CERTAIN REPAIR TO FLOOR, PLUMBING JOINERY, PLINTH, MASONRY AND PERIODICAL AND OTHER B/R WORKS OF RESTRICTED AND UNRESTRICTED AREA OF COD UNDER GE (EAST) JABALPUR

UNRESTRICTED AREA

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises. Complete all as specified and directed.

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick in vertical surface such as dado / skirting / risers to steps etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4. Complete all as specified and directed.

M&L for Light Shade Vitrified Ceramic Tiles of design as approved 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for 75 mm thick Cement Concrete Type C2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection etc. & finishing cement concrete surface even and smooth without using extra cement. Complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed.

Taking up or down 15 mm bore of pipe steel tubing and connections, including cleaning for refixing or removal to store. Complete all as specified and directed.

Taking up or down 20 mm bore of pipe steel tubing and connections, including cleaning for refixing or removal to store. Complete all as specified and directed.

S&F in repair, Toilet paper holder with flat recessed type stainless steel. Complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. Complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane. Complete all as specified and directed.

S&F in repair, Urinal partition wall mounted, white colour of size 310 x 770 mm. Urinal partitions slabs terminating about 40 cm above floor line. Complete as specified and directed.

M&L for Cement Concrete Type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified and directed.

Taking down Shutters of any description area exceeding 1 sqm & not exceeding 2 sqm each and removing to store. Complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described & applying two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer. Complete all as specified and directed.

S&F in repair Stainless atell 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

S&F powder coated aluminium snap grid frame work for false ceiling with aluminium angle 25 mm x 25 mm x 1.5 mm fixed to perimeter of wall, main 'T' runner 38 mm x 25 mm x 1.5 mm and secondary/cross 'T' runner 25 mm x 25 mm x 1.5 mm to be interlocked in such a way that the size of grid shall be 605 mm x 605 mm including 6 mm dia GI hangers (upto 1200 mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40 x 3 mm, 60 mm long and expansion hold fasteners 12.5 mm dia , 40 mm long and 4 mm thick Non asbestos fibre board (E-board or V board) designer tiles (Electra) suitably fixed in false ceiling grid/frame with staples or screws complete all as specified and directed.

S&F MS hand rails, half round or other section for wind ties for roof including securing bolts; , drilling holes, notching all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3 mm (+- 0.2 mm). Window profile with hollow section with multi chamber. Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm). Sliding mesh Sash (42 mm x 57 mm), Sliding interlock (One vertical length in each shutters) (45.5 mm x 28 mm), Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, inclu

ding drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 +– 0.2 mm thick, galvanized steel Frame (30 mm x 18 mm) 02 nos, sliding sash (30 mm x 18 mrn), sliding mesh sash (26 mm x 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, [Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40 mm & required accessories.] (Note : The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.) (Area not exceeding 2.00 sqm each.)

S&F 5.5 mm thick sheet glass, ordinary quality, sheet glass is ground or obscured or frosted, on one side and glazing with oil putty in square but exc 0.5 sqm in each pane. Complete all as specified and directed.

S&F of Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165. Complete all as specified and directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. →

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,

S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification & drawing. Complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per specification and drawing. Complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetor

y windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/sqmm, modules of elasticity 900 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia & length complete as per direction of Engineer-in-Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately). Note : For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e., depth & width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum & screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/sqmm, modulus of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter & fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge. Note : Stainless Steel butt hinges & necessary S.S screws shall be paid separately.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size125x65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/sqmm, modules of elasticity 900 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia & length complete as per direction of Engineer-in-Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately). Note : For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e., depth & width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Dismantling boarding (Plywood) , any description , fixed in any position fixed with screw complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Chief.

M&L for 12 mm thick Pre-laminated particle board, interior grade, pre-laminated both side with decorative choice lamination, fixed with screws to timber frame work. Complete all as specified and directed.

S&F 100 mm long extruded aluminium alloy handles, fabricated type, anodised. Complete all as specified and directed

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed. Complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21. Complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy & fixed. Complete all as specified and directed.

S&F in repair, 18/19 mm thick, high density PVC/WPC solid fibre board with prelaminated PVC sheet as Kitchen cupboard and frame including taking down the old cupboard shutters and removing to store. Complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 40 mm. Complete all as specified and directed.

S&F magnetic catcher with nut and screw of mild steel bright finish. Complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for. Complete all as specified & directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

Dismantling Stone slabs & tiles of any description or thickness in floors, aprons etc., laid bedded & pointed in any mortar. Complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets. Complete all as specified and directed.

S&F powder coated GI snap grid frame work for false ceiling with aluminium angle 25 mm x 25 mm x 1.5 mm fixed to perimeter of wall, main 'T' runner 38 mm x 25 mm x 1.5 mm and secondary/cross 'T' runner 25 mm x 25 mm x 1.5 mm to be interlocked in such a way that the size of grid shall be 605 mm x 605 mm including 6 mm dia GI hangers (upto 1200 mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40 x 3 mm, 60 mm long and expansion hold fasteners 12.5 mm dia , 40 mm long and 6 mm thick Non asbestos fibre board (E-board or V board) designer tiles (Electra) suitably fixed in false ceiling grid/frame with staples or screws complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. Complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. Complete all as specified and directed.

Providing and fixing of G.I. metal framework made of 0.55 mm thick galvanized iron sections (having minimum 120 GSM zinc coating) consisting of perimeter channels, intermediate channels, and vertical studs fixed to wall for wall lining/wall panelling with dash fasteners and screws at spacing not exceeding 600 mm c/c, including all necessary fittings, leveling, and alignment complete all as specified and directed

M & L for applying one coat fire resisting paint on old painted wall Surfaces by description wood, steel, iron, concrete,brick, stone, etc., exceeding 10cm in width or girth complete all as specified and directed

Dismantling Plain or corrugated steel sheeting, any g

auge, thickness, including Nainital or similar pattern roof covering

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. ( Height of Bldg upto 12.50mtr)

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 2 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3) Allow 6-8 hrs time to dry the putty surface complete all as specified and as directed.

Material and labour for complete removal and preparation of old decorated treatment on wall by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two coats of oil bound emulsion distemper of approved tint including priming with alkali resistant primer complete all as specified and as directed.

Material and labour for complete removal of existing treatment for preparation of old decorated treatment on wall / ceiling / chajja by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint over a coat of weather proof primer with crack filling upto 5 bars of positive hydrostatic pressure on vertical walls without any dilution with forced coverage not more than 3.5 sqm / ltr as per manufacturer's instructions and all coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed. MAKE :- Apex Ultima Protek Asianpaints/ Nerolac excel top guard / Berger weathercoat long life 10

M&L for one coat of acrylic water based exterior grade primer @0.9 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio or as per manufacturer instruction with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and as directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:4 and to be finished even and smooth (without using extra cement). Complete all as specified and directed.

M&L 10 mm thick renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on RCC ceiling surface and finished even and smooth (without using extra cement). Complete all as specified and directed .

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying three coat of white wash Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coat of cement based paint over & including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coats of oil bound distemper over & including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of ceiling and apply three coat of white wash .Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying 2 mm thick Wall Care Putty on newly plastered or unplastered brick work or concrete surfaces. Complete all as specified and directed .

M&L for complete removal of existing Painted Surfaces& applying 2 mm thick Wall Care Putty on brick work or concrete surfaces or existing painted Surfaces. Complete all as specified and directed .

M&L for complete removal of existing Painted Surfaces & applying one coat of plastic emulsion paint including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for complete removal of existing Painted Surfaces &applying two coat of cement based paint including one coat of alkali resistant priming paint. Complete all as specified and directed.

M&L for preparation of putty Surfaces & applying two coat of oil bound distemper & including one coat of alkali resistant priming paint. Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying two coat of white wash . Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying one coat of cement based paint . Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying one coat of oil bound distemper . Complete all as specified and directed.

M&L for preparation of old painted ceiling surfaces & applying one coat of white wash . Complete all as specified and directed.

S&F in repair aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises. Complete all as specified and directed.

Per Quintal

M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick in vertical surface such as dado / skirting / risers to steps etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4. Complete all as specified and directed.

M&L for Light Shade Vitrified Ceramic Tiles of design as approved 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

M&L for 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for Cement Concrete Type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in sub base flooring average 25 mm thick surface finished even and rough (as in levelling course) to receive the topping layer. Complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick over & including 20 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing. Complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations. Complete all as specified and directed.

M&L for Hardcore of broken stone or boulders of gauge not exc. 63 mm, deposited, spread & levelled in layers not exc. 15 cm thick, watered & rammed to a true surface. Complete all as specified & directed.

M&L for 75 mm thick Cement Concrete Type C2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection etc. & finishing cement concrete surface even and smooth without using extra cement. Complete all as specified and directed.

M&L for providing Glass dividing strips, 3 mm thick and 38 mm width of strip in plinth protection for making panels. Complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed.

M&L for Non

Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank and removing to store. Complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank and removing to store. Complete all as specified and directed.

S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms). Complete all as specified and directed.

S&F ball valves for 25 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 455 gms). Complete all as specified and directed.

S&F in repair ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms). Complete all as specified and directed.

S&F in repair ball valves for 25 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 455 gms). Complete all as specified and directed.

S&F in repair PVC Tank cover for Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 or 1000 litre capacity fixed in position with nuts and bolt. Complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed in 15 mm bore dia of pipe. Complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed in 20 mm bore dia of pipe. Complete all as specified and directed.

Taking up or down 15 mm bore of pipe steel tubing and connections, including cleaning for refixing or removal to store. Complete all as specified and directed.

Taking up or down 20 mm bore of pipe steel tubing and connections, including cleaning for refixing or removal to store. Complete all as specified and directed.

Supplying & Laying of 20 mm Outer Diameter, CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors. Complete all as specified and directed.

Supplying & Laying of 25 mm Outer Diameter, CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors. Complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) of 15 mm bore of pipe. Complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) of 20 mm bore of pipe. Complete all as specified and directed.

M&L for Cleaning and removing all scale and dirt, etc., from RCC/PVC tanks exc 250 ltr & not exc 500 ltr capacity & from mouths of circulating pipes, etc. including washing of water tank with the use of Tank cleaning motor jet pressure machine and using bleaching powder & writing date of cleaning with any type of paint including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. complete all as specified and directed.

M&L for Cleaning and removing all scale and dirt, etc., from RCC/PVC tanks exc 500 ltr & not exc 1000 ltr capacity & from mouths of circulating pipes, etc. including washing of water tank with the use of Tank cleaning motor jet pressure machine and using bleaching powder & writing date of cleaning with any type of paint including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. complete all as specified and directed.

S&F in repair 15 mm bore, Fancy type, Chromoium plated Bib taps, cast aopper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. Complete all as specified and directed.

S&F in repair, Brass chromium plated Wall Mixer 3-in-1 System with provision for both Hand Shower & Overhead Shower complete with 115 mm long bend pipe, connecting legs & wall flanges (without Hand & Over Head Shower) for 15 mm bore of pipe. Complete all as specified and directed. Make-Jaquar Cat Part No.CON-281KN

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

S&F in repair, Brass chromium plated Sink Mixer with raised 'J' shaped swinging spout (Wall Mounted Model) with connecting legs & Wall flanges for 15 mm bore of pipe. Complete all as specified and directed. Make-Jaquar Cat Part No.CON-319KN

S&F in repair, Chromium plated Angular Stop Cock with wall flange for 15 mm bore of pipe. Complete all as specified and directed. Make-Jaquar Cat Part No.CON-059KN

S&F in repair, Chromium plated Two-way Bib Cock for 15 mm bore of pipe. Complete all as specified and directed. Make-Jaquar Cat Part No.CON-041KN

S&F in repair, 15 mm dia of bore, fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe & fixed. Complete all as specified and directed.

S&F in repair, 32 mm bore, brass chromium plated bottle traps for Wash basins with inlet & outlet screwed for pipe or connections including necessary packing, union & cap & fixed. Complete all as specified and directed.

S&F in repair, 32 mm bore, PVC waste pipe for Wash Basin/Kitchen Sink etc. Complete all as specified and directed.

S&F in repair, 32 mm bore dia of discharge pipe, waste coupling of PTMT (half or full threaded) (Minimum weight 32 mm-45 gms) etc. Complete all as specified and directed.

S&F in repair, 32 mm dia of bore, Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed. Complete all as specified and directed.

S&F in repair, Chromium Plated Grating, 100 mm dia with waste hole fixed on floor trap, nahani trap etc. Complete all as specified and directed.

S&F in repair, Toilet Seat/Commode Jet Spray (Regular Type) (1.50 meter) Stainless Steel Grade 304 (Built-in Installation Type) for 15 mm dia of bore of pipe. Complete all as specified and directed.

S&F in repair, Health Faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube & ABS wall hook including making connections & fixed in position complete in all respect as specified.

S&F in repair, Vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain & plug & porcelain stopper but including bracket & including supply & fixing of 32 mm dia of bore, brass chromium plated waste coupling. Complete all as specified and directed.

S&F in repair, Vitreous china wash down water closet pan (pedestal pattern), white, with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding fixing bolts, flushing cistern and flush pipe. Complete all as specified and directed.

S&F in repair, plastic water closet seat cover, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device. Complete all as specified and directed.

S&F in repair, Vitreous China squatting pan, ‘Orissa’ Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) etc. Complete all as specified and directed.

S&F in repair, Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm. Complete all as specified and directed.

S&F in repair, Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, ov

erall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm. Complete all as specified and directed.

S&F in repair, 1 mm thick, Stainless Steel Plate Rack of overall size 24 inch x 36 inch x 10 inch including fixing with rawal plug and screws. Complete all as specified and directed.

S&F in repair, 10 ltrs capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. Complete all as specified and directed.

S&F in repair, internal fitting for 10 ltrs capacity PVC valveless, syphonic action type flushing cistern. Complete all as specified and directed.

S&F in repair, flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for low level cistern. Complete all as specified and directed.

S&F in repair, 125 mm size, Brass chromium plated shower rose with or without swivel joints, including fixing to steel pipe or union. Complete all as specified and directed.

S&F in repair, PVC connections 15 mm size with PTMT nuts of length 450 mm. Complete all as specified and directed.

S&F in repair, Brass Chromium Plated, tubular towel rail, 20 mm dia, D type, 60 cm long between flanges etc. Complete all as specified and directed.

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed.

S&F in repair, Soap Dish Holder any type fixed to plug with chromoium plated brass screw. Complete all as specified and directed. Make-Jaquar Cat Part No.ACN-1311N

S&F in repair, Sheet Glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long. Complete all as specified and directed.

S&F in repair, Toilet paper holder with flat recessed type stainless steel. Complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. Complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane. Complete all as specified and directed.

M&L for Machine cut Kota stone slab 20-25 mm thick in riser of steps, skirting, dado & pillar over & including rendering 15 mm thick in 1:4 cement mortar, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing. Complete all as specified and directed.

S&F in repair, Diapory Rod, mild steel, chromium plated with fixing brackets, stops, rollers etc. Complete all as specified and directed.

S&F in repair, Floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm, with hard drawn steel spring, fixed in door. Complete all as specified and directed.

S&F in repair, Urinal partition wall mounted, white colour of size 310 x 770 mm. Urinal partitions slabs terminating about 40 cm above floor line. Complete as specified and directed.

M&L for Cement Concrete Type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified and directed.

Taking down Rain Water Pipe of any size or pattern including all fittings. Complete all as specified and directed.

S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. Complete all as specified and directed.

S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls. Complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius. Complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal. Complete all as specified and directed.

S&F in repair, 110 mm bore PVC (SWR) vent cowl. Complete all as specified and directed.

S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. Complete all as specified and directed.

S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls. Complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius. Complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal. Complete all as specified and directed.

S&F in repair, 75 mm bore PVC (SWR) vent cowl. Complete all as specified and directed.

S&F in repair, Stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, Including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe. Complete all as specified and directed.

S&F in repair, Stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, Including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe. Complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.50 sqm each with shutters (without taking off shutters from the frame) and removing to store. Complete all as specified and directed.

Taking down Chowkhats or frames exc. 1.50 sqm but not exc. 4 sqm each with shutters (without taking off shutters from the frame) and removing to store. Complete all as specified and directed.

Taking down Shutters of any description area exceeding 1 sqm & not exceeding 2 sqm each and removing to store. Complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, conforming to Fe-290 (Gde-E-165). Complete all as specified and directed.

M&L for Brickwork with old size flyash bricks, straight or curved on plan exceeding 6m mean radius, built in 1:6 cement mortar. Complete all as specified & directed.

S&F in repair Stainless atell 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification & drawing. Complete all as specified and directed.

M&L for Brickwork with old size flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:6 cement mortar. Complete all as specified & directed.

Dismantling boarding (Plywood) , any description , fixed in any position fixed with screw complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Chief.

M&L for 12 mm thick Pre-laminated particle board, interior grade, pre-laminated both side with decorative choice lamination, fixed with screws to timber frame work. Complete all as specified and directed.

S&F 100 mm long extruded aluminium alloy handles, fabricated type, anodised. Complete all as specified and directed

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed. Complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21. Complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy & fixed. Complete all as specified and directed.

S&F in repair, 18/19 mm thick, high density PVC/WPC solid fibre board with prelaminated PVC sheet as Kitchen cupboard and frame including taking down the old cupboard shutters and removing to store. Complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 40 mm. Complete all as specified and directed.

S&F magnetic catcher with nut and screw of mild steel bright finish. Complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for. Complete all as specified & directed.

S&F in repair, Brass chromium plated Wash Basin Mixer with raised 'J' shaped swinging spout (Table Mounted Model) with 450 mm long braided hoses for 15 mm bore of pipe. Complete all as specified and directed. Make-Jaquar Cat Part No.CON-319KNB or equivalent.

Dismantling Stone slabs & tiles of any description or thickness in floors, aprons etc., laid bedded & pointed in any mortar. Complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets. Complete all as specified and directed.

S&F powder coated GI snap grid frame work for false ceiling with aluminium angle 25 mm x 25 mm x 1.5 mm fixed to perimeter of wall, main 'T' runner 38 mm x 25 mm x 1.5 mm and secondary/cross 'T' runner 25 mm x 25 mm x 1.5 mm to be interlocked in such a way that the size of grid shall be 605 mm x 605 mm including 6 mm dia GI hangers (upto 1200 mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40 x 3 mm, 60 mm long and expansion hold fasteners 12.5 mm dia , 40 mm long and 6 mm thick Non asbestos fibre board (E-board or V board) designer tiles (Electra) suitably fixed in false ceiling grid/frame with staples or screws complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. Complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. Complete all as specified and directed.

Providing and fixing of G.I. metal framework made of 0.55 mm thick galvanized iron sections (having minimum 120 GSM zinc coating) consisting of perimeter channels, intermediate channels, and vertical studs fixed to wall for wall lining/wall panelling with dash fasteners and screws at spacing not exceeding 600 mm c/c, including all necessary fittings, leveling, and alignment complete all as specified and directed

M & L for preparation of applying two coat fire resisting paint on old painted ceiling Surfaces by description wood, steel, iron, concrete,brick, stone, etc., exceeding 10cm in width or girth complete all as specified and directed

Dismantling Plain or corrugated steel sheeting, any g

auge, thickness, including Nainital or similar pattern roof covering

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. ( Height of Bldg upto 12.50mtr)

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 2 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3) Allow 6-8 hrs time to dry the putty surface complete all as specified and as directed.

Material and labour for complete removal and preparation of old decorated treatment on wall by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two coats of oil bound emulsion distemper of approved tint including priming with alkali resistant primer complete all as specified and as directed.

Material and labour for complete removal of existing treatment for preparation of old decorated treatment on wall / ceiling / chajja by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint over a coat of weather proof primer with crack filling upto 5 bars of positive hydrostatic pressure on vertical walls without any dilution with forced coverage not more than 3.5 sqm / ltr as per manufacturer's instructions and all coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed. MAKE :- Apex Ultima Protek Asianpaints/ Nerolac excel top guard / Berger weathercoat long life 10

M&L for one coat of acrylic water based exterior grade primer @0.9 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio or as per manufacturer instruction with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and as directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:4 and to be finished even and smooth (without using extra cement). Complete all as specified and directed.

M&L 10 mm thick renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on RCC ceiling surface and finished even and smooth (without using extra cement). Complete all as specified and directed .

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying three coat of white wash Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coat of cement based paint over & including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coats of oil bound distemper over & including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of ceiling and apply three coat of white wash .Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying 2 mm thick Wall Care Putty on newly plastered or unplastered brick work or concrete surfaces. Complete all as specified and directed .

M&L for complete removal of existing Painted Surfaces& applying 2 mm thick Wall Care Putty on brick work or concrete surfaces or existing painted Surfaces. Complete all as specified and directed .

M&L for complete removal of existing Painted Surfaces & applying one coat of plastic emulsion paint including one coat of alkali resistant priming paint . Complete all as specified and directed.

M&L for complete removal of existing Painted Surfaces &applying two coat of cement based paint including one coat of alkali resistant priming paint. Complete all as specified and directed.

M&L for preparation of putty Surfaces & applying two coat of oil bound distemper & including one coat of alkali resistant priming paint. Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying two coat of white wash . Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying one coat of cement based paint . Complete all as specified and directed.

M&L for preparation of old painted brick work or concrete surfaces & applying one coat of oil bound distemper . Complete all as specified and directed.

S&F in repair, Soap Dish Holder any type fixed to plug with chromoium plated brass screw. Complete all as specified and directed. Make-Jaquar Cat Part No.ACN-1311N

S&F in repair, Harrison rails,/drapory mild steel, chromium plated with fixing brackets, stops, rollers etc. Complete all as specified and directed.

Providing & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum & screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/sqmm, modulus of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter & fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge. Note : Stainless Steel butt hinges & necessary S.S screws shall be paid separately.