SPECIAL REPAIR TO BUILDING NO P 180 AT AFS JALAHALLI

Amount

M&L for Pre-cast cement concrete block masonry Type C-1 1:3:6 with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

M & L for Cement concrete 40 mm thick type B-1, 1:2:4 (using 12.50 mm graded aggregate) as in leveling coures for fixing of floor tiles, complete all as specified and as directed.

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection finished fair and even, complete all as specified and as directed.

M & L for Cement concrete 50 mm thick type B-1, 1:2:4 (using 12.50 mm graded aggregate) as in level coures for slab to achive proper slope incl cutting holes in bricks or RCC wall for spout/rain water pipe complete all as specified and as directed.

S&F in repair tubular towel rail alumunium annidised 20mm dia 'D' type 60cm long between flanges, all as specified and directed.

Taking down Chowkhats or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkhat or frame(wooden/steel) exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel Square tube, complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick moulded PVC prelam sheet on front face and 2mm prelam coloured PVC sheet on back face, complete all as specified and directed.

S&F of Powder coated aluminium frame work for partition/door frame work with one or more rebates incl Joining cleats,hooks, hangers, beadings,tower bolts,hinges, rubber gaskets etc, powder coating minimum thickness of powder coating 50 micron complete all as specified and as directed.

S&F roller blinds of 100% polyster blackout fabrics of weight of 310 g/m^2 (+-5%) having a fabric thickness of 0.45mm(+- 0.05) and very high tearing strength with roller mechanism and aluminium channel. and complete all as spfd and dirctd. Note - (i) Color and pattern will be as approved by GE. (ii) Contractor will make good the disturbed surfaces as per existing surfaces without any extra cost.

M&L for Anodised aluminium side hung door/window/ventilator shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F butt hinges 75 mm long medium weight, cold rolled mild steel, all as specified and directed

S&F etxtruted aluminium alloy handles, fabricated type anodised 100mm long, all as specified and directed

S&F aluminium anodised, barrel tower bolts of extruded section 100 mm long, all as specified and directed

S&F alluminium alloy sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast of extruded section 250 mm long, all as specified and directed

S&F for steel work in tubular trussess including special shaped washer etc complete using ERW or induction but welded tubes confirming to IS 1161-1979 grade St-240 and necessary ancoring with bolt system to wall / floor where ever necessaty, all as specified and as directed.

M&L for mild steel powder coated pelmet rods 25mm outer dia including 2 Nos of brackets 2 Nos of pintals or side brackets as per site requirement complete all as specified and directed.

M&L Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick colour and any shape having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified incl dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and as directed.

Haking out of glass, any size, shape and thickness from the window / ventilator / doors etc and complete removal from the site carefully all as specifiedand as directed.

S&F 5mm thick frosted glass, ordinary quality and glazing with oil putty in of size not exceeding 0.5 sq. m in each pane, and all as specified and directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats all as specified and as directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed 1:6 including dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M&L coloured Glazed ceramic tiles in vertical surface 600X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm back coat of CM 1:4 including dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M&L Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 15mm thick screed bed 1:6 set including dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing),complete all as specified and as directed. Note - (i) Vitrified tiles are classified under group B1a of the international standard for ceramic tiles ISO: 13006.Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5 % and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (ii) The manufactures test certificate for tiles shall be sibmitted by contractor alongwith sample approval.

M&L Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished light shade, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 10mm thick back coat 1:4 set including dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed. Note - (i) Vitrified tiles are classified under group B1a of the international standard for ceramic tiles ISO: 13006.Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5 % and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (ii) The manufactures test certificate for tiles shall be sibmittedby contractor alongwith sample approval.

M&LGranite (of any type) tiles 18-20mm thick machine cut, on vertical surfaces, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, laid over 10mm thick rendering as back coat in cement mortar 1:4, including demolition of wall tile, complete all as specified and as directed.

M&LGranite (of any type) tiles 18-20mm thick machine cut, in floor, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete including 15mm thick screed bed 1:6 set, including demolition of tiles, complete all as specified and as directed.

M&L for Raking out joints/ pointing with cement or cement lime mortar to random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and as directed

Taking down cement plaster on walls any description incl raking out joints, hacking for key and scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for external wall rendering 20 mm thick (in two layed 15 & 5 mm thick) in cement mortar (1:6) on other than fair face brick or stone surface, finished even & smooth without using extra cement, complete all as specified and as directed.

M&L three coats of white wash on newly plastered ceilings and necessary preparation of surfaces all as specified and as directed.

M&L for Raised pointing with CM 1:4 to random or polygonal rubble, uncoursed or brought upto courses complete all as specified and as directed.

M&L for new plastered surfaces and applying water proof cement base putty@ 300gm (undiluted) per sqm of average thickness 1mm over the putty surfacs the mechanical wall sander having mechanical vaccum mechanism with RPM not less than 1500, sanding pad of 240 girt or above to make the surface free from dust and applying two coats of oil bound emulsion distemper over one coat of interior wall care primer using airless spray technology with max two working pressure of 3300 PSI and capable of operating single spray gun with max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying oil emulsion should be able to spray in hard to reach area and penetration of oil emulsion on the surface etc, all as specified and as directed. Note - Application shall be carried out by skilled labour as per following steps - (i) Mix the putty powder by adding water as per manufacturer instruction and mix with putty mixer with the mixing capacity of min 2.50 kg putty per minute. (ii) Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute with a maximum pressure 3300 PSI. (iii) Allow 6-8 hrs time to dry the putty surface.

M&L for old plastered surfaces and applying water proof cement base putty@ 300gm (undiluted) per sqm of average thickness 1mm over the putty surfacs the mechanical wall sander having mechanical vaccum mechanism with RPM not less than 1500, sanding pad of 240 girt or above to make the surface free from dust and applying two coats of oil bound emulsion distemper over one coat of interior wall care primer using airless spray technology with max two working pressure of 3300 PSI and capable of oprtating single spray gun with max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying oil emulsion should be able to spray in hard to reach area and penetration of oil emulsion on the surface etc, all as specified and as directed. Note - Application shall be carried out by skilled labour as per following steps - (a) Mix the putty powder by adding water as per manufacturer's instruction and mix with putty mixer with the mixing capacity of min 2.50 kg putty per minute. (b) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute bwith a maximum pressure 3300 PSI. (c) Allow 6-8 hrs time to dry the putty surface.

S&F Two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description exceeding 10cm width or girth all as specified and as directed.

M&L Two coats of white wash on ceilings including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L One coat of cement based paint on old cement painted walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces of any description, complete all as specified and as directed.

M&L One coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L One coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F in repairs china wash down water closet (pedestal pattern) EWC white including plastic water closet seat cover and mild steel chromium plated hinging device and connecting to 'P' or 'S' including connecting flush pipe with flushing rim, complete all as specified and as directed.

S&F in repairs vitrous china wash basin white flat back size 550x400mm including brackets, waste coupling full or half threded 32mm dia (min wt 45gms), complete all as specified and as directed.

S&F in repair vitreous china urinal bowl type of flat back, size of 465x355x265mm, white in colour, with greating & unions for discharge pipe complete including provide and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in fixing automatic flushing cistern with brackets, flush pipe, greating and unions for discharge pipe and complete all as specified and as directed.

S&F in repair of CP 1.5m length pipe health faucet all as per Cat part No - ALD-CHR-563 of make - Jaquar or equivalent in other makes, all as specified and as directed.

S&F 75mm PVC (SWR) floor trap, plain with chromium plated grating including jointing with solvent cement, complete all as specified and as directed.

S&F in repair for PVC waste pipe 32 mm dia flexible with cup to fit wash hand basin waste coupling complete all as specified and directed.

S&F in repairs Brass chromium plated 2-in-1 tap 15mm bore of cat part NO (OPP-CHR-15041PM) of jaquar or equivalent for fixing of health faucet and all as specified and directed..

S&F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F PVC (SWR) vent cowl bore of 110 mm bore, complete all as specified and directed.

S&F PVC High or low level flushing cistern 10 liters capacity (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, Joint between flushing pipe and socket of W.C. pan, complete all as specified and as directed.

Supply and fix 15 mm bore fancy type pillars tap, chromium plated cast copper alloy with capstan head, long screwed shanks, complete all as specified and as directed.

S&F stop/angle valves cast copper screwed down high pressure fancy type screwed both ends for pipe or union fixed for 15mm bore, complete all as specified and as directed.

Supply and fix waste coupling of PTMT (half or full threaded) (Minimum weight 32mm), complete all as specified and as directed.

S&F in Grating doom 150 mm dia with waste hole of PTMT. (Minimum weight 100gms), complete all as specified & directed.

Supply and fix 110mm dia PVC bend any radius complete all as specified and as directed.

Supply and fix 50mm dia PVC bend any radius complete all as specified and as directed.

S & F PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and as directed.

S & F PVC (SWR) junction single(single T) equal or unequal with access door bore of pipe 110 mm complete all as specified and as directed.

S & F PVC (SWR) reducers 110 mm complete all as specified and as directed.

M&L for Unplasticiscd PVC pipes 110 mm of pressure rating 10 kgf/cm2 laid in trenches in repair complete all as specified and as directed.

M&L for Unplasticiscd PVC pipes 50mm of pressure rating 10 kgf/cm2 laid in trenches in repair completa all as specified and as directed.

S&F steel tubes medium grade galvanised with all fittings and fixed to walls/ceiling or laid in floor, bore of pipe 15mm dia, including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete including taking up or down steel water tubing and connections 15 mm dia complete all as specified and as directed

S&F steel tubes medium grade galvanised with all fittings and fixed complete to walls/ceiling or laid in floor, bore of pipe 20mm dia, including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4.including taking up or down steel water tubing and connections 20mm dia complete all as specified and as directed

M&L for Rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of water tanks (capacity exceeding 500 Ltr not exceeding 1000 ltr) and considering under Sch of Credit complete all as specified and as directed.

Removing existing uncervicable tar felt on any type any description from roof slab alongwith screed bed, cleaning of surface & removing the debries out side MD land complete all as specified and as directed

Material and labour for rendering 10mm (average) thick in cement mortar (1:4) on concrete surface with integral water proofing compound as per recommendation of manufacturer, complete all as specified and as directed. Note - WPC shall be measured and paid seperately.

M&L for Cutting out cracks to V-section in existing roofs or terracing(width 20mm & depth minimum 30mm), cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M&L for Roof treatment with following applications - (a) Preparation of surfaces by removing all dust, loose particles of RCC slab. (b) Apply polyurethane waterproofing coating on prepared concrete surface of roof slab & up to 500 mm of parapets and crumple joint including junction of roof and parapet. (This stage shall be passed by the GE before next application) (c) Method: Cleaning the surface and applying FOSROC Nitoproof 725 (minimum 0.8 mm dft) over a priming coat of Nitoproof WB primer or equivalent product of Asian paints, M/s MC Bauchemic / CIPY / SIKA / Pidilite Dr Fixit / Thermax / STP applied as per manufacturer’s instructions. NOTES (i) The work shall be carried out as per manufacturer’s recommendation and by authorised applicator of manufacturer. (ii) A performance gurantee certificate for 10 years shall be submitted by the contractor to GE on completion of work and before claming the payment of work.

Taking down carefully copper/aluminum point wiring (light, fan,Power) complete fittings such as switches , ceiling roses pendents , regulators sockets light fittings etc removing to store for keeping in safe costody or for taking credit and making good disturbed surface of wall, floors , roof etc all as specified.

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with suitable Modular plate with outer cover with suitable screws for housing switches socket outlets fan regulators etc. all as specified and as directed.

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with suitable Modular plate with outer cover with suitable screws for one exhaust fan point/ceiling fan /wall fan controlled by one way switch, all as specified and as directed.

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with suitable Modular plate with outer cover with suitable screws for One 2/3 pin switch socket point controlled by 5 Amps switch on Independent board, all as specified and as directed.

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with suitable Modular plate with outer cover with suitable screws for One socket outlet 5 Amps 3 pin on same board, all as specified and as directed.

M & L for Point wiring with 4 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 4 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with suitable Modular plate with outer cover with suitable screws for One 3 pin switch socket outlet combination 15 Amps on independent board, all as specified and as directed.

S&F modular switch single pole one way 6 Amps 1 module, complete all as specified and directed

Supply and fix modular socket outlet, multipurpose 2 in 1 , 3 pin 5 Amps, flush type universal all as specified and as directed.

Supply and fix modular socket outlet, multipurpose 2 in 1 , 3 pin 5 Amps,/16Amps flush type universal all as specified and as directed.

S&F Modular fan regulator 120W, 2 Module for C/F complete all as specified and directed.

Supply and fix ceiling rose, surface bakelite type,PVC, 65 x 50 mm isolated body with three terminals all as specified and as directed.

Supply and fixing in repairs 4 ft LED batten, wattage 20 W, having minimum lumen out put 1880 to 2000 with a system efficiency 100 lume/wattshort circuit and voltage cut of protection and wide operating voltage range - 140V to 270 V 6500 K colour temps, 50000 hrs life, IP 20 with all accessories internally Pre wired and including connecting up with 3 core twisted flexible copper conductor cable 0.75 sq mm from ceiling to fitting, mounted on roof/wall etc. on PVC round bush of suitable approved size at as specified and as directed.

Supply and fixing in repairs 2 ft LED batten, wattage <10 w, having minimum lumen out put >900lm with with specially designed extructed thermal polycarbonate housing with high optically efficient serrated diffuse, isolated multistage CCCV driver with operating voltage range-140V to 270V temp range 0 to 50 deg C, driver efficiency >85%, power factor >0.95, THD<10% colour temp 6500 K, surge protection- 3KV in CM, safty extra low voltage safe leval<60V DC as per IEC strandard,IP 20 protection, life of 50000 hrs with luminaries efficiency > 100lm/W including connecting up with twisted flexible copper conductor cable 1.5 sq mm size from ceiling rose to connector fitting, mounted on roof/wall etc. on PVC round bush of suitable size, all as specified and directed.

Supply and fixing Surface/recessed mounted LED luminaire 600 mm x 600 mm, 36/40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable sizeand including cosidering material & labour for fixing ceiling hight upto 15 Mtr complete all as specified and directed.

Remove and refix existing serviceable ceiling fans 1200/1400 mm sweep/wll fan servicing, painting. of ceiling fan with one coat of synthetic enamel paint by spraying including greasing/oiling, filling cavities with filler after cleaning all dust etc. complete all as specified and as directed by Engineer-in-Charge. Note : cost includes replacement of rubber bush, hanging hook with new cotter pins etc, all as specified and directed.

Remove and refix existing serviceable Exhaust fans 300/225 mm sweep servicing, painting Exhaust fan with one coat of synthetic enamel paint by spraying including greasing/oiling, filling cavities with filler after cleaning all dust etc, complete all as specified and as directed.

S&F LED building security/street light fitting 35/36 watts made up of pressure diecast housing with toughened glass diffuser, with high power LEDs with option of secondary optic with IP66 protection, 110 LM/ watt and wired with accessories including suitable bracket & clamps with bolts & nuts, complete all as specified and as directed.

M&L for sub main wiring with 2 single core stranded copper conductor unsheathed PVC insulated cable 1100V grade, 4 Sqmm drawn through suitable size of non-metallic PVC rigid conduit with 1x4 sqmm copper conductor cable as earth conductor and conduit accessories fixed up in surface/recessed as required, connection up and taking down old wiring complete all as specified and directed. Note - 2 single core stranded copper conductor and one earth conductor including conduit shall be measured one unit.

M&L for sub main wiring with 2 single core stranded copper conductor unsheathed PVC insulated cable 1100V grade, 6 Sqmm drawn through suitable size of non-metallic PVC rigid conduit with 1x 6 sqmm copper conductor cable as earth conductor and conduit accessories fixed up in surface/recessed as required, connection up and taking down old wiring complete all as specified and directed. Note - 2 single core stranded copper conductor and one earth conductor including conduit shall be measured one unit.

M&L for sub main wiring three phase with 4 single core stranded copper conductor unsheathed PVC insulated cable 1100V grade, 4 Sqmm drawn through suitable size of non-metallic PVC rigid conduit with 1x 4 sqmm copper conductor cable as earth conductor and conduit accessories fixed up in surface/recessed as required, connection up and taking down old wiring complete all as specified and directed. Note - 4 single core stranded copper conductor and one earth conductor including conduit shall be measured one unit.

Supply and fix in replacement of Metal clad industrial socket with 5-32A MCB 10KA c curve for control the circuit, all as specified and directed

Supply and fix sheet metal enclosure distribution board SPN, 4 way 240 volts, without bus bar, with IP 42 protection and Double Door, suitable for mounting MCBs, complete all as as specified and as directed.

S&F in repairs MCB DB SPN 8 WAY , horrizontal, double door, 240 V, AC,50 Hz, for MCB DP as incommer and and SP MCBs as out going.IP- 43 protection confirming to IS-13032, universal mounting with copper busbar, neutral link, earth link, earthing shuds detachable gland plates with knockouts on both sides, all as per specified.

S&F in Replacement MCB DB TPN 4 WAY , horrizontal, double door,415V, AC,50 Hz, for MCB DP as incommer and and SP MCBs as out going.IP- 43 protection confirming to IS-13032, universal mounting with copper busbar, neutral link, earth link, earthing shuds, all as specified and directed

S&F in Replacement MCB TPN 415 volts 63 Amps, 10 KA rupturing capacity 'B' series, all as specified and as directed.

S&F in Replacement MCB TP 415 volts 40 Amps, 10 KA rupturing capacity 'B' series, all as specified and as directed.

S&F in repairs MCB single pole and neutral 240 volts 40 Amps, 10 KA rupturing capacity 'C' series, all as specified and as directed.

S&F in repairs MCB single pole 240 volts 5 to 30 Amps, 10 KA rupturing capacity 'C' series' all as specified and as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thick above or below ground level, all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed.

A.GOVINDARAJ (BID ID -3141501)

SREE BUILDERS (BID ID -3144674)

chowdeshwariconstructionco (BID ID -3143756)

Sai Ram Builders (BID ID -3146054)

D NAGI REDDY (BID ID -3145653)

G K CONSTRUCTIONS (BID ID -3145906)

K. VENKATESH NAIDU (BID ID -3145655)

Maruthi constructions (BID ID -3146133)