ADDITION ALTERATION TO 100 ORs MARRIED ACCOMMODATION AT MCEME UNDER GE MCEME SECUNDERABAD

Amount

B/R ITEMS

Demolition of cement concrete (unreinforced) of any description and in any position (as in roof paddings etc) not otherwise specifically provided for including removal of debris to outside MD land.etc., complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc., but excluding ashlar facing etc., complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thick below or above GL including removal of debris to outside MD land.etc., complete all as specified and as directed.

Dismantling of floor hearth or wall tiling or terrazzo flooring including cement mortar bedding (but not backing) and removing rubbish off the premises to outside MD land etc., complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removal to store / taken on credit complete all as specified and as directed.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removal to store / taken on credit complete all as specified and as directed.

Taking down door / window chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down door / window chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area exceeding 1.5 Sqm and not exceeding 4.0 Sqm each complete all as specified and as directed.

Removing completely existing expansion joints between columns and walls, cleaning the surface & gap thoroughly with wire brush/coir brush and water jet, filling the gap with approved joint filling sealant, providing metal cradle made out of 0.60 mm thick Galvalume sheet and inserting 25 mm thick neoprime / thermocol /Shalitex pads and sealed with polysulphide sealent of approved make, minimum 40 mm deep 0.80 mm thick aluminium sheet shall be fixed over the joint with rawl plugs and cadmium plated steel screws etc., complete all as specified and as directed.

Cutting grooves in brick wall, 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 etc., complete all as specified and as directed.

Material and labour for providing Plain Cement Concrete 1:2:4, type B0, using 12.5mm graded stone aggregate laid to slope as in roof padding and finished the surfaces fair and even complete all as specified and as directed.

Material and Labour for 10mm thick cement screed in cement mortar 1:3 mixed with liquid water proofing compound as per manufacturer's instructions on roof slab/ floor etc., complete all as specified and as directed. Note: Liquid water proofing compound shall be measured and paid separately.

Supply only Integral Liquid Water Proofing Compound conforming to IS:2645-2003 complete all as specified and as directed.

Material and Labour for providing water proofing treatment with membrane type water proofing method using APP modified prefabricated five layer water proofing membrane mat finish, 3 mm thick and weighing not less than 3.5 kg/sqm reinforced with non woven polyester matt black weighing not less than 100 gm/Sqm, having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 300 N/Sqm, laid over one coat of bitumen primer at 0.20 Kg/sqm and torch application of membrane using gas burner with 150 mm overlap on side lap and end lap as per manufacturers instructions with top most layer of surface finished with two coats of solar reflective aluminium paint @ 0.10 Litre/Sqm per coat etc., complete including taking down/ remove of old bituminous treatment,existing tar felt of any thickness, cement lime plaster of any thickness of roof, PCC padding of any thickness, cleaning the cleaning the top surface of roof with wire brush and washing with hydrochloric acid to remove dust, dirt, oil, grease, loose particles, roughing surface to receive plaster and scrubbing down with water and dispose the debris exceeding 250m distance including dismantling of earthing strips and refixing the same after roof treatment all as specified and as directed.

Note for item No.14: (i) The work shall be executed through Manufacturer's authorised applicator approved by GE. (ii) The quoted rate is deemed to include the cost of digital photograph and plaster plate as per PS.

Material and labour for screed bed or bedding layer of mortar 20mm thick for laying floor finishes in Cement Mortar 1:6 etc., complete all as specified and as directed.

Material and labour for coloured Non Skid ceramic tiles of grade B-II(a), 7 to 8 mm thick (square/ rectangular), light coloured group, area of each tile exceeding 0.06Sqm but not exceeding 0.11 Sqm, laid in floors of pattern as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for coloured Joint free Anti Skid ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18Sqm but not exceeding 0.38 Sqm, laid in floors of pattern as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for Rendering 10mm thick in Cement Mortar 1:3 on as in backing coat for fixing tiles on vertical surfaces such as skirting, dado etc., finished fair and even complete all as specified and as directed.

Material and labour for coloured Joint free Anti Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) of size matching to floor tile as approved, fixed on vertical surfaces such as in skirting / dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match floor tile complete all as specified and as directed.

Material and labour for glazed coloured ceramic tiles of grade B-III, 7mm thick of size 300x200mm or of size matching to floor tile as approved, fixed on vertical surfaces such as in skirting/dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match floor tile complete all as specified and as directed.

Material and labour for brick work fly ash bricks straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM 1:6 complete all as specified and as directed.

Material and labour for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on brick work or stone walls / cement surfaces / ceiling plaster etc., including raking out of joint , hacking for key scrubbing down with water and removing debris to outside MD land etc., complete all as specified and as directed.

Material and labour for Rendering in Cement Mortar 1:6, 10mm thick on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering in Cement Mortar 15mm thick in two layers, i.e, in Cement Mortar 1:4, 5mm thick mixed with water proofing compound as per manufacturers' instructions over in Cement Mortar 1:6, 10mm thick on fair faces of brick surfaces, finished even and smooth etc., complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Material and labour for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work, chajja, facia, slabs etc in CM 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering to soffits of ceiling, etc., 5 mm thick in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Supply and fix in repairs vitreous china wash down water closet squatting pan, Orissa pattern of size 580x440mm with integral foot rest , colour white with and including P trap, lime concrete bedding and making necessary connection to soil pipes and flushing cistern etc.,complete all as specified and as directed.

Supply and fix Vitreous china wash down water closet pan, pedestal pattern, colour white, closed pattern with flat bottom with and including fixing bolts, white coloured PVC seat cover, mild steel chromium plated or aluminised hinging device and P/S trap including connections to drain (or outgoing pipe) and taking down existing water closet etc., complete all as specified and as directed.

Supply and fix in repairs health faucet (hand shower) chromium plated with 1.0metre long easy flex tube 8mm dia with wall hook as per Cat No.BEA-41 of Prayag or equivalent of other specified makes, screwed for two way bib taps etc., complete all as specified and as directed.

Supply and fix in repairs PVC valve less, syphonic action type, low level flushing cistern, 10 litre capacity, white, with accessories like inlet, ball valve, float, handle, brackets, PVC flush pipe, over flow pipe etc., including taking down the exiting one complete all as specified and as directed.

Supply and fix in repairs Vitreous china Wash Hand Basin, white, flat back of size 550x400mm including CI brackets, porcelain stopper, cutting for and pinning ends of brackets including waste fittings of brass chromium plated 32 mm (excluding waste pipe, taps chain and plug) complete fixed in repairs all as specified and as directed.

Supply and fix 16mm bore 3-layer PP-R (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

Supply and fix 20mm bore 3-layer PP-R (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

Supply and fix Bib taps 15 mm bore, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle confirming to IS screwed down, screwed for iron pipes or for brass ferrule, fixed in repairs all as specified and as directed.

Supply and fix Stop valve / angle cock 15mm bore, cast copper alloy, chromium plated conforming to IS with screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, fixed in repairs complete all as specified and as directed.

Supply and fix Stop valve / angle cock 15mm bore, cast copper alloy, chromium plated, fancy type with long shank and cup (concealed type) conforming to IS with screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, fixed in repairs complete all as specified and as directed.

Supply and fix in repairs PVC connection 15mm bore, length 600mm with brass nuts of superior quality complete all as specified and as directed.

Supply and fix in repairs Soap dish, Vitreous china white, approximate size 160 x 160 x 90mm, fixed to plugs with chromium plated brass screws fixed on walls etc. complete all as specified and as directed .

Supply and fix in repairs Stainless Steel tubular towel rail, 20mm dia, D type, 600mm long, Chromium plated with flanges fixed on wall with rawl plug and chromium plated screws complete fixed all as specified and as directed .

Supply and fix in repairs Brass chromium plated shower rose of size 125mm with swivel joints including shower arm 15mm size, 195mm long with bend of 45 degree with flange for fixing with 15mm dia pipe compete all as specified and directed.

Material and labour for Granite work (of any type) with 17-19mm thick machine cut, 'Z' Black granite slab in single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:6, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone including cutting, polishing and rounding to edges of stone slabs etc., complete all as specified and as directed.

Dismantling / Demolition and breaking of old PVC water tank of capacity 500 ltrs to 1000 ltrs with ball valve laid on RCC roof slab carefully without disturbing to existing roof/wall etc., complete all as specified and as directed. Note : If any damage occurred to existing roof / wall during demolition shall be made good by the contractor at his own and without any cost to department.

Supply and Fix, 500 litres capacity Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, 'ISI' marked, three layered (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) etc., complete all as specified and as directed.

Supply and Fix in repairs Gun metal globe or gate valve of size 20mm bore confirming to IS 778-1984 with iron wheel head, screwed both ends for GI pipe including all fittings / fixtures like nipple, union etc., complete all as specified and as directed.

Supply and fix Ball valve PTMT with epoxy coated aluminimum rod for 20mm bore pipe, weight not less than 210gms, high pressure with polyethylene high density float and complete screwed for iron pipe all as specified and directed.

Supply and fix in repairs Stainless steel kitchen sink of over all size 915mm x 460mm with drain board and bowl size 410mm x 355mm x 175mm made out of 1mm thick stainless steel sheet of grade AI SI-304 with plugs, washers, waste coupling and 40mm dia waste pipe, fixed over CI brackets or bedding in cement mortar to dwarf wall as required and connecting union to pipe including taking down of existing kitchen sink of any size compete all as specified and as directed.

Supply and Fix factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet and edges will be painted to match with prelam sheet, reinforced with 19mm MS square tube of 19 gauge mitred out at two corners and joined by inserting two Nos of 150mm long brackets of 15mm x 15mm MS square tube inside the drilling 100mm long MS screws using PVC fastener as per manufacturer's instructions complete all as specified and as directed.

Supply and Fix factory made Factory made solid panel laminated PVC door shutter 30mm thick (style) consisting of frame made out M.S tube for top & bottom rails. M.S Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled the stiles & rails with suitalble PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing complete all as specified and as directed. Note: Butt hinges, Barrer tower bolts, handles and sliding door bolts shall be measured and paid separately.

Supply and Fix 100 mm long butt hinges, extruded aluminium alloy with brass/bronze hinge pin complete all as specified and as directed.

Supply and Fix 150mm Extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

Supply and Fix 150mm long aluminium anodised barrel tower bolts of extruded section ISI marked complete all as specified and as directed.

Supply and Fix aluminium alloy anodised sliding door bolts 150mm long with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed.

Supply and Fix Windows/ Ventilators (NCL ECO-4000 Series Windows (Double Rebate Windows) or equivalent) fabricated from roll formed sections of size 72mm x 55mm for Frame, 72mm x 50mm for Mullion, 47mm x 20mm for shutter, 12mm x 12mm for fixed glass bead and 40mm x 20mm for Fly prof mesh made of galvanized steel colour coated/ powder coated (Base steel as per IS 513 “D” quality galvanized as per IS 277 with zinc of 120 gms/Sqm) with total coated thickness of 0.58mm, section for frame Glazed shutters and Mesh shutters cut to length and miter joined with Polypropylene Corner brackets, Mullion section joined with frame/mullion using Mullion Cap Ethyl Propylene Damien Monomer (EPDM) Gasket all around glass in shutter and Fixed Glass,

Spoon Section used around Fly mesh to fix Mesh in Mesh Shutter including provision of SS Pivot Hinges - 1 set, Seccolor Handle & Seccolor handle and stay and 5mm thick Plain Float Glass and Stainless Steel 32 gauge Fly proof wire mesh of 304 grade with 25 holes per SqCM and powder coated Grill made of 10mm sq. MS Bars welded at 150mm c/c, 6mm x 12mm MS flat and fixed to window frame with screws and frame shall be fixed to brick/concrete masonry by uing Nylon self-expanding caps and driving MS electroplated 80mm long screws in th caps through frames etc., complete all as specified and as directed. Note: Measurement shall be the size of opening and the unit rate quoted shall be deemed to include the cost of Powder coated galvalume sheet sections for frames, shutters, powder coated MS grill, jonting cleats, Stainless stell wire mesh for fly proof, 5mm thick sheet glass, glazing clips, EPDM gaskets, builders hardware etc.

Supply and Fix Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with fixed with stainless steel wire staples fixed to frames etc., complete all as specified and as directed. Note: Stainless steel wire cloth provided to windows and ventilators against item No.57 hereinbefore shall not be measured against this item.

Supply and Fix Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame complete all as specified and as directed.

Supply and Fix Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame complete all as specified and as directed.

Material and labour for Providing Plain Cement Concrete, 1:2:4, type B0, using 12.5mm graded stone aggregate as in filling inside the pressed steel door frames or chowkats complete all as specified and as directed.

Material and labour for Mild Steel work in bands, straps, supports of stays, sunshade brackets, hook and spintle hinges, clamps, hold fasts, guard bars, grills bolts etc and similar conforming to FE-290, Gde E 165 complete all as specified and as directed.

Material and labour for Second class Hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, supplied and fitted complete all as specified and as directed.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron works new or old treating ends of posts, back of chowkats etc with tar or coal tar black paint area tarred exc 0.1Sqm but n.exc 0.5Sqm each.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron works new or old treating small articles such as hold fast etc with tar or coal tar black paint area tarred n.exc 0.1Sqm each.

Supply and fix 35mm thick flush door shutters, solid core construction, with block board core and plywood face panels, commercial type face on both sides with lipping to match with frame and fitted to chowkats etc., complete all as specified and as directed.

Taking down door shutters of any description exc. 1sqm but not exceeding 2sqm each and refixing in same opening after cutting, easing and adjusting and refixing builders hardware as required including renewal of unserviceable builders hardware article and screws etc., all as specified and directed

Supply and Fix 2nd class hardwood factory made 35mm thick glazed and skeleton door shutters, open rebated and prepared to receive glass, gauge etc., without sash bars, edges of framing plain, chamfered, rounded fitted with cut and mitred beads for securing glass etc, size of members as specified in SSR Part 1 section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified and as directed.

Supply and Fix 100 mm long Stainless Steel Butt hinges with stainless steel hinge pin complete all as specified and as directed.

Supply and Fix aluminium alloy anodised sliding door bolts 250mm long with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed.

Supply and Fix Extruded aluminium alloy handles of size 150mm, fabricated type anodised complete all as specified and as directed.

Supply and Fix 200mm long aluminium anodised barrel tower bolts of extruded section ISI marked complete all as specified and as directed.

Supply and Fix MS helical door spring 300 mm long with roller and roller plate complete all as specified and as directed.

Dismantling boarding, cupboards shelves etc. of any thickness any description fixed in any position with nails/screws etc. complete all as specified and as directed.

Dismantling framed work of timber in fillets, rails, posts, rafters, purlins, etc. of cross sectional area under 40 sq. cm in section complete all as specified and as directed.

Material and labour for Second class hard wood Plain fillets, square, rectangular or triangular in section, wrought and smooth finish of cross sectional area exc. 13 Sqcm and not exc.25Sqcm secured with nails or brads including polishing etc., complete all as specified and as directed.

Material and labour for Second class hard wood Plain fillets, square, rectangular or triangular in section, wrought and smooth finish of cross sectional area exc. 6 Sqcm and not exc.13Sqcm secured with nails or brads etc., complete all as specified and as directed.

Material and labour for Second class hard wood Plain fillets, square, rectangular or triangular in section, wrought and smooth finish but bull nosed, splayed, chamfered or rounded on one edge or face of cross sectional area not exc. 3Sqcm as in beadings of cupboard shutters secured with nails etc., complete all as specified and as directed.

Material and labour for prelaminated Medium Density Fibre (MDF) board 17-18mm thick, exterior grade prelaminated on one side with decorative choice lamination and other side with balancing white lamination fixed in repairs with screws to timber framed work for cupboards, shutters, book shelves, kitchen cabinets, drawers etc., complete all as specified and as directed.

Material and labour for prelaminated particle board 25mm thick, exterior grade prelaminated on one side with decorative choice lamination and other side with balancing white lamination fixed with screw to timber framed work etc., complete all as specified and as directed.

Supply and Fix continuous piano hinges mild steel bright finish or electro galvanised Width of flaps 30mm (when open) and fixed with screws complete all as specified and as directed.

Supply and Fix 150mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

Supply and Fix Hasp and staple safety type aluminum anodised 100mm size with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply and Fix 40m dia cup board knobs fixed with nut, screw and washer of brass polished complete all as specified and as directed.

Supply and fix in repairs Mild steel Mortice lock of size 65 mm, 4 levers, vertical type, grade 1 with handle set suitable for cupboards all as specified and as directed.

Material and labour for Stainless steel designer Chromium plated decorative curtain rods (Drapery rods) 20mm dia, exterior grade 3mm thick with and including side caps, holding clamps and 'F' and 'L' brackets, fixed to wall with PVC rawl plug and brass screws etc., complete all as specified and as directed.

Material and Labour for Stainless steel designer curtain rod's brackets of approved quality with knob and pattern and fixed to wall with PVC rawl plug and brass screws etc., complete all as specified and as directed.

Supply and Fix sheet glass 3mm thick plain, ordinary quality, ground or obscured or frosted, on one side and glazing with beads/oil putty in squares not exceeding 0.50 Sqm in each pane etc., complete all as specified and as directed.

Supply and Fix UPVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to walls/ laid in trenches or under floors etc., including demolition and breaking up existing drain pipes and taking out out with fittings etc., complete all as specified and as directed . Note: The unit rate quoted shall be deemed to include the cost of Earthwork excavation, returning filling in and removal of surplus soil if required.

Supply and Fix UPVC (SWR) pipes 75mm bore, single socketed in any length with rubber ring joints fixed to walls/ laid in trenches or under floors etc., including demolition and breaking up existing drain pipes and taking out with fittings etc., complete all as specified and as directed . Note: Earthwork excavation, returning filling in and removal of surplus soil if required shall be measured and paid separately.

Supply and fix 110mm bore UPVC (SWR) bend any radius complete all as specified and as directed.

Supply and fix 75mm bore UPVC (SWR) bend any radius complete all as specified and as directed.

Supply and fix in 110mm bore UPVC (SWR) bend any radius with access door complete all as specified and as directed.

Supply and fix 75mm bore UPVC (SWR) bend any radius with access door complete all as specified and as directed.

Supply and fix UPVC (SWR) floor trap 75 mm dia outlet, plain with grating including joining with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) etc., complete all as specified and directed.

Supply and fix UPVC (SWR) Gully trap 125/110mm, setting and joining with solvent cement complete all as specified and directed.

Supply and fix 110mm bore UPVC (SWR) vent cowl complete all as specified and as directed.

Supply and fix in repairs Stainless steel Plate rack of size 1200mm x 900mm with separators and 3 tier shelves made out of 1.00mm thick stainless steel sheet of grade AI SI-304 fixed on wall with rawl plug and chromium plated screws complete fixed all as specified and as directed .

Supply and fix in repair 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 Kg/Sqcm in any length with rubber ring joint fixed to wall or in floors as in outlet pipe for WHB etc., complete all as specified and as directed.

Supply and fix in repair 40 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 Kg/Sqcm in any length with rubber ring joint fixed to wall or in floors etc., complete all as specified and as directed.

Supply and Fix in repairs Floor door stopper, 140mm overall length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and as directed.

Supply and Fix in repairs Shelf of PTMT of weight not less than 300 gms fixed with and including Chromium plated brass screws and wooden / plastic cleats etc., complete all as specified and as directed.

Material and labour for chipping of spalled cracked concrete by chiselling up to depth of 10-20mm from floor/roof slabs, chajjas, fins, facias and similar structural members etc., cleaning the dismantled portion with wire brush, emery paper etc., remove all traces of rust, scales any dust, oil, paint, grease by cleaning with water jet and prepare the structure for the application of high build polymer modified cement mortar and applying rust remover on affected steel surfaces by using cotton waste swap or by brush as per standard specification and manufacturer's instruction including necessary scaffolding and removal of debris to a distance not exceeding 50m etc., complete all as specified and as directed.

Material and labour for application of high build polymer modified cement mortar in the ratio 1:2.5 mixed with 3 kg SBR per bag of cement in ceiling surfaces 10 to 20mm thick in two layers surfaces over a coat of bonding agent Nito Bond SBR as per manufacturer's instructions on floor/roof slabs, chajjas, fins, facias and similar structural members etc., complete all as specified and as directed.

Demolition of Reinforced Cement Concrete in fins, fascia column edges including cutting reinforcement etc., complete all as specified and as directed.

Formwork to surfaces of RCC fins, fascia, chjjas and similar items including edges for flat fair finished surfaces of concrete complete all as specified and as directed.

Material and labour for Reinforced Cement Concrete, type A1, 1:1½:3 nominal mix concrete using 20mm graded stone aggregate as in fins, fascia, chajjas and the like complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of wall and applying 2.0 to 3.0mm thick white wall care putty to make the surface even and smooth finish, rubbing with sand paper of different grade etc., and applying two coats of Oil Bound Distemper over a coat of alkali resistant primer etc., complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of wall with electric operated blade, washing with water and applying 2.0 to 3.0mm thick white wall care putty to make the surface even and smooth finish, rubbing with sand paper of different grade etc., and applying two coats of Oil Bound Distemper over a coat of alkali resistant primer etc., complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of ceiling with electric operated blade, washing with water and applying for applying three coats of white wash including preparation of old surfaces complete all as specified and as directed.

Material and labour for applying three coats of white wash on ceiling including preparation of newly plastered surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment with electric operated blade, washing with water and bleaching powder solution on external surfaces of wall and applying two coats of weather proof exterior acrylic emulsion paint (Apex Ultima protek of Asian or equivalent of other specified makes) over a coat of sealant and exterior primer (or) base coat as per manufacturer's instructions etc., complete all as specified and as directed.

Material and labour preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior acrylic emulsion paint (Apex Ultima protek of Asian or equivalent of other specified makes) over a coat of exterior sealant and exterior primer (or) base coat as per manufacturer's instructions etc., complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in sunken floors and paving exceeding 15cm thick above ground floors not otherwise specifically provided for including removal of debris to outside MD land.etc., complete all as specified and as directed.

Material and labour for Rendering 15mm thick in Cement Mortar 1:3 mixed with water proofing compound as per manufacturers' instructions on sunken concrete floor surfaces, finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Material and labour for providing 25mm thick Plain Cement Concrete 1:2:4, type B1, using 20mm graded stone aggregate as in foundation, filling in sunken flooring portions and mass concrete etc., complete all as specified and as directed.

Material and Labour for cleaning the top surfaces of roof /floor with wire brush and washing with hydrochloric acid to remove all loose gravel, dirt, oil, grease, loose particles, foreign materials etc., by jet of dry air and clean the surface mechanically or by grinding to make it smooth and provide three layers of monolithic, seamless finish having >500% elongation water proofing treatment insitu application with liquid membrane type by using water based UV Resistant Elastomeric PU liquid membrane of ShaliUrethane® BTD or equivalent of other specified makes by applying first coat of ShaliUrethane® BTD @ 1Kg/Sqm by brush/ roller/ airless spray over a prime coat of Shaliprime BTD @ 400 Gms/Sqm, spread non woven Geo textile or Fibre glass tissue/scrimp of 45-50GSM with overlaps of 50mm on both directions when the surface of first coat is still tacky and allow it to dry for 10-12 hours and then apply a Second coat of ShaliUrethane® BTD in two layers @ 1Kg/Sqm for each layer for final DFT of 1500 micron in two coats by brush/roller/ airless spray perpendicular to the first coat for cross linkage as per the manufacturers instructions etc.,complete all as specified and as directed.

Material and labour for preparation of new wooden surface of any description exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc., complete all as specified and as directed.

Material and labour for preparation of old painted wooden surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new steel surface of any description exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description not exceeding 10cm width or girth when unconnected with other painting and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for Plain Cement Concrete 1:3:6, type C2, 75mm thick (using 40mm graded stone aggregate) laid to a slope of 1:20 as in floors, plinth protection, foot path etc., finished the surfaces even and smooth without using extra cement all as specified and directed.

Material and labour for providing 12mm wide and 50mm deep joint at a distance not exceeding 3 Metre and at corners and junction of plinth protection to vertical surfaces with mastic filling of bitumen 85/25 and the sand in the ratio 1:2 by weight all as specified and directed.

Material and labour for providing precast cement concrete, 1:2:4, type B1, using 20mm graded stone aggregate and set in CM 1:6 as in landings, manhole cover slabs, chullah hoods, Chajjas, water troughs, shelves, cooking platform and similar articles with plain faces complete all as specified and as directed. Note: Reinforcement bars shall be measured and paid separately.

Material and labour for Mild steel TMT bars of quality conforming to Fe-500D in reinforcement, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and as directed.

Material for labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 200/225mm internal dia pipes complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and as directed.

Material and labour for Hardcore of gauge not exc. 63mm using Broken stone or boulders, deposited spread and levelled in layers not exceeding 15cm thick, watered and well rammed to a true surface complete all as specified and as directed.

Material and labour for 75mm thick Plain Cement Concrete 1:4:8, type D2, using 40mm graded stone aggregate as in hard standing, finished the surfaces even and fair to receive the top layer complete all as specified and as directed.

Material and labour for laying of machine pressed precast concrete interlocking paver block, 60 mm thickness, M-35 grade with grey cement and pigments of any shape and size confirming to IS 15658-2006 over 50mm thick compacted sand cushioning complete all as specified and as directed.

Material and labour for Providing Plain Cement Concrete, 1:2:4, type B1, using 20mm graded stone aggregate as in plinth courses, copings, kerbs, bed plates, hold fast blocks, levelling courses and the like including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Material and labour for Chequered cement concrete tiles, 25mm thick of size 300x300mm, set and jointed in neat cement slurry in floors and pointed with grey cement and no pigments over and including 20mm thick screed in cement mortar 1:6 etc., complete all as specified and as directed.

Removing surplus excavated soil to a distance exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed

E/M ITEMS

Taking down carefully existing Unserviceable point wiring of any description / type / size of (light/fan/socket/call bell/two way/Power point) on TW batten/conduit complete including fittings and fixtures such as switches, ceiling roses, shades, brackets, sockets, holders, light fittings, call bells and removing the materials to store for keeping in safe custody for reuse at site or for taking credit including making good the disturbed surfaces of walls/floors/ceilings etc. complete all as specified and as directed.

Disconnecting the electric supply and dismantling of old existing un serviceable main switch / cut out/ DB's any type any capacity 240/415 Volts including old/unserviceable burnt out MCBs as per existing at site including making good the disturbed surfaces of walls/ floors/ceilings etc. complete all as specified and as directed.

Material and labour for point wiring complete with two runs of 1.5 Sqmm (for Phase and Neutral) PVC insulated unsheathed multistranded, copper conductor FRLSH cable of 1100V grade conforming to IS - 694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked of suitable dia (not less than 20mm dia) with conduit accessories concealed in wall/floor and fixed on ceiling/ roof/ truss/ columns etc, including provision of fabricated branded pressed steel terminal box of suitable sizes with 1.6mm thickness duly painted inner and outer side by anti-corrosive paint for housing the switches, sockets, fan regulator etc and covered with 3 mm thick plastic laminated sheet cover with cadmium plated screw, cup washer etc., complete concealed in walls and provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc., complete all as specified and as directed for:

One light point controlled by one one way switch.

One Ceiling fan / exhaust fan point controlled by one one way switch.

One bell point controlled by one one way bell push

One light point controlled by two Nos of 2 way switches

One 3 pin 6 Amps switch socket outlet controlled by one switch on the same board

One 3 pin 6 Amps switch socket outlet controlled by one switch on independent board

Notes for items No. 138.00 to 138.06: (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (ii) Cutting chases in brick masonry walls/concrete surfaces for concealed conduit wiring and making good the disturbed surfaces shall be measured and paid separately.

Material and labour for point wiring complete with two runs of 4.0Sqmm (for Phase and Neutral) PVC insulated unsheathed multistranded, copper conductor FRLSH cable of 1100V grade conforming to IS - 694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked, 20mm bore with conduit accessories concealed in wall/floor and fixed on ceiling/ roof/ truss/ columns etc, including provision of fabricated branded pressed steel terminal box of suitable sizes with 1.6mm thickness duly painted inner and outer side by anti-corrosive paint for housing the switches, switch socket outlets, etc and covered with 3 mm thick plastic laminated sheet cover with cadmium plated screw, cup washer etc., complete concealed in walls and provn of 4.0sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc., complete all as specified and as directed for one switch socket outlet (plug point)16Amps controlled by one switch 16 Amps on independent board complete all as specified and directed.

Notes: (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (ii) Cutting chases in brick masonry walls/concrete surfaces for concealed conduit wiring and making good the disturbed surfaces shall be measured and paid separately.

Supply and fix switch piano, flush type, single pole, one way, 6 Amps, 230 volts, ISI marked complete all as specified and as directed.

Supply and fix switch piano, flush type, single pole, two way, 6 Amps, 230 volts, ISI marked complete all as specified and as directed.

Supply and fix Bell push, piano, flush type, single pole, one way, 6 Amps, 230 volts, ISI marked complete all as specified and as directed.

Supply and fix switch socket combination, 2 in 1, multipurpose, 2/3 pin, 6 Amps, flush type complete all as specified and as directed

Supply and fix socket outlet two-in-one, 5 pin, 6Amps, 230 Volts flush type complete all as specified and as directed

Supply and fix switch socket combination, 2 in 1, multipurpose, 5 pin, 6/16 Amps, flush type complete all as specified and as directed

Supply and fix ceiling rose, surface mount type, PVC/ Polycarbonate, isolated body with face bakelite 65 x 50mm, 3 terminals complete all as specified and as directed.

Supply and fix stepped type electronic fan regulator flush type on the phenolic laminated sheet etc., complete all as specified and as directed.

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with all accessories for fixing etc., complete all as specified and as directed.

Supply and fix Call Bell, AC, ding dong type 230 Volt, single pole, complete all as specified and as directed.

Supply and fix LED Lamp15 Watts complete all as specified and as directed.

Supply, fix, test and commissioning of Wall mounted LED tube light fittings1x22 Watts, 230 Volts Decorative ultra slim aluminium LED lighting fixture with high lumen output, environmental friendly, energy efficient with all accessories, prewired all as per Cat No.LHEXBTP7IN1S022 of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling with necessary hanging/fixing arrangements and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., complete all as specified and as directed.

Supply, fix, test and commissioning of Wall mounted LED tube light fittings 10Watts (2 feet), 230 Volts Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient with all accessories, prewired all as per Cat No.LHEXACP5IN1W010 of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling with necessary hanging/fixing arrangements and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., complete all as specified and as directed.

Supply, fix, test and commissioning of 13Watts LED decorative Bulk head light fittings, designed for modern homes with PIR sensor and premium quality diffuser for glarefree light, surface mounted oval bulk head edge-lit LED luminaire all as per Cat No.LHEXCGP7IN5W013 of Havells or techno-commercially equivalent of other specified makes complete with all accessories internally prewired including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size etc., complete all as specified and as directed.

Notes for Sl. items No.151 to 153: (a) The new fittings shall bear the CA No. and Year written by Black synthetic enamel paint using stencils or by permanent marker pen and the unit quoted shall be deemed to include the cost of writing these details. (b) LM 79 & LM 80 reports to be submitted in support of the technical specifications of fitting/fixtures

Supply, fix, test and commissioning of Energy efficient Ceiling fan of 1200mm sweep, five star rating and all accessories, 230 Volts, AC. 50 Hz Single phase with copper winding all as per Cat No.Efficiencia Neo (BLDC 26 W) of Havells or techno-commercially equivalent of other specified makes, fixed to roof/ceiling with suitable clamp and down rod including provisioning of flexible copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan etc., complete all as specified and as directed .

Disconnecting the electric supply and taking down ceiling fan of 1200/1400mm sweep from any height, sealing cable end, dismantling blades and removing fan and blades and deposit to MES store etc., complete all as specified and as directed.

Material and labour for concealed sub main wiring complete with two runs of 6.0 Sqmm single core, multistranded, FRLSH PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including new non metallic rigid PVC conduit 25mm dia medium grade, ISI marked with conduit fittings and accessories, concealed on surface/recess with one run of 6.0 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly etc., complete including taking down and removing the existing sub main wiring and making good the disturbed surface to match with the existing surface etc., complete all as specified and as directed. Note: (a) Two runs of 6.0sqmm multistranded cable and one run of 6.0sqmm cable as earth continuity conductor along with one run of non metallic rigid PVC conduit 25mm dia medium grade shall be considered as one unit length. (b) Cutting chases in brick masonry walls/concrete surfaces for concealed conduit wiring and making good the disturbed surfaces shall be measured and paid separately. (c) The wiring shall be done in proper colour coding using Red, Yellow, blue for phases, black for neutral and green for earth.

Cutting chases in brick walls/concrete surfaces, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as specified and as directed.

Supply and lay in trenches / drawn through pipes or in road crossings / paths / drains / ducts / floors / along poles / equipments etc., of LT cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric power cable with stranded aluminium conductor, 1100 volts grade confirming to IS-7098 (Part-I) 1988 of size 16 Sqmm x 4 Core including connecting up using suitable size aluminium lugs testing and commissioning and taking out the unserviceable LT UG cables etc., complete all as specified and as directed. Note : Excavation earth work, sand cushioning and brick / PCC cover cable protection shall be measured and paid separately.

Supply and lay in trenches / drawn through pipes or in road crossings / paths / drains / ducts / floors / along poles / equipments etc., of LT cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric power cable with stranded aluminium conductor, 1100 volts grade confirming to IS-7098 (Part-I) 1988 of size 35 Sqmm x 3.5 Core including connecting up using suitable size aluminium lugs testing and commissioningand taking out the unserviceable LT UG cables etc., complete all as specified and as directed. Note : Excavation earth work, sand cushioning and brick / PCC cover cable protection shall be measured and paid separately.

Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for laying of pipes/pipe lines, etc., and the like not exc 10 sqm on plan and not exc 1.5m in depth and getting out in hard / dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type soil complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50 Metre and depositing where directed at a level not exceeding 1.50 Metre above the starting point complete all as specified and as directed.

Supply and lay Unreinforced precast concrete cable cover class LV, Type 1, flat with size 250mm x150 mm x 40mm with ISI mark, factory made laid in trenches for cable protection complete all as specified and as directed.

Supply, lay / spread in trenches clean dry sand for cushioning of cable to the full width of excavated trench, 8cm thick before laying cable and 15cm thick above the cable, gently punned down, stretching and testing of cable on transformer yard etc., complete all as specified and as directed. Note : Punned thickness only will be considered or payment.

Supply and lay GI tube light grade, 25mm nominal dia, ISI marked with all fittings, complete, fixed to walls, pole ceiling or laid in trenches under road crossing/floor for cable protection at road crossing / on poles etc., complete all as specified and as directed. Note:- (i) Excavation and earth work where required shall be measured separately. (ii) GI fittings such as bends, elbows, Clamps for fixing on wall, etc are included in the unit rate.

Supply and lay GI tube light grade, 50mm nominal dia, ISI marked with all fittings, complete, fixed to walls, pole ceiling or laid in trenches under road crossing/floor for cable protection at road crossing / on poles etc., complete all as specified and as directed. Note:- (i) Excavation and earth work where required shall be measured separately. (ii) GI fittings such as bends, elbows, Clamps for fixing on wall, etc are included in the unit rate.

Supply, fix, connecting and testing factory made, Line load distribution board (MCCB DB), vertical type, TPN, 4 way, 415 Volts, metal double door, , flush type made out of 1.2mm thick CRCA sheet metal, duly powder coated and conforming to IS 8623 with locking arrangements suitable to accommodate up to 100 Amps MCCBs 4 pole as incomer and 12 outgoing SP MCBs, fitted with 200 Amps rated bus bar, neutral links, blanking plate etc., all as per Cat No.DHDLVDRWGOFO04 of Havells or techno-commercially equivalent of other specified makes, concealed and fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed. Note :- (i) The unit rate quoted shall be deemed to include the cost of cutting chases into walls for concealing MCCB DB and making good the disturbed surfaces with cement work and finishing the surfaces to match with the existing surface. (ii) Incomming MCCB and Outgoing MCBs shall be measured and paid separately.

Supply, fix, connecting and testing MCCB, Four Pole, 100 Amps, breaking capacity 16kA, 415Volts, (lcs=75%lcu) with Fixed Thermal & Fixed Magnetic setting, G Frame conforming to IS: 13947-2 all as per Cat No.IHLGNF0100 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, fix, connecting and testing MCCB, Four Pole, 63 Amps, breaking capacity 16kA, 415Volts, (lcs=75%lcu) with Fixed Thermal & Fixed Magnetic setting, G Frame conforming to IS: 13947-2 all as per Cat No.IHLGNF0063 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, fix, connecting and testing factory made, distribution board, (MCB DB) SPN, 12 way, having degree of protection IP 43 with metal double door, 240 Volts, flush type made out of 1.2mm thick CRCA sheet metal, duly powder coated and conforming to IS 8623 with 200 Amps rated copper bus bar with neutral link all as per Cat No.DHDPSHODPW12 of Havells or techno-commercially equivalent of other specified makes with provision for MCB SPN as incomer and SP MCBs as outgoing complete concealed and fixed flush to wall and making good the disturbed surfaces etc., complete all as specified and as directed. Note: MCB SPN and MCB SP will be measured and paid separately.

Supply, fix, connecting and testing MCB, Single Pole Neutral (SPN), 40 Amps, 240 volts of rupturing capacity 10kA, C series type all as per Cat No.DHMGCSNF040 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, fix, connecting and testing MCB, Single Pole (SP), 40 Amps, 240 volts of rupturing capacity 10kA, C series type all as per Cat No.DHMGCSPF040 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, fix, connecting and testing MCB, Single Pole (SP), 6-32 Amps, 240 volts of rupturing capacity 10kA, 'C' series all as per Cat No.DHMGCSPF006-032 of Havells or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 230 mm sweep, 1400 / 1350 RPM or more, Air Delivery not less than 510 Cum/Hour, single phase, 240 Volts, AC, 50 Hz all as per Ventil Air - DSP of Havells or techno-commercially equivalent of other specified makes including cutting hole in to the wall / existing window / ventilator etc., and making good the disturbed surfaces and connecting up complete including provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose including taking down the old unserviceable exhaust fan etc., complete all as specified and as directed. Note :- (i) The unit rate quoted shall be deemed to include the cost of making hole in walls/other surfaces, making good the disturbed surfaces including any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan and matching to the existing surface. (ii) Old unserviceable Exhaust fans should be handed over to MES stores.

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1060 Cum/Hour, single phase, 240 Volts, AC, 50 Hz all as per Ventil Air - DS of Havells or techno-commercially equivalent of other specified makes including cutting hole in to the wall / existing window / ventilator etc., and making good the disturbed surfaces and connecting up complete including provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose including taking down the old unserviceable exhaust fan etc., complete all as specified and as directed. Note :- (i) The unit rate quoted shall be deemed to include the cost of making hole in walls/other surfaces, making good the disturbed surfaces including any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan and matching to the existing surface. (ii) Old unserviceable Exhaust fans should be handed over to MES stores.

Supply and fix Electric storage water heater (Geyser) of capacity 25 litres, BEE 5 Star rated, 2 kw, vertical type with tank made of ultra thick super cold rolled steel plates Feroglas dry powder coated, 800 glass coated heating elements (Shock proof and hard water proof) and powder coated metallic body conforming to IS:2082 all as per Cat No.Puro Turbo Dx of Havells or techno-commercially equivalent of other specified makes including drilling holes into the walls, provision of 2 Nos of 450 mm long Hot & cold PVC connections , 4 Nos of suitable size anchor bolts, nuts and washers, connecting up electrical and water supply lines, testing, commissioning and making good the disturbed surfaces etc.,complete all as specified and as directed .

Supply, fix, test and commissioning of new generation energy saving and environment friendly long life 40Watts LED security light fitting made up of cast aluminium housing with high power led as lighting source and lens embedded PC cover as diffuser having top opening seperate driver compartment with IP66 protection and impact resistance of IK0 suitable for operation on AC single phase 220-240 Volt, 50 Hz supply all as per Cat No.ENDURAPEARLNEOSL40WLED757PASYTOPC of Havells or techno-commercially equivalent of other specified makes with all accessories three run of 1.5 Sqmm copper conductor cable drawn through flexible conduit from ceiling rose to fitting etc., complete all as specified and as directed. Notes for Sl. items No.177: (a) The new fittings shall bear the CA No. and Year written by Black synthetic enamel paint using stencils or by permanent marker pen and the unit quoted shall be deemed to include the cost of writing these details. (b) LM 79 & LM 80 reports to be submitted in support of the technical specifications of fitting/fixtures

Supply, fabricate and installation of GI pipe bracket made out of light grade GI tubing of 40mm bore of length 1.20metre bent to shape by hot forgoing after filling of sand and fixed on pole (or) wall with 2 Nos of MS clamps made out 40 x 4mm Flat Iron including bolts, nuts and washers etc., complete all as specified and as directed.

Material and labour for Earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm, 6.0mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level, surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and earth plate connected to galvanized iron earth wire of 4mm dia as earthing conductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of MES Schedule (Part I) (2009) connected to earth test point/ main switch/ DB/ Panel board all as specified including testing on completion with and including 15mm bore medium grade GI protection pipe upto 7.5 meter long

for GI earth wire provision of concrete pit in PCC M15, type B-1 using 20mm graded stone aggregates with 40mm thick precast RCC (1:2:4), type B -1 cover reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre and connection to earth test and testing on completion all as specified and as directed.

Material and labour for Earth continuity conductor or main earthing lead of 4mm dia galvanised iron or steel wire including GI protection pipe light grade 15mm bore fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc.complete all as specified and as directed. Note:- (i) Earth lead and GI Protection pipe provide beyond 7.50 metre in earthing only shall be measured against this item.

saradhi construction combines

Sri Associates

SRI LAKSHMI VENKATESHWARA INFRATECH

UNITED TECHNO PROJECTS PVT LTD

C R R CONSTRUCTIONS

R. Wadhumal and Sons

M/s R.L.PAREEK