Special repair of Hostel Block of Government Medical College Chhainsa Erstwhile Gold Field Institute of Medical Science and Research Faridabad Civil and PH works only

Amount

Special Repair of Hostel Block of Government Medical College Chhainsa (Erstwhile Gold Field Institute of Medical Science and Research, Faridabad) [Civil + PH Works only]

(Civil Work) Plastering on Wall 12 mm thick Cement Plaster 1:6 (HSR 15.7)(i) 1st Storey

2nd Storey

3rd Storey

4th Storey

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part-I and II, fixed in position, including iron hinges, screws chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):- (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (Duro, Green) 25 mm. thick (HSR 17.93 (a) (i)- note I under 17.18))

Factory- Manufactured panelled door or glazed window, shutters of commercial hard wood, such as hillock, champ. Chikrassy and chaplash etc..(non-coniferous timber other than tak, conforming ot I.S specification no. 1033, kiln-seassoned), with 100 mm wide (HSR 17.90)

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollock, champ, chikrassy & chaplash etc. (Non-coniferous timber other than teak, conforming to IS specification no. 1003, Kiln-seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chocks, cleats, stops, nails etc. complete fixed in position (Excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) -(i)- 30 mm thick (HSR 17.92) (1)-Note I under 17.18.

Supplying and fixing glass panes with moulding of commercial hard wood such as hillock champ, chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming to I.S Specification43.22. 1003, Kiln Seasoned)-(HSR 17.36)C) 4mm

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of with lead, linseed oil, varnish and chalk miti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1) Through Rate

Providing & applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as goodlass- Neolac, Berger, Garware, Jenson, Nicholson, Asian & shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge. (HSR 16.3)Through Rate

Painting two coat excluding priming coat with ready mixed paint for metallic surfaces in all shades are old steel or iron work (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Gareware, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.18) Through Rate

Preparation of plastered or concrete surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing (Note: First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholsan, Asain & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge). [HSR 16.24] Through Rate.

Painting two coats with plastic emulsion paints on walls on new work to give as even shade. (Note: First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholsan, Asain & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge). [HSR 16.30] Through Rate.

Providing & applying two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in oresence of Engineer-in-charge.) (HSR 16.79) (b) Through Rate

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick exceeding 40 sq.m areas. Modi, Saintgobain (HSR 18.30 B)

PH WORK Providing and fixing in position best Indian make European type water closet suite with concealed 'P or 'S trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fitting as fully described in item no. 30.3 above. HSR30.6 (White)-1

Providing and fixing best indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid (HSR 30.13) (i) white plastic seat (solid)

Providing and fixing best Indian make 10 litter capacity PVC of approved make with flush bend and all other necessary fitting as per PWD specification (HSR 30.37 (b) (i)

Providing and fixing in position best Indian make ordinary lavatory suites consisting of:- Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-Charge) including china plug for tap hole where necessary. (HSR 30.41) (iv) White R.S or C.I brackets for building into wall including painting 32mm C.P brass waste with C.P Brass chain and rubber plug 15 mm C.P brass screw down pillar tap with jammuts ot couplings best design (as approved by the Engineer-in-charge) all fittings best Indian make and to the approval of the Engineer-in-Charge All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc. 550mmx400mm with one no. tap

Providing and fixing in position best indian make towel rails fixed in with rawlslugs embedded in walls with C.P Brass screws, complete in all respect including cutting and making goods the walls etc. HSR 30.68 (a) 25mm dia C.P brass adjustable.(ii) 600 mm long

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc. HSR 30.71 (a) Indian make (I) 600mmx450mm

Providing and fixing in position super quality 65 mm i/d opening C.P brass dome type hinged grating weighing about 750 gms fixed in cement mortar 1:2 complete in all respects (as required by the Engineer-in-Charge) (HSR 30.74)

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) HSR 30.75 (a) Bib cock long body

(c) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) HSR 30.76 (a) 15mm stop cock (i) Stop cock male and female end.

Providing and fixing in position best indian make flexible tube connection HSR 30.82 (b) C.P brass i) 15mmx300mm

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. HSR 30.119 (i) 500 Ltr. Cap.

2000 Ltr. Cap

DSR ITEMS Providing and Fixing CP Jet spray as per PWD specification (DSR-17.16A)

Providing and fixing G.I pipes compete with G.I fittings and clamps, i/c cutting and making good the walls etc. Internal work- Exposed on wall [DSR 18.10] (i) 15 mm internal diameter of pipelines (i)

Providing and fixing G.I Union in G.I pipe including cutting and treading the pipe amd making long screws etc. complete (New Work) (DSR 18.46) (a) 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) [DSR 18.17] (b) – i) 20mm I/d

M/s Daksha Construction

Raghubir Singh

M/S DEV PARYAG BUILTECH PVT. LTD.

SRM Buildtech Private Limited