Special repair of PHC Ranila in Charkhi Dadri Distt. (Reinvite)

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm. layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Dismantling Brick Wrok, Tile Masonry or Tile Lining and Tile Terracing (b) In cement (HSR 8.5b)

Dismantling Roofing (a) first class mud roofing (HSR 8.8 a)

Terracing consistiong of tiles 22.86 cm X 11.43 cm X 3.81 cm, laid over 87.50 mm mud filling, on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles over a polythene film of 100 micron (0.1 mm) thickness with 25 mm thick layer of fine sand, above and below the polythene film, laid on top of R.C.C. slab, including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.13)

Cement concrete 1:8:6 with stone aggregate 40 mm nominal size in first storey upto 5 metres above plinth level. (HSR 10.46)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)]

Damp proof course 75 mm thick of cement concrete 1:2:4 using stone aggregate with 2 coats of bitumen 20/30 penetration, at 1.65 Kg. per sqm. Laid hot and sanded. (HSR 10.113)

First calss brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & RAK (HSR 14.89)

Providing and fixing 1st auality ceramic glazed wall tiles confirming to I.S 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except gurgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in whte cement mixed with pigment of matching shades complete. (HSR 14.92 b)

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):--(a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (HSR 17.93,ii) 30 mm thick

Providing and fixing aluminium work for doors windows, ventilators and parti-tions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS, 733 and IS: 1285 fixed with rawlplugs and screws or with fixing clclips or with expansion hold fasterners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprence felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P. brass / stainless steel screws, all complete (HSR 17.95)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete. (a) Pre-laminated particle board with decorative lamination on one side & balancing lamination on both side (HSR 17.97 a)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required embedding in floors and cover plates with brass pivot and single piece M.S.sheet outer box. (HSR 17.99,a) (a) With Stainless Steel cover plate

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including Straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths /storeys/ basements etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement). (HSR 18.22).

Earth work non plastic or Tibba Sand under floors taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. (For any Lead & Lift). [NS].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge), INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I. ‘P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2 b i)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREIOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. cistern complete (as approved by the Engineer-in-charge) (i) White (HSR 30.8)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid.(i) White plastic seat (Solid). [HSR 30.13 (i)].

PPROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE STALL URINALS 1150 MM HIGH IN VITREIOUS CHINAWARE WITH ONE NO. 10 LITRES CAPACITY C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE COMPLETE as fully described in item no. 30.29 above. (HSR 30.31 i)

Providing and fixing 25 mm thick marble partition for different type of urinals. Small size 680mm x 330 mm Single Color(HSR 30.40 b ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LAVATORY SUITES (WITH FULL ANTI SPLASH RIM IN VITREIOUS CHINAWARE and all other necessary fittings as fully described in item no.30.41 above. White Size 510 mm X 400 mm with one no tap(HSR 30.42 i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE. (HSR 30.45)

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. [HSR 30.53 (a)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (d) CP Brass two swivel towel rail 400 mm long (HSR 30.68 d)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 a i)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

(c) Bib cock

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (i) Stop cock male and female end

(ii) Concealed stop cock with flange

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) two way (HSR 30.78 b)

Providing and fixing in position best Indian make flexible tube connection. (a) aluminium (iii) 15mm x 450 mm. [HSR 30.82 (a) (iii)].

Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84) (a) 100 mm internal diameter.

Cutting chase in brick wall in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition. [HSR 30.95 (a)]. (a) Size 75 mm x 75 mm.