CA No GE(H)-09/2022-23 SPL REPAIR TO BLDG NO T 1339 OLD URC WITH TOILET BLOCK, T 1323 JQM STORE AND T 1322 FPO OF CERTAIN UNIT IN THE AOR OF AGE BRII AND BLDG NO T 1210 AND T 1215 OF CERTAIN UNIT IN THE AOR OF AGE BR I AT HISAR MIL STN UNDER GE HISAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises all as specified and directed .

Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M&L for hardcore of broken stone or boulders, gauge exc. 63mm and not exc 100mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified.

M&L for PCC 1:2:4 type B0 using 12.50 mm graded crushed stone aggregate as in filling of steel chowkhat, hold fasts, bed blocks & like including necessary formwork complete all as specified and directed..

M&L for PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in hold fasts, bed blocks & like including necessary formwork complete all as specified and directed..

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

All as per serial item No 18.00 here-in-before but except bricks. Note : Old serviceable bricks retrieved from serial item No. 1.00 here-in-before shall be used under this item.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F for factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

S&F stainless steel butt hinges of size 100mm medium weight, cold fixed with stainless steel screws complete all as specified.

S & F 150mm long extruded aluminium alloy handles, fabricated type, anodised (ISI marked) complete all as specified.

S & F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F 100mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S&F in repairs 20mm bore mild steel (powder coated) drapery rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness complete as specified & as directed. Note :- Rates quoted deemed to include S&F of hinges, lugs, lock strike plate.

S&F mild steel framed work in tubular trusses using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

S & F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 35.00 here-in-before but 5 to 10mm dia in stirrups, spacers and binders.

S&F 9mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed in aluminium frame work complete all as specified & as directed.

S&F Door closer aluminium (extruded section body), hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) including shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including powder coated 'D' type handle of suitable size, tower bolt of suitable size, suitable size hinges heavy grade complete all as specified & as directed. Note :- Door closer, Glass panes/wire cloth/Particle board shall be measured & paid seperately under relevant item of BoQ.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F Anodised aluminium snap grid size 605 x 605mm frame work for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F GI powder coated snap grid of size 605 mm x 605 mm frame work for false ceiling with main tee 32x24x1mm thick, cross Tee 26x24x1mm and wall angle 24x24x1mm thick, flange covered with PVC thin includng hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified & directed.

S&F False ceiling with 4mm thick HPSC pre-primer non asbestos fibre cement building board (E-Classic) with decorative finish, factory made, 600mm x 600mm in size and complete all as specified & as directed. Note : The snap grid frame work shall be measured & paid for separately

S&F Gypsum board 7-9mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 595mmx595mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified and directed. Note : The snap grid frame work shall be measured & paid for separately

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in levelling course 50mm thick finished fair & even complete all as specified & as directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured), 1st quality, 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Material and labour glazed ceramic tiles (coloured), 1st quality 350x250x7mm/450x350x7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for factory made 60mm thick machine pressed precast cement concrete coloured interlocking paver blocks glossy finish of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kerb block (factory casted) with plain fair faces, including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M & L for rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls over & including 2mm thick wall care putty all as specified & as directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of white wash on walls all as specified & as directed.

M&L for complete removal of existing treatment on walls (any numbers of layers) by scrapping with steel wire brushing or any other means, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. etc and including filling cracks or holes with white cement putty and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of 1mm thick wall care putty all as specified & as directed.

M&L for complete removal of existing treatment on walls (any numbers of layers) by scrapping with steel wire brushing or any other means, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. etc and including filling cracks or holes with white cement putty and applying two coats of cement base paint of approved shade/tint all as specified & as directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide primer complete all as specified.

Material and labour for preparation of new steel surfaces (already applied with coat of primer) of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint of approved tint on existing primer complete all as specified.

S&F 5.5mm thick dark coloured sheet glass in glazing to aluminium door, window & partition including pad/gasket all as specified and directed.

S&F 3mm thick polycarbonate solid sheet, in square/rectangular size, smooth surface, weather resistant, fine finish, bent and pressed including aluminium glazing clips, rubber beading and clear silicon or glazing with oil putty with putty or fixed with beads complete all as specified and directed.

Dismantling old unserviceable PVC water tank capacity 500 ltr and not exc 1000 ltrs & removal from site etc complete all as specified and directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 15mm bore.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall.

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15mm bore angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repairs 15mm bore stop valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repairs 15mm bore, fancy type brass CP Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook complete all as specified and as directed.

S&F in repairs Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and plastic cleats (Minimum weight 190gms).

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, with 'P' or 'S' trap including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs vitreous china half stall urinal, 580mmx380mmx350mm (minimum), white with grating and union for discharge pipe includng providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plugs with and including 60mm long brass screws complete with PVC flush pipe complete all as specified and as directed.

S&F in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified.

S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified. Note :- Supply only pillar tap shall be measured & paid seperately under relevant item of BoQ.

Supply only 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes & fly nuts, screwed for iron pipes.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. (measured overall as fixed along the centre line over fitting and accessories) complete all as specified.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F in repairs cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.

S&F in repairs salt glazed stone ware gully trap square or round mouthed type 'P' of size 150 x 150 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C-0 block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete, all as specified and as directed.

S&F in repairs 100mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified.

S&F in repairs 75mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified.

S&F in repairs 50mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified.

Supply and fixing CI cowl for 50 mm bore CI pipe complete all as specified

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

S&F 75mm bore cast iron Bends (any radius) with duck's foot or heel rest complete all as specified & as directed.

S&F stack clamps for 75mm dia bore pipe made out of 50mm by 5mm flat iron and 16 mm round iron stay incl bolts and nuts and securing ends stays to wall or roof complete all as specified.

Taking down carefully copper/aluminum point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3 mm thick new bakelite laminated sheet top cover ‘Hylam’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No. 113.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board.

All as per item No. 113.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 113.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi strand on independent board including provn of 2.50 Sqmm unsheathed, multi stranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts all as specified & directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts.

S&F flush type socket outlet multipurpose 3 Pin 5/6 Amp (with 2 pin outlet also) 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp (with 3 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F lamp holder, insluated body, with back plate suitable for batten fittings & complete all as specified & directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F LED bulb of capacity 15 W, ISI marked, all as specified and directed.

S&F Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed.

S&F LED light fitting 1x20W/22W, decorative box type with & including ultra bright glass LED Tubelight with very high efficacy, single / double side connection all as specified and directed. Make : Havells Regal batten Cat Part No REGALBATTENT8UPTO1X22WSSBSWH & LED tube rod Cat Part No PHOTONULTRAE2.01213T8SSTL20WLED865SPC of Havells or Surya Cat Part No SLE BT 20 MS for batten & LED tube rod Cat Part No SLE TL-DS 18 PC Reform of Surya or Cat No LTTB4F20WLEDEW BATTEN for batten & LED tube rod Cat No Cat No LT4F20WLEDT8/WDI of C&S or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F in replacement LED bulk head light fitting 1 x 10 Watt, ultra modern, energy saving, surface mounted, decorative hexagon bulk head lit LED luminaire of high brightness with very high efficiency all as specified and directed. Make : Crompton Cat Part No LBHP-10-CDL or Cat Part No HEXAFT10WLED857SSYMBOPC of Havells or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F in replacement street light LED light fitting 25 Watt (or of nearest higher cap), pressure die cast housing with epoxy powder coating, IP65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 40mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No TRP-400-25-57-SL-LM-NSR of Crompton or equivalent of make as mentioned in Appx 'C' list of makes here-in-after.

S & F sheet metal enclosure, double door type, having door earthing, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 8 way, 240 Volts. Make :- Indo Asian Cat Part No 810321 or equivalent of makes mentioned in list of makes here-in-after .

S & F MCB SP, 6 to 32 Amps 240 Volts , 'B' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 32 Amps 240 Volts , 'B' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

Supply and fixing one star rated energy saving ceiling fan 1200mm sweep as per alest IS-374-2019 having service value > 4 to < 4.5 m3/min/w and 50 watt with double ball bearing and three blades with all accessories, down rod, two nos canopy, white in colour including 2 core 0.5 sqmm copper flexible cable for connection from ceiling rose to fan complete all as specified and directed.

Supply & fixing and testing metal body exhaust fan of 380mm sweep heavy duty, double ball bearing, 900 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete. Make : Model No Turbojet SP of Havells or Cat Part No Supreme DLX HD of Bajaj or Cat No Transair of Crompton equivalent of make as mentioned in Appx 'C' list of makes here-in-after.

Supply , laying , jointing, testing and commissioning of cable of size 10 sqmm 2 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors as per IS 7098 (Part-I), laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe including taking out existing u/s cable complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness afterlaying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed. .

S&F in replacement Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (40mmx6mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note :- Excavation & earthwork shall be measured & paid for separately.

M & L for earthing complete with galvanized iron earth plate electrode of size 60cmx60cmx6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, connected to the galvanized earth lead wire 4mm dia by means of GI bolts/nuts/ washers, protected by 15mm bore GI light grade pipe from earth plate and upto 3m along pole fixed with 2 clamps made from mild steel flat iron 25x3mm bolts, nuts and washers etc. Earth plate shall be surrounded by packed layer of coal dust 300mm and common salt 15cm thick all around bottom and top, 20mm GI medium grade pipe for watering and including funnel , wire mesh , RCC 1:2:4 type B-1 using 20 mm graded stone aggregate cover of size 30 cm X 30 cm X 8 cm thick reinforced with expanded metal weighing not less than 4Kg/Sqm, PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in earthing pit including necessary excavation and earth work, all as specified and shown in electrical plate No-3 of SSR part-I and connected to earthing point and testing on completion complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing.. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.

M/S KAVITA CONSTRUCTION

OM CONSTRUCTION CO.

DALMIA CONTRACTORS