PROVISION OF HARDSTANDING AT PARKING AREA OF CERTAIN UNIT AT SARAIBARI, SPECIAL REPAIRS TO BLDG No. P 15 P20 OF CERTAIN UNIT AT SARAIBARI, SPECIAL REPAIRS TO ROOF SHEET IN BLDG No P-14,P-24,P-32,P-36 CLOTHING STORE OF CERTAIN UNIT AT SARAIBARI AND

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Dismantling timber fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section, in unframed work,complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling mild steel work in roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and including erection, refixing in same position,complete all as specified and directed.

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings,complete all as directed.

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings, and refixing in same position with self tapping screws,complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Dismantling water tanks of capacity exceeding 250 litres & not exceeding 500 litres and removing to store for taking credit,complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking down SWR pipes (any size or pattern), including all fittings, 'T', bends,etc., including removal to store for taking credit (measured overall as fixed along the centre line over fittings and accessories), complete all as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Materials and Labour for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Materials and Labour for plain cement concrete (1:5:10) Type E-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6), Type C1,using 20mm graded aggregate in filling of pressed steel chowkhat complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for reinforced cement concrete 1: 2 :4, Type B1 (using 20 mm graded aggregated) in beams, cantilever, bressumers, lintels over 1.5M Span,complete all as specified and directed.

Materials and Labour for reinforced cement concrete 1: 2 :4, Type B1(using 20 mm graded aggregated) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like,,complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Materials and Labour Extra for forming fair finishing to surfaces channels/drain 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, etc complete all as specified and directed.

Supply only integral water proofing compound all as specified

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in built in CM (1:4),complete all as specified and directed.

Materials and Labour for,cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, in stone concrete block or slab walls, complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Supply and Fix, second-class hard wood timber scantlings, clean sawn, in unframed works and in any position, fixed with nails complete all as specified and directed.

Supply and Fix, 35 mm thick, flush shutters, solid core construction, with particle board core and plywood face panels,both faces is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 100 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet sections. The inside section of size 90mm x 30 mm shall be made from colour PVC sheet of 5 mm thickness.The inside section shall be covered by sticking two sections of size 35mm and 6 x 45 mm made from 5mm thick plain sheet. The frame shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 04 Nos. of screws shall be provided for each vertical member and minimum 02 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2 mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and Fix, extruded aluminium alloy handles, fabricated type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, brass chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, including taking down existing one complete all as specified and directed.Make Cat no.AKP 35711P of Jaquar or equivalent of Marc/Kohler

Supply and Fix, in repair decorative drapery curtain rod 25 mm dia chromium plated with including fancy side ,brackets complete all as specified and directed.

Supply and Fix, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and with overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed.

Supply and Fix, mild steel, 300 mm, ordinary rat-tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 6 to 8 mm dia., cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 5 mm dia. and over up to and including 10 mm dia. in stirrups, spacers, binders etc. cut to length, bend to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

Supply and Fix, mild steel screw bolts (machine made), with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, diameter of shank 11 to 15 mm, length of bolt n. exc. 5 long, complete all as specified and directed.

Materials and Labour for mild steel works, conforming to Fe 290, Grade E-165 , in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, complete all as specified and directed.

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Materials and Labour for rolled mild steel,Fe 410-W (Grade E-250) Quality-A in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed.

Materials and Labour for rolled mild steel , conforming to Fe 410-W (Grade E-250) quality-A, as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guide for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

Supply and Fix, pressed steel frames, size 125 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete without glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and Fix, aluminium frame with powder coating of any colour (Thickness of powder coating not less than 50 micron), 100 mm x 45.5 mm x 1.5 mm thick for with one or more rebates including joining cleat for fixing etc.,aluminium with powder coating of any colour (Thickness of powder coating not less than 50 micron) powder coating of any colour (Thickness of powder coating not less than 50 micron) glazed shutters (single/double) fixed/openeable/partition, divided into two parts,with top,bottom & mid/lock rail sections 100 mm x 44 mm x 1.5 mm and styles sections 100 mm x 45.5 mm x 1.5 mm including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.,with and including 5 mm thick tinted glass, complete all as specified and directed.

Supply and Fix, aluminium frame with powder coating of any colour (Thickness of powder coating not less than 50 micron), 63 mm x 47 mm for sliding windows with one or more rebates including joining cleat for fixing etc., with sliding type shutters,without sash bars, aluminium sections with powder coating of any colour (Thickness of powder coating not less than 50 micron) 39 mm x 18 mm including necessary joining cleats, glazing clips, rubber packing, aluminium with powder coating of any colour (Thickness of powder coating not less than 50 micron) snap beading, screws etc.(Thickness of aluminium sections not less than 1.5 mm),with suitable sliding & locking arrangement, anodised aluminium grill 7.1 mm thick, weighing 2.701 Kg/Sq M,stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and 4 mm thick tinted glass, complete all as specified and directed.

Supply and Fix, aluminium frame with powder coating of any colour (Thickness of powder coating not less than 50 micron),for sliding windows with one or more rebates including joining cleat for fixing etc., with sliding type shutters,without sash bars, aluminium sections with powder coating of any colour (Thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, aluminium with powder coating of any colour (Thickness of powder coating not less than 50 micron) snap beading, screws etc.(Thickness of aluminium sections not less than 1.5 mm),with including suitable sliding & locking arrangement, and anodised aluminium grill 10mm thick as per section.7733 of Hindalco, complete all as specified and directed. Notes:- (i) Sheet glass and wire cloth will be measured and paid seperately under respective items of this BOQ. (ii) The quoted rate against this item shall be deemed to be inclusive of the rate for taking down existing shutters.( iii) Weight per RM of aluiminuim section will be checked by BOO as assembled by AO

Supply and Fix, 0.80 mm thick, plain, galvanised, mild steel sheeting in stepped flashings (measured as the minimum rectangle from which the pieces can be cut),grade of coating 275, with minimum zinc coating of 275 gms. /Sq m,complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.60 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata blue scope or equivalent make as approved by GE)

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.60 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata blue scope or equivalent make as approved by GE)

Materials and Labour for exposed metal frame ceiling with 6mm thick high pressure steam cured (HPSC) non asbestos fibre reinforced cement designer building boards for fixing in 600 mm x 600mm grid with and including exposed metal frame using hot dip galvanised steel, exposed pre-coated ceiling suspension system of grid size 600 mm X 600 mm, with main runner ‘T’ section 24 mm (W) X 38 mm (H) X 0.40 mm (T), cross ‘T’ section 24 mm (W) X 28 mm (H) X 0.30 mm (T) , wall angle 24 mm X 24 mm X 0.43 mm (T) and suspended with 4 mm dia. GI hangers/ wire fixed with steel dash fasteners from purlins/soffits spaced at 1200 mm centre to centre with butterfly clips, hold down clips, providing provisions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc., complete all as specified and directed.

Materials and Labour for 40 mm thick plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates as in sub base of floor,complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement complete all as specified and directed.

Filling joints in plinth protection, 30 mm deep x 10 mm wide, filled solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and MAKE:- (Johnson/Kajaria or equivalent make ) directed.

Materials and Labour for, digital ceramic coloured tiles, 450 X 300 X 7 mm thick, conforming to ISO 13006, EN 14411 , Group B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match with over and including 10mm thick rendering complete all as specified and directed. MAKE:- (Johnson/Regency/Kajaria)

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for Digital Vitrified Ceramic Tiles,, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Material and Labour for chequered finish heavy duty industrial ceramic tiles, coloured, 12 mm thick (square/ rectangular) area of each tile exceeding 0.07 Sq M but not exceeding 0.18 Sq M, conforming to IS 4457-2007, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour including 15mm thick screed bed in cement mortar (1:4),complete all as specified and directed. MAKE:- (Johnson ‘Endura’ or equivalent make Somany ‘Durastone’/ Regency ‘Duro’)

Materials and Labour for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Materials and Labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15mm thick rendering complete all as specified and directed.

Material and Labour for Machine Pressed Precast Concrete Interlocking Paver Block ,with grey cement and pigment, any shape and size conforming to IS 15658-2006, of 80 mm thickness, M-40 Grade,laid on pavements, complete all as specified and directed.

Materials and Labour for 150 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base/paving/hardstanding , complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Material and Labour for applying three coats of white wash to new plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Materials and Labour for applying applying two coats of oil bound distemper, white or tinted, to new plastered surfaces on walls, over and including 3mm thick wall care putty premium quality over priming with alkali resistant priming paint and including preparation of surfaces, complete all as specified and directed.

Material and Labour for complete removal of existing treatment and applying two coats of oil bound distemper,white or tinted over 3mm thick wall care putty, to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

Material and Labour for applying two coats of cement-based paint, white or tinted to new plastered surfaces on walls including priming with alkali resistant priming paint and including preparation of surfaces complete all as specified and directed.

Material and Labour for complete removal of existing treatment and applying two coats of cement-based paint, white or tinted to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4.8 mm thick sheet glass, tinted quality and glazing in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Material and Labour for applying one coat of synthetic enamel paint on old painted steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coat of synthetic enamel paint on old painted wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Material and Labour for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete, all as specified and directed.

Materials and Labour for, Ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed complete all as specified and directed.

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed. Make:Cat No.QQT-7037 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.QQT-7053 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Jaquar /Marc/Kohler)

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.QQT-7011 of Jaquar or equivalent make of Marc/Kohler)

Supply and Fix, brass CP fancy wall mixer with L bends (including provision of O/H shower & hand shower) for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed, with including hand shower and tube inlcuding taking out unserviceable existing one complete all as specified and directed. (Make Hand shower cat part no. HSH-CHR-1717 and wall mixer cat part no. QQT-7281 of Jaquar or equivalent make Kohler/Marc)

Supply and Fix, in repairs under counter basin vitreous China wash basin, white, oval shape Size 425mmX550mmX195mm with and including rawl plug and screws),32 mm nominal size copper alloy ;nickel chromium plated finish waste fittings sealing gap between wall and basin with silicone sealent ,cutting and making goods as per existing specification with and including connecting to supply pipes, waste pipes waste fittings et cincluding taking out unservieable existing one complete all as specified and directed.(Make Cat part no.FLS-IVY-5701 of Jaquar or equivalent make of Kohler

Supply and Fix vitreous China wash down water closet pan (pedestal pattern), white, (including fixing bolts, flushing cistern and flush pipe connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc.including taking out di of existing one and making good disturbed surfaces as per existing specification complete all as specified and directed. Make Hindware Catpart no.92053 or equivalent make of Kohler/Jaquar

Supply and Fix vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding, complete all as specified and directed. (Make Cat part no.20042 of Hindware or equivalent make of parryware/Cera

Materials and Labour for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix,in repair plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed.

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Supply and Fix in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. Make Cat no. CAN-CHR-1171N of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, waste coupling of PTMT (half or full threaded) (Minimum weight 45gms), for 32 mm bore discharge pipe,complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, stack clamps for 100 mm bore pipe, made out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof,complete all as specified and directed.

Supply and Fix, 50 mm bore, low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.

Supply and Fix, in repairs 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix, 110 mm bore PVC (SWR) bends any radius,complete all as specified and directed.

Supply and Fix, 110 mm bore, PVC (SWR) junction single, (Single T) equal or unequal, with access door,complete all as specified and directed.

Supply and Fix, in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix, PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

Material and Labour for, 150 mm spread thickness,soling (or sub base) with broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated to required gradient and camber, complete all as specified and directed.

Rolling and consolidating soling of broken boulders or quarried stone, not exc 15cm thickness with power roller exceeding 8 tonne and not exceeding 12 tonne, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Materials and Labour for point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for, one light point or one fan point controlled by one switch, complete all as specified and directed.

Materials and Labour for point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for, one 3 pin socket outlet, 5 Amps on the same board with other switches,complete all as specified and directed.

Materials and Labour for point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switch/socket outlet etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for one 3 pin socket outlet, 5 amps, independent,, complete all as specified and directed.

Materials and Labour for point wiring with 4.00 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switch/socket outlet etc and including 2.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for one 3 pin socket outlet, 15 amps, independent,, complete all as specified and directed.

Materials and Labour for two single core FRLSH PVC insulated unsheathed cable 6.00 Sq. mm. (Nominal area) with stranded copper conductor cable, 1100 Volts grade, drawn in PVC Casing and Capping and continuous earth wire of single core FRLHS PVC insulated, unsheathed cable 4.00 Sq. mm (nominal area) with stranded copper conductor cable, 1100 Volts grade for sub main wiring, complete all as specified and directed.

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, switch piano, flush button, single pole, one way, 15 Amps, complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, socket outlet 2 in 1, 3 pin, 5A, complete all as specified and directed.

Supply and Fix, switch socket combination, 2 in 1, 5 Amp, flush type , complete all as specified and directed.

Supply and Fix, switch socket combination 2 in 1, 5 pin, 15 Amp, flush type universal, complete all as specified and directed.

Supply and Fix, socket outlet 2 in 1, 6 pin, 5 and 15 amp flush type, complete all as specified and directed.

Supply and Fix, LED lamp, 10 Watts, lumen output 1100 lm, colour temp 6500 K, lamp current 0.055 amp, lamp base cap B22, complete all as specified and directed.

Supply and Fix, decorative LED tube light fitting with extruded polycarbonate housing,18 Watts,colour temp 6000 K, all as per Cat No. LHEXBHP7IN1W018 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Supply and Fix,18 Watts, LED down light, recess mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver and diffused optics,colour temp 6000 K, all as per Cat No. LHEBJNP7PZ1W018 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips suitable for ceiling cutout Ø 160 mm, height 55 mm,complete all as specified and directed.

Supply and Fix, LED roadway luminaire, 25 Watts, with pressure die-cast aluminium housing,IP-66, high power LEDs as light source and electronic driver, all as per Cat No. LR02-291-XXX-57-XX of Make ‘Wipro’ or Equivalent Model of Make Havells/Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.75 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Supply and Fix, LED roadway luminaire, 35 Watts, with pressure die-cast aluminium housing,IP-66, high power LEDs as light source and electronic driver, all as per Cat No. LR02-391-XXX-57-XX of Make ‘Wipro’ or Equivalent Model of Make Havells/Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.75 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar or cement lime mortar, for exhaust fan and other openings or enlarging existing openings,superficial area exceeding 0.16 Sqm but not exceeding 0.25 Sqm, making good distrubed portion, grouting of suitable bolts with nuts & washers for fixing exhaust fan,rendering 15 mm thick plaster in CM (1:4) around jambs of opening, complete all as specified and directed.

Supply and Fix, Heavy Duty Exhaust Fan, 300 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan including dismantling of existing unserviceable one complete all as specified and directed

Supply and Fix, Heavy Duty Exhaust Fan, 380 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan including dismantling of existing unserviceable one complete all as specified and directed.

Materials and Labour for,painting of ceiling/Exhaust fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc., including minor repair as replacement of wiring , capacitor complete all as specified and directed.

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 6 way, with 200 Amps rated bus bar, Single Pole & Neutral, including dismantling taking down unserv. DB complete all as specified and directed. [Cat No.DBSPN006DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 8 way, with 200 Amps rated bus bar, Single Pole & Neutral, including dismantling taking down unserv. DB complete all as specified and directed [Cat No.DBSPN008DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 415 Volts, 4 way, with 200 Amps rated bus bar, Triple Pole & Neutral, including dismantling taking down unserv. DB complete all as specified and directed [Cat No.DBTPE004DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs) three pole and neutral, 415 Volts, 10KA, 63 Amps complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 35 sq. mm, 3 ½ core, including with suitable size of lugs complete all as specified and directed.

Supply and Laying galvanized steel tubing, 40 mm bore, light grade, in trenches or fixed to poles/Walls etc., for cable protection, complete all as specified and directed.

Supply and filling in dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and directed.

Supply and laying common burnt clay building bricks, sub-class ‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

M/S GOPAL ROY AND CO

yadav construation

M/S RK SAHA AND CO