MODIFICATION AND IMPROVEMENT TO TOILETS IN CERTAIN MARRIED ACCOMMODATION AND PROVN OF ROAD FURNITURE AND ASSOCIATED WORKS AT HQTC BANGALORE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-charge.

Material and labour for 25mm thick PCC 1:2:4, type B0 (Using 12.5mm graded stone aggregate) as in flooring, rough finish surfaces for receving top layer complete all as specified and as directed by Engr-in-charge.

Material and labour for coloured non skid ceramic tiles joint free of any shade/ pattern/design 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floors etc., set and jointed in neat cement slurry over and including 15mm thick screed bed of cement mortar 1:6 and pointed with white or coloured cement to match complete all as specified and as directed by Engr-in-charge.

Material and labour for coloured glazed ceramic design tiles joint free of any shade/ pattern/design 300x400x7mm/ 450x350x7mm thick, on vertical surfaces such as skirting, dado's and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Material and labour for granite (of any type) tiles 18-20mm thick (table rubbed and polished) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone in as in flooring and landings of stair case, treads including cutting and polishing of tiles and 20mm thick screed bed of cement mortar 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, cill and other similar situations complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-charge.

Sunken Waterproofing Surface Preparation: Taking out/ down old existing sunken slab treatment and cleaning the old RCC surfaces of sunken /lowered portion of slab surface for full depth of sunken floor by wire brush or chisel out any mortar sticking the surface including cleaning and preparation of the substrate to receive Fosroc Polyurea water proofing system shall be a sound base free from any oil, grease, rust, or deleterious material which may impair adhesion. The surface preparation shall be carried out mechanically to remove contaminants, laitance and weak concrete, to expose blow holes, and to produce a sound concrete with adequate profile and porosity. Any crack shall be treated with cementitious repair mortar of Fosroc Renderoc CS or epoxy crack filling mortar or equivalent product by proper grooving arrangement complete all as specified and as directed by Engr-in-charge.

Bore Packing (for Reinstallation): Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore using suitable arrangement (depending upon site conditions). Applying a coat of styrenebutadiene based polymer coating using Nitobond SBR or equivalent product of Asian paints, M/s MC Bauchemic /CIPY/SIKA/Pidilite Dr Fixit/ Thermax/ STP admixed with integral WPC or cementitious crystalline waterproofing compound to enhance adhesion between the packing material and other surfaces. Packing the gap using nonshrink cement polymer-based grout using conbextra GP2 upto the surface of the bore whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive strength at 28 days as per BS-1881 45 N/mm2 complete all as specified and as directed by Engr-in-charge.

Coving treatment: Making coving of 50x50mm at all the flat and vertical junction using Fosroc Renderoc Single component, shrinkage compensated, fiber reinforced, thixotropic cementitious mortar, to achieves a minimum compressive strength of 20 MPa in 1 day and 55 MPa in 28 days when tested as per EN 12190 and capable of applying 50mm thickness in single layer of approved product finished flush with existing surface complete all as specified and as directed by Engr-in-charge.

Waterproofing membrane: Supply and application of single-component, Pitch free seamless roller/ spray applied Nitoproof 600PF or equivalent product of Asian paints, M/S MC Bauchemic/ CIPY /SIKA /Pidilite Dr Fixit / Thermax/ STP applied at average minimum DFT of 1.3mm above primed surface with Nitoproof WB Primer or equivalent product of Asian paints, M/S MC Bauchemic/ CIPY /SIKA /Pidilite Dr Fixit/ Thermax/ STP It shall possess the following properties: Solids by Volume: 85%, Tensile Strength ASTM D412: >1.9 MPa, Tear resistance ASTM D624C: 15(N/mm), Elongation ASTM D-412: >400%, Adhesion in-peel test ASTM C836 (N): > 50N complete all as specified and as directed by Engr-in-charge. Notes: (i) Providing a non-woven geotextile fabric of 200GSM over the cured waterproofing membrane before going for a protective layer. (ii) Fill the sunken with water and check for dampness and seepage. All pipes passing through walls of sunken floor shall be laid before water proofing treatment is carried out. One No 50mm dia, 35mm long medium grade GI pipe with wire gauge on inside mouth shall be provided to each sunken portion. Cost of pipe with including of quoted rate, no extra cost will paid. (iii) The work shall be carried out complete as per manufacture's specifications and application methodology. Execution to be done with authorized trained/ skilled applicator with prior experience of more than 5 years in applying similar system and as per manufacturer technical guidelines laid by manufacturer.

Taking down of chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frames) and set aside or removing from site complete all as specified and as directed by Engr-in-charge.

Taking down of chowkats or frames exc 1.5 sqm but not exc 4 sqm each (without taking off shutters from the frames) and set aside or removing from site complete all as specified and as directed by Engr-in-charge.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and as directed by Engr-in-charge.

Material and labour for PCC 1:2:4 type B-0 (Using 12.5mm graded stone aggregate) as in hold fast blocks, for pressed steel frames filling, etc., including necessary formwork, moulds etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for factory made solid PVC moulded door shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specification complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old painted surface of any description not otherwise described steel and iron surface over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-charge.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc., under 40 sqcm in section, in unframed work, in any position complete all as specified and as directed by Engr-in-charge.

Material and labour for 2nd class hard wood plain fillets, square, rectangular or triangular, not exc 3 sqcm in section, clean sawn, secured with nails or brads complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of untreated new wooden surface of any description not exc 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed by Engr-in-charge.

Material and labour for 30mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-charge.

Supply and fix for 35mm thick 2nd class hard wood glazed and skeleton shutter as in door open rebated and prepared to receive glass, gauge etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in SSR part-I, Sec-08, Clause 8.24(a), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of untreated new wodden surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engr-in-charge.

Supply and fix for 100mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-charge.

Supply and fix for 200mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 150mm aluminium handles, cast type anodised complete all as specified and as directed by Engr-in-charge.

Material and labour in repair for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 height complete all as specified and as directed by Engr-in-charge.

Material and labour for reparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Taking down rain water pipes including all fittings any size and pattern upto 10th storey floors complete all as specified and as directed by Engr-in-charge.

Material and labour for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-charge.

Material and labour for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-charge.

Material and labour for 150mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls as rainwater pipe complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 75mm dia PVC bends with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 110mm dia PVC bends with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 150 mm dia PVC bends with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 110mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 75mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 110mm dia vent cowl complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal with access door complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engr-in-charge.

Dismantling water tanks exc 500 ltrs and not exc 1000 ltrs complete all as specified and as directed by Engr-in-charge.

Supply, hoisting, fixing in position and connecting incoming and outgoing pipes, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), triple layer, including dismantling existing water tank complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 25mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and as directed by Engr-in-charge.

Taking up or down 15mm dia steel tubing connections, including cleaning for re-fixing or removal to store complete all as specified and as directed by Engr-in-charge.

Taking up or down 25mm dia steel tubing connections, including cleaning for re-fixing or removal to store complete all as specified and as directed by Engr-in-charge.

Supplying and laying of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, outer diameter of pipes in 16mm complete all as specified and as directed by Engr-in-charge.

Supplying and laying of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls /ceiling or laying in floors, outer diameter of pipes in 20mm complete all as specified and as directed by Engr-in-charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, lintels, etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cms girth in brick walls complete all as specified and as directed by Engr-in-charge.

Supplying and laying of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls /ceiling or laying in floors, outer diameter of pipes in 32mm complete all as specified and as directed by Engr-in-charge.

Supply and fix for brass elbow for CPVC pipes SDR 11 and plain CPVC SDR 11 with special fittings for hot water only complete all as specified and as directed by Engr-in-charge.

Supply and fix for brass Tee for CPVC pipes SDR 11 and plain CPVC SDR 11 with special fittings hot water only complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-charge.

Material and labour for applying a coat of blown industrial bitumen of grade 85/25 or 90/15 applied hot to concrete, wall surfaces @ 1.2Kg/Sqm or as required including cleaning the surfaces complete all as specified and as directed by Engr-in-charge.

Material and labour for shower panel Jaquar Curve Neo Shower Panel 1500x230mm white Almunium Finish Code SHP-WHT-TMCURVENEO complete all as specified and as directed by Engr-in-charge.

Material and labour for rimless single piece WC with PP soft close slim seat cover, hinges, dual flush cistern fittings, fixing accessories and accessories set, size of EWC 370x665x750mm, S Trap-220mm complete all as specified and as directed by Engr-in-charge.

Material and labour for bathroom vanity set with WHB size 710x450x200mm, water proof cabinet size of 680x440x400mm, looking mirror size of 700x500 mm and side cabinet size of 250x150x700mm of Code no- PZV 838 Make- Prizma any design or shade complete all as specified and as directed by Engr-in-charge.

Material and labour for venetian image LED bathroom mirror with light, antifog backlit design, touch control, dimmable lighting (Three Colour), horizontal /vertical wall mount modern bathroom decor (Size of Mirror 40 inches L x32 inches W) and fitting of any design or shade complete all as specified and as directed by Engr-in-charge.

Material and labour for single lever basin mixer and fittings complete all as specified and as directed by Engr-in-charge. Make: Code No. LYR -CHR- 38001B of Jaquar or techno commercially equivalent model in Parryware/ Cera/ Prayag/ Somany

Material and labour for angle valve with wall flange chrome finish and fittings complete all as specified and as directed by Engr-in-charge. Make: Code No. OPP-CHR-15053PM of Jaquar or techno commercially equivalent model in Parryware/ Cera/ Prayag/ Somany

Material and labour for metal crome towel ring with round flange (medium) size of towel ring 200mm dia chrome finish and fittings complete all as specified and as directed by Engr-in-charge.

Material and labour for metal crome towel rack 600mm long with lower hangers chrome finish and fittings complete all as specified and as directed by Engr-in-charge.

Material and labour for metal crome towel rack 450mm long with lower hangers chrome finish and fittings complete all as specified and as directed by Engr-in-charge.

Material and labour for flexible hot and cold heavy duty PVC connection pipe 18 inch long (set of 2 nos) 304 stainless steel braided outer tube and EDPM inner tube, 2 pieces of silica gel prevent leakage and copper inner joint complete all as specified and as directed by Engr-in-charge.

Material and labour for orchids concave mirror 86x110x110mm refill capacity 150 pills x 2 Ply. Stainless steel body, two sided mirror, 360degree swivel, wall mounted and 5 x magnification complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs corner glass shelf, 300x300mm fancy type complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs corner glass shelf, 230x230mm fancy type complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs PVC body cabinet box mirror of size 350x450x100mm in PTMT alloy of approved patterns and designs complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed with and including chromium plated brass screws and wooden /plastic cleats complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs standard PVC waste pipe 32mm dia for WHB complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 32mm dia waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 100mm dia stainless steel gratings without hole /with hole of minimum weight 50 gms complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 40mm dia PVC pipe all necessary fittings on walls /floor or laying in floors, outer diameter of pipes in 32mm complete all as specified and as directed by Engr-in-charge.

Supply and fix 40mm dia PVC elbow complete all as specified and as directed by Engr-in-charge.

Supply and fix 40mm dia Tee complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs single lever cast copper alloy, chromoum plated hot and hold 15mm dia fancy type wall mixer complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type CP 2-way bib cock with wall flanges complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 15mm bore chromium plated fancy type long body bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs vitreous china ware wash hand basin white, flat back, size 550x400mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs PVC flushing cistern 10 ltrs capacity valveless syphonic action type low level, white, with inlet, ball valve float and handle including brackets and flush pipe complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs PVC connection 15mm size 450mm long with CP PTMT nuts complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type 15mm bore angle stop valves, chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type 15mm bore concealed cock, chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-charge.

Supply and fix for 75mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm aluminium handles, cast type anodised complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs brass chromium plated shower rose 200x200mm size with 300mm long stainless steel arms complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type wall mount SS-304 premium grade stainless steel soap holder/ stand size 11.5(l) x 8.5(b) x 5.5(h) cm fixed with and including chromium plated brass screws and wooden /plastic cleats complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs CP health faucet including 1m length SS conncting pipe complete all as specified and as directed by Engr-in-charge.

Supply and fix in repair vitreous china wash down water closet (pedestal pattern, ETWC), white including fixing bolts, plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engr-in-charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dresses stonework and precast concrete articles complete all as specified and as directed by Engr-in-charge.

Material and labour for precast cement concrete block type C-1 1:3:6 (Using 20mm graded stone aggregate) masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and as directed by Engr-in-charge.( Item 96 of Job A + item 05 of Job B= 2+5=7)

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required as per manufacturers instructions complete all as specified and as directed by Engr-in-charge.( Item 98 of Job A + item 07 of Job B= 150+30=180) Note: WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja, roof projection, shelves etc., and finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-charge.

Material and labour for plain cement concrete type B-0 , 1:2:4 (Using 12.5mm graded stone aggregate) cast in situ in cills and other similar bands, plinth courses, parapets, copings, hold fast, bed plates, filling hollow section of pressed steel frame and the like including use and waste of form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of new plastered surface of wall by applying 1mm thick wall care putty and making the surface smooth finishing walls and applying acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using roller for painting complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old plastered surface of wall by applying acrylic smooth exterior paint of required shade (one coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using roller for painting complete all as specified and as directed by Engr-in-charge.

Material and labour for preparing new plastered surfaces of walls and applying through mechanical means two coats of oil bound distemper over a coat of alkali resistant primer over and including applying 2mm thickness plaster of paris putty to prepare the surface even and smooth complete all as specified and as directed by Engr-in-charge.

Material and labour for preparing new plastered surfaces of celing surface and applying through mechanical means two coats of oil bound distemper over a coat of alkali resistant primer over and including applying 2mm thickness plaster of paris putty to prepare the surface even and smooth complete all as specified and as directed by Engr-in-charge.

Material and labour for complete removal of existing treatment of old plastered surfaces of walls and applying through mechanical means two coats of oil bound distemper over a coat of alkali resistant primer over and including applying 1mm thickness plaster of paris putty to prepare the surface even and smooth complete all as specified and as directed by Engr-in-charge.

Material and labour for 40mm thick PCC 1:2:4, type B-0 (Using 12.5mm graded stone aggregate) as in flooring complete all as specified and as directed by Engr-in-charge.

Material and labour for 75mm thick PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) for hard standing including finishing the surface even and fair complete all as specified and as directed by Engr-in-charge. ( Item 109 of Job A + item 09 of Job B= 120+50=170)

Material and labour for PCC type C-2 ,1:3:6 (Using 40mm graded stone aggregate) as in surface channels and drain complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 16mm dia brass union complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 20mm dia brass union complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 25mm dia brass union complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 20mm dia male brass threaded adaptor (MTA/MBTA) complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 16mm dia female brass threaded adaptor (MTA/MBTA) complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 20mm dia female brass threaded adaptor (MTA/MBTA) complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 16mm dia ball valve complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 20mm dia ball valve complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 25mm dia ball valve complete all as specified and as directed by Engr-in-charge.

Material and labour for CPVC 32mm dia ball valve complete all as specified and as directed by Engr-in-charge.

Supply and fix for anodised aluminium frame powder coating, for doors, windows, ventilators, partition /fixed type windows, aluminium grill etc., with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including beads complete all as specified and as directed by Engr-in-charge.

Supply and fix 4.8mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including beads complete all as specified and as directed by Engr-in-charge.

Material and labour in repairs for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium sliding window and ventilator shutters, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and as directed by Engr-in-charge. Note: Sheet glass and SS wiremesh shall be measured and paid separately.

Material and labour in repairs for Gl frame size of grid 605x605mm for seamless ceiling comprising of Gl perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and as directed by Engr-in-charge.

Material and labour for seamless calcium silicate ceiling made out of 1800x1200x12mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seam less finish complete all as specified and as directed by Engr-in-charge. Note: Frame work for ceiling shall be measured and paid separately.

Material and labour for preparation of new surface of false ceiling by applying 3mm thick wall care putty and making the surface smooth and applying two coats of oil emulsion distemper over one coat of primer using roller for painting complete all as specified and as directed by Engr-in-charge.

Supply and fix for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed by Engr-in-charge.

Material and labour for 40mm thick teakwood door design framed, heritage and vintage designs panelled shutters (any number of panels) and fitted to chowkats complete all as specified and as directed by Engr-in-charge.

Supply and fix for 150mm long SS handles, fabricated type polished complete all as specified and as directed by Engr-in-charge.

Supply and fix for 300mm long SS handles, fabricated type polished complete all as specified and as directed by Engr-in-charge.

Supply and fix for 200mm long SS tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for aluminium extruded section body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 100mm SS butt hinges, medium weight complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm long SS door stopper, medium weight complete all as specified and as directed by Engr-in-charge.

Supply and fix for 150mm aluminium anodised barrel tower bolts of stove enameled black, with bright bolt and fixed complete all as specified and as directed by Engr-in-charge.

Material and labour for anti termite treatment of soil under existing floors using emulsion @ 1 ltrs per hole 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 sand) to match the existing floors complete all as specified and as directed by Engr-in-charge.

Material and labour for anti termite treatment along the external /internal wall below concrete or masonry apron using chemical emulsion @ 2.25 ltrs per liners metre including drilling and plugging holes etc., in apron complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 18/ 19mm thick BWR plywood, grade 1 with fixed with screws to timber frame work for built in cupboards, shelves, almirahs etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for 1mm thick veneer fixed with adhesive on BWR plywood surface etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for 1mm thick and 20mm wide strips fixed with adhesive on BWR plywood surface etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs for brass mortice lock, vertical type, size 100mm 4 levers include for escutcheon plates and two keys complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs for stainless steel clips on auto closing panel concealed hinges thickness 15-22mm for full overlay door 0 degree crank for cupboard door complete all as specified and as directed by Engr-in-charge.

Supply and fix for 100mm long SS handles, fabricated type polished complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs for magnetic catch complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs sheet glass shelf assembly consisting of 5 to 6mm thick glass 12 to 15cm wide with brass CP bracket guard and railing 45 to 60cm long complete all as specified and as directed by Engr-in-charge.

Supply and fix for horizontal venetian blinds complete all as specified and as directed by Engr-in-charge. TECHNICAL SPECIFICATIONS: 1) Fabric a) Composition - 100% Polyester b) Weight approx - 190 g/m2 (±5%) c) Thickness - 0.41 mm (±0.05) d) Hanging Properties-Excellent e) Tearing Strength-Very High f) Visibility- Translucent g) Operating system - Manual Ball chain 2) Top Tube Blinds top tube extruded by non rusting aluminium alloy with 1.25mm thickness. The channel is designed with support beam to keep it straight and shall have a pocket for holding the fabrics in position. As per windows dimensions, top tube should be in the range of 38 to 45mm diameter. 3) Control Unit Control unit mechanism made by high strength ABS plastic. The mechanism shall be operating with the use of a ball chain. As per requirement there is an option of left or right control.

4) Brackets Universal mounting brackets must be capable of mounting inside /outside/ ceiling /wall with the clutch on either the right or left end of the tube. The brackets are made of mild steel and are powder coated for a greater finish. Brackets shall be accommodating overhead or side mounting with clutch assembly on either end of the blind. 5) Ball Chain Ball chain is made of unbreakable polyethylene plastic, 1.50mm polyester cord with 4.50mm balls. The blind can be stopped at any desired position with the help of a stop lock. Chain jointer is used to secure the chain. 6) Bottom Rail Bottom channel of blind is available in half round shape made of non rusting aluminium powder coated with 1.50mm thickness. The fabric shall be enclosed in the suitably created pocket along with tube. The channel shall be closed from sides with the end caps to give a neat look.

Supply and fix for 12mm toughned glass with suitable SS clamps, SS holder, SS fastener and hinged doors, partitions doors and fixed with wooden frame, aluminum frame similar and SS frame 304 G work including cutting to shape, drilling holes required complete all as specified and as directed by Engr-in-charge.

Supply and fix for SS handle 12" long and 20mm dia glass door handle C type complete all as specified and as directed by Engr-in-charge.

Supply and fix for SS 12mm thick toughned n glass double center door lock complete all as specified and as directed by Engr-in-charge.

Taking down any size geyser before wall tiling and refixing on same place complete all as specified and as directed by Engr-in-charge.

Taking down any exhaust fan in toilet and refixing on same place complete all as specified and as directed by Engr-in-charge.

Taking down any switch boards and refixing on same place complete all as specified and as directed by Engr-in-charge.

Supply and fix for two way reflective road stud cat eye impact resistance ABS plastic body of dimension 100x90mm, reflective panel of amber, red/ white/ yellow/ blue/ green colour with dry and wet reflectivity, fixed at site as per manufacturer's instructions complete all as specified and as directed by Engr-in-charge.

Supply and fix for traffic mirror/ convex mirror of size 32'' for blind spots impact resistant and distortion free, in moulded/ single piece polycarbonate frame alongwith all fittings and fixtures with making front and back holding plates, including 50mm dia GI post including excavation, return filling and PCC 1:3:6 for fixing the post, cost of labour and materials etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for stone bench made up of 35-40 mm stone as approved, of minimum four seating capacity with back rest and both ends arm rest, including carving and making suitable design, pattern, decoration, curvatures and polishing and fixing on ground using PCC 1:2:4 including excavation, refilling and making good of disturbed surface etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for cast iron work grade FG 150, unmachined, in brackets, gratings and benches valve boxes, gate stops, parts of ranges, balusters and similar articles including carving and making suitable design, pattern, decoration, curvatures and polishing and fixing on ground using PCC 1:2:4 including excavation, refilling and making good of disturbed surface etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) type C1, 1:3:6 (Using 20mm graded stone aggregate) and setting in cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Material and labour for hardcore of guage not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-charge.

Material and labour for sand cushioning including watering for interlocking tiles complete all as specified and as directed by Engr-in-charge. Note: Only punned thickness shall be measured for payment.

Material and labour for machine pressed precast conctete glossy finish interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade laying, set, jointed in neat cement slurry and pointed with grey cement mixed with pigment to match complete all as specified and as directed by Engr-in-charge.

EURO ENTERPRISES (BID ID -3419957)

SRI GANESH ENTERPRISES (BID ID -3409392)