Augmentation of facilities at Cfi lab by completely replacing the existing structure in Central Workshop at IIT Madras.

Amount

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. from 1.50 m to 3.00m depth

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. from 1.50 m to 3.00m depth

Excavation work in Ordinary rock by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sum on plan including dressing of sides and ramming of bottoms lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m. Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. from 1.50 m to 3.00m depth

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with M.sand under floors,footings including watering, ramming, consolidating and dressing complete.

Intercarting of excavated earth by mechanical transport including loading, unloading and stacking / spreading / leveling lead up to 2.5km km beyond the initial lead of 50m. Voids will be deducted at 20%.

Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentrations under raft slab and beam, under Cellular raft slab, alround the footings, column pits, trenches, pits, tunnels, wall trenches, back fill, plinth filling, junction of wall and floor, side walls of foundation, external perimeter of building, surrounding of pipes expansion joints, etc. as per IS specification and as per the instructions of chemical manufacturer and all as directed. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticides for the treatment shall be CHLOROPYRIPHOS 20% (or) 50% EC and the application shall be dilute one part of chemical 20% or 50% EC with 19 or 49 parts of water to get 1% emulsion and strictly in accordance with the manufacturer's specification.

CEMENT CONCRETE & REINFORCED CEMENT CONCRETE WORKS

Providing and laying in position ready mixed plain cement concrete, All works upto plinth level with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-10 grade plain cement concrete (cement content considered @ 220 kg/cum).

Providing and laying in position brick jelly concrete 1:3:6 (1cement: 3 coarse sand: 6 brick jelly concrete 20mm nominal size) in sunken floor including the cost of centering and shuttering at all heights after entire completion of laying pipes, sanitary fittings etc., Rate shall include for preparatin of surface, protecting the laid pipes and sanitary fittings, finishing the surface smoth to receive the top coat of water proofing application etc., complete and all as directed.

Providing and laying in position machine batched and machine mixed design mix M-35 grade Ready Mix cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 380 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works Up to Plinth Level

Providing and laying in position machine batched and machine mixed design mix M-35 grade Ready Mix cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 380 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level.

Centering and shuttering for getting neat exposed concrete finish (no external plastering will be allowed for RCC work) for all RCC/PCC works with film coated plywood shuttering board or using steel wall form work including strutting, propping etc., and removing for all RCC works. The contractor shall obtain approval from Engineer-in-Charge for the form work design & methodology proposed to be adopted in the work.

Foundations, footings, bases for columns

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform including flat slabs etc.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Reinforcement for RCC work Below plinth level including straightening, cutting, bending, placing in position and binding all complete by using Thermo mechanically treated bars (TMT) Fe500 of approved make and brand.

Above plinth level

Add for using extra cement in the item of RMC over and above the specified cement content therein.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

MASONRY WORKS

Masonry work with M10 grade fly ash concrete blocks in Cement mortar 1:4 (1 cement : 4 manufactured sand) in all shapes and sizes. Above plinth Level upto floor V Level

Half brick masonry with M10 grade fly ash concrete blocks in Cement mortar 1: 4(1 cement : 4 manufactured sand ) including longitudinal reinforcement of 2 Nos. 8 mm diameter bar every 3rd layer embedded in horizontal RCC band (1:1.5:3) in superstructure above plinth level. In superstructure above plinth level up to floor V level

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

FINISHING WORKS

Cement Plaster with Fine sand - 12 mm cement plaster in cm 1:4

Cement Plaster with Fine sand - 15mm thick cement plaster wall in cm 1:4

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers

Extra for plastering exterior walls of height more than 10 m fromground level for every additional height of 3 m or part thereof.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand).

Providing and fixing of Plaster mesh as approved by IIT Madras made out of galvanized iron of nominal thickness 0.35 mm with a Zinc coating of 120 gms per Sqm at the junctions of Masonry and concrete works 150 mm Width, chasing Works 200 mm Width, Diagonal Fixing at Doors & Windows Opening to a width of 300 mm x 600 mm including tying in position with suitable nails/screws etc., complete and as per manufacturer specification, from M/s.ARPITHA EXPORTS, ( Equivalent ) Bangalore. Rate shall include for preparation of surface, cleaning, curing etc. complete, all as directed by the Engineer-in-charge.

FLOORING WORKS

Providing and laying flamed finish Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for Dadoo, Skirting, wall clading, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels :Granite skirting & Thresholds upto 300 mm width

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for Dadoo, Skirting, wall clading, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels : Granite in Lift Facia

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the jointed with Laticrete or approved equivalent jointing compound of matching shade complete as per direction : Size of Tile 600x600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the jointed with Laticrete or approved equivalent jointing compound of matching shade complete as per direction : Size of Tile 800x800 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the jointed with Laticrete or approved equivalent jointing compound of matching shade complete as per direction

Providing and fixing Ist quality ceramic glazed wall tiles 300x450mm conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing the jointed with Laticrete or approved equivalent jointing compound of matching shade complete as per direction(Toilets)

Providing and fixing granite stone in risers of steps, skirting and dado in single size or in combination of different sizes with 18 mm thick plolished granite of approved colour, shade and texture, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) as per approved pattern / design and jointing with grey cement slurry @ 3.3 Kg. per sqm. including pointing with filler compound or approved equivalent, to matching shade as per Manufacturer's Specification, including edge chamfering and polishing the chamfered edge to give highly smooth surface, rubbing and polishing complete. curing, protection, scafolding and preparation of base surface etc. complete as per direction of Engineer in charge. Rate shall include for protection with gypsum/POP layer over plastic sheet and removing the same before handing over,work at all levels, as directed.With thickness not less than 18 mm Granite stone slab area up to 0.60 sqm : Red royal/ Multi red,Sindoori red,Jet black, Kashmiri gold, Jaisalmeer or equivalent shades

INTERIOR PAINT

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre : One coat

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. : Two coats

Ceiling white washing with lime to give an even shade :

EXTERIOR PAINT

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. Fresh work including complete surface preparation, as appropriate base (primer) coat and top two or more coats. Applying exterior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting (As per Annexure A.1.1). The exterior paint shall be applied over dry surface after through surface preparation. The work shall be executed as per the detailed specifications and special conditions mentioned in the Annexure 1. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc. The Paint manufacturer shall inspect the work in every stage, submit inspection / field test report, certify the product / application and give 10 year Guarantee

Finishing walls with textured exterior paint of required shade . Providing & Applying high quality acrylic modified resin based texture with anti-algae and UV resistance properties to be applied as intermediate finish in desired pattern (as approved by IITM) @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after thorough surface preparation, followed by top coating with two or more coats of Premium Acrylic Smooth exterior paint with Silicone additives of required shade (exterior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting as per Annexure A.1.1). The Paint manufacturer shall inspect the work in every stage, submit inspection / field test report, certify the product / application and give 10 year Guarantee.

JOINERIES

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 – part 1 and M.S. top cover of required thickness for rolling shutters including two more coat of synthetic enamel paint under one caot suitable of primer etc . 80x1.25mm M.S. laths with 1.25 mm thick top cover - RS1 - 5400x3880mm & RS2 - 3000 x 3880mm

Providing & fixing of powder coated aluminium pivoted door using Jindal/equivalent 63x38x1.5mm thick box section for outerframe, 48x44x2mm thick section for door verticals, door top & door intermediate, 100x44x2mm thick section for door bottom glazed with 6mm thick clear toughened glass, with necessary aluminium glazing clips, EPDM gaskets, lock, 22mm dia 300mm long SS handle, silicone sealant and other necessary hardwares etc.

Providing & fixing of powder coated aluminium sliding door using Jindal/equivalent 27mm series 2 track section 21373 (1.015 Kg/m) for outerframe, 21490 (0.851 kg/m) & 19453 (0.303 kg/m) for shutters, glazed with 6mm thick clear toughened glass, with EPDM gaskets, woolpile weather stripping, single point locking cum handle, bearing rollers, silicone sealant and other necessary hardwares etc.

Same as Item no.11, but using 2 track section 4 glass shutters.

Providing & fixing of powder coated aluminium sliding door using Jindal/equivalent 27mm series 3 track section 21242 (1.630 Kg/m) for outerframe, 21490 (0.851 kg/m) & 19453 (0.303 kg/m) for shutters with addon profile, glazed with 6mm thick clear toughened glass, with EPDM gaskets, woolpile weather stripping, single point locking cum handle, bearing rollers, silicone sealant and other necessary hardwares etc.

Providing stacking, storing & Fixing of 32mm thick Waterproof flush shutter including providing & fixing hardware fittings complete as shown in drawings at all levels with following specification at all levels including all leads & lifts of materials, etc., complete all as per directions of EIC. a. Infill: particlae board (tubular). b. Internal Frame Size on all sides of the infill: 60 mm wide with thickness as per Manufacturer's Standards. c. Internal Frame Timber: Kiln Dried Spruce/Pine Wood or Equivalent. d. Lock Rail Size in mm : 450 mm length x 60 mm wide, at centre of the stile. e. Lock Rail Timber: Kiln Dried Spruce/Pine Wood or Equivalent. f. Surface material: Plywood. g. Surface material thickness: 3mm. h. Top Surface Material: Laminate. i. Top surface thickness: 0.8mm / 1.0mm. j. Pressing: Hot pressing. Rate to exclude painting.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium Fixed windows with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.the fixed windowshal have glazed with 6mm thick clear toughened glass, with EPDM gaskets, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. : FW - 4000x3880mm

Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings & direction of Engineer-in-charge complete. : Upto 5mm depth and 5 mm width

Supply and fixing of uPVC (Unplasticised PolyVinyl Chloride) window frames having 3 tracks where 3 glassed shutter and 2 mosquited net shutter. The outer frame of the window shall be made of uPVC Profile Section of size 112 MMx 60MM having outer wall thickness of 2.3MM (+/- 0.3MM) with 3 box multi-chamber construction and provided with galvanized steel reinforcement for entire sections, with wall thickness of 1.2mm. Sliding glass shutter shall be made of 66MMx42MMx50MM having outer wall thickness of 2.3MM (+/- 0.3MM) and provided with galvanized steel reinforcement , with wall thickness of 1.2mm. The Sliding mesh shutter shall be made of 66MMx42MMx50MM and provided with galvanized steel reinforcement at wherever required, with wall thickness of 1.2mm. The mesh shutter shall be used to fit SS mesh for fly-proof with 0.28mm thickness & 1.5mm aperture. All the corners and joints of the frame & sash shall be mitred cut & fusion welded without any mechanical joint. All welded joints are to be neatly trimmed & feature grooved/raised nib finish so as to make the finished products free from all sharp edges & burrs. System shall have adequate drainage mechanism to permit the escape of water from horizontal member beneath each sealed unit. System shall be provided with suitable uPVC beading for glazing of size 24.5MM x 16MM and interlocking profile of size 45MM x 36MM with 6mm thick plain glass of SAINTGOBIAN (single), duly cut at correct degree & fitted with TPV gaskets. Windows has to be provided with Varity of security devise like crescent lock, wheel etc of ASSAABLOY / HETICH as per the requirement, compliant with relevant specification and as directed by department personnel. The complete window shall be fixed into the prefinished opened places, by drilling & fixing through the outer frame using high quality fasteners & silicon sealant is applied to fill up the gap between wall & window frame for leak-proof installation, and completion.

STW1 - 1500x1475mm

STW2 - 1200x1475mm

V3 -1500x600mm Sliding type

MISCELLANEOUS WORKS

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) : Supplying & Fixing Staircase Handrail - Inside.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) : Supplying and fixing Wall mounted handrail

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) : Supplying and fixing Railing System in Balcony Area

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including two more coats of synthetic enamel paint under priming coat with approved steel primer all complete.: Fixed to openings /wooden frames with rawl plugs screws etc

Supply and fixing in position of PVC coated MS Rungs for overhead tank.

Supply and fixing in position of Light weight FRSC Manhole cover for overhead tank including necessary civil works.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete: : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Roof treatment - : Providing and laying PU membrane (moist cured) over the existing terrace including providing Khura and Gola, laying the heat reflective tile over the membrane etc., complete. The work should be carried out involving the following items, sequences and specifications. a) Polymer modified mortar :- Resurfacing of the substrate with Sika Latex (or MIXBOND SBR of FABCHEM, Rheomix 141 of BASF or Nitobond SBR of FOSROC) polymer modified cement mortar (Cement: sand ratio : 1:3 with a Water (Mixed with Sika Latex) cement ratio of 0.4-0.45), with a minimum thickness of 20 mm, to get a levelled surface. The dosage of Sika Latex will be 4 kgs per bag of cement. The rate should be inclusive of bonding coat with cement and latex mix of ratio 1:1 over the cleaned surface before application of mortar. b)Treatment to rain water mouth / Khura- making opening for fixing the rain water pipe with a diameter of the opening should be more than 25cm around the rain water pipe to be fixed. The new rain water pipe to be fixed to the opening after installing swellable acrylic based PU water bar around the pipe, fixing the rain water pipe to the opening made and filling the gap between the rain water pipe and the opening with non shrink grout without any gap, applying a layer of cementitious water proof coating over the rainwater floor mouth (The rate also inclusive of applying a layer of cementitious coating Cement : SBR 1:1 ratio over the wall floor junction before applying coving) and finishing the surface neatly. c) Providing gola / coving 75x75 mm in cement concrete 1:2:4 admixed with 4 Ltr of SBR latex for 50 kg of cement (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 admixed with 4 Ltr of SBR with 50 kg of cement (1 cement : 3 fine sand) as per standard design. The rate also inclusive of applying a layer of cementitious coating Cement : SBR 1:1 ratio over the wall floor junction before applying coving. d) Supply and applying PU moist cured- Supplying and laying single component PU system using spray application only with MC-HYPERDESMO or equivalent product of SIKA / BASF/ ASIAN PAINT / FOSROC is a one component polyurethane fluid which cures with the humidity in the atmosphere. It produces a highly elastic membrane with strong adhesion to many types of surfaces. It is based on pure elastomeric hydrophobic polyurethane resin plus special inorganic

fillers, which result in excellent mechanical, chemical, thermal, UV and natural element resistance properties. Apply with airless spraying in two, at least, coats with minimum total consumption of 1.5-1.8 kg/m2 or as specified by the manufacturer. The rate inclusive of necessary surface preparation to receive the waterproofing coating etc., complete. e)Ponding test by storing water for a minimum depth of 20 cm and the water to be retained for not less than 48 hours or as required by engineer in charge to ascertain any leakage. Necessary repair / grouting to be done free cost to arrest any leakage observed. f)Geotextile:- Supply and apply a polyester based geotextile protection fleece. Product: Sarnafelt® 300 or equivalent approved by IITM. Product requirements: density ≥ 300 g/m2; thickness 2.4 mm; tensile strength ≥ 430 N/50mm; elongation at break ≤ 100 %; tear strength ≥ 250 N; puncture resistance ≥ 1600 N; cone drop: 13 mm. g)Providing and laying light weight concrete of grade not less than M2.5 using expandable polystyrene aggregate to maintaining adequate of density 800-900 kg/ cum and same shall be laid to maintain slope to drain the rain water over the geotextile (not less than 1 in 80). The minimum cement contnent shall not less than 250 Kg/cum. The mix design shall be approved by the engineer incharge. Minimum thickness of the concrete shall be 5cm. h)Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 9.5 mm) manufactured by ABC or equivalent with SRI (solar refractive index) > 78, solar reflection >0.70 and emittance >0.75 on 30 mm thick cool mortar as per manufacturer specification on sloped surface of terrace, laid on water resistant cement slurry prepared in the ratio of 1:3 ( 1 cement and 3 abc plus powder and add 3% Nano Acryl by volume) and grouting the joints (>3mm) with abc Grout and PPF (Poly Propylene Fiber) in the ratio of 2 to 3 gm PPF per kg of abc Grout including wetting (by using a piece of sponge) the grouted surface by abc Nano Clear in the ratio of 100 ml in two liter water. , including providing skirting upto 300 mm height along the parapet wall in the same manner.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20 mm cement plaster 1:3 (1 cement :3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

LIFT PIT WATER PROOFING

Providing and applying 3 coats of crystalline waterproofing slurry MasterSeal 501 of BASF make containing highly active, deep penetrative, reactive catalysts and shall have a mix density of 2.0 kg/litre. The product shall be applied in 3 coats one over the other at a time gap of 4 to 6 hours depending on the climatic conditions, including curing of the same for at least 5 days fog spraying water. Rate is inclusive of material and labour. The work shall include providing Covings/Chamfers at junction of slab and wall with 75 mm X 75 mm fillet with cement sand mortar 1:2 mixed with polymer modifier of styrene-butadiene co-polymer latex liquid MasterEmaco 141 of BASF make, produced from styrene and butadiene by high pressure emulsion polymerisation @ 5 L per bag cement. The product shall have minimum butadiene content of 40% by weight. The system shall be protected with a protective mortar. The protective mortar shall be done with liquid integral waterproofing compond MasterPel 707 of BASF make. The coated surface should be protected with 1:3CM admixed with lignosulphonate polymer based, waterproofing cum plasticing liquid integral waterproofer at a dosage of 100 ml per 50 kg of cement and shall comply with IS: 2645-2003. Rate shall be for supply and application including preparation of surface by mechanical upgrading to remove all loose mortar and laitance, oil, grease etc. and washing the surface with water to get neat surface, finishing, curing, scaffolding, waterproofing chemicals, wastage, conveyance, tools and plants, mixing device and gauge, Shuttering etc.as complete with all respects complying with relevant manufacturer's specification as directed by the department Engineer-in-charge.

Temporary Barricading

Providing and erecting temporary barricading around the site to a height of 6m. The G.I corrugated sheet of 0.35mm thick shall be fixed to the frame work made out 50mm dia M.S. class "B" pipe for veticals struts placed at about 3m c/c with required bracing using 40mm dia M.S pipe placed in five as per the direction of Engineer-in-charge. The rate also includes charges for providing painting and lettering, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The contractor should also maintain the barricade in good condition during the entire period of construction, any damages / defects noticed shall be attended within 24 hours of notice. The rate includes its cost of convenyanece of all required materials to work site, erecting, cost of J bolts, washers, cement concrete bed of size 45 x 45 x 75 cm in CC 1:2:4, painting, labour, materials, equipments, maintenance for damages and removing & disposing the same after completion the work . The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note: One time payment shall be made for providing barricading from start of work till completion of work, no additional charges shall be paid for the extended period of contract if any. The barricading provided shall remain to be the property of the contractor on completion of the work).

Supplying and fixing of green net over the temporary barricading sheet around the site as per the direction of Engineer-in-charge. The green net shall remain in the same location till the completion of the construction project. No additional charges shall be paid for the extended period of the contract. The rate includes its cost of convenyanece of all required materials to work site, cost of binding wire, labour, materials, maintenance for damages and removing & disposing the same after completion the work . The green net shall not be removed without prior approval of Engineer-in-Charge. (Note: One time payment shall be made for providing green net from start of work till completion of work. The green net provided shall remain to be the property of the contractor on completion of the work).

FORM FINISHED SHUTTERING

Providing, fabricating and erecting form work at all levels and places wherever needed/specified as per drawing including striking with 12mm Plastic coated, marine resistant waterproof ply/MDF board with adjustable steel props of acceptable Staging system and with sufficient bracing as approved by consultant. Cost to include designing of proper form work and staging system to suit the requirements,Submission of design calculations and shop drawings for approval,sealing the joints with heavy duty brown self adhesive tape, aligning to line and levels including M.S. Ties, PVC Spacer, Providing openings/ cutouts/ pockets, applying deshuttering chemical, Deshuttering all as approved by the consultant and Engineer In cahrge etc., complete at all levels and heights. : Form Work

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, Including the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.(Refer structural Drawing)

False Ceiling works

Supply and Installation of suspended Gypsum false ceiling consisting of 12 mm thick Gypsum plaster board suspended on GI framework. GI framework to consist of GI perimeter channels 0.55 mm thick 20 mm x 30 mm along perimeter of false ceiling of ceiling, screw fixed to wall/partition with nylon sleeves and screws @ 600mm c/c. Suspending GI intermediate channels of size 0.9 mm thick 45mm x 15 mm from the soffit at max dist 600 mm c/c with ceiling angle 0.55mm thick 25mm x 10mm fixed to soffit using GI cleat and steel expansion fasteners.12 mm thick plasterboard (IS 2095-1982) is screw fixed to ceiling section with 25mm drywall screws @ 230mm c/c. Boards to be finished with jointing tape and jointing compound and sand papered to achieve a smooth and seamless finish. Two coats of gypboard primer (Drywall Top Coat) to be applied to finished surfaces and then smoothened

Providing and fixing in position of grid suspension system of false ceiling system using Light weight 8 mm thick Calcium Silicate ceiling boards having 100% relative humidity resistance, incombustible as per IS standard and approved surface design and a suspended grid of size 600 mm x 600 mm made from hot dipped GI Steel section, main tee of size 24 x 32 x 1.5 mm thickness suspended at every 600 mm c/c along length of ceiling with 4mm dia, Pre-straightened G.I. wire with necessary level adjusters including providing necessary openings for light fixtures, diffusers etc. are to be made as per layout & as per directions of Architect.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

PLUMBING & SANITARY WORKS : SANITARYWARE AND CP FITTINGS : The contractors will have to quote their rate for the following specified make and model of sanitary wares and c.p.fittings including handling the materials very carefully and installing at respective locations. Incase any breakage, pilferage, theft or any such activity taking place during tenure of contract till handing over, the contractor is responsible by way of accepting recovery towards the cost of materials plus charges for re-installation.Rates under Supplying and fixing will include (a.) Cost of material (b.) Taxes (c.) Transporting the materials to site (d.) consumables (e) Loading from the market shop and unloading at site work (f.) Storing & Stacking (g.) Labour charges including lead and lift to all locations and (h.) Overhead & profits.(i.) Lead and lift to convey the materials with in the site for installation of materials in their position as needed (j.) Cutting the masonry or concrete surfaces to facilitate fixing (k.) Restoring damaged portions to their original condition with supply of materials like cement, river sand, stone chips, brick etc. (l.) convey all the broken materials taken out of damaged portion within the toilet & shaft area by head load via staircase, to be dumped out of the work site for onward clearance by another agency (m.) all the works are to be carried out as per description mentioned against each item of work mentioned in schedule of quantities (n.) all tools and plants needed for the job to be brought in by the contractor at their cost including maintenance expenses, replacement at cost wherever required – either in full or in part (o.) fixing materials like brackets, screws, bolts, nuts etc.

Supply and Installing,"Hindware" make medium colour Glazed cascade Pattern wall hung European water closet with concealed flushing cistren of 3/6 Liters flush with white colour polypropylene solid heavy duty seat and cover supplied by same maufacturer with non corrosive hinges and bolts, washer, providing suitable size fisher bolts and nuts, painted cast iron chair brackets, cutting grooves or make holes, grouting making good damaged surfaces with required materials , fixing the water closet with seat and cover to perfect level, testing and commissioning etc., complete. HINDWARE Make: Model:92081 Ivory GEBERIT concealed cistern Item no. 224.370.00.1 GEBERIT twinline actuator plate Item no 115.888.11.1

Supply and Installing "Hindware"make white glazed urinal of 645mm long with EFS having battery back up with one pair of consealed non corrosive brackets, installing the urinal to plumb, and at required level testing. cutting walls wherever required, restoring the same to their original conditions with required materials installing the testing and commissiong etc., complete. Pre flushing of 250ml and post flushing of 500ml of water. Hindware Make: Zen 96004 Ivory

Supply and fixing, Merino urinal partition fixing to wall dado using 4 nos. of suitable chromium plated brackets with C.P. bolts, nuts, washers, cutting to required shape, with approved pattern etc. complete. (Sample of material to be produced for approval by project manager.

Supply and Installing, Hindware make white glazed Rectangle Washbasin of 550 x 460mm size with a pair of Cast Iron brackets, fixing to Wall dado with required materials like teak wood plugs, packing pieces, screw nails, testing etc complete. Hindware Make: Cat. No: 10001

Supply and Installing of White color Floor Mounted European water closet with inbuilt low level PVC flushing cistern and Wash Basin for Physically Challenged Persons (Matrix) with necessary Grab Rails, hinged rails for support , pan connecter bend etc., colour solid seat and cover with polythene buffer and flap, CP flanges, CP bolts and nuts, bracket with nuts and bolts wall flanges etc.,complete, Wash Basin shall include 15mm dia CP liver operated pillar Cock with waste coupling, 32mm dia CP bottle trap with extension pipe,supporting bracket with necessary steel to support basin 1 No.15mm CP angle valve with 450mm long CP connection pipe and CP wall flanges all of approved make etc., complete. Make of material :- Hind ware Matrix (or) equivalent

Supply and Installing of NIRALI make stainless steel sink having over all size of 1040x 510x200mm with drainboard and chromium plated waste coupling supplied with sink by the same mufacturer, providing bracket made of 25 x 25 mm x 3 or 4 m thick size M.S.Angle, applying 3 coats of anti-corrosive paint, grouting the same into wall with concrete of 1:3:6mix, fixing the sink, drain board to a perfect level to match work platform in kitchen, cutting grooves in masonry, restoring the same to their original condition, testing and commissioning etc., complete. Model : Elegance- big(Glossy)

ACCESSORIES AND CHROMIUM PLATED BATHROOM FITTINGS : Supply and fixing Following chromium plated bath room c.p.fittings of approved make and connecting to water pipe using taflon tape over threaded portions, testing for leak proof, etc complete.

Supply and fixing (Florentine Range) Long Neck Pillar cock with aerator. Jaquar Cat no. FLR-5021N

Supply and fixing 15mm dia Rinsing spray with bracket and 1250mm.plastic tube (Health Faucet) long threads. Jaquar Cat no. 573

Supply and fixing 15mm dia Angle valve stop cock long inlet threads with wall flange. Jaquar Cat no. 5053

Supply and fixing 32mm dia bottle trap. Jaquar Cat no..769

Supply and fixing heavy quality 32mm dia waste coupling with dome grating fixing to urinals - produce sample for approval. Jaquar Cat no. 705 & viking make dome grating

Supply and fixing 32mm dia C.P brass waste coupling. Jaquar Cat no. 705

Supply and fixing chromium plated Double coat hook with suitable brass screws etc. Jaquar Cat no. 1161

Supply and fixing 15mm dia Sink cock with swinging casted spout type with wall flange etc. complete. Jaquar Cat no. 5347

Supplying 32mm size Chromium plated Flush Valve exposed unit pattern with control cock, Wall flange and elbow set, CP Flush bend where required, providing and fixing 32mm dia GI Pipe work with required pipe specials, supplying and fixing vacuum breaker set complete with coupling nut, cutting grooves in wall to conceal the pipe from Flush Valve to connect inlet of Water closet, making leak proof joints, testing etc. complete.

Concealed stop cock 20 mm dia

Supply and fixing chromium plated Towel rail 600mm long and 20m dia with cp brackets fixing in position using suitable C.P. screws, peak wood plugs etc., complete. Jaquar Cat no. 1111 / Equal approved make

Supply and fixing Kimberly clark or equal approved make Soap dispenser with 500ml liquid soap, fixing the same over wall dado using required fixing materials,etc.,complete. Jaquar Cat no. 1135

Supply and fixing Electric Hand drier NOVA or equal approved make, fixing the same over wall dado using required fixing materials with approved make etc., complete.

Supply and fixing Kimberly clark or equal approved make Jumbo roll dispenser with Jumbo roll tissues,fixing the same over wall dado using required fixing materials etc.,complete. Jaquar Cat no. 01153

Supply and fixing, (Continental Range) Long body bibcock with wall flange. Make : Jaquar Catalogue No : CON-107KN

Supply and fixing Kimberly clark make towel dispenser with paper towels,fixing the same over wall dado using required fixing materials etc.,complete. Jaquar Cat no. 02010 / Equal approved make

INTERNAL WATER SUPPLY

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work – Exposed on wall (Terrace & Shaft)

25 mm nominal outer dia .pipes

32 mm nominal outer dia .pipes

40 mm nominal outer dia .pipes

50 mm nominal outer dia .pipes

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Engineer in charge. Make of material :- Astral / Ashirvad / Supreme /Prince : Concealed work including cutting chases and making good the wall etc.

15 mm nominal outer dia .pipes (Provisional)

20 mm nominal outer dia .pipes

25 mm nominal outer dia .pipes

32 mm nominal outer dia .pipes

Providing and fixing ball valve (brass) of approved quality , high or low pressure, with plastic floats complete. Make of material :- RB/Leader/Audco /Zoloto

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Supplying and fixing of 25mm dia Air release valve etc. complete. Make of material :- RB/Leader/Audco /Zoloto

INTERNAL SANITARY DRAINAGE

Supply and fixing, Astral / Supreme / Finolex make, PVC-U pipes and Pipe specials like bends, Tee, Y-junction with or without door, Vent cowl, providing and fixing cleaning / rodding eye with endcap wherever required, etc., cutting the pipes, laying or fixing to perfect plumb, with slopes where required, making joints using solvent cement solution or with ring seal couplers of size available pipe of 110mm and 75mm dia., providing and fixing G.I. U clamps to the brackets, Providing and removing necessary scaffolding where required, providing supports for pipes laid in false ceiling using G.I.hangers fixed to R.C.C slab including providing and fixing necessary anchor fastners and clamps, conducting water test for leak proof joints and the materials, etc., complete.

40mm dia for wash basin (Concealed in Wall)

50mm dia for urinal (Concealed in Wall)

75mm dia for wastewater pipe (Inside Toilet)

110mm dia for soil pipe (Inside Toilet)

75mm dia for wastewater stack (Inside Shaft)

110mm dia for soil stack (Inside Shaft)

Supply and fixing, Custom (Fabricated) made PVC "Floor trap" with minimum 50mm water seal, made out of 110mm dia PVC Pipe with single or multiple inlets (boss tee) of size 40mm to 75mm dia with 75mm dia outlet, plugging the bottom to water tightness, using flattened PVC Pipe materials of 6 Kg class, fixing in position, laying cement concrete to 75mm alround in 1:3:6 mix using brick jelly to full depth of trap. Supplying and fixing SS grating of suitable size over trap at 4mm below Floor level testing to water tightness, and fiber glass mating at bottom, inlet and outlet etc. complete.

Supply and fixing, approved make 110mm dia PVC factory made Floor trap with water seal of 50mm and having multiple inlets and 75 dia outlet, fixing in position, laying cement concrete to 75mm alround in 1:3:6 mix using brick jelly to full depth of trap / sump, supplying and fixing SS grating of suitable size over trap / sump at 4mm below Floor level testing to water tightness, including providing fiber glass mating at bottom, inlet and outlet etc. complete.

Supply and fixing, approved make (Fabricated) PVC "Deep seal ‘P’ Trap" with 50mm water seal and vent horn, and 100mm dia outlet fixing to a perfect position, laying cement concrete alround in 1:3:6 mix with 20mm size stone jelly, providing and fixing suitable size SS grating with frame in PVC, providing 110mm dia PVC pipe over trap to make up the level of platform for Urinal portion, cutting concrete or making holes, restoring the damaged portion to their original condition etc. complete.

Supply and fixing floor clean-out using necessary items including providing brass threaded end cap, fixing the top of clean-out in line with adjacent fininished floor level inside toilet, providing allen-key arrangements for easy removal of clean-out etc., complete. (110mm & 75mm size)

Supplying and fixing, Pan connector made out of PVC with 110 or 90 or 75mm dia outlet, fixing to pipe work with rubber ring and other necessary materials, testing, to water tightness etc. complete.

Providing and laying concrete with 1:4:8 mix using 20mm size stone aggregate all around for buried soil and waste pipes including centring and shuttering and any mansory supports from slabs or firm ground, curing complete for the pipes including providing and removing temporary form work etc. complete.

75mm nominal dia pipe 75mm thick alround

110mm nominal dia pipe 75mm thick alround

External Water Supply

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets and dressing of sides ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming watering etc.and disposing of surplus excaveted soil as directed, with in a lead of 50m.- All kinds of soil : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. -External work - 50 mm nominal outer dia .pipes

Providing and fixing gun metal non return valve with C.I. wheel of approved quality(screwed end ) Make of material :- RB/Leader/Audco /Zoloto - 50mm nominal bore - Horizontal

Constructing masonry Chamber 120x120x100 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. : With F.P.S. bricks class

Supply and fixing, Toshniwal make Water Meter of 50mm dia size, including fixing in position with pipe work using necessary accessories and consumables, etc., complete.

Supply and fixing, approved make C.I ‘Y’ strainer, fixing to threaded ends of pipe work using Teflon tape and twine, testing for leak proof etc. complete. - 50 mm dia

Supply, Installation, Testing & commissioning of Grundfos or Equal approved make submersible Clearwater lifting pump set with suitable horse power motor to each pump to discharge 12,000 Litres per hour against total head of 35-40 Metres with control panel & all necessary accessories, conducting trail run, providing necessary civil foundations and base frame with all accessories and consumables, maintaining the system for the period of one year. Rate shall include all Electrical panel work connected to existing Electrical cable arrangement, etc. complete. Incoming Electrical cable to starter panel will be under scope of Electrical work. - No. of Pumps - 2 ( 1 working + 1 standby) Supply and installing Pressure based auto ON-OFF flood control system consisting pressure zone arrangement on the outlet of pump with panel, solenoid valve, float & control panel on the inlet of overhead water tank, fixing to pipe work using necessary accessories, commissioning the system, etc. complete. Rate shall be inclusive of necessary cables connected to nearby electrical source, etc.,

Supply, Installation, Testing & commissioning of Grundfos or equal approved make, factory tested twin Booster system (capacity of system is 7.50 Cu.M/ hour at 20 meters head) comprising 2 pumps 1 working + 1 standby (each Pumpset 7.50 Cu.M/ hour at 20 meters head) with 1 No. of 328 litres capacity pressure tank, switch, guage, control panel, supply and fixing vibrating pad etc. conducting trail run, testing, commissioning maintaining the system for the period of one year, rate include all Electrical panel work connected to existing Electrical cable arrangement etc. complete. For Domestic water purpose (AT TERRACE LEVEL - NEAR OH TANK) Optional

Exteranl Drainage : Excavating trenches of required width for pipes, cables, etc, including excavation for sockets and dressing of sides ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming watering etc.and disposing of surplus excaveted soil as directed, with in a lead of 50mt. -All kinds of soil - Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Supply and fixing, Finolex / Supreme / ASTRAL make UPVC 6 kg class Pipes and pipe specials confirming IS: 4985, cutting the pipes to required lengths, making joint between pipes and pipe specials using solvent cement, ring seal couplers, aligning the pipe to perfect plumb, fixing the pipe using required clamps fixed to bracket, making earthwork excavation in trenches to required width and depth, including consolidation by rodding and compacting, refilling the trench in layers with excavated earth, consolidating, disposing off surplus earth as directed by site engineer, testing for leak proof etc. complete.

75mm diameter

110mm diameter

160mm diameter

Constructing brick masonry manhole in cement mortar 1:4 (1cement:4 graded stone aggregated 20mm nominal size), foundation concrete 1:4:8 mix (1cement:4coarse sand: 8graded stone aggregated 40mmsize nominal size) in side plastering 12mmthick with cement mortar 1:3(1cement:3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement :2coarse sand :4graded stone aggregate 20mm nominal size) finished with floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45cm deep including C.I cover with frame (light duty )455x610mm internal dimensions total weight of cover and frame to be not less than 38kg(weight of cover 23kg and weight of frame 15 kg): With Sewer bricks conforming to IS:4885

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size ) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking in to and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2coarse sand: 4 graded stone aggregate 20 mm nominal size) cement plaster on both side with cement plaster 1:3 (1cement:3 coarse sand) finished with a floating coat of neat cement and making necessary channels for drain etc.complete for pipes 100 to 230 mm diameter

Providing and fixing square-mouth S.W.gully trap grade ‘A’’ complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design : 100x100 mm size P type - With F.P.S.bricks - With Sewer bricks conforming to IS:4885

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenchs or drains (not exceeding 1.5 m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excaveted soil and disposal of surplus excaveted soil as directed, within a lead of 50m : All kinds of soil (for manhole)

Storm Water Drain

Supply and fixing, Astral / Supreme / Finolex make, PVC-U - IS 13592 SWR Grade Type – B Class Pipes and pipe specials, cutting the pipes to required lengths, making joint between pipes and pipe specials using solvent cement, ring seal couplers, aligning the pipe to perfect plumb, fixing the pipe using required clamps fixed to bracket, testing for leak proof, etc. complete. For Rain Water disposal.

75 mm dia pipe - Exposed in shaft

110 mm dia pipe - Exposed in shaft

160 mm dia pipe - Exposed in shaft

200 mm dia pipe - Exposed in shaft

Making suitable Rain Water Inlet arrangement at Terrace including providing and fixing 100 dia CI grating etc. complete.

Making suitable Rain Water Inlet arrangement at Terrace including providing and fixing 160 dia CI grating etc. complete.

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets and dressing of sides ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming watering etc.and disposing of surplus excaveted soil as directed, with in a lead of 50mt. - All kinds of soil - Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Supply and fixing, Finolex / Supreme / ASTRAL make UPVC 6 kg class Pipes and pipe specials confirming IS: 4985, cutting the pipes to required lengths, making joint between pipes and pipe specials using solvent cement, ring seal couplers, aligning the pipe to perfect plumb, fixing the pipe using required clamps fixed to bracket, making earthwork excavation in trenches to required width and depth, including consolidation by rodding and compacting, refilling the trench in layers with excavated earth, consolidating, disposing off surplus earth as directed by site engineer, testing for leak proof etc. complete.

110mm diameter

160mm diameter

200mm diameter

Providing 1.00 metre internal dia and 1.20 metre deep rain water harvesting pit including providing necessary brickwork, filter media like sand and stone aggregates, Sinking 150mm dia. Bore to a depth of 10 to 15 meters, supplying and fixing 90mm dia pvc pipe with slotting arrangements, filling the gap between bore and pipe 6 to 8mm stone chips.

MISCELLANEOUS WORKS

Fabricating brackets using Mild Steel material, cutting, welding, forming shapes, providing hot dip galvanizing to entire bracket, provide and fixing SS threaded rods, cutting pockets in masonry / concrete surfaces, grouting brackets in concrete of 1:2:4 mix, restoring the damaged portion to their original condition required materials etc. complete. Note: Sample need to be produced for approval by PMC

Supply and fixing, Pipe Inserts up to 1000mm for UG Sump using 'uPVC' SCH-80 providing 4 to 5mm thick sandwich PVC plate at center projecting 25mm alround pipe insert, scrapping the outer surface of pipe, applying bitumastic paint with stone chips for making proper bonding between insert and RCC wall, fixing the insert in perfect position, providing temporary blinding of both edges etc. compete.

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

Supply and fixing, Pipe Inserts up to 1000mm for Overhead water tank using 'uPVC' SCH-80 providing 4 to 5mm thick sandwich PVC plate at center projecting 25mm alround pipe insert, scrapping the outer surface of pipe, applying bitumastic paint with stone chips for making proper bonding between insert and RCC wall, fixing the insert in perfect position, providing temporary blinding of both edges etc. compete.

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

Providing 125mm dia. Core cutting upto 300mm deep in all types of concrete, restoring the same after laying pipe, providing waterproofing compounds for leak proof sealing, testing for leak proof by means of providing dyke arrangements etc., complete and as directed by the site engineer

Providing approved make expansion bellows, fixing the same with pipe work using required accessories and all consumables, testing for leak proof etc.. Complete.(Sample to be approved by Architects/Consultants) : Suitable for 50mm size pipe

ELECTRICAL WORKS : LT PANELS (COMMON SPECIFICATION)

Enclosure : The panel shall be form 4A type front operated floor mounted , totally enclosed, compartmentalized, vermin proof, indoor, cubicle type power panel.For load bearing members- 14 SWG CRCA sheet.Internal partition & doors - 16 SWG CRCA sheet .The panel shall be fully powder coated after seven tank treatment. Colour of the panel shall be as per approval.Each door shall be casketed using nitrile rubber and hinged on each cubicle with insulated door knob.Danger sign board, earthing bus and lugs, cable chamber, bus bar chamber with air vent with insect proof, aluminum anodized name plates Gland plate of all panels shall made out of 3mm thick aluminum sheet.Panel shall have one empty chambers and bus bar expanding provision for future. Cable chamber entry shall be provided at the top and bottom. Bus bar : Horizontal & vertical bus bars shall be electrolytic copper/aluminium sleeved as mentioned in line item.Aluminium bus size shall be rated based on 0.7A/sq.mm.Copper bus size shall be rated based on 1.2A/sq.mm.Neutral bus shall be of same size of the phase bus except UPS outgoing panel where it shall be double the size of phase bus. Provision for extension shall be given in the bus bars. Necessary holes shall be made in the panel. Bimetallic lugs to be used wherever necessary.Interconnectivity of MCCB/MCB and bus bar shall be of FRLS wires up to 63A and through BUS bar for above rated feeders.All Bus thickness shall not be more than 8mm.. Feeder : All MCCBs shall be of 100% Ics type.All breakers shall have protection relay from OC and SC fault.Microprocessor based protection for 250A and above rate breakers and below rated shall be of thermal magnetic type protection. Suitable rotary handle shall be given as required.Lock facility shall be provided in all MCCB.All TP Breakers MCB/MCCB to be supplied with neutral link. Control and metering : LED indication lamps with necessary control MCBs for R,Y,B & T indication shall be provided. LED illuminated push buttons with necessary control MCBs for ON, OFF indications shall be provided.All wires shall be FRLS insulated for control wirings.All incomers shall have MFM capable to measure V,A,KVA, KW, KWh, KVARh, PF with inbuilt RS 485 port for BMS connectivity.Measuring CT shall be of cast resin type class 0.5.Incomers of all main panels to be supplied with SPD of B+C class with 50kA. Testing : HI POT test during inspection.IR value test before and after HI POT test.Functional test. Note to vendor : Panel shall be manufactured by fabricators holding valid CPRI test certificate.Vendor shall scrutinize the GA drawings of all panels against the BOQ, SLD, Electrical room foot print etc.Consultant will only counter sign the same before production. If any deviation is found during inspection, vendor shall take responsibility to do the correction without any additional cost.Additional MS base frame shall be provided without any additional cost if site demands for the same.

AC POWER PANEL (Blue) : Incomer : 160A 25kA TP+N MCCB ; Outgoings : 40A 25kA TP+NL MCCB - 11 Nos; Bus bar shall be aluminum and rated for 200A.

SUB POWER PANEL (Green) : Incomer : 160A TP+N MCCB; Outgoings : 63A TP+NL MCCB - 4 Nos; 40A TP+NL MCCB - 6 Nos; Bus bar shall be aluminum and rated for 200A.

DISTRIBUTION BOARDS : Supply, erection, testing and commissioning of phase segregated seven segment compartmental type MCB DB double door type, IP 42 powder coated DB comprising of "B" curve MCB's for lighting, "C" curve for power and UPS.Rate shall remain same for surface fixing, concealing, angle iron mounting including framework cost, on interior partitions etc. Rate shall be inclusive of adopter boxes, junction boxes for termination near DB, dressing &concealing of wires in raceways, covered trays etc. The entire wiring shall be dressed neatly without any phase crossing and taken in separate conduits dedicated for that particular phase. The circuits shall be ferruled,button taped and DBs labelled with aluminum sheet. Individual circuit labelling shall be done on an A4 sheet paperand pasted on the interior side of the DB. Additional entry cells shall be given for each phase to edit and amend as the output purpose changes. Door earthing to be done. Rate to include any allied civil works & all interconnections & accessories as required. All DBs to be supplied with padlock, lock & key. Instruction to lock the DB while maintaining to be pasted on the inner side of DB. All MCB shall be of fault current limiting and shall confirm to class 3 energy limiting of IEC 60898.

8Way LDB - I / C - 40A TP+N MCB - 1 No; O / G - 40A DP RCCB 30mA - 3 Nos; 6-25A SP MCB - 24 Nos; Including all interconnections & accessories etc as reqd.

8way ELDB : I/C - 25A DP - 1 No; O/G - 6A SP MCB - 14 Nos; Including all interconnections & accessories etc as reqd.

8Way PDB I / C - 63A TP+N MCB - 1 No O / G - 63A DP RCCB 30mA - 3 Nos 6-32A SP MCB - 24 Nos Including all interconnections & accessories etc as reqd.

12Way UDB I / C - 40A TP+N MCB - 1 No O / G - 40A DP RCCB 100mA - 3 Nos 10A SP MCB - 36 Nos Including all interconnections & accessories etc as reqd.

16Way VTPN DB I / C - 100A TP+N MCCB - 1 No O / G - 32A TP MCB - 16 Nos Including all interconnections & accessories etc as reqd.

40A TP+N MCB in MS enclosure including all accessories.Rate shall be same for concealing in wall or surface fixing as required as per site conditions.

20/25A DP MCB in MS enclosure including all accessories.Rate shall be same for concealing in wall or surface fixing as required as per site conditions.

10A DP MCB in MS enclosure including all accessories.Rate shall be same for concealing in wall or surface fixing as required as per site conditions.

63A 4P 100mA RCCB in weather proof enclosure including all accessories.Rate shall be same for concealing in wall or surface fixing as required as per site conditions.

Cables : Supply, laying, Testing and commissioning of 1.1KV grade LT XLPE insulated, cores laid up, PVC tape inner sheathed, GI wire/strip armoured, extruded PVC tape type ST2 outer sheathed aluminium/ copper conductor cables of following sizes.Earthing cable shall be 1.1 kV single core unsheathed PVC insulated copper cables laid through PVC conduit suitable size.Rate shall be same for clamping on the wall, laying on trays, trenches, ducts and as per the site conditions. Vendor shall test and submit IR values for all cable using valid instruments.

3.5C x 240sq.mm Al.

3.5C x 95sq.mm Al.

3.5C x 50sq.mm Al.

3.5C x 25sq.mm Al.

4C x 16sq.mm Al.

4C x 10sq.mm Al.

4C x 6sq.mm Al.

Supply, laying, testing and commissioning of 1.1 KV grade flexible single core unsheathed PVC insulated copper cables of the following sizes laid through suitable GI flexible hoses in trefoil method and tied at regular interval using cable ties. Cost shall be inclusive of GI flexible hose supply and rate shall be same for laying on tray and dressing the same at ceiling level/floor level and clamping on wall as per site condition. Up to 25 Sqmm shall be of FRLSH and above size shall be FR insulated cables.

4R 16 Sq.mm. Cu.

3R 4 Sq.mm. Cu.

TERMINATION : Supply & terminating the ends of cables of following sizes using Siemens type single compression cable glands, crimping type Aluminum/Copper lugs of required size, crimping paste, tapes, bolt nuts, double washers, spring washers, gland earthing clips complete.Each cable shall be identified with cable tags above the panel / DB. Cable shall be properly dressed before termination and bent at anangle of 15 times the radius of the cable. No extra holes shall be made on top of panel and if any made shall be sealed properly.The final tightness at every terminal shall be done with a torque wrench and tightened up to the recommended level. Flexible wires for power shall be glanded with cast aluminium glands and earthed properly. Flexible wires for earthings may glanded with PG glands.Upto 35 Sqrmm of flexible cables can be grouped and glanded using suiable size of sigle cast aluminium gland. Above 35 sqrmm of flexible cables shall be individualy glanded using cast aluminium glands.

3.5C x 240sq.mm Al.

3.5C x 95sq.mm Al.

3.5C x 50sq.mm Al.

3.5C x 25sq.mm Al.

4C x 16sq.mm Al.

4C x 10sq.mm Al.

4C x 6sq.mm Al.

4R 16 Sq.mm. Cu.

3R 4 Sq.mm. Cu.

SUB MAINS : Supply, laying , testing and commissioning of following sizes of single core and multicore cables as per specification given.

3Cx 1.5 sqmm PVC insulated FRLSH sheathed bright annealed multistand copper wire.Rate shall be same for laying in raceway and through conduit.

3Cx 2.5 sqmm PVC insulated FRLSH sheathed bright annealed multistand copper wire.Rate shall be same for laying in raceway and through conduit. White sheathed for raw power in WS area.

3Cx 4 sqmm PVC insulated FRLSH sheathed bright annealed multistand copper wire.Rate shall be same for laying in raceway and through conduit.

3Cx 6 sqmm PVC insulated FRLSH sheathed bright annealed multistand copper wire.Rate shall be same for laying in raceway and through conduit.

3 runs of 4sqmm FRLSH PVC insulated multistrand copper wire in MS conduits of 25mm dia ( Rate included)with all accessories as required at site. Rate shall include chipping and chasing of walls wherever required at site.Chicken mesh shall be used for finishing the wall chasing.

3runs of 2.5sqmm FRLSH PVC insulated multistrand copper wire in MS conduits of 25mm dia ( Rate included) with all accessories as required at site. Rate shall include chipping and chasing of walls wherever required at site. Chicken mesh shall be used for finishing the wall chasing.

SOCKETS & BBT

Supply, Installation, testing and commissioning of 1 No 6A universal sockets suitable for flat / round pins controlled by 1 no 6A switch in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back box as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval. For Utility.

Supply, Installation, testing and commissioning of 1 No 6A universal sockets suitable for flat / round pins in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back box as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval. For toilet exhaust

Supply, Installation, testing and commissioning of 1 No 6A switch in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back box as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval. For toilet exhaust

Supply, Installation, testing and commissioning of 3 No 6/10/13A International sockets suitable for flat / round pins controlled by 1 no 16A switch in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back boxes as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval.

Supply, Installation, testing and commissioning of 2 No 6/10/13A International sockets suitable for flat / round pins controlled by 1 no 16A switch in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back boxes as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval.

Supply, Installation, testing and commissioning of 1 No 16/6A sockets suitable controlled by 1 no 16A switch in a single modular plate and fixing the same for a single location with a dummy if necessary and other associated accessories including suitable back box as required as per the site conditions. Colour of the switches, sockets and front plates would be as per approval. For utility purpose.

SITC of 20A-2P+E interlocked switch socket outlet with plug top with IP-44 protection. The top shall not be removable under turned ON condition. Similar to cat no: Scame omina series 500.2083. Rate shall include support accessaries as required at site.

SITC of 32A-3P+N+E insutrial socket outlet with plug top with IP-44 protection with 4P 32A, 100mA RCCB. Similar to cat no: Scame omina series (Plug top -213.3237, Socket - 413.3267, Box - 632.1500) . Rate shall include support accessaries as required at site.

Supply and Installation testing and commissioning of floor ega box as per architect/ PMC / client approval with suitable for fixing power socket and data socket as per workstation configuration with mounting accessories. (Sockets configuration shall have with 3 No's of 2 x 13A + 1No's of 2 data port sockets controlled by one switch. Similar to Legrand Make CAT No :689638)

Supply and Installation testing and commissioning of single phase indoor bus bar trunking system for power and DATA outlets similar to EAE make - E-LINE FLD model - 3134084. Rate shall inclusive of all acessaries for mounting one meter bus bar on wall with feeder unit and end cap. Bus bar trunking in single location shall consist of the following outlets. Length of bus bar - 1mtr. 16A, 240V socket - 6 nos Data port -1no Voice port -1 no USB port - 1 no.

Supply, Installation, testing & commissioning of 400 V 25kA LT, 50 Hz. The busbar trunking enclosure shall be fabricated out of Hot-galvanized sheet steel by at least 0.8mm and tested for IK10 as per IEC62262. It shall be rigid and robust in construction , compact in size & serves as a protective conductor due to it’s cross section and electrical continuity. The enclosure shall provide a protection not less than IP- 55 for Feeder Element & for Distribution Elements IP-55 can be achieved by using plug outlet cover on tap-off free outlet as per IEC-529. All the run elements ( Straight Feeder, Elbows,etc ) are supplied complete with a factory fitted monobloc. The Busbar shall be made from copper plated aluminium with final coat of tin for the rated current. The conductors should be spaced with plastic insulators reinforced with 20% Glass fibre. The insulators should have V1 self extinguishing degree (as Per UL94) and are in compliance with the incandescent wire test as per EN 60695-2-1. The actual route of the busduct to be ascertained at site before ordering.

400A Al air insulated bus bar trunking with 25kA breaking capacity

PLUG OUTLET COVER IP55

400A AL END FEED UNIT with 250A 25ka FP mccb and RHOM

END COVER IP55

400A AL HORIZONTAL ELBOW RH STD

400A AL VERTICAL ELBOW RH STD

FIXING KIT HANGER SIZE A

40MM SPACER FOR HANGER

Tap off box with 1 nos. 32A 3ph socket with plug & FP mcb, 2 nos. 16A 1ph socket with plug & DP mcb

POINT WIRING : Supply, Erection, Testing and commissioning of 3R 1.5sqmm PVC insulated FRLSH copper wire in suitable dia PVC conduit concealed in concrete along with Modular 6A one way switch with moulded front plate GI anodized enclosure and other associated accessories as required as per the site conditions. Cast aluminium glands shall be used at the termination point of conduits and earthed.Rate shall include circuit main from DB. Primary point

From DB to Switch then switch to first light fixture

From Switch board to first light fixture

From switch board to switch board and then first light fixture.

Fan point with regulator

Exhaust fan point

Secondary point looped from the primary point

Supply, Erection, Testing and commissioning of 3R 1.5sqmm PVC insulated FRLSH copper wire in suitable dia MS conduit along with Modular 6A one way switch with moulded front plate GI anodized enclosure and other associated accessories as required as per the site conditions. Cast aluminium glands shall be used at the termination point of conduits and earthed.Rate shall include circuit main from DB. Rate shall include of GI flexble hose and gland for dropping to light fixture from ceiling.Primary point

From DB to Switch then switch to first light fixture

From Switch board to first light fixture

From switch board to switch board and then first light fixture.

Exhaust fan point

Secondary point looped from the primary point

Emergency lighting switch control with 6A switch in separate box with all accessories. Wiring will be covered separately. Colour of the switches, sockets and front plates would be as per approval.

Supply, Erection, Testing and commissioning of 3C 1.5sqmm PVC insulated FRLS copper wire laid in powdercoated solid trays with all accessories as required as per site conditions ( Rate included). Rate shall include chipping and chasing of walls wherever required at site. Chicken mesh shall be used for finishing the wall chasing.(Emergency wiring)

Supply and installation of anodized Fan hook box

Osram DALI MCU Smooth dimmer control - Cost of dimmer control with front plate, back boxes and accessories.

LIGHT FIXTURES

Supply, installation, testing and commissioning of following light fixtures with all support accessaries as required at site. Vendor shall provide lux level report before and after installation of light fixtures for approval. Approval of color temperature shall be taken from architect before production. Note: The word 'similar to' is for visual reference purpose only. It does not meanthat particular make alone. The vendor may choose any make given in the approved makes.

10W Suspended light (Similar to arraystorm make swank s model)

10W Surface mount light (Similar to arraystorm make swank s model)

28W, 1200 mm long linear light (Similar to PHILIPS make Line light RC 311)

32W 2'x2' light (Similar to PHILIPS make Full Glow RC380 G3 HL)

15W circular LED down light (Similar to PHILIPS make GreenLEDi)

1200mm dia ceiling fan.

200mm sweep PVC blade exhaust fan for toilet exhaust

Supply and Installation testing and commissioning of 25A single phase indoor bus bar trunking system for light fixtures similar to EAE make - E-LINE KAM MODEL - KAM0203. Rate shall inclusive of all accessaries for hanging bus bar from ceiling.and end cap etc..

3 meter length

1 meter length

End feed box

Flexible Elbow

10A Tap off plugs with one meter cable.

EARTHING Common Note: All earthing cables/wires pvc outer sheath should be having of green colour only. Below 25 Sq.mm cable shall be FRLS and above 25 Sq.mm cable shall be FR. All single core flexible cables for earthing shall be laid in FRLS PVC conduit only. Rates shall be inclusive of terminations using suitable lugs, PVC glands, PVC conduits etc. Rates shall be same for all types of laying. Earth flats shall be laid on trays before laying the cables, inspected for quality of joints and reported. Copper or aluminium earth flats shall be overlapped by double the length of it's width at the welded joints. Rate shall be inclusive for welding, slag removing, painting with aluminium paint and connecting at the panel end using suitable bolt & nuts, washers etc. Rate shall be same for laying in trenches, clamping on wall and laying on trays. When laid on trays, all earth flats shall be bolted with tray at 3mtrs interval using suitable bolt nut & washers. Copper flats shall be exothermically welded at the joints.

Supply, laying of 16 sqmm multi stranded FRLS copper wire in suitable MS conduit with all accessories as required.

Supply, laying of 10 sqmm multi stranded FRLS copper wire in suitable MS conduit with all accessories as required.

Supply, laying of 6 sqmm multi stranded FRLS copper wire in suitable PVC conduit with all accessories as required.

Supply, laying of 4 sqmm multi stranded FRLS copper wire in suitable PVC conduit with all accessories as required.

Supply, laying of 8 SWG bare copper wire

Supply, installation of earth bus link comprising of 25x6 copper flat with 10 Nos holes with bolts, nuts and washers. This shall be installed in MS enclosure.

Supply, laying of 50x6 G.I. flat on wall, trenches and trays. Rate shall remain same for all types of laying.

Supply, laying of 25x6 G.I. flat on wall, trenches and trays. Rate shall remain same for all types of laying.

Cable trench for earth flat laying - Excavation and backfilling of the sand trench along the side of the road. The trench shall be 600mm deep

450mm wide. The trench shall be backfilled, watered and rammed to suit original level.

RACEWAYS

Supply and Laying of 100 x 45mm Aluminium truncking box of 1.6mm thick and should be earthed with 14 SWG bare copper wire and bond firmly to the junction box with hardware as required. Areas where the hollow portion of two raceway meets, both ends have to be connected with 14 SWG earth wire to maintain continuity. Intersecting points also to be connected through junction boxes.

Necessary cutting chipping works for laying the above raceway including closing the same with strong plastering work. Places where 3 or more raceways are laid they shall be bound firmly with chicken mesh & masonry work done before making the floor strong, smooth finish & in level with the normal level. Broken rubble to be disposed as instructed.

Supply and Installation of GI Junction box of following sizes with removable 3mm thick stainless steel cover having openings on all 4 sides to lead wires out to the sockets. The trunking box shall be earthed with 14 SWG bare copper and connected to the raceway. Gap between screeded floor and junction box shall be bridged with wooden members on the sides and raised to match floor level. Long screws/ bolts to be used to cover the junction box as required. Rate to be inclusive of PVC conduits up to junction box.

CABLE TRAYS

14SWG ladder/ solid / ductable type Hot dip GI cable tray with fixing accessories like fasteners, down rod supporting angle / slotted channel, etc. as per the site condition of following sizes for power and data cables. The trays may be fixed on ceiling, floor as required at site. Supports to be installed at a maximum span of 750mm. Ladder type Ceiling tray - for power cables.

300mm x 50mm

150mm x 50mm

14SWG ladder/ solid / ductable type Hot dip GI cable tray with fixing accessories like fasteners, down rod supporting angle / slotted channel, etc. as per the site condition of following sizes for power and data cables. The trays may be fixed on ceiling, floor as required at site. Supports to be installed at a maximum span of 750mm. Closed Duct type cable tray without tray cover on top with fixing accessories like fasteners.

100mm width, 50mm height

200mm width, 50mm height

300mm width, 75mm height

Powder coated CRCA sheet duct type tray supported with threaded down rods and slotted angles/powder coated MS angle. Rate shall be inclusive of T joints, junction boxes, bends, tapered routing, welding, cutting drilling holes, supporting with anchor fasteners etc. The tray shall be earthed with one run of 8 SWG earth wire. Trays shall be GI tray above ceiling . The whole tray section shall be completely covered from the top and shall be vermin and other insect proof. tray cover shall be 2 meter length and thickness shall be 1.6mm. Refer support details.

150mm width, 50mm height (Without top cover)

150mm width, 50mm height (With top cover)

200mm width, 50mm height

300mm width, 75mm height

SAFETY EQUIPMENTS & MISCELLANEOUS

Supply and installation of various sizes of FRLS PVC/ MS conduits ISI make with fish wire, concealed in wall / floor including chipping chasing and allied civil works. Finishing shall be limited to rough plastering only.

19mm dia 1.8mm thick FRLS PVC conduit

25mm dia 1.8mm thick FRLS PVC conduit

32mm dia 1.8mm thick FRLS PVC conduit

19mm dia 1.8mm thick MS conduit

25mm dia 1.8mm thick MS conduit

32mm dia 1.8mm thick MS conduit

Professional charges for getting supply from CEIG, including preparation of drawing, arranging inspection and getting safety certificate. Rate shall be inclusive of all allied expenses. All official & Necessary fees to be paid by vendor.

One lot of MS structural work for various other requirements as required at site. The work shall be painted with one coat of red oxide primer and 2 coats of black enamel. Rate to include all consumables and hardware pertaining to completion of work

Supply installation testing and commissioning of modular metal back box for data with necessary cutting chipping works, closing the same and making the wall/ floor strong, smooth finish.

S & I of Treatment chart framed in Tamil, Hindi and English directly fixed on to the wall with necessary screws etc.

Supplying 11 KV Gloves in wooden box sprayed with dry chalk powder ISI branded.

Supplying and laying class B- 1000mm width X 2.5mm thick 11KV rated ISI marked rubber mats to be laid in front of the panel boards up to the edges. All mats shall be resistant to acid, oil and low temperature and shall be identified with respective class symbol.

First aid box complete medical kit.

Supply and carrying out necessary temporary electrification works at site as and when required by other contractors and ensuring electrical safety at site. Temporary wiring shall be provided with proper plug and sockets and top, wiring properly taped joints if any. ELCB need to provided for incomer for the temporary box ,2set of temporary power industrial sockets to be placed at site (in each set 6 no's of industrial socket with top to be available) /and Led Light fixture with lamp guard to be fixed with minimum lux should be 150 to 200lux. 3 core flexible cable need to be used.

LT Cable trench - Excavation and backfilling of the sand trench along the side of the road. The trench shall be 750mm deep 450mm wide.The bottom shall be filled one layer of 75mm fine river sand and cables shall be laid on top of it. On the laid cables one more layer of 75mm thick river sand , underground utility marking tape (ESB marker red color PVC tape shall be laid on top of it without any gap. The trench shall be backfilled, watered and rammed to suit original level.

EXTERNAL STRUCTURAL GLAZING

Providing and fixing of structural glazing (semi unitised system – all panels fixed) using 15 microns colour anodized Jindal/equivalent aluminium mainframe of size 150x50x2mm with 144x44x2mm GI Infill for intermediate verticals, 72x55x2mm section for horizontals, designed to withstand wind pressure upto 200 kg/sq.m. using necessary aluminium/GI angle cleats with slots for adjusting plumb, fixed to the RCC slabs with M10 expansion fasteners. The glazed panels will be made using 40x42x1.2mm section for subframe, glazed with 6mm thick ST 767 (Blue Ray) / ST 467 (Emerald glaze) reflective heat strengthened glass using double side cross linked polyethylene spacer tape and structural sealant (GE ultraglaze SSG 4000 or Dow sil 795) in such a way as to transfer the dead weight of the glass on to the mainframe so as to avoid undue stress on the structural sealant. The glazed panels after suitable curing in dust free environment will be fixed on to mainframe from the exterior (this system enables easy replacement of glass in future (if any breakage) from the outsideespecially in spandrel areas). The grooves (12 to 16mm) will be closed with weather grade silicone sealant Dow Corning 789 (or) GE silpruf. We will ensure that the whole system uses corrosion resistant hardwares, is totally weather proof, permits necessary thermal expansion/contraction and is able to withstand relevant windloads.

Providing and fixing of structural glazing (semi unitised system – all panels fixed) using 15 microns colour anodized Jindal/equivalent aluminium mainframe of size 72x55x2mm thick section for verticals & horizontals, using necessary aluminium/GI angle cleats with slots for adjusting plumb and fixed with 1.5mm thick aluminium mesh with CNC design perforation stuck on glass using 3M tape, instead of ceramic frit pattern. We will ensure that the whole system uses corrosion resistant hardwares, is totally weather proof, permits necessary thermal expansion/contraction and is able to withstand relevant windloads. (as per your drawing)

Providing and fixing of structural glazing (semi unitised system – all panels fixed) using 15 microns colour anodized Jindal/equivalent aluminium mainframe of size 72x55x2mm thick section for verticals & horizontals, using necessary aluminium/GI angle cleats with slots for adjusting plumb and fixed with 1.5mm thick aluminium sheet with CNC design perforation stuck on glass using 3M tape, instead of ceramic frit pattern. We will ensure that the whole system uses corrosion resistant hardwares, is totally weather proof, permits necessary thermal expansion/contraction and is able to withstand relevant windloads. (as per your drawing)

INTERNAL SLIDING & FIXED PARTITIONS

Supply & Installation of Deko FG single glazed fixed partition suits 10mm thick toughened frosted glass . The panels are supported by Deko natural anodized aluminium ground and ceiling profiles (AGGP) of 26x40mm (H) attached to the floor and suspended false ceiling. On the vertical edges the glass panels are wrapped around with 24x30mm Vertical profiles (AGVP, AGVPA & AGVPT). 1 mmx 7mm Deko Certified proprietary factory finished silicon tape is used for glass to glass joints. The glass to glass joints at the corners to have 90°corner Deko profile and in the perpendicular glass junction (T-junction Profile) A profile is to be used.

Providing & fixing of Sliding Partitions usingextruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material source by NALCO. The Size of profile sections with average minimum thickness of 1.5 mm - 3 Track outer frame -143.7 mm X 47.7 mm,Handle - 70 mm x 30 mm, Interlock- 50 mm x 37mm, Shutter top bottom - 70mm x 27.5 mm. Glass - 8 mm Clear toughened from Saint Gobain. All externally visible surface and the internal visible surfaces will have powder coating finish RAL 9010 of 60 -70 micron thickness, Jotun Make or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. The outer frame should have 90º fabrication joint with frame insert at all 4 corners made of nylon 6.6 material for better resistance to water leakage.The sliding should have 90º fabrication joint with inserted interface, antirattle plastic parts and antilift plastic. Interlocks interface should have EPDM sealing in addtion to wool pile for better resistance to air, water. All Hardware should be Euro Groove Type-1 compatible and handles/ locks should be from top Europians brands. Rollers, woolpile, gaskets - all as per MYWINDOW standards, DOW Corning silicon/ GE/ Wackers with SS 304 screws, etc.

Item same as above- doors

Aluminium Structural Glazing with Glass : Design, Supplyand Installation of Semi-unitised Strutural Glazing by using 10mm Clear Toughned glass to be fixed on the MS Main frame by using Galvanised or Powdercoated MSBrackets which to be weldedon MSMainframe. TheAluminium Mullion and Transom shall be 72*55*2mm Section with Powdercoated or Anodised Finish. The Aluminium Section Shall be ASTM6063T4/T6 Materials to be Procured from either Jindal or Equivalent approvedmake.

Aluminium Structural Glazing with 5mm Alusheet. : Design, Supply and Installation of Semi-unitised StruturalGlazing by using 5mm Powdercoated Perforated Aluminium Sheets to befixed onthe MS Mainframe by using Galvanised or Powdercoated MS Brackets which to be welded on MS Mainframe. The Aluminium Mullion and Transom shall be 72*55*2mm Section with Powder coated or Anodised Finish.

MS Supported Works : Design,Supply and Installation of MS Tube 0f121*61*4mm thick to be used as Purlinsand 60*60*3.2mm Thick to be used asTransom. The Purlins and Transom joined together interms of Wedling or Bolting or asperArchitect's Requirements.

Openable Panels : Extra and above to the Structural Glazing systems. The Hardwares fo the Openable are considered from Alualpha with UKSecurity Heavy duty Frictional Hinges and Stay.

NETWORKING SECTION – A :DATA AND VOICE NETWORK

DATA & VOICE : Copper CAT6 UTP Cables (305Meter)

Supplying, Laying, termination, testing and commissioning in the existing conduit / Duct, Labelling for the identification of Category 6 U/UTP Cable, LSZH slate jacket, 4 pair count, 1000 ft (305 m) length, as complete with all respects complying with relevant standard specification as mentioned in the Technical Specificaiton, as directed by the Engineer-in-charge.

Supplying, termination, testing, commissioning and Fixing, Labelling for the Identification of Category 6 I/O Module and also submit the Testing Report using Fluke Scanner for Data, as complete with all respects complying with relevant standard specification as mentioned in theTechncial Specification, as directed by the Engineer-in-charge.

Supplying, Erection, termination, testing and commissioning in inside the Wall mount / Floored Rack, of Category 6 24 Port Fully loaded Patch panel ,as complete with all respects complying with relevant standard specification as mentioned in the Technical Specification, as directed by the Engineer-in-charge.

Supplying, Erection, termination, testing and commissioning in inside the Wall mount / Floored Rack, of Category 3 50 Port Voice Resource panel ,as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying, Erection, termination, testing and commissioning in inside the Wall mount / Floored Rack, of 100x100 Krone Voice Resource Module ,as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying and testing of Category 6 U/UTP Patch Cable 2M, LSZH, as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.(Rack End)

Supplying and testing of Category 6 U/UTP Patch Cable 2M, LSZH, as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying and testing of Backbox for faceplat as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.(User End)

Face Plate

Supplying, Erection in the existing concealed box / modular of Single Port Faceplate for CAT6 I/O .The rate shall be include nessary accessories like screw, proper labelling with color code, etc ., as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying, Erection in the existing concealed box / modular of Dual Port Faceplate for CAT6 I/O .The rate shall be include nessary accessories like screw, proper labelling with color code, etc ., as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Racks

Enclousers (Switch Rack) Height : 42U H: Width: 800mm Depth:800mm Supply and fixing of powder coated 42U Floored Rack, with necessary Cable Manager, with PDU with 12x 5A, Perforated front and back steel Door with lockable system , Integrated to Frame with Cable entry exit cutout area; Rack should have a Caster wheels with brake. Static load with 750Kg. colour should be Black. • ROHS Compliance and as per specfication and as directed by the Engineer -in-Charge.

ACCESS CONTROL SYSTEM

Supply, intallation, testing and Commissioning of the following system.Access control system complete with necessary hardware, Software etc., as specified for centralized securtiy monitoring.'Access Controllers, each with capacity of 10000 events buffer memory to connecting the item listed below such as card readers, Tripod, Magnetic locks,Boom Barrier, etc. The required master controller with IP shall be included part of the controller line items. The rate shall be inclusive of Power supply unit, enclosure, Protection required for controller against electrical surge , power flucation(Surge protector, power Fuse and Damper Switch) and necessary accessories as required for testing and commissioning of following equipment.

Master controller with IP

2 Card reader controller ( 1set of 1Door )

Emergency break Glass

Egress Swith (Push Button)

Electromagnetic Locks - Single Door - 600 LBS

Magnetic Contact

Cables:

4C 1 Sqmm multistand pvc insulated shielded FRLS armoured cable with drain wire for Cable from electromagnetic lock/Sensor to Controller

8C 1 Sqmm multistand pvc insulated shielded FRLS armoured cable with drain wire for Cable from Reader to Controller

4C Network cable for controller to controller

25 mm dia PVC conduit for the laying of cable with suitable clamp in ceiling with juction box, bend etc (for drop points)

Access management software with time and attendance module as per the detailed specification provided in the Technical spec.

Smart Cards. The card shall be Corporate 1000 Format.

U braket support for fixing of Magnetic latch in all glass door with suitable accessoreise

IP BASED CCTV CAMERA Supply, intallation, testing and Commissioning of the following system 'Note: Please note that, IT Related Equipment for CCTV System shall be provided by IT package .

1080P 2MP IP indoor Dome Camera, 1/3" progressive scan MOS, H.264, 2.8 mm - 10 mm, F1.6, TDN, DWDR, ONVIF Profile S, PoE,133 dB wider dynamic range Audio chip,3x extra optical zoom at 640 x 360 resolution . The rate shall inclusive of support bracket and mounting angles etc (inclusive of Lenz, bracket, indoor housing)

network video recorder (n + 1 -combination) suitable to connect max. 50 camera. Network Video Recording Storage System: Supports 32 channels video recording and 32 channels video playback or relay. Support 4 hard disk direct attached and up to total 32TB disks Space. Total Hard Disk Capacity included - 32TB.The rate shall inclusive of necessary 4CIF, 15 frame /second - 30 days . Continuos recording 8 am to 8 pm and 8 pm to 8 am will be motion based recording

42" diagonal, 1024 x 768 pixels Plasma television with all mounting bracket, connection card wire, remote control etc as per the specification. The bracket shall be provided with adjustable type from wall for better serviceability.(for Continuous monitoring)

SKYLIGHT

4896-A-S-LV9-CM-SPW-MF (48" X 96" aluminium skylight on galvanized steel Vortex ventilated curb mount base, single dome white Skypro Polycarbonate, mill finish frame) Without Curb / MS or Al -Frame

SOLAR PANEL

30KW Solar Panel (Waaree/Canadian)

Supply of GI Roof Top Mounting structures

Supply of 3PH 15KW Solar Inverter (Polycab / Zeversolar / ABB or Equivalent)

Supply AC 55sq.mm Four core Aluminiam Cable Aproxment 150 Mts (Polycab / KEI or Equivalent)

Supply DC 4.0sqmm Copper Cables Aproxment 300Mts (Siechem or Equivalent)

Supply of MC4 Connectors

supply of Array Junction Box.

Supply of Fitting Accessories, Pipe, other accessories & consumables.

Installation & Commissioning

FIRE FIGHTING DOWNCOMERS SYSTEM

Supply and installation of Cast Iron Butterfly isolation valve (PN:16) as per specification with necessary flanges, nut, bolts & washers, painting, etc. complete as required

Supplying and installation of Cast Iron Swing Check Valves (PN:16) as per specifications including making flanged joints by providing with necessary flanges, nut, bolts & washers, painting, etc. complete as required .100 NB

Supplying and installation of Brass made, chrome finished Ball valves with fittings of screwed end / flange end type as per specification with necessary accessories, painting, etc. complete as required.

Under Ground piping - Supply, erection, testing and commissioning of Mild Steel (MS) pipes conforming to IS 1239 for 150NB & below with necessary joints and fittings (heavy class forged fittings of IS standards) including cutting the pipes to correct length, providing and welding flanges to pipe, etc as per specifications of the following diameters. Rates shall be inclusive of 10% radiograph test complete as per specifications of the following diameters and all necessary supports.

150 NB - Class C

100 NB - Class C

80 NB - Class C

150 NB - Class C

100 NB - Class C

80 NB - Class C

25 NB - Class C

Supply and installation of Hose Tray consists of 2 Nos RRL Type-A hoses of 63mm Dia x 15 meters long with heavy quality gun metal male coupling as per IS: 903 combined wwith 1 No of branch pipe with nozzle.

Supply & Installation of drum type wall mounting hose reels, swiveling 180o consisting of 25 mm Dia hose, 19mm bore, 30 meters length rubber hose pipe with 6 mm Dia. gun metal / bronze shut of type jet nozzle & cut-off valve on the inlet including making connection to the wet riser, by drilling welding, fixing the hose reel to the wall by providing necessary anchor fasteners/ expansion bolts, grouting the same with cement mortar, painting all complete as per drawings and specifications.

Supply & installation of Fire Brigade inlet connection with provision for Four male instantaneous coupling fabricated out of 150 mm Dia. approved make heavy class MS pipe for fire fighting system including necessary fittings to the fire storage tank, ring mains of hydrant system. Rate shall inclusive of 150NB cast iron butterfly valve & single plate slim check valve, painting the same with 2 coats of red enamel paint over a coat of Zinc Chromate primer all complete as per drawings and specifications.

Supply and wrapping of 4mm thick Anti-corrosive Coating & Wrapping Materials manufactured as per IS: 10221 for underground Pipes as per specification

Excavation of earth and refilling with river sand or quarry dust (should not damage the wrapping material), 250 mm above and below of pipe then with earth compaction upto formed ground level.

Soft Sand

Supply and erection of steel supports like MS plate, angles, channels, etc

FIRE FIGHTING : PORTABLE FIRE EXTINGUISHERS: Supply, installation, testing and commissioning of following types of extinguisher with provision of wall bracket (fixed with anchor fastener). All extinguishers should have the in-built pressure gauge.

Carbon-di- oxide type fire extinguishers 3 Kg Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & horn, wall mounting bracket etc. complete, confirming to IS: 2878.

ABC (Powder Type) Fire Extinguisher. ABC (Powder Type) Fire Extinguisher of 4 kgs capacity, In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:1349-1993.

Supplying and installing at approved location approved make fire buckets (4 Nos) of 24 gauge galvanized steel sheet, standard 9 liter capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold. Cost shall be inclusive of providing MS stand duly painted over a coat of primer.

Supply and Erection of electrically driven pumpset. Motor SPDP type, 2900 RPM, 420 V,50 cycle, 3 phase Class 'F" insulation, IP - 55 protection, 10 HP starting on DOL. The Pump shall be shall be cast iron casing, bronze impeller, steel shaft. with common base frame capable of discharging 450LPM at 35M head. Pump to be installed at Terrace.

SUPPLY and LAYING CABLES / EARTHING:(Incl Termination)

3.0 C x 6 Sq.mm Cu. Armoured Cable

2 C x 1.5 Sq.mm Copper armoured Cable

Supply and Erection of Cable Tray 100 mm wide (In side the FWPH).

Earthing of the Electrical Motor and panels of booster pumps with 8 swg copper wire.

Supply and fixing of Pressure Switch weather proof RT type with SPDT for Annunciations.

Supply and fixing of 150 mm dia dial Pressure gauge, Glycerine filled installed with SS syphon tube. .

Supply and fixing of :Cast iron Sluice valve including making necessary flanged joints by providing necessary nuts, bolts, Neoprene gaskets, etc. all complete 150 mm dia, PN 1.0 rating

Supply, Installation, Testing and Commissioning of ANALOG ADDRESSABLE FIRE ALARM SYSTEM

Addressable Intelligent TWO loop Standalone Fire Alarm Panel with 4 Hours battery back up in Normal Condition and 20 Minutes Battery backup in alarm condition

Analog Addressable Smoke cum Heat Detector

Addressable Intelligent Heat Detector

Addressable Manual Break Glass type call point

Sounder cum strobe

Addressable Relay modules for Access control & Base Builder Integration

Addressable Control modules for Sounder

Addressable input modules for Sprinkler flow switch & Base Builder Integration

Short Circuit Isolator

Supply and Surface laying of 2 core x 1.5 sq.mm Red colour Copper, PVC Insulated, FRLS, armoured cable

24VDC Power supply unit for activating sounders

DISMANTLING AND DEMOLISHING

Credit to department towards dismantled materials taken by the contractor from dismantling the existing CFI building including the cost of dismantling, salvage value of material available from dismantling and cost of disposal of unservicable materials The plinth area of existing CFI building is 1600 sqm (Approximately). The building designed as workshop building at an average height of 15m (Approximately). The roof is curved shape RCC roof slab covered with AC sheet roofing .The existing flooring has ceramic glazed industrial tile flooring. The windows are having glazed windows made of teak wood frames The Annex building roofing is galvalume sheets roofing with steel tubular truss work. All debris obtained from dismantling after taking away the salvage materials shall be removed from the site and disposed off outside the IITM Campus.(The agencies shall inspect the existing workshop(Cfi) building and assess the cost of dismantling, salvage value of material available from dismantling including cost of disposal of unservicable materials and accordingly quote the rates as an over all percentage for all Civil works including dismantling). Demolition for Existing Building

P Subramani and Co

SAKTHIKANNA CONSTRUCTIONS PVT LTD