Construction of CFC Phase 1 leveling and boundary wall covering the area of 4 kanals at Hutt Pyt. Hutt. Under DDC Capex Plan

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared.

Earthwork in excavation by mechanical means (Hydraulic excavator) in trenches for foundation, drains, pipes etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10sqm on Plan, including dressing of sides and ramming of bottoms, including getting out the excavated earth and disposal of surplus excavated earth as directed, including all leads and lift. a) All Kind of soil.

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:5:10 (1 cement:5 coarse sand:10 graded stone aggregate 40mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centring ,shuttering, finishing and reinforcement. All work upto plinth level with: a) 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: a) 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:6 (1 cement:6 coarse sand) (including all leads and lifts carriages of material by MT/HL).

Extra for brick work with common burnt clay bricks / cement concrete bricks in superstructure above plinth level upto floor five level (including all leads and lifts carriages of material by MT/HL).

Half brick masonry with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:4 (1 cement:4 coarse sand) (including all leads and lifts carriages of material by MT/HL).

Extra for brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means (including all leads and lifts carriages of material by MT/HL).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). a) Sal wood.

Providing 40x5mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix. (1 cement: 3 coarse sand :6 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Reinforced cement concrete work in beams, suspended floor, roofs having slope upto 15˚, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with: a) 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Steel Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. a) Cold twisted bars.

Centring and shuttering including strutting, propping etc.and removal of form work for :

a) Foundation, footings, bases of columns etc. for mass concrete.

b) Suspended floors, roofs, landings, balconies and access platform

c) Lintel, beams, plinth beams, girders, bressumers and cantilevers.

d) Edges of slabs and breaks in floors and walls under 20cm wide.

e) Columns, pillars, piers, abutments, posts and struts.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. a) Fixed to openings/wooden frames with rawl plugs screws etc.

6mm cement plaster to ceiling of mix. 1:3 (1 cement:3 fine sand) (including all leads and lifts carriages of material by MT/HL).

15mm cement plaster on the rough side of single or half brick wall of mix. 1:6 (1 cement: 6 fine sand) (including all leads and lifts carriages of material by MT/HL).

12mm cement plaster of mix. 1:6 (1 cement:6 fine sand) (including all leads and lifts carriages of material by MT/HL).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screw, excluding paneling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:Butt hinges and necessary screws shall be paid separately). a) Second class deodar wood (including all leads and lifts carriages of material by MT/HL).

Providing and fixing paneling or panelling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled or paneled and glazed shutters 25mm to 40mm thick. a) Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS:3087 marked.

Providing and fixing 30mm glazed shutters for doors, windows and clerestory windows using 4mm thick float panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. a) Second class deodar wood.

Providing and fixing 30mm wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4mm in both directions with wire of dia. 0.63mm for doors, windows, and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screw as per direction of Engineer-in-charge. a) Second class deodar wood.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete (including all leads and lifts carriages of material by MT/HL).

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement)3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. including pointing in white cement mixed with pigment of matching shade complete (including all leads and lifts carriages of material by MT/HL).

Providing and laying vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. a) Size of tile 600x600mm. (including all leads and lifts carriages of material by MT/HL).

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screw etc. complete.a) 300x16mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screw etc. complete.

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminum casement stays, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screw etc. complete.

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron / steel works.

Applying priming coat with ready mixed pind or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. a) 2mm thick.

Painting with oil type wood preservative of approved brand and manufacture on New work (two or more coats).

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. a) White vitreous china wash basin size 550x400mm with a single 15mm C.P. brass brass pillar taps.

Providing and fixing informatory sign board including writing painting etc. complete job as per direction of Engineer-n-charge.

Carriage of the following materials by Mechanical Transport from source to site of work incl. loading, unloading and stacking complete :- a) Sand from Kathua for an average lead of 129.00 Km. by M.T. b) Stone aggregate 40mm nominal size & above from Kathua for an average lead of 129.00 Km. by M.T. c) Stone aggregate (Crusher bajree) below 20mm nominal size Kathua for an average lead of 129.00 Km. by M.T. d) Bricks Kathua for an average lead of 129.00 Km. by M.T..

Romesh Chander

SHANKER DASS