138WE/L-123/2025-26

M&L for preparation of new or old untreated wood or wood based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F 2nd class soft wood 35 mm thick glazed and gkelton shutter, open and prepared to receive the glass, gauze etc. (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured separately) complete all as specified and as directed by the Engr-in-Charge.

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated, including backing with thermocol sheets or as specified by manufacturers including dismantling existing one all as specified and directed.

M&L 6mm (5 No's ply) thick veneered decorative (Knotty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work, including dismantling complete all as specified and as directed.

All as per Serial item No. 62 above, but on ceiling.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding including dismantling complete all as specified and as directed.

M&L french polishing on wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on new surface with two or more coats complete all as specified and as directed.

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws including dismantling complete all as specified and as directed.

M&L for cleaning of blocked cast iron / PVC pipes of bore 100 to 150 mm dia pouring hot water, rodding from trap to manholes to septic tank with iron rod, jute bags etc and well flushing with water mechanically or manually using with cleaning materials including manholes and removing of waste material to out of defence land complete all as specified and directed. Note :- The cost of cleaning material and and earth work for pits is deemed to be included in the unit rate.

ring hot water, rodding from trap to manholes to septic tank with iron rod, jute bags etc and well flushing with water mechanically or manually using with cleaning materials including manholes and removing of waste material to out of defence land complete all as specified and directed. Note :- The cost of cleaning material and and earth work for pits is deemed to be included in the unit rate of this item.

Supply and filling Mono Ethylene Glycol MEG 99.99 % Pure clear, minus forty degree centigrade freezing Temperature & colourless in sealed containers having Specific gravity 1.1151-1.1156 at 20 Deg C with Dietylene Glycol DEG Contents less than .04% by weight, with minimal or zero Chlorides, Iron, Sulphates & Ash and Acidity less than 10 PPM and water content .0.0104 to 0.04 % with complete miscibility with water, for CHS at MAP and misc. works under AGE E/M-I. Make : Indian Glycol Limited/ Reliance Industries/IOCL Note: (a) Test report from BIS certified Lab and Gas Chromatography shall be submitted by the contractor for each lot of supply. (b) In addition, Contractor shall make arrangements to check the specific gravity of Glycol at site in the presence of Engr-in-Charge for each lot of supply. (c) Necessary documents shall be maintained for the above tests duly signed by Contractor and Engr-in-Charge.

carbon/oil deposits with suitable coil shine chemical including repair to coil assembly by welding if there is any leakage found or any other repair required at site and reassembling/ testing the same, complete all as specified and directed by Engr-in Charge.

M&L for insulation of MS Pipe with PUF slab 40mm thick with and including applying bituminous compound and GI cladding with 26 gauge GI sheet complete of size 50mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Supply only sequence controller suitable for 6 lakh kilo/hr with burner rod assembly, complete all as specified and directed. Make- Siemens

Material and labour for welding work to rectify leakage of glycol of pipe size up to 100mm complete all as specified and directed by Engineer-in-Charge.

S & F in replacement of Turbo charger suitable for 250 KVA DG set CP No 105292000069.

Supply only temp controller digital type DTC 503 with sensor suitable for 6 lakh kilo/Cal/hr LAL 2.25 burner rod assembly, complete all as specified and directed.

All as per Ser item No 100 above, but for MS pipe of size 25 mm.

Material and labour for checking, Inspection, maintenance and servicing of DG set capacity 250 KVA complete including replacement of unserviceable spare parts of the DG set (comprising of Engine/ Alternator/ Control panel) of the following capacity for smooth functioning complete all as per manufacturers instructions and all as directed by Engineer-in-Charge. A.(a) Checking of lubricating oil condition (b) Checking engine for oil, water leakage and correcting the same (c) Checking of all the nut bolts of engine and alternator (d) Checking of all belts and adjust the tension properly (e) Cleaning of air filters (f) Checking and readjusting the valve clearance (g) Change of Oil/ Fuel filters and engine oil if necessary (h) Checking of starter motor battery and charger (i) Checking of cooling system and fuel system (j) checking of all power cables and AVR connections and mounting bolt tightness of alternator (k) checking the function of AVR general checks (l) Checking of control panel meters and gadgets function (m) Checking of all control and safety wirings. B. (a) Checking of flexible coupling of engine and alternator (b) Cleaning of crank case ventilation pipe (c) Checking of injectors and fuel pump (d) Checking of alternator and carbon brushes complete all as specified and directed. Note : (i) Cost of Spares required will be paid and measured separately. (ii) Servicing/routine check up carried out through authorised service centre of manufacturer. (iii) Make of spare recommendation by auth service centre of manuf

acturer.

Replacement of Oil filter element as per existing for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge. Make : Kirloskar/Cummins/Greaves.

M & L for changing/ topping up of best quality of engine oil 20W40 type for various type/ capacity DG sets including removing of old burnt engine oil from DG Sets complete all as specified and/or as directed by Engr-in-Charge.

Replacement of Air cleaner element (inner and outer) suitable for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge. Make : Kirloskar/Cummins/Greaves

Replacement of Fuel filter elements (primary & secondary) for DG Sets complete all as specified and/or as directed by Engr-in-Charge. Make : Kirloskar/Cummins/Greaves

S&F in replacement of battery 12V 180 AH heavy duty and maintenance free complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of automatic voltage regulator of DG set capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of fuel pipe with banjo bolt at both side suitable for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of Dynamo Assy for DG Set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of water pump assembly for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of 'V' belt for water pump suitable for DG Sets of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M&L for replacement of Fan Hub assembly for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement of lub oil pump suitable DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

Supply and Replacement of thermostat valve suitable for DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

M &L for Removing the fuel injection pump (FIP) & injectors from DG sets and carry out servicing and calibration including replacement of injectors nozzles, etc. and refitting the same for smooth and efficient functioning complete all as specified and/or as directed by Engr-in-Charge. Note :-Repairs will be carried out from authorised workshop of MICO or manufacturer of DG set of capacity 250 KVA complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix Offload Changeover Switch- AC 21 (side handle) in sheet enclosure, 415V AC, 50 Hz, of capacity 200 AMP, TPN complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix digital Ammeter (0-800 Amp) capacity.

Supply and fix Digital Voltmeter (0-500 Volt) capacity.

Supply and fix of Air pipe (Turbo to Radiator) for any capacity of DG Set complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix battery cable assy. with copper conductor multistranded RED and BLACK colour 2mtr long 21sqmm for connection to self starter unit to Battery unit complete all as specified and/or as directed by Engr-in-Charge.

Dismantling storage type water heater, vertical type, 25 Ltrs capacity taking out all unserviceable/ defective parts & supply and fix in replacement, inner tank with single weld line design, outer tank, high density PUF insulation, thermostat, assembly, safety valve, NRV, heating element 2.0 Kilowatts operating voltage 220-240 volts, indicating lamp(Red, Green), Plug top, Hot/ Cold water pipes including wiring work, all other accessories required, painting and refixing & testing the same complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement of 'V' belt for water pump suitable for capacity of DG 180KVA Sets complete all as specified and/or as directed by Engr-in-Charge. Make : Kirloskar/Cummins/Greaves

Supply and fix in replacement of fuel pipe with banjo bolt at both side suitable for DG sets complete all as specified and/or as directed by Engr-in-Charge. Make: Kirloskar/Cummins/Greaves

S&F in replacement of self starter assy 24 Volts complete for DG set 250 KVA complete all as specified and/or as directed by Engr-in-Charge. Make : Greaves or equivalent approved make as approved by GE.

S&F in replacement of heating elements 2.0 KW suitable for water storage heater vertical/ horizontal type complete all as specified and/or as directed by Engr-in-Charge.

M&L cleaning of radiator using K oil and radiator cleaning solution hydraulic acid by pressure of pump and brush and necessary welding whichever is required complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix LED down light (round, cool white) of capacity 15 Watt, motion sensing based with 4.5 mtrs radius, 215 Volts complete all as specified and/or as directed by Engr-in-Charge.

Supply & topping up of best quality anti freezing, Inhabitor Corrosion (Coolant ) liquid for DG set at various capacity and locations complete all as specified and/or as directed by Engr-in-Charge. Make : Castrol/Veedol/Volvoline

Supply and fix in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and/or as directed by Engr-in-Charge.

Point wiring complete with 1.5 Sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC Casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead all as specified and directed for the following:-

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as spfd and directed by Engr-in-Charge.

One light/exhaust fan point controlled by one way switch.

Supply and fix modular switch piano flush button single pole 6 Amps 230 volts one way combined 1 module complete all as specified and directed.

Supply and fix modular switch Socket combination outlet multi purpose 5 pin 6 Amps and 16Amps 230 volts combined 2 module complete all as specified and directed.

Supply and fix modular switch piano flush button single pole 16 Amps 230 volts one way combined 1 module complete all as specified and directed.

Supply and fix plastic surface box 3 module with press plate and frame complete all as specified and directed.

Supply and fix plastic surface box 4 module with press plate and frame complete all as specified and directed.

Supply and fix plastic surface box 6 module with press plate and frame complete all as specified and directed.

Supply and fix plastic surface box 8 module with press plate and frame complete all as specified and directed.

Supply and fix plastic surface box 12 module with press plate and frame complete all as specified and directed.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways all as specified and directed by Engr-in-Charge.

Supply and fix MCB SPN 63 Amp 240 Volts AC ISI marked all as specified and directed by Engr-in-Charge.

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as directed.

Supply and fix Ceiling rose, surface Bakelite three terminals complete all as directed.

One switch socket outlet 6 Amps, 230 volts point on same board.

All as serial item No 134 above, but using cables 4 Sqmm size.

M & L for submain wiring along with earth wire with the following sizes of FRLSH insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x 6.0 sq. mm + 1x 6.0 sq. mm earth wire complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fix in replacement exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and/or as directed by Engr-in-Charge.

Supply and fix in replacement of surface mounted square 2x2 LED panel 36 Watt, light with high quality diffuser for uniform light IP 20 protection complete all as specified and/or as directed by Engr-in-Charge.

Taking down old u/s wall recessed light and supply and fix environmental friendly, new generation, energy saving, decorative rectangular shaped wall recessed luminaire with SMD as light source complete all as specified and/or as directed by Engr-in-Charge.