SPL REPAIR OF BLDG No. P-17/1 AND P-17/2 OF 24 GUARDS AT POKARAN MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.18 sqm n exc 0.36 sqm in floors,.set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed by Engineer-in-Charge.

M&L for Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles (300mmx 450mmx7 mm) in vertical surfaces jointed in neat cement slurry and pointed in white cement. Incl cutting the tiles to the required size whereven required incl mitring the corners etc over 10 mm thick backing coats of cement plaster in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Taking down existing doors/windows/ventilators (without taking off shutters and guard bars) of n exe 1.5 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down existing doors/windows/ventilators (without taking off shutters and guard bars) of exe 1.5 sqm & n. exc 4 sqm etc complete all as specified and directed by Engineer-in-Charge.

S&F standard aluminum sections of any Type as in doors, windows, ventilators, partitons etc, powder coated, cut to size, jointed with cadmium plated steel screws, including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), Nylon ball bearings and Unit rate quoted shall be deemed to include for sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window etc & aluminium beeds 20mm size and also including powder coated 150mm handle with built in locking system for each leaf complete all as specified. Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S&F 4.8 mm thick sheet glass, ordinary quality, in each pane for n exc 0.50 Sqm each pane for aluminium sliding windows/ventilator shutters etc complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etc complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed by Engineer-in-Charge.

S&F factory made Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and directed by Engineer-in-Charge.

M&L for IInd class Hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joint complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated with commercial face veneers etc complete all as specified and directed by Engineer-in-Charge.

S & F 30mm thick Glazed and ske- leton shutters, open rebated and prepared to receive glass, gauze, etc. with sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, cla-use 8.20 (a). etc complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel works including steel work in doors, grill etc complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new steel surface and applying two coats of synthetic enamel paint ovre a coat of red oxide primercomplete all as specified and directed by Engineer-in-Charge.

M&L for machine cut Granite (of any type) 20mm thick for kitchen platform over and including bedded and jointed with grey cement slurry/backing coat 15 mm thick in CM (1:6) and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types including demolition of Stone slabs and tiles of any description or thickness in floors laid bedded and pointed inany mortar , aprons etc. complete all as specified and directed by Engineer-in-Charge.

M & L for Machine cut kota stone slab flooring 20-25mm thick for window cill, jambs and sofits over and including cement screed base 20 mm thk in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including demolition of Stone slabs and tiles of any description or thickness in floors laid bedded and pointed inany mortar , aprons etc. complete all as specified and directed by Engineer-in-Charge.

M & L for rounding to edges of stone slabs on edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

S&F Butt hinges,100mm mild steel medium weight hinge pin complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handles cast type anodised 150mm size complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm size complete all as specified and directed by Engineer-in-Charge.

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of sextruded sections or cast aluminium alloy and fixed 300mm length complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces by applying two coats of synthetic enamel painting over one coat of pink primer on wooden surfaces exceeding 10 cm width or girthcomplete all as specified and directed by Engineer-in-Charge.

Dismantling of water tanks exc 500 & n exc 1000 ltr capacity and removing to store complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltrs capacity hoisted and fixed in position including 20mm dia float ball brass valve and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for re-fixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 20 mm bore including cleaning for re-fixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F CPVC pipes, SDR 11, 16 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all fittings such as Tee, bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and directed by Engineer-in-Charge.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all fittings such as Tee, bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated shower rose with or without swivel joints 75mm size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S/F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC with PVC telescopic pipe complete all as specified and directed by Engineer-in-Charge.

S &F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Bib taps, fancy type chromium plated with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Stop valves, fancy type chromium plated, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&Fin repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including Waste coupling of PTMT (half or full threaded) complete all as specified and directed by Engineer-in-Charge. Note :- Minimum weight 32mm- 45gms/40mm-60 gms including watse pipe of 40mm

S&F in repairs stainless steel kitchen plate rack of size 90cm X120cm X 1mm thick (18 gauge), complete all as specified and directed by Engineer-in-Charge.

Dismantling / taking down PVC/ Cast iron soil /waste pipes 100 mm / 75mm bore including all fitting like bends and fittings etc complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in floors or fixed to walls 75 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed to walls 110 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bends any radius 75 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75 mm complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick in cement mortar 1:6 on brick/stone work or concrete surfaces and finished even and smooth without using extra cement on walls complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick cement plaster in CM 1:4 using water proofing compound on brick/ stone surfaces finished fair and even without using extra cement etc complete all as specified and directed by Engineer-in-Charge. Note : Water proofing compound and will be measured and paid separately.

M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat of alkali resistance priming paint primer over 3mm thick wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-in-Charge. .

M&L for preparation of old painted surfaces including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss; efflorescent salts & trading oil, greasy spots and applying two coat of lime white wash on the ceiling etc complete all as specified and directed by Engineer-in-Charge. Note :- Rate inclusive of necessary scaffolding, trestels, ladders, cradles etc required for execution of work

M&L for complete removal of existing treatment of old painted wall surfaces and applying two coats of oil bound distemper over a coat of primer over 3mm thick wall care putty of approved make & shade on walls and other places complete all as specified and directed by Engineer-in-Charge. Note :- Rate including the required scaffolding & other accesories required for painting

Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position (PCC Padding over roof) complete all as specified and as directed by the Engineer-in-Charge.

M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC complete all as specified and directed by Engineer-in-Charge. Note :- WPC will be measured and paid separately as supply only

Supply only integral Water proofing compound complete all as specified and directed by Engineer-in-Charge. .

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced & Preparation of Surfaces of any description, over 10cm in width or girth Priming with Aluminium red oxide and Aluminium paint complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for levelling course for consolidated thickness 40mm as per the requirements complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of old painted steel surfaces of any description having execcding 10cm width or girth and applying two coat of synthatic enamel paint complete all as specified and directed by Engineer-in-Charge. Note :- Rate inclusive of necessary scaffolding and cradles for hoisting and lowering etc required for execution of work

S&F in repairs 20mm dia towel rail chromium plated 60cm long including bracket fixed with stainless screws complete all as specified and directed by Engineer-in-Charge.

Taking down cup board and wiremesh or panelled shutter of any description, Shutters of any description n exc 1 sq. m eacheach complete all as specified and directed by Engineer-in-Charge.

M&L for 18/19mm in repairs thick pre-laminated particle boards , interior grade , prelaminated both sides with decorative choice lamination fixed to timber frame-work with screwscomplete all as specified and directed by Engineer-in-Charge.

M&L for second class clean sawn hardwood in scantling fixed in timber framed work for cup board framecomplete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 75 mm size complete all as specified and directed by Engineer-in-Charge.

Cutting holes into or through brick/ stone walls built in cement mortar of superficial area n exc 150 Sq.cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed by Engineer-in-Charge.

S&F Rolled Mild Steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410 -W(Gde-E- 250)quality-A complete all as specified and directed by Engineer-in-Charge.

M&L for dismantling asbestos cement (corrugated micorrugatedetc.) sheet in roof covering/ fibre sheets etc complete all as specified and directed by Engineer-in-Charge.

S&F for Pre- Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium anodised, (fancy type) tubular curtain rod, 20mm dia, complete all as specified and directed by Engineer-in-Charge.

S&F in repair bracket aluminium anodised, (fancy type) for 20 mm dia tubular curtain rod(for item above) complete all as specified and directed by Engineer-in-Charge.

Demolition of stone masonry built in cement or cement lime mortar complete all as specified and directed by Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified and directed by Engineer-in-Charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type brought upto courses complete all as specified and directed by Engineer-in-Charge.

M & L for raised pointing to random or polygonal rubble to RR masonry, uncoursed or brought upto course in cement mortar 1:3 etc complete all as specified and directed by Engineer-in-Charge.

Rakesh Choudhary Contractor (BID ID -3157497)

Habib Traders (BID ID -3162645)