PETTY REPAIR TO CERTAIN BUILDINGS, ROOF TREATMENT, ROOF SHEETING ETC AND REPAIR TO MES INSTALLATION (W/S) AT MENDHAR, BG HAMIRPUR IN THE AOR OF IN THE AOR OF AGE B/R-I UNDER GE 881 EWS

Amount

M&L for roughening of of old concrete floor by picking, sweeping, cleaning by using steel wire brush and washing down with water, fanning dust etc and taking down tarfelt/cement plaster and removing demolished material to a distance exc 50 m, complete incl dismantling existing lightening conductor and refixing in same location incl repair/replacement if not working after completion of roof treatment, complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in roof padding, complete all as specified and directed.

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:3) with mixing of water proofing compound @ 200ml/50 kg of cement in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane and finished the surfaces even and smooth without using extra cement, complete all as specified and as directed. (NOTE : Polymeric membrane & WPC shall be measured and paid separately under relevant item of this Schedule 'A').

M&L for applying a tack coat of industrial bitumen of grade 85/25 @ 1.2 kg/sqm including cleaning the surface, complete all as specified and directed.

M&L for preparation of surface by applying bituminous primer (conforming to IS-3384-1965) @ 0.4 kg/sqm and applying heavy treatment (for severe conditions), APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application and applying a coat of aluminium paint over APP membrane complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of capacity exc 250 ltr but not exc 500 ltr capacity, complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position of capacity exc 500 ltr but not exc 1000 ltr capacity, complete all as specified and as directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but n.exc 4 Sqm (without taking off shutters from frame), complete all as specified and direcetd.

Dismantling boarding, any description, fixed in any position with screws with nails, complete all as specified and direcetd.

Refixing in same opening, chowkhats or frames with shutters not exc 1.5 Sqm (without taking off shutters from frame), complete all as specified and direcetd.

Resecuring without taking down chowkhats or frames exc 1.5 sqm but not exc 4 Sqm with shutters (without taking off shutters from frame), complete all as specified and direcetd.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Supplying and installing vanishing Blinds with Vinyl coated fibreglass fabric laminated with two-ply 100% PVC blackout film (of Revolving Blackout Type and grade 2000 series with RB-07 of SD Blinds make or equivalent make and having same colour, shade and texture). Fire classification of fabric NFPA 701-2004 (small scale), BS 5768-2008 Part 2 Type B Performance Fabric should be Bacterial & Fungus fee, Green guard & Lead free, normal thickness of fabric shall be 0.50mm and minimum weight 255gsm, excellent hanging properties and very high tear strength. The fabric shall be suspended from the top channel made of extruded alloy of 1.25mm nominal thickness and 38mm nominal diameter. The top channel shall be fixed with powder coated mild steel bracket with clutch assembly on either end of blind, fixed to jambs of the window opening with 50 mm stainless steel screw with nylon roll plug and to the aluminium window with 25mm self thread screw. The operating mechanism shall be operated with plastic ball chain having 4.50 mm balls made of ABS plastic linked with 1.50 mm polyester cord. The mechanism shall allow the blind to stop in desired position with the clutch mechanism. The bottom channel shall be made of rectangle shape with extruded aluminium tube with powder coating. The fabric shall be enclosed in suitably created pocket along the tubes, which shall be closed from side with end caps of same colour to the bottom roller. All exposed components of roller blind shall be of milky white colour, complete all as specified and directed.

S&F sheet glass ordinary quality, 5.5mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

M&L for 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement incl using of WPC @ 200 ml/50 kg of cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for 10mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on ceiling surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint on walls complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint on walls (single or camouflage pattern) complete all as specified and directed.

M&L for preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash on ceiling, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

M&L for pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

M&L for rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, cleats etc Fe 410 W(Gde E 250), quality B complete, complete all as specified

M&L for preparation of new or previously untreated steel or iron surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted steel surfaces/CGI/PGI sheets of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling of size 605 x 605mm complete all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for 6 mm thick non asbestos fibre cement building fixed or laid/inserted to timber/GI/aluminium framework fixed in ceiling with screws complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing., complete all as specified and directed.

M&L for PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregate) as in filling holdfast, steel door gframe, coping etc. complete all as specified and directed by Engineer-in-Charge.

S&F Pressed steel frames for doors of size 105 x 60 mm, made out of 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F Pressed steel frames for doors of size 125 x 60 mm, made out of 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L for preparation of new untreated surfaces of steel any description over 10 cms width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F 40 mm thick flush shutters, solid core construction, with b;pckle board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

S&F 35 mm thick 2nd Class hard wood gauged and skeleton shutters, open rebated and prepared to receive gauge etc (with sash bars), edges of framing plain, chamfered or grounded, fitted with cut of and mitred beads for securing gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and as directed.

M&L for two coat of synthetic enamel paint over a coat of pink primer including preparation of new or previously untreated wooden surfaces of any description, over 10cm width or girth, complete, all as specified and directed.

Taking down shutters of area exc 1 Sqm but n.exc 2 Sqm, complete all as specified and direcetd.

S&F Solid PVC moulded door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; Panelling of plain colur PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, Supplied and Fixed in the frame at site as per specification and drawings, complete all as specified and as directed.

S&F in repair stainless steel mild steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm with tinned tacks or galvanised wire stapple, complete all as specified and as directed.

S & F 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and direcetd.

S & F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and direcetd.

S & F 150 mm long aluminium handles, cast type, anodised and fixed, complete all as specified and direcetd.

S & F 300 mm, mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete, complete all as specified and direcetd.

S&F in repair floor door stopper of aluminium alloy body with overall length of cover plate 140 mm and tongue, anodised with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Taking down chowkats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame), complete all as specified and direcetd.

S&F in repair anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F in repair anodised aluminium window and ventilator shutters side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles (350x250mm)/ (450x350mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 with (using 12.50 mm graded crushed stone aggregates) as in sub base of flooring/path/standing complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick screed bed in CM (1:4), complete all as specified and directed.

M&L for Vitrified ceramic tiles 9 to 10mm thick (square/ rectangular), dark shade, polished, area of each tile not exceeding 0.36 sqms et and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for 15mm thick cement plaster rendering in CM 1:4 on other than fair faces of bricks or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of old surface of ceiling and applying two coats of white wash on ceiling, complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F GI tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Taking up or down steel tubing of 20 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F GI tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair 15mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs , including dismantling existing water tank and removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs , including dismantling existing water tank and removing from site complete all as specified and directed.

S&F Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms) complete all as specified and directed.

S&F in repair 20 mm bore ball brass valves high pressure, high pressure with polythene float and fly nuts complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repair 15 mm bore ball brass valves high pressure, high pressure with polythene float and fly nuts complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repair bib tap 15 mm bore, cast copper alloy, chromium plated, fancy tuype with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair stop valves/cock cast copper alloy 15 mm dia, chromium plated with wall flange fancy type with long shank (concealed), screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed.

S&F in repair stop valves/cock cast copper alloy 15 mm dia, chromium plated with wall flange fancy type, screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed.

S&F in repair PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed.

S&F in repair vitreous china wash hand basin counter top, white, of size 580x450 mm excluding tap & plug and porcelain stopper but incl waste brass waste coupling of suitable size, complete all as specified and directed.

M&L for 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified.

S&F in repair vitreous china urinals, half stall type with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repairs PVC waste pipe with union, flexible, 32 mm dia for low level flushing cistern/urinal/WHB etc, complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in trenches or in floor, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches or in floor, complete all as specified and directed.

NATIONAL TRADING COMPANY (BID ID -3298596)

M/s Anil Engineers & Builders (BID ID -3298558)