Renovation works at head office building of Haryana State Pollution Control Board (HSPCB), C-11, Sector-6, Panchkula, Haryana

Name of Work : - "Renovation works at head office of HSPCB, C-11, Sector -6, Panchkula, Haryana."

Sub Head No. Description DSR Amount NDSR Amount

1 Electrical Work 33,580.00 7,429,668.00

4 Active & Passive Work 0 1,022,523.00

Total Amount 15,282,019.00

Total Amount 15,282,019.00

Digitally signed by AMIT

ESTIMATE FOR ELECTRICAL ITEMS FOR HSPCB

DSR E&M AMOUNT

S.No DESCRIPTION QTY. UNIT RATE AMOUNT DSR

SITC of following sizes of 1.1 kV grade multicore aluminium conductor XLPE insulated

1 MR-1 armoured cable, including termination kit, jointing kit conforming to IS:7098 (Part - I)

complete with all amendments etc. as required. complete as per directions of Engineer-

Supplying and installing following size of perforated GI cable trays with perforation not

more than 17.5%, in convenient sections, joined with connectors, suspended from the

2 DSR 4.6 ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as

DSR 4.6.2 150 mm width x 50 mm depth x 1.6 mm thickness 20.00 Metre ₹ 716.00 ₹ 14,320.00

DSR 4.6.4 300 mm width x 50 mm depth x 1.6 mm thickness 20.00 Metre ₹ 963.00 ₹ 19,260.00

3 MR-2 MCCB With Enclosure

Supply, installation, testing and commissioning of sheet metal enclosure with 125 A

a) TPN MCCB. This shall include cable entry boxes both for incoming and outgoing 4.00 Set ₹ 21,600.00 ₹ 86,400.00

cable) ,complete as per directions of Engineer-in-Charge.

SITC of Main HT Incommer Panel including switchgear,800 A VCB breaker and all

4 MR-6 necessary accessories shall be in considered to oprate the Main HT panel. complete 1 Nos ₹ 1,620,000.00 ₹ 1,620,000.00

as per directions of Engineer-in-Charge.

SITC of 140 KVAR Capcitor Bank, rated current for MCCB 400 A (min), ICU ≥45 KA.

5 ICS ≥ 50% ICU for all MCCB. (5)AC Magnetic Contactors. Contactors used for 1 Nos ₹ 640,000.00 ₹ 640,000.00

switching the capacitor sub-banks are designed to withstand the surge currents

associated with capacitive switching, complete as per directions of Engineer-in-Charge.

Supply, Installation, Testing and Commissioning of 500 kVA Linear Servo Voltage

Stabilizer, Input Voltae range from 280 to 460V, Output Voltage 415V, Power Capacity

of 500 KVA. complete as per directions of Engineer-in-Charge.

Digitally signed by AMIT

SITC of 500KVA, 3-Phase, Dry type transformer 11000V/433V, 50Hz, Delta-Star

(Dy11), Indoor type, Cooling mode shall be minimum ANAF, Insulation material shall

7 be Cast resin (HV) and Pre-Impregnated (LV), Minimum IP 31 class enclosure, 1 Nos ₹ 2,550,000.00 ₹ 2,550,000.00

Mounting mode shall be fixed, No-laod secondary Voltage 433V, Rated Insulation level

35KV AC for primary and 3KV AC for secondary, Lighting Impulse withstanding voltage

(1.2/50Ms) is 95KV for primary circuit, Short Circuit Impedance of 4%, Tharmal Class

F, Sound Level 61.8 db at 1m. All the switchgear which are necessary to connect the

Main HT & LT Panel at Transormer shall be in the scope of bidder. Any specification

and accessoies which is not mentioned but required for proper operation must be in

the scope of vendor, complete as per directions of Engineer-in-Charge.

A Total DSR +NDSR amount including GST ₹ 7,463,248.00

Digitally signed by AMIT

NAME OF WORK:- "Renovation works at head office of HSPCB, C-11, Sector -6, Panchkula, Haryana."

Unit Rate NDSR

S.No. DESCRIPTION BOQ Qty. UNIT DSR Amount

I EXISTING WASHROOM RENOVATION

Demolition of Existing toilet and brick / block masonry

work & 12mm or more plaster as required

Dismantling of old plaster or skirting raking out joints and

15.56 cleaning the surface for plaster including disposal of rubbish to 90 Sqm 45.05 4,054.50

the dumping ground within 50 metres lead.

Dismantling/ chipping of concrete: Dismantling & chipping of

existing concrete up to 10 mm behind the main bar carefully by

low impact high frequency hammer without damaging the mother

concrete including cleaning the surfaces and preparing surface

ready to receive new plaster etc. at all height complete and

collecting and stacking of the debris at the lead of 50m at ground

floor in the premises as directed by Engineer in charge,

complete. The rates are inclusive of all materials, labor,

machinery, equipment, tools, tackles etc. and disposal of

debris into approved municipal dumping yards, all complete.

Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 495 Sqm 1018.05 503,934.75

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

bars at every third course of half brick masonry.

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm

13.26 thickness over plastered surface to prepare the surface even and 501 Sqm 214.30 107,364.30

smooth complete.

Dismantling aluminium/ Gypsum partitions, doors, windows,

fixed glazing and false ceiling including disposal of

unserviceable material and stacking of serviceable material

with in 50 meters lead as directed by Engineer-in-charge.

Ceramic Wall tiles for toilets including painting and

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.60.1 Two or more coats on new work 97.15 Sqm 137.85 13,391.99

Flooring of toilets includes water proofing and Marble

stone laying etc.

Providing and laying water proofing treatment to vertical and

horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of: (i) Ist course of applying cement slurry @ 4.4

kg/sqm mixed with water proofing compound conforming to IS

2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm

22.3 cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water 120.00 Sqm 774.25 92,910.00

proofing compound in recommended proportion including

rounding off junction of vertical and horizontal surface. (iii) IIIrd

course of applying blown or residual bitumen applied hot at 1.7

kg. per sqm of area. (iv) IVth course of 400 micron thick PVC

sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified and as directed

by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Replacing of all toilet fixtures including changing of existing

Providing and fixing white vitreous china extended wall mounting

water closet of size 780x370x690 mm of approved shape

including providing & fixing white vitreous china cistern with

dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to

17.78 4 litre/ 8 litres),including seat cover, and cistern fittings, 12 Each 13,036.55 156,438.60

nuts, bolts and gasket etc complete.

Providing and fixing stone slab with table rubbed, edges

rounded and polished, of size 75x50 cm deep and 1.8 cm thick,

fixed in urinal partitions by cutting a chase of appropriate width

with chase cutter and embedding the stone in the chase

with epoxy grout or with cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate 6 mm nominal

size) as per direction of Engineer-in-charge and finished

8.10.2 Granite Stone of approved shade 7.40 Sqm 3,542.85 26,217.09

Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved quality and

make, including painting of fittings and brackets, cutting and

making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a

15 mm CP Brass single hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder :

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

bracket of the same materials with snap fittings of approved

quality and colour, weighing not less than 105 gms.

Providing and fixing CP Brass 32mm size bottle trap of approved

quality & make and as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm

from wall face with concealed fittings arrangement of

approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body

push fit type WC pan connector of with integral single mould

MR sealing fins made of flexible EVA body to be fixed with 12 Each 900.00 0.00 10,800.00

manufacture supplied grease, including rubber bush / adaptor for

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto

1meter long with S.S. Triangular plate to european type W.C.

Of approved quality and make as approved by engineer in

Providing and fixing C.P. brass angle valve for basin mixer

18.53.1 and geyser points of approved quality conforming to IS:8931 20.00 Each 500.35 10,007.00

15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with

18.21.2.1 brass unions : 45 cm length , 15 mm nominal bore 25.00 Each 85.20 2,130.00

Providing and fixing PTMT soap Dish Holder having length of

18.65 138mm, breadth 102mm, height of 75mm with concealed fitting 12.00 Each 96.75 1,161.00

arrangements, weighing not less than 106 gms.

Providing and fixing of Infrared sensor controlled tap Battery

operation with external battery compartment and 4x AA alkaline

batteries including flexible hoses G 3/8 int. thread x 450 mm

with prefilter and flow regulator ; flow volume: max. 3.8 l/min

independent of pressure ; can be adjusted to 1.33 lpm (For

LEED) with additional areator 28 931 00 99 ; flow pressure: 0,5

- 5 bar ,max. resting pressure 8 bar (Model no. of 02 172 06 99

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement

and the cost of cutting chases and making good the same

including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the

43313 15 mm nominal dia Pipes 10 Mtr. 441.15 4,411.50

43314 20 mm nominal dia Pipes 15 Mtr. 513.75 7,706.25

43315 25 mm nominal dia Pipes 15 Mtr. 626.05 9,390.75

43316 32 mm nominal dia Pipes 20 Mtr. 712.75 14,255.00

Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste, and vent,

Type-B as per IS : 13592 suitable for rubber ring joints,

including all neccessary specials and fittings (confirming to

IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows,

cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in

concealed / inside duct / under floor & basement ceiling /

external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from

floor under false ceiling or embedding the pipes laid under floors

/ building in 75 mm. alround 1:2:4 cement concrete (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

including cost of shuttering for proper completion of the

work, breaking and making good the walls and floors etc. after

pipes have been duly laid and tested. The rubber ring shall

confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps

with nuts, washers etc on 50x50x5 mm slotted angle. The cost will

include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications

and as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 50 Mtr. 600 30,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 50 Mtr. 460 23,000.00

Providing and fixing PP white Trap with minimum 50mm water

MR seal with rubber seal on inlet to push fit hopper for indirect waste

110 mm inlet & 110 mm outlet Long ht 10 Nos 1505 0.00 15,050.00

Providing and fixing floor drain (FD) with 50mm outlet and

100 mm inlet having 19mm seal for indirect floor drain (FD).

Providing and fixing Multi Trap (MT) with 50mm outlet and

100 mm inlet having 19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet

fittings by fixing Tee 110 x50/110 x75 mm (as required)

MR fixed on 'P' traps for connecting fixture drains/ extension 10 Nos 850 0.00 8,500.00

pices in PP including fixing and sealing inlet joint with drip seal /

Pipe seal joint as required complete.

Electrical work includes replacing of electrical wires, Switch

6 sockets, LED lights etc. and wood work including doors,

window etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

1.7 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed steel conduit as required

1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 90 meter 327 29,430.00

1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 90 meter 369 33,210.00

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 40 meter 428 17,120.00

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

painting in case of surface conduit, or cutting the wall and making

good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the

1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 20 Each 156 3,120.00

1.24.5 6 pin 15/16 amp socket outlet 20 Each 197 3,940.00

Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with

1.27 Modular base & cover plate on existing modular metal boxes etc.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

2.3.2 8 way , Double door 2 Each 2573 5,146.00

Supplying and fixing following rating, double pole, (single

phase and neutral), 240 volts, residual current circuit breaker

2.14 (RCCB), having a sensitivity current upto 30 milliamperes in

the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

2.10.1 Single pole 70 Each 256 17,920.00

Supply, Installation, Testing and Commissioing of Recessed

downlightwith HPE (High- Performance Efficiency) with LED

(Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours;

energy-efficient LEDs, direct light emission, housing in die-

cast aluminium, Polyester powder white coloured coat applied

over a 5-stage pre-treatment trim, prismatic diffuser for

homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear, Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in

9.1 position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.25 Cum 131576.95 32,894.24

Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or

cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25

9.23 mm minimum depth on all edges of flush door shutters (over all 10 Sqm 401.4 4,014.00

area of door shutter to be measured).

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for

wooden doors Material : Stainless Steel. Finish : Satin Stainless

Steel (SSS). of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for

MR door thickness 25-50 mm for wooden doors of approved make 6 Each 930 0.00 5,580.00

and model all complete as per the direction of Engineer-in-charge.

Providing and Fixing FH-943 Double cylender Floor Spring-

for wooden door with Closing Force EN 3 with Maximum

door weight 105 Kg. Maximum door width 950mm.Closing

speed : 130° Final closing speed : 15-0°. Hold Open

(standard): 90° hold open. Weight of floor spring approx : 6kg,

5,00,000 cycles Tested with 5 Years Warranty against

manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom

MR Strap for wooden doors of approved make and model all 6 Each 1100 0.00 6,600.00

complete as per the direction of Engineer-in-charge.

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key

MR Hole for wooden doors of approved make and model all complete 6 Each 900 0.00 5,400.00

as per the direction of Engineer-in- charge.

Providing and Fixing ECY 1060- 60 mm SS Cylinder One

side knob and one side regular key (3 key) for wooden doors

of approved make and model all complete as per the direction of

Engineer-in-charge.

II NEW WASHROOM FOR OFFICERS -2 Nos of (1M+1F)

Demolition of existing walls, cabins and brick / block

masonry work & 12mm or more plaster as required

Dismantling of old plaster or skirting raking out joints and

15.56 cleaning the surface for plaster including disposal of rubbish to 50 Sqm 45.05 2,252.50

the dumping ground within 50 metres lead.

Dismantling/ chipping of concrete: Dismantling & chipping of

existing concrete up to 10 mm behind the main bar carefully by

low impact high frequency hammer without damaging the mother

concrete including cleaning the surfaces and preparing surface

ready to receive new plaster etc. at all height complete and

collecting and stacking of the debris at the lead of 50m at ground

floor in the premises as directed by Engineer in charge,

complete. The rates are inclusive of all materials, labor,

machinery, equipment, tools, tackles etc. and disposal of

debris into approved municipal dumping yards, all complete.

Half brick masonry with common burnt clay F.P.S. (non

6.13 modular) bricks of class designation 7.5 in superstructure above

plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 160 Sqm 1018.05 162,888.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

bars at every third course of half brick masonry.

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm

13.26 thickness over plastered surface to prepare the surface even and 160 Sqm 214.3 34,288.00

smooth complete.

Dismantling aluminium/ Gypsum partitions, doors, windows,

fixed glazing and false ceiling including disposal of

unserviceable material and stacking of serviceable material

with in 50 meters lead as directed by Engineer-in-charge.

Ceramic Wall tiles for toilets including painting and

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.60.1 Two or more coats on new work 101.39 Sqm 137.85 13,976.61

Providing and fixing metal system up to ceiling height,

which includes frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 GSM,

consisting of Boral U track 52mm wide having equal flanges

of 30mm and 0.55mm thick (Base metal thickness) fastened to

the floor slab and ceiling soffit using rawl plugs with screw at

MR-2 600mm centers, with first & last fixing point at not greater than 50.02 Sqmt 1500 0.00 75,030.00

50 mm from either end. Boral C studs 50mm wide having one

flange of 34mm, other flange 36mm, lip size 6 mm and 0.55mm

thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not

more than 610mm centers. Maintain 5 to 10mm gap between C

Stud and web of U Track.

Flooring of toilets includes water proofing and Marble

stone laying etc.

Providing and laying water proofing treatment to vertical and

horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of: (i) Ist course of applying cement slurry @ 4.4

kg/sqm mixed with water proofing compound conforming to IS

2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm

22.3 cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water 45 Sqm 774.25 34,841.25

proofing compound in recommended proportion including

rounding off junction of vertical and horizontal surface. (iii) IIIrd

course of applying blown or residual bitumen applied hot at 1.7

kg. per sqm of area. (iv) IVth course of 400 micron thick PVC

sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified and as directed

by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Supply, Installation, Testing & Commissioning of all toilet

fixtures including existing pipes.

Providing and fixing white vitreous china extended wall mounting

water closet of size 780x370x690 mm of approved shape

including providing & fixing white vitreous china cistern with

dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to

4 litre/ 8 litres),including seat cover, and cistern fittings,

nuts, bolts and gasket etc complete.

Providing and fixing stone slab with table rubbed, edges

rounded and polished, of size 75x50 cm deep and 1.8 cm thick,

fixed in urinal partitions by cutting a chase of appropriate width

with chase cutter and embedding the stone in the chase

with epoxy grout or with cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate 6 mm nominal

size) as per direction of Engineer-in-charge and finished

8.10.2 Granite Stone of approved shade 4 Sqm 3542.85 14,171.40

Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved quality and

make, including painting of fittings and brackets, cutting and

making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a

15 mm CP Brass single hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder :

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

bracket of the same materials with snap fittings of approved

quality and colour, weighing not less than 105 gms.

Providing and fixing CP Brass 32mm size bottle trap of approved

quality & make and as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm

from wall face with concealed fittings arrangement of

approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body

push fit type WC pan connector of with integral single mould

sealing fins made of flexible EVA body to be fixed with

manufacture supplied grease, including rubber bush / adaptor for

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto

1meter long with S.S. Triangular plate to european type W.C.

Of approved quality and make as approved by engineer in

Providing and fixing C.P. brass angle valve for basin mixer

18.53.1 and geyser points of approved quality conforming to IS:8931 10 Each 500.35 5,003.50

15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with

brass unions : 45 cm length , 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of

18.65 138mm, breadth 102mm, height of 75mm with concealed fitting 2 Each 96.75 193.50

arrangements, weighing not less than 106 gms.

Providing & Fixing of Grab bar 600 mm of non slipping

grip as per standard specification of use in disabled toilet

complete with brackets suitable for wall installation as per

approved sample complete in all respect.

Providing and fixing of Infrared sensor controlled tap Battery

operation with external battery compartment and 4x AA alkaline

batteries including flexible hoses G 3/8 int. thread x 450 mm

with prefilter and flow regulator ; flow volume: max. 3.8 l/min

independent of pressure ; can be adjusted to 1.33 lpm (For

LEED) with additional areator 28 931 00 99 ; flow pressure: 0,5

- 5 bar ,max. resting pressure 8 bar (Model

no. of 02 172 06 99 of Schell )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement

and the cost of cutting chases and making good the same

including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the

43313 15 mm nominal dia Pipes 25 Mtr. 441.15 11,028.75

43314 20 mm nominal dia Pipes 25 Mtr. 513.75 12,843.75

43315 25 mm nominal dia Pipes 22.21 Mtr. 626.05 13,904.57

43316 32 mm nominal dia Pipes 20 Mtr. 712.75 14,255.00

Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste, and vent,

Type-B as per IS : 13592 suitable for rubber ring joints,

including all neccessary specials and fittings (confirming to

IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows,

cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in

concealed / inside duct / under floor & basement ceiling /

external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from

floor under false ceiling or embedding the pipes laid under floors

/ building in 75 mm. alround 1:2:4 cement concrete (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

including cost of shuttering for proper completion of the

work, breaking and making good the walls and floors etc. after

pipes have been duly laid and tested. The rubber ring shall

confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps

with nuts, washers etc on 50x50x5 mm slotted angle. The cost will

include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications

and as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 600.00 12,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 460.00 9,200.00

Providing and fixing PP white Trap with minimum 50mm water

MR seal with rubber seal on inlet to push fit hopper for indirect waste

110 mm inlet & 110 mm outlet Long ht 2 Nos 1,505.00 0.00 3,010.00

Providing and fixing floor drain (FD) with 50mm outlet and

100 mm inlet having 19mm seal for indirect floor drain (FD).

Providing and fixing Multi Trap (MT) with 50mm outlet and

100 mm inlet having 19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet

fittings by fixing Tee 110 x50/110 x75 mm (as required)

MR fixed on 'P' traps for connecting fixture drains/ extension 2 Nos 850.00 1,700.00

pices in PP including fixing and sealing inlet joint with drip seal /

Pipe seal joint as required complete.

Electrical work includes replacing of electrical wires, Switch

6 sockets, LED lights etc. And wood work, doors etc as

Wiring for circuit/ submain wiring alongwith earth wire with the

1.7 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed steel conduit as required

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 20.00 meter 428.00 8,560.00

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

painting in case of surface conduit, or cutting the wall and making

good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the

1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 15.00 Each 156.00 2,340.00

1.24.5 6 pin 15/16 amp socket outlet 10.00 Each 197.00 1,970.00

Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with

1.27 Modular base & cover plate on existing modular metal boxes etc.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single

phase and neutral), 240 volts, residual current circuit breaker

2.14 (RCCB), having a sensitivity current upto 30 milliamperes in

the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supply, Installation, Testing and Commissioing of Recessed

downlightwith HPE (High- Performance Efficiency) with LED

(Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours;

energy-efficient LEDs, direct light emission, housing in die-

cast aluminium, Polyester powder white coloured coat applied

over a 5-stage pre-treatment trim, prismatic diffuser for

homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear, Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in

9.1 position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.12 Cum 131,576.95 15,789.23

Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or

cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25

9.23 mm minimum depth on all edges of flush door shutters (over all 5.00 Sqm 401.40 2,007.00

area of door shutter to be measured).

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for

wooden doors Material : Stainless Steel. Finish : Satin Stainless

Steel (SSS). of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for

MR door thickness 25-50 mm for wooden doors of approved make 2.00 Each 930.00 0.00 1,860.00

and model all complete as per the direction of Engineer-in-charge.

Providing and Fixing FH-943 Double cylender Floor Spring-

for wooden door with Closing Force EN 3 with Maximum

door weight 105 Kg. Maximum door width 950mm.Closing

speed : 130° Final closing speed : 15-0°. Hold Open

(standard): 90° hold open. Weight of floor spring approx : 6kg,

5,00,000 cycles Tested with 5 Years Warranty against

manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom

MR Strap for wooden doors of approved make and model all 2.00 Each 1,100.00 0.00 2,200.00

complete as per the direction of Engineer-in-charge.

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key

MR Hole for wooden doors of approved make and model all complete 2.00 Each 900.00 0.00 1,800.00

as per the direction of Engineer-in- charge.

Providing and Fixing ECY 1060- 60 mm SS Cylinder One

side knob and one side regular key (3 key) for wooden doors

of approved make and model all complete as per the direction of

Engineer-in-charge.

III WASHROOM CABINS FOR Sr. Env Eng

Demolition of existing walls, cabins and brick / block

masonry work & 12mm or more plaster as required

Dismantling of old plaster or skirting raking out joints and

15.56 cleaning the surface for plaster including disposal of rubbish to 50 Sqm 45.05 2,252.50

the dumping ground within 50 metres lead.

Dismantling/ chipping of concrete: Dismantling & chipping of

existing concrete up to 10 mm behind the main bar carefully by

low impact high frequency hammer without damaging the mother

concrete including cleaning the surfaces and preparing surface

ready to receive new plaster etc. at all height complete and

collecting and stacking of the debris at the lead of 50m at ground

floor in the premises as directed by Engineer in charge,

complete. The rates are inclusive of all materials, labor,

machinery, equipment, tools, tackles etc. and disposal of

debris into approved municipal dumping yards, all complete.

Half brick masonry with common burnt clay F.P.S. (non

6.13 modular) bricks of class designation 7.5 in superstructure above

plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 160 Sqm 1018.05 162,888.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

bars at every third course of half brick masonry.

13.4 12 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm

13.26 thickness over plastered surface to prepare the surface even and 160 Sqm 214.30 34,288.00

smooth complete.

Dismantling aluminium/ Gypsum partitions, doors, windows,

fixed glazing and false ceiling including disposal of

unserviceable material and stacking of serviceable material

with in 50 meters lead as directed by Engineer-in-charge.

Ceramic Wall tiles for toilets including painting and

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.60.1 Two or more coats on new work 101.39 Sqm 137.85 13,976.61

Providing and fixing metal system up to ceiling height,

which includes frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 GSM,

consisting of Boral U track 52mm wide having equal flanges

of 30mm and 0.55mm thick (Base metal thickness) fastened to

the floor slab and ceiling soffit using rawl plugs with screw at

MR-2 600mm centers, with first & last fixing point at not greater than 50.02 Sqm 1,500.00 0.00 75,030.00

50 mm from either end. Boral C studs 50mm wide having one

flange of 34mm, other flange 36mm, lip size 6 mm and 0.55mm

thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not

more than 610mm centers. Maintain 5 to 10mm gap between C

Stud and web of U Track.

Flooring of toilets includes water proofing and Marble

stone laying etc.

Providing and laying water proofing treatment to vertical and

horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of: (i) Ist course of applying cement slurry @ 4.4

kg/sqm mixed with water proofing compound conforming to IS

2645 in recommended proportions including rounding off junction

of vertical and horizontal surface. (ii) IInd course of 20 mm

22.3 cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water 40 Sqm 774.25 30,970.00

proofing compound in recommended proportion including

rounding off junction of vertical and horizontal surface. (iii) IIIrd

course of applying blown or residual bitumen applied hot at 1.7

kg. per sqm of area. (iv) IVth course of 400 micron thick PVC

sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick

11.55 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified and as directed

by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Supply, Installation, Testing & Commissioning of all toilet

fixtures including existing pipes.

Providing and fixing white vitreous china extended wall mounting

water closet of size 780x370x690 mm of approved shape

including providing & fixing white vitreous china cistern with

dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to

4 litre/ 8 litres),including seat cover, and cistern fittings,

nuts, bolts and gasket etc complete.

Providing and fixing stone slab with table rubbed, edges

rounded and polished, of size 75x50 cm deep and 1.8 cm thick,

fixed in urinal partitions by cutting a chase of appropriate width

with chase cutter and embedding the stone in the chase

with epoxy grout or with cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate 6 mm nominal

size) as per direction of Engineer-in-charge and finished

8.10.2 Granite Stone of approved shade 4.00 Sqm 3,542.85 14,171.40

Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved quality and

make, including painting of fittings and brackets, cutting and

making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a

15 mm CP Brass single hole basin mixer

Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder :

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

bracket of the same materials with snap fittings of approved

quality and colour, weighing not less than 105 gms.

Providing and fixing CP Brass 32mm size bottle trap of approved

quality & make and as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm

from wall face with concealed fittings arrangement of

approved quality and colour, weighing not less than 88 gms.

Providing ,Fixing of straight / offset type flexible single body

push fit type WC pan connector of with integral single mould

sealing fins made of flexible EVA body to be fixed with

manufacture supplied grease, including rubber bush / adaptor for

C.I pipe as supplied with the pan connector.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 :

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto

1meter long with S.S. Triangular plate to european type W.C.

Of approved quality and make as approved by engineer in

Providing and fixing C.P. brass angle valve for basin mixer

18.53.1 and geyser points of approved quality conforming to IS:8931 10.00 Each 500.35 5,003.50

15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with

brass unions : 45 cm length , 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of

138mm, breadth 102mm, height of 75mm with concealed fitting

arrangements, weighing not less than

Providing & Fixing of Grab bar 600 mm of non slipping

grip as per standard specification of use in disabled toilet

complete with brackets suitable for wall installation as per

approved sample complete in all respect.

Providing and fixing of Infrared sensor controlled tap Battery

operation with external battery compartment and 4x AA alkaline

batteries including flexible hoses G 3/8 int. thread x 450 mm

with prefilter and flow regulator ; flow volume: max. 3.8 l/min

independent of pressure ; can be adjusted to 1.33 lpm (For

LEED) with additional areator 28 931 00 99 ; flow pressure: 0,5

- 5 bar ,max. resting pressure 8 bar (Model

no. of 02 172 06 99 of Schell )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement

and the cost of cutting chases and making good the same

including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the

18.8.1 15 mm nominal dia Pipes 25.00 Mtr. 441.15 11,028.75

18.8.2 20 mm nominal dia Pipes 25.00 Mtr. 513.75 12,843.75

18.8.3 25 mm nominal dia Pipes 22.21 Mtr. 626.05 13,904.57

18.8.4 32 mm nominal dia Pipes 20.00 Mtr. 712.75 14,255.00

Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste, and vent,

Type-B as per IS : 13592 suitable for rubber ring joints,

including all neccessary specials and fittings (confirming to

IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows,

cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in

concealed / inside duct / under floor & basement ceiling /

external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from

floor under false ceiling or embedding the pipes laid under floors

/ building in 75 mm. alround 1:2:4 cement concrete (1 cement :

2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

including cost of shuttering for proper completion of the

work, breaking and making good the walls and floors etc. after

pipes have been duly laid and tested. The rubber ring shall

confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps

with nuts, washers etc on 50x50x5 mm slotted angle. The cost will

include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications

and as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 600.00 12,000.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 20 Mtr. 460.00 9,200.00

Providing and fixing PP white Trap with minimum 50mm water

MR seal with rubber seal on inlet to push fit hopper for indirect waste

110 mm inlet & 110 mm outlet Long ht 2 Nos 1,505.00 0.00 3,010.00

Providing and fixing floor drain (FD) with 50mm outlet and

100 mm inlet having 19mm seal for indirect floor drain (FD).

Providing and fixing Multi Trap (MT) with 50mm outlet and

100 mm inlet having 19mm seal for indirect Multi Trap (MT).

Providing, fixing, testing and commissioning of pipe inlet

fittings by fixing Tee 110 x50/110 x75 mm (as required)

MR fixed on 'P' traps for connecting fixture drains/ extension 2 Nos 850.00 0.00 1,700.00

pices in PP including fixing and sealing inlet joint with drip seal /

Pipe seal joint as required complete.

Electrical work includes replacing of electrical wires, Switch

6 sockets, LED lights etc. And wood work, doors etc as

Wiring for circuit/ submain wiring alongwith earth wire with the

1.7 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed steel conduit as required

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 20.00 meter 428.00 8,560.00

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

painting in case of surface conduit, or cutting the wall and making

good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the

1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 15.00 Each 156.00 2,340.00

1.24.5 6 pin 15/16 amp socket outlet 10.00 Each 197.00 1,970.00

Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with

1.27 Modular base & cover plate on existing modular metal boxes etc.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single

phase and neutral), 240 volts, residual current circuit breaker

2.14 (RCCB), having a sensitivity current upto 30 milliamperes in

the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supply, Installation, Testing and Commissioing of Recessed

downlightwith HPE (High- Performance Efficiency) with LED

(Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature

of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours;

energy-efficient LEDs, direct light emission, housing in die-

cast aluminium, Polyester powder white coloured coat applied

over a 5-stage pre-treatment trim, prismatic diffuser for

homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear, Protection class II, IP 40,

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in

9.1 position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.12 Cum 131576.95 15,789.23

Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or

cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25

9.23 mm minimum depth on all edges of flush door shutters (over all 5.00 Sqm 401.40 2,007.00

area of door shutter to be measured).

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle for

wooden doors Material : Stainless Steel. Finish : Satin Stainless

Steel (SSS). of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for

door thickness 25-50 mm for wooden doors of approved make

and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing FH-943 Double cylender Floor Spring-

for wooden door with Closing Force EN 3 with Maximum

door weight 105 Kg. Maximum door width 950mm.Closing

speed : 130° Final closing speed : 15-0°. Hold Open

(standard): 90° hold open. Weight of floor spring approx : 6kg,

5,00,000 cycles Tested with 5 Years Warranty against

manufacturing defect. CE certified for wooden doors all complete

as per the direction of Engineer-in-charge.

Providing and Fixing EFS ACC-001,002 top and Bottom

MR Strap for wooden doors of approved make and model all 2.00 Each 1100.00 0.00 2,200.00

complete as per the direction of Engineer-in-charge.

Providing and Fixing EDL 024 Dead lock Back set- 50 mm with Key

MR Hole for wooden doors of approved make and model all complete 2.00 Each 900.00 0.00 1,800.00

as per the direction of Engineer-in- charge.

Providing and Fixing ECY 1060- 60 mm SS Cylinder One

side knob and one side regular key (3 key) for wooden doors

of approved make and model all complete as per the direction of

Engineer-in-charge.

Total Prime Cost 4,554,248.00

DSR/ BOQ Unit Rate

S.No. DESCRIPTION UNIT Amount

MR Qty. (Rs.)

Supply, Installation, Testing and Commissioning of Customized

passenger lift of passenger capacity of 4Nos, including the

features like counter weight, safety switches, VFD Operated

and soft speed control etc

MR-2 Dismantling and constructing of base including civil works etc. 1 L.S 472000.00 472000.00

Total Amount 2,242,000.00

Total Amount 2,242,000.00

Digitally signed by AMIT

SR.NO ITEM DESCRIPTION QTY UNIT TOTAL

Supplying, Installation, Testing & Commissioning of 24

Ports 10/100/1000BASE- T PoE / PoE+ ports (Support

Persistent PoE) and 4 Combo 1G BASE-T/SFP ports, 1 x

RJ-45 Console Port, POE Budget 370 watt, IEEE

802.3az Energy Efficient Ethernet, IPv4 & IPv6 Static

Routing, 802 1P based QoS, Strict Priority,

Weighted Round Robin, Unicast / Broadcast &

Multicast Storm Control, Multicast: - IGMP Snooping v1,

v2, & v3, MLD Snooping v1 & v2, VLAN: - 802.1Q VLAN,

1 Voice VLAN, Q in Q VLAN, Management VLAN and 3 Nos 135000.00 405000.00

GARP, Access Control List (ACL), 802.1x

Radius/TACACS+ Authentication, Dynamic ARP

Inspection, IP Source Guard, DHCP Server Screening,

Digital Diagnostic Monitoring, LLDP / LLDP-MED, SSL

/ SSH, SNMP V1,V2,V3, All Switches and Fiber Modules

should be from same OEM. etc complete as reqd.

Supply, Installation, Testing and Commissioning of 24 U

Networking Rack , Front Glass Door Unit and Grilled back

door unit, lockable Door unit are steel, Powder Coated Rack

2 with Castors (4nos.), Fan (4 Nos.), Cable Manager (2Nos), 1 Nos 28000.00 28000.00

Full Tray Unit (1 Nos.), PDU (1Nos.) complete in all respect

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of 24 Port

loaded Jack Panel CAT 6A, Staggered 24 Port panel in 1U

Rack Unit, Copper Alloyed Contact Material, EIA 568A/B

3 wired, PC + glass fiber, UL 94V-0, black color, Front Port 2 Nos 5500.00 11000.00

Labelling, 22-24 AWG Wire Accumulation complete as

Supply, Installation, Testing & Commissioning of 1U PVC

Cable Manager is Ideal for Networking and Server Rack for

the better and effective management of cables

Supplying and drawing of CAT 6 U/UTP cable, white jacket,

1 4 pair LAN Cable in the existing surface/ recessed Steel/ 5000 Mtr 57.00 285000.00

PVC conduit as required.

Supply & Fixing of Dual Faceplate, Duplex Port (for data

and for voice) or as required square plate having spring

2 shuttered front access for preventing ingress of dust, 100 Nos 92.45 9245.00

dimension as per commercially available modular office

Supply, Installation, Testing & Commissioning of CAT 6

Infornmation Outlet,Universal label permits T568A or B

3 wiring, UL® Listed, meets all TIA and ISO 200 Nos 498.00 99600.00

requirements.Complete in all respect as required by the

Supply, Installation, Testing & Commissioning of CAT 6

1mtr,Patch Cord LSZH 1 Mtr, 4 pair 26 AWG stranded

copper wire, Pre-terminated with RJ45 plugs, Slim clear

4 anti-snag slip on boots, Suitable for EIA 568A or 568B 35 Nos 370.00 12950.00

wiring, UL® Listed, meets all TIA and ISO requirements.

Complete in all respect as required by site completion.

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of CAT 6

2mtr,Patch Cord LSZH 1 Mtr, 4 pair 26 AWG stranded

copper wire, Pre-terminated with RJ45 plugs, Slim clear

5 anti-snag slip on boots, Suitable for EIA 568A or 568B 35 Nos 430.00 15050.00

wiring, UL® Listed, meets all TIA and ISO requirements.

Complete in all respect as required by site completion.

Total Prime Cost 1,022,523.00

Digitally signed by AMIT