ADDN ALTN TO AIRMEN LIVING IN ACCN AT AF STN BIKANER

Amount

Demolition of concrete of any description and in any position not otherwise specifically provided, and removal of debris outside MOD land ,complete all as specified and as directed.

Dismantling of bricks(laid flat or on edge) or brick tiles in roof, floors, channels kerbs,aprons etc (each layes) laid bedded and pointed in any mortar, complete all as specified and as directed.

M&L for APP based modified pre fabricated five layer 3 mm thick and weighing not less than 3.0 Kg/Sqm water proofing membrane reinforced with polyester non woven fabric mat with 150 gm/Sqm black finished with compatible primer conforming to IS 3488 @ 0.30 Lit/ Sqm and bonding material 85/25 bitumen 1.2 Kg/Sqm before laying membrane laid by torch application side overlap of 75 mm and over lap of 100 mm longtitudinally, At the junction of roof and parapet wall a grove of 20 x 20 mm shall be made at the ht of 100 mm and membrane shall be inserted and sealed with bituminious mastic joints/overlap shall ve saled with hot bitumen 85/25. Two coat of water proofing bituminious aluminium paint on top of APP membrane shall be applied , complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of grooves with cement mortsr 1:3, complete all as specified and as directed.

M & L for 15 mm thick plaster in CM 1:4 over concrete surfaces of roofs finished even and smooth using extra cement with WPC @ 3% by weight of cement, complete all as specified and as directed. Note :- WPC will be measuredpaid seperately.

M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry with grey cement and no pigments in floors, and cut and polished including 15mm thick screed bed in CM (1:6) complete. complete all as specified .

Material and labour for cement concrete PCC (1:2:4) type B1 (20mm graded crushed stonne aggregate) as in roof padding complete all as specified and directed

Demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified & directed.

M&L for brick work with old size sub class "B" bricks straight or curved on plan exc 6 m mean radius and built in cement mortar(1:6), complete all as specified and as directed.

M&L for Anti termite treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified & directed.

M&L for anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified & directed.

M&L for post construction treatment ATT in voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified & directed.

Dismantling stone and tiles of any description or thickness in floor aprons etc, complete all as specified and as directed.

M&L for Machine cut kota stone(similar shade of all pieces) slab flooring 20-25mm thick over 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed

M&L for Kota stone(similar shade of all pieces) slab 20-25mm thick in riser and tread of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 10mm thick rendering in CM(1:4) including rounding of edges of stone rubbing and polishing complete complete all as specifdied & directed

M & L for machine cut Granite slab 15 mm thick for steps, pillars, window cills, cooking plateforms and like and incl 10mm thick (avg thickness) cement mortar 1:4 screeding and setting coat in cement morter(1:2), 3mm thick, set and jointed with white/coloured cement to match the shade of slab incl cutting, waste, rubbing and polshing etc complete all as specified and as directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish all as spfd.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removal complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7-8 mm thick, (square/rectangular) area of each tile exc. 0.11 but n.exc. 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in CM(1:6) , complete all as specified and as directed.

M & L for joint free glazed coloured ceramic coloured tiles of 350mm x 250mm x 7mm /450X 350X 7mm thick on vertical surface of walls set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles, laid over and including 10mm thick rendering in CM(1:4), all as specified and directed by engr-in charge.

Taking down chowkhats with shutter without taking off shutters from the frames (area n. exc. 1.50 sqm each) incl making good the disturbed surfaces complete all as specified & directed.

Supplying & fixing in opening solid PVC door frame of size 50mm x 47mm made out 5mm plain colour PVC sheets re-inforced with MS tube Square tube, suppling & fixing in opening complete all as specified & directed

M&L factory made solid panel pvc door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail . paneling of plain colour PVC sheets to be filted in MS frame welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with the solvent cement complete all as spd.

Supply and fixing Mild steel butt hinges medium weight , clod rolled, 75mm, ISI marked, complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 100 mm complete all as specified & directed.

Supply and fixing aluminium fabricated type extruded handles of size 100mm complete all as specified & directed.

S&F in repair Steel window 1.25mm thick box type ERW hollow P section of each frame size 60mmx25mm double rebated comprises of glazed & gaused Skelton shutter ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 100mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) 10mm square Guard bar @ 10 cm c/c. (vi) Two coat of Synthetcitc enamel paint over one coat of primer (vii) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in glazed / gazed skelton shutter of window (viii) 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane fixed in glaxed / gazed skelton shutter of window. (ix) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.

Taking down chowkhats with shutter without taking off shutters from the frames (area exc. 1.50 sqm but n. exc. 4.00 sqm each) incl making good the disturbed surfaces complete all as specified & directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and removing to or from store as required complete all as specified.

Material & Labour for Factory made pressed steel frames 1.25 mm thick ms sheet, for doors of size 125 x 60 mm for doors with one or more rebate incl necessary fixing lugs, hinges, lock, strike plates of 50 x 3mm welded with frame and making arrangement for fixing of door spring etc complete all as specified.

Supply and fixing factory made plain, framed, Plain framed, panelled shutter (two panel) 35 mm thick of 2nd class hardwood rail and style with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated incl one coat of pink primer complete all as specified & directed.

Supply and fixing factory made glazed and gauged skeleton shutters 35mm thick, 2nd class hard wood 'Hollock' open rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc incl priming coat. The size of member of shutters as spfd in SSR Part-1 Section 8 clause 8.24 (a) incl kiln seasoned and chemically pressure treated, complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 200 mm complete all as specified & directed.

Supplu and fixing in repair, barrel tower bolts aluminium anodised extruded section of size 200 mm ,complete all as specified & directed.

Supply and fixing aluminium fabricated type extruded handles of size 150mm complete all as specified & directed.

Supplu and fixing in repair, aluminium fabricated type extruded handles of size 150 mm ,complete all as specified & directed.

Supply and fixing 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

Supply and fixing in repair, 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

Supply and fixing Galvanised mild steel wire cloth, in new doors and windows 0.56mm nominal dia of wire and avrg widh of aperature 1.18mm incl fixing to wooden/steel frames with tinned tacks or galvanised wire or wooden bead complete all as specified & directed.

Supply and fixing in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avrg widh of aperature 1.18mm incl fixing to wooden/steel frames with tinned tacks or galvanised wire or wooden bead complete all as specified & directed.

Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as directed.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or with clip in squares n.ex.c. 0.50sqm in each pane complete as specified and as directed.

All as per item no 42.00 above but 4mm thick ordinary sheet glass exc 0.5sqm in each pane.

Material and Labour for preparation of new surfaces of wood & wood based surface of any description not otherwise described, over 10 cm width & girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new steel & steel based surface of any description not otherwise described, over 10 cm width & girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) incl for angle iron,fencing post,Rolling shutter etc. complete all as specified & directed.

M&L preparation of old painted wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified & directed.

Material & Labour for Plain Cement concrete type B-0 (1:2:4) (using 12.5 mm graded crushed stone aggregate) as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in presserd steel frame and the like finished fair and even incl necessary form work complete all as specified & directed.

Taking up or down 15 mm dia steel tubing and connection and removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified and directed.

Supply and fixing 15mm bore tubes "medium grade" galvanized with and incl all fittings complete to walls and ceiling with necessary clamps or laid in floors complete all as specified & directed.

Supply and fixing 20mm bore tubes "medium grade" galvanized with and incl all fittings complete to walls and ceiling with necessary clamps or laid in floors complete all as spd & directed.

Supply and fixing in repairs long body Bib taps,chromium plated cast copper alloy with quarter turn, screwed down, screwed for iron pipe or for brass ferrule and fixed, suitable for 15mm bore pipe complete all as specified and directed.

Cutting chases, pining in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chases for concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all asdirected.

Supply and fixing in repairs fancy type angle stop valve, chromium plated,screwed down, high pressure with quarter turns, screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Supply & fixing in repair PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Supply and fixing as in repair vitreous china squatting pan "Orissa" pattern size 580 x 440mm, white, with integral footrest (excluding flushing cistern) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor, set with cement concrete, fixed as in repairs complete all as specified and directed.

Supply and fixing as in repair PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including PVC connection and 32mm dia PVC bend for required squat pattern etc, set with concrete and making good to floor, fixed as in repairs complete all as specified & directed.

Supply & fixing as in repair vitreous china wash hand basin, white flat back, size 300mm x 450mm including pillar tap 15mm dia chromium plated with capstan head with long screwed shanks and fly nuts, and brass chromium plated waste coupling 32mm dia complete all as specified & directed.

S&F as in repairs Chromium plated shower roses 125 mm size fixed with swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

S&F as in repairs 100 mm dia mild steel chromium plated grating with or without waste pipe hole as per requirement complete all as specified and directed.

S&F in repair tubular towel Rail 20 mm dia, 600mm long, of brass chromium plated complete all as specified and directed.

S&F in repair curtain road 30mm dia of brass chromium plated complete all as spd and directed

S&F in repair soap dish vitreous China white, approximate size 160x 160x90mm , any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

M&L for gunniting work to RCC work in column, flooring, side walls, beam, slab, etc by carefully chipping, removing exhisting loosel/damaged concrete cover etc, and cleaning all exhisting reinforcement bars with wire brush and applying alkaline rust converter primer on exhisting rebar and allowing it to react with rust for 06 hrs and form corrision resistant layer, then applying Zinc rich anti-corrisive protective coating on reinforcement bars as per manufactures instructions, and fixing wire mesh fabric size 50mmX 50 mm with 3mm dia with exhisting bars( as required), then applying plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 25 mm and making the surface even and fair and applying 15mm thick rendering in CM(1:4) on surfaces, finishing the surfaces even and smooth, without using extra cement including necessary form work as required etc, and complete all as directed by enggr-in-charge. Note :- wire mesh shall be measured and paid as supply only.

Supply only hard drawn MS steel wiremesh 50mm X 50mm with 3mm dia wire with Heavy duty nails, Fixing the mesh on the ceiling before gunniting work.

Material and labour for repairing of RCC projection, chajjas, facia, bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion of RCC upto 8m height and in any sitution with necessary support, formwork and welding of reinforcement(if required) with wire mesh and dubbing/ filling 1st coat of 20 to 25mm thick in cement mortar (1:3) finished rough and finishing coat of 10mm thick in cement mortar (1:3) finished even and smooth without using extra cement after applying cement slurry @ 3.00 Kg/Sqm and applying two coats of exterior emulsion paint over and including a cot of primer, complete all as specified and directed. Note : (i) Unit rate of this items includes the cost of scaffolding, form work, necessary water proffing agent etc and nothing extra shall be paid on account of variation if heights. (ii) The measurement of finished plaster of 2nd coat provided on surface in sqm shall be the mode of measurement aganst this item. (iii) wire mesh shall be measured and paid sepertly as supply only.

S&F PBI Sheet 1mm thick shutter with box type steel frame for built in up steel cupboard,almirah etc incl applying two coats of synthetic enamel paint over a coat of red oxide primer on both surfaces and locking arrangement with 4 lever lock complete and including taking down chowkhats with shutter all as specified and directed by the Engr - in Charge.

Dismantling boarding any description fixed in any position with screws, complete all as specified and as directed.

Supply and fixing 18/19mm thick prelaminated particle board interior grade prelaminated both side with decorative choice lamination & other side balancing white lamination fixed with screws complete all as spd and directed by Engr-in-Charge.

Taking down cement plaster any description on brick/concrete surfaces etc including raking out joints hacking for key, scrubing down with water etc complete all as specified and as directed.

Material and labour rendering 15 mm in cement mortar(1:6) on fair faces of brick or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm in cement mortar(1:4) on fair faces of brick / concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm in cement mortar(1:3) on fair faces of brick /concrete surface of ceilling and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper (white or tinted) over and including a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of ceilling / chajja or similar suspended work and applying two coats of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls including all cornices, pilasters etc and applying two coats of acrylic exterior emulsion apex paint in camouflage pattern of approved tint / shade(s) over and including a coat of water based primer complete all as specified and directed.

Materail and Labour for complete removal of exhisting treatment and preparation of plastered or unplastered old surfaces of walls and two coats of oil bound distemper over and including a coat of primer, all as specified and as directed by Engr-in-Charge.

Materail and Labour for complete removal of exhisting treatment and preparation of plastered or unplastered old surfaces of ceiling and two coat of white wash on ceiling all as specified and as directed by Engr-in-Charge.

M&L for 3 mm thick , wall care putty on walls, in two coat and after complete drying rubbing gently with waterproof emery paper greater than 500, and complete all as specified and as directed.

M&L for 3 mm thick , wall care putty on ceiling, in two coat and after complete drying rubbing gently with waterproof emery paper greater than 500, and complete all as specified and as directed.

Material and labour for complete removal of existing/old treatment and preparation of surfaces using necessary filling compound of putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior emulsion paint (Apex from asian paint or equivalent in list of makes) over and including a coat of primer , on wall at upto 7.5 m height complete all as specified and directed by Engineer - in- charge.

Demolition of plain cement concrete in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified & directed.

Material & Labour for 75mm thick cement concrete type D-2,1:4:8 (40mm graded crushed stone aggregate) as in sub base concrete all as specified & directed.

M&L for PCC (1:3:6) type C-2, using 40mm graded stone aggregate as in plinth protection 75mm thick laid in bays including all necessary form work, finishing exposed edges fair and providing 10 mm wide joints throughout the thickness of plinth protections duly filled with matic filling(one part of hot bitumen 85/25 and three parts of sand) and surfaces finished even & smooth without using extra cement complete all as specified .

S&F Harrison rails in repair mild steel, anodised aluminium with fixing brackets, stops, rollers etc.

Dismantling wrought iron or mild steel work of any description not other wise or as specified

M&L for steel work in tubular pipes as in vertical surfaces including special shaped washer such as column complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240, complete all as specified and as directed.

M&L for rolled section as in main and cross beam , hip and jack rafters; purlins where connected to common rafters and running rails andm guides for sliding doors fixed with angle cleats or other connecting plates in Fe 290 Gde E-165 complete all as specified and as directed.

S&F for plates (plain or chequred ) channels ,square cut or notched (ordinary and counter sunk) forming holes , without any attachement in Fe 290 Gde E-165 complete all as specified.

M&L Mild steel screw bolt (machine made) dia 11 to 15 mm with hexagonal or square head at one end and screwed the other or screewd both ends each screwed end to be fitted with washers and one hexagonal nut length of bolt exc 5 cm but n. exc 10 cm long complete all as specified

Dismantling of plane or corrugated galvalum, steel sheeting, any gauge, thickness including Nainital or similar pattern roof covring, complete all as sprcified and as directed.

S&F 2mm, Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type in roof, wall etc complete all as specified & Directed

S&F as in door beading 40mm x 6mm with metallic body fixed to bottom rail of door with screws and washers of suitable size complete all as specified and directed.

S&F as in repairs 110mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall including clamps as required, complete all as specified.

S&F as 110mm dia PVC (SWR) bend with rubber ring joints fixed as required complete all as specified.

S&F in repair, 75mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall including clamps as required, complete all as specified.

S&F 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) bend with rubber ring joints fixed as required complete all as specified.

Material & Labour Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains;hand made sliding bolts; clamps;hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified.

Taking down and Easing of door shutter of any size for smooth opening/closing by tightening of butt hinges in position including changing of unserviceable existing butt hinges, adjustment of butt hinges in position, adjustment of existing iron mongery, welding etc. and re-fixing in same opening complete all as specified and directed.

Taking down and Adjusting / repairing of steel window shutters for smooth opening/closing including greasing, welding and adjustment of projecting type friction hinges in any position make fully functioning complete all as specified and directed.

Material and labour for grinding and polishing of existing kota stone flooring, with machine and filling joints with white cement and pigment to match the existing colour complete all as spd and directed

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,M&l for buffing, polishing and making curvature (where ever required) and fitting the same with ecessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as per existing at site including making good the disturbed surfaces to match with the existing finishes,complete all as specified and as directed.

M & L for Point wiring on concealed conduit with 1.5 Sq mm copper conductor single core PVC insulated unsheathed 1100 V grade FRLSH multistranded drawn into and including rigid PVC conduit with accessories of suitable dia medium grade concealed in walls/floors and pressed steel terminal boxes MS, duly painted with red oxide metal primer including fixing/grouting sunken/ surface as per site requirement covered with 3 mm thick laminated sheet including one running up of 1.5 Sq mm copper conductor PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified.

One light point controlled by one, one way switch 6 A, SP

One ceiling fan/exhaust fan point controlled by one, one way switch

One light point controlled by two nos, 2-way, 6 Amps switch.

One 3 point 6 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 6 Amps switch socket outlet point controlled by one switch on independent board.

All as per item No 104 (here-in-before) but using 4.0 Sq mm single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade FRLSH for 6/16 Amps switch socket combination point including running of 4.0 Sq mm copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

S & F Switch piano type single pole one way flush type 6 Amps capacity 230 volts.

S&F of Switch piano type, single pole, two way, 230 volts, complete all as specified and directed.

S&F of Socket, two-in-one, 5 pin, 6 Amp, 230 volts, complete all as specified and directed.

S & Fixing of switch socket combination 2 in 1 multipurpose 2/3 pin 6 Amps flush type complete all as specified.

S & F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified

S & F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified.

S&F of Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size,complete all as specified and as directed.

Supply and fix stepped type electronic ceiling fan regulator AC 230 Volts suitable for 1200 / 1400 mm sweep complete all as specified.

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed.

Supply and laying sub main wiring complete with 05 runs ( 3 nos for three phase, Neutral & Earthing ) of single core 10 sqmm fire retardant low smoke (FRLSH) PVC insulated copper conductor cable multistranded and sheathed LT 1100 V grade drawn through and including concealed rigid PVC conduit of suitable dia ISI marked and accessories surface fixed on wall /floor etc all as specified. Note:- 05 runs of cable 01 metre 01 run of PVC conduit shall be measured as one unit for measurement purposes.

M & L for Submain wiring with two single core 10 Sq mm PVC insulated unsheathed copper conductor multistranded 1100 Volts grade, FRLSH drawn in and including concealed rigid PVC conduit of suitable dia, conduit fittings and accessories concealed in wall/floor with one run of 10 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note 1: Two runs of 10 Sqmm cable, one run of 10 Sqmm earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

M & L for Submain wiring with two single core 4.0 Sq mm PVC insulated unsheathed copper conductor multistranded 1100 Volts grade , FRLSH drawn in and including concealed rigid PVC conduit of suitable dia, conduit fittings and accessories concealed in wall/floor with one run of 4.0 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note 1: Two runs of 4.0 Sqmm cable, one run of 4.0 Sqmm earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

Supply and fixing Vertical TPN DB double door, IP 45 protection with powder coated enclosure 8 way insulated busbar assembly suitable for fixing MCCB 4 pole, 415 V, 125A, 16 kA - 01 No complete all as specified and directed. Note: MCCB and MCB shall be of same make as of DB.

Supply and fixing TPN DB double door, IP 45 protection with powder coated enclosure 6 way insulated bus bar complete all as specified and directed. Note: MCB shall be of same make as of DB.

Supply and fixing sheet Metal enclosure double door type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete all as specified and as directed

Supply and fixing MCCB 3 Pole, 415 V, fixed type, 125A Amps with breaking capacity 16 KA, complete all as specified and as directed

Supply and fixing MCB, 4 Pole, 63Amp, 415V 10KA 'C' curve, complete with connection testing and commissioning.

Supply and fixing MCB SPN 40-63 Amps , 240 volt, 10 KA, complete all as specified and as directed

Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep, metal body with louver including making of hole to the wall and making good the disturbed surface complete.

Supply and fixing Energy saving and environmental friendly long life 35W LED bldg security light having IP66 protection complete with all accessories incl three run of 1.5 Sqmm Copper conductor cable from security light to ceiling rose complete.

Supply and fixing in repair GI pipe bracket made of 40 mm bore light grade pipe made to shape of overall length of 1.2 mtr for fixing of security light fitting including MS clamps , nuts & bolts of required size complete all as directed.

M & L for Earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth lead 4mm dia, by means of nuts, bolts, check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe light grade 15mm bore from earth elelctrode to DBs/main switch incl provn of concrete pit in PCC , GI pipe light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr complete all as specified and directed.

JAMUNA CONSTRUCTION AND GENERAL ORDER SUPPLIER (BID ID -3307033)

HINGLAZ ENTERPRISES (BID ID -3307215)

SHREE GURU NANAK CONSTRUCTION COMPANY (BID ID -3308589)

M/S BIKANER CHEMICAL LABORATORIES (BID ID -3312878)

Durga Construction Company (BID ID -3307395)