Construction of Piggery unit, Poultry unit, Integrated Livestock Farms and Model Livestock Units in Advanced Institute for Integrated Research on Livestock and Animal Sciences at Thalaivasal koot Road in Salem District

Amount

Civil Works

Earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary refilling the sides of foundation with excavated earth in layers of not more than 15cm thick well rammed consolidated and depositing the surplus earth with in the compound in places shown by the departmental officers within an initial lead and lift and clearing, levelling the site etc., complete complying with standard specifications.

open excavation

Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling in foundation and basement with excavated earth in layers of not more than 15cm thick, well rammed, watered and consolidated etc., complete complying with standard specification.

Supplying and filling of gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification.

Brick work in Cement Mortar 1:5 (One cement and Five M.sand) using second class ground moulded chamber burnt bricks of size 9”x 4½”x 3” for the following including curing, etc., complete complying with standard specification For foundation and basement

For superstructure in Ground floor

For superstructure in first floor

Brick partition walls of 11.50cm thickness using best quality II class ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three M. Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) For foundation and basement

For superstructure in Ground floor

Brick Masonry in cement mortar 1:3 (one cement and three M-Sand) using best quality of first class chamber burnt bricks of size 9”x41/2”x 3” for foundation and basement including curing, etc., complete complying with standard specifiction. For foundation and basement

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For square or rectangular colums,boxing top and bottom slab,sill slabs, sunshade facia,fins and drops etc.,

For slabs,rectangular Tee or Eill beams,lintels,staircase waist and landing salbs,landing beams,loft slabs,canopy slabs,beams etc.,

Reinforced Cement Concrete 1:11/2:3 (One Cement, one and half M.sand and three hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcement grill, fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrator, finishing, curing, etc., complete and providing fixtures like fan clamps in the RCC floor/roof slab wherever necessary and bearing surfaces of wall, beam etc. shall be finished smooth with cement mortar 1:3 (One Cement and Three P.Sand) 12mm thick and kraft paper laid over it without claiming extra, etc., complete complying with standard specification as directed by the departmental officers. For foundation and basement

For superstructure in Ground floor

For superstructure in first floor

Supplying, fabricating and placing in position of steel reinforcements using MS / RTS rods for all RCC works as per design given including cost of steel. Binding wire, straightening the rods, welding of rods, dia above 25mm in all floors complying with standard specifications. [The welding should conform to BIS. Wherever required at contractor’s expense.]

Plastering with Cement Mortar 1:5 (One cement and Five P.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with cement mortar 1:3 (One cement Three P.Sand ) 12mm thick with water proofing compound in all floors including finishing neatly curing etc., complete complying with standard specification.

Plastering with cement mortar 1:3 (One cement Three P.Sand ) 20mm thick with water proofing compound in all floors including finishing neatly curing etc., complete complying with standard specification.

Supplying and fixing of M.S. pipe of various sizes (3" dia pipe for vertical posts and 1½" dia M.S. pipe for stay) enbedding with cement concrete 1:2:4 to a depth of 0.50 and leaving 1.50m above the ground including providing necessary for lening applying a coat of primer ect. complete.

Supplying and fixing of powder coated galvanized aluminium metal roofing sheet 0.47mm thick JSW or equivalent of ISI make of different colour sheet for roofing with necessary adjustable ridges seater by using “U” or “J” bolts and nuts with washers or SDST screws and also the labour charges for fixing in position etc., complete as directed by the Engineer,i/c.,

Supplying fabricating, erecting of colour Galvalume 0.47mm ridge sheet including cost of self drilling (SDST) screws with washers, fixing charges lead and lift etc., complete.

Supplying and fixing of double side pre-polished Cudappah slab for Cupboards, racks, platform in all floors including the cost of cement mortar, curing etc., complete complying with standard specification. 38mm to 40mm thick

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Supplying and fixing in position of weld mesh door of size as may be directed using 40 X 40 X 6mm M.S. angle for outer frame using 40 X 40 X 6 mm M.S angle and 40 X 6 mm M.S. flats for stiffeners horizontally 1" X 1" M.S. weld mesh 10 gauge for panels including cost of mateirlas,and labours for wrought and put up, applying a coat of primer etc., complete as directed by the Engineer,i/c.,

Supplying and fixing in position of weld mesh grill of size as may be directed using 40X40X6mm M.S. angle for outer frame, 40X6mm M.S. flats for bracings, 1¼”X 1¼”M.S. weld mesh 10 gauge for panels including cost of materials, labour for wrought and put up and applying a coat of primer etc., complete.

Supplying and fixing in position of 2''x2'' size chain link fencing 10 gauge and fixing with M.S. Angle post using 16 gauge G.I. Wire including running the 2 ply and 4 pin G.I. barbed wire 12 gauge at bottom, middle and top of M.S. angle posts (As stiffner to the chain link fencing) etc, complete copmplying with standard specification.

supplying and fixing of UV treated polypropylene co-polimer plastic slatted flooring made of unbreakable plastic of size 60x60cm each panels, with manure passing whole with break load 250 kgs and gap of leg stall should not exceed 15mm and depth of the panel should be 50mm with interlocking arrangements.(colur and make should be get approved by engineer incharge).

Supplying and fixing in position steel balustrades using 20mm square rods at 150mm centre to centre and one baluster in each step centrally located and the top shall be connected with the handrails by means of M.S. Flats of size 40mm x 6mm connecting all square rods to the entire length and fixed with handrails 40mm MS ‘B’ class pipe and bottom fixed in the step concrete including cost of square rods and flat MS pipe and applying one coat of red oxide primer to ht iron surfaces, etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing 50mm dia (2mm min tickness), MS tube hand rails with balustrade and horizontal rails as per design and drawings including floor flange ,anchor plate, grouting, welding and grinding etc., Running length of mild steel hand rail will only be measured for payment)

Flooring with the Eurocon tiles of size 20mm thick laid over cement mortar 1:3 (One cement and three M.Sand) 20mm thick and pointing the joints to full depth of slabs with cement mortar 1:3 (one cement and three M.Sand ) mixed with colour oxide including laying, finishing, polishing with machine polish, curing etc., complete complying with standard specification

Paving the floor with Designed Colour double charged Vitrified tiles of size 60 x 60 x 8mm in all floors over a base layer of Cement Mortar 1:3 (One cement and three M.sand) 20mm thick and pointed with white cement mixed with colouring pigments at the rate of 0.3 Kg/sq.m including finishing neatly and curing, etc. complete, complying with standard specification and as directed by the departmental officers. (The basic cost of tiles should not be less than Rs.80/-- Sq.ft)

Paving the floor with Designed Colour Stain free Nano polish Vitrified tiles of size 60cm x 60cm x 8mm in all floors over a base layer of Cement Mortar 1:3 (One cement and three M.sand) 20mm thick and pointed with white cement mixed with colouring pigments at the rate of 0.3 Kg/sq.m including finishing neatly and curing, etc. complete, complying with standard specification and as directed by the departmental officers.

Supplying and fixing with anti skid ceramic tiles of size 12''x18''of approved quality and make and colour with cement mortar 1:3 [One cement and three sand] 20mm thick base plastering pointing the tiles with coloured cement to match the colour of the tiles, finishing neatly, cleaning the surface neatly etc., complete and as directed.

Paving the floor with Self Designed Colour ceramic tiles of size 305x305x6mm in all floors over a base layer of cement mortar 1:3 (One cement and three of M.sand) 20 mm thick and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg / Sqm including etc., complete complying with standard specifications. The tiles should be got approved by the departmental officers before executing of works )

Dadooing walls with best approved quality, printed design colour glazed tiles of size 300 mm x 450 mm x 6 mm sizes set in Cement Mortar 1:2 (One Cement and Two M.sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers

Providing and fixing doors with door frames as per the design and details with the door frame made of well seasoned good quality teak wood frame size of 125mmX100mm finished with melamine polish of approved make, colour & pattern as per drawing and the door made of 35mm thick flush door shutters of solid core block board type bonded with phenol formaldehyde synthetic resin thermo pressed with 8mm thick teak wood external edge lipping finished with melamine polish of approved make, colour & pattern as per drawing. The construction procedure of the shutter should be as per IS:2202.The size of block, shall perfectly correspond to the maximum size of lock, covered in IS:2209.All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. The rate shall inclusive of supplying and fixing 6 nos of MS holdfasts of size 230x50x6mm MS flats suitably folded to the rejoined ‘Z’ shape to have two end flats 50mm long and over all length of the horizontal position as 230mm and including making necessary groove in the two end flats to accommodate screws, and the following of hinges and other hardwares; complete as directed by the Engineer in charge. for Double Leafs doors:- 1) SS 304 ball bearing butt Hinges of size 125x63x3mm - 6 Nos. 2) D type Handle 300 x 25mm in SS 304 - 2 nos 3) SS 304 Tower bolt 12mm dia 300x38x2.4mm – 2nos 4) Mortise dead lock with Europro file Cylinder 60mm Length (one side key other side thumb turn) with 4 level Master Key - 1 no for Single Leafs doors:- 1) SS 304 ball bearing butt Hinges of size 125x63x3mm - 3 Nos. 2) D type Handle 300 x 19mm in SS 304 - 1 nos 3) SS 304 Tower bolt 12mm dia 300 x 38 x 2.4mm – 2nos 4) Mortise lock with D type Handle Profile with 4 level Master Key - 1 no 5) cam action door closer - 1 nos specification same as above but the finishing of door shutters on both sides with 3.5mm thick veneer of approved color and finishing with melamine polish. The basic cost of veneer. The rate should be quoted for single side area of the door shutter - Single leaf

specification same as above but the finishing of door shutters on both sides with 3.5mm thick veneer of approved color and finishing with melamine polish. The basic cost of veneer. The rate should be quoted for single side area of the door shutter - Double leaf

Solid PVC door shutters using 19 gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture fittings. the overal size of styles shall be 50mm x 30mm. The overall size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The overall size of frames shall be 50m x 45mm with suitable rebate for housing the shutter. a) Solid panel PVC door with frame

Providing and fixing in position first quality teak wood beading / architrave of finished size as given below, made to shape and pattern approved with necessary pins, nails, screws, bolts using teakwood conforming to specification. Rate shall include two coats of Duco Paint over a coat of wood primer etc. as directed.

Supplying, fabricating and fixing in position standard pristine white U-PVC (Un-Plasticized Polyvinyl Chloride) partly fixed and partly sliding windows a sper the design andd drawings and making necessary opening for the exhaust fan fixning in all floors with extruded upvc sections of required sizes as per IS Standard with necessary accessories such as rubber beedings with best quality rubber, lock, handle, supplying and fixing 4mm thick plain / frosted glass including the cost of all materials, labour, power consumption required for the fabrication, drilling holes in RCC columns, floor, masonry wall wherever necessary with power drills to the required extent and making good to the original condition after fixing etc., and as directed by the Engineer-in-charge.

UPVC VentilatorSpecification:Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outerframe 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) doors the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI / 1mm 125 GSM and 100% corrosion free, the profiles are multi-chambered sections with all thick of 2mm. The FPDM rubber covered with over all the edges of frame and shutter the shutter will be provided with ESPAG multi power point locks and also handle to be provided. The corners and joints should be welded and cleaned. Strong locking systems and as per size for arresting noise and energy loss. The door should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The door should be got approved from the Executive Engineers before use on work.

Weathering course concrete using best quality broken brick jelly of size of 20mm uniform gauge in pure slaked lime (No M.Sand to be used) over the RCC roof slab, the proportion of brick jelly to lime being 31:12.5 by volume laid over in a single layer and consolidated to the required designed and finished thickness by beating the concrete with wooden of beaters of approved pattern, keeping the surface constantly wet by sprinkling water, etc. complete as directed by the Engineer-in-charge. For Ground Floor

For First Floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M.Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,i/c., before use on works).

Providing plain cement concrete 1:2:4(one cement, two M-sand, four aggregate) using HBG jelly of size 20mm gauge for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and fixing in position best approved of ISI quality of the 110 mm dia of PVC rain water down fall pipes having a working pressure of 4 Kg./sq.cm including cost of necessry PVC shoe, PVC bend, C.T. gratings of required diameter and special clamps, brass screws, nails, etc. and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc. complete. The rate shall be inclusive of cost of removable iron grating. The PVC pipe shall be fixed in wall with special type of clamps. Special type of "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0 M pipe length complying with standard specification.

Supplying and fixing in position by means of 75 mm long and 65 mm dia counter sunk bolt and nuts embedded in the floor with rubber or fiber washer white glazed European Water Closet white colour with 100 mm "P" trap with double flapped rigid PVC black seat and seat cover with C.P. brass hinges including supply and fixing 10 litres capacity PVC low level flushing tank with a pair of C.I. brackets, etc., complete with all fittings such as 15 mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40 mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15 mm brass connections, 15 mm G.M. wheel valve, 15 mm brass nipple (2 Nos.), 15 mm nylon connection and fixing the low level ISI marked flushing tank with T.W. plugs and screws and giving necessary connection to the CI / PVC pipe including cost of 600 mm length of 100 mm dia C.I. Pipe and painting the C.I. Brackets with 2 coats of approved paint over one coat of red oxide primer and redoing the dismantled masonry to original condition etc. complete. (The EWC and flushing tank should be got approved by the Executive Engineer before use on works: Make: Parry ware / Hind ware or its equivalent))

Supplying and fixing in position CP Two way bib cock with Health faucet of best approved quality and approved make etc.,complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Providing & fixing first quality white vitreous china oval / round / square wash basin (size as per architectural drawing) for under counter mounting, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required. Vanity counter top type. (rate including the granite counter, size as per drawing and RCC slab wherever necessary)

Supplying and fixing in position of ½” dia 2 in 1 / C.P. wall mixer unit of approved make and quality (Jaguar / equivalent) including cost of cutting threading of pipes and fixing the GI pipe in position with white led, spun yarn etc., complete complying with standard specifications. (The C.P. wall mixer unit to be used on work should be got approved by the Engineer,i/c., before use on work)

Supplying and fixing Shower Rose with arm of approved make and best quality including labour charge for fixing and finishing, etc. complete complying with standard specification.

Supplying and fixing in position best quality brass chromium plated towel rail of 600mm length 20mm dia with CP brackets of same materials including fixing with necessary T.W. plugs, brass C.P. screws and dismantling masonry etc., complete with standard specifications. (The towel rail should be got approved by the Departmental officer before use on works).

Supplying and fixing in position 15 mm dia C.P. long body tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supplying and fixing of White Porcelin Sink of size 600mm x 450mm x 200mm with 32mm dia 'B' Class G.I. waste water pipe and 32mm dia C.P. waste coupling.including labour charges etc., complete complying with standard specification.

Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493.Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required or (b) Fixing/supporting the pipes (& fittings) at wall/ceiling level supported by galvanized clamps, hangers etc, as per specification. Exposed pipes to be painted of legends with direction arrow. GI pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the fire rated walls / floors slab and sealing the sleeves with glass wool in between and fire sealant compound at either end all as per Project Manager's / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings. 15mm dia CPVC pipe

20mm dia

25mm dia

32mm dia

Supplying, laying and jointing UPVC pipe of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications. (The UPVC pipe should got approved by the Engineer,i/c., before use on work). 40mm dia UPVC pipe With ISI Mark

50mm dia

65mm dia

Providing and fixing in position 100mm PVC .Multi inlet Floor traps with CP grating, joining, embedding in concrete etc. complete rate to include making of opening in floor, marble / tiles, for fixing grating. Size 150 mm x 150 mm

Supplying and fixing in position the following UPVC specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and pipes jointing the special complete complying with standard specifications. (The PVC specials used on the work shall be got approved by the departmental officer before use on work).50mm dia UPVC Elbow With ISI Mark

40mm dia Elbow

50mm dia Tee

40mm dia Tee

50mm dia Coupler

40mm dia Coupler

Supplying and fixing in position CPVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification. (The specials should be got approved by the Engineer,i/c., before use on work). 32mm dia CPVC Elbow With ISI Mark

25mm dia Elbow

20mm dia Elbow

15mm dia Elbow

32mm dia Tee

25mm dia Tee

20mm dia Tee

15mm dia Tee

32mm dia Coupling

25mm dia Coupling

20mm dia Coupling

15mm dia Coupling

32mm dia Union

25mm dia Union

20mm dia Union

15mm dia Union

Supplying and fixing in position PVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification. (The specials should be got approved by the Engineer,i/c., before use on work). 4" dia PVC Door bend With ISI Mark

4" dia PVC Plain Bend

4" dia PVC Door Tee

4" dia PVC Plain Tee

4" dia PVC Plain Elbow Tee

4" dia PVC Door Y

3" dia PVC Door Bend

3" dia PVC Plain Bend

3" dia PVC Door Tee

3" dia PVC Plain Tee

3" dia PVC Door Y

Supplying and fixing in position best approved quality C.P. brass soap tray of size 150 x 150 mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position Indian make decorative type wooden framed Mirror of approved quality and brand of size 600 x 450 mm x 5.5 mm shelf type with necessary ply wood backing, rubber buttons, brass CP screws, T.W. plugs etc. complete complying with standard specification. (The mirror should be got approved by the Departmental Officer before use on woks)

Cement Concrete 1:3:6 (One Cement, three M.Sand and six hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling 40mm broken brick jelly for septic tank dispersion trench filling including laying, spreading etc., complete with standard specification and as directed by the Engineer,i/c.,

20 mm size broken Brick jelly

Supplying and fixing of stainless steel sink size 2’-0’’x2’-0”x1’-0” of good quality and with a pair of M.S. angle, brackets, 40mm PVC waste pipe with necessary coupling T.W. plugs, screws, washers, white lead, etc., including painting two coats including dismantling the masonry if necessary and recovering the same to the original condition as directed.

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best approved quality of size 430mm x 260mm x 350mm with GI pipe connection, PVC waste pipe fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory if necessary and re-doing the same to the original condition as directed complying with standard specifications.

Supplying and fixing 15mm C.P. two way tap. The rate including all materials and labour charges, etc.of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supplying and fixing in position 15 mm dia C.P. short body tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supplying and fixing of Stainless steel Health faucet with necessary fittings and Labour chayges for fixing and Transportation charged etc., of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supplying and fixing of Black granite slab of approved colour and quality with base plastering in cement mortar 1:3 [One cement and three sand] 20mm thick and pointing the slab with coloured cement to match the colour of the slab, finishing neatly, cleaning the surface neatly etc., complete and as directed.

Supplying and Fixing of Cast Iron Manhole Cover of size 0.60x0.60m including transporation and labour charges etc., and all other charges for shifting fixing finishing neat etc complete. (The M.H cover should be got approved by the Departmental Officer before use on the works)

Providing expansion joint in RCC floor slab for 25 mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed

Providing expansion joint of 25 mm wide in between RCC twin columns from top of pedestal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealants for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Supplying and fixing in position 15 mm dia C.P. Screw down tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supply laying and jointing PVC pipe with ISI Mark of approved quality and make of the following dia fixed on walls with necessary clamps and screws including cutting and threading wherever necessary, etc. complete complying with standard specification and as directed by Engineer-in-charge. (Below Ground Level) 63 mm dia

50mm dia

40 MM dia

32 MM dia

25mm dia

75mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate valve and wheel valve with ISI make of the following size. (The specials should be got approved by the Departmental Officer before use on work). 63mm dia Gate valve With ISI Mark

50 MM dia

40 MM dia

32mm dia

25mm dia

20mm dia

15mm dia Gate valve

Providing rain water harvesting pit by earth work excavation in circular shape of 90 cm dia at 100 cm depth. The pit is encased with well ring of 90 cm dia , 30 cm depth, 50 mm thick using RCC 1:2:4 using 20 mm metal for 4 nos. The entire depth ie. 120 cm is filled with 40 mm size metal. The top of the pit is covered with RCC 1:2:4 50mm thick perforated slab including cost and fabrication of reinforcement grills for ring and cover slab, labour charges, cost of materials, moulding curing, finishing and fixing in position etc. complete.

Providing Granolithic floor finish for 25mm thickness with plain Cement Concrete 1:2:4 (One cement, two M.Sand, and four stone jelly) using 10 mm to 12 mm hard broken stone jelly and the top surface shall be rubbed smooth in all floors, finishing, threading and curing etc., complete complying with standard specification.

Supplying and erecting of 2000 litre capacity PVC Sintex water tank to ISI standard of approved quality and make including labour charges for fixing etc. complete.

Supplying and erecting of 5000 litre capacity PVC Sintex water tank to ISI standard of approved quality and make including labour charges for fixing etc. complete.

Manufacturing supplying and fixing of STEEL DOOR with following section. Outer frame 40 X 40 X 6mm Hollow steel special extruded section at 3.28Kg/RM and shutter frame 35 X 35 X 6mm hollow steel special extruded section at 3.28Kg/RM. Stiffeners with 32 X 6mm at 1.5 Kg/m MS flat is provided as the lock rail of the door and welded in fact on both ends to shutter frame. 20 gauge CR sheets of best quality is laid as panel in the shutters frames. 18X5mm at 0.7 Kg/m MS flat is welded over the 32X6mm at 1.50 Kg/m MS that on the rear side of the sand witching the CR sheet for rigidly. Additional stiffness with 18 X 5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter 2 Nos., of hinges in case of single leaf and 4 Nos., of hinges in case of double leaf shutter is provided 6 Nos., of hold fasts 120mm length spliced at the ends are welded to the outer frames of the door. Tower bolt 2 Nos., one at top and the other at bottom are provided. One aldrop is provided in case of double leaf door at lock rail section in the door. For single leaf doors one more aldrop is provided in the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at in appropriate place, in case of a double leaf door, MS flat 32 X 3mm at 1.10 Kg/m is provided on the edge of one shutter, to conceal the gap between the shutters. A tic bat is provided at the bottom of the outer frame to prevent twisting of frame during transportation of fixing. All members are given a shop coat of red oxide primer etc., as directed by the departmental officers. The rate is include cost of all materials, labour charges, transportation, taxes and all other incidental charges etc., complete.

Supplying and fixing of steel window covered with MS sheet openable shutter. The outer frame and shutter made out of steel sections confirming to IS7452/1982. The outer frames of windows made out of 'Z' section (F7D) of size 20x20x3mm confirming to IS 7452/1982. Mullions are made out (F4B) T section of size 46x25x3mm confirming to IS 7452/1982. The shutters are individual and each of themcanbe operated separately. Sash bars are made of "T" section (T2) of size 25x22x3mm. 2 Nos. of sturdy hinges and one number of handle cum ratch of special type are fixed or each openable. Suitable oipenings is left for its easy operation. One number of window adjustable string withfixing bracket of sufficient length are provided for each shutter 4 Nos. of 40x40x3mm angle holdfasts of 230mm inner face of the window at equal intervals not excluding 10cm spacing the shutter portion be covred with 20 gauge MS sheet. All members are painted withone coat of red oxide primer.

Design, fabrication, supply and erection of push and pull type rolling shutter with ISI mark at site of work made out of certain using 18G x 3" lath section bright CRCA strip in one piece without any welded joints at 76mm rolling centers interlocked with each other ends locked with heavy type cast iron / MS clips complete with lock plate using 10g MS sheets reinforced with 40mm x 40mm x 6mm MS angles at bottom and fitted with heavy letches and locking arrangements and handle on either side with pulling lock including necessary hood cover using 0.90mm CRCA sheet reinforced with 25 x 25 x 3 MS angles or gate channel. The roller shall be of heavy cast iron pullys, fitted with heavy duty. 'C' class 40mm steel pipe and high tensile carbon coil springs (2 springs should be supplied) with all accessories, etc. complete. The rolling shutters shall be fixed with pressed guide channels of 10G MS sheet and attached to the side brackets with 20mm square bar. Side brackets shall be 10G MS plates and cast iron 'U' clamp shall be riveted to the side brackets. The rolling shutters and accessories should be as per IS 6248 / 1979 specifications. The rolling shutter should be with two numbers of brass side locks and one number of brass centre lock with duplicate keys with necessary guide brackets for the locks, etc. The rolling shutters shall be coated with heavy coat of red oxide primer including inside portion of hood, etc. complete and as per the direction of departmental officers.

supplying and fixing of fish net above pasture field including tying by necessary materials the rate incluiding cost of all materials labour charges etc.complete.

Supplying and fixing of green net over the azolla unit area including transport and labour charges etc.complete.

Supplying and fixing of UPVC(Un-plasticized polyvinyl Chloride)windows of casement type (open) from the profile the size of outer frame 60mmx 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber( black colour) covered with over all the edges of frame and shutte the shuttter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not alllow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing allround the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing in position best quality PVC soil waste pipes of various size having ISI mark and pressure of 6 Kg/Sq.cm providing leak proof joints with PVC adhesive etc. including fixing to the walls with necessary T.W. plugs, brass screws mild steel clamps etc. and giving connection to the sanitary fittings including dismantling brick masonry /RCC works / roof slab etc. wherever necessary and making good the dismantled portion to the original condition, complying with standard specifications etc. complete (The PVC pipe should be got approved by the Departmental Officer before use on works).- 75mm dia pipe

110mm dia pipe

Supplying and fixing PVC end cap of size 160mm dia of approved brand and quality, etc., complete.

supplying and fixing of 160mm dia Gun Metal Gate Valve of approved brand and qunlity etc.complete

Supply and fixing country wood scantling (first quality paddock wood) for door frames including labour charges for making, applying anti corrosive paint on the back sides of frame and fixing the frame in position, etc. complete complying with standard specification. (The wood have to be got approved by departmental Engineers before use on work).

Supplying and fixing flush door shutters of single leaf with skin type paneled door made up of hard wood of approved quality including fixing necessary furniture fittings such as iron oxide MS hinges of 125mm x 30mm size 3 Nos., aluminium aldrop of size 250 x 16mm – 1 No. aluminium tower of size 25 x 12mm – 1 No. Aluminium tower bolt of size 200x12mm – 1 No., D type aluminium handle of size 125mm – 2 Nos.Aluminium door stopper / magnet catch 3” depth – 1 No. respectively, etc. complete complying with standard specification.

Painting new wood work with two coats of synthetic enamel ready mixed paint of approve quality and colour over a priming coat in all floors. The rate is inclusive cost of all materials and labour including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,,i/c., before use on works).

Casting and fixing of RCC Precast slab of 50mm thick in Concrete Cement 1:2:4 (One Cement, two sand and four stone jelly) using 20mm broken granite stone jelly excluding cost of reinforcement grill in position but including moulding charges, casting of jally, finishing, curing, fixing the jally in position and pointing the joint with C.M 1:2 in full depth in all floor etc., complete complying with standard specification.

Flooring with cuddapha slab of 50mm thick both side machine polished edge and machine polished cutting for flooring using CM 1:3 including labour charges for fixing etc., complete complying with standard specification.

supplying and fixing and fabrication of GI pipe with ISI Mark of required size and welding as per the engineer instruction. The rate includes welding charges,true vertical alignments, Labour charges, transport etc.complete 75mm dia GI pipe

65mm dia GI pipe

Supplying and fixing position PVC Nahini trap of 110 x 75 mm size with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime, concrete 1:2:5 (One part of lime, two part of sand and five part of 40 mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the damaged portions to the original condition and giving connection to the PVC pipes as directed etc. complete complying with standard specification. (The PVC Nahani trap should be got approved by the Departmental Officer before use on works)

Providing inspection chambers of various sizes using 9” thick brick walls using second sort table moulded chamber burnt bricks of sizes 9”x 4½”x3” in Cement Mortar 1:3 (One cement and three sand) 12mm thick and outside surfaces in C.M. 1:5 (One cement and five sand) 12mm thick. A precast cover slab of 75mm thick shall be provided for the chamber. The rate includes necessary earth work excavation to the required depth, Plain Cement Concrete 1:5:10 (One cement five sand and ten aggregate) 75mm thick etc., complete.-0.60x0.60x0.30 Mtr

size of 0.60x0.60x0.0.90 Mtr

Providing Pre - construction Anti - termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam, all round the Pile Caps, Catch basins, trenches, pits, tunnels, wall trenches, back fill, plinth filling, junction of wall and floor. External perimeter of building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. as per instructions of chemical manufacturer as directed by the Department officer/ Architect. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The work should be carried out by an approved and registered specialist pest control agency only. Tenderer to furnish the name of the proposed specialist firm. A 10 years post application guarantee against defects shall be furnished by the main Contractor. Note : Horizontal plan area at ground floor level of the building will be measured and paid.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers. (For Hatchery Building)

SS Associates

Bidder Name

SS Associates

CONTINENTAL CONSTRUCTION COMPANY