GE(S) BTD 46 of 2019-20 REPAIR TO SUNKEN TREATMENT TILLING SANITARY FITTINGS PLUMBING PLASTERING AND CONNECTED WORKS AT OTM II AND III AND REPAIR TO FLOORING PLASTERING PLUMBING WORK AND JOINERY WORK AND OTHER CONNECTED WORK IN EME BN FD WKSP AND E

Amount

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) not exceeding 1.5 Sqm each as doors, windows & ventilators ect. and removal from site complete all as specified and as directed by Engineer-in-Charge.

S&F factory made PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening all as specified in Preamble 8B.2.8 of SSR Part -II (2010) and all as shown on drawing on Sl Page No 160 of SSR Part-II (2010).

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings

Supply and fixing aluminium anodised 100mm long butt hinges with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair aluminium anodised 100mm long butt hinges with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and as directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolt, 150 mm long (ISI marked), fixed to PVC door with screws complete all as specified and as directed by Engineer-in-Charge.

S & F Aluminium anodised handles, 125 mm long, cast type, (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each complete all as specified and as directed by Engineer-in-Charge.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 125 x 60mm, complete all as specified and directed. (thickness of steel sheet shall be 1.25mm) Note:- The quoted rate deemed to include the cost of making good the disturbed surface of wall and floor and matching the colour of new plaster on wall with existing surface. Nothing extra shall be paid on this account.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 105 x 60mm, complete all as specified and directed (thickness of steel sheet shall be 1.25mm)Note:- The quoted rate deemed to include the cost of making good the disturbed surface of wall and floor and matching the colour of new plaster on wall with existing surface. Nothing extra shall be paid on this account.

M & L for PCC (1:3:6) type C-1 using 20 mm graded stone aggregate in copings, filling in bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork complete.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening including easing and adjusting including renewal of unserviceable screws etc. complete all as specified and directed.

Taking down shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm each and removal from site.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 75 x 60mm, complete all as specified (thickness of steel sheet shall be 1.25mm), complete all as specified and directed. Note:- The quoted rate deemed to include the cost of making good the disturbed surface with cement plaster 1:6 and matching the colour of new plaster with existing surface. Nothing extra shall be paid on this account.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified

S&F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

Supply and fixing 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), using 2nd class hard wood (Bonsum / Hollock), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge. Note - Wire gauze / glass to be measured and paid separately

S & F hasp & staple 100mm size, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

M &L for Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed.

S & F MS galvanised mild wire cloth 0.56 mm nominal dia of wire and avarage width of aperture 1.18mm and fixed with tinned tacks to galvanised wire stapple complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aperture 1.4mm and fixed with tinned tacks to stainless steel wire stapple complete all as specified and directed.

S & F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aperture 1.4mm and fixed with tinned tacks to stainless steel wire stapple complete all as specified and directed.

S & F (fixing with screws or welding as per site requirement) 300mm mild steel ordinary rat tail rod springs ( Helical Springs), including roller & roller plate complete all as specifiedand directed.

Supply and fixing mild steel sliding door bolts with hasp and staple, length of bolt 300mm, plate type, stove enameled black, with bright bolts not less than 12 mm dia with and including a minimum of 6 bolts and nuts, 4 on bolt plate and 2 on staple plate and fixed, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing mild steel barrel tower bolts, 200 mm long, stove enamelled black with bright bolts and fixed (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Mild steel pressed handles, 150 mm long, oval type, stove enamelled black (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

Supply only Butt hinges, 100 mm long, medium weight, cold rolled mild steel, (ISI marked) complete all as specified and as directed by Engineer-in-Charge.

Supply only Butt hinges of 75 mm long medium weight, cold rolled mild steel, (ISI marked) suitable for shutter of cupboard etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs ( to be fixed with screws & welding as required) continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flap (when open) 30mm complete all as specified and directed.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed by Engineer-in-Charge.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made steel window or ventilators fixed type/steel frame work as in North light freming work with glazing bars including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

S & F mild steel Casement stays, size 300mm, with hinged joint and two plates, with studs complete all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/springs clips

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane with glazing pins complete all as specified and directed.

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane with glazing pins complete all as specified and directed.

Hacking out old broken glass from metal frame of any thinkness incl punching or drilling out old glazing pins/springs clips and S & F 3mm thick plain, transparent acrylic sheet with oil putty in square nexc 0.5 sqm in each pane including glazing pins complete all as specified and directed. Note:- The height of building is approx 7m for execution of this item ie fixing of transparent acrylic sheet.

S&F framed brackets of angles cut to shape, drilled and counter sunk for screw including bending and welding angles as necessary, each backets conforming to Fe 410-W(Gde-E- 250) quality-A as door frame, sink, hand wash basin and cooler stand etc. complete all as specified and directed by Engineer-in-Charge.

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc. One brick complete all as specified and as directed by Engineer-in-Charge.

M&L for applying two coat of synthetic enamel paint on new steel surfaces of any description exceeding 10 cm width or girth, including preparation of surfaces, complete all as specified and directed by Engineer-in-Charge.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

Demolition of unreinforced cement concrete of any description & in any position not otherwise specifically provided for, complete all as specified and directed.

Demolition of cement concrete (unreinforced) including tiles of any description & terrazo finish, etc. not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

Renewing non skid /glazed ceramic tiles in patches in floor or walls, area not exceeding 5 sqm including cutting out broken tiles carefully, preparing beds and laying or setting, jointing & pointing new tiles complete all as specified (new tiles shall be paid at supply only rate separately)

M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:6 complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as on vertical surfaces in skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick plaster bedding layer in CM 1:4 including taking down old plaster complete all as specified and directed.

M & L glazed ceramic coloured tiles of approved quality in vertical surfaces 450mmx300 mm x7mm/450mm x 350 x 7mm thick set jointed in neat cement slurry/paste and pointed in coloured cement to match with the tiles over and including 15mm thick plaster in CM 1:4 and including dismantling of old tiles/terrazzo finish etc; complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bedding layer in CM 1:6 complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as on vertical surfaces in skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick plaster bedding layer in CM 1:4 including taking down old plaster complete all as specified and directed.

M & L vitrified tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bedding layer in CM 1:6 complete all as specified and directed.

M & L vitrified tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry/paste and pointed in white or coloured cement to match over and including 10mm thick plaster in CM 1:4 complete all as specified and directed.

M&L in repairs marble work (Udaipur green slabs) not less than 16 mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 15mm thick cement screed base in CM 1:4 all as specified including rounding the edges.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completecomplete all as specified and directed by Engineer-in-Charge. Note:- The different size of Kota stone shall be decided by Engineer-in-Charge as per site requirement.

M&L for Kota stone slab 20 to 25 mm thick in riser of steps, skirting, dado and pillar set and jointed in neat cement slurry and pointed in white cement paste pigmented to the match the shade of tiles laid over and including M&L for 10 mm thick rendering in cement mortar (1:4) and finish the surface rough to receive the tile. Note:- The different size of Kota stone shall be decided by Engineer-in-Charge as per site requirement.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450mm of approved quality complete all as specified and directed.

S & F in repairs 15mm bore, fancy type, chromium plated, quarter turn angle cock, cast coppler alloy, screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing in repair brass chromium plated shower rose 125 mm size, with swivel joints, including fixing to steel pipe or union, complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 15mm bore fancy type chromium plated quarter turn stop valve cast copper alloy, with long shank & cup (concealed type) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges all as specified

S & F in repairs soap dish stainless steel as per sample available in AGE B/R-II office, complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x330mm x160mm complete all as specified

M&L for 25mm dia fancy type PVC coated on MS pipe coloured curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories complete all aspecified

Taking down or up 15 mm bore galvanised iron tubing/PL-AL-PE pipes and connection including cleaning for refixing or removal complete all as specified and directed.

Taking down or up 20 mm bore galvanised iron tubing /PE-AL-PE pipes and connection including cleaning for refixing or removal complete all as specified and directed.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and directed.

Refixing old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc complete all as specified and directed. (i) Cleaning of pipe is included in seperate item here in before. (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required at site.

Refixing only old GI tubing 20 mm bore pipe and connections in new or old position as on walls ceiling floors etc complete all as specified and directed. (i) Cleaning of pipe is included in seperate item here in before. (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required at site.

Taking down AC eaves gutters and rainwater pipes (approx 110 mm bore), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 110 mm bore of 6 kg/CM Square pressure fixed to walls with MS clamps of 25 x 3 mm flat iron and fixed with 75 mm long screw with PVC gutties n.exc .1.80 mtr centre to centre distance including making good khura at slab/gutter complete all as specied and directed.

S & F in repairs 160 mm bore of 6 kg/CM Square pressure fixed to walls with MS clamps of 25 x 3 mm flat iron and fixed with 75 mm long screw with PVC gutties n.exc .1.80 mtr centre to centre distance including making good khura at slab/gutter complete all as specied and directed. Note:- The height of building is approx 7m for execution of this item ie fixing of rain water pipe.

S & F 110 mm bore, PVC (SWR) fittings such as bends, tee, shoe etc; fixed to PVC pipes, complete all as specified and directed.

S & F 160 mm bore, PVC (SWR) fittings such as bends, tee, shoe etc; fixed to PVC pipes, complete all as specified and directed.

S&F in repair vitreous china (white) squatting pan 'Orissa' pattern, white, size 580 x 440x260 mm, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti-syphonic pipe etc including making good to floor and including trap set in and including lime concrete complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair PVC Syphon (as per sample) for 10 ltr capacity PVC low level flushing cistern complete all as specified and directed.

Supply and fixed in repair Vitreous china wash hand basin, white, flat back, fancy type, size 550 x 400 mm including cast iron cartilever bracket 32 mm dia brass waste coupling and including fixing of taps, waste fitting and union complete all as specified and as directed by Engineer-in-Charge. Note :- Pillar tap shall be measured as supply only under respective item.

Supply only 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, quarter turn screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair 15mm bore chromium plated brass bib tap long body, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair stop valve for 20 mm bore dia of pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete.

S&F in repair stop valve for 15 mm bore dia of pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete.

Supply and fixed in repair vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap including water closet seat cover of plastic , jet etc. complete including necessary PVC pipe fitting complete all as specified and as directed by Engineer-in-Charge.

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

S & F cast iron sand soil waste and vent pipe 75mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F cast iron sand soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F in repair cast iron, 75mm bore bends (any radius),diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed

S & F in repair cast iron, 100mm bore bends (any radius),diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed

S & F in repair cast iron 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brancheswith oval access door bore complete all as specified and directed by Engineer-in charge

S & F in repair cast iron floor trap with grating 75mm dia including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

S & F in repair cast iron floor trap with grating 100mm dia including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description & in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in bedding, benching of manholes, copings, roof padding/kerbs & surface channel etc. complete all as specified and directed.

M & L for 40 mm thick PCC (1:2:4) type B-1, using 20 mm graded stone aggregate as in floor etc finishing the surface even and smooth with using extra cement complete all as specified and directed. .

S & F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified

Dismantling water tank and removing to store of capacity up to 500 ltr complete all as specified and directed.

Dismantling water tank and removing to store of capacity exceeding 500 ltr but not exceeding 1000 ltr complete all as specified and directed.

Supply and fixing three layers 1000 liter HDPE water storage tanks polyproof. white in colour rotational moulded polyethylene (cylindrical vertical with closed top) hoisted and fixed in position including S&F of suitable size inlet/outlet arrangement & other accessories complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing three layers 500 liter HDPE water storage tanks polyproof. white in colour rotational moulded polyethylene (cylindrical vertical with closed top) hoisted and fixed in position including S&F of suitable size inlet/outlet arrangement & other accessories complete all as specified and as directed by Engineer-in-Charge.

M & L for painting to old wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of surfaces complete all as specified and directed.

M & L for painting to old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coat of synthetic enamel paint including preparation of surfaces.

S & F in repairs CP grating (with or without waste hole), 125 mm size, fixed on floor/nahani traps etc complete all as specified and directed.

Material and labour for reinforced cement concrete 1: 1½: 3 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Supply and fixing mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-charge (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for mild steel TMT bars 8mm dia cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Formwork for rough finished surfaces to soffit of suspended slab such as roof slab, floor slab/chajjas/beams/colns/fins/facia and spiral stair case not exceeding 200mm tick complete all as specified and directed.

M&L brick work with sub class `B' old size bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 but except bricks (old serviceable bricks to be used) complete all as specified and directed. Note : The rate includes for cleaning of old bricks.

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specied and directed by Engineer-in-Charge.

M& L for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces and finishing even & smooth without using extra cement complete all as specified and directed. (Building height upto two story)

M&L for 15mm thick rendering in CM (1:6) on other than fair faces and finishing even & fair, complete all as specified and directed. (Building height upto two story)

M & L for rendering 5 mm thick in cement mortar in (1:3) on ceiling and finishing the surface even & smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of old plastered surfaces on wall and applying one coats of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of old surfaces of walls and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of new plastered surafaces of walls and applying two coats of oil bound distemper over a coat of suitable primer complete all as per manufacturer instructions and all as specified and directred by Engineer-in-Charge.

M&L applying three coats of white wash on newly plastered surfaces on wall including preparation of surface, complete all as specified and directred by Engineer-in-Charge.

M&L applying three coats of white wash on newly plastered surfaces on ceiling including preparation of surface, complete all as specified and directred by Engineer-in-Charge.

M&L for applying two coats of cement base paint over a coat of primer on newly plastered wall and ceiling surfaces including cornices & pillasters etc as per manufacturer's specification & instruction including preparation of surface, complete all as specified

M&L for applying one coat of cement base paint on old plastered wall surfaces including cornices & pillasters etc as per manufacturer's specification & instruction including preparation of surface, complete all as specified

Removal of grass, plants, plant roots etc and cleaning the surface with wire brushing and making the surface good to receive cement plaster complete all as specified and directed by Engineer-in-Charge.

M&L 15mm thick cement plaster in CM 1:4 with water proofing compound and finishing top surface even & smoth as in roof slab /sunken floor , etc all as specified Note :- (1) Only coarse sand will be used. (2) Note:- Water proofing compound shall be measured and paid separately under appropriate item in this BOQ.

M&L for PCC (1:7:12) type F2 using 40 mm graded stone aggregate as in sunken floor fill/mass filling etc. complete all as specified and directed.

Supply only liquid water proofing compund complete all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roof and disposal off retrieved material up to a distance of 100m where directed

Material and labour for 40mm thick brick tiles laid on mud mortar & joints grouted flush pointed in cement mortar (1:3) mixed with 5% of crude oil by weight of cement including filling depressions with mud before laying of brick tiles and matching level with existing brick tile surface complete all as specified and directed by Engineer-in-Charge.

Material and labour for 40mm thick brick tiles laid on mud mortar & joints grouted flush pointed in cement mortar (1:3) mixed with 5% of crude oil by weight of cement including filling depressions with mud before laying of brick tiles and matching level with existing brick tile surface but except tiles complete all as specified and directed by Engineer-in-Charge.

M & L for appling a coat of cold bituminous primer over cleaned plastered surface @ 0.30 Kg/Sqm followed by APP modified five layer ploymeric membrane 3mm thick, minimum wt 3.60 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) manufactured by M/S STP Ltd/IWL India Ltd or as per list of make in tender documents approved by GE, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required & finally finished with bituminous aluminum paint @ 0.10 Kg/Sqm complete all as specified and directed.

Dismantling of asbestos cement sheet (corrugated, semi corrugated, etc.) including AC ridges in large patches as in roof coverings complete all as specified and directed by Engineer-in-Charge. Note:- 1. Opening of existing wind tie where required for taking down of AC sheet is included. Nothing extra shall be paid on this account at later stage.

M&L for prepainted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550Mpa as in wall, fixed with slef tapping screws all as specified complete all as specified and directed.

M&L 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc Fixed with L-type or screws J-type or cranked hook bolts complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Supply and fixing 600x600x4mm thick 'E' board class ie as in false ceiling including supply and fixing 'Tee' grid frame workmade of special section of MS galvanised sheet 0.3mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide 1.6mm thick with flag fixed to RCC ceiling with dash fastner or wraping the suspending wire around the existing wooden/steel purlin/rafter for suspending grid frame work of size 600mmx600mm suspended with 2 Nos, 1.60mm dia GI wire@600mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main tee 37mmx24mmx0.60mm thick, cross runner tee 37mmx24mmx0.6mm and perimeter angle 24mmx24mmx0,5mm thick shall be fixed to wall with GI screw of 40mm long@450mm c/c along the perimeter of wall including or all as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

M&L in repair mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed.

S&F aluminium glazed door with frame of size 100 x44x2mm comprising of shutter rails & stiles (top 75 x 44 x2mm, lock rail 105 x 44 x2mm & bottom rail of 200 x 44 x2mm) of standard extruded aluminium anodisied natural shade/powder coated satin finish sections, closing arrangements, handle for openable shutter and all joindery items required complete with 4.8 mm thick plain/tinted/itched glass, packing with rubber gasket, aluminium beading etc around both sides for fixing of glass as required all as specified and directed by Engineer-in-Charge

Supply and fixing three track minimum 50 micron powder coated aluminium anodised sliding window with three sliding shutter, the size of outer frame three track 100x37x1.5 mm (using two track for glazed window shutter and one track for wire gauged, the section shutter size 37x18x1.2mm) and glazing with 5mm thick transparency glass of polycarbone including all round suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers sliding rollers of nylon with including all necessary fittings complete all as specified and as directed by Engineer-in-Charge.

M & L 75mm thick, cement concrete 1:3:6, type C2 using 40mm graded crushed stone aggregate as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth without using extra cement complete all as specified and directed.

M & L machine pressed precast concrete coloured interlocking paver block any shape, size and pattern, IS - 15658-2006 (Marked) of 60 mm thickness of M-35 grade with grey cement & pigment including 25mm thick sand cushioning complete all as specified and diretced.

Dismantling of ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed by Engineer – in – Charge .

Supply and fixing aluminium glazing fixing type with frame of size 100x44x2mm with one middle member of size 75x44x2mm of standard extruded aluminium anodized natural shade stain finshed section including 4.88mm thick plaint glass packing with rubber gasket aluminium beading etc. around both sides for fixing of glass complete all as specified and as directed by Engineer-in-Charge. Make:- Jindal/ Balco/ indalco

S&F 5mm thick PVC plain colour sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of solvent Cement and fixining at site.

S & F in repair for vitreous china urinal, half stall type, white excluding flushing cistern but including flush pipe, and waste pipeand also including connections to flushing pipe and outpipes, bedding urinal against wall in cement mortar (1:2), securing urinal to plug with and including 60 mm long brass screws, pointing arount urinal back in cement complete.

Material and labour for PCC 1:4:8 type D-2, using 40 mm graded stone aggregate as in foundation fiiling & mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L for complete removal of existing treatment on wall and ceiling (any number of layers) by scraping with steel wire brushes or any other means, including filling depressions only of scrapped surfaces with wall putty and remove vegetable/plants roots from wall/chajjas and preparation of surfaces for further treatment etc complete.

M & L for solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engineer-in-Charge.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

M/s Kamal Builders

B D BATRA AND SONS

M/s Balvinder Singh Engineer and Contractors

M/s Nuway Constructors India Pvt. Ltd.