COMPREHENCIVE REPAIR TO POWER HOUSE, SUB STATION AND ALLIED WORK AT MILITARY STATION SRI GANGANAGAR

Amount

Dismantling brick tiles or terracing tiles, single layer on roof complete all as specified and directed by Engineer - in - Charge.

Demolation Mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by Engineer - in - Charge.

M&L for wire brushing and cleaning top surface of roof or cement concrete and applying evenly a tack coat of industrial bitumen 85/25@ 1.2 kg/ sqm complete all as specified and directed by Engineer - in - Charge.

M&L for Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg/ sqm complete all as specified and directed by Engineer - in - Charge.

M&L for 80mm thick lime concrete terracing as in roof all as specified in MES Sch part-I and part-II and directed by Engineer - in - Charge.

M&L for 40mm thick brick tiles laid on lime concrete & joint grouted flush in CM (1:3) mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed by Engineer-in-Charge.

Fixing only 40mm thick brick tiles laid on lime concrete & joint grouted flush in CM (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer-in-Charge.Note;- Serviceable tiles obtained Srl item No 01 shall be re-used

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) of any description complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete (1:4:8) type D-2, (40 mm graded stone aggregate) as in filling and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for 25mm thick cement concrete (1:2:4) type B-0, (12.5 mm graded stone aggregate) as in flooring finishing the surface even and smooth complete all as specified and directed by Engineer - in - Charge

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

M&L for 300mmx300mmx25mm thick chequered cement concrete tiles laid over and including 20 mm thick screed bed in CM 1:4 and set, jointed and pointed in neat cement slurry in floors with grey cement and pigments complete all as specified and directed by Engineer-in-Charge.

M&L for precast coloured rubber moulded concrete machine pressed concrete interlocking paver blocks any shape and size conforming to IS 15658-2006 of 60 mm thickness, M 35 grade wirh grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Scarifying and relaying existing loose course aggregate of size not exc 40 mm for depth n exc 15 cm and leveiling course aggregate complete all as specified and directed by Engineer - in - Charge.

Supplied and laying Graded coarse aggregate nominal size 40 mm spreading on floor of E/M installation depth n exc 15 cm deep to maintain the level as per electric norms complete all as specified and directed by Engineer - in - Charge.

M&L for 40mm thick cement concrete (1:2:4) type B-1, (20 mm graded stone aggregate) as in flooring finishing the surface even and smooth complete all as specified and directed by Engineer - in - Charge

M & L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graged stone aggregate) as in plinth protection complete all as specified and directed by Engineer-in-charge

S & F Glass dividing strips, 3 mm thick and width 38 mm inserted in position confirm to design complete all as specified and directed by Engineer-in-Charge.

Demoliton of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed by Engineer - in - Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L for brick work with sub class 'B' for continuous brick edging with width equal to the depth of the brick, laid on vertically including excavation of soil complete all as specified and directed by Engineer - in - Charge.

Taking down cement plaster on brick or concreate wall surfaces including racking out joints, hacking for key, scrubbing down with water etc. complete complete all as specified and directed by Engineer-in-Charge.

M&L 15 mm thick rendering in CM 1:6 on brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick rendering in CM 1:4 on brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 5 mm thick rendering in CM 1:3 on ceiling surfces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint, over a coat of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surfaces of ceiling and applying three coat of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coat of cement base paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old decorated plastered surfaces of ceilings by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spots and applying two coats of white wash complete all as specified and directed by Engineer - in - Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises,complete all as specified and directed by Engineer-in-charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exc. 0.11 sqm but not exc 0.18 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:6 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for glazed ceramic coloured tiles interior grade, of size 450x350x7mm thick as on vertical surfaces laid over and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M & L for 20 mm thick machine cut kota stone slab flooring laid over and including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 20 mm thick machine cut kota stone slab as in vertical surfces such as skirting, dados, laid over and including 10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings/ galvalume sheets/ aluminium sheets complete all as specified and directed by Engineer-in-charge

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

M&L for 0.63 thick plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc. 1.5 sqm but n. exc.4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) n. exc.1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc. 1 Sqm but n. exc 2 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc. 1 Sqm but n.exc 2 sqm each and refixing in the same opening / place complete all as specified and directed by Engineer - in - Charge.

Taking down steel windows & Ventilators (without taking off shutters from the frames) exc 1 Sqm but n.exc 2 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down carefully hood of steel rolling shutters, of any size description for replacement of unservicable/ defective parts and refixing in the same location, including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, complete, gear operated type with bevel gear box and crank handle size of shutter complete all as specified and directed by Engineer - in - Charge

S&F ball bearing for rolling shutters complete all as specified and directed by Engineer-in-charge.

Cutting holes in brick wall built in cement mortar for inserting holdfasts, depth of embedded portion exc half brick but n exc full bricks (measured from the face of jamb into the wall) and making good dismantled portion in cement mortor (1:3) or cement concrete (1:2:4) type B-I complete all as specified & directed by Engineer-in- charge.

S&F mild steel flat iron as in hold fast 25x6 mm conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer - in - Charge.

M&L for pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer - in - Charge.

M&L PCC 1:3:6 type C-1(20 mm graded aggregate) for filling of pressed steel frame and hold fast etc. complete all as specified and directed by Engr-in-charge.

S & F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

S & F Fiber Glass Reinforced plastic (FRP) Door Frames of required colour of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides, MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge

S & F 35mm thick, second class hard wood factory made, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers. complete all as specified and directed by Engineer - in - Charge.

S & F 35mm thick,Second class hard wood factory made wire glazed and skeleton door, window shutters open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing gauze/wire cloth, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specified and directed by Engineer - in - Charge.

S & F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required colour and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.complete all as specified and directed by Engineer - in - Charge.

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel,complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer - in - Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm the each pane complete all as specified and directed by Engineer - in - Charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge.

S & F butt hinges, heavy weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S & F butt hinges, heavy weight, cold rolled mild steel, and fixed of size 75mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S & F alluminium handle, cast type, anodised 150 mm long complete all as specified and directed by Engineer - in - Charge

S & F alluminium handle, cast type, anodised 125 mm long complete all as specified and directed by Engineer - in - Charge

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) & fixing clips of sheet, cast of extruded section and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy 300mm size complete all as specified and directed by Engineer - in - Charge

S&F alluminium anodised barrel tower bolts 150mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to window / ventilator with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge

S&F in repairs 300 mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed by Engineer - in - Charge

M&L for preparation of old painted wood and wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Taking down 15 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Fixing only Galvanised steel water tubing 15mm bore with new fitting including cutting chases to brick wall /ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 74 shall be re-used.

Taking down 20 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 20mm bore medium grade with all fittings and fixed to walls, ceiling or laid in floors etc complete all as specified and directed by Engineer-in-Charge.

Fixing only Galvanised steel water tubing 20mm bore with new fitting and fixed to walls, ceiling or laid in floorscomplete all as specified and directed by Engineer-in-Charge. Note;- Serviceable GI pipe obtained Srl item No 77 shall be re-used.

S&F in repairs 15mm bore stop cock / valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge. Make:- Parryware cat part no-T35011A1, Prayag cat part No- 8326, CREA cat part No. -F33002361

S & F in repairs 15mm bib tap cast copper alloy,fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8306, Parryware cat part no- T3504A1, CERA cat part no- HTF3001151

S&F in repairs 15mm bore angle stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge. Make:- Parryware cat part no-T35017A1, Prayag cat part No- 8310, CREA cat part No. -F3002201

S & F in repairs CP towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge

S&F in repairs , 20mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.Note:- Minimum weight 455gms

S&F in repairs grating doom 100 mm dia of PTMT complete all as specified and directed by Engineer-in-Charge. Note:- Minimum weight 25gms

S&F in repairs PVC connections 15mm size with PTMT nut of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, vitreous china wash hand basin white, flat back size 550x400mm including brackets, waste coupling 32mm dia of brass Chromium plated, 15mm dia pillar tap of cast copper alloy with capstan head screwed down, high pressure, with or without letter "Hot or Cold" with long screwed shank and fly nuts, 32mm dia, waste pipe low or high density polyethelene of pressure rating 6 Kg/Sqm and PVC connection with PTMT nuts of 15mm dia and 450mm long cutting for and pinning in end of brackets or erecting stand etc. complete all as specified and directed by Engineer - in - Charge.

S&F in repairs water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests and CI 'P' trap and proper connecting to flushing cistern complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC valve-less, syphonic action type flushing cistern 10 litre capacity Low level with inlet ball valve float, brackets and PVC flush L- pipe of 32mm dia bore complete all as specified and directed by Engineer-in-Charge. .

Dismantling and taking down water tank of capacity exc. 250 Litre but n. exc. 500 litre capacity complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded white colour polyethylene water storage tank 500 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres and white colour)

M&L writing letters or figures with synthetic enemal paint (Block, Roman, Italic or Indian) n. exc 30 cm high complete all as specified and directed by Engr-in-charge.

Cleaning away all grass vegetation, saplings, shrubs, brush wood, under growth, roots and trees n exc 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 meters outside the periphery of the area under clearance except in the case of surface dressing which includes for all the foregoing except clearing away of trees complete all as specified and directed by Engineer-in-Charge

Note : Notes : (i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

M/s Singla Trading Comapny

Ganganagar Enterprises