Special Repair to Bldg No P149 Darshak Block at NIH Goa and Provision of 12 Nos stainless steel wind turbine roof ventilators in bldg No P23 and T 99 at NTRW G under GE Gomantak

Amount

M&L removing the existing treatment by brooming down with steel wire brushing scrapping down with steel scrapper and roughening the existing surfaces to receive plaster and cleaning of roof top complete all as specified and as directed. Note: The debris out the cleaning/removing/ scraping shall be removed out MD Land complete all as specified and as directed.

M&L for rendering/screed bed 10 mm thick on roof surface in cement mortar 1:3 mixed with liquid WPC @ 200 ml per bag of cement finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid seperately

M&L for laying water proofing treatment using 4mm thick APP modified membrane consisting five layers membrances with features as specified weighing not less than 3.5 kg per sqm reinforced with non woven polyester fiber @ 160gm/Sqm laid over a coat of cold applied bituminous primer @ 0.20 kg/sqm by torching the membrance and sealing the over lap by 100 mm length side and 150 mm width side all as per manufacturer instructions including joints and changes in direction be curved with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement curved well before laying membrance, all as per manufacturer instructions and applying two coats of bituminous aluminium paint @200 gm /sqm (minimum ) in two coat complete all as specified and directed. Note: (i) Irrespective of lap the net covered area will only be measured for payment. (ii) Rate is inclusive of APP membrane, SBR Latex

Removing loose concrete/plaster upto sound stratum of ceiling, chajjas, columns and beams and cleaned the surface with water using water jet etc. complete all as specified and directed

M&L apply one coat of Dr Fixit rust/De ruster or equivalent chemical as approved to old rusted reinforcement after necessary preparation of surfaces by brush application as per mistric 100 complete all as specified and directed.

M&L priming the old/new steel reinforcement bars by brush application with one coat of fosroc nito zinc primer of Dr. Fixit, epoxy zinc primer from sika or equivalent as approved .

S&F in repair Rotational moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), hoisted and fixed in Position all specified in MES Schedule Part-I, fixed with and including tank nipple, union and 20 mm diameter Ball brass valves high pressure with polythene float and fly nut screwed for iron pipe or brass ferrule and fixed as specified.

Taking up or down 15 mm dia steel tubing and connection and removal from site complete all as specified and directed

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified and directed

Taking up or down 25 mm dia steel tubing and connection and removal from site complete all as specified and directed

Supply, fixing, laying & testing CPVC pipes 16 mm outer dia SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Supply, fixing, laying & testing CPVC pipes 20 mm SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Supply, fixing, laying & testing CPVC pipes 25 mm SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S&F 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Taking down Chowkhats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including making good the wall surface complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each including making good the wall surface complete all as specified and directed.

S&F Powder coated (minimum 50micron) aluminium door/ window/ ventilators shutter and frame, any type sliding or openable & other similar work etc. fabricated by using the approved standard section including necessary arrangements to receive 4 mm thick glass or wire mesh with aluminium channel beading & stainless steel screws including the cost of rubber gasket/rubber beading etc. complete including necessary handles, roller wheels, hinges etc complete all as specified and as directed. Note :- (i) Weight of aluminium section shall be measured exclusive of all fittings fixtures, hinges, handle, bolts, rubber gasket/rubber beading and locking arrangements. (ii) Glass and wire mesh will be measured and paid seperately.

S&F aluminum powder coated deco grill make DG-104 (10 mm thick section) incl 'C/F/L' channel (weight not less than 0.136 g/Rm) alround grill complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and fixing with oil putty or rubber, wooden/aluminium beads and provsion of glazing pins where required in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F aluminium anodised wire mesh, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm fixed in in doors/window shutters with aluminium wire staples complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

M&L for providing factory made 25 mm thick 100% solid WPC (wood polymer composite) coloured laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powders/ rice husk/ wheat husk (non toxic additives, made from extrusion process WPC foam single extruded (inner) with having minimum density not less than 650 Kg/cbm, having good screw holding capacity (Screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance of spread of flame of class A category with Property of being Termite / borer free water / moisture proof and fire Retardant WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing with necessary full body threaded star headed counter sunk SS screw complete all as directed. Note :- Material test Certificate and authentication should be compulsory provided by the manufacturing company.

S&F second class hard wood plain solid straight chowkats frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 2nd class HW 35 mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 2nd class hard wood Kiln seasoned and chemically pressure treated glazed and skeleton factory made shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F butt hinges medium weight stainless steel 100 mm long (ISI marked) complete all as specified and directed.

S&F 150 mm long Aluminium handles, cast type (ISI marked) complete all as specified and directed.

S&F aluminium anodized, barrel tower bolt of extruded section, 150 mm (ISI marked) complete all as specified and directed.

S&F 300 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

S&F 200 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

S&F 100 mm long Aluminium handles, cast type (ISI marked) complete all as specified and directed.

S&F aluminium anodized, barrel tower bolt of extruded section, 100 mm (ISI marked) complete all as specified and directed.

Dismantling floor, hearth or wall tiling also in patches including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L glazed ceramic coloured tiles 350 x 250 x 6 to 7 mm/ 450x350x6 to7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles laid over and including 20 mm thick screeding in CM 1:6 complete all as specified

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking platforms and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 10 mm thick screed bed in CM 1:4 complete including rounding and polishing the edges all as specified and as directed.

M&L for Vitrified Ceramic tiles 9 to 10 mm thick light shade (also in patches) square/ rectangular polished, area of each tiles not exceeding 0.36 sqm as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Vitrified Ceramic tiles 9 to 10 mm thick light shade polished on vertical surface such as skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles laid over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F in repair Anglo Indian type viterous China wash down water closet pan (semi pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and including Plastic water closet seat cover white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern moulded from virgin poly propylene, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32 mm dia 90 cm long fixed properly to inlet of WC complete all as specified and directed

S&F in repair soap dish, brass chromium plated, oval shaped of size 100 x 50mm (approx), fixed to wall with PVC gully and CP screws complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550x 440 mm including two Nos angle iron brackets including 32mm dia brass CP waste coupling, waste pipe complete all as specified and directed

S&F in repairs 15mm dia Pillar taps, cast copper alloy, with long neck, chromium plated fancy type with aerator, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair stop valves 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed .

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair chromium plated brass shower rose 125 mm dia with or without swival joints, with CP long shank including fixing to 15 mm dia pipe or union all as specified.

S&F in repair 20 mm dia brass chromium plated tubular towel rail, D type, 60 cm long between flanges with hooks fixed with rawl plug complete all as specified and directed.

S&F in repair PVC connection 600 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed.

S&F in repair health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe superior quality with minimum 1 m long flexible pipe and ABS wall hook including making connections and fixed in position complete all as specified and directed. Make:- Agmeco/Sona/GEM/Kohler

S&F 18 mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination fixed with screws to timber frame work with Wooden beading of size 18mm x 6mm around open edges and varnishing / french polishing of beading complete as specified and directed.

S&F 18 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work with Wooden beading of size 18mm x 6mm thick around open edges and varnishing / french polishing of beading complete as specified and directed.

S&F continuous ( piano) hinges, mild steel , bright finish or electrigalvanised width of flaps (when opened) 30 mm complete as specified and directed.

S&F cast iron drawer pulls, 3 screw plate with fixed dished pull; 80 mm to 100 mm long complete all as specified and directed.

S&F 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 12 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work complete as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified.

M&L for Chisel the crack to a 'V' groove of 10mm X 10mm clean the groove to remove all loose laitance & wash with water and applying crack filler, Dr Fixit crack-X Paste/Dr Fixit crack X powder or equivalent with a putty blade.complete as specified and directed.

Taking down cement plaster on walls/ceiling of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete or stone surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying one coat of alkali resistant primer on plastered surfaces over 3mm thick Birla white wall care putty and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed.

M&L for complete removal of existance treatment of wall and applying two coat of oil bond distemper over one coat of alkali resistant primer over 3 mm thick wall care putty in two layers complete all as specified and directed

M&L 5 mm thick rendering in cement mortar 1:3 on ceiling or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new surface complete all as specified and directed.

M&L for complete removal of existance treatment of ceiling and applying three coats of white wash on ceiling including preparation of surface complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface or block masonary, 15 mm thick in two layers of 10 + 5 mm in CM 1:4 mixed with integral water proofing compound as per manufacturer instructions finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid seperately

Supply only liquid water proofing compound

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004 alkali and fungal resistance, dirt resistance exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 Sqm etc on newly prepared surface of brick (plastered or unplastered surface) or concrete surface complete all as specified. Note :- Second coat will be applied after first coat is completely dried i.e approximately 6-8 Hrs after applying of first coat.

M&L for complete removal of existing teatment and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004 alkali and fungal resistance, dirt resistance exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 Sqm etc on prepared surface of brick (plastered or unplastered surface) or concrete surface complete all as specified. Note :- Second coat will be applied after first coat is completely dried i.e approximately 6-8 Hrs after applying of first coat.

M&L for 100 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in base for fitment of water cooler and purifier equipments finished even and smooth without using extra cement complete all as specified and directed.

M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:4 complete all as specified and as directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light/fan fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 Sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings and replacement of modular metal flush box, modular white cover plate with frame, blanking plate and making good to the disturbed surfaces to match the existing complete all as specified and directed including 1.50 Sqmm nominal cross sectional area PVC (FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed. Note- (i) Rates include the cost of blanking plate, modular plate, modular boxes and covers of suitable modules as required at site. (ii) Modular box, plate and cover shall be of same make as of switch//socket/regulator.

All as per item No. 76 above but for one light point controlled by two Nos. two way switch

All as per item No. 76 above but for one 5 pin 5/6 Amp socket outlet point on same board

All as per item No. 76 above but for One bell/ buzzer point controlled by one bell push

All as per item No. 76 above but for one 5 pin 5/6 Amp socket outlet point on an independent board.

All as per Item No. 76 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 4 Sqmm and green colour earth cable of size 4 Sqmm.

S&F modular type switch one way 6 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type switch one way 16 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type bell push one way 6 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type socket 6 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F modular type switch two way 6 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type socket 6 Amp/16 Amps, 2/3 pin combined, 230 Volt, 2 Module complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50 mm dia complete all as specified and directed.

S&F modular type fan regulator, electronic stepped type, 230 Volt, 2 Module complete all as specified and directed.

S&F in repair modular type RJ 11 telephone socket, 1 Module complete all as specified and directed.

S&F in repair modular type coaxial cable television socket, 1 Module complete all as specified and directed.

M&L in replacement of Rigid non-metallic PVC conduit inclusive of boxes (junction/terminal), inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc 25mm external dia for telephone cable and TV socket concealed in wall by chases cutting all as specifeid and directed

S&F in replacement call bell, ding dong type, AC single pole, 230 volt complete all as specified and directed.

S&F in replacement MCB single pole 240 volts, 'C' curve of rating from 06 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB SPN 240 volts, 'C' curve of rating 40 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB TPN, 415 volts, 'C' curve of rating 63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement of MCB protected socket of 20 Amps with sheet metal enclosure including plug top 20 Amps complete with one single pole 240V with 20 Amps MCB "C" curve complete all as specified and directed. Make : Havells Cat Part No. DHDMCSN0251020 or equivalent in Legrand/ C&S/ Anchor

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection SPN, 240 Volts, 8 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection TPN, 240 Volts, 6 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 10 sqmm nominal cross sectional area and one run of 10 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 25 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 25 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in replacement existing U/S light fitting with LED tube light fitting surface mounted integrated type with 20 watt LED having minimum 100 lumens/watt electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed.

S&F in replacement existing U/S light fitting with LED tube light fitting surface mounted integrated type with 10 watt LED having minimum 100 lumens/watt electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed.

S&F brushless direct current (BDLC) ceiling fan 1400 mm sweep, 5 star rating complete with blades and other accessories, single phase, 230 V and making connection with sheathed 3 core cable of size 0.75 Sqmm flexible copper conductor wire including taking down old fan and deposited to MES store yard complete all as specified and directed.

S&F exhaust fan (Metal body) of 300 mm sweep, AC single phase 230/240 volts, heavy duty 1400 RPM complete with louvers including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan, grouting anchor bolts/fastners and making good to disturbed surfaces to match the existing including taking down old fan and deposited to MES store yard complete all as specified and directed.

S&F exhaust fan(Plastic body) of 250 mm sweep, AC single phase 230/240 volts, heavy duty 1400 RPM complete with louvers including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan, grouting anchor bolts/fastners and making good to disturbed surfaces to match the existing including taking down old fan and deposited to MES store yard complete all as specified and directed.

S&F in replacement of LED Bldg Security Street light 45W, IP 65 with suitable surge protection device including suitable size of GI pipe 1.2 m long bent to required shape, clamps, nut, bolts and making elecrical connection to the fitting with Suitable size of service wire. complete all as specified and directed.

M&L in replacament of existing old unsv earthing with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl. excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing complete all as specified an directed.

Taking down Split type AC of any capacity and kept in safe custody/ deposit MES Store till the completion of Bldg Work and refixing the same after servicing complete all as specified.

S&F in repair sub main wiring with four single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 16 sqmm nominal cross sectional area and one run of 16 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 40 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F static energy meter electronic tamper proof energy meter with backlite (LCD with multi features digital type) with optical communication port for down loading the data and two push buttons for manual depation to read the data, single phase two wire direct operated 240V, 50 Hz AC supply, class of accuracy 1.0 operating voltage 140 V to 300 V, AC range basic current 10 A maximum 60 A (10-60 A) conforming to IS 13779/CBIP 88 ISI marked with engineering plastic transparent pilfer proof meter box to house the single phase and class of protection shall not be less than IP 51, Dust & vermin proof, shock proof of suitable size to house meter freely complete all as specified and directed. Make :- L&T/ HPL/ SECURE

Dismantling/ cutting asbestos cement/ CGI/ Galvalume/ RCC Roof (Corrugated, Semicorrugated etc) sheets in roof covering etc complete all as specified and directed.

S&F for stainless steel wind turbine made up of SS-316 of turbine dia 60cm to 75cm, Nos of vanes 30-40, height between 40 cm to 55 cm and self driven with twin sealed 6000ZZ bearings and self lubricating bush of polyarride 66 resin to ensure friction less rotation even at lowest wind velocity, fixed with zero tolerance for leakages as specified and as directed

SACHINENTERPRISES