SPL REPAIR TO BLDG NO 121 WATER TANKS IN RWA-I LOC AND PROVN OF CERTAIN SANCTIONED WORKS AT NEW CANTT UNDER GE GANGTOK

Amount

Taking down cement plaster of any description on brick or stone walls incl raking out joints hacking for key, scrubing down with water etc. complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4Sqm complete all as specified and as directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

Demolition of concrete of any description and in any position not otherwise specially provided for complete all as specified and as directed.

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of dismantled materials/rubbish from site complete all as specified and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone agg) as in plinth protection/Path/hardstanding finished the concrete surfaces even and smooth without using extra cement etc complete all as specified and as directed.

M&L for 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed.

M & L for 20mm thick rendering in cement plaster in CM (1: 4) in two layer and top layer 10mm thick shall be mixed with WPC @ 3% by weight of cement on fair faces of stone masonry wall incl finish the surface even and fair without using extra cement (WPC shall be measured and paid separatly) complete all as specified and as directed.

Supply only Integral waterproofing compound complete all as specified and as directed.

M&L for 15 mm thick rendering plaster on fair faces of conc faces/ brick wall faces of smooth without extra cement in CM (1:6) complete all as specified and as directed .

M&L for applying two coat of exterior acrylic emulsion weather proof paint over a coat of primer on new/old plastered surface including preparation of new/old plastered surface etc complete all as specified and as directed

M&L preparation of new or previously untreated wooden surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint (1st grade quality) over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall suface on a coat wall care putty complete all as specified and as directed.

M&L for preparation of coplete removal of existing treatement on old plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over old wall surface on a coat of 2mm thick wall care putty, complete all as specified and as directed.

M&L for preparation of old or previously treated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamal paint (1st grade quality) over old steel surface complete all as specified and as directed.

S&F Powder coated grid frame work for false ceiling comprising of the following sections for making partitions of 600 x 600m size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 28mm x 23mm x 0.3mm thick, cross tee shall be 24mm x 23mm x 0.3mm thick and wall angle shall be 20mm x 20mm x 0.3mm thick complete all as specified and as directed.

M&L 4 mm thick E-board for insulation and accoustic purposes, 595 x 595 mm in size,fixed with staple on snap gird as in ceiling complete all as specified and as directed.

M&L for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded on chamfered put together with glue pinned and joints complete all as specified and as directed.

Supply and fix 2nd class Plain framed, panelled shutter (two panel) 35mm thick with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35mm thick 2nd class Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

Supply and fix Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw as in cup boards ,shelves etc complete all as specified and as directed.

S&F 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work etccomplete all as specified and as directed.

S & Ms but hinges 100mm long complete all as specified and as directed.

All as per item No 29 above but 75mm long complete all as specified and as directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

All as per item No 31 above but 100mm long complete all as specified and as directed.

S&F 150mm long Aluminium handles, cast type, anodised complete all as specified and as directed.

All as per item No 33 above but 100mm long complete all as specified and as directed.

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and as directed.

S&F stain less steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channels/drain including forming fair finished to drain channel complete all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors over and including 15mm thick screed in CM (1:6) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and as directed.

Ditto all as item No 40 above but on vertical surface of wall like skerting/dadoi etc on 15mm thick rendering in cm (1:4) complete all as specified and as directed.

M&L fo Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, , in floors over and including 15mm thick screed in CM (1:6) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and as directed.

M&L for glazed coloured ( 450 x 300 mm/250 x 350mm) x 7 mm thick as in skirting/dado over & including 10 mm thick rendering in CM (1:4) set & jointed in neat cement sullry & pointed in white or coloured cement to match complete all as specified and as directed.

M&L for lacquer coated precast chequered cement concrete tiles floor of size 200x200x25mm/300x300x25mm thick set and jointed in grey cement pigment to match over 15mm thick scteed bed in CM (1:6) complete all as specified and as directed.

M & L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed in CM (1:6) etc complete all as specified and as directed.

M&L for RCC(1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, cover slab, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. NOTE : Re-inforcement shall be measured and paid separately.

M&L TMT bars 10 mm dia & over cut to length bent to shape required, including cracking, bending spirally to proper for columns, hooking end & binding with and inch mild steel wire not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and as directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups cut to length, bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire(annealed) not less than 0.9mm dia complete all as specified and as directed.

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

M & L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick etc complete all as spfd and directed.

Taking down 15mm dia steel tubing and connections, including cleaning and refixing or removal to storecomplete all as specified and as directed.

Taking down 20mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

S&F galvanised steel water tubing 15 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

S&F galvanised steel water tubing 20 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floorscomplete all as specified and as directed.

S&F in repairs Water closet vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connecting to trap and flushing pipe anti syphon pipe etc provision of lime concrete bedding complete all as specified & as directed.

S&F in repairs 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed.

S&F in repairs vitreous china, white colour, wash hand basin of size 55 x 40 x 79cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling and making all necessary connectionscomplete all as specified and as directed.

S&F sinks made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair 15 mm bore dia angular Stop cocks, cast copper, fancy type, chromium plated, with wall flange screwed down, screwed fro iron pipe or union complete all as specified and as directed.

S&F in repair Bib tap , long body cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one complete all as specified and as directed.

S&F in repairs 15 mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and as directed.

S&F in repair chromium plated wall mixer 15mm bore with 115mm long bend pipe for connection to over head shower (with Bush & piston diverter fittings) with aerator screwed down for 15mm bore GI Pipe or for brass ferrule complete all as specified and as directed.

S&F in repair 15mm dia Brass CP mixer for mixing hot & cold water for sink screwed down for iron pipe and fixed complete all as specified and as directed.

S &F CP tubular towel rail 20mm dia D tupe 60cm long complete complete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Dismantling old PGI/CGI sheeting of any gauge thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete all as specified and as directed.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed by the Engr-in-Charge.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and as directed.

M&L for PCC (1:2:4) type B1 (20 mm gradeded crushed stone aggregate ) as in coping, bed plates , parepet,plinth course including weathering, slightly rounded or chamfered angles and throating,complete all as specified and as directed.

M&L for pre cast cement concrete(1:3:6) type C1 (using 20 mm graded crushed stone aggregate) block masonry with solid blocks, exc. 10 cm in width and settting in cement mortar (1:6) as per IS 383 complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out as in soft /loose soil complete all as specified and as directed.

Material and labour for hardcore of gauge n.exc.63mm (using broken stone or boulders) deposited, spread and levelled in layers not exc.15cm thick, watered and rolled/rammed to a true surfacecomplete all as specified and as directed.

M & L for 100mm thick Plain Cement concrete (1:2:4) type B2 (40mm graded crushed stone aggregate) as in hard stand /path etc including finish the surface even and fair without using extra cement etc complete all as specified and as directed.

Removing excavated soil to a distance n.exc.50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

Dismantling water tanks exc 500 ltr and n.exc 1000 ltr capacity and removing to store complete all as specified and as directed.

S&F rotational moulded polythylene water storage tank, 500 litres capacity, anti bacterial, UV and heat resistant 3 layer (ISI marked) multi layer construction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 210 gms, with threaded cap/Lid including connection including dismantling of old unserviceable water tank complete all as specified and as directed.

S&F 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, 20mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F decorative type curtain rod ,chromium plated 25mm dia with fixing btackets ,stops and complete fittings including making good the surface were damaged complete all as specified and as directed.

Taking down plastering on lathing (other than wire-netting), without removing lathing, in Cement mortar (one side only measured in cases where both sides are plastered) complete all as specified and as directed.

Excavating in trenches in soft/disintigrated rocks, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in in soft/disintigrated rocks complete all as specified and as directed.

M&L for plain Cement concrete (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete for tank staging complete all as specified and as directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and as directed.

M&L for PCC (1:2:4) type -B-0 (using 12.5 mm gradeded crushed stone aggregate) as in coping, or filling gap between gable wall and galvalume sheet etc. including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for Preparing surfaces plastered or unplastered new undecorated surfaces of wall and apply two coats of white wash complete all as specified and as directed.

M&L for 15mm thick rendering in cement plaster in CM (1: 4) in two layer and top layer 5mm thick shall be mixed with liquid water proofing compund @ 100ml/bag of cement of 50 kg on fair faces of stone masonry wall incl finish the surface even and fair without using extra cement (water proofing compound shall be measured and paid separatly) complete all as specified and as directed.

M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed.

Taking down 25mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

Refixing of old 25mm bore steel tubing and connections in new or old position (wall, ceiling or floor, etc) complete all as specified and as directed.

Supply and laying galvanised steel water tubing 25 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

S&F rotational moulded polythylene water storage tank, 1000 litres capacity, anti bacterial, UV and heat resistant 3 layer (ISI marked) multi layer construction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 25mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 455 gms, with threaded cap/Lid including connection including dismantling of old unserviceable water tank complete all as specified and as directed.

S&F in repairs Gun-metal, globe or gate valves, 25mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs Ball brass valves 25mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F Rolled mild steel of Fe 410 -W (GdeE- 250) quality A in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete all as specified and as directed.

S&F 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 gm/sqm complete all as specified and as directed.

M&L for applying two coats of synthetic enamel (ordinary tint) over a coat of red oxide zinc chrome paint including preparation of newly untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins, post, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-290 (Gde E165) etc complete all as specified and as directed.

M&L for 5 mm thick cement plaster (1:3) on fair faces of brick work or concrete surfaces in ceiling and finishing the surface even and smooth (without using extra cement) complete all as specified and as directed.

M&L for applying three coats of white wash on new plastered surface including preparation of new and previously untreated surfaces of ceiling/wall all complete all as specified and as directed .

S&F Anodised aluminium snap grid frame work size 605x605mm for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

M&L preparation of old or previously treated wooden surfaces of any description over 10 cm width or grith and applying one coat of synthetic enamel paint (1st grade quality) over one coat of pink primer on wooden surface complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cm in thick as in soft/loose soils complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specifed and as directed.

M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc; vertical or to better in rough finished surfaces complete all as specified and as directed.

M&L for Plain cement concrete (1:3:6) type C-2 (using 20mm graded crushed stone aggregate) as in retaining walls etc complete all as specified and as directed.

Hand packing (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed.

S&F for PVC(SWR) pipe 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floor with necessary clamps, bolt, bends, Tee complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in coping complete all as specified & as directed.

M&L for rendering 15 mm thick in CM (1:4) on other than fair faces of concrete surfaces, finished even & fair with using extra cement complete all as specified and as directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade complete all as specified & as directed.

S&F PVC half round 150mm dia pipe with rounded edges including all accessories/ fittings like T , Y etc for eaves gutter complete all as specified andas directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall, laid in trenches or in floor with all necessary clamps,bolts, bends, Tee etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

E/M Portion: Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and as directed.

Taking down carefully copper/aluminiumsubmain wiring of any size single core including earth wire and pvc conduit/casing capping and removing materials on site and making good the surface of wealls etc complete all as specified and as directed.

Taking down carefully unserviceable boaerd of any capacity incliding woolen board and making good the distrurbed surfaces of wall,etc including twon coat of white /colour washing/distempring etc match the existing complete all as specified.

M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) one light point controlled by one, one way switch, with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed.

All as per srl item No 122.00 here-in-above but one 3 pin 5 amps switch socket outlet point on independent board complete all as specified and as directed.

All as per srl item No 122.00 here-in-above but one 3 pin 6 amps switch socket outlet point on same board complete all as specified and as directed.

All as per srl item No 122.00 here-in-above but one bell/buzzer point controlled by one push button on same board with other switches or independent complete all as specified and as directed.

All as per srl item No 122.00 here-in-above but wiring with 2.5 sq.mm multistranded cable and earth wire with copper conductor 2.5 Sqmm complete all as specified and as directed.

All as per srl item No 122.00 here-in-above but wiring with 4 sq.mm multistranded cable and earth wire with copper conductor 4 Sqmm complete all as specified and as directed.

Supply and fix switch piano flush type single pole , one way 6 Amp 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Socket outlet 2 in 1, 3 pin ,6A 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Socket, outlet 2 in 1 , 3 pin , 6 Amp and 16 amp flush type 230 V 50Hz,ISI marked complete all as specified and as directed.

Supply and fix switch piano flush type single pole , one way 16 Amp 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fixing of bell electric Ding Dong type, Ac 230 volts fixed complete all as specified and as directed.

S&F ceiling rose, 3 phase ,PVC polycarbonate ,insulated body (ISI Marked) complete all as specified and as directed.

Supply & fixing LED lights fitting 1x18 watt 220 V, AC decorative box type with driver , holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply & fixing LED Mirror lights along with fixture ,5 watts with suitable fixing arrangement complete with all as accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable sizecomplete all as specified and as directed.

Supply & fix lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as specified and as directed.

Supply & fixing LED lights fitting 1x9 /1x10 W 220 V, AC bulk head luminaries including , holder including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Taking down and refixing of Geyser storage type after completion of civil work 25/50 ltr capacity complete with grounding /drilling in wall and provn of Zink coated fastener 12 mm dia 150 mm long x04 Nos including replace hot & cold PVC pipe complete including nuts/bolts ,painting and complete testing complete all as specified and as directed.

S&F single pole & neutral enclosure with a two pin & earth plug & socket complete with one single pole MCB C curve of 20 A rating complete all as specified and as directed

S&F for MCB DB TPN 4 ways Single Door with 200 Amp rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed. Make :- havells/legrands/C&S

S&F for MCB DB SPN 8 ways Double Door 240 Volt with 200 Amp rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed.

S&F MCB single pole & neutral SPN 40 to 100 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

S&F MCB single pole & neutral SPN 32 Amps to 63 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

S&F MCB single pole 6 to 32 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

supply and fix of sub main wiring with two run of 6.0 Sq. mm PVC sheathed, copper conductor cable, 1100 Volt, FRLSH grade and one run of copper earth wire 6.0 Sq mm drawn through PVC casing and caping, complete all as specified. Note : Copper conductor 2 run and one run of copper earth wire along with PVC casing and caping shall be measured as one length complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level connected with galvanised iron/steel earth wire of 4 mm dia by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to DBs including necessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC (1:2:4) type B1 chamber with 40mm thick RCC (1:2:4) type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS Hook 6mm dia MS bars etc including testing on completion complete all as specified and as directed.

Supply and fix aesthetically designed 2X2 LED flat panel for ceiling mounting which provides soft light and glare free illumination not less than 36 watt,efficiency >125 lm/ W, including and connecting up complete all as specified and as directed. Make Havells cat part No.VENUSNEO2X2PLR36W LED865PO/ Crompton cat part No. TCR-145-36-65-SL-NWH/ Philips cat part No. RC360B LED36S-6500 V1 L60W60 PSU OD

Supply and fix LED wall light 1x20w 220 V AC holder with LED bulb suitable for 20 W LED retrofit lamp B22 base with connecting up with three core flexible copper conductor complete all as specified and as directed.

Supply and laying of DWC pipe,ISI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket,bend,couplers etc confirming to IS 14930,part-II complete with fitting cutting,jointing etc of size 40 mm outer dia complete all as specified and as directed by Engr-in-Charge.

Supply, Laying, jointing & testing in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, cross sectional area of 6 Sqmm 3 core complete all as specified and as directed.

S&F bore 40 mm pipe galvanized iron medium grade complete with all fittings fixing on wall, jointed tested and commissioned complete all as specified and as directed.

M&L for cutting the existing hard standing/PCC/WBM road at a depth not less than 45cm and 25cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing cement concrete (1:2:4) type B-2 (using 40mm graded stone aggregate) upto 20cm depth, finising to a uniform smooth surface to match the existing surface complete all as specified and as directed. Note: (i) GI pipes shall be measured and paid separately (ii) Any damages made/caused to the HT/LT cables, water supply pipe lines, OFC cables etc during the excavation work shall be made good by the contr as per original and to the entire satisfaction of the Engr-in-charge. Cost of the same is deemed to be included in the unit quoted rated.

KAMLESH ENTERPRISE (BID ID -3276199)

M/S ANIL KUMAR THAKUR (BID ID -3276324)

BIJAY MITTAL (BID ID -3276078)