Construction of Gugauli to Palra Via Badraha Baba Link Road under Twarit Aarthik Vikash Yojana (5 year Maintenance)

Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5 meter transporting to sites spreading grading to require slope and compaction to meet requirement of table 300.1 & 300.2 with a lead up to 50 meter as per MORD technical specification cause 301.5 MORD sepecification 301.5(i) S.No. 3.4

Construction of Subgrade with Stablization of Soil with 2% slaked lime Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads. transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead up to 1000 m as per Technical specification cause 303.1. including Stablization with 2% staked lime including its mixing with rotabator complete. Two Layer

Construction of granular Sub Base by providing well graded material, spreading in uniform layers with motar grader on prepared surface mixing by mix in place method with 2% cement (OPC) with rotavator at OMC, and compacting with smooth wheel rollar to achieve the desired density complete as per technical Specification Clause 401

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC and 4% cement (OPC) in mechanical mixer (pug mill)-carriage of mixed material by tipper to site, laying in uniform layer in sub base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achive the desire density including lighting, barricading and maintenance of diversion etc as per Table 400.11 & 400.12 and Technical Specification Clause 405.00

Providing and applying tack coat with V.G.-10 bitumen using bitumen pressure dristributor @ 0.35 to 0.45 kg. per sqm. on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing laying & rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line ,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant ,laying and rolling with a three wheel 80-100 KN static roller capacity finished to required level and grades to be followed by seal coat . Claues 508

Providing and laying seal coat Type-C sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using As per Technical Specification Clause 510

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing, laying, spreading and compacting stone aggregates of 22.4-53mm to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading III as per Technical Specification Clause 405.

Construciton of un-reinforced, plain joint at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base with 43 grade cement or any other type as per Clause 1501.2.3 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm mixed in a concrete mixerof not less than 0.20cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work as per drawing. spreading the concrete with shovels, rakes, compacting using needle, screed and plate vibrators and finished in continous operation including provision of contraction and expansion, construction joints, applying joint filler board near approcehes to bridges/culvert and construction joints, admixture