SPECIAL REPAIR TO BLOCK NO P/116 (08 X QTRS) AT NAR BAHADUR THAPA ENCLAVE AND PROVN OF GARDEN LIGHT AT REAR LAWN OF ENGR BDE OFFICER MESS UNDER GE PANAGARH

Amount

Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc and removing rubbish off the premises complete all as specified and directed.

M&L for Rendering 15 mm thick cement plaster in CM (1:6) on fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) complete all as specified and directed

M&L for Rendering 15 mm thick cement plaster in CM (1:4) on other than fair faces of brick/concrete surfaces finished and smooth without using extra cement and using water proofing compound @ 3% by weight of cement content complete all as specified and directed. Note :- WPC will measured and paid separately under relevant item of schedule.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in CM (1:3) finished even and smooth (without using extra cement) complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed. (Make :Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

Demolition of cement concrete in ground floor & paving n.exc 15 cm thick (below or above ground level) unreinforced removing rubbish off the premises complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for including (reinforcement cut as per required to facilitate demolition) removing rubbish off the premises complete all as specified and directed

M&L for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed

M&L for TMT mild steel bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to complete all as specified and directed

M&L RCC (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed .

M&L for RCC type A1 1:1.5:3 (using 20mm graded stone aggregate) for chajjas and the like complete all as specified and directed

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc surface of concrete flat for rough finished surface of concrete complete all as specified and directed

Use and waste of Formwork to chullah hoods, chajjas, troughs and similar items including edges etc surface of concrete flat for rough finished surface of concrete complete all as specified and directed

M&L for 75mm PCC 1:3:6, type C1 (using 20mm graded stone aggregate) finished the as in plinth protection surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for providing cement concrete type B0, 1:2:4 (using 12.5mm stone graded stone aggregate) as in coping to chajja tops and all other similar works complete all as specified and directed.

M&L for (a) providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry with acrylic based modified cementitaous composite compound coating of make as approved in technical instruction 5/2003 (b) First layer of slurry of cement @ 0.5 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours. (c) second slurry of cement @ 0.500 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (d) 200 micron thick polythene film pasted with the help of bituminous adhesive shall be provided over treatment complete all as specified and directed

S&F as in repair vitreous China squatting pan, 'Orissa pattern' size 580 x 440 mm white, with integral footrests (excluding flushing cistern and flush pipe) including provision of cement concrete complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover complete all as specified and directed

S&F in repair vitreous China wash basin white, flat back, size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed

S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets) complete all as specified and directed Make: Hindware/Parryware/Cera

S&F in repair 15mm bore fancy type stop valve , chromium plated concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair PVC connection 15mm size PTMT nuts of length 600mm complete all as specified and directed

S&F in repair 15mm bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed

S&F as in repair bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F grating square 150mm size of PTMT (minimum 100 gms) complete all as specified and directed

S&F grating square with waste hole 150mm size of PTMT (minimum 100 gms) complete all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x160mm complete all as specified and directed.

S&F as in repair tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as specified and directed

S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack made out of 0.65 mm thick of approved make with plugs, washers, over all size 786mmx610mmx254mm complete all as specified and directed Make : Prayag/Nirali/Hindware

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the primises complete all as specified and directed

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM (1:6) complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed).

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirtings etc. set and jointed in cement slurry over and including 10 mm thick rendering in CM (1:3) complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed).

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM (1:4) complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed).

M&L for Glazed ceramic tiles Coloured 450 x 350mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over and including 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed).

M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite of any type of work complete all as specified and directed.

M&L for 18 to 20 mm thick green marble (table rubbed and polished) in steps, jambs, pillars, window cills,bathroom corners cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified and directed

Rounding to edges of stone slabs exposed edge, such as in steps, cooking platform and other similar situation complete all as specified and directed

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including screed bed or bedding layer of mortar 20mm thick in CM (1:6) for laying floor finish complete all as specified and directed

M&L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item No 40.00 over and including 10mm thick in cement mortar CM (1:3) complete all as specified and directed

Taking down chowkats or frames exc 1.5 sqm but n.exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames) complete all as specified and directed

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk stainless steel screws all as per direction of Engr-in -Charge.

All as per item No 45.00 above but wire gauzed i.e. panel will be of wire gauze in lieu of panel. The wire gauze shall be wrapped on an additional square 8 mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F MS flat iron as in hold fast clamps small articles conforming to FE-290 Gde-E-165 complete all as specified and directed

M&L for PCC (1:2:4) type B-0 as in bed blocks for hold fast including necessary formwork complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed

S&F Prelaminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engr-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, locking arrangement ,C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engr-in-Charge.

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc complete all as specified and directed

S&F 4mm thick sheet glass, ordinary quality and glazing with rubber gasket & aluminium beading in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

S&F for 4mm thick figured glass, pin head type and glazing with rubber gasket in squares n exc 0.5 sq. m in each pane complete all as specified and directed

S&F 100 mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed

S&F aluminium anodised 75 mm barrel tower bolts of extruded section complete all as specified and directed

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 75 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted.

S&F 75 mm long hasp and staple, aluminium anodized with bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F 300 mm mild steel ordinary rat tail rod pattern spring including roller and solar plates complete all as specified and directed.

S&F in repair MS drapery rods of 25 mm dia of PVC coated as in curtain rods complete all as specified and directed

S&F MS PVC sheeted/power coated bracket size 150 mm made to shape suitable for holding curtain/drapery of rod of 25mm dia fixed with PVC rawl plugs and MS steel screws complete all as directed by Engr-in-Charge .

Taking up or down steel tubing and connection including cleaning for refixing or removed to store,15 mm dia bore complete all as specified and directed.

All as per item No 70.00 but 20 mm bore complete all as specified and directed

Cutting chases, pinning in making good to facing on brick walls where required and pointing in CM (1:3) to ends for concealed water tubing and making good, cutting n. exc 10cm girth complete all as specified and directed .

S&F for 20 mm outer dia medium grade CPVC, SDR 11 & plain/Brass CPVC SDR 11 with all fittings (plain and brass threaded) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per Item No 73.00 above but 25 mm outer dia complete all as specified and directed

Dismantling of cast iron 100 mm dia pipes jointed in cement mortar complete all as specified and directed

Dismantling of cast iron 75mm dia pipes jointed in cement mortar complete all as specified and directed

S&F PVC SWR pipes 150 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps for rain water pipes complete all as specified and directed Make : Supreme/ Finolex.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps complete all as specified and directed Make : Supreme/ Finolex.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR bends of 150 mm bore complete all as specified and directed.

S&F PVC SWR bends of 110 mm bore complete all as specified and directed.

S&F PVC SWR bends of 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as specified and directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Supply and fix in repair for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and directed

M&L for old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM (1:6) all complete all as specified and directed

M&L for brick work with half bricks thick fly ash bricks straight or curved on plan exc 6 m mean radius build in CM (1:6) complete all as specified and directed

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of wood and wood based primer of any description not otherwise described over 10cm width or girth complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall to prepare the surface even and smooth by applying two coat of oil bound distemper over one coat of alkali resistant primer incl wall putty (minimum thickness 1.50 mm thick) for complete smooth surfaces all as specified and as directed by Engr-in-charge.

M&L for preparation of newly plastered ceiling surfaces and preparing the surface even and smooth by applying two coat of oil bound distemper over one coat of alkali resistant primer incl wall putty (minimum thickness 1.50 mm thick) for complete smooth surfaces all as specified and as directed by Engr-in-charge.

M&L for complete removal of existing surface and applying two coat of oil bound distemper over one coat of alkali resistant primer for smooth surfaces complete all as specified and as directed by Engr-in-charge.

M&L for preparation of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for complete removal of existing surface preparation of old plastered surface of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar).

M&L for preparation of old plastered surfaces of walls and applying plaster of paris putty of 1 mm thick over plastered surface to prepare the surface even and smooth and applying two coat of oil bound distemper over one coat of alkali resistant primer complete all as specified and as directed by Engr-in-charge.

Demolition of concrete (in roof) of any description and in any position not otherwise specially provided and removing rubbish off the premises complete all as specified and directed

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof, finished fair complete all as specified and directed

M&L for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:3 finished even and fair complete all as specified and directed

M&L for preparation ne surfaces of roof and applying two coats of Polyurethene (PU) acrylic based water proofing liquid compound (minimum 1.5 Ltr PU or manufacture instruction which are higher to be followed) over & including one coat of self priming primer @ one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage/seepage from roof/wall complete all as specified and directed by the Engr-in-Charge. Notes: (i) As per description of theis item minimum two coats of Polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by as per manufacturer instruction. Please note no price adjustment shall be made, if as per manufacturer instructions more coats of Polyurethene(PU) acrylic based water proofing liquid compound & primer are required for roof treatment (ii) Quoted rate shall be deemed to be included for work in building/Structure of any height. (iii) Roof treatment to be carried out by authorised applicator.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

S&F Roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed.

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) in surface channels and drains and Manholes complete all as specified and directed.

M&L for Extra for forming 40 cm inner girth fair finished drains or channels i.e. exc 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating @150 GSM GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

E/M PORTION Taking down carefully aluminium conductor point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc to match with the existing complete all as specified and directed.

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes/suitable for modular, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectional area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

All as per item No 107.00 above but 5 Amp socket on independent board with wire 2.5 Sqmm other switches complete all as specified and directed

All as per item No 107.00 above but 5 Amp socket on same board with other switches complete all as specified and directed

All as per Item No 107.00 mentioned here-in- before but for one bell point controlled by bell push one way switches complete all as specified and directed.

All as per Item No 107.00 mentioned here-in- before but for one two way point controlled by two way switches complete all as specified and directed..

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes/suitable for modular , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for switch piano flush type, single pole, 5/6 Amps, one way complete all as specified and directed.

M&L for Bell push, flush type, 5/6 amp complete all as specified and directed.

M&L for switch piano flush type, single pole, 5/6 Amps, two way switch complete all as specified and directed.

M&L for switch piano flush type, single pole, 16 Amps, one way complete all as specified and directed.

S&F socket outlets 2 in 1, 5/6 Amps, 230/240 V complete all as specified and as directed (For Same Board only)

S&F socket 2 in 1 multipurpose 3 pin, (16 Amps) flush type controlled by one switch ccomplete all as specified and directed.

S&F switch socket combination 5 in 1, 6 pin, (16 Amps) flush type controlled by one switch complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified and directed.

S&F lamp holder, PVC/polycarbonate type with back plate straight or angular Including LED inverter type lamp 12 watt 4 hour backup suitable for batten fittings complete all as specified and directed.

S&F Ding dong, AC 230 Volts, single pole 230 volts complete all as specified and directed.

S&F New gernation energy saving LED bulk head Corvi plus made up of Poly carbonate housing with diffuser in repair round type 10 watt surface mountedround LED Bulk head complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed. Make : Bajaj/Havells/CG/Jaquar.

S&F in repair round type 6 watt surface mounted round LED down light complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed. Make : Bajaj/Havells/CG/Jaquar.

S&F 01x 18 W LED batten light fittings, with T-8 tube rod, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete all as specified and directed. Make : Bajaj/Havells/CG/Jaquar.

Supply and fixing wall security light fittings 35 watts 230v, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65/66 including necessary connection complete with all accessories including connected with 3 core copper cable of suitable 1.5 sqmm size complete all as directed. Make : Bajaj/Crompton/Phillips/Havells/Jaquar

S&F 10W LED light fitting wall mounted batten 2ft, extruded polycarbonate, environmental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt, 6000K including necessary connection complete all as specified and directed. Make : Bajaj/Crompton/Phillips/Havells/Jaquar

S&F wall decorative light fitting with1 light Conical opal globe glass fixture with Lamp E-14 4 Wx1 nickel finishing wall lamp connecting electric connection all as directed by Engr-in-Charge. Make: JAQUAR/BAJAJ/CG/Havells (Cat No -JNL-BRG-WLCONESIE14)

S&F exhaust ventilation fan with louvers of sweep 300mm, 230 volts, with blade and frame and loures steel body, ISI marked complete all as directed by Engr-in-Charge. Make: Usha/Havells/Bajaj

S&F two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked), concealed, including 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: (i) Three runs cable and PVC conduit will be measured as a single unit. (ii) Quoted rate shall be included for necessary chasing, cutting and making good as per existing specification)

S&F two single core, 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: (i) Three runs cable and PVC conduit will be measured as a single unit. (ii) Quoted rate shall be included for necessary chasing, cutting and making good as per existing specification)

S&F GI light grade 40mm dia of size for road cross/cutting on wall, floor, drain etc complete all as specified and directed

S&F XLPE insulated armoured cable, 25 sqmm 4 core,1100 volts grade heavy duty cable, ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as specified and directed.

Excavation in trenches n.exc1.5m wide and not exc 1.5m depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers n.exc 25cm in soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness i.e 18cm thick shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. Make : ABB/Legrend/Scheneider/Hager

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Vertical Triple pole and neutral 415 V, 4 ways with 125 Amp MCCB mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as directed. Make : ABB/Legrend/Scheneider/Hager

S&F MCCBs TPN 125 Amps,16kA, 4 pole 415 Volts,ISI marked and to be housed in DBs complete including necessary connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating). Make : ABB/Legrend/Scheneider/Hager

S&F in repairs MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessary connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating). Make : ABB/Legrend/Scheneider/Hager

S&F in repairs MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. Make: ABB,L&T,legrand (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating). Make : ABB/Legrend/Scheneider/Hager

Supply and fix water heater storage type electric of capacity 25 ltrs BEE 5 star rated including Pvc connection pipe ,drill in wall and fixing properly with sitable fastner nut bolt etc complete testing and commissioning by EIC all as specified and directed. Make : Usha/Havells/Bajaj/CG

Supply and laying of pipe GI medium grade 15 mm dia complete in wall ceiling or floor etc complete all as specified and directed.

Supply and laying of pipe GI medium grade 20 mm dia complete in wall ceiling or floor etc complete all as specified and directed.

S&F Stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15mm bore pipe complete all as specified and directed.

S&F Bib tap cast copper alloy high pressure with crutch or butterfly handle screwed for iron pipe complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts and bolt 450mm long with connecting items all as directed by Engr-in-Charge

Taking down and refixing energy meter up to 25 Amp with connecting electric connection complete all as specified and directed

Taking down fan, sealing cable end dismantling blades and removing fan and blade to store after complete of work painting celling fan complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc. Fixing/Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Disconnecting existing of capacity exc 500 Ltrs but not exc 1000 Ltrs tanks setting aside (or lowering if required ) for repair cleaning end and hoisting if required reconnecting and refixing in position (cleaning repairing etc measured separately) complete all as specified and directed.

S&F 500 Ltr capacity Rotational /moulded Polyehtylene water tank (Cylindrical vertical with closed top minimum three layer) hoisted including dismantling & fixed in position all as specified directed Make : Vectus/Sintex/Prayag

All as per item No 155.00 above but capacity 1000 Ltrs complete all as specified and directed.

S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythene ball screwed for iron pipe 25 mm bore dia with fly nut complete all as directed by Engr-in-Charge.

S&F 25 mm bore GI tubing medium grade in trenches/ Floor/ pillar connection in old or new position including fittings all as specified & as directed including taking down old unserviceable pipe (Make: Bansal/Jindal)

All as per item No 158.00 above but 40 mm bore complete all as specified and directed.

S&F 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

S&F 40 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

S&F garden light fittings 12 watts, LED, dia cast housing with high corrosion resistance surface finish with B 22 holder and pin type LED bulb complete all as specified directed. Make : Magik Lighting Cat No OGFB00001042

M&L for cable in trenches or passing through pipe, XLPE insulated, heavy duty, galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 10 sqmm 4 core complete all as specified and as directed.

M&L for cement concrete 1:3:6, Type C-2 (using 40 mm graded stone aggregates) in foundations for pole etc complete all as specified and directed .

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in coping for pole including form work and finishing the surfaces even and smooth tec complete all as specified and directed.

S&F Cable Junction Box 200X160X98mm in size, made out of thermoplastic sheet having IP 65 protection for outdoor installation fixed with 4 way bakelite cable terminals including 03 Nos polymide gland with check nut (M-32 - 2 nos) fixed on poles with flat iron clamps of size 25x3mm, nuts, bolts, washers etc. including applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer including taking out of old unserviceable cable junction box complete all as specified and as directed. Make : Cat No. K-9250 of HENSEL or equivalent model in SPELSBERG/RITTAL/CAPE

BISWAS ENTERPRISE

M/S GLOBE ENTERPRISE

ANSH CONSTRUCTION

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP