REPAIRS, REPLACEMENT OF TILING IN KITCHEN , BATHROOMS , TOILETS, PVC TANKS , JOINERY , SANITARY FITTINGS , PLUMBING WORKS AT Ors MD ACCN UNDER AGE BR-1 OF GE (CENTRAL) BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcand removal of entire debris as ordered outside MD land complete all as directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MoD Premises complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 3 here-in-above but exceeding 1.5Sqm but not exceeding 4 Sqm each

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each and stacking at site where directed.

All as per item No 5 here-in-above but exceeding 2 Sqm -do-

M & L for PCC 1 :4 : 8 type D2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO , Acco Proof , Impermo , Aqua flex as approved.

S &F 30 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F 30mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

S&F powder coated anodised aluminium window and ventilator shutter, side hung type without sash or sliding type, aluminium sections weighing 0.55kg/m incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long(2 no) suitable handle (1 no) complete all as specified.

S & F aluminium grill ( anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC15) of approved design/pattern,with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws @ 200mm centre to centre, including cuttings the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standardsection around the opening, all complete as per requirement and as directed.

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F100 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&F 150 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 150 mm size (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as directed.

S & F in repair 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as directed including taking down old towel rail.

S&F in stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as directed.

All same as per item No 22 here-in-above but in repairs -do-

S&F Bands, straps, supports or stays for rainwater, hold fasts; wall ties; and similar small articles steel conforming to Fe-290 Gde-E-165.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing the same with neat cement slurry with 3.0 Kg of cement per Sqm complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 350x250x7mm / 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 27 & 28 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M & L rendering 15 mm thick CM 1:6 on stone masonry surfaces other than fair face of brick work or one sided lathing finished followed by 10mm thick settting coat in CM 1: 6 inclding finishing surface even and smooth without using extra cement in walls complete all as specified and directed by Enigineer in Charge

M&L for rendering 15 mm thick in CM 1:6 on brick work/stone work or concrete surface finished the surface even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick in CM 1:6 on brick work/stone work or concrete surface finished the surface even and smooth without using extra cement complete all as specified.

All as per item No 31 here-in-above but 5 mm thick in CM 1:3 on ceiling,chajja,roof projection etc.

Three coats of white wash on newly plastered surface of walls after necessary preparation of surface complete all as directed.

All same as per item No 33 here-in-above but on ceiling surface -do-

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Hacking out old broken glass (any thickness) and size from wooden frame glazed with putty or fixed with wooden beads and removal of debris to a distance n.exc 50 mtr and depositing where directed.

S&F sheet glass 4mm thick glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

S&F sheet glass 4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

S & F in repair PVC flush handle including connecting rod & syphon washer suitable for 10 litre capacity PVC flushing cistern complete all as directed.

S & F in repair PVC syphon set complete suitable for 10 litre capacity PVC flushing cistern complete all as directed.

Replacing old unserviceable steel brackets for wash hand basin (Flat or angle back) including cutting for pinning in end of 12mm dia bolt erecting stand, inlet and outlet screwed for pipe or connection including necessary packing all as directed.

S&F in repairs 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified & as directed.

S&F in repairs brass chromium plated shower rose 125 mm dia with or wihout swivel joint, any size, including fixing to steel pipe or union.Make : CERA Cat No F 7020304 or equivalent of Make Hindware/Parryware/Prayag

S&F in repair sinks made of stainless steel ( gde 304) 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size (Approximate) 915mm x 460mmx203mm bowl size 405mm x 354mmx203mm (Make: Prayag Cat No 1322D or equivelent of Parryware /Hindware/Cera)

Supply and fixing in repair 32mm dia waste fittings brass CP fixed to WHB complete all as spd and directed by Engg-in-Charge

All same as per item No 47 here-in-above but 40mm dia suitable for sink etc

S & F in repairs PVC connection pipe with PTMT nuts, 600mm long complete all as specified

S&F 32/40mm bore Low density polyyethylene (LDPE) pipes of pressure rating 6 kgf/Sqcm with connecting bracket fixed to waste coupling for basin/sinks complete all as specified and directed.

S & F in repair 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches complete all as specified and directed.

S & F in repair 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches complete all as specified and directed.

S & F in repair 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes or for rain water pipe in any length without ears, with rubber ring joints fixed to wall using MS holder bat complete all as specified and directed.

S & F in repair 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes or for rain water pipe in any length without ears, with rubber ring joints fixed to wall using MS holder bat complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single Y) 110 mm dia equal or unequal with oval access door complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single Y) 75 mm dia equal or unequal with oval access door complete all as specified and directed.

S&F PVC (SWR) branch piece (double Y) 110 mm dia equal or unequal with oval access door complete all as specified and directed.

S&F PVC (SWR) branch piece (double Y) 75 mm dia equal or unequal with oval access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with access door

S&F 75 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with access door

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S & F in repairs PVC seat cover for EWC white / Black colour complete with MS Hinged cromium plated make as per existing all as specified and as directed

S&F in repair steel chromium plated gratings, circular type, 125mm dia with or without waste hole fixed to existing traps with white cement complete all as directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe with PVC connection pipe 15 mm dia 600 mm long etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as directed.Make of cistern CERA Cat No B1010109 or equivelant of PARRYWARE/HINDWARE/PRAYAG

Disconnecting existing tanks, setting aside ( for lowering if required) for repairs, cleaning,etc and hoisting if required reconnecting and refixing in positing including cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes. ( Capacity exc 500 but n exc 1000ltrs)

All same as per item No 69 here-in-above but tank of size exc 250 lts but not exc 500 lts -do-

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

S&F in repairs 20 mm ball valves, high pressure with polyethylene float and flynut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Material and labour for removal any type of existing treatment from sunken slab in any description or any other kind of treatment surface over sunken slab including plastering and cleaning of surface with wire brushes and water removing of unsolvent materials and depositing of the same as directed outside of MoD land and 25 mm thic PCC concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregrate mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on sunken slab surface once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.30 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cm end lap torch sealed and bonded as per detailed procedure , applying bitumen grade 82/25 over the surface &1.20Kg/Sqm to entire floor & wall surface as directed and finally finished the top surface with 25 mm thick plastering in CM 1:4 mixed with liquid water proofing admixture as per manufacturer's instruction's complete to the satisfaction of Engineer-in-charge . Note: (i) The quoted rate is deemed to be inclusive of taking down & removal of debris , 25 mm thick PCC , Complete APP treatment , Bitumen primer 85/25 grade & 25 mm thick plastering . (ii) Quted rate is deemed to be inclusive of WPC (iii) The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface.

Removing complete shrubs/ vegetation upto root grown in any description such as grown in wall / beam / roof /chajja etc in height up to three storey building including filling the holes where the shurbs removed with cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) of minimum size 15cm x15cm x 15cm or as required and making good the distured surface as per its original specification to the satisfaction Engineer-in-charge& removal of the taken out shurbs out of MD land and disposed complete all as directed.

M AND V ENTERPRISES

PRAGATHI BUILDERS

PRACHANIVA CONSTRUCTIONS

shri veerabadreshwara enterprises