SPL REP TO WKSP BLDG NO P-445 AT MT SECTION, ADD/ALTN OF SPL OPERATION CENTRE (SOC) WITHIN ADMIN BLOCK (BLDG NO 721) AND HARD STANDING OF BOAT SECTION, PROVN OF WASH ROOM FOR AOOD ROOM AT INS ABHIMANYU AND SPL REP TO BLDG NO P-748 AT INS TUNIR AT NSK

Amount

Excavation in trenches n.exc 1.5m deep and n exc 1.5 m in width in any type of soil and getting out complete all as specified.

Returning filling in soil incl spreading levelling watering and well running in layers n.exc 25cm complete all as specified.

Removal of surplus soil n.exc 50m and at a level n.exc 1.5m above the starting point and depositing. complete all as specified.

Cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate in fdn filling and mass concrete complete all as sfd.

RCC 1:2:4 type B-1 (using 20 mm stone agg) as in beams, lintel over span 1.5 mtr etc. complete all as specified.

RCC 1:2:4 type B-1 (using 20 mm stone agg) as in slabs, supported on walls beams and columns in floors, roofs, landings, balcony, canopies, deck slabs and in salves and like complete all as specified.

Form work to sides and soffits of floor or roof beams beam launchings, girders, bressumers etc with rough finished complete all as specified.

Form work to soffits of suspended slabs such as roof slabs floor slabs landing and similar works with rough finished complete all as specified.

Form work to edges of concrete flats, breaks in floors, openings in concrete walls,floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exc 10 but n exc 20 cm wide for rough finished flat surfaces of concrete complete all as specified.

M&L TMT bars 10mm dia & over cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with chip with deep quality confirming to FE 500/FE 500D complete all as specified.

M&L TMT Bars 5mm dia and over upto and including 10mm dia in stirrups and spacers and binders complete all as specified.

S&F Brick work with old size brick curved or straight on plan exceeding 6m area radius built in CM 1:4 brick crushing strength not less than 75 kg/cum complete all as specified.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified & directed complete all as specified.

M&L for PCC 1:2:4 type D2 using (40mm graded stone aggregate) as in flooring, 100mm thick etc all as specified and directed.

M&L hard core broken stone of guage n exc 63mm deposited spread and levelled in llayers n exc 15 cm thick watered and rammed to a true surface complete all as specified.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded agg) as in plinth protection finished even and fair w/o using extra cement floor shall be laid alternate panels inluding necessary form work etc all as directed

S&F for aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading,screws etc, complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, hooks & eyes, peg stays and handles, concealed star lock for aluminium window, Mortice lock vertical type size 100mm 04 lever for door, rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors including connected items,with and including making good to the disturbed portion with its original specifications complete all as specified and directed.

S&F 4 mm thick sheet glass , figured glass, pinhead type , glazing with oil putty area not exceeding 0.50 Square Metre each pane complete all as specified and as directed.

S&F for aluminium anodised grill of design DG 104 pattern made out of 10mm dia rod fixed with and including standard aluminium frame of F section of size 23.40mmx15.30mm & 1.4mm thick all as per manufactures instructions complete all as specified & directed. Make- Deco grill or equivalant

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete all as specified and as directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors over screed bed or bedding layer of morar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

M & L for Glazed ceramic tiles in vertical surface 350mmx250mm x7mm / 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering or bedding layer in cement mortar 1:4 complete all as specified and directed.

Flushing cistern with 10 ltrs discharge capacity PVC flushing cistern low level ,including 32 mm PVC flush pipe, with inlet ball valve etc complete all as specified.

Vitreous china wash down water closet (pedestal pattern) white (excluding flushing cistern and flush pipe) including plastic seat cover white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinges device complete all as specified.

S&F Vitreous china boul urinal Half stall type (white) minimum with grating and union for discharge pipe including PTMT spreader of any colour for fixing with 15mm dia pipe of Hind ware or Cera mark.

S&F Vitreous china wash basin white , flat back size 550 X 400 mm including brackets including cutting for and pinning in ends of brackets or erecting stand including PTMT 32mm waste coupling and waste pipe complete all as specified.

S&F Pillar tap cast copper alloy fancy type with capstan heads, chromium plated Fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long shanks and nut screwed for iron pipe of 15 mm bore complete all as specified.

S&F bib taps screwed down high pressure with both ends for iron pipe 15mm bore fancy type chromium plated as complete all as specified.

S&F 15 mm fancy type chromium plated stop valve / angle valve cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe complete all as specified.

S & F Hand shower (Health Faucet) with 8mm dia, 1.2m long Flexible tube & wall hook fixed in pipe complete all as specified and as directed.

S&F steel water tubing medium grade 20mm bore galvanished with all fitting to walls etc. complete all as specified.

S&F steel water tubing medium grade 15mm bore galvanished with all fitting to walls etc. complete all as specified.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified.

S&F PVC shelves of PTMT fixed with and including chromium plated brass screws and plastic cleats complete all as specified.

S&F Towel ring of PTMT fixed with and including chromium plated brass screws and plastic cleats complete all as specified.

S & F CI sand cast pipe , waste and vent pipe duly BIS marked of approved make in any length with or without ears with cement joint of 75 mm bore fixed in trenches or floor.

All as item no. 37.00 but dia of pipe 100 mm complete all as specified.

S&F CI bends duly BIS marked of approved make of (any radius) with duck’s foot or heel rest of 75 mm bore complete all as specified.

S&F CI bends duly BIS marked of approved make of (any radius) with duck’s foot or heel rest of 100 mm bore complete all as specified.

S&F Cast Iron cowl 75 mm bore

S&F Cast iron floor trap with grating including jointing to waste pipe fixed with cement concrete type B-1 (1:2:4 ) , 75 mm dia

S&F water tank with rotational moulded polythene water storage tank (cylindrical vertical with closed top) of 500 Ltr capacity hoisted and fixed in position all as specified in SSR Part I.

S&F Gun-metal Globe or gate valves 20 mm nominal bore dia with gate with iron wheel head screwed both ends for iron pipes and fixed all complete as per direction of Engineer-in-charge.

S&F Toilet paper holder of brass chromium plated fixed to walls with CP screws.

S&F Ball valve high pressure PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete of 20 mm dia

M & L for cutting opening through brick walls built in cement mortar for door, windows or enlarging existing opening, converting window into door openings, etc. or cutting out defective brick work for under pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, and rubbish not exc 50m and depositing where directed complete all as specified all as specified & directed by Engr-in-charge.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debries directed for a distance max upto 500m complete all as specified.

M&L Rendering 15mm thick on other than fair face of brick work in CM 1:6 finished even and smooth without using extra cement.

M&L for rendering 20 mm thick on fair faces of brick/concrete surfaces with two coats i.e (15 mm thick backing coat in CM (1:6) and 5mm thick finishing coat in CM (1:4)) , finished even and smooth without using extra cement (WPC to be measured and paid separately) complete all as specfified and directed.

M&L Rendering 5mm thick on concrete surface in CM 1:3 as in ceiling finished even and smooth without using extra cement complete all as specified.

M & L for preparation of new or previously untreated plastered surfaces of walls and applying two coats of acrylic antifungal paint exterior grade paint in plain or camouflage pattern on one coat of primer complete all as specified and as directed

Applying three coats of white wash on ceiling including preparation of new or untreated surfaces complete all as specified.

M&L prepration of old plastered / decorated surfaces of walls and applying one coat of oil bound distemper on plastered/decorated wall surfaces complete all as specified and directed.(Note:- Item rate shall be include any height of Bldgs / Hangars for scafolding as all arrangement.)

M & L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer including 3mm thick wall care putty on plastered surfaces complete all as specified and directed.

S & F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified.

M&L concrete bed to drain pipes laid in trenches incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregates) for 150mm bore of pipe all as specified

M&L Salt glazed stone ware (SGSW) grade 'A' pipes 150mm bore laid and jointed on concrete bed complete incl testing all as specified (Concrete to be measured and paid for separately).

M&L Rendering 15mm thick in CM (1:4) on fair faces of brick workor concrete surfaces, finished even and smooth without using extra cement mixed with water proofing compound @ 3% by weight of cement all as specified.

Supply only integral water proofing compound.

M&L Cement Concrete 1:2:4 type B1 (using 20mm graded crushed stone agg) as in coping incl weathering slightly rounded or chamfered angles as directed incl necessary form work and finishing the exposed surfaces complete all as specified

M&L precast Reinforced cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) as in man hole covers set in cement mortar 1:6 all as specified and directed incl necessary form work.

Cutting into existing man hole for connecting new drains, making good to pipe of bore 150mm, and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified.

Moorum/ red bajri/ approved earth filling in floors or pavings not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified.

M/L 15 cm thick (compacted thickness) WBM in two layers(7.50 cm Each), Lime stone/sand stone with course aggregates of grading 2 (63 to 40mm size) spread, rolled and consolidated to gradient and camber required meterial . complete all as specified and directed by Engineer-in-charge.

M&L Cement concerete work in pavement/ hard standing of flexural strength 40 Kg/per Sqcm in field using 400Kg of cement per cum thickness of concerete 25 cm or less. complete all as specified and directed by Engr in charge. Notes : Approval of PQC M-35 grade (Design Mix) to be taken from GE and RMC to be used.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A'. complete all as specified and directed by Engr in charge.

M&L for finishing surface of concrete hard standing, pavements, by brooming. Complete all as specified and directed by Engr in charge.

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube and edgeswill be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed.(Make : Rajshree,Plastiwood, Sintex or equivalent as approved)

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube top & bottom rail mild steel frame shall be covered with heat moulded plain colour PVC “c” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F butt hinges size 100 extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed C-21 complete all as specified and as directed.

S&F 125mm long Extruded aluminimum alloy handles, fabricated type complete all as specified and as directed.

S&F Aluminium anodized, barrel tower bolt of extruded section, length of bolt 150 mm complete all as specified and as directed.

On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 10 Users

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 1.5 M effective depth

Chipping , removing carefullly concrete work by low impact hammer ,breakar without damaging the structure & cleaning and disposal of debries out side the premises etc. complete as directed by Engr-in-Charge. Hard concrete should not be removed by force.

M&L for Clean existing reinforcement with wire/ rotary wire brush, making the surfaces free from loose material dirt etc. complete and applying two coats of alkaline rust converting primer FEOVERT of Krishna Conchem or Roff rust cleaner of Piddilite or Dr. Fixit Rust removal or ShaliRust of STP Ltd. on the rebars, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, wash the rebars with clean water within 3 min and wipe it dry.

M&L for applying two coats of Epoxy based Zinc primer in a span of four hours over the treated rebars and allow to dry for six hours. The application shall be by brush. Epoxy primer for steel of make / brand - Corroseal-ZR of Krishna Conchem or Dr. Fixit Epoxy zinc primer

M&L for cleaning all loose laitance on the concrete substrate and applying one coat of epoxy bonding agent on exposed concrete surface to ensure bond between old concrete & new concrete by brush application. Make / brand Monobond SBR of Krishna Conchem or Dr. Fixit epoxy bonding agent or Shalicrete URP of STP Ltd.

M&L for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5Cement-15 sand) -in damaged areas in 30 to 40mm thickness including leveling profliling etc complete all as specified.

M&L for applying concrete protection coating on finished structural members exposed to atmosphere make or brand IPNET of Krishna Conchem or New Coat from Dr. Fixit complete all as specified.

M&L for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes. Works shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun.Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min.12 hrs. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements. (iv) In case crack upto 2mm wide, fix the injection nozzels directly over the cracks, at intervals of 6 to 9 inches, using a drilling machine. Fix PVC/MS nozzels in these holes with fast-setting epoxy putty & let it dry for 2 to 3 days. Also, seal the crack between the ports with epoxy putty. (v) In case where the crack is wider than 2mm upto 4 to 5mm, drill holes at the sides of the crack in a staggered fashion, at intervals of 6 inches and affix them with epoxy putty as mentioned above. (vi) Also, seal the face of the crack with a liberal application of the epoxy putty.

M&L for Injecting of site mixed cement slurry grout, mixed in specified proportion containing cement, sand water with addition of plasticizers (approved make) & migratory corrosion inhibitors, water cement ratio shall be varied between 0.5 to 1.0 for each hole, shrinkage compensating cement slurry mixed to a lump free fresh creamy consistency ,Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 3-5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled. Make / brand of Epoxy grout - Dr. Fixit Epoxy injection or EPCO KP-HP-250 of M/s Krishna Conchem or Shaligrout EI of STP Ltd.

M&L for Injecting low viscosity (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, Including,Mixing of materialas:Mixing of material components(part a&b) in the required quantities as per manufacturer's instruction by weigh batching.Grouting:Fill the grouting gun with concrete penetrating corrosion inhibitor EPCO-KP-100/Protectsil CIT or Ferogard 903. Maintain desired pressure in the gun by air compressor; maintain the pressureat exit(2 to 3kg/cm2) by monitoring pressure guage at exit.Grout the material through prefixed nozzles in the structural elements@ 100ml per nozzle. Repeat the process for all the nozzles.

Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified and directed.

Providing and fixing additional main steel bar or stirrups of designed diameter in various structural elements like column ,beams and foundations including drilling ,bending, welding and fixing the bars with epoxy putty etc. complete (Steel provided on the basis of 1% of volume of concrete).

M&L for Providing and applying jacketing around columns with Micro concrete (Molith-MC) M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete.Note: Reinforcement shall be measured and paid separately.(Rates including jacketing, formwork and micro concrete)

Demolition of brick work or stone boulded masonry built in cement mortar or cement lime mortar complete all as specified and as directed.

M & L for preparation of new or previously untreated plastered surfaces of walls and applying two coats of acrylic antifungal paint exterior grade paint over one coat of primer complete all as specified and as directed

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper of any colour or tint. complete all as specified and directed by Engineer-in-Charge.(Note:- Item rate shall be include any height of Bldgs / Hangars for scafolding as all arrangement.)

M&L Preparation of old white washed surfaces of ceiling (plastered or unplastered) for white washing and applying one coat of white wash complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L PCC 1:2:4 type B2, using (40 mm graded agg) ,100 mm thick as in flooring with an admixture of metallic floor hardner 3% by weight of cement ( Metallic floor hardner to be measured and paid separately) complete all as specified and directed.

Supply only metallic floor hardner

S&F glass dividing strip 3 mm thick and inserted in position to conform to design 38mm wide complete all as specified and directed.

M&L plain cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

Demolition of cement concrete (unreinforced) roof or chajja padding of any description and any position not otherwise specifically provided for complete all as specified and directed.

M & L PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in roof/chajja padding/coving for maintaining roof/chajja minimum slope 1:6 complete all as specified and as directed

Surface preparation : Complete removal of existing water proofing treatment of any description and in any position including cleaning, wire brushing, watering, removal of debris upto 1500 mtr distance. Clean the surface thoroughly using mechanical tools and the surface to be free of dirt, oil. Repair all cracks by cutting "V" groove and fill the gap using repair mortar Fibre Reinforced Polymer Provide 75mmx 75mm Coving / angle fillet using the above repair mortar using Latex Based Bonding Agent as bond coat. All construction joints to opened 15mmx15mm and treated with repair mortar Fibre Reinforced Polymer and Honeycombing to be pressure grouting with No Shrink cementatious Injection Grout. Water Proofing Application : The surface to be free from standing water Prime the surafce with UV stable Polyurethane water proof liquid membrane at 400gm/sqmt dilute with water 1:1 Apply 1st coat of ShaliPrime WP WB at 400gm / Sqmt. Apply 1st coat of UV stable Polyurethane water proof liquid membrane White at 1Kg/Sqmt. Place 40 Gsm Geotextile / FG Tissue as reinforcement followed by 2nd coat of UV stable Polyurethane water proof liquid membrane at 1kg/sqmt. Ensure final curing of 36hrs before carrying any further work. Extend water proofing treatment and terminate at the top of the edge of the parapet wall Seal the Groove using repair mortar. Note : In case of foot traffic for maintennace purpose a separate walkway of 1m to be made with 40mm interlocking tile over Geotextile Make : (i) ShaliUrethane BTD of M/s STP Limilted (ii) Sec-I PU500 of M/s SG Corporation (iii) Impermo 3002 of M/s Pratham Enterprises (iv) Opty D5HDPU of M/s Optimus Chemicals

M&L for rendering 10mm thick cement plaster in CM (1:3) on roof top surface including WPC by weight of 3% of total cement content complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 sqm not exceeding 4.0 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

S&F Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F in repair rolling shutter without ball bearing, thickness of laths 1.25mm as specified including top cover, anchoring rod,helical spring, hasp and staple, and one shop coat of primer; erected in position as indicated, complete, gear operated type with bevel gear box and crank handle.

Extra for wicket door including 4 lever mild steel safety lock lockable from both inside and outside (area of wicket door to be measured)

M&L for preparing new or previously untreated steel surface of any decription over 10cm in width or girth and applying 2 coats of aluminium paint over one coat of red oxide primer complete all as specified and directed.

M&L for brushing neat cement slurry with 3Kg of cement per square metre all as specified and directed.

Demolition of reinforced cement concrete (Reinforcement cut as required to facilitate deomolitions) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling of stone slabs & tiles of any description or thickness in floor aprons, cills etc laid bedded & pointed in any mortar complete all as specified and directed.

S&F Granite tile of 20mm thick vertical surfaces such as skirting/dado, machine cut bedded and jointed with grey white cement slurry and pointed with white cement with add mixture of pigment to match the shade of granite stone including cutting and polishing including 10mm thick screed bed or bedding layer of mortar in CM 1:4 for laying in vertical surfaces complete all as specified and directed.

M&L for green marble 20 mm thick machine cut in skirting / dado,window sill, laid over cement screed, jointing and pointing with white cement slurry complete all as specified and directed.

Demolition of pre-cast concrete block, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks in 10cm in width in type B1 (1:2:4) and setting in mortar (1:6) complete all as specified and as directed.

M&L for preparation of old wall surfaces of any description & applying one coat of acrylic (antifungal) exterior grade paint of camouflage pattern complete all as specified and directed.

M&L for preparation of old painted surfaces of wood or wood based surfaces over 10 cms width or girth and applying one finishing coat of synthetic enamel paint on wooden surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified.

Taking down of shutters of any description n exc 1 sqm each including iron mongrey & removing from site complete all as specified and directed by Engr-in-charge.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each including iron mongrey & removing from site complete all as specified and directed by Engr-in-charge.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each including iron mongrey & refixing in same opening complete all as specified and directed by Engr-in-charge.

S & F 2nd class hard wood plain solid straight chowkats and frame of wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S & F 30mm thick second class hard wood plain, framed,panelled shutters(any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

Cutting holes in brick wall for inserting holdfast and making good dismantled portion by filling PCC (1:2:4) type B-1 exc. half brick but n.exc one brick incl existing surface finishes complete all as specified and as directed.

S&F mild steel work, Grade Fe-410-0 or Fe- 310-0, as in flat iron (for holdfast) complete all as specified and as directed.

S&F for concealed star lock powder coated for aluminium window fixed as per manufacturers instructions complete all as specified & as directed.

S&F for aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S&F for rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors etc complete all as specified and as directed.

S & F in repair floor door stopper of Aluminium alloy body and tongue, over all length of cover plate 150mm anodised with hard drawn steel spring, fixed to shutters complete all as specified and as directed.

S & F in repairs Mortice lock vertical type size 100mm brass 04 levers complete all as specified and as directed.

S & F for Pre-laminated 18/19 mm thick partilcle baords, exterior grade, prelaminated both sides with decorative choice lamiantions complete all as specified and as directed.

S&F Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 250 mm complete all as specified and as directed.

Taking up or down steel tubing and connections 15 mm bore complete all as specified.

Taking up or down steel tubing and connections 20 mm bore complete all as specified.

Dismantling of water tank capacity exc 1000 ltrs and n.exc 2000 ltrs and removing to store all as specified in SSR Part I complete all as specified.

S&F rotational moulded polythene water storage tank of 2000 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified.

S & F in repairs Bib tap15mm dia standard of CP any colour screwd for iron pipes and fixed (minimum weight 15mm - 90 gms ) complete all as specified.

S & F in repairs stop valve of CP any colour high presure screwd for iron pipes and fixed (minimum weight 15mm - 90 gms ) complete all as specified.

S&F in repairs brass CP shower rose 125mm size complete all as specified and directed.

Dismantling structural steel work including doors, gates,grills but excluding framed truss etc. complete all as specified and directed.

S & F for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F 0.80 mm thick Mild steel, plain, blacksheet in wall cladding,steel gates and similar work, cut to size, holespunched; includinground headed screws,clout nails or rivets and fixed /welded to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc complete all as specified and as directed.

M&L Preparation of new previously untreated steel and iron surfaces of any description not other wise described over 10 centimetre width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc, removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified.

Excavation over area, n.exc 1.5m deep & getting out in soft/loose soil. Complete all as specified directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sure ping clean & washing down with water to remove dust etc

S&F 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 75mm bore PVC(SWR) bends any radius complete all as directed.

Taking down carefully copper /aluminium point wiring (light, fan socket or power) through PVC casing caping including complete fittings such as switches, ceiling roses, pendants, regulators, sockets, buzzer, bell, switch sockets, electrical fittings etc removing and making good disturbed surfaces of walls/ceiling etc, all as specified and directed.

Point wiring with single core 1100 volts grade 1.5 sqmm size FRLS PVC insulated unsheathed stranded copper conductor cable using color code drawn through PVC conduit & including laying of PVC conduit 25mm dia concealed on wall surface with all accessories Complete all as specified in and including sunk type pressed steel/CI terminal box with 3mm thick hylam Mansonite sheet top cover / PVC Board including 1.5 Sq mm FRLS PVC insulated unsheathed copper conductor cable for continous earth conductor (using green colour) to common earth and connecting to earth dolly for the following

One light /fan/ call bell point controlled by one switch.

One 5 pin socket outlet 5 Amps on independent board .

One light point controlled by 2 way switch SP, 5 Amp, 240 Volts

One 5 pin socket outlet 5 Amps on same board

Ditto, all as per sl item No 163.00 hereinbefore, but using 2.5 sqmm ( nominal area) multistranded FRLS copper conductor cable/wire & 1.5 sqmm size PVC insulated unsheathed copper conductor cable for earth continuity ( green colour) for one 5 pin socket outlet 5 / 15 Amp multi purpose independent point controlled by 15 Amp switch, SP one way, 240 Volts & Socket, complete all as specified and directed.

Supply and fixing switch piano type flush button type single pole one way 5 Amps 240V front operated complete all as directed.

S&F Switch socket combination 2 in 1 3 pin, 5 A and 15Amp flush type universal complete all as directed.

S&F Switch socket combination 2 in 1 3 pin 5 A flush type complete all as directed.

S&F socket outlet 2 in 1, 5 Amp, surface type complete all as directed.

S & F switch socket outlet 15 Amp, 5-in-1, controlled by one switch (ISI marked) all as per Cat No 14615 of M/s Anchor Penta or equivalent complete all as specified and directed by Engineer-in-Charge.

S & F switch flush button, single pole two way, 6 Amp (ISI marked) complete as per Cat No 50020 of Anchor Penta or equivalent of makes BEC/Havells complete all as specified and directed by Engineer-in-Charge

S & F socket type EME fan 5 step regulator for ceiling fan metallic frame and copper plates of suitable size, complete all as specified and directed by Engineer-in-Charge.

S & F modular switch single pole one way, 6 Amp, 1 module (ISI marked) complete all as specified and directed by Engineer-in-Charge

S & F modular socket 6A -2/3 pin combined 2 module (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S & F modular socket 6A/16A -2/3 pin combined 2 module (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S & F modular switch single pole one way, 16 Amp, 1 module (ISI marked) complete all as specified and directed by Engineer-in-Charge

S & F modular white cover plate with frame, 1 module (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S & F modular white cover plate with frame, 3 module (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S & F modular white cover plate with frame, 4 module (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S & F modular white cover plate with frame, 6 module (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S & F modular metal flush box 1/2 module, complete all as specified and directed by Engr-in-Charge.

S & F modular metal flush box 3 module, complete all as specified and directed by Engr-in-Charge.

S & F modular metal flush box 4 module, complete all as specified and directed by Engr-in-Charge.

S & F modular metal flush box 6 module, complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose PVC/polycarbonate, isolated body surface Bakelite 65mm dia three terminals complete all as directed.

Supply and fix LED batten with 18W LED tube light in wall/surface connecting with all required accessories like flexible cable from ceiling rose etc as directed and specified by engr-in-charge.

S & F LED batten with tubelight 10W 2 feet in wall/surface connecting with all required accessories like flexible cable from ceiling rose etc as directed and specified by engr-in-charge.

S & F replacement MCB TPN 415 Volts, 50 Hz, 10 KA conforming to IS-8828 of rating 40 to 63 Amp complete all as specified and directed by Engineer-in-Charge. Make: Legrand/Havells/L&T

S & F replacement MCB distribution board TPN, 4 ways, 415 Volts, 50 Hz, AC, double door made out of sheet metal phosphatised and painted with epoxy polyster based powder paints with 200 Amps rated bus bar and earth bar, ISI marked complete all as specified.

S&F double door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 4 way double door open able, including taking out old unsv MCB DB any size/type.

S&F single door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 2 way single door open able, including taking out old unsv MCB DB any size/type.

S & F replacement MCCB distribution board VTPN, 4 ways, 415 Volts, 50 Hz, AC, double door made out of sheet metal phosphatised and painted with epoxy polyster based powder paints with 200 Amps rated bus bar and earth bar, ISI marked complete all as specified.

S&F 6 to 32 AMP MCB single pole 240 V 10 KA (C-Series) complete all as directed.

S&F MCB SPN 32 AMP 240 volts AC (C -Series) complete all as specified and directed.

S&F MCB TPN 63 AMP 240 volts AC (C -Series) complete all as specified and directed.

S&F MCCB 3 pole 80 Amps, 415 volts, 50 hz complete all as directed.

S & F replacement MCB SPN 240 V, 50 Hz, 10 KA conforming to IS 8828 of rating 6 to 32 Amp 'C' series complete all as specified and directed by Engineer-in-Charge.Make: Legrand/Havells/L&T

S & F replacement MCB DB, SPN, 8 way, 230 Volts as per IP-42 of complete all as specified and directed by Engineer-in-Charge. Make: Legrand/Havells/L&T

M&L for wiring for circuits/sub main wiring with FRLS PVC insulate sheathed 2 x 6 sqmm stranded copper conductor cable 1100 volts grade heavy duty drawn into PVC conduit concealed with 6 sqmm PVC insulated green copper cable for continues earth PVC pipe not less than 25 mm dia with all accessories complete

Supply, fixing, stringing and drawing submain wiring with 2 run of single core 4 Sqmm PVC insulated and unsheathed, multi stranded FRLS copper conductor cable using colour code for phase red and neutral black with and including 4 Sqmm PVC insulated and unsheathed copper conductor multistranded cable in green colour connected to common earth point and connected to earth dolly drawn through 20 mm PVC conduit conceal on wall, heavy grade (ISI marked) with and including all accessories etc in replacement compete all as specified and directed NOTE:- (i) Two run of 4 sqmm, one run of 4 sqmm earth continuity conductor and 20 mm PVC conduit conceali on wall and accessories shall be measured and paid as one length. (ii) Cable shall be of ISI marked of make M/s Finolex / M/s Plaza /M/s Havells (iii) PVC conduit shall be makes given in Appx 'A' to PS.

M&L for earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead wire 4.0 mm dia means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including testing on completion. NOTES : The unit rate includes for protection pipe and lead wire from top of earth plate up to 7.5 meter above ground level.

Supply and fixing LED building security light fitting with suitable size bracket/angle to fit security light of 45w IP 66 protection LED make bajaj ct pt no-BRTFG 45 Watt complete all as directed.

Supply and fix LED bulk head 10W in wall/surface for mirror light connecting with all required accessories like flexible cable from ceiling rose etc as directed and specified by engr-in-charge. Make: Havells ct pt no LHEOAOP7UZ6W010 or equivalent in CG/C&S/bajaj.

Taking down old unserviceable 2 core 6 Sqmm XLPE/PVC insulated PVC sheathed cable heavy duty 1100 volts grade, aluminium conductor complete all as directed.

Supply & fixing XLPE/PVC insulated PVC sheathed cable heavy duty 1100 volts grade, aluminum conductor in trenches / ducts of size 2 core 6 Sqmm and including necessary arrangement of saddle the cable on wall complete and all as specified and directed by Engineer-in-charge.

S & F LED suspension tube light type light 36w including making arrangements for hanging the fitting of cat no-DESTELLO70LP/S36WLED857SPMMAWH of HAVELLS or equivalent in PHILIPS /CG complete with all accessories as directed and specified by Engr-in-charge.

S & F wall light fixtures made up of polycarbonate, suitatable for and including 5 watt LED bulb fixed on wall complete all as specified and directed. Make/Model : Havells/LHFODFE1TC1W015 or equivalent of Philips/Wipro.

Supply and fixing Non- Metallic exhaust fan single phase 250mm sweep. Make Havells Ventilair DXWHT/BLK or Orient 200 mm or 8” Ventilation Raffa including all connected accessories and making necessary cutting and chasing to make holes on wall to fix the fans as directed and specified by Engr-in-charge.

Supply and fix wall mounted fan 450mm sweep as directed and specified by Engr-in-charge.

Taking down ceiling fan/exhaust/wall fan including flame proof exhaust fan and keeping in safe custody for refixing the same after duly painted and necessary repair work like greesing work etc complete all as specified and directed by engr-in-charge.

Refixing the ceiling fan/wall fan/exhaust fan taken down against item above and connecting with the ceiling rose with proper size flexible black colour copper wire complete all as specified and directed by engr-in-charge.

BALAJI TRADERS