175 5.14.4 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required. 90 Watt 3.000 Each 5,516.00 16,548.00

176 5.5 Supplying and fixing replaceable compact commercial batten suitable for Double TB LED tube complete with 20 watt LED polycarbonate TB tube with built in driver etc. directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. 24.000 Each 1,232.00 29,568.00

177 5.8.2 Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 15 watt 24.000 Each 1,608.00 38,592.00

179 6.1.5 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required. 12 watt LED Lamp 32.000 Each 239.00 7,648.00

181 7.1.2 Laying of one number PVC insulated and PVC Sheathed/ XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 35 sq.mm. and upto 95 sq.mm 170.000 Mtr. 326.00 55,420.00

182 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.. 39.000 Each 2,482.00 96,798.00

183 8.17.1 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required. 300 mm sweep 12.000 Each 2,572.00 30,864.00

184 Supply, Pg No. - 18 2208 Supplying 3.5 core, 70 Sq.mm XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminum conductor 520.000 mtr 604.90 314,548.00

MAIN PANNEL 0.000 0 0.00 0.00

185 BSR 2018 -8.10.3 Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 40mmx40mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switchgears. 0.000 0.00 0.00

190 2.5.3 200 amp 415 V heavy duty three phase with neutral busbar chamber. 2.000 Nos 12,132.50 24,265.00

191 Supply, Pg-20, 2313 Pilot lamp for indicator, RYB 6.000 Nos 195.73 1,174.38

192 Supply, Pg-20, 2314 Selector switch 6.000 Nos 396.75 2,380.50

193 Supply, Pg-20, 2312 DIGITAL MULTIMETER (3phase ) 2.000 Nos 3,904.02 7,808.04

195 8.12 Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.) 64.000 SQF 2,600.15 166,409.60

LANDSCAPING 0.000 0.00

196 BSR 23.1 Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of/and manure before and after flooding trench with water (encluding cost of imported earth,sludge or manure). 18.000 sqm 44.70 804.60

197 BSR 23.2 Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks will be reduced by 20% for payment). 10.800 cum 143.50 1,549.80

198 BSR 23.3 Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment). 5.400 cum 282.60 1,526.04

199 BSR 23.4.1 Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of l.S. designation 20 mm 5.400 cum 278.90 1,506.06

200 BSR 23.5 Rough dressing the trenched ground including breaking clods 0.180 100sqm 85.90 15.46

201 BSR 23.6 Uprooting weeds form the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. 0.180 100sqm 283.20 50.98

202 BSR 23.7 Fine dressing the ground 0.180 100sqm 208.80 37.58

203 BSR 23.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately). 5.400 cum 30.10 162.54

204 BSR 23.9 Mixing earth and sjudge or manure in porportion specified or directed. 5.400 cum 20.90 112.86

205 BSR 23.10.2 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. 0.180 100sqm 670.80 120.74

206 BSR 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts. 0.180 100sqm 3,418.20 615.28

207 BSR 23.14.2 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2;1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water,dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately): 50.000 each 69.30 3,465.00

208 BSR 23.15.1 Half brick circular tree guard in 50 class designation bricks, internal diameter 1.25 metre and height 1.? metre above ground and 0.20 m below ground bottom two courses laid dry and top three courses in lime mortar 1:2(1 lime putty:2 surkhi) or cement ortar 1:6 (1 cement:6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: 50.000 each 1,647.60 82,380.00

209 BSR 23.19.1.2 Edging with bricks laid dry length wise including excavation, refilling, consolidating with hand packing and spreading neatly susrplus earth within a lead of 50 m: 100.000 Mtr 38.10 3,810.00

210 BSR 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%). flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) 36.000 cum 126.90 4,568.40

211 2.29.1 Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm 10.000 Each 225.05 2,250.50

212 DSR HOR 2.50 Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge 20.000 Per Qtl 610.70 12,214.00

213 DSR HOR 2.38 Topiary cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topiary) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. 20.000 per plant per month 83.95 1,679.00

214 DSR HOR 2.53 Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge 10.000 per plant per month 932.95 9,329.50

215 RCD 11.20 Providing and fixing tree guard 0.60 metre square, 2.00 metre high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm and steel wire3 mm dia welded and fabricated as per design in two halves bolted together 10.000 Each 3,480.30 34,803.00

216 DSR HOR 2.57.1 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) 5.000 Each 7.30 36.50

217 DSR HOR 3.18 Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge. 5.000 Each 157.85 789.25

218 DSR HOR 3.85 Providing and displaying of Schefflera high colour having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. 5.000 Each 41.00 205.00

219 DSR HOR 4.1 Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 43.05 215.25

220 DSR HOR 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. FOR FRENCH GARDEN 5.000 Each 20.00 100.00

221 DSR HOR 7.74 Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge. 5.000 Each 80.00 400.00

222 DSR HOR 6.7 Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 5.000 Each 20.00 100.00

223 DSR HOR 7.76 Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge. 5.000 Each 80.00 400.00

224 DSR HOR 6.2 Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 5.000 Each 20.00 100.00

225 DSR HOR 7.28 Providing and stacking of Ficus benjamina (green) of height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 105.00 525.00

226 DSR HOR 5.12 Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. 5.000 Each 322.90 1,614.50

227 DSR HOR 4.42 Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 32.80 164.00

228 DSR HOR 4.44 Providing and Displaying plants Nasturtium in different colour well developed with fresh & healthy foliage with full bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.. 5.000 Each 54.35 271.75

229 DSR HOR 4.70 Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 5.000 Each 64.60 323.00

230 DSR HOR 8.9 Supply and stacking of plant Cassia biflora of height 60-75 cm. with 4-5 branches in poly bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 55.00 275.00

231 DSR HOR 4.88 Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.. 5.000 Each 46.15 230.75

232 DSR HOR 9.8 Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. 5.000 Each 30.00 150.00

233 DSR HOR 4.91 Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. 5.000 Each 32.80 164.00

234 DSR HOR 7.65 Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge. 5.000 Each 550.00 2,750.00

235 DSR HOR 7.10 Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. 5.000 Each 180.00 900.00

FIRE FIGHT 0.000 0.00 0.00

236 18.7.7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/1S 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 100mm dia 80.000 mtr 2,555.00 204,400.00

243 18.14.7 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 a)mplete with rubber qasket. Gl bolts, nuts, washers etc.as required 100mm dia. 1.000 Each 17,786.00 17,786.00

244 18.15.3 Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of I .6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 MM 1.000 nos 11,144.00 11,144.00

245 18.11.6 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 100mm dia 1.000 nos 8,960.00 8,960.00

246 18.10.1 Supplying and fixing Single headed extemal yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290a) Single Headed (type A) with blank Gunmetal/StainIess Steel and chain as reauired • 6.000 each 7,646.00 45,876.00

247 18.16.1 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe With 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforminq to IS 636 (type-A) as required Gun Metal 6.000 each 5,202.00 31,212.00

248 18.18.1 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe couolinq as required: Gun Metal 6.000 each 2,416.00 14,496.00

249 18.17.1 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle, Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 mtr. 5.000 each 8,675.00 43,375.00

250 18.21.1 Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler 35.000 nos 522.00 18,270.00

251 18.19.1 Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe 1.000 nos 6,742.00 6,742.00

252 18.20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Air Release Valve 25mm 1.000 nos 18,244.00 18,244.00

253 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore 5.000 nos 399.15 1,995.75

B) FIRE PUMPS & PANELS EQUIPMENTS 0.000 0 0.00 0.00

254 18.4.2 Terrace pump 450 lpm, 30 M head (A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting Of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump Of iron body & bronze impeller With stainless steel shaft, confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply With IP55 class Of protection for enclosure, horiziontal foot mounted type with Class-'F insulation, to IS-325. (D) M.S. fabricated common base plate, guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 1.000 set 86,203.00 86,203.00

255 18.5.1 Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated Of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50HzAc Supply with enclosure protection class IP42 as required : 1.000 set 245,730.00 245,730.00

C) FIRE DETECTION SYSTEM 0.000 0 0.00 0.00

256 17.1.9.1 Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, as reauired. 4 Zone 1.000 nos 8,866.00 8,866.00

257 17.2.9 Supplying installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed Tempreature thermistor complete with base as required. 20.000 nos 2,726.00 54,520.00

258 17.1.3 Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. 5.000 nos 474.00 2,370.00

259 17.1.6 Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged a)ver plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. 5.000 nos 557.00 2,785.00

260 17.5.3.1 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm 1000.000 mtrs 54.00 54,000.00

Total = A+B+C+D 85,225,536.14

Rupees Eight Crore Fifty Two Lakh Twenty Five Thousand Five Hundred Thirty Six Only

Part B (Non Schedule Items of Work, for which tenderer have to quote Item wise rate inclusive of all taxes)

Non Schedule Items 0.000 0.00

NS-1 GEM S/F/F Kalinga 3 Core Copper(EC grade) Submersible Flat Cables for Submersible Pumps KalingaR (KALINGA THREE CORE 4 SQMM CABEL) Product ID : 5116877-43377957844 30.000 Mtr. 0.00

NS-2 GEM S/F/F LIDER 2 HP Starters Control Panel for Submersible Pump LIDERR (LIDER[LS-DOL-SPP 2 H.P]DOL-STARTER) Product ID : 5116877-20575423238 1.000 Each 0.00

NS-3 GEM Supplying fitting & fixing crompton 2.2 kiloWatt 30 LPS Three Phase-Submersible Pump Set cromptonR (CROMPTON 2 hp Three Phase-Submersible Pump Set -CROMPTON) Product ID : 5116877-77824849883 1.000 Each 0.00

NS-4 GEM Devraj Mild Steel sheet Double Door with locking arrangment(4) Fire Hose Cabinet, Warranty 1 Year 6.000 each 0.00

FURNITURE 0.000 0.00

NS-5 The seat frame assembly shall be ERW Tube / IS :3074-2005 GRADE 1: 19 mm dia Round Pipe 1.2mm Thickness . The Seat profile shall be developed to help the users to get necessary comfort in popliteal region and ease of use in forward push for the seat sliding feature.Seat size shall be: 40.5 cm. (W) x 49 cm (D) x 12.5 cm (T)(Front) & 8 cm(T)(Rear). The backrest assembly shall be made of ERW Tube / IS :3074-2005 GRADE 1: 16 mm dia Round Pipe 1.63 mm Thickness & Extra Reinforcement 16 dia round pipe 1.2 mm. The back foam shall be designed with contoured lumbar support for extra comfort at upright and tilted conditions. The back shall be: 47 cm. (W) x 82.3 cm (H) x 11.0 cm (T)(Front) & 6cm (T)(Rear). The Automotive grade HR polyurethane foam for Seat and Back shall be moulded with Density = 55 +/- 5kgs/cu.m. as per JIS K 6401 with compression max 13%. The back & seat covers are made of injection moulded thermoform PPCP as per IS: 10915-1984 with 45.7 cm(W)x 75.5 cm(H)x 2.3mm(T) for back and 43.5 cm(W)x 55.2 cm(D)x 2.3mm(T) for seat. The armrest shall be made up of Polyurathane/wood with waterfall edge design. The armrest shall be available with Polypropelene Cupholder . For Push Back mechanism – Coil Spring / Spring Steel IS : 4454 1981 GRADE 2. The fluimatic slider travels upto 60mm with metal ball and roller cage which results in PUSH BACK OF 140 + 10mm . Should have flexibility to restrict movement of the pushback and slider as per availability of aisle space. The mechanism houses the seat & back and shall has a special feature of upright resistance lock to avoid activation of sliding feature unless enough force shall be applied by user when tilting shall be required. For Auto Tip-up – Torsion Spring / Spring Steel IS : 4454 1981 GRADE 2 (part i). The chair shall rests on the ground on two Side wing frame with plywood with upholstery. Each Leg is a rectangular tube of cross section 50mm X25mm x1.63mm Thickness as per IS:4923-1985 standards . The side panel frame is made of HRPO sheet metal as per IS :1079 -1994 standards alongwith fabric upholstered plywood. It shall be grouted to the floor using 2 nos. anchors for each panel through the base plate. All steel components shall be zinc passivated and powder coated (DFT 40-60 microns). The heavy duty 100 % polyester dyed yarn with 3mm + 0.5mm foam backing fabric is available in shades as per Wipro Box Office shade card. FR grade material confirms to IS 15061. The auditorium chair shall be designed to get mounted/grouted on floors with concrete(min 100 mm) or wooden flooring(min 50 mm) with specific grouting bolts. Provision for lights on sides for seats along the aisles using PP housing with 12mm watt lamp. Aluminum cut-outs available for row & seat numbering. Overall Dimensions shall be Seat Height - 45 cm, Height - 104 +/- 1 cm,min armrest c/c - 53.3 cm, Width & Depth as measured from base - Width-66.0 cm and Folded Depth-66.0 cm, Normal depth-76cm, Extended depth- 92 cm. Dimensions tolerance / variations shall be within +/- 1 cm. 750.000 Each 0.00

NS-6 Supply and installation of Carpet, Loop pile, Gauge 1/10, height 6mm, pile weight 550-600 gm/sqm, roll width 2M to be installed in floor with adhisive, to be complete in all respect as per direction of engineer in charge. 832.000 Sqm 0.00

NS-7 Supply Installation Testing & Commissioning of Dom ip camera 2 MP 120db WDR.3D-DNR, day night (ICR) ROI, Defog, AWB,AGC, BLC HLC ,1/2.7" 2 MP PS CMOS Image sensor, Max 25/30fps @1080 P ,H .265+/H.265 dual sream endcoding,2.8 mm fixed lens (3.6mm optional), IP67, support PoE, Support mobile software ,CMS software' etc as required Make-CP PLUS 28.000 Each 0.00

NS-8 Supply Installation Testing & Commissioning of Network rack 4U for CCTV survilacne device with complete accessoreis, 1 PDU with 6nos of 5A socket 15 AMP Switch, Fan, wire manager of Netrack make etc asrequired. 1.000 Each 0.00

NS-9 Supplying and drawing of UTP 4 Pair CAT-6 LAN cable in the existing surface / recessed PVC concuit etc. as required. 915.000 m 0.00

NS-10 Supply Installation Testing & Commissioning of Network Vedio Recorder up to 32 IP camera input, spport 4SATA TB Hard Disk up to 24 TB , 2 USB .Max 200 Mbps incoming bandwidth, VGA, HDMI simultaneous vidio outputs, H.265, H.264 dual codec decoding , up to 8 Mp resulution preview and play back,ONVIF Version 2.4 conformane support mobile software and CMS software etc as required (Make -CP PLUS) 2.000 Each 0.00

NS-11 Supply Installation Testing & Commissioning of 4 TB Seagate Window surveillance Hard Disk etc as required 2.000 Each 0.00

NS-12 Supply installation testing & commissioning of Network Switch 24 port Poe manged gigabyt 24 # 10/100/1000 Base-T auto-sensing PoE+ ports. 2 dedicated 100/1000 Base-X Fiber SFP ports. Bandwidth: 52 Gbps non-blocking. MAC Address database size: 8,000 media access control (MAC) addresses. Max power (worst case, all ports used, full PoE, line-rate traffic) (Watts): 228.53 W. Make - Netgear, cp-plus,) 5.000 Each 0.00

NS-13 Supply installation testing & Commissioning of 43" Display for CCTV live View & Recording . Screen Size-43" or Higher . Monitor Type-LED. Panel Technology-IPS. Native Resolution-1,920 x 1,080 (Full HD). Brightness-350cd/m2 or higher. Contrast Ratio-1,100 : 1 or higher. Inputs HDMI, DVI-D, RGB, Stereo Mini Jack, USB. Outputs Stereo Mini Jack, External Speaker Out. External Control-RS232C (In/Out), RJ45, IR Receiver. Make - Lg, Sony, Samsung 1.000 Each 0.00

NS-14 Supply Installation Testing & Commissioning of DIGISOL RJ45 CONNECTOR 2.000 Each 0.00

NS-15 Supply Installation Testing & Commissioning of Electric Wire Anchor 3.000 rol 0.00

ACCOUSTIC 0.000 0.00

NS-16 Providing and fixing, in position concealed G.I. section for wall panelling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm., Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200 mm C/C, all complete as per the drawing & directions of engineer-in-charge., The joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish. Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength of 225 kg/sqcm. 840.750 sqm 0.00

NS-17 Anutone Strand 1 Melange 600x1200x20mm, Square EdgeSupply and Installation of Anutone Strand 1 Melange, square edge, magnesite bonded 1mm wide pinewood fibre core tiles,GreenPro certified, of size 600x1200x20mm, volume density 400kgs/m3, weight 8kg/m2 installed by using Anutone Strut framework system and Strut Z-Bars. "The Strut framework systems includes Anutone Strut CC22 thickness 0.50mm, length 3600mm, knurled web 40mm, depth 22mm and equal flanges 13mm is fastened to wall positioned horizontally in a regular manner at 600mm centres. Anutone Strut H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Strut CC22 at 600mm centers. The Strand 1 primer, Kerfed long edge panels shall then be inserted into the Strut H-Spline along their long edges of 2400mm to perfect fit with staggered short edges." 642.404 sqm 0.00

NS-18 Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 118.000 Each 0.00

NS-18 GEM fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B 5.000 nos 0.00

NS-19 GEM Ecofire Portable Fire Extinguishers as per IS 15683 (2018) Low Pressure Extinguisher (Service Pressure ≤19 bar) Powder Based (as per IS 4308 ) Class -A 20.000 nos 0.00

NS-20 GEM PALEX 10 liter GALVANIZED MILD STEEL FIRE BUCKET (Fire suppression hand tools) PALEX (FBSTAND10LTR) 1.000 nos 0.00

AUDIO VISUAL 0.000 0.00

NS-21 90° x 50° Coverage for broad, even sound distribution,2265H 15-inch 2 Way Differential Drive® LF Driver for deep, powerful bass, 2432H HF Compression Driver with 75mm (3") voice coil for crystal-clear highs, Large PT™ Progressive Transition Waveguide for accurate pattern control Rotatable waveguide for vertical or horizontal installation, Bi-Amp/Passive Switchable for flexible operation, FIR Tuning for Frequency & Phase Optimization, Heavy-Duty Birch Plywood Enclosure for durability 4.000 Units 0.00

NS-22 Custom Array Frame 4.000 Units 0.00

NS-23 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

Main Subwoofer 0.000 0.00

NS-24 Dual 18-inch SVG drivers with 4-inch voice coils , Large vent area for high output with low distortion , Switchable parallel/discrete input modes , Durable 11-ply Finnish birch plywood enclosure , 12 M10 threaded suspension points for mounting Transducer Power Rating (AES) , 2400 W (9600 W peak), System Power Rating , Maximum SPL (1m) 30 Hz – 100 Hz: 136 dB-SPL cont avg (142 dB peak)100 Hz – 500 Hz: 136 dB-SPL cont avg (142 dB peak) , System Sensitivity (1w @ 1m) 30 Hz – 100 Hz: 102 dB 100 Hz – 500 Hz: 102 dB 2.000 Units 0.00

NS-25 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

NS-26 Back Fills Ultra compact enclosure , 6.5 in LF transducer , 90° x 90° Progressive Transition™ waveguide with a (1 in) exit compression driver Dual Neutrik NL4 connectors plus screw terminals Frequency Range (-10 dB): 55 Hz - 20 kHz Frequency Response (+/-3 dB): 65 Hz - 18 kHz Directivity Factor (Q): 7 (avg. 500 Hz - 16 kHz) Long-Term System Power Rating3: (Continuous/Program/Peak): 160 W / 320 W / 640 W 10.000 Units 0.00

NS-27 4-channel, 1250W per channel networkable power amplifier for professional installations, featuring DriveCore technology, advanced DSP (EQ, limiters, delay), HiQnet/Audio Architect control, and support for both low-Z (2-16 Ohm) and high-Z (70V/100V) loads without external transformers, with options for BLU Link or Dante/AES67 (DA model). Key specs include 1250W/Ch @ 4Ω, 2500W bridged, ±0.25dB freq response, 0.35% THD, efficient cooling, and universal power. 1.000 Unit 0.00

NS-28 Stage Monitors Powered: Yes , LF Driver Size:12″ woofer , HF Driver Size:1.5″ Neodymium , Total Power:2000W Peak, 1000W RMS , Inputs:2 x XLR-1/4″ combo, 1 x 1/8″ , Outputs:2 x XLR (thru). 1 x XLR (mix out) ,\Frequency Range:50Hz-20khz (-10 dB) , Crossover Frequency:2050Hz , Maximum Peak SPL:132dB SPL , Horizontal Coverage Angle:90° , Vertical Coverage Angle:50° 3.000 Units 0.00

NS-29 a 2-channel audio device for eliminating feedback in live sound, featuring 24 filters/channel, 24-bit/48kHz conversion, XLR/TRS I/O, Type IV Conversion, Wizard setup function, and a full LCD display, offering professional audio control with dynamic range>> and low THD. Specifications include +20dBu max output, 113dB A/D dynamic range, 0.003% THD 1.000 Unit 0.00

NS-30 Signal Processing 12x8 (12 analog inputs, 8 analog outputs) digital signal processor (DSP) in the Soundweb London family, featuring configurable processing, a 48-channel low-latency digital audio bus (BLU link), 12 control inputs, and 6 logic outputs for GPIO integration, all in a 1RU chassis, ideal for tailored audio systems in commercial venues. It uses standard Cat5e for the BLU link, supports remote control via HiQnet Audio Architect, and offers phantom power per channel 1.000 Unit 0.00

NS-31 The BSS BLU-BOB2 is a 1RU rack-mount break-out box with 8 analog audio outputs, expanding the Soundweb London network with low-latency, fault-tolerant BLU-Link digital audio, configured via rear DIP switches for 8-channel blocks from the 256-channel bus, featuring Phoenix connectors for audio/power, 12V DC power, and <0.01% THD performance. Audio Outputs: 8 electronically balanced line outputs on Phoenix/Combicon connectors. Digital Audio Bus: 256-channel, low-latency, fault-tolerant BLU-Link (via RJ45). Configuration: DIP switches for channel range selection 1.000 Unit 0.00

NS-32 32 Mic Inputs 8 XLR/1/4" Combi-jacks for line inputs and instruments 40 DSP input channels (32 mono inputs and 4 stereo channels/returns) 31 Output busses (All with full DSP processing and GEQ) 4-band Fully Parametric EQ on each channel and bus 1.000 Unit 0.00

NS-33 RJ45/Cat5 connectivity, for 100M runs between stage and mixing console (328 feet) 32 remote controlled mic preamps and AD converters 12 XLR analog line level outputs 3U Rack mount design 1.000 Unit 0.00

NS-34 Microphone Wired Vocal Microphone Frequency response tailored for vocals, with brightened midrange and bass rolloff Uniform cardioid pickup pattern isolates the main sound source and minimizes background noise Pneumatic shock-mount system cuts down handling noise 2.000 Units 0.00

NS-35 Wired Instrument Microphone The Shure Beta 57A is a dynamic instrument microphone with a supercardioid polar pattern, offering a tailored 50Hz-16kHz frequency response, 150-ohm impedance, and a rugged build for live and studio use, providing superior rejection of off-axis sound and high gain-before-feedback for instruments like guitars, drums, and brass. 2.000 Units 0.00

NS-36 Wireless Handheld Microphone SVX4 Diversity Receiver. SVX2 Handheld Microphone Transmitter with PG58 Microphone. Frequency Response 60 Hz - 15 KHz. Customized frequency response is smooth and extended. It is specifically tuned for audio use. Cardioid detection pattern rejects off-axis sounds and provides good front feedback. The dynamic cartridge has a simple, solid coil so it can handle high sound levels without any distraction. The steel tennis ball has a "pop" filter grille to reduce breathing noise and wind noise. 2.000 Units 0.00

NS-37 Wireless Lavalier Microphone professional subminiature cardioid lavalier microphone known for its small size, durable Kevlar- reinforced cable, and CommShield® technology, offering wide frequency response (20Hz-20kHz) for natural voice reproduction, with versions available 2.000 Units 0.00

NS-38 Accessories 24-Port Gigabit Unmanaged PoE+ Switch with a 380W power budget, offering 24 Gigabit Ethernet ports (24 PoE+) supporting up to 30W per port for IP cameras, VoIP phones, and APs, with plug-and-play setup, fanless silent operation, rack/desktop mounting, and Energy-Efficient Ethernet (EEE) 1.000 Unit 0.00

NS-39 Speaker Cables 1500.000 Mtr 0.00

NS-40 42U Equipment Rack 1.000 Unit 0.00

NS-41 Connector & Other Accessories 1.000 Lot 0.00

NS-42 Projector-7000 Lumens Smart 4K UHD HDR Laser Projector All-around Projector for Versatile Fields Laser 4K UHD & 3M:1 CR Exceptional Picture Quality With 8.3 mega pixels utilizing 4K UHD (3840 x 2160) resolution, crisp details from 40 to 300-inch screens. With 3M:1 contrast ratio, it can express deep darkness and brightness. 7,000 ANSI Lumens Brightness Great Color Even in Bright Laser (up to 20,000 hours) throw Ratio 1.53 to 2.45 Keystone 25-Point Keystone Adjustment (auto) Lens Shift H: +/- 28%, V: +60%/-33% (auto) Noise 31dB to 35dB Aspect Ratio 16:9Zoom 1.6x (auto) Screen Size - upto 300” HDR yes Connection Terminals HDMI 2.0 in (x3), HDMI out (x1) , DisplayPort (x1), USB Type-A 2.0 (x2), RJ45 (x2), HDBaseT, RS-232c (in/out), IR (in), Audio 3.5mm (in) 1.000 Unit 0.00

NS-43 275 inch Diagonal Projector Screen with 16:9 Aspect Ratio Mounting Method: Wall, Material: HD Matt White Fiber Glass, Color: White, Projection For Which Designed: Projector, Foldability: Inflateble 1.000 Unit 0.00

NS-44 HDMI Cables & Connectors and additional accessories 1.000 OEM 0.00

NS-45 Low Noise Motorized Projector ceiling Lift 1.000 Unit 0.00

NS-46 matt texture finish - Light Source • LED Lamp: 3V DC SMD LED ARRAY • Base color : RGBW • LED Configuration : 12Red, 18Green, 18Blue, 6White Optical System • Light Beam Angle : 15° or 25° • Panel lens: PMMA LENS ARRAY combined with a special optical design produces uniform and pleasant lighting even when used with a mixture of different LEDs • Power Supply Unit, Input: AC 100 - 260V 50/60Hz Output: 24V DC, electronic flicker-free power supply. • Lighting Fixture must be provided with Minimum 3 Mtr Length (2.5 Mtr Length Power In Cable + 0.5 Mtr Power out Cable) 3 core 1.0Sq mm FRLS & ISI mark cable with 3pin IEC Male Plug Mandatory. • Lighting fixture must be properly earthed and earthling cable should be connected with power supply chord. Control System • Control Protocol : RDM & Manual • Mandatory Accessories supplied along with Lighting Fixtures 1) Spud 28 mm Spigot with M12 thread •Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning 8.000 Units 0.00

NS-47 SITC of CE Certified 100W LED Spun Aluminium PARCAN Light 3200K with RDM protocol and duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 36V DC COB LED Max Power Consumption upto 100W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : Min 10° to 30° or more manually adjustable zooming • Lens: Lense Dia 150mm ± 5% . • Lens Material: Poly methyl methacrylate without bubbles and crack to provide pleasant light output.. Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz Output : 36V DC power supply. • Power Consumption : 100W ± 15% • Dimming : 0 to 100% 8 Bit Linear Dimming • Lighting Fixture must be provided with Minimum 3 Mtr Length (2.5 Mtr Length Power In Cable + 0.5 Mtr Power out Cable) 3 core 1.0Sq mm FRLS & ISI mark cable with 3pin IEC Male Plug Mandatory. • RDM ID Information: RDM ID Can able to show minimum following Information like * • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Focus type : Smooth focus adjustment from rear with thermoplastic Knob • Focusing Mechanism : Manual Focusing mechanism forsmooth zooming. 8.000 Units 0.00

NS-48 200W LED Fresnel spot Light 3200K with RDM protocol and Extruded aluminium body duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 54V DC COB LED Max Power Consumption upto 200W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : Min 10° to 50° or more manually adjustable step less linear zooming • Fresnel lens: Lense Dia 200mm ± 5% to provide adjustable cone of light that has a soft edge, easily blended with adjacent beams to provide even illumination. • Lens Material: Annealed Fresnel lense made up of high quality, shock resistant borosilicate glass with brand name embossed on the Lense but without bubbles and crack to provide uniform light output. Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz Output : 54V DC power supply. • Driver is comply with IEC/EN 61347-2-13 for safety standard, OEM must be provide test certificate • Power Consumption : 200W ± 15% • Secondary Safety glass fuse of 3 Amps with easy replacement position. • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Focus type : Smooth focus adjustment from rear with thermoplastic Knob • Focusing Mechanism : Focusing mechanism of lights should be SS/Brass lead screw type for step less smooth zooming. 4.000 Units 0.00

NS-49 200W LED profile spot Light 3200K with RDM protocol and Die cast body duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 54V DC COB LED Max Power Consumption upto 200W • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95 • Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System •• Certificates : CE Certificates • LED Lights must be CE certified to ensure required quality & reliability of the producs. Copy of CE Certificates must be submitted along with offer. • Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning • Dimming type : Smooth dimming adjustment from rear with Knob 2.000 Units 0.00

NS-50 400W LED BLINDER Light 3200K with RDM protocol and MS / Aluminium sheet duly epoxy polyester powder coated in black matt texture finish - Light Source • LED Lamp: 36V DC COB LED Max Power Consumption upto 100W / Piece • Correlated color temperature (CCT) : 3200K ± 200K • Color Rendering Index (CRI): > 95 • Television Lighting Consistency Index (TLCI): > 95 • R9 Value: > 95• Lamp life hour : L70 >50000 Hours @ 55°C • LM 80 Certificate of LED Chip along with lighting fixture must be submitted by the OEM to ensure the light source compatibility with required specification as mentioned above. Optical System • Light Beam Angle : 30° • Panel lens: PMMA LENS ARRAY combined with a special optical design produces uniform and pleasant lighting even when used with a mixture of different LEDs • Lens Material: Poly methyl methacrylate without bubbles and crack to provide pleasant light output. Electrical System• Make and Model : As per RDM ID information Mechanical System • Pan & Tilt Angle : 360° & 270° for rapid repositioning 4.000 Units 0.00

NS-51 150W LED HYBRID MOVING Light with RDM protocol and Hi grade plastic body black color - Light Source • LED Lamp: COB LED Max Power Consumption upto 150W • Base Color : Cool White Optical System • Beam Angle: 3°-7° or More • Zoom Angle: 7°-21° or More • PC lens: Lense Dia 100mm ± 10% • Lens Material: Shock resistant borosilicate glass Electrical System • Power Supply Unit, Input : AC 100 - 260V 50/60Hz • Power Consumption : 200W ± 15% • Lighting Fixture must be provided with Minimum 3 Mtr Length 3 core 1.0Sq mm FRLS cable with 3pin IEC Male Plug. • Lighting fixture must be properly earthed and earthling cable should be connected with power supply chord. Control System • Control Protocol : RDM & Manual • Easy setup: locally and remotely by RDM protocol - integrated display • LED Lights must be CE certified to ensure required quality & reliability of the products. Copy of CE Certificates must be submitted along with offer. Mechanical System • Pan & Tilt Angle :540° & 240° 16bit electronic movement. • Zoom : Stepless Smooth electronic Zoom • Weight : 9 Kg ~ 12 Kg 1.000 Unit 0.00

NS-52 Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish - Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key. Receptacle - 28mm standard TV spigot. Safety - MS Galvanized chain with pin. Finish - Pretreated and black epoxy polyester powder coated. Self-weight - 0.54Kg Safe working load – 150Kg. 28.000 Units 0.00

NS-53 Safety bond with lock clip -Safety bond with lock clip to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly. SWL 100Kgs. 28.000 Units 0.00

NS-54 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish -Identification name plate round 79MM undergone through 7 Tank chemical treatment to keep them rust free and duly powder coated in matt White texture finish. 27.000 Units 0.00

NS-55 Fixed Stage lightbar 9 Mtrs Length made of dual barren 40NB pipe with black epoxy polyester powder coated - Dual barrel Light bar equipped with 40x75x40 Cable trunking with lid for better aesthetic look and for cable safety. Dual barrel pipe construction welded with 75x6mm MS Flat in every 2 Mtrs for better strength 2.000 Units 0.00

NS-56 Fixed FOH lightbar 12 Mtrs Length made of dual barren 40NB pipe with black epoxy polyester powder coated - Dual barrel Light bar equipped with 40x75x40 Cable trunking with lid for better aesthetic look and for cable safety. Dual barrel pipe construction welded with 75x6mm MS Flat in every 2 Mtrs for better strength 1.000 Unit 0.00

NS-57 Main Valance bar arrangement 12 Mtr Length made up of 40NB MS Pipe with required suspenders duly black epoxy polyester powder coated - Made using 40 NB, 48MM OD, 2mm thickness MS Pipe or higher size • Suitable suspender and clamps made with MS Angle of size 40x40x5 mm thick or higher size • Height adjustable M12 stud of suitable length as per site requirement along with suitable hardware’s with 40 NB pipe coupler clamp if required.• All thematerials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. 1.000 Unit 0.00

NS-58 Motorised Main curtain track 12 Mtrs mechanism arrangement with 1.1 KW 2pole motor and gearbox black epoxy polyester powder coated but without fabrics - Heavy duty aluminium I track of 48X84mm, duly epoxy polyester powder coated in black matt texture finish. Track mounting brackets constructed of C track of dimension 40X50X40mm 1.1KW / 1.5HP Motor, 2 pole, B5 Flange mount motor without DC Brake : Motor Makes Hindustan , Bharat Bijli, Crompton, Kirloskar , RemiGI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center.Curtain holding trollies with ball bearingfor smoother noiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm /250 mm throughout the track. .All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. 1.000 Unit 0.00

NS-59 Fire retardent Velvet fabric with 100% Gathering for Main Valance duly stiched - Velvette fabric must undergone for fire retardant treatment 100% (2 times of the finished dimension) gathering Stitched as per the approved pattern and color GSM not less than 300 Duly stitched along with and eyelets.Size : 35 SQM 1.000 Unit 0.00

NS-60 Fire retardent Velvet fabric with 100% Gathering for Main curtain duly stiched - Velvette fabric must undergone for fire retardant treatment 100% (2 times of the finished dimension) gathering Stitched as per the approved pattern and color GSM not less than 300 Duly stitched along with and eyelets. Size : 82SQM x 2 Pieces 2.000 Units 0.00

NS-61 MS Fabricated 4 way IEC Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures - MS Power junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish CE approved 4 way 10A IEC Socket Fixing : Snap fit /15 (1.5mm), Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C, Moldings : Nylon, Flammability Rating UL94V-0 CE certified FC/PG 11 cable entry gland, Junction Box must be compact of Size : 140 x 112 x 50mm or less Pipe clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing 12.000 Units 0.00

NS-62 powder coated - MS Power junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish CE approved 2 way 10A IEC Socket SPST 4 Pins Toggle Button Rocker switch Fixing : Snap fit /15 (1.5mm), Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C, Moldings : Nylon, Flammability Rating UL94V-0 CE certified FC/PG 11 cable entry gland, Junction Box must be compact of Size : 140 x 112 x 50mm or less Pipe clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing 3.000 Units 0.00

NS-63 MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX OUT (Female plug) of reputed make connector, Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 8.000 Units 0.00

NS-64 MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX male plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX IN (Male plug) of reputed make connector, Extra high temperature resistant insulator material,All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 1.000 Unit 0.00

NS-65 mout plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.1 Nos each of 5 pin XLR DMX IN (Male plug)&5 pin XLR DMX IN (Male plug) of reputed make connector, 0.3 Mtr Length Dmx Cable with Cable mouth 5 Pin XLR Male &Female loop Cable. Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified 2 Nos of FC/PG 7 cable entry gland, Junction Box must be compact of 140 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing 1.000 Unit 0.00

NS-66 MS Fabricated Auxilliary marshalling box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated - MS fabricated Auxiliary marshalling boxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. CE certified FC/PG 7 & 11 cable entry gland required Nos as per cable entry. MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors. Box door must be made with Hingeable door with screw lock. Pipe clamp arrangement for fixing 3.000 Units 0.00

NS-67 MS Fabricated Motor Cable Termintion box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated - MS fabricated Motor Cable Terminationboxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. CE certified FC/PG 11&13.5 cable entry gland required Nos as per cable entry. MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection)Box door must be made with Hingeable door with screw lock. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing 1.000 Unit 0.00

NS-68 MS Perforated 75mm Wide Cable Tray with Lid, black epoxy polyester powder coated - MS perforated trays with press fit type tray lid Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement. 100.000 Units 0.00

NS-69 bare copper for internal earthing system - Internal earthing copper bare conductor of size 10 SWG forpower network related to work coming under our scope. 1.000 Unit 0.00

NS-70 Installation hardwares required for the successful execution of work - Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work. 1.000 Unit 0.00

NS-71 coated - Main Incomer 32A TPN. TPN Make: L&T, ABB, Siemens Out Going10A SP MCB’s for Lighting Junction Box Out Going 6A SP MCB’s for Splitter & Console R, Y, B Indicator lamp, CE certified Nylon FC/PG 11 7 & 21 glands for outgoingcables as per requirements 11/8" or Higher size Brass gland for incoming cable MS MCB channel required length for fixingof MCB’s All the MCB's identified by a Name plate with suitable code/Number, All the cables inside the panel routed through gray color cable trough. All the cables used inside the panel should be FRLS PVC Insulated copper multistrand flexible and must have ISI Marking. All the outgoing cables terminated through Grey terminal connector with each line having P, N, E Indication. Panel Including wiring and bus bar connection with proper earthing. Panel with Hingeable door with key door lock complete. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing (Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent 1.000 Unit 0.00

NS-72 SITC of CE Certified RDM Enabled 1 universe 512 channel, 48 Fixture Control DMX Lighting Console for RDM/DMX network with LCD screen for easy navigation - 512 or 1024Channels 48 individual fixture control 3 or more encoder wheels LCD Display Support RDM &Art net 1.000 Unit 0.00

NS-73 SITC of MS Fabricated Combined 1 Way Motor Control Center Panel with Remote control panel for light bars duly epoxy polyester powder coated - 16A TP or TPN Incomer. TP/TPN R, Y, B Indicator Lamp Volt Meter to read the incoming voltage of each phase. Main Contactor of 9A 240V 4 pole contactor with 04 -06A Over Load relay for safety 24V 4 pole Low Voltage Contactors for each motor outgoing 24V 4 pole Low Voltage Master Up & Down Contactors 240V / 24 V Step-down transformer for Low voltage Contactors Terminal Fuse connectors for each output as additional safety. CE certified Nylon FC/PG 13.5 glands for outgoing cables as per requirements 7/8" or Higher size Brass gland for incoming cable connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) Panel Including wiringwith proper earthing. Panel with Hingeable door with 2 Nos key door lock complete. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing 1.000 Unit 0.00

NS-74 SITC of RDM Compatible DMX Splitter with 1 DMX in and optically isolated 8 DMX out port for DMX network - Splitter enclosure made up of MS 18/16 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. Control Protocol RDM and DMX 512 2 DMX input 5 pin XLR Connectors 8 optically isolated DMX output 5 pin XLR Connectors IEC male plug to power supply the splitter LCD Display in the front to check the signal flow 4 Nos of high precision tactile switch for mode selection. Splitter bracket for mounting or 19” rack mount 1.000 Unit 0.00

NS-75 Various Cables & Connectords as per site requirement 1.000 Unit 0.00

High Side Requirement - Group A 0.000 0.00

NS-76 Supply of DAIKIN make Ceiling Suspended Ducted unit with - 200000 BTU/hr Cooling Capacity6600 CFM Air Flow,With scroll Compressor,Microprocessor Based Controller of 16.7 tr Nominal capacity. 2.000 Nos. 0.00

NS-77 Supply of DAIKIN make Ceiling Suspended Ducted unit with - 132000 BTU/hr Cooling Capacity4400 CFM Air Flow,With scroll Compressor,Microprocessor Based Controller of 11.0 tr Nominal capacity. 4.000 Nos. 0.00

NS-78 Daikin 3 Star Inverter Cassette Ac With Wireless 3.0 TON (FCVFQ100AV16) 4.000 Nos. 0.00

NS-79 Daikin 3 Star Inverter Cassette Ac With Wireless 4.0 TON (FCVFQ140AV16) 7.000 Nos. 0.00

NS-80 Installation Installation, testing and commissioning of Ductable Units. 16.7 TR Wired Ductable Unit 2.000 Nos. 0.00

NS-81 11.0 TR Wired Ductable Unit 4.000 Nos. 0.00

NS-82 Supply installation testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per DAIKIN STD. & specifications, all piping inside the room shall be properly supported with MS hanger.( As per Actual Measurement) 100.000 Rmt. 0.00

NS-83 Control Wiring Duct Ac 7C X 2.5 Sq. mm Supply & fixing of control cum transmission wiring of Copper conductor cable along with conduit for looping between indoor & outdoor system & to main Central remote controller system 130.000 RMT 0.00

NS-84 Drain Piping Duct Ac 32 mm dia, 25 mm dia Supply and fixing rigid UPVC piping complete with fittings, supports as per DAIKIN STD. & specifications and duly insulated with nitrile rubber insulation. 50.000 Rmt 0.00

CASSETTE AC 0.000 0 0.00

NS-85 Installation Charge Per Unit for Four way Cassette AC 11.000 pc 0.00

NS-86 Additional Copper Pipe (per Rmt.) for Cassette AC 165.000 Rmt 0.00

NS-87 UPVC Drain pipe with Insulation (per Rmt.) 110.000 Rmt 0.00

NS-88 Communication Wire - 4 Core 1.5 Sqmm Wire ( Per Rmt.) 198.000 Rmt 0.00

NS-89 Communication Wire - 7 Core Wire ( Per Rmt.) RO Rmt

NS-90 Wrapping Tape RO Roll

NS-91 Nitrogen Pressure Testing & Vaccumming for already installed copper pipes RO ft

NS-92 Wall Cutting-Chiseling RO ft

NS-93 ODU Stand As Per Unit Drawing Cassette Ac RO Nos

NS-94 Ducting Supply, Installation, Testing & Commissioning of Site fabricated ducting as per SMACNA tech specifications & drawings complete GI Ducting - 24 Gauge ( .60 mm) 150.000 Sqmt 0.00

NS-95 GI Ducting - 22 Gauge ( .80 mm) 80.000 Sqmt 0.00

NS-96 Acoustic Insulation-9 mm thick Providing and fixing of Duct acoustic lining with glass wool insulation, covered with perforated Aluminium 26 Ga, sheet, nuts, bolts etc. complete with all accessory as required. 80.000 Sqmt 0.00

NS-97 Thermal Insulation -13 mm thick Providing and fixing closed cell crossed linked polyethylene insulation on duct complete with all accessory as required. 150.000 Sqmt 0.00

NS-98 Grilles/Diffusers Supply, Installation and Testing of Supply & Return Air grilles/ diffusers as per specifications and drawings. Powder Coated Extruded Aluminium supply/exhaust air grill as per specs & drawing 100.000 Rmt 0.00

NS-99 Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. 6.000 Nos 0.00

NS-100 Duct Color vcd damper 6.000 Sqmt 0.00

NS-101 Ventilation Cabinat Fan 4500 CFM Installation Installation, testing and commissioning of Ventilation Fan Units. 1.000 Nos 0.00

NS-102 Ducting-GI Ducting - 24 Gauge ( .60 mm) Supply, Installation, Testing & Commissioning of Site fabricated ducting as per SMACNA tech specifications & drawings complete 70.000 Sqmt 0.00

NS-103 Grilles/Diffusers Supply, Installation and Testing of Supply & Return Air grilles/ diffusers as per specifications and drawings. Powder Coated Extruded Aluminium supply/exhaust air grill as per specs & drawing 0.500 Sqmt 0.00

NS-104 Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. 1.000 Nos 0.00

NS-105 Refrigerant R-410 Refrigerant Charging 60.000 Kg 0.00

NS-106 ODU STAND FABRICATION DUCT UNIT ODU Stand As Per Unit Drawing RO Nos

NS-107 KIRLOSKAR, IOT Enable, 1010 kVA DG set with Genset Model- KG1-1010WS & Engine Model DV16ETA, 16-cylinder developing 1210 BHP & coupled with KG-make Alternator Liquid Cooled with Control Panel, Acoustic Enclosure & Base frame having inbuild fuel tank of 990 Ltrs 1.000 Set 0.00

TOTAL (Non Schedule) : Rs.