SPECIAL REPAIRS TO BLDG NO. OWT-75, OWT-76 AND OWT-77 (LIVING ACCN) AND CERTAIN REVENUE WORKS AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheet or Galvalume Steel Sheet of any gauge and thickness, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed.

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm Deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation Over Areas, not exc. 1.50 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation Over Areas, exc. 1.50 Metre but not exc. 3.00 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation Over Areas, exc. 3.00 Metre but not exc. 4.50 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, each not exc. 0.50 Cum, getting out including spread and levelled with excavated Surplus Soils, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Loose Filling with Aggregates of Broken Stone or Boulders, Gauge 80mm to 150mm in Sockage Pit, Sockage Well, etc., complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Roof Kerbs or Mud Stops, Rounded or Chemfered on Edges, Plinth/Licing/String Courses, Parapets and Railing upto 60 Cm in height, Copings, Kneelers, Apex Stones, Bed Plates, Kerbs, Holdfasts, etc. including necessary Formwork and Weathering, slightly Rounded or Chamered Angle and Throating, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Roof Beams, Lintel Bands, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement and Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Landings, Cover Slabs and Similar Articles with Plain Faces, Set in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Item.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in width, Set in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work One Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams and Similar Work; Square, rectangular or polygonal, Vertical or to batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned), Plain Fillets, Cleansawn, Square in Section, exc. 13.0 Sq Cm but not exc, 25 Sq Cm, fixed with Nails, complete all as specified and as directed.

S&F Flush Shutter 40mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Mild Steel Butt Hinge 100mm in size, medium weight, Cold Rolled and fixed, complete all as specified and as directed.

S&F Aluminium Handle 150mm long, Fabricated type, anodised, extruded and fixed, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixed-in-repairs, complete all as specified and as directed.

S&F Sheet Glass, 3.0mm thick Ordinary, Glazing in Metal or Wooden Frames and glazed with Oil Putty, not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections, fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), conforming to Fe-410-W (Gde E-250), Quality B, complete all as specified and as directed.

M&L Rolled Mild Steel in Main and Cross Beams, Hip and Jack Rafters, Purlin where connected to Common Rafters and Running Rails and Guides for Sliding Doors, fixed with Angle Cleats or Other Connecting Plates, conforming Fe-410-W (Gde-E250), Quality A, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F GI Powder coated GI Snap Grid Frame Work of size 605x605mm in False Ceiling, Exposed Suspended system, all as per Specifications & Drawing shown in MES Schedule, complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 6.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (40mm graded stone aggregate) 75mm thick in Floor, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Floors, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 25mm thick in Floors, etc., laid in Alternate Panels, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) 75mm thick in Plinth Protection, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured/Designer Tiles 7.0mm to 8.0mm thick (square/ rectangular) area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Machine Pressed Pre-cast Concrete Interlocking Paver Block, Coloured, Rubber Moulded, Glossy Finished, in any Shape and Size, having 60mm thickness of Concrete M-35 Grade, Coloured Glossy Finished, conforming to IS:15658-2006, laid over and including 50mm thick Sand Cushioning, complete all as specified and as directed. NOTE : Cost of Sand Cushioning will deem to be included in Quoted Unit Rate

M&L Machine Pressed Pre-cast Concrete 1:2:4 (20mm graded stone aggregate) Kerb Stone, finished at Top Bull Nosed Shape, finished Surface Even and Smooth and Jointed in Cement Mortar 1:6 Struck Finished including necessary Excavation and applying Two Coats of Synthetic Enamel Paint of Approved Tint, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick/PCC Blocks or Concrete Works including mixed with WPC, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Colour Wash over a Coat of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Surfaces by Complete Removal of Existing Treatment on Walls and applying Two Coats of Cement Based Paint with Approved Tint, complete all as specified and as directed.

M&L Preparing Surfaces by Complete Removal of Existing Treatment on Walls and applying Two Coats of Oil Bound Distemper with Approved Tint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Floors or fixing to Walls, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia), jointing with Solvent Cement, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) as Concrete Bed to Drain Pipes of 110mm bore (dia) including Packing Under and Haunching against the Sides of Pipes with Concrete after Pipes are Laid and Tested, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

M&L Cutting into existing Manholes for Connecting New Drain Pipes of 150mm (Internal dia), Making Good to Pipe and rendering, cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), smooth finished and reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fittings, etc., Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/out unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 20/25mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD with other Switches, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Casing Capping (ISI Marked) of size 25mm including all Fitting/ Fixtures such as Tee, Bend, Elbow, Socket, Saddles, etc. including Taking down /out Unserviceable PVC Casing Capping of any descriptions, complete all as specified and as directed.

S&F PVC Rectangular Block of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down /out Unserviceable Boards of any descriptions, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed.

S&F LED Bulk Head e-TATRA Series Light Fitting 1x6.0 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6.0 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Bulk Head Light Fitting of any description, complete all as specified and as directed. MAKE : C&S E-TARTA Series 6W or equivalent in Make : BAJAJ/ CG/ HAVELS/ PHILIPS as approved by GE.

S&F LED Decorative Wall Light Fixture 1x10 Watt made of Polycarbonate with LED 10 Watt Bulb and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down Unservice-able Light Fitting of any description, complete all as specified and as directed.

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt with LED 20 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Tube Light Fitting of any description, complete all as specified and as directed. MAKE : HAVELS E-Lite Pride Plus 20W or equivalent in Make : BAJAJ/ CG/ C&S/ PHILIPS as approved by GE.

M&L Taking down Ceiling Fan, Exhaust Fan of any Make, Size after disconnecting and Removing to AGE E/M Store Yard and deposited, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Hanging/Fixing only Ceiling Fan, Exhaust Fan and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure, Single Door with Steel Phosphotised Powder painted, SPN, 8-way, 240 Volt with 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELS, Cat No. DHDPSHOSRW08 or equivalent in LEGRAND/ L&T (as approved by GE).

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out Unserviceable Earthing of any description, complete all as specified and as directed.

M/S D G ENTERPRISE

FREEZCON

M/s Sashi Enterprise

kabitaconstruction