COMPREHENSIVE MAINT FOR OTM AND MD ACCN OF NURPUR COMPLEX, CAB MAMUN AND BUDHWAR ENCLAVE UNDER AGE B/R-I OF GE (S) MAMUN

Amount

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) on roof floors other than ground floors complete all as specified and directed.

Demolition of cement concrete (Re-inforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified & directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including brushing with neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified & directed.

Taking down cement plaster / wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified and directed.

Taking down shutters of any description exc. 1.00 sqm and not exc. 2.00 Sqm each, complete all as specified & directed.

Taking down shutters of any description not exc. 1.00 Sqm each, complete all as specified & directed.

Taking down, easing and adjusting shutters of any description, exceeding 1.00 Sqm and not exceeding 2.00 Sqm each and re-fixing in the same opening complete all as specified and directed.

M&L for brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specifiedand directed.

All as per description of srl item No 13.00 here-in-before but except bricks. Note: Servicable bricks retrieved from demolition of existing brick work shall be re-used.

M&L for brickwork with Fly Ash Bricks (old size), in half brick thick walls, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:4 complete all as specifiedand directed.

M&L for precast cement concrete louvres and jallies, 1:2:4 type B-0 (usng 12.5mm graded stone aggregates), 50mm thick (measured solid), set in cement mortar 1:4 including all mouldings but excluding frame complete all as pecified and directed. Note: Pre cast frame shall be measured & paid for separately

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ windows/ Ceosetory windows & other frames / Chowkaht of size 50 x 100 mm comprising of virgin PVC Polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solveng cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ cum, screw withdrawal strength of 2200N (Face), 1100 N (Edge), minimum compressive strength 58 N/ mm Sq, Modulus of elasticity 900 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixed in position MS hold fasts/ lugs/ SS dash fasteners of required dia and length complete, as per direction of Engr-in-Charge (Note MS hold fasts/ Lugs or SS Fasteners shall be paid separately) Note : For WPC Solid door/ window frames minus 5mm tolerance in demension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ windows/ Ceosetory windows & other frames / Chowkaht of size 50 x 125 mm comprising of virgin PVC Polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solveng cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ cum, screw withdrawal strength of 2200N (Face), 1100 N (Edge), minimum compressive strength 58 N/ mm Sq, Modulus of elasticity 900 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixed in position MS hold fasts/ lugs/ SS dash fasteners of required dia and length complete, as per direction of Engr-in-Charge (Note MS hold fasts/ Lugs or SS Fasteners shall be paid separately) Note : For WPC Solid door/ window frames minus 5mm tolerance in demension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ windows/ Ceosetory windows & other frames / Chowkaht of size 45 x 70 mm comprising of virgin PVC Polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solveng cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ cum, screw withdrawal strength of 2200N (Face), 1100 N (Edge), minimum compressive strength 58 N/ mm Sq, Modulus of elasticity 900 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixed in position MS hold fasts/ lugs/ SS dash fasteners of required dia and length complete, as per direction of Engr-in-Charge (Note MS hold fasts/ Lugs or SS Fasteners shall be paid separately) Note : For WPC Solid door/ window frames minus 5mm tolerance in demension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid one side decorative Flush door shutter of 35mm thickness comprising of virgin polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/ cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/ mm Sq, Modulus of elasticity 850 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, all as per direction of Engr-in-Charge (Note Stainless steel butt hinges and necessary SS screws shall be paid separately)

S&F factory made single extruded WPC (Wood Polymer Composite) solid Flush door shutter of 30mm thickness comprising of virgin polymer of K value 58-60 (Suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ weat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/ cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/ mm Sq, Modulus of elasticity 850 N/ mm Sq and resistence to spread of flame of Class A category with property of being termite / borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, all as per direction of Engr-in-Charge (Note Stainless steel butt hinges and necessary SS screws shall be paid separately)

S&F 35mm thick single piece Factory made wire gauge door shutters including wire cloth (steel & aluminium XPM) manufactured of 5mm thick PVC sheets printed on both side on frame made out of M.S tube 19 SWG, size 19mmx19mm complete in all respect with lock rail and beautified by PVC beading all around fixed with PVC solvent cement all as per Drawing No CEPZ/TD-378/, Sheet 1/1 dated 27/12/2011, as specified and directed

S&F 35mm thick 2nd class hard wood, glazed and skeleton door shutters, factory made, open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I, complete all as specified & directed.

S&F in repair factory made 25mm (+ 0.7mm) thick WPC board as in cupboard shutters / Shelves / partitions, prelaminated one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cum finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's instructions complete all as specified and directed.

Supply and fixing factory made uPVC white colour Sliding window, n exc 2 sqm in area, Three track made of extruded profiles with wall thickness of 2.3mm (+/-0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+/-0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

S&F Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes will be measured and paid seperately) with side hung shutters with MS handles and MS peg stay dovetailed or welded incl 02 Nos MS Tower bolts 150 mm long for each leaf and 8 mm square bar grill / guard bars at spacing as shown on Drg welded to MS flat iron frame work ,including other fittings, hinges, MS handles, tarred hold fasts, PCC blocks for hold fasts etc all as shown on Drg No CEPZ/TD -354/09 sheet 1/3 to 3/3 including two coat of synthetic enamel paint over one coat of red oxide zinc primer, complete all as specified and directed.

S&F hasp and staple 100 mm in size, aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish width of flaps (when open) 40 mm complete all as specified and directed.

S&F Stainless steel fasteners 75mm long steel supports, fixed to walls, complete all as specified & directed.

S&F Stainless steel designer handle (heavy duty) of 100mm size, fixed to drawers or cupboard shutters, complete all as specified & directed.

S&F Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed

S&F mild steel butt hinge 100 mm long, stainless steel, medium weight with SS hinge pin and fixed complete all as specified.

S&F aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed, complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section, length of bolt 150 mm and fixed complete all as specified and directed.

S&F aluminium handle, anodised of extruded section, 125 mm size and fixed.complete all as specified and directed.

S&F rubber lining fitted with aluminium powder coated strip, 100mm wide for door cill complete all as specified and directed.

S&F floor door stopper of 140mm long cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F Mild steel, 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete fixed with screw or necessary welding to pressed steel door frame complete all as specified and directed.

S&F stainless steel peg set of six of size 400mm x 30mm x 3mm fitted with machine screw and wooden and plastic cleats (minimum wt 190gms) complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from matel frame including punching or drilling out old glazing pins/spribng clips and providing and fixing new onces exc 1.5 Sqm complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane, complete all as specified and directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 guage with stainless steel brackets near to ends with stainless steel finials with adopter for 25 mm dia drapery rod at both ends complete all as specified and directed.

Taking up or down steel tubing of 15mm bore and connection, laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

M&L for cutting chases not exc 10 cm girth in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing etc. and making good, complete all as specified and directed.

S&F steel water tubing 15 mm bore medium grade galvanised, with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

S&F steel water tubing 20 mm bore medium grade galvanised, with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

Fixing only old steel tubing 20 mm bore and connections in new or old position (walls, ceiling, floor etc.) including taking up or down complete all as specified and directed.

S&F galvanised steel pipe 32 mm bore, light grade in short length as spout pipe, laid in brick wall in PCC 1:2:4 type B-1 for drainage of any seeped out water in sunken floor slab incl making hole in wall complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed refixing of inlet, outlet & over flow pipe etc. (Minimum weight of 20mm ball valve - 210 gms including dismantling of old brocken water tank complete all as specified and as directed.

S&F Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed refixing of inlet, outlet & over flow pipe etc. (Minimum weight of 20mm ball valve - 210 gms including dismantling of old brocken water tank complete all as specified and as directed.

S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball, screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight - 210 gm)

S&F Stop valve (ISI Marked), cast copper alloy with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fixed complete all as specified and directed..

S&F bib tap 15 mm bore long body, Brass CP, fancy type (long shank), with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F Stop valve /Angle valve (ISI Marked), fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron /PVC pipe or for unions of 15 mm bore and complete all as specified.

S&F in repairs CP Brass shower rose 200x200 mm size with with brass chromium plated flexible arm 450-550mm long complete all as specified and directed.

S&F in repairs Soap dish 120mm x 85mm (material SS finish, glossy) fixed to plugs with CP brass screws complete all as specified and directed.

S&F in repairs, Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision concrete bedding CI floor trap etc complete all as specified and directed.

S&F Vitreous china wash down water closet pan (Pedestal pattern) white (excl fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device complete all as specified and directed.

S&F in repair, plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device for pedestal pattern WC, black/ white colour complete all as specified and directed .

S&F in repair hand shower (Health Faucet) brass with 8 mm dia,1.2 m long Rubber flexible tube with Chromium plated spring type cover & Wall Hook for water closet complete all as specified and directed.

S&F in repair Centre hole basin mixer without popup waste system with 450mm long braided hoses cast copper alloy for iron pipes 15 mm bore, screwed for iron pipe and fixed and all as specified and directed.

S&F in repairs PVC flushing cistern, 10 litre capoacity, low level, push botton type dual flush type PVC valveless, syphonic action type, white, with inlet, ball valve, float and handle incl brackets & flush pipe PVC 32 mm dia complete all as specified and directed.

S&F in repairs sink with drainage board, made of stainless steel 1 mm thick, over all size 915 mm x 460 mm and bowl size 400mm x 300mm x 180mm with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe complete all as specified and directed.

Re-fixing only sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 180mm complete all as specified and directed.

S&F in repairs Vitreous china wash basin, flat back, white, size 550 x 400 mm excl taps, waste chain and plug and porcelain stopper but inclluding vitreous china pedestal and PVC waste pipe with union, 32 mm dia complete all as specified and directed.

S&F in repairs Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and all necessary fittings, complete all as specified and directed.

S&F corrugated waste pipe, 32 mm dia, suitable for WHBs/sinks/Urinal, including threaded PVC socket suitable for shank of waste coupling complete all as specified.

S&F in repairs Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F PVC connection 15 mm bore, 600 mm long, with PTMT nuts complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, dia of outlet in 75 mm, plain excluding grating, but including jointing with solvent cement complete all as specified and directed

S&F PVC grating square, 150 mm (Hinge pattern and with or without hole cpmplete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls cpmplete all as specified and directed. Note:- The measurement of pipes shall be net as fixed between the fittings including short lengths, without any allowance for cutting and waste or for the portions of pipes entering the sockets of the adjacent pipe or fitting. Fittings and accessories such as bends, branches, sockets etc. shall be enumerated afterwards and measured separately. Rates include for all necessary extra joints, cutting and waste.

S&F 110 mm bore PVC (SWR) bend any radius, with or without excess door complete all as specified and directed.

S&F in repairs, 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. Note:- The measurement of pipes shall be net as fixed between the fittings including short lengths, without any allowance for cutting and waste or for the portions of pipes entering the sockets of the adjacent pipe or fitting. Fittings and accessories such as bends, branches, sockets etc. shall be enumerated afterwards and measured separately. Rates include for all necessary extra joints, cutting and waste.

S&F 75 mm bore PVC (SWR) bend any radius, with or without excess door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for non-skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match, laid over and including 15mm thick cement screed in cement mortar 1:6, complete all as specified and directed .

M&L for non-skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but nexc 0.38 sqm as in skirting etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match, laid over and including 10mm thick cement screed in cement mortar 1:4, complete all as specified and directed.

M&L for non-skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match, laid over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

M&L for glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed with coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for Vitrified ceremic tiles, polished, light shade, 8 to 9mm thick (Square/rectangular) size 600mmx1200mm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar 1:6, complete all as specified & directed.

M&L for Vitrified ceremic tiles, polished, light shade, 8 to 9mm thick (Square/rectangular) size 600mmx1200mm, in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over & including 10 mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for 25 mm thick (average thickness) PCC 1:2:4, type B-0 using 12.5mm graded stone aggregates as in floor to required gradient/undulation, finished even and fair without using extra cement, complete all as specified and directed.

M&L for 18 to 20mm thick Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including circular cutting, chamfering of edges as required complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 18-20mm thick, size of each slab not less than 55cmx55cm, with 75mm wide white marble border alround, laid over & including 15 mm thick screed bed in cement mortar 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing using grinding macine to yield mirror finish complete all as specified and directed.

M&L for Machine cut Kota stone slab not less than 16mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing tusing grinding macine to yield mirror finish complete all as specified and directed.

M&L for non skid ceramic, parking tile, heavy duty coloured Endura tile dotted, of size 300mmx300mmx10mm, top layer glazed made in any type of cement and pigment, in required patterns in floor etc set & jointed in neat cement slurry & pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, complete all as specified and directed.

M&L for Machine Pressed, rubber moulded, precast concrete interlocking paver block any shape and size, red or yellow colour, M-35 Grade, 60mm thick confirming to IS-15658-2006 with grey cement and pigments, complete all as specified & directed. Note:- Sand cushioning shall be measured and paid for separately.

All as per description of serial item No. 92.00 here-in-before but except paver blocks. Note: Old retrived serviceable paver blocks shall be re-used.

M&L for 50mm thick sand cushioning using clean fine graded river sand under paver blocks, including watering and compacting complete all as specified and directed.

M&L for Chequered cement concrete tile 20cmx20cmx25mm thick, in floor, set and jointed over & including 20 mm screed bed in CM 1:4 and pointed in neat cement slurry with grey cement & pigment complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2, using 40mm graded stone aggregate as in sub-base to floors, finished even & rough to receive floor top finish complete all as specified and directed.

M&L for rendering 5 mm thick plaster in cement mortar 1:3 on concrete surfaces as in ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick plaster on fair faces of brick work or concrete surface in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 12mm thick plaster in cement mortar 1:4 mixed with and including WPC @ 200ml/50Kg of cement, on brick work and concrete surfaces of walls, surface finished even and smooth without using extra cement, complete all as specified and directed.

Taking down cement plaster and decayed concrete of any description from roof projection, chajja etc upto tripple storey of building, and making good the decayed portion with cement mortar 1 :3 mixed with & including water proofing compound as per manufacturer's instructions or PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including necessary form work and finally finished the surface with 15mm thick cement plaster in cement mortar 1:3, complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate as in plinth protection finished even and smooth using extra cement (incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper, white or tinted shade including priming and smoothing surface with 1.00mm thick cement based wall care putty complete all as specified and directed.

M&L for removal of existing treatment of walls, preparation of surfaces and applying two coat of oil bound distemper, white or tinted shade including priming and smoothing surface with 1.00mm thick cement based wall care putty complete all as specified and directed.

M&L for preparation of newly plastered external surfaces of walls applying two coats of cement based paint, white or tinted including curing before and after paint complete all as specified and directed.

M&L for preparation of old surfaces of walls of any description including washing down, rubbing, brooming down with wire brush, scrapping down smoke, roots, moulds, salts and treading oil and greasy spots, including taking down existing grass, vegetation, small trees and making good the disturbed surface with cement mortar 1:3 and applying one coat of cement based paint, white or tinted including curing before & after paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M&L for prepration of old steel surfaces of any description, not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

M&L for preparing of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for prepration of old wooden or wood based surfaces of any description, not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

Dismantling of plain or corrugated AC sheeting, any gauge, thickness, including ridge etc as in roof covering complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, bed plates benching, floor by maintaing required gradient / undulation etc slightly rounded or chamferred angles and throating, complte all as specified and directed.

M&L for mild steel structural steel as in roof trusses (framed), purlins, rails and heavy bracket frame (beam, tee, angle, channel or flat section) including distence pecies, cleats etc Gde Fe-410-W, Gde E-250, quality A complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour (as approved), having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour (as approved), having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 1.00 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 incl dismantling of existing valley/gutter etc complete all as specified and directed.

M&L for false ceiling with 8.00 mm thick gypsum tiles (600mmx600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed on and including T grid / Cross-T / Wall angle / level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

M&L for Use and waste of form work to soffits of WHB RCC counter, platform, suspended slabs such as roof slab, floor slabs landings and similar works etc, rough finished surfaces complete all as specified and directed.

M&L for mild steel TMT bars 8mm mm dia in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

M&L for cement concrete 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate as in slabs supported on beams, columns; floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed. Note : Reinforcement shall be measured and paid separately).

M&L for Pre-cast reinforced cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in cover slabs including necessary form work, set in cement mortar 1:6, complete all as specified and directed. Note : Reinforcement shall be measured and paid separately).

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. having minimum thickness of powder coating 50 micron incl taking down complete all as specified and directed.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.incl powder coating of any colour not less than 50 micron thickness complete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl Powder Coating of minimum thickness of powder coating not less than 50 micron complete all as specified and directed.

Taking down existing aluminium door/window shutter and refixing to same opening after repairing, easing and adjusting incl replacement of damaged hinges, brass mortice lock, sheet glass, door closer, Elco panel 4 mm thick, floor spring, rubber neoprene packing, aluminium beading, glazing clips and ss screws etc. complete all as specified Note:- Mortice lock, sheet glass, hydraulic door closer, floor spring and composit panel shall be measured and paid separately as Supply only).

Supply only Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed all as specified and directed.

Supply only Sheet glass 4.8mm thick, ordinary quality fixed with aluminium beading and rubber gaskeet exc 0.50 sqm each. all as specified and directed.

Supply only for Aluminium Mortice lock, 4 Lever, vertical type of size 100mm complete all as specified and directed.

Supply only for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

Supply only 4mm thick Aluminium composite panel for fixing to Aluminium shutter and the like squares with aluminium beading/gasketc complete all as specified and directed.

M&L for rendering 15 mm thick plaster in cement mortar 1:4 mixed with intergral water proofing compound and applying 75 mm thick padding and junction coved filling of PCC M-20 Nominal Mix (1:1.5:3) using 12.5mm graded stone aggregate on the junction of floor and wall the surface shall then be cured and allowed to dry, apply Epoxy Resins Coating, polymer Modified Cementation coating like brush bond of fosroc, pidilite and bostic as per manufacturer's instructions both on floor as well as on wall complete all as specified and directed.

Supply only liquid water proofing compound conformimg to relevant IS complete all as specified and directed.

M&L for cement concrete 1:5:10 type D-2 (using 40mm graded crushed stone aggregate as in mass filling in sunken floors of kitchens/toilets, complete all as specified and directed.

Cleaning/clearing of sewage line (including manholes) 100mm to 150mm bore of any description, underground at any depth, removing any type of blockage including desilting, descaling & dechocking of drains as well as manholes and depositing the sludge in a pit (including digging of pit) not less than 100 metres away from the site of cleaning and covering the sludge with layer of 2.5cm thick layer of earth and spraying unslacked lime on the pit and making sewage line smooth functional complete all as specified and directed.

Taking down existing roof treatment of any description incl mud phuksha or PCC padding of any description, any No. of layers including removal to debries in low laying area exc 1.00 KM but n exc 2.00 KM complete all as specified and directed.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specifications complete all as specified and directed :- (a) Cleaning the top surface of RCC roofing properly with water complete. (b) Applying Oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying of membrane not less than 3.0 mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160 Gms/Sqm using butane torch by torch application with 10 Cm side laps and 15 Cm end lap complete. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg /Sqm as prescribed by manufacture of membrane. (f) APP Membrane shall be sticked inside parapet where available by chase cutting and sealed with PCC (1:2:4) type B-0 complete.

S&F Wire netting made of stainless steel wire 0.71 mm dia with size of mesh 25mm fixed with tinned tacks of stainless steel wire staples complete all as specified and directed.

M&L for cement concrete 1:1.5:3 type B-0 (using 12.5 mm graded stone aggregate) as in leveling course on existing roof, rounded and chamfered on edges, mixed with & including WPC @200ml/ cement bag of 50 Kg complete all as specified and directed.

M&L for Strengthening and repair to RCC structural members such as column, beams, fins, Facia, chajjas & RCC slab as per the following precedence of application including necessary formworks and scaffolding if required upto 7 m height including dismantling loose/cracked plaster/concrete portion from RCC surface in any thickness as under complete all as specified and directed:- (a) Taking down the damaged/ loose concrete over existing structure and then making holes to existing structure to recieve slurry, Injecting and grouting to arrest leakage by using polymer based liquid water proofing compound mixed with cement @ 400 mili litre per 50 kg bag of cement in the water to form slurry, pumping the slurry through these holes one by one by using pressure pump till bleading the slurry and leave the surface for 24 hrs. (b) Applying one coat of steel bar coat of rust preventive PH RB-167/rust free/SHIELDOXY including preparing, cleaning of corroded steel all as per manufacturers instructions complete including providing additional reinforcement properly binded, overlap with the existing reinforcement and maintaining sufficient developement length/Anchorage length at the junctions to be inserted in the bearings of the R.C.C slab /RCC beam/RCC member to ensure/ acknowledge proper bond with the surrounding concrete complete all as specified and as directed by the Engr-in-Charge. (c) Providing/ filing the plain cement concrete 1:1.5:3 type A-0 (using 12.5 mm graded crushed stone aggregate) upto the depth/thickness varrying from 15mm to 45 mm. (d) Applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed. Note:- The additional reinforcement, if any required on the site shall be measured and paid separately under respective item of the BOQ.

Dismantling posts or struts (wood or R.C.C.) any section & Post Embedded in Natural Ground, including taking out embedded portion and making good disturbed ground complete all as specified and directed

Excavation in post holes (or similar holes) each n exc 0.5 cum in any type of soil getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded aggregate stone aggregate as in foundation and mass concrete complete all as specified

M&L for mild steel fencing posts/struts including embeding in concrete and screwing etc. including securing bolts; including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Fixing only chain link fencing including line wires of any mesh size, type and of any standard, rails, straining bolts etc including provision of binding wire complete all as specified and directed. Note: Supply of chain link fencing and S&F of FI support and MS round bars shall be measured & paid for separately.

Supply only chain link fencing of any mesh size, type and of any standard as approved including provision of binding wire complete all as specified and directed. Note: Weight of chain link fencing shall be ascerted through BOO convened by GE and the payment of item shall be made accordingly.

M&L for mild steel round bars 10 mm dia and over, cut to length, bent to shape required including cranking, bent to shape for stiffners etc and similar work complete all as specified and directed.

S&F mild steel screw bolts (machine made) 11 to 15 mm dia of shank with hexagonal or square heads at one end and screwed the other, each screw end to be fitted with washers and one hexagonal or square nut exc 5 cm but n exc 10 cm long complete all as specified and directed.

M&L for repair to steel door of built-in locker with attached shoe rack by easening and adjusting, welding/repaiing (if required) and replacement of mortice lock, handle cast brass100mm size, repair to vertical load (where required) locking arrangement including replacement of mortice lock , handle, cover plate (where required including preparing old steel surfaces and applying a coat of synthetic enamel paint complete all as specified and directed Note : Mortice lock, cover plate and handle shall be measured and pair under respective item as 'Supply only'

Supply only cup board locks grade 1, 2 lever size 65mm complete all as specified and directed

S&F handle, Extruded aluminium alloy, fabricated type, anodised 100mm size complete all as specified & directed

Supply only cover plate of 1mm thick MS sheet, of size 125x250mm including two coat of Synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M & L for Accessible , Sloped & Exposed Terrace, Deck Slab as under:- (a)Removal of Existing PCC/Brick Bat Coba/Mud phuska/ APP membrane from the roof stacking the reusable material and disposal of unserviceable ribbish out site the campus as per direction of the client with in 3 Km. (b) Cleaning of surface of loose dust and dirt cement slury etc. by means of wire brush, dust removing brush and scraper etc.In case of Pot Holes/ Cracks same shall be repaired with cement with cement admixed with Polymer as per manufacturer instructions etc. (c) Gola on Mother Slab: Providing and Making of PCC coving (gola) of size 75mm X 75mm with concrete Mix (1:2:40, cement sand, grit and including cost of mixing water proofing compund of approved make etc. complete as per direction by engineer in charge. (d) The surface shall be primer with Smart care epoxy primer to seal the pores and enhance the adhesion of the coating. Supplying and applying single component water proofing liquid membrane based on pure elastomeric, polyutherine resin smart care pu magnum us, cold applied of spray/ brush applied, membrane with elogation > 600% and tensile strength of 3-4 Mpa as per Astm D 412. crack bridging ability of 3mm as per ASTM C1305, no leakage upto 5 bars of water pressure as per DIN 1048, shore A Hardness > 50 Shore as per ASTM D 2240. The minimum thickness to be applied shall be 1.5mm. (e) Providing & laying of protective Geotextile fabric 150GSM over the entire membrane with proper overlaps of 75mm before of Brick bat coba treatment. (f) M & L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 20mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

Supply and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating over brick wall surface , Smartcare UltraBlock 2K or approved Equivalent Having>220% elongation as per ASTMD 2370, Resisting 5 Bars Hydostatic pressure as pepr DiN 1048, Reduction to rapid chloride shall be 70 as per DIN 1048, Craki bringing upto 3.50mm as per EN 1062. The coating shall have food grade certificate from laboratories like CFTRI. The Mixing ratio of Coating shall be 2 PArts of Powder & 1 Part of Liquid without any water addition in mixing etc. complete as per manufacturers specification. Mnimum consumption shall be 2 kg/Sqm. Supply and applying bond application MIX AP SC repair polymer and cement in RAtio of 1: Brush apply 1 or 2 continuous coat of Mix and ensure minimum consumption shall be 0.2 Kg/Sqm

M& L preperation of inaccessible roof surface by scrapping and properly cleaning the existing roof treatment in any number of layers upto original RCC roof top surafce. Apply first coat Fiber reinforced Elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index(SRI) of 100-110 , hsving minimum elongation of 350% tensile strength of 2.9 Mpa and shall have cracks bridging ability upto 2.5mm and shall resisit 10 bars of hydrostatic pressure reduce surface temperatureuoto 10 degree celsius with 33% dilution of priming coat. Laying of fiber mesh of 0.3 mm thickness weave in leno pattern having 45 gsm/Sqm and pasting it properly iwith overlap of 50mm and aloow it toodry.Apply second of undiluted coat @4.5 Ltr/Sqm. Apply third and final co for 10mm thick cement rendering in CM 1:E168at undiluted @0.45 ltr/sqm. Aplly third and final coat [email protected]/Sqm as directed by Engr in Charge. (a) M&L for 10mm thick cement rendering in CM1:3 and finishing the surface even and smooth before application of priming coat complete all as specified and directed

M/S Vijay Punj Constructions (BID ID -3335208)

Walia trading co (BID ID -3320993)

M/S CANTILEVER ENGINEERS (BID ID -3332759)

M/S TARA CHAND CONSTRUCTION CO. (BID ID -3326570)

AV ENTERPRISES (BID ID -3335540)