Job No.1088/2025 (HEW) Work for development of bal...

4.7.1.2 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10sqm on plan including getting out and disposal of excavated earth and lift up to 1.5 m, as directed by Engineer-in- Charge: 1.2 All kinds of soil 15 m lead

9.34.6 SHEET ROOFING Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 6 Gutter (600 mm over all girth)

4.12.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. 1 All kinds of soil

10.8 CEMENT CONCRETE FLOORING Providing and laying of conglomerate floor 40mm thick cement concrete topping 1:2:4

11.6.2 CEMENT PLASTER (IN FINE SAND) 15 mm cement plaster on the rough side of single or half brick wall of mix : 2 1:6 (1 cement: 6 fine sand)

10.30.2 TILE FLOORING Providing and laying of chequered precast cement concrete tiles 22 mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). 2 Medium shade pigment using 50% white cement 50% Grey cement.

11.25.1 POINTING ON BRICK WORK Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): 1 Flush / Ruled/ Struck or weathered pointing

13.29.2 SIGLE/BUILT-UP STEEL/TUBULAR SECTIONS Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required 2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

13.30.2 SIGLE/BUILT-UP STEEL/TUBULAR SECTIONS Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 2 Hot finished seamless type tubes

10.100.2 OTHER MISCELLANEOUS ITEMS USED FOR FLOORING 0 Cement Concrete 1:8:16 Flooring 2 Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth.

11.78 INTERIOR FINISHING Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.

17.8.1 Clearing and Grubbing Road Land . Compaction 1 Extra for laying earth/fly ash as per specifications in 20 cm layers and dressing but excluding the cost of rolling

7.20.2 BRICK WORK Brick work with common burnt clay modular bricks of class designation 10.5 in foundation and plinth in: 2 Cement Mortar 1:6 (1 cement : 6 coarse sand).

7.22.2 BRICK WORK Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 2 Cement mortar 1:6 (1 cement : 6 coarse sand)

30.24 FINISHING WORKS Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.

6.1.1 A CEMENT CONCRETE (CAST IN SITU) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

6.2.2 A CEMENT CONCRETE (CAST IN SITU) Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor four level, excluding the cost of centering, shuttering and finishing: 2 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

6.8.2 B DAMP-PROOF COURSE Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 2 40mm thick

6.14.2 D REINFORCED CEMENT CONCRETE Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 2 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

6.29.3 I CENTRING AND SHUTTERING (FORM WORK) Centering and shuttering including strutting, propping etc. And removal of form work for : 3 Columns, piers, abutments, pillars, posts and struts

6.39.1 K CEMENT CONCRETE PRECAST Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

3.1.2 Schedule A By Mechanical Transport including loading, unloading and stacking 2. Earth (Beyond 5km up to 10km per KM)

3.1.2 Schedule A By Mechanical Transport including loading, unloading and stacking 2. Earth (5km)

4.4.1 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5m 1 All kinds of soil

26.1 Supplying and stacking at site of work well-decayed farm-yard manure from any available source, approved by the Engineer-in-charge including screening through sieve of I.S.designation 16 mm with 5 km lead.

26.6 Maintenance of rough grassing, including 50 gm DAP and 50 gm Urea fertilizer application , watering and mowing etc for a period of one year.

26.13.4 Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farmyard manure (cost of well decayed farm yard manure to be paid separately) 4 Hole 0.60 metre dia and 0.60 metre deep

26.14 Horticulture and Land Scaping `Supplying and planting in prepared pits and watering, healthy , vigorous growing , permanent trees including ,application of 10 ml chlorpyriphos 20% EC, planting desired disease free, 200 cm to 220 cm height ,5 cm to 6 cm calliper size stem , full of foliage ornamental tree sapling each to be supplied in 30cm x 30cm poly bags,

26.18 Supply and planting of disease free healthy , vigorous growing more than 75 cm height permanent shrubs in already prepared pits, supplied in 25 cm x 20 cm poly bags , application of 10 ml chlorpyriphos 20% E.C. termiticide each and watering supplied through the tractor tanker.

26.58.1 Supply and installation of garden bench 1 Chair type garden bench with L-shaped sides made of reinforced concrete (M30), thickness 100 mm, overall height 1000 mm, base width 620mm. Back and seat shall consist of 5 Nos. reinforced concrete planks 1500 mm x 100 mm x 50 mm one plank 1500 mm x 200 mm x 50 mm. Seating height of the bench shall be 450 mm. The bench shall be fixed with nuts on concrete mount, all holes sealed after assembly and installation. All materials required to be as per BIS specifications.

26.76 Providing and fixing pair of Plastic dustbins 100 litre volume each, of two different colours, for dry and wet waste, made of virgin plastic to be mounted on MS rectangular hollow section 50 x 25 x 3 mm frames pivoted on 3 MS square hollow section verticals, 1 m above ground, one 35 cm RHS welded to each vertical member at base and grouted in 180 x 40 x 30 cm 1:2:4 cement concrete.

Job Work Analysis of rates fir earth cost or compensation for earth taken from private land completed in all respect (RM079)

Job Work Providing and fixing of children playing equipments (Chin swing, Slide sea-saw, Bridge Ladder and Merry GO Round) Complete in all repect. (Park No1 & 2) Providing and fixing chain swing of size 10' long x 9' high (above ground) frame is made of M.S. pipe 2" B class which stay with M.S. pipe 1" B class frame is connected with M.S. road 25 mm dia shaft having fabricated ball bearing no. 3204 shaft, further having 2 no. seating belt type seat welded with 8mm thick M.S. complete with painting and fixed in cement concrete block of size 12" x 12" x 15" into 4 legs in mixing of ratio 1:2:4. complete in all respect of entire satisfaction of engineer-in-charge. Providing and fixing of slide 12' long x 16" wide x 5' high (above ground) slide is made of S.S. sheet 18 SWG mounted on M.S. angle 40 x 40 x 4 mm slide 2 no vertical support of M.S. pipe 1" B class ladder having climbing steps of pipe 1/2 "B class complete with painting and to be fixed in Cc blocks 12" x12" x15" in to 4 legs of mix in ratio 1:2:4. Providing and fixing of setter sea -saw frame made of 2" Dia MS Pipe, 5" long and 1'-6' height of ground level with 4 Nos of Sea-Saw plunks with 1 1/2" MS Pipe, 8' long sheet made with 16 gauge painted with 1st quality paint and fixing with concrete block 1:2:4 ratio. Providing and fixing of bridge ladder high frame is of MS pipe 2" x 12 gage. Top hanging side pipe of MS pipe 2" x 12 gage and its climbing & center handles is of MS pipe 3/4" x 12 gage with priming and enamel spray painting in multy colour. Providing and fixing of Merry GO Round in position MGR platform made of 1.5" MS pipe with floor of 16 Guage MS sheet, Handrail 30" height made of MS pipe 1" with priming and enamel spray painting in multy color.

ved drawing) including transportation loading, unloading and fixing in 1:1½:3 CC block complete in all respect as per approved drawing and design) and up to the entire satisfaction of Engineer-in-charge. Triple Seated Twister:- Main round pipe 114 mod & 3.75 mm thickness M/s round pipe handle made of 31 mm round pipe. Round Plastic twisting plate 11" bearing system Twisting pipe 60 OD round smoothly working with rubber bearing system 114 mm pipe top S.S cover Plastic base cover and best quality Powder coating. Double Leg Press:- Main round pipe 114 mm od & 3.75 mm thickness M/s round pipe seat made of M/s sheet 16gauge size of seat is 12"X12" fixed on 48 OD Round pipe smoothly working with rubber bearing system all alloy covered with S.S cover Plastic base cover and best quality Powder coating.

Job Work Analysis for open GYM equipment's (10 Nos. Machines) complete in all respect (New) (Park No.3 & 4) Chest + Shoulder Combo :- Main pipe 114 mm OD & 3.75 mm thickness M/S Round pipe handles made of 38mm X 31 mm M/S Round pipe with Best Quality Rubber handle for hand grip working with rubber seal bearing system and foot rest main pipe for 60X40 mm M/S flat pipe size 6foot rest 5.5"X12"with base plastic cover all alloy cover with SS cover all M/S pipe best quality Powder Coating. Triple Air Walker:- Made of 114 mm od & 3.75mm thickness round pipe and 62 mm OD pipe made of 31 OD pipe size of foot rest14"X12" made of M/S sheet 16 gauge working smoothly with rubber seal bearing all alloy Cover with S.S cover and plastic cover on base best quality Powder Coating. Double Cross Trainer :- Main pipe 114 mm od & 3.75 mm thickness M/S Round pipe handles made of 38mm X31 mm M/S Round pipe with Best Quality Rubber handle for hand grip working with rubber seal bearing system and foot rest main pipe for 60X40 mm M/S flat pipe size of foot rest 5.5"X12"with base plastic cover all alloy cover with SS cover all M/S pipe best quality Powder Coating Double Ab Board :- Bed made of 31 mm round pipe and 20X40 mm M/5 flat pipe and joint with 114 mm M/5 round pipe with Plastic base cover and best quality rubber handles with Powder coating. Shoulder Builder:- Main pipe 114 mm od & 3. 75mm thickness 17" Round wheel made of 31 mm round pipe 25 mm round pipe with bearing system and S.S Nut cover with Plastic handle and U bend join with main 114 mm pipe for Steering wheel is 48 mm OD round pipe all alloy cover with S. S cover best quality plastic handle on wheels &base fixed with Nut bolt 8 mm M/S plate with plastic cover with best quality Powder Coating. Leg Press + Surf Board:- Main round pipe 114 mm od & 3.75 mm thickness M/s round pipe seat made of M/s sheet 16 gauge size of seat is 12"X12" fixed on 48 OD Round pipe smoothly working with rubber bearing system all alloy covered with S.S cover Plastic base cover and best quality Powder coating. Double Chest Press:- Made of 114 mm od & 3.75mm thickness 38 mm round pipe 48 mm round pipe S0XS0 mm Sq pipe complete Operating with bearing system with rubber seal bearing all alloy are covered the S.S covers & best quality Rubber handles for grip and smoothly working. Plastic base cover and best quality Powder coating. Cross Cycle:- Providing and fixing of cycling made with 3mm thick Galvanized pipe having main post 114mm/140mm, Auxiliary 60mm, 42 & 33 & 25x 50mm with aluminium /LLDEP post caps and plastic parts with stainless steel screws anti-UV, anti-heat, anti-aging, safe and eco-friendly having 200 to 250 Kg. user capacity with powder coated red, brown, blue paint an auxiliary with seed green & Steel grey paint (as per appro