ADDN ALTN CUM SPECIAL REPAIR TO OTM ACCN UNDER GE EAST JABALPUR

Amount

Schedule 'A' Part-I (Restricted Area)

Item No. 01 :- Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Item No. 02 :- Demolition of cement concrete reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Item No. 02A :- Demolition of Cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for

Item No. 02B :- Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Item No. 03 :- Excavation in treanches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out any type of soil complete.

Item No. 04 :- diito as above item but depth 3.00 m.

Item No. 05 :- Excavation in treanches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out soft/loose soil complete.

Item No. 06 :- Excavation over areas not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and directed.

Item No. 07 :- PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and directed.

Item No. 08 :- RCC design mix M-25 using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed..

Item No. 09 :- RCC design mix M-25 using 20mm graded stone aggregate in Columns, pillars,butters wall , piers, posts and struts complete all as specified and directed..

Item No. 10 :- Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Item No. 11 :- Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and directed.

Item No. 12 :- Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 10 :- Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 13 :- Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel')

Item No. 14 :- Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long , complete all as specified and directed.

Item No. 15 :- BLANK

Item No. 16 :- S&F framed work such as drain cover grills, gratings etc with ends of bars shouldered and or reiverted or forged into spikes, framed guard bars and similar work conferming to Fe- 290-0 Gde-E-165 , complete all as specified and directed.

Item No. 17 :- M&L for painting to new steel surfaces of any description, over 10cm width or girth with two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Item No. 18 :- Demolition of cement concrete un-reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Item No. 19 :- Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface , complete all as specified and directed.

Item No. 20 :- Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering , complete all as specified and directed.

Item No. 21 :- RCC design mix M-25 using 20mm graded stone aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like , complete all as specified and directed.

Item No. 22 :- Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

Item No. 23 :- Dismantling structural steel work including doors, gates but excluding framed truss etc, complete all as specified and directed..

Item No. 24 :- M&L FLY ASH Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Item No. 25 :- M&L for rendering on fair faces of brick work or concrete surface of wall 10mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed.

Item No. 26 :- M&L Rendering 15mm thick in CM (1:4) on fair faces of concrete surfaces finished even and smooth with WPC by 3% of weight of cement used on parapet/chajja etc complete all as specified and directed.

Item No. 27 :- Supplying only Integral waterproofing compound complete all as specified and directed.

Item No. 28 :- S&F precoated steel window Rolled formed GI Section ECO 4000 (Openable double rebate window) Providing and fixing of single rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50 mm, centre mullion section 48 x 50 mm, shutter section 47 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter with a 20 mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Charge.

Item No. 29 :- S & F for solid WPC door frame of size 85x45mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed

Item No. 30 :- S & F factory made solid panel WPC door shutter 35 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed

Item No. 31 :- S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed

Item No. 32 :- S & F factory made solid panel PVC door shutter 35 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed

Item No. 33 :- S&F Butt hinges medium weight cold rolled staineles steel 100mm long complete.

Item No. 34 :- S&F Aluminium anodised barrel tower bolts of extruded section 200mm long complete,

Item No. 35 :- S&F Aluminium handles cast type anodised of 200mm complete.

Item No. 36 :- S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 complete all as specified and directed.

Item No. 37 :- S&F 1.6 mm thick Mild steel, plain, black sheet in roof cover ,wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc

Item No. 38 :- S&F 300mm long aluminium alloy anodized sliding door bolt with hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy, complete all as specified and directed by Engr-in-charge.

Item No. 39 :- Suspended false ceiling system using Chicago metallic (E - grid) exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick (Thickness comprising of GI/0.4 mm+ PPPCGS/0.3 mm & weight of runner 1.35 kg for 3600 mm length), Cross Tee of dimensions 29mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 kg for 600mm length) and Wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI / 0.35mm + PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 6 mm thick HPSC (High pressure steam cured) pre primed, self embossed, textured designer board, water resistant, termite resistant, fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed.

Item No. 40 :- Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per directions of Engineer-in-Charge.

Item No. 41 :- S&F in repair , Aluminium anodised sections for doors/windows/ventilators with one or more rebates including joining cleat and rubber packing and rollier for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- Floor door spring, sheet glass, wire cloth, lock, etc shall be measured and paid seperately.incl taking down of shutter, complete all as specified.

Item No. 42 :- BLANK

Item No. 43 :- S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm with stainless steel wire staples, complete all as specified.

Item No. 44 :- M & L aluminium grills(Decogrill) and fixed including necessary glazing clips, anodized aluminiunm snap beading screws and aluminium fittings complete all as specified and directed.

Item No. 45 :- Supply & Fixing 18 mm thick, PVC sheet one side 1mm prefemlaminated of approved texture as in Kitchen cabinet (withshelves and partitions) including necessary fitting & fixture as per manuacturer's instructions complete all as specified & directed.

Item No. 46 :- Supply & Fixing 'in repair' 18 mm thick, PVC sheet one side prelaminated of approved texture as in cupboard (withshelves and partitions) as per manuacturer's instructions complete all as specified & directed.

Item No. 47 :- S&F 40 mm dia , brass cupboard knobs fixed with nut ,screw and washer of mild steel bright complete

Item No. 48 :- M&L PCC 1:3:6 type C2 using 40mm graded stone aggregate, 100 mm thick in floor finished even and fair for bedding of tiles including necessary form work complete all as specified and directed.

Item No. 49 :- M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate, 150 mm thick in floor finished even and fair for bedding of tiles including necessary form work complete all as specified and directed.

Item No. 50 :- S&F Mortice lock,vertical type size 100 mm 4 lever as complete all as specified and directed

Item No. 51 :- M&L 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame , complete all as specified and as directed.

Item No. 52 :- M&L Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame , complete all as specified and as directed.

Item No. 53 :- M&L floor door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to aluminium door etc. complete all as specified and directed.

Item No. 54 :- BLANK

Item No. 55 :- Preparation of new plastered or un-plastered surface and applying two coat of cement base paint on walls over a coat of primer complete all as specified and directed.

Item No. 56 :- BLANK

Item No. 57 :- M&L 75 mm thick PCC 1:4:8 type D2 as in floors as sub base using extra cement in patches all as specified and directed.

Item No. 58 :- M&L 25 mm thick PCC 1:2:4 B-0 type as in floors as sub base in patches all as specified and directed.

Item No. 59 :- M&L for ENDURA out door tiles 40 cm x 40 cm x 12 mm thick rubberised mould set, jointed and pointed in neat cement slurry as in floors etc including 15 mm thick screed bed or bedding layer of cement mortar 1:6, for laying of tiles complete all as specified and directed.

Item No. 60 :- M&L Vitrified Ceramic tiles 9 - 10 mm thick (square/ rectangular) dark shade/double charged/ultra charged polished, nano tech, area of each tiles exceeding 0.18 sqm, but n exc .38sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ( in patches to match the existing colour /shed) including 15 mm thick screed bed or bedding layer of cement mortar 1:6, for laying ceramic tiles complete all as specified and directed.

Item No. 61 :- S&F Coloured Glazed ceramic tiles in vertical surfaces 350mm x250mmx 7mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in CM(1:4) on fair face of brick or concrete surface complete all as specified and directed.

Item No. 62 :- Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including making good and providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core ,etc. not exc. 50m in distance, complete all as specified and directed.

Item No. 63 :- M&L RCC type B1 (1:1.5:3) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Item No. 64 :- Taking down chowkats or frames exc 1.50 sqm but n exc 4 sqm with shutter (without taking off shutters from the frames), complete all as specified and directed.

Item No. 65 & 66 :- BLANK

Item No. 67 :- Supply, laying and jointing 150 mm nominal bore dia DWC(HDPE double wall corrugated), socketed and sewage pipes having 6.0 M length, conforming to IS 16098 (Part-2) of SN-4 Stiffiness with and including necessary jointing matrials etc complete all as specified and directed.

Item No. 68 :- M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Item No. 69 :- M&L for preparation of new steel surface of any description n exc 10cm width or girth and applying two coats of Aluminium paint ( 1st quality) over one coat of red oxide primer complete all as specified and directed.

Item No. 70 :- Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed

Item No. 71 :- Removal of excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed

Item No. 72 :- S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) incl cement concrete bedding, complete all as specified and directed.

Item No. 73 :- S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float & handle including brackets, complete all as specified and directed.

Item No. 74 :- M & L Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick in cooking platforms bedded and jointed with grey cement slurry and pointed to match the shade of granite stone including grinding and polishing types including screed bed 15 mm thick in CM 1 : 6, complete all as specified and directed.

Item No. 75 :- S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets, complete all as specified and directed.

Item No. 76 :- S&F in repair bib tap fancy type chromium plated screwed for iron pipe of 15mm bore complete all as specified and directed.

Item No. 77 :- S&F in repair Angle valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

Item No. 78 :- BLANK

Item No. 79 :- S&F in repairs CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, complete all as specified and directed.

Item No. 81 :- S&F 15mm boreGI tubes, 'medium grade' galvanised, with all fitting and fixed complete tincl cutting chaising pinning and making good to walls and ceiling or laid in floors, complete all as specified and directed.

Item No. 82 :- S&F 20mm bore GI tubes, 'medium grade' galvanised, with all fitting and fixed complete tincl cutting chaising pinning and making good to walls and ceiling or laid in floors, complete all as specified and directed.

Item No. 83 :- S&F PVC connections 15mm size with PTMT nuts of length 450mm , complete all as specified and directed.

Item No. 84 :- M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement, complete all as specified and directed.

Item No. 85 :- S&F Grating doom 100 mm dia of PTMT (min. weight 25 gms), complete all as specified and directed.

Item No. 86 :- S&F 500 Ltrs Capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I , complete all as specified and directed.

Item No. 87 :- S&F Ball valves 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 20mm-210 gms), complete all as specified and directed.

Item No. 88 :- M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Item No. 89 :- Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams etc, complete all as specified and directed.

Item No. 90 :- Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Item No. 91 :- Taking down existing loose plaster & Clean rusted reinforcement and exposed concrete surface by sandblasting .mechanical devices or any other estabilis-hed methods and follwing stage complete please (a) Application of two coats of mineral based polymer modified corrosion inhibiting primer Colusal MK +Colusal 25 (b) Application of two component polymer based bond coat Zentrifix HB+Natufill BB2 or mortar low permeability or guinting with guniting aid (C) Application Application of carbonation resistant ,polymer modified reeady to ise fine mortar ,Nafuquick +natufill BB2 or Zen-trifix F82+Nafufill BB2 Over the whole surface

Item No. 92 :- Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

Item No. 93 :- M&L PCC 1:2:4 B-I type 20 mm aggrgate Providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces,including chamfers, weatherings, throat- ing etc. and setting in mortar Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

Item No. 94 :- M & L 40 mm thick PCC 1:2:4 B-0 type as in floors as sub base in patches all as specified and directed by Engr-in-charge.

Item No. 95 :- M&L for preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of chalk whiting including clearcolle and priming with alkali resistant priming paint on plastered and other surfaces complete all as specified and directed.

Item No. 96 :- Taking down all loose particles .weak ,slurry layer , oil amd dirt layer ,if any and roughen and clean surface .Epoxy coatingsurface preparation will be done with vacuam ball blasting machine or similar surface prepartion machines.weak concrete will beremoved . eyelet voids and holes will be repaired in accordance with the technique. and follwing stage complete please (a) Surface Repair :- it there are pits ,fractures and cracks on the floor concrete surface ,segregations are the made withepoxy primer and epoxy mortar/cracks are deeper than 4-5 mm and have a large are ,cement -based repair mortars may also be preferred. (b) Mixing Ingredients : - While preparing the epoxy material, component A (epoxy resin) must first be mixed with a low speed (300-400 RPM), While the mixing process is gradually Added to component B (Epoxy hardener) and until the material becomes homogenrous at least 3 min ,mixing will continue. (c ) Epoxy Primer Application : - Solvent free Epoxy Dekapol CP 203 is ready for primer Appication .like other materials to be used in the application. Epoxy primer will be solvent -free. Epoxy primer consumption will be 400 g/m2 and 400g/m2 quartz filler will be enteredin it.after the applicatin with a trowel, sand will be sprinkled on the application with a consumption of 2.0 kg/m2, epoxy primer it penetrates into the concrete fills the voids, increases the inpact and chemical resistance of the surface. (d) Mezzanine Application ;- Solvent free epoxy primer applied surface will be protected from moisture ,dust and air flow will not be opened to pedestrain or vehicle traffic,depending on the weather and ambient temperature ,solvent -free epoxy intermediate coat will be applied on it 8-24 hours after primer application. the excess silica quartz filler we have sprinkled will be removed with the help of industrical booms epoxy intermediate coat will be applied in desired color and with a trowel.solvent free epoxy dekapol ML457 Intermidiate coat material will be applied with a consumption of 800 gr/m2 (e) Epoxy coating TOPCOAT :- After the epoxy interlayer application ,the surface will be protected form moisture ,dust and air flow, it will be not opened to pedestan or vehicle traffice in any way. depending on the weather and ambient temperature ,solvent free epoxy paint will be applied as a top coat 8-24 hour after the intermediate coat application. Solvent free Epoxy Deapot CT-455 Paint will be applied inthe desired color,with a check rust and /or roller with condumption 300 gm/m2 .when the application is finished a slightly gariny looking surface will be obtained

Item No. 97 :- S&F Rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates GDE Fe410-W(Gde- E-250) quality B complete all as specified and directed.

Item No. 98 :- S & F Decorative type pelmet rod / curtain rod 20mm dia incl finial rings ,holders complete all as specified and directed.

Item No. 99 :- S & F Bracket for Dropy Rod of decorative type of colour of PVC complete.

Item No. 100 :- S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Item No. 102 :- S&F Saftey lever locks mild steel with 4 leavers for rolling shutters complete all as specified and directed.

Item No. 103 :- Supply only MS sheet 1.25mm thick for hood cover complete complete all as specified and directed.

Item No. 104 :- Supplying only curtain ie interlocking lath sections formed from cold rolled steel strip 1.24mm thick complete all as specified and directed.

Item No. 105 :- Supply only helical wire spring or flat spiral spring complete.

Item No. 106 :- S&F Ball bearing for rolling shutters complete all as specified and directed.

Item No. 107 :- Supply only ` 40mm bore pipes heavy weight for suspension shaft complete all as specified and directed.

Item No. 108 :- Dismantling of AC corrugated/semi corrugated sheets as in roof covering complete all as specified and directed.

Item No. 109 :- Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Item No. 110 :- S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap with coach screw & washer in roof, wall etc. complete all as specified and directed.

Item No. 111 :- S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings etc.fixed with self tapping screws complete all as specified and directed.

Item No. 112 :- S&F 1.00mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashings (length & girth as fixed) with grade of zinc coating 275, complete all as specified and directed.

Item No. 113 :- S&F MS hand rails, half round or other section for wind ties for roof, brackets for valley gutter including securing bolts; , drilling holes, notching all as specified and directed. under 'Structural Steel'), complete all as specified and directed.

Item No. 114 :- Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, n exc 10cm width or girth when unconnected with other painting or when painted in different tint, including preparation of new surface & applying one coat of red oxide, zinc chrome, complete all as specified and directed.

Item No. 115 :- S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O, complete all as specified and directed.

Item No. 116 :- Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each complete all as specified and directed.

Item No. 117 :- M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:6) complete all as specified and directed.

Item No. 118 :- S&F Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top & bottom runners, brass handles etc., as specified, erected in position & securing runners with holdfasts & brackets, complete

Item No. 119 :- M&L providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement , complete all as specified and directed.

Item No. 120 :- M&L Machine cut kota stone slab flooring 20-25mm thick laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing over and including 15mm screed bed in CM 1:4 complete all as specified and directed.

Item No. 121 :- M&L Machine cut kota stone slab flooring 20-25mm thick laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing over and including 15mm thick screed in CM(1:6) complete.

Item No. 122 :- M&L Marble work 18 to 20mm thick in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types, complete all as specified

Item No. 123 :- Resecuring or easing & adjusting, without taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and derected.

Item No. 124 :- Resecuring or easing & adjusting, without taking down Shutters of any description n exc 1 sq.m each complete all as specified and derected.

Item No. 125 :- Resecuring or easing & adjusting, without taking down Shutters of any description exc 2 sq. m each complete all as specified and derected.

Item No. 126 :- S&F in repair 100 mm steel handle for steel window complete all as specified and derected.

Item No. 127 :- S&F in repair steel peg stay for steel window complete all as specified and derected.

Item No. 128 :- M&L 75 mm thick PCC 1:3:6 type C-2 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

Item No. 129 :- Applying one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old surface complete all as specified and derected.

Item No. 130 :- M&L for complete removal of existing treatment plastered surfaces of walls and applying two coat of oil bound distemper over a coat of chalk whiting including clearcolle and priming with alkali resistant priming paint on plastered and other surfaces complete all as specified and directed.

Item No. 131 :- M&L for preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of chalk whiting including clearcolle and priming with alkali resistant priming paint on plastered and other surfaces complete all as specified and directed.

Item No. 132 :- M&L for complete removal of existing treatment and applying two coats of Cement base paint over a coat of primer including preparation of surface complete all as specified and derected..

Item No. 133 :- M&L 100 mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in sub base complete all as specified and derected.

Item No. 134 :- Polythene film, black 150 micron laid in floors complete all as specified and derected.

Item No. 135 :- M&L Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less finished even and smooth complete all as specified and derected.

Item No. 136 :- Forming 12 mm thick Expansion joints filled with pre-formed bituminous filler & top 30mm primed & sealed with sealing compound, Grade `A' Thickness of concrete slab 250 mm complete all as specified and derected.

Item No. 137 :- Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'B' complete all as specified and derected.

Item No. 138 :- Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and derected.

Item No. 139 :- M&L PCC in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed type B1 (1:2:4) using 20 mm graded aggregate complete all as specified and derected.

Item No. 140 :- S&F Rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) GDE Fe 410-0 W (Gde E-250) quality A, complete all as specified and derected.

Item No. 141 :- S&F roller to slide the steel door all as specified and directed complete all as specified and derected.

Item No. 142 :- Taking down chowkats or frames not exc 1.5 Sqm each complete all as specified and directed.

Item No. 143 :- M&L for keyed pointing to brick wall in cement mortar 1:3 complete all as specified and directed.

Item No. 144 :- Turbo ventilator complete all as directed by GE. Note: size and design shall be decided by GE as site requirment.

Item No. 145 :- Taking down of eves gutter, rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

Item No. 146 :- S&F, PVC (SWR) pipes 200mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

Item No. 147 :- S&F 100 mm dia Stack clamp sout of 50 mm by 5 mm flat iron and 16 mm dia around iron stays including bolts and nuts and securing ends of stays to wall or roof making good all respect completed as directed as specified

Item No. 148 :- S&F 200 mm bore PVC (SWR) bends ISI marked any radius with access door complete all as specified and directed.

Item No. 149 :- M&L for chipping of damaged concrete of RCC member carefully and cleaning of all loose particles and providing and laying of Emaco S88 CT or equivalent fiber re-inforced pre packed Polymer Modified cementitious mortar on the sound substrata ans making the surface in original shape incl curing for 3 days for an avg thickness of 25mm all as per manufacturers instruction. Note: Any extra reinforcement etc to be added shall be incorporated as directed. Reinforcement shall be measured and paid seperatly.

Item No. 150 :- M&L of 20mm thick wearproof topping as specified for heavy duty floor (incorporating an approved metallic floor hardner), finishing even and smooth without using extra cement (except matallic hardner) over 30mm thick granolithic concrete 1:1:2 floor topping laid over cement concrete sub floor etc and finished to an even and fair surface complete all as specified and directed. Note: The wear proof floor shall be laid while the grenolithic concrete is green.

Item No. 151 :- Supply only metallic hardner of approved make complete all as specified.

Item No. 152 :- M&L fly ash brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed.

Item No. 153 :- 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate complete all as specified and directed.

Item No. 154 :- M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

Item No. 155 :- M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

Item No. 156 :- M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Item No. 157 :- M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Item No. 158 & 159:- BLANK

Item No. 160 :- M&L Mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

Item No. 161 :- S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed.

Item No. 162 :- S&F figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

Item No. 163 :- M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed

Item No. 164 :- Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed.

Item No. 165 :- S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed.

Item No. 166 :- S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Item No. 167 :- S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

Item No. 168 :- S&F Butt hinges 100mm size, medium weight, cold rolled mild steel complete all as specified and directed.

Item No. 169 :- S&F White Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in CM(1:4) complete all as specified and directed.

Item No. 170 :- S&F White Glazed earthenware tiles 300x200x7mm thick, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick screed in CM(1:4) complete all as specified and directed.

Item No. 171 :- S&F Ball brass valves 15mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Item No. 172 :- S&F CP Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Item No. 173 :- S&F Stop valves 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

Item No. 174 :- S&F Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

Item No. 175 :- S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern & flush pipe) complete all as specified and directed.

Item No. 176 :- S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, & cover & mild steel CP or aluminised hinging device complete all as specified and directed.

Item No. 177 :- S&F PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float & handle including brackets complete all as specified and directed.

Item No. 178 :- S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (min.), with grating & union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) complete all as specified and directed.

Item No. 179 :- S&F Towel rail 600mm long of PTMT fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and directed.

Item No. 180 :- S&F PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed.

Item No. 181 :- S&F Soap dish, Vitreous China white, approximate size 160x160x90mm complete all as specified and directed.

Item No. 182 :- S&F Grating doom 100 mm dia of PTMT (min. weight 25 gms) complete all as specified and directed.

Item No. 183 :- S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Item No. 184 :- S&F PVC (SWR) 'S' trap of 110mm bore complete all as specified and directed.

Item No. 185 :- S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed.

Item No. 186 :- M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete all as specified and directed.

Item No. 187 :- S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

Item No. 188 :- S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

Item No. 189 :- S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

Item No. 190 :- S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

Item No. 191 :- S&F PVC (SWR) branch pices (single Y) equal of 110 mm bore of pipe complete all as specified and directed

Item No. 192 :- Applying three coats of white wash on new wall surface including preparation of surface complete all as specified and directed.

Item No. 193 :- BLANK

Item No. 194 :- Applying three coats of white wash on new Ceiling surface including preparation of surface complete all as specified and directed..

Item No. 195 :- M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

Item No. 196 :- M&L 150mm dia Salt-glazed stoneware drain pipes laid in trenches & jointed as specfified.

Item No. 197:- BLANK

Item No. 198 :- M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished even & smooth (without using extra lime or cement) complete all as specified and directed.

Item No. 199 :- M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed. Noted : (a) curing tank should be construeted 4x4x.9 m at ridge road complain cell (b) steel from work must be used for casting (c) PCC Platefrom must be construction at ridge road comlpain cell (d) Mild steel plate surrouding each cover slab . it shoud paid separately and TMT Bar will be be paid separately.

Item No. 200 :- Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 100m or under, beyond the ead included in the rates, including loading, unloading and stacking at the destination as directed.

Item No. 201 :- Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion & making good disturbed ground embedded in Concrete, brick work, masonry, etc complete all as specified and directed.

Item No. 202 :- Dismantling fencing wire mesh, any type complete all as specified and directed.

Item No. 203 :- Removal of existing detoriated decayed tarfelt or any other treatement incl PCC padding , loose surface and removing the debris to low laying area depositing where directed complete all as specified.

Item No. 204 :- Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm complete all as specified and directed.

Item No. 205 :- Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces complete all as specified and directed.

Item No. 206 :- APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

Item No. 207 :- M&L for applying two coats of bituminous aluminium paint including preparation complete all as specified and directed.

Item No. 208 :- M&L for polymer mortar 3mm thick to fill the gap all as per manufacturersb instructions all as specified and directed.

Item No. 209 :- M&L cement concrete type A0 (1:1.5:3) using 12.5 mm graded aggregate with WPC set in CM(1:4) as in pre cast curved shell panel of roof incl removal of damage portion from the roof all as specified and directed.

Item No. 210 :- S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips & providing & fixing new ones complete all as specified and directed.

Item No. 211 :- M&L for complete removal of existing treatment and pplying two coats of white wash over a coat of primer including preparation of surface complete all as specified and directed.

Item No. 212 :- Ditto as above but as on ceiling complete all as specified and directed.

Item No. 213 :- S&F Expanded metal, cut to length, bent to shape required & tying with & including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied & fixed complete to wood or steel members Weight per square metre n exc 4Kg per Sqm complete all as specified and directed.

Item No. 214 :- Providing and laying of Emaco S88 CT or equivalent fiber re-inforced pre packed Polymer Modified cementitious mortar on the sound substrata ans making the surface in original shape incl curing for 3 days for an avg thickness of 25mm all as per manufacturers instruction complete all as specified and directed.

Item No. 215 :- S&F suspended false ceiling using Chicago metallic E-Grid exposed suspended sys , grid sec size 600 x 600mm comprising of GI powder coated main runners of dim 39 x 24 x 360 x 0.88 mm thick (thickness comprising 0.40 mm + PPP GSO 30 MM and weight of runners 1.35 kg for 3600 mm length. Gross T of demesnes of 29 x 24 x 600 x 0.80 mm thick. The thickness of comprising GI 0.040 mm + PPPC GS (0.30 mm and weight of T 0.195 kg for 6000 mm length) and wall angle of dimension 22.2 x 22.20 x 3050 x 0.65 thick (the thickness comprising of GI 0.35mm + PPGC GS 0.30 and eight of angle 0.70 kg for 3050 mm length) with and including 4 mm thick HPSC (Tugs pressure steam cured) Preprimed, self embossed texture dingier bound water termited and sesistant for including and acoustic purpose the to be placed in the grid system duly suspended with 4mm dia GI war hangers fixed with steel dash trough fasteners from purline of the roof with butterflyclips (wt 0.007 kg per clip) hold down clip wt 0.0035 kg per clip) with provision of complete all as specified. Note:-PPPCGS Densts Prep anted Polysters Coated Galvanised steel.

Item No. 216 :- Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil complete all as specified and directed.

Item No. 217 :- M&L 100 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) in floors finished complete all as specified and directed.

Item No. 218 :- Cutting out grooves in existing roofs or terracing, cleaning out, wetting, grouting with cement & sand slurry 1:3 for inserting membrane complete all as specified and directed.

Item No. 219 :- M&L 10 mm thick rendering on roof surfaces/ concrete surface in CM 1:4 complete all as specified and directed.

Item No. 220 :- M&L PCC tiles 250x250x 20mm thick laid over 15mm thick cement mortar (1:4) and jointed with polymer based tile filler compound complete (over mebrens) complete all as specified and directed.

Item No. 221 :- M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/kerbs/sunken slab etc complete all as spd and directed,

Item No. 222 :- M&L Roughing surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and applying cement slurry @3kg/sqm complete all as specified and directed.

Item No. 223:- BLANK

Item No. 224 :- Taking down steel tubing and connections incl cleaning for refixing or removal form site for 20mm bore pipe all as specified and directed by Engr-in-charge.

Item No. 225 :- Refixing 20mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

Item No. 226 :- S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Item No. 227 :- S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Item No. 228 :- Dismantling water tanks & removing to store exc 250 & n exc 500 litres complete all as specified and directed.

Item No. 229 :- Taking down steel tubing and connections incl cleaning for refixing or removal form site for 15mm bore pipe complete all as specified and directed.

Item No. 230 :- S&F 15mm bore tubes UPVC pipe with all fitting and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and directed.

Item No. 231 :- All as per srl item No- 230 above but 20mm dia complete all as specified and directed.

Item No. 232 :- M&L for anti skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38sqm, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

Item No. 233 :- S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring & pulley wheel, complete all as specified and directed.

Item No. 234 to 236:- BLANK

Item No. 237 :- S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified and directed.

Item No. 238 :- S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete all as specified and directed.

Item No. 239 :- BLANK

Item No. 240 :- S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

Item No. 241 :- BLANK

Item No. 242 :- S&F in repair of stainless steel soap dish, of standard size and shape complete all as specified and directed.

Item No. 243 :- S&F MS Peg set of six powder coated as approved complete all as specified and directed.

Item No. 244 :- S&F in repair chromium plated toilet paper holder with flap complete all as specified and directed.

Item No. 245 :- Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Item No. 246 :- M&L for double charged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed (1:6) complete all as specified and directed.

Item No. 247 :- All as per item No 246 above but on vertival surface as in skerting over and including 10mm thick rendering 1:4 in CM complete all as specified and directed.

Item No. 248 :- M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed

Item No. 249 :- M&L for preparation of old decorated surfaces of walls by complete removal of existing treatment and applying two coat of oil bound distemper over a coat of birla wall care putty complete all as specified and directed.

Item No. 250 :- M&L for preparation of old surface of ceiling and applying one coat of white wash all as specified and directed.

Item No. 251 :- Applying one coat of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and directed.

Item No. 252 :- Applying two coats of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of pink primer complete all as specified and directed.

Item No. 253 :- Providing & injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / Sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall & rodding etc.complete all as specified and directed.

Item No. 254 :- Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres / m including drilling & plugging holes etc. in apron complete all as specified and directed.

Item No. 255 :- Treatment of soil under existing floors using emulsion @ 01 litre / hole, 300mm apart including drilling & plugging 12mm dia holes with CM(1:2) to match the existing floors complete all as specified and directed.

Item No. 256 :- Taking down and removing from site shutter of any discription exe 1 sqm but nexc 2 sqm complete as specifed and directed

Item No. 257 :- BLANK

Item No. 258 :- S&F door closer hydraulically regulated designation No-2 universal type of aluminium body fixed to door frames with screws or by welding suitable for door shutters of 701-805 mm in width & wt between 36-60 kg complete all as specified and directed.

Item No. 259 :- M&L 12mm thick Particle board, medium density, flat pressed, single layer type / three layer type with BWR type adhesive,fixed with screws to timber frame work complete all as specified and directed.

Item No. 260 :- S&F Sheet glass 5.5mm thick, ordinary quality & glazing with oil putty exc 0.5 square but 0.5 sq.m in each panel complete all as specified and directed.

Item No. 261 :- S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Item No. 262 :- S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Item No. 263 :- S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each panel complete all as specified and directed.

Item No. 264 :- BLANK

Item No. 265 :- M&L fly ash brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Item No. 266 :- Dismantling ballies, hard or soft wood, any position, except in posts & struts; including taking out iron straps, bolts & nuts, etc. if any Type 3 complete all as specified and directed.

Item No. 267 :- Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any Weight per sq. m N exc 4 kg complete all as specified and directed.

Item No. 268 :- BLANK

Item No. 269 :- S&F Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,size 105x60mm complete all as specified and directed.

Item No. 270 :- S&F Plain framed, panelled shutter 35mm thick (one panel) without interlocking rail & with one panel only of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. 2nd Class HW rail & style of size as per IS: 1003 (Part I), kiln seasoned & chemically pressure treated complete all as specified and directed.

Item No. 270(a) :- S & F welded steel wire fabric and fixed complete to wood or steel members weight n.exceeding 4 Kg/ Sqm complete all as specified and directed

Item No. 270A :- Supply, laying and jointing 150 mm nominal dia DWC(HDPE double wall corrugated), socketed and sewage pipes having 6.0 M length, conforming to IS 16098 (Part-2) of SN-4 Stiffiness with and including necessary jointing matrials etc complete all as specified and directed.

Item No. 270B :- M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

Item No. 270D :- soakage well of size 1.20m dia x 1.50m effective depth including necessary excavation in any type of soil , foundation in PCC 1:3:6, honey combed brick masonary with top ring of M-25 concrete incl intersepting camber and screen chamber made of brick masonary in CM 1:4, RCC cover slab in M-25/SFRC cover , intersepting pipes of RCC/DWC complete filled with brick bat all as directed as per requirment.

Item No. 270 E :- BLANK

Item No. 270F :- M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

Item No. 270G :- M&L for cement concrete (1:2:4) using 40mm agg type B2 as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

Item No. 270H :- M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

Item No. 270 J :- BLANK

Item No. 270K :- Formwork to faces of walls, retaining walls, abutments, parapets & staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better Rough finished surfaces of concrete flat

Schedule 'A' Part-II (Un-Restrected Area)

Sewage Disposal

Item No. 01-74 :- BLANK

Item No. 75 :- Taking down chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

Item No. 76 :- S & F for solid WPC door frame of size 95x45mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed.

Item No. 77 :- S & F factory made solid panel WPC door shutter 35 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed.

Item No. 78 :- S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed.

Item No. 79 :- Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed.

Item No. 80-125 :- BLANK

Item No. 126 :- Sand filling under floors or in foundation including watering & consolidation complete all as specified and directed. Note : Punned thickness shall be measured.

Item No. 127 :- Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete with grey cement and pigment complete all as specified and directed.

Area Drainage 5(e)

Item No. 128-130 :- BLANK

Item No. 131 :- S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors as in weep hole complete all as specified and directed.

Item No. 132-135 :- BLANK

Item No. 136 :- M & L for Screed bed 15 mm thick for laying floor finish as a bedding layer in CM 1:4 complete all as specified and directed.

Item No. 137 :- M&L glossy finish rubber moulded chequered cement concrete coloured tiles 25cm x 25cm x 22 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment complete all as specified and directed.

Item No. 138 :- M&L 60 mm thick rubber moulded machine pressed precast conctete interlocking paver block With Grey Cement and pigment any shape and size confirming to IS 15658-2006 of M-35 Grade complete all as specified and directed.

Item No. 139 :- Dismantling Asbestos Cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed.

Item No. 140 :- Dismantling of single layer mangalore pattern or similar tiles in roofing complete all as specified and directed.

Item No. 141 :- Dismantling of battens for tiles, shingles etc of any size including tilting fillets exc 15 cm spaced complete all as specified and directed.

Item No. 142 :- Dismantling plain or corrugated steel sheeting, any gauge, thickness, incl nanital or similar pattern roof covering complete all as specified and directed.

Item No. 143 :- S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Item No. 144 :- S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings etc.fixed with self tapping screws complete all as specified and directed.

Item No. 145 :- S&F mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

Item No. 146 :- S & F mild steel flat iron as in wind tie for roof including securing bolts confirming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

Item No. 147 :- Dismantling timber scantling 40 Sqcm and over in section in any position unframed work complete all as specified and directed.

Item No. 148 :- Ditto as above item but in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed. .

Item No. 149 :- Dismantling of wall and ceiling boards( fibre pulp insulation etc) any thickness including cover fillets complete all as specified and directed.

Item No. 150 :- M&L suspended false ceiling system using Chicago metallic (E-grid) exposed suspended system, grid size 600x600mm compressing of GI powder coated main runner of dimension 39mmx24mm x 0.8mm thick (Thickness comprising of GI/0.5mm+PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length), cross Tee of dimension 29mm x 24mm x 0.7mm thick (Thickness comprising of GI/0.5mm+PPPCGS/0.3mm & weight of Tee 0.195Kg for 600mm length) and wall angle of dimension 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI/0.35mm + PPPCGS/0.30mm & weight of angle 0.700 Kg for 3050mm length) with and including 6mm thick HSPC (High Pressure Steam Cured) pre-primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 Kg/clip), hold down clips (wt - 0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions complete all as specified and directed.

Item No. 151 :- Demolition of brick masonry built in cement mortar complete all as specified and directed.

Item No. 152 :- M & L fly ash brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cm (1:6) complete all as specified and directed.

Item No. 153 :- M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid over and including 20 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, rounding to edges and mirror polishing complete all as specified and directed.

Item No. 154 :- Ditto as per item N 153 above but as in riser of steps, skirting, dado and pillars laid over and including 10 mm thick plaster in CM 1:4 complete all as specified and directed.

Item No. 155 :- Demolition of concrete in ground floors and pavings n.exc 15cm thick below or above ground level and removing the rubbish to a distance n.exc 50m from the starting point & depositing where directed complete all as specified. complete all as specified and directed.

Item No. 156 :- M&L Non - skid coloured/designer Ceramic tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors laid over & including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Item No. 157 :- ditto- all as per item No 156 above but in skirting laid over and including 10 mm thick plaster in CM 1:4 complete all as specified and directed.

Item No. 158 :- M&L Non - skid coloured/designer Ceramic tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors laid over & including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of floor complete all as specified and directed.

Item No. 159 :- M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. laid over & including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of floor complete all as specified and directed.

Item No. 160 :- ditto- all as per item 159 above but in skirting laid over and including 10 mm thick plaster in CM 1:4 complete all as specified and directed.

Item No. 161 :-M&L for glazed ceramic colour/designer tiles 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surface such as skirting/dados laid over & including 10 mm thick plaster in CM 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

Item No. 162 :- Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed.

Item No. 163 :- M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

Item No. 164 :- Rendering 15mm thick in two layers on fair faces of brick work or concrete surfaces 10mm in CM 1:6 and 5 mm top layer in CM 1:4 mixed with integral water proofing compound finished as sand plaster complete all as specified and directed.

Item No. 165 :- M&L prepraring newly plastered surfaces of wall and applying two coat of exterior emulsion over a coat of primer after preparation of surfaces at any height including necessary scafolding etc complete all as specified and as directed.

Item No. 166 :- M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar (1:4) finished even and smooth w/o using extra cement complete and using WPC by 3% of weight of cement complete all as specified and directed. Note : WPC will be measured seprately.

Item No. 167 :- Supply only Integral water proofing compound complete all as specified and directed.

Item No. 168 :- M&L for applying two coat of distemper oil emulsion over a coat of alkali resistant cement based primer over 2mm thick birla white wall care putty on wall surfaces & smoothening the surfaces with sand papers etc., including complete removal of existing treatment of any description (such as OBD/ plastic emulsion/ interior/ exterior emulsion paint etc) before applying OBD on new/old surafaces all as specified and directed.

Item No. 169 :- M & L preparation new plastered surfaces and walls including cornices, pilasters etc and applying two coats of cement base paint over a coat of white cement primer complete all as specified and as directed.

Item No. 170 :- BLANK

Item No. 171 :- Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

Item No. 172 :- S&F 2nd class teak HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Item No. 173 & 174 :- BLANK

Item No. 175 :- S&F steel windows with side hung shutters of glazed or fly proofing including Box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed

Item No. 176 :- S&F steel windows with side hung shutters of glazed or fly proofing including Box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed

Item No. 177 :- S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

Item No. 178 :- S&F frame work such as grills, grating etc with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders etc and similar works conforming to Fe-410-0 complete all as specified and directed.

Item No. 179 :- M&L preparation of new steel surfaces over 10 cm width or girth applying one coat of red oxide and two coat of synthetic enamel paint complete all as specified and directed.

Item No. 180 :- S&F 2nd class hard wood 40 mm thick Plain, framed, panelled shutters of factory made (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed

Item No. 181 :- S&F 35mm thick second class hardwood factory made flush shutters, solid, core construction with black board core and plywood face panals commercial type on both sides including decorative laminate 0.9mm thick type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive complete all as specified and directed.

Item No. 182 :- S&F 2nd class hard wood 35mm thick glazed and skelton shutters ( factory made)of open rebated and prepared to recive glass, guaze etc (without sash bar)edges of framing plain chamfered or rouunded fitted with cut and beads for sccuring glass, gauge etc size of shutters as specified in SSR Part-I section & clause 8.20(a), complete all as specified and directed

Item No. 183 :- S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Item No. 184 :- S&F powder coated anodised aluminium door shutters aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed

Item No. 186 :- S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete complete all as specified and directed.

Item No. 187 :- S&F brass mortice lock (4 levers), vertical type, size 100mm long complete all as specified and directed.

Item No 188 : S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

Item No. 189 :- S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.50 sqm in each pane complete all as specified and directed.

Item No. 190 :- -ditto- all as item 189 above but frosted complete all as specified and directed.

Item No 191 : Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Item No. 192 :- S&F 100 mm long stainless steel but hings medium weight complete all as specified and directed.

Item No. 193 :- S & F 150 mm long extroded aluminium alloy handles, fabricated type anodized complete all as specified.

Item No. 194 :- S & F 100mm aluminium handles, cast type, anodised complete all as specified and as directed.

Item No. 195 :- S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Item No. 196 :- S & F 100mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Item No. 197 :- S & F 300 mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Item No. 198 :- S & F 300 mm long brass ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed

Item No. 199 :- M & L for PCC 1:2:4 type B1 using 20 mm graded aggregate as in bed block/hold fast blocks, padding, chajjas repair, benching and coping etc with & including necessary form work for fair faces of concrete, complete all as specified and directed

Item No. 200 :- M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate laid in panels incl joints filled with sealing compound grade 'A' as in plinth protection or path etc finished even and smooth with using extra cement complete all as specified & directed.

Item No. 201 :- M&L hard core of gauge not exc 63 mm deposited spread and lavelled in layers n-exc 25 cm watered & rammed to a true surface with broken bricks complete all as specified.

Item No. 202 :- M & L 25 mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in floor finished even and smooth with using extra cement complete all as specified and directed.

Item No. 203 :- M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including jointing with solvent, grinding, rounding to edges and polishing complete.

Item No. 204 :- Dismantling existing water storage tanks exc and n exc. 1000 liters capacity & removing from site complete all as specified and directed.

Item No. 205 :- S&F rotational moulded polyethylene water storage tanks of 1000 ltr capacity double layers (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Item No. 206 :- S&F 20mm bore ball brass valve, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Item No. 207 :- S&F 20 mm bore gun metal gate valve cast copper alloy, screwed down high pressure with wheel head, screwed both ends with crutch or butterfly handle for iron pipes complete all as specified and directed.

Item No. 208 :- Taking up or down 15 mm bore steel water tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Item No. 209 :- Ditto but 20 mm complete all as specified and directed

Item No. 210 :- S&F 15 mm bore galvanized steel tubing, medium grade galvanised with all fittings, fixed to walls and ceilings or laid in floors incl cutting chasing and making good complete all as specified and directed.

Item No. 211 :- S&F 20 mm bore galvanized steel tubing, medium grade galvanised with all fittings, fixed to walls and ceilings or laid in floors complete all as specified and directed.

Item No. 212 :- S&F 15 mm bore gun metal gate valve cast copper alloy, screwed down high pressure with wheel head, screwed both ends with crutch or butterfly handle for iron pipes complete all as specified and directed.

Item No. 213 :- BLANK

Item No. 214 :- Demolition and breaking up drain pipes of 110 mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Item No. 215 :- S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps complete all as specified and directed.

Item No. 216 :- S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Item No. 217 :- S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

Item No. 218 :- S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

Item No. 219 :- S&F PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Item No. 220 :- S&F PVC (SWR) floor trap 100 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Item No. 221 :- S&F in repairs cromium plated Soap dish complete all as specified and directed.

Item No. 222 :- S&F in repairs Vitreous China Wash hand basin, white, oval shape, size 550 mm x 420 mm size counter top, excluding taps, chain & plug & porcelain stopper incl brackets, 40/32 mm dia PVC waste pipe, chromium plate coupling 32 mm dia, pedestal & cutting for and pinning ends of brackets or erecting stand complete all as specified and directed.

Item No. 223 :- S&F in repairs CP bib taps, 15 mm dia, cast copper alloy chromium plated fancy type long body, Long Nose with Wall Flange with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Item No. 224 :- S & F in repair 15mm dia Stop/angle valves, cast copper alloy chromium plated fancy type , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Item No. 226 :- S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 50cm long brackets complete all as specified and directed.

Item No. 227 :- S&F Viterous china wash down water closet (pedestal pattern) with white seat cover including fixing bolts and CP jet system excluding flushing cistern and flush pipe but incl S or P trap complete all as specified and directed.

Item No. 228 :- S&F in repair PVC valve less, syphonic action type flushing cistern 10 liters capacity, low level white with inlet ball valve, float and handle including brackets flush pipe etc and fixed complete all as specified and directed.

Item No. 229 :- S&F 15 mm dia brass CP fancy wall mixer with L Bend for mixing hot & cold water screwed down for iron pipe and fixed as in repairs.

Item No. 230 :- S&F in repairs 15 mm dia brass CP fancy Central Hole Basin Mixer with Popup Waste System with 450mm Long Braided Hoses for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Item No. 231 :- S&F in repairs brass chromium plated overhead shower with arm and flange complete all as specified and directed.

Item No. 232 :- S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

Item No. 233 :- S&F stainess steel, Harrison rails chromium plated with fixing brackets, rings stops, rollers fancy side holders etc.(outer dia min 24mm, section thickness min 1mm) complete all as specified and directed.

Item No. 234 :- M&L one coat of synthetic enamel paint over old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

Item No. 235 :- M&L two coats of synthetic enamel painting over a coat of pink primer including preparation of new wooden surface over 10cm width or girth complete all as specified and directed.

Item No. 236 :- M&L one coat of synthetic enamel painting on steel surfaces including preparation of surface over 10cm width or girth complete all as specified and directed.

Item No. 237 :- M&L two coats of synthetic enamel painting over one coat of red oxide on steel and iron surfaces incl necessary preparation of surfaces complete all as specified and directed

Item No. 238 :- S&F Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles with 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, Light Reflectance ≥85%, Colour black, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 66% GW & 74% RW. The tile shall be laid on suprafine 32 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32mm and a load carrying capacity of 7.5Kgs/M2 with a minimum pull out strength of 100 kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system and necessary angle of make Armstrong or equivalent as approved by Engr-in-Charge complete all as specified and directed.

Item No. 239 :- Providing and Fixing Channeled Wood works perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a high density fibre board with minimum 725 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips and necessary aluminium frame work of make Armstrong or equivalent as approved Engr-in-Charge complete all as specified and directed.

Item No. 240 :- Providing and supplying ‘Optra Acoustical Wall Paneling’ with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class A as per ASTM E-84, fabric with an option of colors – Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut & Shell as per the choice of the Architect of size 600X600 mm providing a minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel impalers and necessary aluminium frame work supplied by M/s Armstrong Industries India Pvt. Ltd and construction adhesives as per the instructions laid down by the manufacturer of make Armstrong or equivalent as approved by Engr-in-Charge complete all as specified and directed.

Item No. 241 :- M&L for aluminium anodised frame for doors, windows ventilators/partions or frame work as in panelling, with one or more rebeats including jointing cleat for fixing etc complete all as specified and directed

Item No. 242 :- S&F 25 mm wide and 5 mm thick second class hard filleting including provision of two coats of varnish complete all as specified and directed.

Item No. 243 :- S&F 50 mm wide and 5 mm thick second class hard filleting including provision of two coats of varnish complete all as specified and directed.

Item No. 244 :- Taking down shutter of size exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Item No. 245 :- BLANK

Item No. 246 :- S&F 100 mm butt hinges, brass,with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

Item No. 247 :- S&F 150 mm long brass handle, cate type, polished bright and fixed complete all as specified and directed.

Item No. 248 :- S&F 150 mm long brass barrel tower bolts, with barrel of extruded section and fixed complete all as specified and directed.

Item No. 249 :- S&F 300 mm long brass, sliding door bolt withsand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

Item No. 250 :- S&F collapsible steel gates, top hung, consisting of channel pickets, pivot flat bars, top and bottom runners, brass handles etc as specified erected in position and securing with holdfasts and brackets complete all as specified and directed.

Item No. 251 :- M&L for Machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Item No. 252 :- S&F Vitrified Ceramic tiles double charged 8 to 9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Item No. 253 :- S&F Vitrified Ceramic tiles double charged 8 to 9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, as in skirtings/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed.

Item No. 254 :- M&L granite (of any type) 18 to 20 mm thick as in floor bedded and jointed in cement slurry over and including 15mm screed in CM 1:4 and pointed in cement with pigment to match the shade of granite complete all as specified and directed.

Item No. 255 :- M&L granite (of any type) 18 to 20mm thick as in risers of step bedded and jointed in cement slurry over 10mm screed in CM 1:3 and pointed in cement with pigment to match the shade of granite complete all as specified and directed.

Item No. 256 :- S&F Non - skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:3 complete all as specified and directed

Item No. 257 :- Cutting chases, pinning in stone/concrete block or slab walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Item No. 258 :- S&F in repairs wash hand basin, Vitreous China oval shaped, first quality, white colour, of size 630mm x 450mm x 175mm, including cutting for and pinning in ends of brackets or erecting stand, with and including CI brackets, PVC flexible pipe with both side brass nuts to joint and 750mm long PVC waste pipe 32mm dia, CP waste coupling with long screwed shanks and fly nuts complete all as specified and directed.

Item No. 259 :- S&F in repairs vitreous china water closet squatting pan 'orissa pattern, ivory coloured of size 580 x 440 mm, with integral foot rest and outlet for 'P' or 'S' trap , WC pan shall be set in lean concrete below level of rim of pan to receive the floor finish complete all as specified and directed.

Item No. 260:- S&F fancy type pillar taps cast copper alloy fancy type of 15 mm bore with or without 'hot or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

Item No. 261 :- S&F for brass chromium plated, 15 mm bore healthfoucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and as directed.

Item No. 262 :- S&F in repairs Vitreous China Urinal, Half stall type, white excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Item No. 263 :- S&F in repairs chromium plated urinal spreader for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

Item No. 264 :- S&F chromium plated push cock, CP Fancy type 15mm bore complete all as specified and directed.

Item No. 265 :- S&F in repairs angle stop cock chromium plated screwed for iron pipe or brass ferrule, 15 mm bore and fixed complete all as specified and directed.

Item No. 266 :- S&F in repairs brass chromium plated bottle trap for wash basin/sink with inlet and outlet screwed for pipe or connections including necessary packing, union and cap bore of trap 32mm fixed complete all as specified and directed.

Item No. 267 :- Salt glazed stone ware gully trap 150mm square type 'P' includng MS gratings suitable to 150 x 150 mm gully trap and including PCC chamber 10 cm thick and RCC cover set in CM 1:6 complete all as specified and as directed.

Item No. 268 :- M&L for rendering 5 mm thick, in cm 1:3 on fair faces of brick or concrete surfaces of ceiling and making surfaces even and smooth with out using extra cement complete all as specified and directed.

Item No. 269 :- Demolition of cement concrete in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed.

Item No. 270 :- M&L for 40mm thick PCC 1:2:4 type B0 (12.5mm) as in levelling course to match the undulations of roof and in covering etc complete all as specified and directed.

Item No. 271 :- M&L 10 mm thick cement screed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab and vertical surface ,finished even and smooth by using steel trowel complete all as specified and directed.

Item No. 272 :- M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by forced complete all as specified and directed. Four course roof treatment consists of as under :- (a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm. (b) Laying of APP based membrane as specified thickness and weight. (c) Applying one coat of bitumin grade 85/25 @ 1.2 Kg/Sqm. (d) Applying two coat of aluminium paint @ 100ml/sqm

Item No. 273 :- Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Item No. 274 :- S&F 110 mm PVC (SWR) junction single (T single) equal or unequal with acess door complete all as specified and directed.

Item No. 275 :- M&L modular size bricks with fly ash bricks straight or curved on plan exc. 6m mean radius and setting in cement mortar 1:6 etc. complete all as specified as directed.

Item No. 276 :- Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed.

Item No. 277 :- S&F powder coated aluminium frame for doors, windows with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Item No. 278 :- S&F powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Item No. 279 to 282 :- BLANK

Item No. 283 :- Venetian blinds with design on inner face, verticle type made of fiber cloth fixed to wall with necessary aluminium brackets, screws etc including Alluminium frame ropes, rollers etc as approved by GE and all as specified and directed.

Item No. 284 :- Preparing new surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Item No. 285 :- BLANK

Item No. 286 :- Complete removal of existing treatment on ceiling and applying three coat of white wash complete all as specified and directed.

Item No. 287 :- BLANK

Item No. 288 :- M&L for complete removal of existing treatment on wall and applying two coat of exterior emulsion over a coat of primer after preparation of surfaces at any height including necessary scafolding etc complete all as specified and as directed.

Item No. 289 :- M&L for anti-termite treatment of soil under existing floors using emulsion @ one ltr per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Item No. 290 :- M&L providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Item No. 291 :- M&L for anti-termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 ltrs per linear mtr including drilling and plugging holes etc in apron complete all as specified and directed.

Item No. 292 :- BLANK

Item No. 293 :- Stainless steel Gde- 308 material for staircase railing/ verandah of ht 0.985 mtr with top rail 50mm dia (16 gauge) vertical pipe 40mm (16 gauge) two longitudinal parallel pipe of size 20mm (16 gauge) with necessary connected socket, coupling brackets, bend, fittings in RCC/PCC/Wooden flooring necessary fastener complete all as specified and directed.

Item No. 294 :- S&F in repairs 18 mm thick Solid PVC Sandwich Panel with 1 mm plain colour PVC Sheet on both sides suitably fixed in M.S. angle frame work as per specification & drawing. Note : MS work shall be measured and paid separately.

Item No. 295 :- S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

Item No. 296 :- S&F 75 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

Item No. 297 :- Labour only for rounding to edges of treads and other similar situations complete all as specified and directed.

Item No. 298 :- Demolition of Cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Item No. 299 & 300 :- BLANK

Item No. 301 :- Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified and directed.

Item No. 302 & 303 :- BLANK

Item No. 304 :- M&L PCC in foundations, filling and mass-concrete type B2 (1:2:4) using 40 mm graded stone aggregate complete all as specified and directed.

Item No. 305 :- M&L RCC M-25 design mix using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Item No. 306 :- M&L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

Item No. 307 :- M&L RCC M-25 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Item No. 308 :- M&L RCC M-25 design mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Item No. 309 :- Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat complete all as specified and directed.

Item No. 310 :- Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed.

Item No. 311 :- Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed.

Item No. 312 :- Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200m thick (Horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and directed.

Item No. 313 :- M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

Item No. 314 :- M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

Item No. 315 :- S&F Rolled mild steel Roof trusses (framed), trussed purlins crane gantries, rails & fastenings & heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. GDE Fe410-0 or Fe 310-O complete all as specified and directed.

Item No. 316 :- S&F MS hand rails, half round or other section for wind ties for roof, brackets for valley gutter including securing bolts, drilling holes, notching complete all as specified and directed.

Item No. 317 :- S&F Rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates GDE Fe410-0 or Fe 310-O complete all as specified and directed.

Item No. 318 :- Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, n exc 10cm width or girth when unconnected with other painting or when painted in different tint, including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

Item No. 319 :- Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Item No. 320 :- M&L for ENDURA out door tiles 60 cm x 60 cm x 10 mm thick rubberised mould set, jointed and pointed in neat cement slurry as in floors etc . & Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying ceramic tiles/granite floor finishes complete all as specified and directed.

Item No. 321 :- All as per item No. 320 above but on vertival surface over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Item No. 322 :- S & F welded steel wire fabric and fixed complete to wood or steel members weight n.exceeding 4 Kg/ Sqm complete all as specified and directed

Item No. 323 :- BLANK

Item No. 324 :- Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

Item No. 325 :- BLANK

Item No. 326 :- M&L for preparation of new wall surface and applying two coats of emulsion over a coat of primer over 2 mm putty including preparation of surface complete all as specified and directed.

Item No. 327 :- S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O complete all as specified and directed.

Item No. 328 :- S&F Butt hinges 125mm size, medium weight, cold rolled mild steel complete all as specified and directed.

Item No. 329 :- Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions.

Item No. 330 :- S&F door closer hydraulically regulated designation No-2 universal type of aluminium body fixed to door frames with screws or by welding suitable for door shutters of 701-805 mm in width & wt between 36-60 kg complete all as specified and directed.

Item No. 331 :-M&L 12mm thick Particle board, medium density, flat pressed, single layer type / three layer type with BWR type adhesive,fixed with screws to timber frame work complete all as specified and directed.

Item No. 332 :- Demolition of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid bedded and pointed in CM complete all as specified and directed.

Item No. 333 :- M&L 100mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate complete all as specified and directed.

Item No. 334 :- M&L French polishing on surfaces of any description, width or girth including cleaning & preparing the surface including a coat of wood filler on old works with one or more coats complete all as specified and directed.

Item No. 335 :- Dismantling Wall & ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Item No. 336 :- S&F suspended false ceiling using Chicago metallic E-Grid exposed suspended sys , grid sec size 600 x 600mm comprising of GI powder coated main runners of dim 39 x 24 x 360 x 0.88 mm thick (thickness comprising 0.40 mm + PPP GSO 30 MM and weight of runners 1.35 kg for 3600 mm length. Gross T of demesnes of 29 x 24 x 600 x 0.80 mm thick. The thickness of comprising GI 0.040 mm + PPPC GS (0.30 mm and weight of T 0.195 kg for 6000 mm length) and wall angle of dimension 22.2 x 22.20 x 3050 x 0.65 thick (the thickness comprising of GI 0.35mm + PPGC GS 0.30 and eight of angle 0.70 kg for 3050 mm length) with and including 4 mm thick HPSC (Tugs pressure steam cured) Preprimed, self embossed texture dingier bound water termited and sesistant for including and acoustic purpose the to be placed in the grid system duly suspended with 4mm dia GI war hangers fixed with steel dash trough fasteners from purline of the roof with butterflyclips (wt 0.007 kg per clip) hold down clip wt 0.0035 kg per clip) with provision of complete all as specified. Note:-PPPCGS Densts Prep anted Polysters Coated Galvanised steel.

Item No. 337 to 343 :- BLANK

Item No. 344 :- M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38sqm, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

Item No. 345 to 350 :- BLANK

Item No. 351 :- S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

Item No. 352 :- S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Item No. 353 :- S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified and directed.

Item No. 354 :- S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete all as specified and directed.

Item No. 355 :- S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

Item No. 355 :- S&F cabinet mirror, box type of size 19" x 21" of colour as approved fixed to wall complete all as specified and as directed.

Item No. 356 :- S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed.

Item No. 357 :- S&F in repair of stainless steel soap dish, of standard size and shape complete all as specified and as directed.

Item No. 358 :- S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed.

Item No. 359 :- S&F in repair plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC complete all as specified and directed.

Item No. 360 :- S&F in repair chromium plated single lever wall mixer 3-in-1 system with provision of both hand shower complete with 115mm long bend pipe, connecting legs and wall flange complete all as specified and directed.

Item No. 361 :- S&F Grating doom 100 mm dia of PTMT (min. weight 25 gms), complete all as specified and directed.

Item No. 362 :- M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

Item No. 363 :- S&F aluminium composite pannel cladding with open grooves for linear as well as curvlinear portions of the Bldg/wall for all hts and all levels etc incl (a) Providing fabricating and supplying and fixing panels of aluminium composite panel cladind in pan shape in metalic colour or as approved shades out of 2mm thick aluminium composite panel with core sandwitched between two al sheets(each 0.25mm thick). The al composite panel cladding sheet shall be oil coated with Kynar 500 based PVDF/Lumiflon based fluoropolymer resine coating of approved colour and shade on face No 1 and polymer (service) coating on face no 2as specified using ss screw nuts bolts, washerscleats, weather silicon sealent backer rods etc. (b) The fastening brackets of Al alloy 6005 T5/ MS with hot clip galvanised with serrations and serrated washers to arrest the wind load movement fasteners SS 316 pin and anchor bolt of approved make in SS 316 Nylon separators to prevent bi-metalic contacts all complete required to perform as per specification of manufacturer complete all as specified and directed.

Item No. 364 to 366 :- BLANK

Item No. 367 :- Refixing 15mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and directed.

Item No. 368 :- All as per srl item No- 367 above but 20mm dia complete all as specified and directed.

Item No. 369 :- Dismantling water tanks & removing to store exc 250 & n exc 500 litres complete all as specified and directed.

Item No. 370 :- S&F 500 Ltrs Capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I.

Item No. 371 :- S&F Ball brass valves 15mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Item No. 372 :- S&F MS Peg set of six powder coated as approved by GE

Item No. 373 :- S&F in repair chromium plated toilet paper holder with flap complete all as specified and directed.

Item No. 374 :- BLANK

Item No. 375 :- M&L for applying two coat of distemper oil emulsion over a coat of alkali resistant cement based primer over 2mm thick birla white wall care putty on ceiling surfaces & smoothening the surfaces with sand papers etc., including complete removal of existing treatment of any description (such as OBD/ plastic emulsion/ interior/ exterior emulsion paint etc) before applying OBD on new/old surafaces all as specified and directed.

Item No. 376 :- M&L for rendering on fair faces of brick work or concrete surface of wall 10mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed

Item No. 377 :- M&L for rendering on ceiling 5mm thick in CM 1:3 and to be finished even and smooth without using extra cement complete all as specified and directed

Item No. 378 :- M&L for preparation of new decorated surfaces of walls and applying two coat of oil bound distemper over a coat of birla wall care putty complete all as specified and directed.

Item No. 379 :- Ditto as above but as on ceiling.

Item No. 380 :- BLANK

Item No. 381 :- M&L for complete removal of existing treatment and applying two coats of Cement base paint over a coat of primer including preparation of surface complete all as specified and directed.

Item No. 382 :- Supply and fix aluminum composite sheet cladding using 4 mm thick sheet of approved make consisting of a core of 3mm natural polyethylene core sandwitched between two skins (0.5mm each) of aluminum alloy with outer surface in all colour coating of PVDF paint in fully automatic coil coating process. The PVDF coated finished surface to factory protected with self-adhesive peel offoil tested to withstand at least 6 months exposure to local weathering conditions. The composite sheet cut and bend to shape profiles as required to, including perimeter extrusions base frame, extruded stiffeners, expansion fasteners & silicone sealant (Dow corning 789) required for installation as per approved elevation drawing as directed including necessary accessories complete in all respects. The rates shall be including the cost of all materials, tools, tackles, manpower, fuel, consumables, lead and lifts at all levels, design, fabrication, erection, finishing and dismantling of scaffolding and testing of water tightness, etc. as per manufacturerer's instructions / specifications complete all as specified and directed.

Internal Electrification

Item No. 383 :- Taking down carefully copper/aluminium unserviceable point wiring( light, fan, socket or power ) complete , including fixture and fittings such as switches, sockets, ceiling roses, pendants holder, regulators, sockets light fittings etc removing materials to stores for keeing in safe custody or for taking credit (Credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Item No. 383 :- M&L for point wiring with1.5 sqmm FR LSH size single core multi stranded copper conductor unsheathed PVC insulated 1100V grade cable drawn into and including Instove enamelled steel conduit of suitable dia sleeves and caps of adequate width and length with accessories and fittings like bend, elbows, crosses wall crossing etc for one light/fan point controlled by one switch and with continuous earth wire green colour as one number cable 1.5 sq mm copper conductor PVC insulated, unsheathed connected to earth dolly and to be connected to MS box of 1.6 mm thick having 4 Nos nuts welded to 4 corners and one no bolt welded to MS box for earth wire connection, with 3 mm thick laminated/hylem sheet cover for housing switches, sockets outlet and regulators etc. complete complete all as specified and as directed. Note :- (i) Ceiling lights/Air circulation fan pt wiring cable length approx 20 mtrs is deemed to be included in unit rate.

Item No. 384 :- All as per Item No 383 but here-in-before One Air circulation fan point controlled by one, one way switch 5 Amps

Item No. 385 :- All as per Item No 383 but here-in-before One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.complete all as specified & directed.

Item No. 386 :- All as per item No 383 here in before but 2.5 Sqmm copper conductor for 5 Pin 15 Amp switch socket combintion on independent board and 2.5 Sqmm stranded copper conductor as an earth continuous wire complete all as specified and directed.

Item No. 387 :- All as per item No 383 here in before but 4.00 Sqmm copper conductor for 5 Pin 15 Amp switch socket combintion on independent board and 4.00 Sqmm stranded copper conductor as an earth continuous wire complete all as specified and directed.

Item No. 388 :- M & L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty pvc concealed conduit of white/ivory colour including all accessories after chasing in wall/ceilling etc, heavy duty ISI marked with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly, covered with modular white cover palte with inner frame suitable for modular swithes, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point controlled by one, one way switch 5 Amps and regulator

(c) One Exaust fan point controlled by one, one way switch 5 Amps

(d) One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on indelpendednt board.

(f) One bell point controlled by one, one bell switch 5 Amps.

(g) One light point controlled by two 2 way switches with cable 1.5 sqmm size

Item No. 389 :- Description all as per item No 388 here in before but using 2.5 Sqmm single core copper conductor cable of multistranded FRLSH, PVC insulated unsheathed 1100 volts grade for 5/15 amps witch socket combination point including necessary running of 2.5 Sqmm copper conductor FRLSH, PVC wire as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed.

Item No. 390 :- Description all as per item No 388 here in before but using 4 Sqmm single core copper conductor cable of multistranded FRLSH, PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including necessary running of 4 Sqmm copper conductor FRLSH, PVC witre as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed.

Item No. 391 :- M&L for concealed point wiring complete with 1.5 Sqmm FRLSH PVC insulated and unsheathed single core multistranded copper conductor cable for working voltage 1100 volts, grade drawn into and including 20 mm dia PVC conduit of medium grade for one light /fan point controlled by one switch including 1.5 Sqmm FRLSH PVC insulated stranded copper conductor cable for earth continuity conductor and connecting to earth dolly & to be terminated in & inclusive of MS sunken box 1.2mm thick (flush metal box) for mounting of fittings like switch, socket , fan regulator etc complete with 3mm thick laminated switch board cover all as specified and as directed.

Item No. 392 :- All as per Item No 391 but here-in-before One fan point controlled by one, one way switch 5 Amps and regulator complete all as specified and directed.

Item No. 393 :- All as per Item No 391 but here-in-before One Exaust fan point controlled by one, one way switch 5 Amps complete all as specified and directed.

Item No. 394 :- All as per item No 391 here in before but One bell point controlled by one, one bell switch 5 Amps.

Item No. 395 :- All as per item No 391 here in before but One light point controlled by two 2 way switches with cable 1.5 sqmm size

Item No. 396 :- All as per Item No 391 but here-in-before One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

Item No. 397 :- All as per Item No 391 but here-in-before One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.complete all as specified & directed.

Item No. 398 :- All as per item No 391 here in before but 2.5 Sqmm copper conductor for 5 Pin 15 Amp switch socket combintion on independent board and 2.5 Sqmm stranded copper conductor as an earth continuous wire complete all as specified and directed.

Item No. 399 :- All as per item No 391 here in before but 4.00 Sqmm copper conductor for 5 Pin 15 Amp switch socket combintion on independent board and 4.00 Sqmm stranded copper conductor as an earth continuous wire complete all as specified and directed.

Item No. 400 :- S&F for modular Switch piano flush type, single pole, one way and 5/6 Amp, single modular complete all as specified and directed

Item No. 401 :- S&F for modular Switch piano flush type, single pole, one way and 15/16 Amp, single modular complete all as specified and directed

Item No. 402 :- S & F for Bell push modular 6 Amps single module complete all as specified and directed.

Item No. 403 :- S & F for modular switch 2 way 6 Amps single module complete all as specified and directed.

Item No. 404 :- S & F modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amps and 2 pin, 5/6 Amp, 2 module piano flush type complete complete all as specified and directed

Item No. 405 :- S & F modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amps and 3 pin, 5/6 Amp, 2 module piano flush type complete complete all as specified and directed

Item No. 406 :- S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed.

Item No. 407 :- S&F Modular TV Co-axial socket complete all as specified and as directed .

Item No. 408 :- S&F Modular RJ 11 socket 1 gang with shutter complete all as specified and as directed.

Item No. 409 :- S & F for PVC non-metalic rigid conduit ISI marked heavy duty white/lvory colour and its accessories heavy duty ISI marked of size 25 mm dia for LAN telephone and TV connections including cutting chasses and making good disturbed surface to match with existing finish wih plaster etc complete all as specified and directed.

Item No. 410 :- Taking down old/unservicable switch any type and S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

Item No. 411 :- Taking down old/unservicable push bell & S&F bell push flush type 5 Amp complete all as specified and directed

Item No. 412 :- Taking down old/unservicable switch any type and S&F switch piano flush type 15 Amps, 230 volts, two way, ISI marked, complete all as specified & directed.

Item No. 413 :- Taking down old/unservicable switch any type and S &F 5 pin socket outlet, 5/6 Amps / 3 pin 5/6 Amps, flush type, ISI marked, complete all as specified and directed

Item No. 414 :- Taking down old/unservicable switch Socket combination any type and S & F switch socket combination 2 in 1, 3 Pin, 5 A flush type , ISI marked, complete all as specified and directed

Item No. 415 :- Taking down old/unservicable switch Socket combination any type and S & F switch socket combination 2 in 1, 3 Pin, 15 A flush type universal, ISI marked, complete all as specified and directed

Item No. 416 :- S &F Switch piano single pole one way 16 amps complete all as specified.

Item No. 417 :- S &F Socket out let 2 in one, 5/3 pin flush type single pole one way 16 amps complete all as specified.

Item No. 418 :- Taking down old/unservicable fan regulator any type and S & F electronic dimmers, 450W, 250V flush type on the existing phenolic laminated sheet etc as required complete all as specified and directed.

Item No. 419 :- S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 Hz, AC supply etc, complete all as specified & directed.

Item No. 420 :- S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

Item No. 421 :- S&F Lamp holder, PVC/polycarbonate type with back plate suitable for Pendant fittings with 9 watt LED bulb, complete all as specified & directed.

Item No. 422 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 10 Sqmm nominal area and drawing into suitable size of non metallic rigid heavy duty In Steel conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 10 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Four runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 10 Sqmm cable, one run ( with Green colour for Earth) of 10 Sqmm cable and one run of In Steel conduit will be measured as one unit.

Item No. 423 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of non metallic rigid heavy duty In Steel conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Four runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 6 Sqmm cable, one run ( with Green colour for Earth) of 6 Sqmm cable and one run of In Steel conduit will be measured as one unit.

Item No. 424 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with Two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of non metallic rigid heavy duty In Steel conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Two runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 6 Sqmm cable, one run ( with Green colour for Earth) of 6 Sqmm cable and one run of In Steel conduit will be measured as one unit.

Item No. 425 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with Two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sqmm nominal area and drawing into suitable size of non metallic rigid heavy duty In Steel conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 4 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Two runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 4 Sqmm cable, one run ( with Green colour for Earth) of 4 Sqmm cable and one run of In Steel conduit will be measured as one unit.

Item No. 426 :- M & L for Sub Main wiring (concealed type) in & including with approved colour as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 10 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 10.00 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Four runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 10.00 Sqmm cable, one run ( with Green colour for Earth) of 10.00 Sqmm cable and one run of In pvc conduit will be measured as one unit.

Item No. 427 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6.00 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 6.00 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Four runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 6.00 Sqmm cable, one run ( with Green colour for Earth) of 6.00 Sqmm cable and one run of In pvc conduit will be measured as one unit.

Item No. 428 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6.00 Sqmm nominal area and drawing into suitable size of non metallic rigid heavy duty conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 6.00 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Two runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 6.00 Sqmm cable, one run ( with Green colour for Earth) of 6.00 Sqmm cable and one run of In pvc conduit will be measured as one unit.

Item No. 429 :- M & L for Sub Main wiring (concealed type) with approved colour as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4.00 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty conduit and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 4.00 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and directed. Note :- Two runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 4.00 Sqmm cable, one run ( with Green colour for Earth) of 4.00 Sqmm cable and one run of PVC conduit will be measured as one unit.

Item No. 430 :- M&L for sub main wiring with two run of 2.5 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLS cable in and including electrical grade PVC conduits of desired colour not less than1.2 mm thick and 25 mm wide & 2.5 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one.

Item No. 431 :- Taking down old/unservicable MCCB DB any type and M&L distribution board made out of CRCA sheet, powder coated, vertical type, double door, SPN 4 way, including fixing in the wall after chase cutting and making good the surface by necessary patch work and surface finish as per existing including making connections all as directed.

Item No. 432 :- S & F for sheet metal enclosure MCB DB TPN 6 Way vertical type with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc concealed and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

Item No. 433 :- S & F for sheet metal enclosure MCB DB TPN 4 Way vertical type with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc concealed and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

Item No. 434 :- S & F for sheet metal enclosure MCB DB SPN 8 Way vertical type with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

Item No. 435 :- Taking down old/unservicable MCB DB any type and S &F metal clad box with a two pin and earth, plug & socket complete with one single pole 20 amp MCB all as directed .

Item No. 436 :- S & F sheet metal enclosure Double pole enclosure with a two pin and earth plug with socket complete with one double pole 240 volt 20 Amp MCB complete all as specified and directed.

Item No. 437 :- S & F sheet metal enclosure Triple pole and earth enclosure with a three pin and earth plug with socket complete with one thriple pole 415 volt 63 Amp MCB complete all as specified and directed.

Item No. 438 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified and directed.

Item No. 439 :- S & F MCB triple Pole and neutral rated capacity 63 Amps, 415 Volts, breaking capcity 10 KA "C" curve complete all as specified and directed.

Item No. 440 :- S & F MCB single Pole and neutral rated capacity 40 Amps, 240 Volts, breaking capcity 10 KA "C" curve complete all as specified and directed.

Item No. 441 :- S & F MCB single Pole rated capacity 5 to 32 Amps, 240 Volts, breaking capcity 10 KA "C" curve complete all as specified and directed.

Item No. 442 :- Taking down carefully Ceiling fan/ Ex Fans/ Air circuletor fan/Wall mounting fan, complete fittings at site removing Fans are diposited to E&M store for keeping in safe custody for re-use at site .

Item No. 443 :- Hanging only ceiling fan (M.D supply) and connecting up including provision of cable from ceiling rose or connector to fan.

Item No. 444 :- Taking down ceiling fan/exhaust fan of any sweep after discunnecting all necessary electrical connections from ceiling rose to fan, fan blades etc complete all as specified and directed.

Item No. 445 :- Labour only refixing the ceiling fan/exhaust fan obtained from item No 5 with replacement of unsv 3 core PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc complete all as specified and directed.

Item No. 446 :- S & F ceiling fan, 230 volts, 1200 mm sweep with service value of the fan shall be greated than 6.1 as per BIS with necessary aceessories and electrical connections for ceiling rose to fan terminal complete all as specified and directed.

Item No. 447 :- S & F for energy efficient exhaust fan of 300 mm sweep made of metal body ventil Air - DS type complete with louver with bolts nuts and washers size lt 15 cm 12 mm dia embedded in the wall including provision of PVC flexible coppler cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connecttion and making suitable size of hole to existing brick wall for fan base complete all as specified and directed.

Item No. 448 :- S & F for Wall mounted fan of 400 mm sweep made complete with fixed on the wall including provision of PVC flexible coppler cable of size 23/0.0076 two core from ceiling rose to wall mountd fan for connecttion and making suitable size of hole to existing brick wall for fan base complete all as specified and directed.

Item No. 449 :- S & F for Industrial Air circulation Wall mounted fan of 600 mm sweep made complete with fixed on the wall including provision of PVC flexible coppler cable of size 23/0.0076 two core from ceiling rose to wall mountd fan for connecttion and making suitable size of hole to existing brick wall for fan base complete all as specified and directed.

Item No. 450 :- S & F for energy saving new generation 10 watts LED bulk head fitting IP-65 luminaire with opel diffuser pre-wired with warranty option of 5 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specefied and directed.

Item No. 451 :- Taking down old/unservicable light fitting any type and S & F new 1 X 10 W LED light fittingsmirror type with high diffurser, 2 feet, 10 watt 220 volt AC decorative type with driver holder and LED lamp including complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size compete all as specified and directed.

Item No. 452 :- S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen output box type fitting, 230 volts and intregrated electronic driver connector block etc with necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specefied and directed.

Item No. 453 :- S & F for LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, 220V recessed type with high efficieny PMMA diffuser soft glare free light complete with drovers, holders, LED lamp suitable for roof ceilling, including connecting up with driver three core flexible copperr conductor cases of suitable size complete all as specefied and directed.

Item No. 454 :- S&F LED Focus Light 100 Watts complete all as specified and directed.

Item No. 455 :- S&F energy saving environmental friendly and robust , open type vertical highbay long life, exclusive innovative die-cast aluminium IP 65/66 industrial light with high power COB LEDs as light source, suitable for highlighting retails space 150 watt LED replacement metal halide industrial light luminarie complete with all accessories, connecting up with twin core twisted flexible copper conductor cable all as specified and directed.

Item No. 456 :- M&L distribution board made out of CRCA sheet, powder coated, vertical type, double door, 4way, including fixing in the wall after chase cutting and making good the surface by necessary patch work and surface finish as per existing including making connections all as directed containing and including the followings :- (a) MCCB, 4pole, 200 Amps, 16 KA breaking capacity with thermal release - 01 No (In coming) (b) Bus bar, 200 Amp rated, made out of aluminium duly insulated with adhesive tape RYB and black – 04 Nos. (c) MCB SPN 63 Amps-2 Nos and MCB SP 32 Amp-08 Nos (Out going) (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable size complete all as specified and directed.

Item No. 457 :- S & F for Energy saving new generation environmental friendly long life versatile pressure source and electronic driver of IP 65, LED street light of capacity 35 watts with pre-wired and necessary mounting arrangements and provision of 2.5 sqmm three core copper conductor cable multistranded from ceiling rose to light fittig including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nuts, bolts etc complete all as specified and directed.

Item No. 458 :- M & L for earthing complete with galvanized steel earth plate electrode 60cmx60 cmx 6mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level connecting to and including GI earth wire of size 4.0 mm by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade pipe for protection of GI wire to the extent of 7.5 mtrs asearthing lead including charcoal dust and salt packed all around the earth plate in the earth pit all as per Electrical plate ZNo 3 of SSR par - I (2009) including PCC foundation/chamber in mix 1:2:4 type B1 with angle iron frame CI frame, CI cover with provision of locking arrangement and 20 mm dia light grade GI pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement complete including excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal. Note :- Earth protection pipe & earthing wire upto and including 7.5 m length is deemed included in unit rate quoted by the contractor.

External Electrification

Item No. 459 :- Supplying and laying unreinforced precast cement concrete cable covers, Class LV, Type - 1 Flat, size 250mm x 150mm x 40 mm in trenches for cable protection, embossed with "LT 1100 Volts Electric" on the top surface complete all as specified and as directed.

Item No. 460 :- Supplying and laying reinforced precast concrete cable cover, class EHV, Type 1 with peak size 450mmx260mmx50mm all as specified and directed.

Item No. 461 :- M &L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in filling in surface channels and drains etc complete all as specified and directed.

Item No. 462 :- M &L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in coping of pole ect including form work & finishing the surfaces even & smooth with out using extra cement complete all as specified and directed.

Item No. 463 :- M & L for crossing hole under road/hard stranding for passing cable through GI pipe including GI pipe light grade 50 mm dia with all fittings complete all as specified and directed.

Item No. 464 :- All as Per Item No - 463 but here-in-before of size 80 mm dia complete all as directed.

Item No. 465 :- All as Per Item No - 463 but here-in-before of size 100 mm dia complete all as directed.

Item No. 466 :- Taking down existing old Extg unserviceable LT UG/service cable of any description and size complete all as specified and as directred.

Item No. 467 :- S & F XLPE insulated armoured and pvc sheated heavy duty electric cable with aluminium conductor 1100 volt grade laid in tranches passing through pipes /ducts including testing complete of following cross sectional area and size note- rate is inclusive of cable gland & cable lugs complete all as specified and directed.

(a) 2 core x 10 sq mm

(b) 4 core x 10 sq mm

(c) 4 core x 16 sq mm

(d) 4 core x 25 sq mm

(e) 3.5 core x 35 sq mm

(f) 3.5 core x 50 sq mm

(g) 3.5 core x 70 sq mm

(h) 3.5 core x 95 sq mm

(j) 3.5 core x 120 sq mm

(j) 3.5 core x 185 sq mm

Item No. 468 :- Supply install commissioning and testing CPRI Approved factory fabricated, floor mounted indoor type LT Feeder Pillar Box of suitable size fabricated out of 3 mm thick CRCA Sheet and angle iron 50 X 50 X 6 mm frame and 750mm above the Normal ground level complete factory made totally enclosed dust and vermin proof double door both side hinge opening arrangement on front and back with locking arrangement cable entry and exist from bottom with cable glands and gaskets, aluminium bus bar 1600 Amps rating (01 Set) fixed on porcelain insulator with internal wiring with suitable size of aluminium strips to be used for incoming and outgoing connection of all switches/MCCB's & Bus-bar. Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surface externally & internally over a coat of red oxide primer paint incl. necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following : - (Main Pannel P-210 AGDD 'A' Shed Accn)

Item No. 469 :- Supply install commissioning and testing CPRI Approved factory fabricated, floor mounted intdoor type LT Feeder Pillar Box of suitable size fabricated out of 3 mm thick CRCA Sheet and angle iron 50 X 50 X 6 mm frame and 750mm above the Normal ground level complete factory made totally enclosed dust and vermin proof double door both side hinge opening arrangement on front and back with locking arrangement cable entry and exist from bottom with cable glands and gaskets, aluminium bus bar 1200 Amps rating (01 Set) fixed on porcelain insulator with internal wiring with suitable size of aluminium strips to be used for incoming and outgoing connection of all switches/MCCB's & Bus-bar. Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surface externally & internally over a coat of red oxide primer paint incl. necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following : - (indoor pannel P - 62 & FGG P - 191Shed Accn)

Item No. 470 :- Supply install commissioning and testing CPRI Approved factory fabricated, floor mounted Indoor type LT Feeder Pillar Box of suitable size fabricated out of 2 mm thick CRCA Sheet and angle iron 50 X 50 X 6 mm frame and 750mm above the Normal ground level complete factory made totally enclosed dust and vermin proof double door both side hinge opening arrangement on front and back with locking arrangement cable entry and exist from bottom with cable glands and gaskets, aluminium bus bar 600 Amps rating (01 Set) fixed on porcelain insulator with internal wiring with suitable size of aluminium strips to be used for incoming and outgoing connection of all switches/MCCB's & Bus-bar. Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surface externally & internally over a coat of red oxide primer paint incl. necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following : - (JOD Area)

Item No. 471 :- Supply install commissioning and testing CPRI Approved factory fabricated, floor mounted Indoor type LT Feeder Pillar Box of suitable size fabricated out of 2 mm thick CRCA Sheet and angle iron 50 X 50 X 6 mm frame and 750mm above the Normal ground level complete factory made totally enclosed dust and vermin proof double door both side hinge opening arrangement on front and back with locking arrangement cable entry and exist from bottom with cable glands and gaskets, aluminium bus bar 400 Amps rating (01 Set) fixed on porcelain insulator with internal wiring with suitable size of aluminium strips to be used for incoming and outgoing connection of all switches/MCCB's & Bus-bar. Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surface externally & internally over a coat of red oxide primer paint incl. necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following : - (FPB- 14, location- near Guest house)

Item No. 472 :- Repair/Maint of floor mounted Indoor/outdoor cubical type LT Feeder Pillar Box of various sizes including disconnecting all in-coming and outgoing connection after taking necessary shut down, cleaning the carbon/rust from bus-bar, re-thimbling with new lugs/thimble of existing size incl. and segregating the serviceable and un-serviceable items with removing old burn out wiring and re-fixing the existing position replacement of un-serviceable parts including re-wiring and PCC works around the Feeder Pillar Box complete all as specified and directed.

Item No. 473 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 63 Amps with breaking capacity 16 KA complete all as specified and directed.

Item No. 474 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed.

Item No. 475 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified and directed.

Item No. 476 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA complete all as specified and directed.

Item No. 477 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA complete all as specified and directed.

Item No. 478 :- Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA complete all as specified and directed.

Item No. 479 :- M & L for earthing complete with galvanized steel earth plate electrode 60cmx60 cmx 6mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level connecting to and including GI steel strip of size 32 x 6 mm by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 40 mm dia medium grade pipe for protection of GI strip to the extent of 7.5 mtrs asearthing lead including charcoal dust and salt packed all around the earth plate in the earth pit all as per Electrical plate ZNo 3 of SSR par - I (2009) including PCC foundation/chamber in mix 1:2:4 type B1 with angle iron frame CI frame, CI cover with provision of locking arrangement and 20 mm dia light grade GI pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement complete including excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal ( for LT Panels). Note :- Earth protection pipe & earthing strip upto and including 7.5 m length is deemed included in unit rate quoted by the contractor.

Item No. 480 :- Supply and fix 32x6 mm earth continuity conductor or main earthing lead fixed to wall, on batten, recessed or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc complete all as specified and directed.

Item No. 481 :- Earthing for poles & other machinery/equipment using 4 mm GI wire as earthing lead and MS galvanized plate of size 60 cm x 60 cm x 6 mm, as earth electrode complete all as specified and directed.

Item No. 482 :- Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX of size not less then 2 m width X 1 m heigth X 0.5 m depth,made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embedded with 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation including complete all as specified and comprising of the following :– (a) Aluminum bus bar 400 Amps - 01 Set MCCB 250 Amps,3 pole 25 KA, Adjustable thernal & fixed magnetic setting MCCB 100 Amps,4 pole 16 KA, Adjustable thernal & fixed magnetic setting 3 Phase LED Digital Ammeter Class 1.0 3 Phase LED Digital Voltmeter Class 1.0 MPPH capacitor 10 KAVR, TP 20 Amps

Item No. 483 :- Taking down carefully existing Single pointed air termination aluminium rod, 12 mm dia, 300mm long keeping safe custody for reuse complete all as specified and directed.

Item No. 484 :- Taking down roof conductor aluminium strip 25mm x 3.15mm complete with saddles and keeping safe custody for reuse complete all as specified and directed.

Item No. 485 :- Fixing only Single pointed air termination aluminium rod, 12mm dia, 300mm longer obtained from item No - 1 etc complete all as specified and directed.

Item No. 486 :- Fixing only aluminium strip 25mm x 3.15mm complete with saddles and fixing screws as roof conductor obtained from item No - 2 complete all as specified and directed.

Item No. 487 :- Supply and fix Single pointed air termination aluminium rod, 12mm dia, 300mm long with necessary fixing arrangements as per site requirements complete all as specified and directed.

Item No. 488 :- Supply and fixing aluminium strip 25mm x 3.15mm complete with saddles and fixing screws as roof conductor complete all as specified and directed.

Item No. 481 :- Supply and fix Tubes light grade galvanized of size 15 mm dia with all fittings and fixed complete for suporting the air termination rod and protection of GI strip complete all as specified and directed.

Item No. 482 :- M & L for Test point terminal block made of gun or phosphorus bronze size 75 x 75 x 25mm drilled and screWED INCLUDING 3 Nos 8 mm dia 25 mm long hex. Head screw including removal old extg UNSV one complete all as specified and directed.

SCHEDULE "A" (Schedule of credit) Schedule of Credit Rs 1986806.50 (Minus) inserted by the MES. (Note : Credit amount shall be deducted manually to arrive net bid amount)

M/S.J.BIJAYA KUMAR PATRO

Jasvit Constructions Private Limited

JAIDEV SINGH CHADHA