Repair to joinery, plumbing and misc items, paths, MH Officer Mess, Personal lines, LAO, Int and Fd Hospital and Md Accn under AGE B/R-II, GE Gurdaspur.

Amount

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L 15mm thick cement plastering in cm 1:6 on other than fair faces of brick or concrete surfaces , finished the surfaces even and smooth without using extra cement complete all as specified & directed.

M&L 10mm thick cement plastering on fair faces of ceiling in CM 1:3 on brick or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified & directed.

M&L 15mm thick cement plastering in cm 1:4 on fair faces of brick or concrete surfaces, finished the surfaces even and fair, using water proof compound complete all as specified & directed. Note : Water proofing compound shall be measured and paid separately.

M&L preparation of new plaster surface and applying two coats of cement base paint all as specified and directed.

M&L preparation of new plaster surface of ceiling and applying three coats of white wash complete all as specified.

Preparation of new plastered surfaces and applying two coats of oil bound distemper (of approved shade) on walls over priming coat of chalk whiting, on plastered surfaces complete all as specified.

M&L for preparation of old surfaces of existing treatment and applied one coat of cement based paint all as specified & directed.

M&L preparing old plastered or unplastered surfaces of walls and applying one coat coat of white wash complete all as specified and directed.

M&L preparing old plastered or unplastered surfaces of ceiling and applying one coat coat of white wash complete all as specified and directed.

M & L preparing old plastered or unplastered surfaces of walls including cornices and applying one coat of distemper oil emulsion paint, white or tinted complete all as specified and directed.

M & L preparing old decoreted plastered surface by complete removal existing treatment and applying two coats of OBD over 1mm thick wall putty to make surface smooth complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer.

M&L preparation of old painted surface of wood & wood based surfaces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint

M&L preparation of old painted surface of steel surfaces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed

All as per Srl item No 17 above but size of opening exceeding 1.5 Sqm but not exceeding 4 Sqm

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

S&F anodised aluminium powder coated (Minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F anodised aluminium powder coated (Minimum thickness of powder coating 50 micron) window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F anodised aluminium powder coated frame (Minimum thickness of powder coating 50 micron) for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Sheet glass 5.5mm thick , ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane

Supply and fix for pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, including PCC (1:3:6), type C-0, ( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames including one shop coat of priming and two coats of synthetic enamel paint and preparation of surfaces complete all as specified and as directed.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames including one shop coat of priming and two coats of synthetic enamel paint and preparation of surfaces complete all as specified and as directed.

S&F 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels on both sides complete all as specified and directed.

S&F 2nd class hard wood (Hallock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F MS framed work as in door or gates, chowkats of angle or other section with gusset plates, rail, braces, etc and similar work conforming to Fe-290 Grade-E-165 complete.

M&L for PCC type B1, 1:2:4 (20 mm graded stone aggregate) as in hold fast for doors all as specified and directed .

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares n.exc 0.50 Sqm each complete all as specifiwd and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each including hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

S&F in repair 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding/bolts/ screws in metal/wooden frame complete all as specified and directed. .

S&F Aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, through bolt or with screw complete all as specified and directed.

S&F Aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed.

Supply and fixing in repair cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

M & L for 18/19 mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed.

S & F 150 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L plaster 15mm thick in cm 1:3 in sunken portion of slab finished fair and even using waterproofing compound all as specified and directed Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface complete all as specified and directed.

M&L for applying evenly a tack coat of hot industrial bitumen 85/25 at the rate of 1.6 kg per sq.m on roof surfaces complete all as specified and as directed.

M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm but not exc. 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:6 and dismantling of existing tile and screed complete all as specified.

S&F non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 and dismantling of existing tile and screed complete all as specified and directed

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tiles and screed complete all as specified.

M& L for dark coloured vitrified tiles10 mm thick joint free (square/rectangular) area of each tile n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:6 and dismantling of existing tile and screed complete all as specified.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tank complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts, white colour, incl SS L-type jet spray with 1 m hose pipe, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. incl plastic water closet seat cover, white, closed pattern with flat botton and cover with mild steel chromium plated hinging device and fixing bolts complete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 using 40mm graded stone aggregate complete all as specified and directed.

S&F in repair vitreous China wash basin, with full pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling of PTMT (half or full threaded) bore dia of discharge pipe 32mm (Minimum weight 45gms), cutting for and pinning in ends of bracket or errecting stand complete all as specified and directed.

S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) white with grating and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing aroug urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe, brass CP urinal spreader complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

S & F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up or down complete all as specified and directed.

All as per Srl item No 70 above but fixing only (old serviceable pipe re-used inc cleaning and new fittings).

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked including taking up or down complete all as specified and directed.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S & F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ) with oval access door complete all as specified and directed.

S & F in repair 75 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ) with oval access door complete all as specified and directed.

S&F in repair PVC vent cowl of size 110mm.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 100mm dia complete all as specified and directed.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm dia complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F Stack clamps (75 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F in repair 100mm dia stainless steel grating with or without hinge type or hole type complete all specified and directed.

S&F in repair Brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 225mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to low lying areas complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate as in floor finishing even and smooth without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate as in plinth protection finishing fair and even complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of floor to raise level only complete all as specified and directed.

M&L coloured Chequered cement concrete tiles with grey cement and no pigment, 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors in floors over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for machine pressed precast cement concrete interlocking paver block, any shape and size as approved, 60mm thick, conforming to IS 15658-2006, M-35 with grey cement and no pigments in floor/ paths/ pavement including filling the joints with sand complete all as specified and as directed.

M&L for 25 mm Sand filling under floors or in foundations including watering and consolidation all as specified & directed.

Dismantling brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed

All as per Srl item No 97 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 96 shall be reused after necessary cleaning of mortar)

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement morter 1:4, all as specified and directed.

M&L for Green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and dismantling of existing marble and screed complete all as specified and directed.

M&L for RCC in 1:2:4 type B-1(using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work including demlition of existing RCC complete all as spd.

S&F 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips as spd.

Use and waste of form work to chajjas, weather shades, corbels, water troughs, shelves including supports, overhangs and similar items including edges, rough finished surfaces of concrete complete all as specified and directed

Supply and fixing 12mm thick toughened glass with designed pattern including fixing arrangements like suitable hinges, fittings, handles etc complete all as directed.

S&F in repair kitchen sinks made of stainless steel 1mm thick with plugs, washers, wastes and coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm including fittings arrangement complete all as specified and directed

S&F in repair stainless steel kitchen plate rack size 600mm x 900mm x 250mm deep made out of 0.63mm thick stainless steel sheet (Grade AISI 304) including fixing arrangement complete all as specified and directed

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces at any height complete all as specified. Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

S&F GI powder coated grid work of size 605mm X 605mm, with main tee of size 32mm X 23.5mm x 1.5mm thick, cross tee of size 25mm X 23.5mm x 1.28mm and angle of size 23.5mm X 23.5mm x 1.2mm fixed on wall, all powder coated finish on exposed faces of tee and angle, hung from ceiling using 2mm dia. G.I. suspension wires and 'J' bolts, washers, nuts spaced at 1200 mm both ways including making niches for fans/ light including dismantling of old existing gypsum board ceiling and grid complete all as specified & directed.

S&F 12mm thick perforated particle board/tiles for insula-tion and accoustic purposes, 60x60cm in size, fixed with nails to timber frame work or with staples on snap grid complete all as spcd and directed.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

multani construction co

AVTAR SINGH RAJU

DEEPAK AND CO

buta singh and sons

M/s. Nirmal Singh