PROVN OF ADDN ALTN TO BUILDINGS AT YOGENDER VIHAR UNDER GE SOUTH DELHI CANTT10

Amount

M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed. (vii) Sprinkle sand cover over surface to receive new

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. Superficial area of member to be considered for measurement

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed including M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete as directed at site Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

Dismantling Bricks (laid flat or on edge) or brick tiles in floors, roof, channels, kerbs, aprons, etc. (each layer all as specified and directed.

Demolition Mud in roofs, any thickness, including plastering and lapping (whether full thickness removed or only a part thereof) all as specified and directed.

Removing soil excavated material exc. 1.5Km but n exc 5km and depositing where directed at above the starting point all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (using 12.5mm graded stone aggregate) on roof padding surface finished even and smooth without using extra cement complete all as specified & directed.

M & L for screed bed 10 mm thick (average) plaster on concrete surfaces in CM (1:3) on roof, mixed with water proofing compound and finishing the surface even and smooth without using extra cement all as specified and directed (Water proofing compound shall be measured and paid seperately).

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints.

M&L for preparation of new surface of APP membrane and applying two coats of aluminium paint at surfaces of any description, over 10cm in width or girth,not otherwise described

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specially provided for.

M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed..

Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons etc laid bedded and pointed in any morter complete all as specified and directed

M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps,jambs,pillars, window-cills, cooking platforms with necessary hole for gas pipe where ever required and likes on cement mortar bedding of 20 mm in CM 1:4 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and directed.

M&L for machine cut kota stone slab flooring, and (one Pieces) as in steps (Treads), 20-25mm thick over cement screed bed 20mm thick with CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Ditto but of riser of step, dado skirting etc complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps cooking platefom,and other similar situations complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar (1:6) complete all as specified and as directed.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed. Make: Somany/Orient/Kazaria or equivalent

S & F for glazed Ceramic tiles 9 to 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm ( size 600 mm x 600 mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for 25mm th PCC 1:2:4 type B-1 using 20mm graded stone aggregate as level course under floor tiling etc complete all as specified and directed.

M&L for 15mm thick screed bed or bedding in CM 1:6 complete all as specified and directed

All as per item No 26 here in before but as in skirting laid over and including 10mm thick backing coat of cement mortar (1:4), complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

Supply plastic water closet seat cover white closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified and directed.

Supply only PVC low level white flushing cistern valveless symphonic action type 10 lts capacity IS marked with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC,(ISI Marked) complete all as specified. Make-Cera/parryware/hindustan all as specified .

S & F in repairs 15 mm dia 600mm long PVC connections with brass check nut complete all as specified and directed. Make Polytuff/symet or equivalent

S&F in repair vitreous China wash hand basin (pedestal) white of size 550X400mm excluding taps, waste chain and plug and porcelain stopper and waste pipe & waste coupling including all necessary fitting and fixtures complete all as specified and directed.

S&F in repairs Brass chromium plated mode 2 in 1 WHB mixture 15mm dia including necessary fittings model Quarter half turn (SOLO) of as complete all as specified & directed.

S&F in repairs brass chromium plated mode 3 in 1 wall mixture 15mm dia including necessary fittings model Quarter half turn (SOLO) as all specified and as directed.

S&F in repairs Brass chromium plated mode 2 in 1 sink mixture 15mm dia including necessary fittings model Quarter half turn (SOLO) of as complete all as specified & directed.

S&F in repairs chromium plated soap dish fancy type all directed. complete all as directed (Make-Marc/Kholar) all as specified .

S & F in repairs brass chromium plated tubular towel rail, 20 mm dia D type , 60 cm long between flanges all as specified and directed.

S&F chromium plated towel ring complete all as specified and directed.

S & F chromium plated toilet paper holder with flat recessed type stainless complete all as specified and as directed.

S&F elegent mirror PVC cabinet (PTMT alloy) complete all as specified and directed.

S&F in repair PVC waste pipe 32/40 mm bore, 65 cm long for sink etc complete all as specified and directed.

S & F in repairs Chromium plated brass overhead shower rose 125mm with arm complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs bib taps 15 mm bore chromium plated brass, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repairs angle valve, fancy type, chromium plated brass, 15mm, complete all as specified and directed.

S&F 2-in-1 bib tab fancy type, chromium plated brass, 15mm, complete all as specified and directed.

S & F in repairs Glass Corner Shelf 6mm thick including CP railing radius 250mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Glass shelf assembly 5.5mm thick, 600mm long 120mm wide with cp railing complete all as specified and directed.

S&F stainless steel plate rack overall size (31X30X10 inch) fixed with steel screws with wooden gutties and thickness should not be less than 1mm complete all as specified and as directed.

S&F in repair stainless steel sink with drainage board made out of 1mm thick sheet for kitchen with plug, washers, waste pipe, waste coupling incl fixing cast iron cantilever bracket connecting union over all size 495x420mm with bowl size410x330x160mm complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing. complete all as specified and as directed.

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing. complete all as specified and as directed.

M&L for Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

S&F 20mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 25mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 40 mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings for WHB on walls/ceiling or laying in floors complete all as specified and directed

S&F 20mm outer dia CPVC Union complete all as specified and directed.

S&F 25mm outer dia CPVC Union complete all as specified and directed.

S&F 40mm outer dia CPVC Union complete all as specified and directed.

S&F 40mm outer dia CPVC Tank Adaptor complete all as specified and directed.

S&F 25mm outer dia CPVC Tank Adaptor complete all as specified and directed.

S&F 20mm outer dia CPVC Tank Adaptor complete all as specified and directed.

S&F 25mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC Brass Elbow complete all as specified and directed.

S&F 20mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 25mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 20mm outer dia CPVC Brass Tee complete all as specified and directed

S&F Brass reducer 40mm x 25mm outer dia CPVC complete all as specified and directed

M&L for rotational moulded polyethylene water storage tanks white colour 500 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT float valve, lid tank cover for polyethylene and polyethylene ball including taking out existing unserviceable overhead tank of any description including fitting and fixtures complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50 m in depth for manholes & sewage lines and getting out in soft/loose soil.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm.

Removal of excavated surplus soil to a distance not exc 50 metre at a level not exc 1.5m above or below the starting point. complete all as specified and directed.

S & F DWCPE pipe, SN8, 170 mm diameter pipes including coupler and rubber ring incl testing,properly jointing and laying in trenches complete all as specified and directed. all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 100mm bore including packing under and haunching against sides of pipes after they are laid and tested. complete all as specified and directed.

Demolition and breaking up rain water pipes (CI,AC etc) set in any cement mortar of any diameter incl bends complete all as specified and directed.

S/F PVC (SWR) 110mm pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, soil, waste, vent pipe in any length with or without ears including clamp as rqd ,110mm bore complete all as specified and directed.

S/F PVC (SWR) 75mm pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, soil, waste, vent pipe in any length with or without ears 75 mm bore complete all as specified and directed.

S&F for PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F for PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F for 110 PVC (SWR) Tee with door plate complete all as specified and as directed.

S&F for 75 mm PVC (SWR) Tee with door plate complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in solvent cement concrete complete all as specified and as directed.

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc incl cleaning or re-fixing or removal to store(measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamp, of 110 mm dia complete all as specified and directed.

S&F for PVC (SWR) bends any radius 110mm dia bore complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete all as specified and directed.

M&L for outdoor tile parking tiles size 300 x 300 mm conforming to IS 15622:2017 including 20mm screed bed all as specified and as directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L rendering 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L rendering 10mm thick in cement mortar 1: 6 and top layer 5mm thick in cement mortar 1: 4 mixing water proofing compound on faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L Rendering 5mm thick in cement mortar 1: 3 on concrete surfaces of ceiling,chajja,etc finished fair and even complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

M&L for preparation of new surfaces (plastered or un-plastered) of wall and applying two coats of oil bound distemper complete all as specified and as directed

M&L for old decorated surfaces plastered or unplastered surface of wall and complete removal of existing treatment by rubbing , brooming down, washing with water etc applying two coat of oil bound distemper on wall complete all a specified and as directed.

M&L for Preparation of new surfaces (Plastered or un-plastered) of ceiling and applying two coats of oil bound distemper complete all as specified and as directed.

M&L for Preparation of old surfaces (Plastered or un-plastered) of ceiling and applying two coats of oil bound distemper complete all as specified and as directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L brick work in cement mortar (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x125 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.(MS hold fast/hugs or SS dash fasteners shall be paid for separately) Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.(MS hold fast/hugs or SS dash fasteners shall be paid for separately) Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer?In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed.

Providing 35mm thick FACTORY MADE B/S PRELAM WIRE MESH SOLID PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rails. M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded Prelam sheet 'C' channel made from 5mm (±0.25) thick PVC Sheet of Density 600 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, of size 35mm thickness, 115mm width out of which 100mm shall be flat and 15mm shall be bent in 90° angle on either side forming stiles,one of the 90° bend edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws. 5mm (±0.25) thick 140mm wide PVC sheet out of which 125mm shall be flat and 15mm shall be bent in 90° on the inner side to form top and bottom rail and 155 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90° on both side to form lock rail. An additional 5mm (±0.25) thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent cement adhesive. Panel will be of GI /SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top, bottom & lock rail is sealed with 15mm x15mm tube with steel screw of size 13/6 mm.10mm (5mm x 2nos) thick PVC strip of 25mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top, bottom & lock rail. 10mm thick (5mm x 2nos) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws door seal with aluminum strip drilled suitable to pass through both the walls of the M.S tube. Other hardware’s should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer?In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 45 x 70 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.(MS hold fast/hugs or SS dash fasteners shall be paid for separately) Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S & F for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 100mm size butt hinges stainless steel of AISI 304 complete all as specified and directed.

S&F 300 mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clipss of sheet, cast or extruded sections and fixing bolts and fixed etc complete all as specified and directed.

S&F stainless steel of AISI 304 grade barrel tower bolt 200 mm long, extruded section, etc complete all as specified and directed.

S&F stainless steel of AISI 304 grade handle of size 200mm size long etc. complete all as specified and directed.

S&F brass magic eye for panelled/flush shutter 35mm thick complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. .

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets.

S&F of Stainless steel auto closing hinges openable at 0 degree for kitchen cabinet shutters and bed room cub boards complete all as per specified and directed. Make; ( Hettich, Ebco, Prime )

S&F of stainless steel handles 100 mm size for kitchen cabinet shutters and bed room cub boards complete all as per specified and directed. Make: ( Hettich, Ebco, Prime, Inox )

S&F brass chromium plated tubular hanger rod 20 mm dia with suitable brackets complete all as specified and directed.

S&F for PVC magnetic door catches of kitchen cabinet and similar work fixed with MS screws.

S&F SS tower bolt size 125mm complete complete all as specified and directed..

S&F 100 mm long, stainless steel of AISI 304 grade, hasp and staple, safty type, incl bolt to hinge plate and fixed with screws etc. complete all as specified and directed.

S&F, 25mm dia SS curtain rods fency type, including SS bracket and SS side bulb decorative type complete for doors and windows as required complete all as specified.

Distmantling of ceiling boards (fibre, pulp, insulation etc.) or insulation bords/ slab/blankets, any thicness, including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame (with minimum 15 micron uniform anodic coating) size of 605mm x 605mm consisting of Tee/Angle section, size 40 x 40 x 2mm as approved make confirming to IS-733 in frame of false ceiling including aluminium cleat with necessary CP brass/stainless steel shunk screws. Aluminium perimeter angles fixed to wall/wooden frame at centre to centre and fixing frames to level adjusting anchors 8mm dia GI wire with hook in Tee members at 1.5m centre to centre fixed to steel trussed roof complete all as specified and as directed.

M&L 4mm thick non asbestos fibre cement building boards fixed or laid/inserted to aluminium frame work with screw in ceiling .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for MS framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; and similar work con- forming to Fe.290.Gde-E-165 all as specified and directed.

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified

M&L for sand filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

M&L for glosy finished coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and directed.

Removing excavated soils exc. 50m and and n. ecx 500 mtr depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed.

M&L Cutting of shrubs/bushes and small plants/vegetation including cutting of trunk n.exc 30cm girth and branches and digging out roots from floor or roofs and walls of up to four storied bldg and making good the dismantled portion in cement mortar 1:3 to match the existing surfaces complete all as specified.

S&F PVC laminated GI wire 2.00mm dia for cloth drying with S&F fastener as per site requirement complete all as specified and directed.

Demolition of reinforcement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Reinforced cement concrete type B-1 (1:2:4) using 20 mm graded aggregates in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, parapets, shelves, water staging etc and (necessary form work is included with the item rate upto four sotrey bldgs)

M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Description of Work / Item(s)

Amount

Taking down carefully the old U/S Copper/Aluminium point wiring (light, fan, socket or power) complete fitting such as switch, ceiling roses, pendants, socket, regulators, all type fitting, security light Ding Dong Bell etc and making good to disturbed surfaces of wall including necessary touch up with the adjoining surface of disturbed area i.e with OBD/Colour wash/white wash as per existing finish complete. all as specified and as directed.

M&L for point wiring complete with single core multi strand copper conductor 1.5 Sqm nominal area PVC insulated FRLS 1100 Volts grade electrical cable in and including concealed PVC conduit medium grade and Modular sunken pressed steel terminal box 2 mm thick required size including modular plate and modular flush box in different module with all accessories including 1.5 Sqm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and directed by Engr-in Charge. Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete. One light /fan/Bell point/security light controlled by one way switch

All as per item No 2 here-in-before One socket outlet 5 Amps on same board with cables 1.5 Sqmm size for phase and neutral and 1.5 Sqmm for earthing.

All as per item No 2 here-in-before One socket outlet 5 Amps on independent board with cables 1.5 Sqmm size for phase and neutral and 1.5 Sqmm for earthing.

All as per item No 2 here-in-before One socket outlet 15 Amps on independent board with cables 2.5 Sqmm size for phase and neutral and 2.5 Sqmm for earthing.

All as per item No 2 here-in-before One AC point on independent board with cables 4 Sqmm size for phase and neutral and 4 Sqmm for earthing.

All as per item No 2 here-in-before One light point controlled by two 2-way switch 230 volts with cables 1.5 Sqmm size for phase and neutral and 1.5 Sqmm for earthing.

S&F Switch modular type, 6A 1 way SP switch with fire proof terminal complete all as specified and as directed.

S & F modular type 2/3 pin combined shuttered type 6A 2M socket complete all as specified and directed by Engineer in Charge

S & F Switch Modular type , 6 A 2- way 1 M with fire proof terminal complete all as specified and directed by Engineer in Charge

S & F Switch Modular type switch, 16 A 1- way 1M SP switch with fire proof terminal complete all as specified and directed by Engineer in Charge

S & F modular type 2/3 pin combined shuttered type 16 A 2M socket complete all as specified and directed by Engineer in Charge

S& F Modular AC Box Metal box, power socket with top 240 volts AC complete with one SP MCB, 20 amps all as specified and directed.

S&F in replacement of lamp holder Angle/Batten type bakelite insulated body with back plate all as specified and directed by engr in charge

S & F ceiling rose complete all as specified and directed by Engineer in Charge

S&F electric bell ding dong AC, 230 volts single phase complete all as specified and directed.

S&F Bell push modular type 1M 5/6 Amp complete all as specified and directed.

S&F in replacement Wall mounted LED Integrated Batten 20 Watt - 4Ft White, indoor decorative PVC extruded LED battern-Integrated type in replacement of old unsv existing 36/40 Watt FTL fittings any type, complete all as specified and directedby engr in charge.

S&F in replacement Wall mounted LED Integrated Batten 10 Watt-2 Ft White, mirror light fitting indoor decorative PVC extruded LED battern -integrated type. in replacement of old unsv existing 18/14 Watt FTL fittings any type, complete all as specified and directed.

S&F in replacement 10W LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unsv bulk head/Sketch/LF fitting including all accessories connecting up twin core flexible copper conductor cable complete all as specified and directed

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F of Decorative wall light mounting suitable for LED Lamp upto 12 Watt including Led Bulb 12W complete with all connections all as specified and directed.

S & F 30 Watt security light high efficiency long life LED module with LENS type LED package mounted on MCPCB, Fixture should have minimum efficiency at system level >=110 lumens/Watt, integral SMPS based constant current electronic LED driver with THD<10% surge voltage protection of > 5.0 KV, CRI>80, PF>0.95,CCT 4000-6500K and other safety tests as per IS:15885( part-2/sec-13),IP 66 protection high efficiency polycarbonate cover with integrated lens housed in pressure die cast aluminim alloy heat sink for effective thermal management strudiness excellent corrosion resistance separate optical and control gear compartment & Top opening for easy maintanance suitable for side entry wall mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible copper cunductor cable of appropriate size and 1.5m long bracket having 40mm diameter light grade GI pipe including GI clamp nuts bolts & washers with two coats of synthetic enemal paint over a coat of oxide primer complete all as specified and directed by Engineer in Charge

Supply and fixing Exhaust fan Sweep : 300mm, Power : 34W, Air Delivery : 810 CMH, RPM: 1100, ISI mark metal body including single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm for connection from ceiling rose to fan complete all as specified and as directed. Note:-(i) suitable size hole for fixing exhaust fan will be done by contractor with good finish where it is required.

Supply, Installation, testing and commissioning of 1200mm sweep BEE 5 Star rated, ceiling fan with remote control, suitable cell for remote, Modular Fan regulator Brush Less Direct Current ( BLDC) Motor, Class of insulation: B3Nos Blade, 30 Cm long down road, 2 Nos canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery not less than 220 CMM, 350 RPM( tolerance as per IS: 374-2019), THD less than 10% and all remaining accessories including safety pin, nuts bolts, washers, temperature rise = 75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50Hz, single phase Ac Supply including taking down old ceiling fan and depositing to MES store yard complete all as specified and as directed.

S&F in replacement of VTPN DB 4 way double door vertical type with gasket for fixing MCCB 4 Pole up to 160 Amps as incomer and MCBs as outgoing with metal door and IP-43 protections and connecting complete all as specified and as directed.

S&F in replacement of MCCB thermal magnetic electric release, fixed type, 4 pole, 160 Amps, 415 Volts with rupturing capacity 16 KA including electrical connection with incomer with appropriate size of aluminum lugs and insulation packing complete all as specified and as directed.

Supply and fix in replacement of 12 way double door metallic DB with gasket conforming to IEC 61439-3 suitable for flush/surface mounting having 100A copper busbar fully shrouded neutral bar wirep set & cable ties for cable management pre fitted sheet etc. having IK 09 & IP 43 protection with IS 732:2019 complete all as specified and as directed.

M&L in replacement MCB SP 'B' curve 63 Amps 240 Volts , 10 KA complete all as specified and directed.

M&L in replacement MCB SP 'B' curve 06 to 32 Amps 240 Volts 10 KA complete all as specified and directed.

Supply and fixing RCBO, 230 V, 40 Amp, 30mA 50 Hz with 10KA short circuit capacity of double pole for ensuring protection from leakage current, short circuit & over load to the user for a particular cicuit in normal use it is safe to use and free of threat to user as well as to environment in accordance with IS 12640-2 & IEC 61009-1 in the SPN DB as outgoing all as specified and directed.

S &F in replacement for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in drg and connected to earth test point including testing as directed by Engr-in-Charge.

Supply & fixing of water storage heater, 5 star, Glass lined enamel coated incoloy heating element ,Digital temperature display, Feather touch buttons, Shock resistant injection moulded ABS body, IPX4 waterproof technology, Tank design is suitable to withstand 8 bar pressure (Geyser) of capacity 25 litre ISI mark, , AC, electric, 230 volt, complete , 3 core lead, including PRCD Plug top, safety valve, including electric and water connection and making good to disturbed surface including taking down existing water storage heater complete all as specified and directed. (Note : Existing geyser to be taken down from wall and deposit to the MES Yard for custody BER Board is in process). Note:- (i) Electric switch for geyser of 16 Amps shall be provided on main switch board of the bathroom and socket outlet shall be provided near the geyser and will be measured as 16 amps power wiring against respective item.

S&F Earth Leakage Circuit Breaker 16A, 30 mA, 1P+N C 16 ELCB with sheet metal enclosure distribution board for geyser complete all as specified and as directed.

S&F PVC connection with brass nipple 15 mm x 600 mm long with ISI marked suitable for hot and cold water of 25 ltrs capacity of geyser as hot and cold water connection complete all as specified and directed.

Taking down unserviceable Submain wiring of any size complete and making good disturbed surface complete all as specified and directed.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 6 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed Note:- the rate is inclusive of making good the disturbed surface and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash and wall putty where ever required.

Taking down and re-fixing single phase static energy meter in meter box in and including its connection complete and mounting on existing wall surface including necessary connections of incoming and out going cables. as specified and directed by Engr-in-charge.

S&F in replacement Sheet metal enclosure of size 350 x300 x 150 mm suitable for mounting Single phase electric meter fabricated from 2mm thick CRCA sheet with anti corrosive dust and vermin proof including taking down meter and refix after completion of wiring work including connection with 6 Sqmm wire from DB to Meter . Note:- The meter cover shall have a fully transparent window. The window shall be of transparent, high grade UV stabilized engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover all as specified and directed.

Supply & laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and as directed by Engineer In Charge.

Supply and laying Bricks common burnt clay building bricks sub class A designation 75, size 230mmx115mmx75mm complete all as specified and directed.

Supply and laying High density polyethylene(HDPE) pipes of pressure rating 6kgf/sq.cm (IS marked) and laid in trenches/under roads/ in drains/fixed to poles/walls of size 50 mm Dia complete all as specified and directed.

S&F in replacement, motor Exhaust Fan PVC body 250mm sweep copper winding as per existing , painting, assembling of fan including replacement of nut , bolts,bearing, and connecting cable where ever required complete all as specified and as directed

S&F in replacement,motor Exhaust Fan metal body 300 mm sweep copper winding as per existing , painting, assembling of fan including replacement of nut , bolts,bearing, and connecting cable where ever required complete all as specified and as directed

AMIT ASSOCIATES (BID ID -3100456)

Global Enterprises (BID ID -3098215)

ASSOCIATED CONSTRUCTION CO. (BID ID -3100025)

Phoenix Infra (BID ID -3099189)

Third Wave Services Pvt Ltd (BID ID -3095503)

India Guniting Corporation (BID ID -3100814)

GOYALA INFRA PROJECTS PVT LTD. (BID ID -3098903)

M/s Highway Construction (BID ID -3098032)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3096789)

M/s Matadeen Ramchandra Agarwal (BID ID -3098867)

Jeet Construction (BID ID -3098671)

NARSINGH DEVELOPERS LLP (BID ID -3100240)

SOOD ASSOCIATES PVT LTD (BID ID -3100563)

ASSOCIATED CONSTRUCTION CO. (BID ID -3100025)

AMIT ASSOCIATES (BID ID -3100456)

Global Enterprises (BID ID -3098215)

GOYALA INFRA PROJECTS PVT LTD. (BID ID -3098903)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3096789)

PRAGMATIC INFRASTRUCTURE LIMITED (BID ID -3100566)

NARSINGH DEVELOPERS LLP (BID ID -3100240)

Third Wave Services Pvt Ltd (BID ID -3095503)

M/s Matadeen Ramchandra Agarwal (BID ID -3098867)

Jeet Construction (BID ID -3098671)

India Guniting Corporation (BID ID -3100814)

M/s Highway Construction (BID ID -3098032)

SOOD ASSOCIATES PVT LTD (BID ID -3100563)