Completion of Community Hall at Goan alongwith side room at Phyang

Amount

Providing and fixing UV stabilised fibreglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated 'J' or 'l' hooks, bolts and nuts 8mm dia. G.l plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-voilet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2mrm, thick corrugated (2. 5" or 4.2" or 6") or stepdown (2" or 3" or 6") as specified.

Steel work in built up tubular round, square or rectangular including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer including welding and bolting with special shaped washers etc.complete.

Earthwork in rough excavation banking excavated earth in layer not exceeding 20cm in depth banking clods watery rolling layer led upto 50meters and lift upto 1.5meters.

Providing and laying dry stone soling in horizontal including cost of stone.

Providing and fixing aluminium work for doors, windows,ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.) Anodised aluminium (anodised transparent or lyed to required shade according to IS: 1868, kg 428.25 minimum anodic coating of grade AC 15).

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.)With float glass panes of 5.50 mm thickness (weight not less than 13.50 kg/sqm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminium round shape handle of outer dia 1 OOmm with SS screws etc. Complete as per direction of Engineer-in-charge.Powder coated minimum thickness 50 micron aluminium.

Providing and fixing tower bolt barrel type aluminium ISI marked (Doors)

Providing and fixing tower bolt barrel type aluminium ISI marked (Windows)

Providing, fixing and applying plaster of paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab including providing and fixing expanded metal of size 5.25mmx1.25mm thickness welded to main runner and applying POP (calcium sulphate semihydrate variety)to the expanded metal of thickness not less than 10mm finished smooth to line and level including necessary supports scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. fiame work and suspenders complete.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position Budloo wood .

Providing and laying Mud Concrete under wooden flooring with 4mm nominal size stone aggregates.

Providing and fixing 1.5 thick wooden plank for flooring with T&G including cost of wood, lobour and complete job using Budloo wood.

Carriage of stone from an average lead of 5kms by MT.

Carriage of steel from an average lead of 25kms by MT

m/s banaras steel fabrication

M/S RIGZEN TSEWANG GOVT CONTRACTOR

M/S JIGMAT DORJAY