GE 861 EWS-19 (T)/2025-26

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of brick or stone masonry built in cement mortar including all necessary arches quoins etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced in ground floors & pavings n.exc 15 cm thick (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing tiles from site and credit obtained for the same complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames not exc. 1.5 Sqm but with shutters (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description n. exe 1.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutter (any description) area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class ‘B’ brick straight or curved on plan exceeding 6m mean radius in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

All as per item No 10 above but except bricks complete all as specified and directed by Engineer-in-Charge.

M&L for flush pointing to random rubble masonry in cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar (1:6), surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5 mm thick in cement mortar 1:3 finishing on brick or concrete, surfaces finished even & smooth without using extra cement in ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for RCC (1:2:4) Nominal mix type B1 (using 20 mm graded crushed stone aggregate ) as in beams, cantilevers bressumers lintels over 1.5 span beam supported on walls etc complete all as specified and directed by Engineer-in-Charge.

M&L for form work to soffits of suspended slabs such as roof slabs, floors, slabs, landing and similar works etc. fair fished surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer-in-Charge.

M&L precast cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregate for cover slab for Man holes/Septic tank, set in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded crushed stone aggregate as in floor to receive floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

S&F vitrified ceramic dark shade coloured tiles 10mm thick (square/rectangular) polished, area of each tiles n. exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for vitrified tiles dark colour Granite /Marble /wood textures ceramic 10mm tiles in vertical surfaces n.exe 0.36 Sqm, over and including 10mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured joint free tiles 400mm x 400mm 7 to 8mm thick (square/ rectangular), in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:4) for laying floor finish complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured joint free tiles in vertical surfaces 350 x250x7mm/ 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar etc. complete all as specified and directed by Engineer-in-Charge.

M&L for kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

All as per item No 26 above here-in-before but on vertical surfaces of walls /skirting/dado etc., laid over and including 15mm thick cement plaster in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick PCC (1:4:8) type B2 (using 40 mm graded crushed stone aggregate ) as in sub base for receiving floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles 20cm x20cmx25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood 35 mm thick paneled shutter (any number of panels ) with panels of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed by Engineer-in-Charge.

Supply and fixed 35mm thick 2nd class hard wood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (internal sash bars) edges of framing plane, chamfered or rounded fitted and mitred beads for securing glass etc size of members as specified in SSR Part-I Section 8 clause 8.24(a) (kail) complete all as specified and directed by Engineer-in-Charge.

S&F for 30mm thick 2nd class hard wood glazed and skeleton windows/ventilators shutters open rebated and prepared to receive glass, gauge etc , divide into square with plain chamfered or rounded, mitered and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelaminated PVC sheet reinforced with mild steel square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail panelling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 200 mm, complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium anodised barrel tower bolts extruded section of size 200 mm, complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long , complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium anodised barrel tower bolts extruded section of size 150 mm long , complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricated type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium handle extruded fabricate type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricated type anodised of size 100 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs aluminium handle extruded fabricate type anodised of size 100 mm complete all as specified and directed by Engineer-in-Charge.

S&F for butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F in repairs butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F in repair butt hinges 75 mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F for butt hinges 75 mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F MS helical door spring including roller & roller plate complete all as specified and directed by Engineer-in-Charge.

S&F in repair MS helical door spring including roller & roller plate complete 300 mm size complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

S&F in repair 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glasses thickness size quality from wooden or steel frames glazed with old putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

M&L 4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed by Engineer-in-Charge.

Dismantling water storage tanks of 500 litres capacity and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F for Rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squatt pattern closet including lime concrete bedding and all joint making good to the floor complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china bowl urinal flat back, size of (465 x 355 x 265) mm white (min), with grating and union for discharge pipe including flush pipe & waste pipe) complete all as specified and directed by Engineer-in-Charge.

S&F grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC valve less 10 litre capacity symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous china wash hand basin, white, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed. (Including S&F of 15mm bore CP pillar tap, 32mm waste coupling and PVC waste pipe) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm size PVC connection with PTMT nuts of 600 mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm size PVC connection with PTMT nuts of 450 mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms ) complete all as specified and directed by Engineer-in-Charge.

S&F 100 cast iron sanitary connection for WC complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for cast iron 75 mm bore soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floor etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for cast iron 100 mm bore soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floor etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75 mm dia CI floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1complete all as specified and directed by Engineer-in-Charge.

S&F in repair cast iron Nahani trap 75 mm dia including jointing to pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs cast iron 75 mm bore bends (any radius) diminishing pieces or tapers etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs cast iron 100 mm bore cowls complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 15 mm bore CP stop/angle valve cast copper alloy screwed down , high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 15 mm bore CP stop/angle valve with long shank and cup (concealed type) cast copper alloy screwed down , high pressure fancy type complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20 mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore GI tubing med grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm bore GI tubing med grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in-Charge.

Fixing only GI tubing in any grade to walls or floors 15 mm complete all as specified and directed by Engineer-in-Charge.

Fixing only GI tubing in any grade to walls or floors 20 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs aluminium anodised tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S&F in repaired vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repair15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge.

S&F in repair health faucet CP Brass hand Jet Shower 15mm bore dia and 1500mm long CP pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Pillar tap 15mm chromium plated fancy type cast copper alloy with crutch or butter fly handle, screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs bib tap 15mm PTMT any colour high pressure screwed down for iron pipe and fixed ( Minimum weight 90gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs including cover fillets etc. complete all as specified and directed by Engineer-in-Charge.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4 mm thick all as specified.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminium GI/MS as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F hollow PVC wall panelling decorative type consisting of 8 mm thick plain colour PVC pre-laminated sheet inclusive of solvent cement and fixing at site on PVC frame/wooden frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F for 5 mm thick PVC sheet fillets of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame complete all as specified and directed by Engineer-in-Charge.

S&F for 9 mm thick veneered decorative plywood , grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame on wall and ceiling etc complete all as specified and directed by Engineer-in-Charge.

M&L in repairs for weather boarding Clean swan in 2nd class hardwood clean swan , plain , 20 mm thick or feather edges , 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

S&F in repairs timber frame in second class hard wood as in scantling etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc. complete all as specified and directed by Engineer-in-Charge.

S&F for galvalume aluminium zinc coating GI based pre-painted corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roof etc. with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge.

S&F 0.63mm thick plain galvanised mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge.

M &L for preparing plastered or un plastered NEW surface of walls and applying two coats of Cement base paint and priming with alkali resistant priming paint on walls.(Externally) complete all as specified and directed by Engineer-in-Charge.

M&L for applying 3 mm thick wall care putty and two coats of oil bound distemper on NEWLY plastered surfaces of wall including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M &L for preparing plastered or un plastered new surface of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M &L for preparing plastered or un plastered OLD SURFACES of walls and applying two coats of Cement base paint on walls.(External) including complete removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

M&L for applying 3 mm thick wall care putty on OLD SURFACES of wall and including two coats of oil bound distemper on plastered/ unplastered surfaces of wall including complete removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

M &L for applying two coats of white wash on OLD SURFACES of ceiling including complete removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on NEW WOODEN surfaces over a coat of pink primer to new surfaces including preparation of surfaces, over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on NEW STEEL surfaces over a coat of red-oxide primer including preparation of surfaces, over 10cm width or girth including roof CGI painting complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on OLD WOODEN SURFACES including preparation of surfaces over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of OLD STEEL SURFACES over 10 cm width or girth and applying two coats of synthetic enamel paint including roof painting complete all as specified and directed by Engineer-in-Charge.

S&F glass dividing strips, 38x3mm thick, inserted in position, conform to design as in floors complete all as specified and directed by Engineer-in-Charge.

M&L for 100 mm thick PCC (1:2:4) type B2 (using 40 mm graded aggregate ) as in floor over sub base , finished surface even and smooth without using extra cement , laid in alternate bays and joint filled with mastic filling including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for providing 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed by Engineer-in-Charge.

S & F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for Harrison rails/drapery rod 25 mm dia mild steel , chromium plated decorative type with 02 Nos wood finished side brackets for each curtain rod complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 06 but not exc 13 sqcm complete all as specified and directed by Engineer-in-Charge.

S&F 40mm thick , 2nd class hardwood planks , planed one side with butt joints and fixed with nails fixed in any situation complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Wall Lining consisting of Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engineer-in-Charge.

Taking down carefully old U/S point wiring copper/Aluminium (light/ fan /sockets/power) complete and making good to disturbed surfaces as directed by Engineer-in-Charge

S&F in repair of double door type SPN DB 12 Way, 240V with 100A copper busbar each phase , with metallic double door type IP-43 IK 09 protection suitable for housing MCB's all as specified and directed by EIC. Note : MCB DBs shall be concealed in wall wherever directed including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

S&F in repair of double door type SPN DB 08 Way ,240V with 100A copper busbar each phase , with metalic double door type IP-43 IK 09 protection suitable for housing MCB's all as specified and directed by EIC. Note : MCB DBs shall be concealed in wall wherever directed including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

S&F in repair of double door type vertical type TPN DB 4 Way, 415V with 200A busbar , with metalic double door type IP 43 IK 09 protection suitable for housing MCCB's all as specified and directed by EIC.Note : DBs shall be concealed in wall wherever directed including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

S&F MCCB FP 63 Amps,16KA, complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 6 to 32 Amps,10KA, 'B' series 240V complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 40 to 63 Amps,10KA 'C' series 240V complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 32 Amps,10KA 'C' series 240V complete all as specified and directed by Engineer-in-Charge.

M&L for sub-main wiring with 2 runs of 10.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal dis) with all accessories like tees, elbows, junction boxes, reducer etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains including taking up/down old unserviceable sub main wiring and making good the disturbed surfaces/location complete all as specified and directed by Engineer-in-Charge. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green.

Supplying and fixing in repair of 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat of size 16 sqmm for service connection complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repair of 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat of size 10.0 sqmm for service connection complete all as specified and directed by Engineer-in-Charge.

M&L point wiring complete with 1.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC non metallic casing and capping with Accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI make terminal boxes fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 1.5 Sq. mm as earth continuity conductor connected to common earth dolly including suitable size of pvc moulded box/hylam sheet fixed on wall for fixing the switches, switch, socket complete all as specified and directed by Engineer-in-Charge. (a) One light point controlled by one 5A switch NOTE: a) Colour coding shall be followed as given below:- i) Phase - Red/Yellow/Blue, ii) Neutral - Black, iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

(b) Description ditto as per item no 141 here-in-before but for One Fan point controlled by one 5A switch complete all as specified and directed by Engineer-in-Charge.

(c) Description ditto as per item no 141 here-in-before but for One 5A flush type switch socket point on same board complete all as specified and directed by Engineer-in-Charge.

(d) Description ditto as per item no 141 here-in-before but for One 5A flush type switch socket point on independent board complete all as specified and directed by Engineer-in-Charge.

(e) Description ditto as per item no 141 here-in-before but for One Bell point control by one 5A bell push switch complete all as specified and directed by Engineer-in-Charge.

M&L for concealed point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5 sqmm size, 1100 volts, drawn through and including non metallic rigid PVC conduit not less than 25mm with all accessories fixed on wall//ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size as earth continuity conductor connected to common earth dolly including required numbers and size of metal Shankin box/ hylam sheet fixed on wall for fixing the switches, switch sockets, sockets, regulators etc complete including making good disturbed surfaces with CM (1:3) to match with the existing surface and existing colour, complete all as specified and directed by Engineer-in-Charge. (a) One light point controlled by one 5A switch. NOTE: a) Colour coding shall be followed as given below:- i) Phase - Red/Yellow/Blue, ii) Neutral - Black, iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

(b) Description ditto as per item no 146 here-in-before One Fan point controlled by one 5A switch complete all as specified and directed by Engineer-in-Charge.

(c) Description ditto as per item no 146 here-in-before One 5A flush type switch socket point on same board complete all as specified and directed by Engineer-in-Charge.

(d) Description ditto as per item no 146 here-in-before One 5A flush type switch socket point on independent board complete all as specified and directed by Engineer-in-Charge.

(e) Description ditto as per item no 146 here-in-before One Bell point control by one 5A bell push switch complete all as specified and directed by Engineer-in-Charge.

M&L point wiring complete with 2.5Sqmm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC non metallic casing and capping with Accessories fixed on wall/ceiling/truss etc with PVC moulded box/ hylam sheet ISI marked fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 2.5Sqmm as earth continuity conductor connected to common earth dolly for 15 Amp switch socket on independent board complete all as specified and directed by Engineer-in-Charge. Note: (a) Colour coding shall be followed as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.

M&L for concealed point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metallic rigid, double lock, ISI marked, not less than 25mm conduit with all accessories such as tee, bends, elbow, reducers, junction box etc. fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuity conductor connected to common earth dolly with and including shankin box/ hylam sheet in any module complete for One 5 pin, 15A switch socket combination on the independent board complete and making good disturbed surfaces with CM (1:3) to match with the existing surface & colour, complete all as specified and directed by Engineer-in-Charge. Note: (a) Colour coding shall be followed as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.

S & F in repair of Ceiling rose, PVC/polycarbonate insulated body type, 3 terminal, 240 volts, 5 Amps complete all as specified and directed by Engineer-in-Charge.

S & F in repair of switch piano flush type single pole one way ,5/6 Amps complete all as specified and directed by Engineer-in-Charge.

S & F in repair of Bell push, 5/6 Amps, 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fix of switch sockets combination box type 3 pin 5 Amps flush type 230 Volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix of switch socket combination box type multi purpose 3 pin 15 Amps controlled by one switch flush type 230 Volts AC complete all as specified and directed by Engineer-in-Charge.

S & F in repair fan regulator electronic flush socket size and making all necessary connections complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Plug top 5/6A complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Plug top 15/16 A all as specified and directed by Engineer - in - Charge

S&F in replacement White cover plate/Existing make with frame 3 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement White cover plate/Existing make with frame 4 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement White cover plate /Existing make with frame 6 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement White cover plate /Existing make with frame 8 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement modular Socket, Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Modular switch 1 way 10A,1 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Modular switch 1 way 16A,1 module complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Modular Fan step regulator, 120W - 2 module complete all as specified and directed by Engineer-in-Charge.

S & F in repair bell, DING DONG, 230 volts, SP complete all as specified and directed by Engineer-in-Charge.

S & F in repair of lamp holder PVC/polycarbonate insulated body type complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair of PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair of PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair of 9 watt pin type LED bulb complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair wall/surface mounted 20W LED batten fitting engineering plastic battern with white acrylic cover complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair wall/surface mounted 10W LED batten fitting engineering plastic batten with white acrylic cover complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core copper conductor cable with suitable size and complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair new generation recessed mounting downlight ultra slim SQUARE/ROUND Luminaire 15 watt and high translucent diffuser provides high quality economic energy saving lighting complete all as specified and directed by Engineer-in-Charge. (Suitable for modular/POP/Gypsum ceiling)

Supply and fixing in repair new generation recessed mounting downlight ultra slim SQUARE/ROUND Luminaire 12 watt and high translucent diffuser provides high quality economic energy saving lighting complete all as specified and directed by Engineer-in-Charge. (Suitable for modular/POP/Gypsum ceiling)

Supply and fixing in repair new generation recessed mounted ultra slim panel LED 2'X2' Luminaire 36 watt and CRCA powder coated body and high translucent diffuser provides high quality economic energy saving lighting to modern offices complete all as specified and directed by Engineer-in-Charge. (Suitable for 600 x 600 mm grid modular/POP/Gypsum ceiling)

S&F in replacement including taking down old unserviceable 1100 volt grade copper conductor cable single core 1.5 sq mm complete all as specified and directed by Engineer-in-Charge.

S&F in replacement including taking down old unserviceable 1100 volt grade copper conductor cable single core 2.5 sq mm complete all as specified and directed by Engineer-in-Charge.

Disconnecting & taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size & greasing ball bearing with specified quality grease & re-commissioning the same including making new electric flexible wire connection complete all as specified and directed by Engineer-in-Charge. Note: Replacement of spare parts, rewinding, painting etc to be measured and paid separately under relevant items of Sch 'A'

M&L for replacement of short circuit/over heated winding of stator of ceiling fan of any make having 1200mm sweep with matching gauge & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling complete re-assembling of fan with testing etc complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of short circuit/over heated winding of stator of Exhaust fan of any make having 300/450mm sweep with matching gauge & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling complete re-assembling of fan with testing etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of gun metal bush with suitable size for ceiling any make any size and sweep complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of ball bearing suitable for 1200/1400 mm sweep ceiling fan of any make complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of canopy (top & bottom) of ceiling fans any make/size with canopy of matching colour complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of rubber reel with nut, bolts, split pins etc of ceiling fan with rubber reel heavy duty for hanging fan complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of connector block of ceiling fan suitable size of approved quality complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of capacitor of ceiling fans with capacitor having capacity 2.5mfd complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of blade of ceiling fan of any make with aluminium blade duly painted of sweep 1200mm including provision of screws etc fixing purpose complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of hanger clamp assembly of down rod for hanging of ceiling fan with nuts, bolts, washers & split pin complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of capacitor of Exhaust fans having capacity 3.15mfd complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of Exhaust fan blade, heavy duty 450/600mm sweep, complete all as specified and directed by Engineer-in-Charge.

Taking down carefully geyser 25/35/50 litres capacity from wall after unscrewing nuts/bolts etc. and again refixing in position after repair and replacement of spare parts including testing complete all as specified and directed by Engineer-in-Charge. Note:-spare parts shall be measured and paid for separately under respective items.

S&F in replacement of heating element AC 230 Volt of rating 1500W ISI mark as per existing any type complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of heating element AC 230 Volt of rating 2000W ISI mark as per existing any type complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of thermostat switch AC 230 Volt adjustable range from 0-90 degree Celsius complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of flexible PVC connection pipe heavy duty suitable for hot water to bear the temp of 100 degree centigrade with outlet and inlet connection brass adopters , washers of size 450 mm long 15 mm dia bore complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of Indicator lamp round/square type suitable for geyser 25-50 litres all as per sample AC 230 Volts, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of auto cut switch suitable for geyser 25-50 litres 230 volts AC all as per sample, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of geyser assembly suitable for existing geyser 25-50 litres 230 volts AC all as per sample, complete all as specified and directed.

S&F in replacement of geyser bolt & nut suitable for existing geyser 25-50 litres 230 volts AC all as per sample, complete all as specified and directed by Engineer-in-Charge.

S&F in repair of double door type SPN DB 04 Way, 240V with 100A copper busbar each phase , with metallic double door type IP-43 IK 09 protection suitable for housing MCB's complete all as specified and directed by Engineer-in-Charge. Make: Legrand /Seimens/ABB/C&S. Note : MCB DBs shall be concealed in wall where ever possible including making good the surface to match with surrounding complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Socket 3 pin 5 Amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. Make :Cone /Anchor/legrand/Crabtree

S&F in repair for Socket outlet 2 in 1, 3 pin, 6 and 16 amp flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. Make :Cone /Anchor/legrand/Crabtree

Material and Labour for Earthing complete with MS plate electrode of size 600 X 600 X 6 mm buried directly and preferably vertically in ground (earth pit not less than 2.50 mtrs deep below ground level ) with top edge of the plate not less than 1.25 Mtrs below ground level, connected to 4mm dia galvanised iron or steel wire etc all as shown in electrical plate No. 3 of SSR Part-I, connected to Earthing test point including earth work, 1:3:6 C1 PCC chamber, 1:2:4 B1 PCC cover with 8 mm dia steel bars at 100 mm C/C suitable size of GI pipe for earth lead protection and watering, water funnel etc. complete all as specified and directed by Engineer-in-Charge.

M/S U.K. ENTERPRISES (BID ID -3360853)