PROVN OF KOTA STONE FLOORING IN STAIRCASE IN MD OFFR ACCN, PROVN OF 2 X B TYPE VEH PARKING SHED WITH FLOORING AND PROVN OF SOLAR STREET LIGHT WITH POLES AT LEKHAPANI

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundations,manholes,laying cables,pipe lines,etc and getting out in soft/ loose soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25 cm of soft loose soil,complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum,getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L PCC (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L PCC (1:2:4) type B.-2, (using 40mm graded stone aggregate) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L Providing PCC(1:2:4) type B1, (using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges and other similar bands including use of formwork complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed.

Taking down shutters of any description area exc 1 sqm but n.exc 2 sqm and refixing in the same opening after adjusting and easing complete all as directed by Eng-in-charge.

S&F Structural steel work in hollow square/rectangular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS:4923-1997 (Reaffirmed 2009) grade Yst.-310 complete all as specified and directed.

S&F Structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS:1161-1979 (2009) grade St.-240 complete all as specified and directed.

S&F Rolled mild steel Plates (plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment conforming to Fe:410-W(Gde-E-250) quality-A complete all as specified and directed.

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated Plain steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in Evas roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing debris beyond the premises,complete all as specified and directed.

M&L Hardcore of broken stone boulder of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to true surface all as specified and directed.

Rolling and consolidating formation surface in cutting using power roller exc 8 to 12 tonne complete all as specified and directed by Eng-in-charge.

M&L PCC ( 1:3:6) type C-2 (using 40 mm graded stone aggregate), as in sub base flooring,filling in foundations and mass concrete,etc complete all as specified and directed.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. brushing neat cement slurry with 3.0 kg of cement per sqm,complete all as specified and directed.

M&L 25 mm thick PCC (1:2:4) type B-1, (using 20mm graded stone aggregate) as in floors and surface finished with even and fair without using extra cement complete all as specified and as directed.

M & L 18-20 mm thick of size 550 mm x 550 mm prepolished granite finished machine cut kota stone slab laid & jointed with grey cement slurry in horizonal surface over & including 20mm thick screed bedding layer of CM (1:4) and pointed with grey, cement as in stairs flooring of including cutting and rounded to chamfered on edges complete all as specified and as directed by Engineer-in-charge.

M & L 18-20 mm thick prepolished granite finished machine cut kota stone slab laid & jointed with grey cement slurry in horizonal surface over & including 20mm thick screed bedding layer of CM (1:4) and pointed with grey, cement as in stair case steps in full length of tread in single piece including cutting and rounded to chamfered on edges complete all as specified and as directed by Engineer-in-charge. Note : Kota stone in tread shall be in single piece of full length.

M & L 18-20 mm thick of size 550 mm x 550 mm prepolished granite finished machine cut kota stone slab laid & jointed with grey cement slurry over & including , cement as in skirting/dado and pillar including cutting, rubbing, polishing over & including 10 mm thick screed bedding layer of CM (1:4) complete all as specified and directed by Engineer-in-charge.

M & L 18-20 mm thick prepolished granite finished machine cut kota stone slab laid & jointed with grey cement slurry over & including , cement as in risers of stairs case steps in full length in single piece, including cutting, rubbing, polishing over & including 10 mm thick screed bedding layer of CM (1:4) complete all as specified and as directed by Engineer-in-charge. Note : Kota stone in Raisers shall be in single piece of full length.

Providing 3mmx5mm groove cut in the edge of the Raiser to the full length complete all as directed by Engineer-in-Charge.

M&L for 18-20mm thick,granite stone slab pre polished jet black in one piece on steps slabs etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab all as specified over 15 mm thick cement screed bed in CM (1:6). complete all as specified and as directed.

M&L Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with grey cement and no pigments, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size /shape, made by table vibratory method using PU mould , laid in required colour & pattern over and including 50mm thick compected bed of course sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layers through vibratory compaction by using palte vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complete all as specified and as directed by Engineer-in-Charge.

M&L Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with grey cement and pigments, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size /shape, made by table vibratory method using PU mould , laid in required colour & pattern over and including 50mm thick compected bed of course sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layers through vibratory compaction by using palte vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complete all as specified and as directed by Engineer-in-Charge.

M&L for kerb stone of using RCC M-30 (Design mix) (using 20mm graded stone aggregate) with size 30cm x 30 cm and not exc 15cm wide, set in CM (1:4) with joints to match including necessary excavation in any type of soil return filling and removal of surplus soil,etc complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or concrete or stone wall surfaces including racking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed by Engineer-in-charge

M&L Rendering 10.mm thick plaster in CM (1:6) on fair faces of brick work or concrete surfaces including finishing top even and smooth without using extra cement complete all as specified & directed.

M&L Rendering 10.mm thick plaster in CM (1:4) on concrete as on ceiling surfaces including finishing top even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces including finishing fair and even complete all as specified and directed.

M&L Prepration of newly plastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L Preparing surfaces to new plastered surfaces of walls and applying three coats of white wash over a coat of 1mm thick wall care putty complete all as specified and directed by Eng-in-charge.

M&L Preparation of surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Eng-in-charge.

M&L Complete removal of the existing surfaces of walls and applying two coats of white wash over a coat of 1mm thick wall care putty complete all as specified and directed by Eng-in-charge.

M&L Preparation of ceiling surfaces and applying two coats of white wash complete all as specified and directed by Eng-in-charge.

M & L Preparation of old wooden surface, of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

M&L Preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paintover a coat of red oxide primer complete all as specified and directed.

M & L Preparation of old steel surface, of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.

S&F All in one solar street light 20 W LED with high efficiency mono crystalline solar panel, new age Lithium Ferro Phosphate Battery with inbuilt BMS technology, back up time 2 days minimum, High Efficacy LED , MPPT Solar charge controller, PIR motion sensor & uniquely designed aluminium housing device including mounting brackets, complete all as specified and as directed by Engr-in-Charge. Note:Tenderer shall opt standalone solar street light system from MNRE suppliers or manufacturers of Make: Crompton/ Philips/Havells.

S&F 40 mm bore GI tubing, (medium grade) for fixing the solar street light including painting and all fixing arrangement as per standard method complete all as specified and as directed by Engr-in-Charge.

M&L for P.C.C. (1:2:4) type B-1 (using 20mm graded stone aggregate) for coping of poles or any other indicated work including form work and 15 mm thick plastering CM (1:4) and making the surface smooth and even by using extra cement complete all as specified and as directed by Engr-in-Charge.

ADNEEDS ENTERPRISE

M/S SINGH TRADERS

SAHASRA CONSTRUCTION

M/S RK Trading

M/S A K ENTERPRISE