SPL REP TO SHAMSHER AUDITORIUM AT AF STN GORKAHPUR

Amount

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with subclass 'B' brick straight or curved on plan 6m mean radious built in CM (1:4) etc complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls/ concrete surface, etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15 mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished fair and even without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished fair and even without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling and finished fair even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed.

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick ( square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured of tiles including laying of screed bed or bedding layer of mortar 15mm thick in cm 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350 x250 x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tiles including rendering 10 mm thick on faces of brick or concrete surfaces in cm 1:3 complete all as specified and directed.

M&L for doublecharged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr in Charge.

Taking down door chowkats or frame n. exc 1.50 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down door chowkats or frame exc 1.50 sqm but n.exc 4 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter of any description n exc 1 sqm each each and removing from site complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, locks, strike plate etc complete and the size of frame is 125 x 60 mm complete all as specified and directed.

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, locks, strike plate etc complete and the size of frame is 105 x 60 mm complete all as specified and directed.

S & F factory made steel windows with side hung shutters (single frame with double shutter)inside gauzed and outside glazed including projection type hinges with steel handles and steel peg stay complete all as specified and directed with glazing bars dovetailed or welded.

S & F factory made steel ventilator with top hung shutters including hinges steel peg stay, guard bars 10mm sqare, MS bars welded @ 175 C/C horizontally etc complete all as directed.

S & F factory made flush shutters water proof BWR grade solid core construction with block board core and ply wood face panel commercial type both sides 30mm thick complete all as specified and directed.

M & L factory made IInd Class hard wood 35mm thickness Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factorymade solid pannel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with neat moulded plan colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on eithor side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the MS frame welded/sealed to the stiles, and rails with suitable PVC sheet bedding and jointed together with solvenet cement, supply and fixing in the frame at site as per specification as specified

S&F mild steel flat iron as in hold fast including screwing or welding complete all as specified and directed.

M&L provding cement concrete 1:3:6 using 20mm graded stone agg as in hold fast complete all as specified & directed.

S&F 75 mm size mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 150 mm long Aluminium anodized barrel tower bolt complete all as specified and directed.

S&F extruded aluminium anodized pressed handle, fabricated type of size 150mm complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed.

S&F in repair 1st class Hard Wood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc. complete all as specified and directed.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue with hard drawn steel spring with 140mm overall length of cover plate complete all as specified and directed.

S&F in repair stainless steel harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers but of anodised aluminium alloy etc complete al as specified and directed.

M&L for hacking out old broken glasses any thickness size, quality or description from metal frames including punching or drilling out old glazing pins / spring clips and providing and fixing new ones. hacking any bldg height complete all as specified and as directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

M&L for 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each panecomplete all specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for Joist, channel, angle, or tee sections, Fe 410 -W (Gde E- 250) quality A fixed independently, with or without connecting plates, etc complete all as specified and directed.

M&L for hot rolled steel flat Framed work of water tanks mesh welded and similar work conforming Fe 410 -W (Gde E- 250) quality A omplete all as specified and directed.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as spcified and directed.

S&F mild steel framed work such as grills, gratings, fillets etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars etc conforming to Fe 290, grade E-165 complete all as directed.

S&F for Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Demolition of cement concrete un- reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as specified.

M&L for screed bed or beding layer of mortar 20mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L Chequered cement concrete tiles with grey cement & pigment 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors all as specified and directed.

M&L 100mm thick PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in hard standing finished even and smooth without using extra cement including spike rolling to surface or making impression of expanded metal whilst the concrete is green complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound, Grade 'A' complete all as specified and directed.

Dismantling of false ceiling board ,fiber insulation board any thickness including wooden cover fillets aluminium frame work complete all as specified and directed.

Supply & Fixing of Knauf Fibre Glass Acoustical Suspended Ceiling System with 25 mm thick Optra Microlook 90 Edge Tiles with Knauf Suprafine 15mm face exposed grid.The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.85 – 0.95, Light Reflectance ≥88% as per ASTM E-1477, Colour Pebble White, Fire Performance of Class 0/1 as per BS 476 Part 6/7 with 15mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 1200 x 1200 x25mm. It shall be suitable for Green Building application, with Recycled content of 85%. The tile shall be laid on Knauf Suprafine 38 with 15 mm wide T - section flanges colour global white having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. Perimeter trim to be Knauf wall angles of size 3600x24x24mm, secured to walls using screws at 450mm centre to centre maximum. To ensure specification of tiles, Manufacturers Test Certificate is requiredhavingcomplete site address& duly signed by Manufacturer. Installation shall be carried out with the help of compatible suspension system, as per Knauf recommended procedure and designs as approved by the Architect/ Engineer-in-Charge.

Supply & Fixing tiled false ceiling of Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4 mm thick Diamond Textured (conforming to IS 14862; type B- Category III with Density >1200Kg/m3, MOR at EMC >10MPa and MOR in Wet Condition >8MPa, Thermal Conductivity K Value @50degree 0.20 W/mk, Fire Tested for Reaction to fire as per EN13501:Part 1 is A1-s1-d0, ASTM E84- 18b and as per BS 476 Part 4,5,6 & 7) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gsm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 24x38 mm made from 0.25mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 24x26mm made of 0.25mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x26mm made of 0.25mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.4 mm and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 4mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 24mm of all T -sections shall be pre-painted with polyester paint, all complete at all heights as per direction of Engineer-in-charge

Fixing oinly of Fibre Glass wool acoustical board as in wall panelling with 25 mm thick retrieved from exiting false ceiling under Item No 51 above, complete all as specified and as directed by Engineer-in-Charge.

Dismantling of brick tiles or terracing tiles single layer bedded in cement mortar on roof complete all as specified and directed.

Demolition of cement concrete in roof including plastering and leeping including cleaning surface of roof with wire brush / mechanical brush throughly to remove old dirt / loose particles to expose clean concrete slab clean with watering etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.50mm graded stone agg with WPC as in padding to maintain proper slope as required complete all as specified and directed. (WPC shall be paid separatly.)

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in roof kerb / benching in radius 10 cm with waterproofing compound as per manufacturer's instructions complete all as specified and directed.

M&L for cutting out cracks to V section in existing roof or terracing, cleaning out, wetting, grouting with cement and sand slurry in 1:3 complete all as specified and directed.

"Supply and Application of 5 Layer SHR Waterproofing Coating System as per manufacturer application procedure on leaking concrete roof surface by thorough surface preparation with high pressure water jet min. 125 bars, opening the cracks, followed by one absorption coat of nano-tech enhanced elastomeric waterproofing (NEEWP) emulsion having UV resistance and min. 50% solids, filling and sealing the cracks, then over coating with 2 Coats of NEEWP + Cement mixture as waterproofing coat having +450% Elongation. The surface is then to be tested for water tightness with a ponding test for min. 2 days and then top-coated with 2 Coats of SHR Coating - pure acrylic based, UV resistant, non-yellowing, bio-organism resistant (anti-fungal, anti-bacterial) conforming to BIS STD IS 17218:2019 with Pull off Adhesion 2.8 Mpa, passes 2000 hrs accelerated durability test, suitable for all types of cementitious surfaces, white colour, matt, surface coverage 3.25 SQM/Ltr/2 Coats, DFT 100 - 120 microns using brush, roller, airless spray gun as applicable. The product should be certified by NABL Approved Lab and application is to be done by company approved applicator only."

M& L prepaation of new plastered surface of wall and applying two coat of cement base paint over a coat of white cement primer and 2 mm thick BIRLA/JK Wall care putty in two coats (1mm+1mm) complete all as specified and directed

M & L for Preparing new plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & over a coat of alkali priming coat and 2 mm thick wall care putty in two coat (1mm+1mm) , complete all specified and directed

M & L preparation new plastered surfaces of any description , including cornices and applying three coats of white wash on ceiling by using mechanised euipments complete all as specified and as directed by Engr-in-Charge.

M&L for Washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of Oil Bound Distemper over 1mm thick wall care putty by using mechanised euipments complete all as specified and as directed by Engr-in-Charge.

M&L for Washing, rubbing down and stopping of distempered and painted surfaces of wall and applying two coats of cement base paint by using mechanised euipments complete all as specified and as directed by Engr-in-Charge. Note:- Cost of scaffolding and its removal is deemed to be included in unit rate quoted.

M&L for Washing, rubbing down and stopping of distempered and painted surfaces of old surfaces ceiling and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old painted wooden based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint by using mechanised euipments complete all as specified and as directed by Engr-in-Charge.

M&L preparation of old painted steel surfaces of any description, over 10cm width or girth and apply one coat of synthetic enamel paint by using mechanised euipments complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description, not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern, with EWC including p or s trap ,seat cover , including connection to trap /drain and to flushing pipe anti syphonage pipe etc complete including making good floorcomplete all as specified as directed.

S&F in repair vitreous chaina squating pan orissa pattern size 580X 440mm white with intregal foot rest complete including lime concrete(excl flushing cistern and flush pipe) but connecting to flushing pipe, anti-symphonage pipe etc complete fixed in repair complete all as specified as directed.

S&F in repair vitreous china ware wash hand basin 550mm x 400 mm size, white, flat back or angle including removing the existing one complete and refixing with new bracket and making good all connections.

S&F in repair vitreous china Urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) with urinal spreder complete all as specified and as directed by Engineer in Charge.

S&F in repairs 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and directed.

S& 15 mm bore pillar tap fancy type cast copper alloy chromium plated screwed down high pressure with or without lettered ' Hot' or 'Cold' with long screw shanks screwed for iron pipe or union complete.

Supply and fix in repairs 15 mm bore bib tap brass chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe fixed in repairs all as specified and directed.

S&F in repair, Bip taps (Long body), cast copper alloy (chromium plated) with crutch handle or butter fly handle, fancy type screwed down , screwed for iron pipe and fixed , complete all as specified and directed.

S&F in repair stop valves 15 mm fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair Concealed stop cock (fancy type),15 mm bore, chromium plated ,with long shank and cup complete all as specified and directed.

S&F in repairs cast copper alloy chromium plated caste copper alloy screwed high pressure with crutch or butter fly fancy type angle cock, of 15 mm bore complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair brass chromium plated shower rose 125mm size size fixed to pipe all as specified and directed.

S&F in repair Soap dish, vitreous China white, aprroximate size 160x 160x90mm complete all as specified and as directed.

S&F in repair PVC waste pipe 32mm dia for wash basin / urinal ISI marked complete all as specified and directed.

S&F in repair coloured toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and as directed by Engineer in Charge.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store up to complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store up to complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair CP Grating 125 mm size complete all as specified as directed.

Dismantling of water tanks of any type/pattern exc 500 ltr not exc 1000 Ltr and removing from site of work, complete all as specified and directed.

M&L for rotational moulded polythylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut , tank nipple as required complete, screwd for iron pipe or brass ferrule size 25 mm bore complete all as specified and directed.. Make:- Sintex/Rotax

S&F 15 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified.Make :- Prayag/ Polytuff

S&F in repairs 15 mm size Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floors complete all as specified and directed.

S&F for 110mm bore PVC (SWR) bends complete all as specified and directed.

S&F for 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floors complete all as specified and directed.

S&F for 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

M&L in repairs 100mm dia CI pipe including necessary repair to cement in wall/floor etc and making proper functioning of pipe lines jointing with cement mortar including taking down CI pipe with necessary brackets from wall/floor etc complete all as specified and directed.

S&F in repairs Cast iron bends/ tee etc of any radius, diminishing pieces or tapers 100mm bore size complete all as specified and directed.

Taking down carefully old and unserviceable sub main wiring of 2/3 runs of any size form any position and including making good disturbed surface of wall / ceiling etc complete all as specified and directed.

M&L for sub main wiring using 2 runs of single core FRLS PVC insulated and unsheathed stranded copper cable of size 1.5 sqmm cable (nominal area) of voltage rating 1100 V for phase and neutral, drawn in and including concealed PVC conduit of dia not less than 20mm dia with stranded accessories along with one run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 1.5 sqmm as earth continuity conductor all as specified and directed. (Note: 2 run of single core FRLS PVC cable 1.50 sqmm for phase & nuetral with one run of 1.50 sqmm earth conductor as earth shall be measured as one unit).

Taking down ceiling lights of any wattage alongwith accessories and refixing the same after execution of necessary repair work complete all as specified and directed.

Supply and fixing in replacement High Bay LED street light fitting 70 watt 230 V AC with high pressure diecast aluminium hosing and heat resistant complete with driver, with impact and corrosion resistent including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. Make: Syska Model No: SSK-HBG-70W

R.K.ASSOCIATES (BID ID -3112146)

M/S B.P. CONSTRUCTION (BID ID -3112296)

M/S EASTERN TECHNOCRAFTS (BID ID -3113048)

M/s Pandey Trading Company (BID ID -3112944)

DWARKESH STRUCT-CON (BID ID -3109971)

M/s RAAJSHREE INFRA (BID ID -3105745)

ANIRUDH ENTERPRISES (BID ID -3124822)