REPAIRS TO WOODEN FURNITURE, REWEAVING, CANING AND POLISHING OF WOODEN FURNITURE UNDER GE (NW) KARANJA AT NAVAL STATION KARANJA

Amount

Removing of existing worn out cane and supply and recanning with new plastic cane 2mm wide half round for weaving and 4mm wide half round for border of cream colour to all types of chairs as per Godrej Pattern, stool dressing couches, bin soiled linen etc, all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-16/17/201/229

Removing unserviceable nylon tape newar from charpoy GI pipe and tightening the loose steel frame and supply and reweaving with new nylon newar of white coloured (not made out of recycled nylon) and of width 50mm, weight not less than 1.50 Kg per charpoy and 14 long and 34 short bends and weaving of nylon on both sides of charpoy all as shown on drawing. The cut ends of nylon newar shall be stitched properly and tied instead of screwing as per drawings. complete all as specified and as directed by Engr-in-charge. Drwg No: FD-220

Removing of old unserviceable cushion foam of 5 seater sofa set and supply only new cushion of 525x525x100mm, 32 density for single seat and back all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-258/281

Supply and fix of cushion cover made of superior quality tapestry cloth along with Kora cloth with openable arrangement by providing zip of required size all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-258/281

SOFA SET 5 SEATER Supply and fix in repairs for the following parts of sofa set 3 pieces 5 seats with Ist class hard wood as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-258/281

SOFA SEAT OF LONG PIECE (Drwg No: FD-258/281) legs

Front rail

Side rail

Batten

Stiffener

SOFA BACK OF LONG PIECE (Drwg No: FD-258/281) Side rail

Front rail

Batten

SOFA SEAT OF CHAIR SET (Drwg No: FD-258/281) legs

Front rail

Side rail

Batten

Stiffener

SOFA BACK OF CHAIR SET (Drwg No: FD-258/281) Side rail

Top rail

Bottom rail

Batten

Material and labour for polishing of sofa set 5 seater (3+1+1) with high class lekar polish to all exposed surfaces match with existing complete all as specified and as directed by Engr-in-charge.

BED PLY WOOD TOP Supply and fix in repair for the following parts of bed plywood top as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-246/247

Head rest

Foot rest

Long rails

Short rails

Stiffener

MS bracket of flat iron 25x3mm, 200mm long fixed with screws

Plywood top 12mm thick BWR type as per existing shape and size in one piece

Material and labour for polishing of bed plywood top with high class french polish to all exposed surfaces except top and bottom after preparation of surfaces complete all as specified and as directed by Engr-in-charge.

REPAIR TO TABLE 900mm X 600mm WITH DRAWER Supply and fix in repair of the following parts of table 900x600mm with Ist class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-224/283

Long rail

Short rail

Bottom side stiffener

Bottom centre stiffener

Drawer with 6mm thick commercial ply at bottom only and sides, back shall be 12mm thick Ist class hard wood (teak) with knob.

Taking out old unserviceable top supply and fix for new top of prelaminated particle board one side teak wood face 18/19mm thick including 6mm thick teak wood beading all round all as shown on drawing.

Material and labour for polishing of table 900x600mm with drawer with high class french polish on all exposed surface except top and bottom including matching new components with old one after preparation of surfaces.

REPAIR TO TABLE 900mm x 600mm WITH OUT DRAWER: Supply and fix in repair of the following parts of table 900x600mm without drawer with Ist class hard wood (teak) as per existing shape and size duly planned all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-231/284

Long rail

Short rail

Bottom side stiffener

Bottom centre stiffener

Taking out old unserviceable top supply and fix new top of prelaminated particle board one side teak wood face 18/19mm thick including 6mm thick teak wood beading all round all as shown on drawing.

Material and labour for polishing of table 900x600mm without drawer with high class french polish on all exposed surface except top and bottom including matching new components with old after preparation of surfaces.

REPAIR TO TABLE 900x900mm: Supply and fix in repair for the following parts of the table 900x900mm with Ist class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-88(M)/291

Long rail

Short rail

Table top of 18/19mm thick prelaminated particle board one side teak wood face and other side white balancing including 6mm thick teak wood edging all round all as shown on drawing.

Material and labour for polishing of table 900x900mm with high class french polish on all exposed surfaces except top and bottom including matching new components with old one after preparation of surfaces.

REPAIR OF TABLE BED SIDE: Supply and fix in repair of the following parts of table bed side with 18mm thick prelaminated particle board as per existing shape and size duly finished as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-248/276

Shelf

Bottom

Back shall be made of 6mm thick plywood commercial as per existing shape and size.

Ist class hard wood (teak) 6mm beading at front on 18mm thick prelaminated particle exposed portion of table bed side.

Ist class hard wood (teak) frame with 4 Nos of legs duly french polish.

REPAIRS OF TEAPOY: Supply and fix in repairs of the following parts of teapoy with Ist class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-232/278/382

Long rail

Short rail

Side stiffener

Centre stiffener

Taking out old unserviceable top and supply and fix new top of made of 18/19mm thick prelaminated particle board one side teak face and other side white balancing exterior grade with including 6mm thick wood beading all round the top all as shown on drawing.

Material and labour for polishing of teapoy with high class french polish on all exposed surface except top and bottom including after preparation of surfaces.

REPAIRS OF PEG TABLE: Supply and fix in repair of the following parts of table peg with Ist class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-236/266/277/384

Long rail

Short rail

Side stiffener

Taking out old unserviceable top and supply and fix new top of made of 18/19mm thick prelaminated particle board one side teak face and other side white balancing exterior grade with including 6mm thick Ist class hard wood (teak) beading all round the top all as shown on drawing.

TABLE WRITING: Supply and fix in repair of the following parts of table writing with Ist class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-275

Long rail of table frame

Short rail of table frame

Drawer including chromium plated knob of 40mm dia

Bottom centre stiffener

Bottom side stiffener

Taking out old unserviceable top and supply and fix new top of prelaminated particle board one side teak wood face including 6mm thick teak wood beading all round top duly high class french polish all as shown on drawing.

REPAIR TO TABLE CENTRE: Supply and fix in repair of the following parts of table centre with Ist class wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-235/274

Long rail

Short rail

Side stiffener

Taking out old unserviceable top and supply and fix new top of made of 18/19mm thick prelaminated particle board one side teak face and other side white balancing exterior grade with including 6mm thick wood beading all round the top all as shown on drawing.

REPAIR TO TABLE DINING 06 /08 PERSON: Supply and fix in repair of the following parts of table dining 06/ 08 person with 1st class hard wood (teak) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-239/269/273

Taking down old unserviceable top of table dining 06 /08 person and supply and fix new top of 18mm thick prelaminated particle board one side teak face and other side white balancing exterior grade with incluidng 6mm thick teak wood beading all round the top duly high class french polish.

Long rail

Short rail

Stiffener

CHAIR DINING (MAP): Supply and fix in repair of the following parts of chair dining of 1st class hard wood (shisham) as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD/E/MAP/10 & FD/E6/MAP/10(R)

Rear legs

Front legs

Side rail of seat frame

Front /back rails of seat frame

75mm thick 40 density cushion of approved foam covered with approved tapestry cloth shall be fixed over 12mm thick ply all as shown on drawing.

Bottom stiffener

Vertical back stiffener

Nylon buffers on the bottom of legs

Material and labour for polishing of chair dining with high class french polish to all exposed surfaces except inside of seat frame (4 sides) including matching with new component with old one after preparation of surfaces.

REPAIR TO STOOL DRESSING: Supply and fix in repairs of the following parts of stool dressing with Ist class hard wood (teak) as per existing shape and size duly all as shown on darwing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-252/282/374

Side rails of seat frame including holes for weaving (spacing of holes shall be match with the existing rail)

Front/ back rails of seat frame including drlling holes for weaving (spacing of holes shall be match with the existing rail)

Recanning seat with new 2mm wide half round white plastic cane of superior quality in Godrej pattern

Material and labour for polishing of old/ new surfaces with high class french polish to all exposed surfaces all as shown on drawing.

REPAIR OF TABLE DRESSING GENTS: Repair of following parts of table dressing gents as per existing shape and size duly planned and finsihed all as shown on darwing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-31(M)/230

Removal old unserviceable looking glass and fixing new glass of 5mm thick as per existing shape and size.

Removal old unserviceable back ply of glass and fixing 6mm thick commercial plywood of existing shape and size.

Removal of old unserviceable drawer and fixing new drawer made of prelaminated particle board and 6mm thick plywood commercial as per existing shape and size all as shown on drawing.

Removal of old unserviceable prelaminated particle board top of table and fixing new 18mm thick prelaminated particle board as per existing shape and size all as shown on drawing.

REPAIR OF TABLE DRESSING LADIES: Repair of following parts of table dressing ladies as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-32(M)/251

Removal old unserviceable looking glass and fixing new glass of 5mm thick as per existing shape and size.

Removal old unserviceable back ply of glass and fixing 6mm thick commercial plywood of existing shape and size.

Removal of old unserviceable sliding glass and fixing new glass of 3mm thick as per existing.

Removal of old unserviceable prelaminated particle board top of table and fixing new 18mm thick prelaminated particle board as per existing shape and size.

Removal of old unserviceable leg of table and fixing new legs of 1st class hard wood (teak).

Removal of old unserviceable drawer and fixing new drawer of 6mm thick plywood commercial with front 18mm prelaminated particle board as per existing shape and size.

REPAIR TO SIDE BOARD: Supply and fix in repair of the following parts of side board as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-241

Bottom

Shelves

Drawer shall be made of 6mm thick commercial plywood with 18mm thick prelaminated particle board front.

Shutter with 40mm size knob.

Back shall be made of 6mm thick commercial plywood.

Bottom frame with 4 Nos of legs shall be made of Ist class hard wood (teak).

Material and labour for polishing of side board with high class french polish on all exposed surfaces except top and bottom including after preparation of surfaces.

CHAIR EASY: Supply and fix in repairs of the following parts of chair easy with 1st class hard wood as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-17(M)/201/229

Rear legs

Front legs

Side rails

Front/ back rails

Back stiffener

Bottom stiffener

Arms rest

Material and labour for polishing of chair easy with high class french polish to all exposed surfaces except in side of seat frame (04 sides) including matching with new components with old one after preparation of surfaces.

CHAIR WRITING: Supply and fix in repair of the following parts of chair writing with 1st class hard wood as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-20(M)/202/280

Rear legs

Front legs

Side rail of seat frame including drilling holes for weaving (spacing of holes shall be as per existing).

Front/ back rails of seat frame including drilling holes for weaving (spacing of holes shall be as per existing).

Bottom stiffener

Back stiffener

Arm rest

Material and labour for polishing of chair writing with high class french polish to all exposed surfaces except inside of seat frame (4 sides) including matching with new component with old one after preparation of surfaces.

CHAIR DINING: Supply and fix in repair of the following parts of chair dining of 1st class hard wood as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-16(M)/203/279

Rear llegs

Front legs

Side rail of seat frame including drilling holes for weaving (spacing of holes shall be as per existing).

Front/ back rails of seat frame including drilling holes for weaving (spacing of holes shall be as per existing).

Bottom stiffener

Back stiffener

Material and labour for polishing of chair dining with high class french polish to all exposed surfaces except inside of seat frame (4 sides) including matching with new component with old one after preparation of surfaces.

CHAIR WOODEN BOTTOM: Supply and fix in repair of the following parts of the chair wooden bottom without arms with Ist class hard wood as per existing shape and size duly finished all as shown on drawing complete all as specified and as directed by Engr-in-charge. Drwg No: FD-56(M)/285

Rear legs

Front legs

Side rails

Front/ back rails of seat

Back stiffener

Bottom stiffener

Seat of 6mm thick BWR commercial plywood.

Material and labour for polishing of chair wooden bottom without arms with high class french polish to all expensed surfaces except in side of seat frame (4 sides) including matching with new components with old one after preparation of surfaces.

POLISHING TO WOODEN FURNITURE: Material and labour for preparation for the following of previously treated wooden surfaces of furniture items by scrapping removing and cleaning all dirt/ dust and filling previous surfaces or cavities with filler and applying one finishing coat of french polish of high glossy finish complete all as specified and as directed by Engr-in-charge. Drwg No: DB-4222

Almirah mess utensils Drwg No: FD-93

Almirah wooden large with shelves Drwg No: DB-4160

Almirah wooden large without shelves Drwg No: WDF-3

Almirah wooden large 1/2 shelves 1/2 hanging Drwg No: DB-4049

Almirah medium with shelves Drwg No: DB-3959

Bench workshop type 'B' (10'x4'x3' Top 3" thick) Drwg No: F-42

Bench seating 8'x 2'x1'6" Drwg No: DNC-505

Bench workshop but type 'F' (5'x 2' 6"x2' 6") Drwg No: F-43

Bench workshop but type 'M' (9'x4'x3") with drawer Drwg No: F-96

Almirah map wooden Drwg No: F-22A

Bed newar Drwg No: FD-245

Chair CBA office Drwg No: DB-4124

Form without back Drwg No: FD-77/1027

Hat stand with mirror Drwg No: FD-233/23

Peg table Drwg No: FD-236/25/227

Rack side 3/ 4 spaces Drwg No: DB-4123

Form with back Drwg No: FD-78

Stool wooden 2 feet high Drwg No: F-2

Table 5' x 2' x10" Drwg No: FD-139

Table dining 6 persons Drwg No: FD-239/30/273

Table dressing gents with mirror Drwg No: FD-230

Table dressing ladies Drwg No: FD-32/251

Table bed side Drwg No: FD-248/276

Table dining 8 persons 1800x900x760mm Drwg No: FD-30/239/273

Table office clerk wooden Drwg No: FD-4120

Table office officer wooden Drwg No: FD-4117/SDF-32

M/s S.D Construction Co

SHUBH ASHISH ENTERPRISES

Mahesh Traders