ALTERATION ADDITION AND SPECIAL REPAIRS TO BLDG NO. Z, H, I AND J AT OLD NAVY NAGAR, COLABA MUMBAI

Amount

Material & Labour for chipping, removing carefully concrete work by low impact hammer, breaker without damaging the structure and cleaning and disposal of debris out side the MoD land etc complete as directed by Engineer-in-charge. Note: Hard concrete should not be removed by force.

Mixing and applying SBR latex modified cement mortar 25 mm thick in cement sand mortar in proportions of 1:3 (1 part cement and 3 parts quartz aggregate) with polymer admixed in proportions as approved, including trowelling with wooden tools on prepared concrete surfaces of parent material complete all as specified and as directed by the Engineer-in-charge. (Note: Rate includes the rate of steel scaffolding. No separate payment Shall be paid for scaffolding) (Note: SBR latex shall be will be measured and paid separately as supply only).

Mixing and applying SBR latex modified cement mortar 30 mm thick in cement sand mortar in proportions of 1:3 (1 part cement and 3 parts quartz aggregate) with polymer admixed in proportions as approved, including trowelling with wooden tools on prepared concrete surfaces of parent material complete all as specified and as directed by Engineer-in-charge. (Note : Rate includes the rate of steel scaffolding. No separate payment shall be paid for scaffolding). (Note: SBR latex will be measured and paid separately as supply only).

Providing and application of hitech concrete penetrating, water based, organic, Bi-polar, calcium nitrite free, migratory corrosion inhibitor on concrete surface having pH 9.5 which migrates to a virtual extent of 100 mm inside concrete through pores, to inhibit the corrosion process on embedded steel at both anodic and cathodic ends by depassivating the electro-chemical reaction in that region thereby protecting rebar on all sides.

Cleaning the existing reinforcement with wire brush/ rotary wire brush to make surface free from rust scales, loose material, dirt etc. complete and providing, applying two coats of alkaline rust converting primer confirming to ASTMB-117, on the existing rebars and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, with time interval of 1 hour between the coats.

Providing and application of full and unbroken coating of anticorrosive protective zinc rich epoxy coating on exposed reinforcement in two coats with time interval of minimum 1 hours between each coat including mixing of both components by weight as per manufacturer's specifications, brush application, curing to form a anticorrosive protective coating with high mechanical strength to cementitious repair works, etc complete.

Mixing and applying SBR latex modified cementitious bond coat using cement 2.2 kg per square metre on prepared concrete surfaces of parent material complete all as specified and as directed by the Engineer-in-charge. (Note: SBR latex shall be paid for separately).

Rebuilding the section of damaged RCC elements to required size avg thickness upto and including 50 mm by providing and casting with microconcrete of grade M-40 or above including providing and fixing of watertight shuttering of minimun 12 mm thickness with supporting framework, all lead lift, mixing, placing, deshuttering, levelling the surface by grinding off cementitious slurry or construction joint differences if any to satisfaction of the Engineer-in-charge, etc. complete.

Rebuilding the section of damaged RCC elements to required size avg thickness beyond 50mm upto and including 70 mm by providing and casting with microconcrete of grade M-40 or above including providing and fixing of watertight shuttering of minimun 12 mm thickness with supporting framework, all lead lift, mixing, placing, deshuttering, levelling the surface by grinding off cementitious slurry or construction joint differences if any to satisfaction of the Engineer-in-charge, etc. complete.

Drilling Holes of 12mm dia, upto 100mm deep in structural members at the intervals of 300 to 500mm in staggered manner or along the crack as directed by the engineer-in-charge in RC structural element including cleaning of the holes by air blower and inserting 12mm dia. teflon nozzles compatible with epoxy injector and having machined external end to receive outlet of grouting gun. Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and allow to cure the system for min. 8 hrs before grouting including removing nozzle projections, excess putty if any over concrete element grinding, levelling and finishing the external surface, after completion of the work, etc complete all as specified and as directed by Engineer-in-charge. Note: Epoxy putty cost is to be included in the quoted rate. Drilling of hole shall be done by authorized applicator and the work shall be executed in the presence of the company representative.

Grouting injecting low viscosity high molecular weight thermosett polymer Monopol 250 H by pressur and using pressure epoxy injector with accessories till nozzles refused to accept the grout, including mixing material components part a and part b in required quantities as per manufacturer's instructions by weigh batching. Filling the grouting gun with monopol 250 H and maintaining desired pressure in the gun, air compressor and at exit (minimum 3 to 4 kg/sqcm) by a mechanism to monitor both pressure gauges and controlling the same by release valves and release the grout as per requirement simultaneously to grout the structural element through prefixed nozzles till its refusal. Seal the nozzle with thixotropic epoxy putty after the refusal. Note: Leakages through other nozzles or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost. Make: Dr Fixit Epoxy injection Grout/ Sika injection-201 N/ Fosroc conbextra EP 10 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc. so as to withstand a pressure of 0.1 MPa including removal of form from all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies etc. complete all as specified and directed by the Engineer-in-charge.

Material & Labour for mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-charge.

All as per item No 13 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed by Engineer-In-charge

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including disposal of debris out side the MoD land etc complete all as specified and directed by the Engineer-in-charge.

Material & Labour Brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed by the Engineer-in-charge.

Taking down cement or cement lime plaster on brick or stone walls, any description, including raking out joints, hacking for key, scrubbing down with water, etc including disposal of debris out side the MoD land etc complete all as specified and directed by the Engineer-in-charge.

Providing and applying sand face 10mm thick plaster with ready mix prepacked proportioned dry mix mortar, blended with PP fibers, mixed with liquid water proofing compound on other than fair faces of brick wall or concrete surfaces additives, on external surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge. Note:- Liquid water proofing compound shall be measured and paid seperately as supply only.

Providing and applying dubbing coat with forced application (guniting) method avg. 20mm thick plaster with ready mix prepacked proportioned dry mix mortar, blended with PP fibers, mixed with liquid water proofing compound on other than fair faces of brick wall or concrete surfaces additives, on external surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge. Note :- Liquid water proofing compound shall be measured and paid seperately as supply only.

Providing and applying fair finish 15mm thick plaster with ready mix prepacked proportioned dry mix mortar, mixed with liquid water proofing compound on fair faces of brick wall or concrete surfaces, on internal surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge. Note :- Liquid water proofing compound shall be measured and paid seperately as supply only.

Supply only liquid water proofing compound.

Providing and applying fair finish 15mm thick plaster with ready mix prepacked proportioned dry mix mortar fair faces of brick wall or concrete surfaces additives, on internal surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge.

Providing and applying fair finish 10mm thick plaster with ready mix prepacked proportioned dry mix mortar fair faces of brick wall or concrete surfaces additives, on ceiling including transporting of material, mixing, curing, etc. complete as per direction of Engr-in-charge.

Providing & applying anti algal water-based elastomeric exterior wall finish on old as well as newly plastered surfaces including surface preparation, applying suitable wall prime seal primer 8-10 sqm per ltr coverage area and application of two coats (base coat 4.2-4.7 & top coat 6-6.5 sqm per ltr coverage area ) & of paint by roller etc. complete all as specified and directed by the Engineer-in-charge. Make: Dr Fixit Rain coat 601 or any other techno-commercial equivalent in makes mentioned in Particular Specifications. Notes:- 1. Work will be executed by authorised applicator of approved manufacturer. 2. Every coat of finishes will be approved by GE before starting new layer/coat.

Complete removal of existing treatment on wall/ ceiling, roof projections including facia, cornices etc with sanding pad of appropriate grit to Make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed by the Engineer-in-charge.

Material & Labour for applying two coats of oil bound distemper over a coat of primer over wall care putty of average thickness 2mm in two layers on internal surfaces of wall complete all as specified and directed by the Engineer-in-charge. Note: Work will be executed by authorised applicator of approved manufacturer.

Material & Labour for applying two coats of oil bound distemper on old decorated surfaces of wall including complete removal of existing treatment by washing, rubbing down and over 2mm thick putty in two layers complete all as specified and directed by the Engineer-In-charge. Note: Work will be executed by authorised applicator of approved manufacturer.

Material & Labour for preparing new plastered surfaces of wall and applying two coats of white wash complete all as specified and directed by Engineer-in-charge.

Material & Labour for preparing new plastered surfaces of ceiling and applying two coats of Oil bound distemper over 2mm thick putty in two layer complete all as specified and directed by Engineer-In-charge. Note: Work will be executed by authorised applicator of approved manufacturer.

Material & Labour for applying two coats of oil bound distemper on old decorated ceiling including complete removal of existing treatment by washing, rubbing down and over 2mm thick putty in two layers complete all as specified and directed by the Engineer-In-charge. Note: Work will be executed by authorised applicator of approved manufacturer.

Material & Labour for preparing old previously treated wooden surfaces over 10 cm of width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by the Engineer-in-charge.

Material & Labour for complete removal of old treatment and applying two coats of synthetic enamel paint on steel surfaces of any description complete all as specified and directed by the Engineer-in-charge.

Complete removal of exisiting water proofing treatment of roof including demolition of brick bat koba/PCC padding of any thickness, cleaning with wire brushes, etc. and removal of debris outside MoD land, complete all as specified and directed by the Engineer-in-charge.

Material & Labour for providing, plain cement concrete 1:1.5:3 type B-0 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, flooring, rounded or chamfered on edges including necessary formwork (straight of curved) complete all as specified and directed by the Engineer-in-charge.

Material & Labour for protecting the roof including parapet wall with polyurethane hybrid next generation liquid applied roof top coat waterproof coating with flutyne protection technology, complete as specified below:

(a) Apply one coat of primer on cleaned and dry surface spreading at the rate as per manufacturer's instructions and allow primer coat to dry for 6 to 8 hrs. (b) Apply 1st coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution and spreading @ 700 ml/sqm. Allow the first coat to dry for approximately 4-6 hours before applying the 2nd coat at 90° to the first coat. (c) Laying of 45 GSM Fiber glass mesh incorporated on the 1st coating as a sandwich layer when the first coat is still in wet condition. Sandwich layer will not be considered as second coat. (d) Apply 2nd coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution at 90° to the first coat and spreading @ 700 ml/Sqm. Allow the first coat to dry for approximately 4-6 hours before applying the 3rd coat. (e) Apply 3rd coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution at 90° to the 2nd coat and spreading @ 700 ml/Sqm. Ensure there are no pinholes or air bubbles on the membrane. (f) Allow the system to air cure for 7 days minimum. Minimum thickness will be 1.2mm to 1.6mm after 7 days. Makes for polyurethane hybrid next generation liquid: Dr. Fixit Roofseal Ultra, POLYBIT POLYTHANE P, SikaRoof® PUR-18 or any other techno-commercial equivalent.

Material & Labour for Water proofing treatment to rain water spouts of entire roof terrace by opening of all the existing failed loose pipes and its joints (in old structure), replacing the same by an appropriate dia pipe (not less then110mm) followed by application of two coats of cold modified bituminous components to ensure leakage free joints (work includes filling of mortar and making good the same) complete all as specified and as directed by the Engineer-in-charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for and removal of debris outside MoD land, complete all as specified and directed by the Engineer-in-charge.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas, parapet wall, chimny, wall and similar suspended work including cutting of reinforcement cut as required to facilitate demolition including removing of debris out side MoD land complete all as specified and directed by Engineer-In-charge. (Reinforcement cut as required to facilitate demolition) Note: (i) Before quoting the tender, the bidders are advised to ascertain the distance outside MoD land at which the excavated material/ debris are to be disposed off. No extra claim what-so ever shall be entertained on this account. (ii) This item shall be considered as per the requirement at site.

Excavation in trenches not exc 1.50m wide and not exc 1.50m in depth for foundation etc not exc 10sqm on plan and not exc 1.50m in depth and getting out in hard/dense soil complete all as specified and directed by the Engineer-In-charge.

Demolition and breaking up SWG drain pipe of 150mm dia complete all as specified and directed by the Engineer-in-charge.

All as per item No 40 above but 200mm dia.

Material & Labour for concrete bed to drain pipes in cement concrete (1:3:6) type C2, 150 mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and directed by the Engineer-in-charge.

All as per item No 42 above but 200mm dia.

Material & Labour for 150mm bore Reinforced concrete pipes, Class NP2, laid in trenches and jointed with cement slurry and yarn complete all as specified and directed by the Engineer-In-charge.

All as per item No 44 above but 200mm dia.

Cutting into existing manholes for connecting new drains of 150mm dia pipe and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specied and directed by the the Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by the Engineer-in-charge.

Removing excavated material (any type) and disposing it outside Ministry of Defence Land complete all as specified and directed by the Engineer-in-charge. Note: (i) Before quoting the tender, the bidders are advised to ascertain the distance outside MD and at which the excavated material/ debris are to be disposed off. No extra claim what-so ever shall be entertained on this account. (ii) This item shall be considered as per the requirement at site.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/sqcm of fixed to wall, floors for drain out the waste water from Kitchen Sink, WHB etc including socket, tee, bend etc & screw complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 40mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm of fixed to wall, floors for drain out the waste water from Kitchen Sink, WHB etc including socket, tee, bend etc & screw complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC (SWR) 110mm bore pipes in any length with rubber ring joints fixed to wall with dash through fastners and rain water bracket suitable for 110mm pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 110mm PVC (SWR) bends with access door complete all as specified and as directed by the Engineer-in-charge.

Supply & Fixing PVC (SWR) branch piece, Single (single Y) equal or unequal for 110 mm bore access door eye complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC (SWR) branch piece, double (double Y) equal or unequal for 110 mm bore access door eye complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 110mm bore PVC floor trap with SS gratings including jointing to waste pipe with solvent cement complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 110mm bore PVC (SWR) vent cowl complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC (SWR) 160mm bore pipes in any length with rubber ring joints fixed to wall with dash through fastners and rain water bracket suitable for 160mm pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 160mm PVC (SWR) bends complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for 160 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 160mm bore PVC (SWR) vent cowl complete all as specified and directed by the Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposal of debris out side the MoD land etc. complete all as specified and directed by the Engineer-in-charge. Note: (i) Before quoting the tender, the bidders are advised to ascertain the distance outside MD and at which the excavated material/ debris are to be disposed off. No extra claim what-so ever shall be entertained on this account. (ii) This item shall be considered as per the requirement at site.

Material & Labour for non skid ceramic digital coloured ceramic tiles 7 to 8 mm thick of size 400mm x 400mm in floors etc. set and jointed in neat cement slurry over 15 mm thick screed bed in cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and directed by the Engineer-in-charge.

Material & Labour for digital coloured ceramic tiles 300x450x7-8 mm thick in vertical surfaces (including designed borders) such as skirting and dados set and jointed in neat cement slurry pointed in coloured cement to match over rendering 10 mm thick on fair faces of brick work in CM (1:4) complete all as specified and directed by the Engineer-in-charge. Note:- Rate of Designer border in vertical surface shall be deemed to be included into quoted rate.

Material & Labour for glazed Vitrified tiles of size 600mmx600mmx8-9mm thick in floors over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-charge.

Material & Labour for glazed Vitrified tiles of size 600mmx600mmx8-9mm thick in skirting over & including 10mm thick cement plaster in cement mortar (1:4) and pointed in white or coloured cement to match complete all as specified and as directed by the Engineer-in-charge.

Demoliton of Stone slabs and tiles of any description or thickness in floors, aprons etc laid beded and pointed in any mortar including removal outside of MoD land complete all as specified and directed by the Engineer-in-charge. Note: (i) Before quoting the tender, the bidders are advised to ascertain the distance outside MD and at which the excavated material/ debris are to be disposed off. No extra claim what-so ever shall be entertained on this account. (ii) This item shall be considered as per the requirement at site.

Material & Labour for machine cut pre-polished kota stone slab as in flooring, steps, window cill and jams etc or similar work 18-20mm thick over and including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes laid and jointed with grey cement slurry mixed with pigment in cement mortar (1:6) to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engineer-in-charge. (Note : The rate includes the cost of cement screed bed)

Material & Labour for 18-20mm thick machine cut pre-polished kota stone slab in riser of steps, skirting, dado and pillar laid over and including 15mm thick plaster in cement mortar (1:3) on fair faces of brick work or concrete surfaces and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engineer-in-charge.

Material & Labour for udaipur green/baroda green marble slab 18-20 mm thick on vertical surface, machine cut, bedded and jointed with grey cement slurry over and including 15mm thick plaster in cement mortar (1:3) and pointed with white cement using marble dust with admixture of pigment to match the shade of marble slab including grinding and polishing complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 18-20 mm thick Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over and including bedding layer of 20mm thick in cement mortar (1:4) for laying floor finishes including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by the Engineer-in-charge.

Rounding of edges of stone slabs (kota/granite etc) one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by the Engineer-in-charge.

Material & Labour extra for forming grooves over granite or kota stone slab as in staircase complete all as specified and directed by the Engineer-in-charge.

Material & Labour for Reinforced cement concrete (design mix) M-25 (using 20mm graded aggregate) for Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses and mass concrete complete all as specified and directed by the Engineer-in-charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings or chajjas. (FRP or any other pattern)

Supply & Fixing pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

Cutting chases, pinning in and making good to facings of brick/concrete/stone walling where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by the Engineer-in-charge.

Material & Labour for filleting in any position and to any shape of section area not exc 25 sqcm in cement sand mortar 1:4 including all mitres, stops, etc. complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 10 mm dia 100 mm long dash through fasteners bolts fixed in concrete or brick work to hold brackets etc. complete all as specified and directed by the Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

Supply & Fixing rolled section as in main and cross beam, hip and jack rafters, purlins where connected to common rafter and running rails etc. complete conforming to Fe-290-W(Gde E-165) quality B including working platform/scaffolding complete all as specified and directed by the Engineer-in-charge.

All as per item No 83 above but fixing only complete all as specified and directed by the Engineer-in-charge.

Material & Labour for preparing of new steel surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by the Engineer-in-charge.

Taking down shutter exc 1 sqm but not exc 2 sqm each and refixing in the same opening after easing and adjusting complete all as specified and directed by the Engineer-in-charge.

Taking down shutter not exc 1 sqm each and refixing in the same opening after easing and adjusting complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Aluminium anodised frame for door, windows, ventilators etc. with one or more rebates including joining cleat for fixing etc.fixed type/louvered window or ventilator without sash bar, aluminium including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, sliding rollers, rubber gasket etc. complete all as specified and directed by the Engineer-in-charge. Note: a) Glazing shall be measured seperately. b) Item shall be paid as per weight of aluminium section. c) The rate quoted shall be inclusive of neoprene beading, glazing clips, screws, etc., as required which shall not be measured for arriving the weight. d) The rate shall be inclusive of the locking arrangement including complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing surface area. Note: - The size of aluminium section shall be as per HQ CE(N) MZ TD Drawing No. TD/2021/01 to 05 and Sill to be provided as per HQ CE(N) MZ TD of Sill Type 'A' and 'B' repectively. The contractor shall provide Granite stone slab (The rate of granite shall be paid seprately under respective item) with width equal to the thickness of wall all around the window opening any cutting required to jamb and sill to accommodate the aluminium window shall be done including make good the disturbed surfaces shall be include in the quoted rate againt the item.

Material & Labour for grill with suitable aluminium anodised frame section manufactured by M/S Deco grill pattern DG-102 (7.5mm thick and aparture 50mm) or any other techno commercial equivalent in repair complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 5.5 mm thick plain glass ordinary quality in square not exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 5.5 mm thick frosted glass ordinary quality in square not exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or wooden/ Aluminium beading complete all as specified and directed by the Engineer-in-charge.

All as per item No 92 above but fixed in repairs complete all as specified and directed by the Engineer-in-charge.

Taking down chowkhats or frame (w/o taking off shutters from the frames) exc 1.50 but not exc 4.00 sqm each complete all as specified and directed by the Engineer-in-charge.

Taking down chowkats or frame (w/o taking off shutters from the frames) not exc 1.50 sqm each complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 2nd class hard wood plain, solid straight chowkats and frames, wrought framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing 2nd class hard wood 35mm thick factory made plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial or 12mm veneered particle board with commercial veneer on both faces. The size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 2nd class hardwood 35mm thick skelton shutters, open rebated and prepared to receive wire mesh edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing mesh etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing 2nd class hardwood bullnosed splayed, chamfered or rounded on edge fillets rectangular in section, sectional area exc 6 but not exc 13 sqcm fixed in repairs fixed with nails complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 2nd class hardwood bullnosed splayed, chamfered or rounded on edge fillets rectangular in section, sectional area exc 13 but not exc 25 sqcm fixed in repairs fixed with nails complete all as specified and directed by the Engineer-in-charge.

Material & Labour for preparing new wood or wooden surfaces over 10 cm of width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing MS holdfast, wall ties and similar articles confirming to Fe-290 Gde- E-165 complete all as specified and directed by the Engineer-in-charge.

Material & Labour for PCC (1:3:6) type C-1 (20mm graded agg) for fixing of hold fast complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 90 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with SS dash fasteners of required dia and length complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by the Engineer-in-charge. Note: stainless steel butt hinges shall be paid separately

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and complete all as specified and directed by the Engineer-in-charge.

Taking down shutters of any description not exc 1 sqm each complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 18-19mm thick Block boards, grade1 quality, interior grade, decorative type with decorative face veneer on single side and white veneer on other face fixed with screws to timber frame-work including teak wood lipping, 6mm thick fixed with nails as in Cup board shutter and shelves complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 100mm size SS butt hinges fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing stainless steel grade 304, 100 mm long barrel tower bolt fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing stainless steel grade 304, 150 mm long barrel tower bolt fixing complete all as specified and directed by the Engineer-in-charge.

All as per item No. 111 above but fixed in repairs complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing stainless steel grade 304, 100 mm decorative type pressed handle fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing stainless steel grade 304, 150 mm decorative type pressed handle fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair stainless steel grade 304, 150 mm decorative type pressed handle fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing stainless steel grade 304, 300 mm long SS sliding door bolt plate type decorative with bright bolt not less then 12 mm dia with and incl min of 6 bolt and nuts, four on bolt plate and two on staple fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair stainless steel grade 304, 300 mm long SS sliding door bolt plate type decorative with bright bolt not less then 12 mm dia with and incl min of 6 bolt and nuts, four on bolt plate and two on staple fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Stainless steel two leg Floor door stopper of 100mm fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair Stainless steel two leg Floor door stopper of 100mm fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 125mm size SS butt hinges fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair stainless steel hasp and staple 150mm size, safety type, fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate fixed with SS screws complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing 600mm long stainless steel kitchen rail, wall mounted type with 10 Nos of hooks made of 3mm dia SS rod and welded/ riveted on 20mm x 2mm flat SS and necessary screws, pluges fixed with SS screws complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing stainless steel cloth hanger peg set of 6 of premium quality fixed with CP brass screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing magic eye fancy type of brass for door including drilling cutting of holes and making good complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing chromium plated towel ring fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Material & Labour for welded mesh not exc 4 kg/sqm of size 25mm x 25mm including beading, fillets, nails including dismantling old unserviceable mesh complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 75mm thick PCC (1:3:6 ) type C-1 using 20 mm graded stone aggregate as in plinth protection laid in panels, finish the top surfaces even and smooth complete all as specified and directed by the Engineer-in-charge.

Material & Labour for cement concrete 1:4:8 type D2 using 40mm graded aggregate as in hardstanding, filling mass concrete in foundation complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' or 'S' trap including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover including connecting to trap and flushing pipe, anti-syphonage pipe etc and screwed with ms screws complete all as specified and directed by the Engineer-in-charge. Make & Model : EWC "CONVENTIONAL" CAT part No. S1053102 of CERA and seat cover "CAJOL" CAT Part No. B1510123 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair 15 mm bore fancy type health faucet with SS hose complete all as specified and directed by the Engineer-in-charge. Make:- Cera CAT Part No. F 8030106AB or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repairs 10 litres capacity, PVC valveless, low level, syphonic type, white, plastic twin flushing cistern with inlet, ball valve, float and handle including brackets complete all as specified and directed by the Engineer-in-charge. Make: Model 'COMPASS' CAT Part No. B1020106 of CERA or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Material & Labour stainless steel 25mm curtain rod dia complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing stainless steel 100mmx20mmx1mm fancy type brackets including stainless steel domes 25mm dia complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair CP soap dish complete all as specified and directed by the Engineer-in-charge. Make:- Cera CAT Part No. F 5002106 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair fancy type CP Towel Rail 61 cm long complete all as specified and directed by the Engineer-in-charge. Make:- Cera CAT Part No. F 5007101 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing wash basins, vitreous china, white, flat back, of size 550mm x 400mm x 140mm or nearest size conforming to model 'CALBURT' CAT Part No. S2020137 of CERA or any other techno commercial equivalent in Jaquar, Perryware or Hindware with and including cast iron brackets [embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws], 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and table top basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and directed by the Engineer-in-charge. Make : CALBURT' CAT Part No. S2020137 of CERA or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair 15 mm bore pillar taps swan neck cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettered 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed by the Engineer-in-charge. Make:- Cera CAT Part No. F 2008105 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Material & Labour for 32 mm dia waste coupling of CP including waste pipe complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC connectors of 15 mm size with PTMT nuts of length 600 mm length complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs sinks with draining board made of stainless steel 1mm thick, kitchen with plugs, washers & wastes cupling and waste pipe including fixing cantilever brackets & connecting union to pipe overall size 915mm x 460mm and bowl size 410 x 330mm x 160mm complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs stainless steel plate rack 0.63mm thick stainless steel sheet overall size stainless steel plate rack 31” x 31” x 10” kitchen rack all as specified and as directed by the Engineer-in-charge.

Supply & Fixing of 04 pieces pulley operated clothes drying system casting of Aluminium pipe of outer dia 22 mm inner dia 19.8 mm and channel pair of length 2.50 mtr with pulley made up of devil mounted and fixed with self tapping screw. Rope will be HDPE double core of 4 mm with rope guide at locking system to hide rope. Minimum weight of pipe shall not be less than 0.20 kg/Rm and maximum weight of pipe in one unit not less than 2 kg. Weight of rope shall be not less than the 550 gms/mtrs.

Supply & Fixing for Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffener and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed by Engineer-in-charge. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Supply & Fixing of 18 mm thick Celuka ply of Plain colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets matching edge beading on exposed face of board edges complete as per specifications and directed by the Engineer-in-charge.

Supply & Fixing of 18 mm thick Celuka ply of one side Prelam and other side plain white colour to make kitchen cabinet Shutter/ drawer front shutters in double panel including matching edge beading on exposed face of board edges complete as per specifications and as directed by the Engineer-in -charge.

Supply & Fixing of SS auto closing hinges openable at 0/90 degree for kitchen cabinet shutters.

Supply & Fixing of stainless steel handles 100 mm size for kitchen cabinet shutters.

Supply & Fixing for number plate made out of 3mm thick acrylic sheet and size 100mm x 180mm including written 4 to 5 numeric & letter height not less than 65mm (colour, design & pattern as approved by EIC) fixed with CP brass screws complete all as specified and directed by the Engineer-in-charge.

Material & Labour for two coats of floor guard paint on surface of old paver block and concrete tiles including cleaning with brush and water to prepare clean surfaces complete all as specified and directed by the Engineer-in-charge.

Material & Labour for providing and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion at 2.25 litre per linear Metre including drilling and plugging holes etc with white cement and match the surface to existing apron complete all as specified and directed by the Engineer-in-charge.

Material & Labour for treatment of soil under existing floors in junction with wall (internally) using chemical emulsion @ 1 litre per hole at 300mm center to center and 300mm deep including drilling and plugging 12mm dia holes with cement mortar 1:2 or white cement to match the existing floors complete all as specified and directed by the Engineer-in-charge.

Material & Labour for post construction treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors all as specified and as directed by the Engineer-in-charge.

Material & Labour for post construction treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with sealing compound complete all as specified and directed by Engineer-In-charge.

Material & Labour for sand filling under floors or in foundation including watering and consolidation etc complete all as specified and directed by the Engineer-in-charge.

Material & Labour for cement concrete 1:3:6 type C-2 with 40mm graded brick coarse aggregate in sunken floor complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 60 mm thick coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and as directed.

Supply & Fixing for 20mm thick Granite corner shelf of 1/4th circular of dia 200mm embeded into the wall and filling the gap with grout complete all as specified and directed by the Engineer-in-charge.

Treatment of sunken floor slab comprises of the following specifications and all as specified

(i) Material and labour for cleaning of the sunken /lowered portion of the RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chiesel out any mortar sticking to the surface and brooming / washing completely. 40 mm avg thick PCC 1:2:4 type B-0 using 12.5 mm graded aggregate as in padding concrete to achieve proper slope including 50 mm dia 350 mm long medium grade GI pipe spouts with wire guage on inside mouth to be fixed. (ii) Rendering of uneven surfaces with 10 mm thick using factory manufactured pre mix / ready mix mortar addition and including WPC of UltraTech WP+ 200 or other equivalent @ 200ml per bag of mortar fill it with water and check dampness and seepage. where dampness and seepage noticed nozzles shall be fixed and grouting carried out. (iii) All junctions points of side walls where CI/GI pipes are passing through shall be sealed with epoxy putty (iv) After drying putty wash the slab and sides of sunken portion with water and make it clean and clear (v) Material and labour for applying two coat of polymer modified cementious water proofing coating as per manufactures instructions to bottom and vertical sides up to finished flooor level +100 mm height. The thickness of two layer shall be 1 mm. When the second layer is still sticky, coarse sand spry shall be carried out or vertical and bottom surface of the sunken portion all as specified and directed. (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20 mm thick using factory manufactured pre mix / ready mix mortar addition and including WPC of UltraTech WP+ 200 or other equivalent @ 200ml per bag of mortar including rounding of corners and junctions sloping towards spout. Note:Test the water proofed area (ponding test) by filling water for atleast 72 hours and tested for leakage seepage and to the entire satisfaction of GE . Test shall be done in presence of reps of PMG and record for each sunken slab shall be maintained. the treatment shall be carried out by authorised applicators of chemicals. (vii) All pipes laid in sunken portion shall be covered with 50 mm thick PCC 1:2:4 all around after painting with anticorrossive black japan paint

Supply only approved SBR Latex polymer. (Note: Rate shall be in terms of solid contents of polymer).

Taking down old Aluminum window and kept in safe custody and refixing in same opening after external plaster and repairing of window, cill & jambs including minor repairing like fixing of scews etc

Internal Electric Supply

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition sepertately) and making good disturbed surfaces of walls, floors etc. Note: Serviceable tube lights etc shall be kept under safe custody and refixed as directed.

Material & Labour for point wiring confirming to IS-732:1989 complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheated copper conductor,1100 volts grade confirming to IS-694:1990 drawn through and including rigid non-metallic PVC medium grade concealed conduit of suitable size having thickness not less than 1.2mm ISI marked with accessories concealed in wall/floor including cutting chases, pining etc with modular metallic ISI marked terminal boxes, concealed in wall including one FRLS PVC insulated and unsheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for the following :- Note : - (i) Circuit conductor from MCB DB to Switch boards should not be less than 2.5 sqmm for: (a) swich boards having light/fan points and 6A socket in common circuit. (b) socket outlets 6A with maximum 4 points in one circuit. (ii) Modular metal flush box shall be paid seperately under relevant items of this schedule. (iii) In ceiling portion and in case of columns coming in way of concealed conduit, casing caping of suitable size shall be used. No extra cost shall be paid for the PVC casing capping item.

One light/Exhaust/Ceiling fan point controlled by one switch SP one way.

One 3 pin socket combination 5 Amps on same board.

One 3 pin socket combination 5 Amps on independent board.

One bell point controlled by one push button 5 amps on independent board.

All as per item No. 165.0 here in before point wiring confirming to IS-732:1989 but for 15 amps socket complete with 2.5 sqmm single core multi stranded FRLS PVC insulated unsheated copper conductor 1100 volts grade confirming to IS-694:1990 drawn through and including rigid non-metallic PVC medium grade concealed conduit of suitable size having thickness not less than 1.2mm including one FRLS PVC insulated and unsheathed multi stranded green colour copper conductor 2.5 sqmm as earth continuity conductor connected to comon earth as earth dolly. Note:- (i) Circuit conductor from MCB DB to Switch boards should not be less than 2.5sqmm. (ii) Separate circuit shall be drawn from MCB. No taping from light circuit. (iii) Modular metal flush box shall be paid separately under relevant items of this schedule.

Supply & Fixing modular switch, 6 Amps , One way, one module , ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular type bell push 6 amps 1 module, ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular switch, 16 Amps , One way, one module , ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing bell electric AC 230 Volts single pole ding dong with ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular socket, 6 Amps , 2/3 pin combined , two module , ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular socket, 16 Amps , 6 pin combined , two module , ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular socket, 10/20 Amps, 6 pin, two module, ISI marked complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing modular switch, 20 Amps, one way, one module, ISI marked complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing modular TV Socket including flush box and cover plate with frame complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing ceiling rose surface bakelite with ISI mark , flush type three terminals complete all as specified and directed by Engineer-In-charge.

Supply & Fixing Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular stepped type fan regulators 2 module, 120 W, 230 volts ISI marked complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 1 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 2 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 3 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 4 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 6 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular metal flush box 8 module and including cutting hole in wall and making good surface complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 1 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 2 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 3 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 4 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 6 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing modular white cover plate with frame 8 module complete all as specified and directed by Engineer-In-charge.

Supply & Fixing integrated LED batten 20 Watt, 4 feet long, full white in Engineering plastic pattern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting along with provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings complete all as specified and directed by the Engineer-in-charge.

Refixing of old serviceable LED tube light upto 20 watt including sensor based all as specified and as directed by Engineer-In-charge. Note: Tube light taken down vide item No.01 shall be reused.

Supply & Fixing integrated LED batten 10 Watt, 2 feet long, full white in Engineering plastic pattern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting along with provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 10W LED batten with inbuilt smart motion sensor, 230 Volt, 50 Hz, 2 feet, polycarbonate extruted channel, with diffuser for glare free light, Inbuilt motion sensor pre-wired with 25% dimmer illuminous in ideal time with all accessories including connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting along with provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair MCB DB SPN 12 way suitable for single phase AC supply, 230 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection with built in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed by the Engineer-in-charge. Note:- Blanking plate shall be used for blank places in DB.

Supply & Fixing ISI marked 32 Amp, 30mA, 230V, DP RCBO for AC applications, conforming to IS:12640 (Part 2)-2016, having front face indication for earth leakage fault, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP20 protected lower terminals and sliding shutters including taking down old unservicable MCB SPN, 32 Amp complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing including taking down old unservicable MCB, single pole, 6 to 32 Amp, 10KA, 230Volt.

Material & Labour for submain wiring conforming to IS-732:1989 in rigid non-metallic medium grade ISI marked PVC conduit using 2 runs of 6 sqmm PVC insulated stranded copper conductor, single core, FRLS conforming to IS 694:1990 including single run of 6 sqmm stranded copper conductor as earth wire including taking down unserved submain wiring all as specified and as directed by the Engineer-in-charge. Note:- (i) 03 Runs x 6 sqmm copper wire for phase, neutral & earth and 01 run of PVC conduit shall be measured as 01 Running Metre. (ii) Cutting chases, pinning in, making good to facings where required for concealed conduit wiring shall be deemed to be included in the quoted rate. (iii) PVC casing caping wiring shall be provided where concealed wiring is not feasible (i.e. concrete surface/ beam column/ ceiling etc.) The same shall be deemed to include in the quoted rate. No extra cost shall be paid for the PVC casing caping item.

Material & Labour for submain wiring conforming to IS-732:1989 in rigid non-metallic medium grade ISI marked PVC conduit using 2 runs of 4 sqmm PVC insulated stranded copper conductor, single core, FRLS conforming to IS 694:1990 including single run of 4 sqmm stranded copper conductor as earth wire including taking down unserved submain wiring all as specified and as directed by the Engineer-in-charge. Note:- (i) 03 Runs x 4 sqmm copper wire for phase, neutral & earth and 01 run of PVC conduit shall be measured as 01 Running Metre. (ii) Cutting chases, pinning in, making good to facings where required for concealed conduit wiring shall be deemed to be included in the quoted rate.

Taking down ceiling fan of any size and Make from each flat and keep in safe custody/store after dismantling of fan blades and refixing the same in each flat after completion civil works by following overhauling of ceiling fan, replacement of all unserviceable parts, providind safety GI wire, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust rust, replacement of canopy, bushes, bearing with new including painting of complete fan with synthetic enamel paint and assembling and connecting complete with copper conductor multi stranded 3 core wire of size 14/0.0076 complete all as specified and as directed by Engineer-In-charge.

Overhauling of Exhaust fan any size and Make, dismantling parts, properly cleaning/removing old existing grease, oil and applying new oil grease, varnishing for winding, cleaning dust, rust and replacing petty items with new as required such as Nuts, Bolts, washers, bushes, ball bearing, cap, fan shaft, rotor, capacitor 2.5/4 Mfd, body cover etc and reassembling, connecting with copper conductor multi stranded 3 core wire of size 14/0.0076 complete and testing after refixing at site.

Material & Labour for earthing with steel earth plate electrode of size 60x60cmx6mm thick buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanized iron strip of size 32x6 mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, GI medium grade pipe 40 mm bore protection pipe upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion. NOTE :-Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth wire upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing.

Supply & Fixing in replacement with new cable PVC insulated three core over all PVC sheathed 2.5 Sqmm stranded copper conductor cable for connecion from DB to connector junction box for power supply to security light fittings drawn in PVC cashing capping or PVC conduit not less than 20mm as required at site and as directed by Engineer-in-Charge including taking out old one..

Supply & Fixing in repair junction box of size not less than 4x4 inch with connector encloser, 3 terminal/ PVC/ polycarbonate, isolated body including taking out old one.

Supply & Fixing building security light bracket bend to shape made as required of 25/32mm dia, GI pipe light grade fixed to pole/ Wall including M&L for fixing with the help of flat iron clamp with the help of nuts and bolts for fixing of building security light fitting on the wall complete after taking out old U/S one all as specified and as directed by Engineer-In-charge.

Supply & Fixing including taking down old unservicable LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply & Fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm or nearest size.

Supply & Fixing in repair digital timer switch single phase of current capacity 16 amps with suitable capacity of single phase contactor including any type of accessories like enclosure etc

Material & Labour disconnecting, scrapping old worn out paint from complete indoor type Metre cabin panels and painting with one coats of synthetic enamel paint (incl front door in side and indl compartment outer side etc also) over a coat of primer and spray painting complete including fixing sticker danger sign board suitable for LT panel board and energizing all as specified and as directed by Engineer-In-charge.

Material & Labour for Rigid non-metallic medium grade ISI PVC conduit not less than 20mm dia concealed in wall inclusive of boxes (junction/ terminal) all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. all as specified and directed by Engineer-In-charge. (For TV cable)

Internal Water Supply

Supply & Fixing in repair PVC water storage Tank 5000 ltr capacity 3 layers , ISI marked, White colour, hosting and fixing in position at any location removing existing tank disconnecting all incoming & out going connection , provision of new tank fittings & connecting it at existing position up to 50 mm GI Pipe connection including replacement of tank nipples and GI fittings as required at site, new 40 mm Float valve with complete fitting , provision of PCC blocks under the delivery line on roof complete all as specified and directed by Engineer-In-charge.

Supply & Fixing in repair/replacement of steel water tubing, galvanised, Medium grade of size 50 mm dia with all fittings in shafts such as nipple, union, socket, elbow, bends, fixed to wall including necessary GI/MS clamps in intervals of not exceeding 90 cm length. complete all as specified and directed by Engineer-In-charge. Note :- Supply & Fixing of one GI Union in raising main and one in delivery lines are mandatory and are included in the item rate.

Supplying and laying of CPVC pipes 32 mm outer dia (Inner dia 25 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified by Engineer-In-charge. Note :- Supply & Fixing of one CPVC Union in each delivery lines are mandatory and are included in the item rate.

Supplying and laying of CPVC pipes 25 mm outer dia (Inner dia 20 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified by Engineer-In-charge.

Supplying and laying of CPVC pipes 20 mm outer dia (Inner dia 15 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified by Engineer-In-charge. Note :- Supply & Fixing of one CPVC Union in each Inlet and one in out let of Loft tanks to be fitted in bathroom/kitchen are mandatory and are included in the item rate.

Supply & Fixing in repair/replacement of gun metal gate valves 15 mm , with iron wheel head, screwed both ends for iron/CPVC pipe and fixed complete all as specified and directed by Engineer-In-charge.

Supply & Fixing in replacement of gun metal valves 50 mm , with iron wheel head, screwed both ends for iron/CPVC pipe and fixed complete all as specified and directed by Engineer-In-charge.

Supply & Fixing in repair 15 mm bore fancy type concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-charge. Make:- Cera Cat Part No F 1015361 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in-charge. Make:- Cera Cat Part No F 1015201 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair 15 mm bore fancy type bib taps long body cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by the Engineer-in-charge. Make:- Cera Cat Part No F 1015151 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing in repair 15 mm bore fancy type bib taps long body (two in one) cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by the Engineer-in-charge. Make:- Cera Cat Part No F 1015163 or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply & Fixing PVC loft tank (LDPE) of capacity 275 ltrs, ISI marked, Company name embossing/Painting on tank with complete fitting including 03 Nos adopter with washer for inlet/outlet,over flow as per manufactureres instructions complete including brass float valve (ISI marked) high pressure with polythelene float (flat) and fly nut complete screwed for CPVC pipe 15mm bore all as specified and directed by Engineer-in-Charge.

Supply & Fixing PVC profile suitable for 275 ltrs loft tank including fixing of aluminium channel around the profile complete all as specified and directed.

Supply & Fixing cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections/ladders for over head tanks/base supporting of loft tanks including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint.

Supply & Fixing 15 mm bore overhead shower 250 mm dia single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 240 mm long (light weight) round shape with wall flange complete all as specified and as directed by Engr-in-Charge. Make:- Cera Cat Part No F 7010503AB or any other techno-commercial equivalent in makes mentioned in Particular Specifications.

Supply, Installation in repair, Testing & Commissioning of Motor Actuated Ball Valve consisiting of suitable single phase Actuator and ball valve of size 50 mm dia with appropriate bracket/mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure. Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 10 kg/sq cm. Material of Ball: Stainless Steel Limit Switches : 02 Nos.For open and close status Mounting :Direct on valve Make for motor actuator: Emtork, Ritetork, Honeywell or any other techno-commercial equivalent in makes mentioned in Particular Specifications..

Supply, Installation in repair, Testing and Commissioning of Float type Point Level Sensor with the following specifications; Type: Magnetic, Magnet: Ring type, Switch: Reed Switch (Epoxy sealed) Connecting Cable: Teflon

Supply & Fixing on wall/ laying in trench 6 x 1.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable.

Supply & Fixing on wall/ laying in trench 5 pair 0.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable.

Taking down carefully of SCADA control panel-01 No., motorised valves-06 Nos, magnetic sensors- 12 Nos and cables before starting the special repair work , kept in safe custody without any damage and refixing as per previous location, fixing of cables with saddles and testing after completion of special repair work at site all as specified and directed by Engineer-In-charge. Make: Rectronic devices and systems, Techrol, Crystal or any other techno-commercial equivalent in makes mentioned in Particular Specifications. Note :- Any damaged/malfunctioning of SCADA items/panels at the time of removing/refixing shall be the Contractors responsibility and no extra cost will be given to the contractor for make it serviceable at site.

MUKESH CONSTRUCTION CO

Shree Ayyappa Engineering

Idustrial products India

SHREE KRISHNA INFRASTRUCTURE

ROY CONSTRUCTION CO

United Sales Corporation