ADDITION ALTERATION AND SPECIAL REPAIR TO STRUCTURE HOUSING COMPRESSOR ROOM AT C NO 50 OF WEAPONS DIV SPECIAL REPAIRS TO TOILETS AND SUNKEN FOORING INCLUDING WATER PROOFING AT DAG DEPT BLDG NO P196 AND TO BLDG NO P1 B3 NAVY HOUSE AT NAVAL DOCKYARD

Amount

Taking down chowkats or frame with shutter ( without taking off shutter from frame) , n exc 1.5 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frame with shutter ( without taking off shutter from frame) exc 1.5 sqm but n exc 4 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down and refixing of shutter in same opening after rescuring or easing and adjusting in the same opening n exc 1 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down and refixing of shutter in same opening after rescuring or easing and adjusting in the same opening exc 1 Sqm and n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down 15mm bore GI tubing including all connectionscomplete all as specified and directed by Engr-in-Charge.

Taking down 20mm bore GI tubing including all connectionscomplete all as specified and directed by Engr-in-Charge.

Taking down 25mm bore GI tubing including all connectionscomplete all as specified and directed by Engr-in-Charge.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches including all connecting fitting complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primesed completed all as specifed and directed Note: The place of disposal shall be find out by the contractor.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris out side MD land. Note: The place of disposal shall be find out by the contractor.

Demolition of RCC of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition and separating, scraping and cleaning of reinforcement and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including removal of rubbish out side MD land. Note: The place of disposal shall be find out by the contractor.

Material and labour for second class hardwood (SAL) plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

Supply & Fix 40mm thick flush shutter solid core construction, with black board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge.

Supply & Fix 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed by Engr-in-Charge.

Supply and fix 150mm size brass handle cast type polished bright complete all as specified and directed by Engr-in-Charge.

Supply & Fix in repair 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed complete all as specified and directed by Engr-in-Charge.

Supply & Fix in repairs 200mm long brass barrel tower bolts of extruded sections complete all as specified and directed by Engr-in-Charge.

Supply & Fix in repair 140mm long floor door stopper of brass body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified .

Supply and fix Decorative laminate 1.50 mm thick, type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed by Engr-in-Charge .

Supply and fixing for Providing and fixing factory made uPVC white colour Sliding window Three track area exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed by Engr-in-Charge. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

Material & Labour for 100mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Dismantling timber scantlings 40 Sqcm and over in section, in any position as in framed works complete all as specified and directed by Engr-in-Charge.

Dismantling timber scantling, unframed in post, rafters, purlines etc under 40 sqcm in section where necessary complete all as specified and directed by Engr-in-Charge.

Material & Labour for brick work with sub class 'B' bricks (old Size) straight or curved on plan exc 6 m mean radius and built in CM (1:6) complete all as specified.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall in cm (1:4) complete all as specified.

Complete removal of existing water proofing treatment of any description in any position including cleaning, wire brushing, washing out with water and finally remove dirt using air jet and removal of debries out side MD land complete as directed by Engineer-in-charge .

Material & Labour for brushing neat cement slurry with 3.0 kg of cement per Sqm on cleaned and washed concrete surfaces and like complete all as directed by Engineer-in-charge.

Material & Labour for PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining roof/chajja/floor slope and finished top surface even and fair complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating as directed including formwork complete all as specified .

Material & Labour for providing five layered water proofing treatment with 4mm thick APP (Atactic Polypropylene) modified bituminous membrane re-inforced with non woven polyester mat of weight not less than 180 gms/Sqm as centre core and without multiple layers of polythene finished on top and bottom with 7 micron thick flammable polythylene applied by thermo fusion using LPG torch on bottom portion of the membrane after applying a coat of bituminous primer @ 0.25 Kg/Sqm over roof and over the APP membrane provide a polypropylene/ polyester, non woven geotextile fabric of 150 gsm over the geo textile fabric (An overlap of 100mm at end & 75mm shall be provided on sides ) complete all as per manufacturers instructions and as directed by Engineer-in- Charge.

Material & Labour for rendering 20mm thick in CM (1:3) mixed with WPC by weight of 3% of total weight of cement on roof top surface and finished even and smooth complete all as specified and directed by Engr-in-Charge. Note : WPC will be measuerd and paid separately.

Supply only integral water proofing compound complete all as specified and directed by Engr-in-Charge.

Material and labour for cement concrete tiles 250 mm x 250 mm x 22 mm thick, with grey cement and no pigment, machine pressed; set, jointed and pointed in neat cement slurry laid over and including 15 mm thick screed bed or bedding layer in cm (1:3), and cut and polished complete all as specified.

Material and labour for expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.90mm dia or fixing with galvanised steel staples, weight n exc 4 Kg per Sqm and fixed to wood or steel members complete all as specified.

Supply and fixing stainless steel wire cloth 0.36 nominal dia of wire and average width of aperature 1.4 mm and fixed with stainless steel wire staples complete all as specified

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Supply & Fix 160 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, ceilings with and including suitable size GI clamps or laid in floor etc with and including fixing clips complete all as specified and as directed by Engr-in-Charge.

Supply & Fix 160mm bore PVC (SWR) bends any radius with rubber ring joints complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repairs 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/ ceiling with and including suitable size GI clamps complete all as specified and directed by Engr-in-Charge and directed.

Supply & Fix 110 mm bore PVC (SWR) bends any radius complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs vitreous china wash down water closet pan (Padestal pattern) white, including matching plastic sheet cover, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodized hinging device complete all as specified.

Supply & Fix in repair Soap Dispenser with Glass Bottle with chrome finish (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge and directed.

Supply & Fixing in repairs health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook chrome finish (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 500hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge .

Supply & Fixing Under Counter vitreous china wash Basin with Fixing Accessories, Size: 705x460x195 mm including 32 mm dia brass CP waste coupling , 32mm dia PVC waste pipe 90cm long and making all connections complete all as specified and as directed by Engr-in-Charge

Supply & Fixing Single Piece vitreous china WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size: 370x695x795 mm, S trap-300mm including connecting piece and making all connections complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repairs toilet roll holder with flap chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) wall mounted complete all as specified and directed by Engr-in-Charge

Supply and fix health faucet with flexible pipe(ABS Body) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook fixed to 15mm bore stop cock and wall hook complete all as specified and directed.

Supply & Fixing in repairs chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) towel ring square with round flange of size 210mm x 210mm complete all as specified and as directed by Engr-in-Charge

Supply & Fixing 32 mm dia flexible waste pipe suitable for WHB/urinal complete all as specified .

Supply & Fix in repair soap container (soap dish) 110mm dia chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) fixed with chromium plated brass screw complete all as specified .

Supply & Fixing in repairs Corner glass shelf with brackets and railing of size 255mm chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and as directed by Engr-in-Charge

Supply & Fixing 600 mm size glass self assembly fency type with frame chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) fixed with chromium plated brass brackets and screw complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing in repairs 15 mm bore Pillar cock with lift type operating knob and base flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified .

Supply & Fixing in repairs 15 mm bore bib cock Bib Cock (Straight Line Model) With Wall Flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 5 mm bore angular stop cock with wall flange chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass ) complete all as specified and directed by Engr-in-Charge.

Supply & Fixing overhead shower of 150x150 mm square shape (ABS Body chromium plated with gray face plate) with rubit cleaning system chrome finished (with plating of Nickel-10 micron, chromium-0.3 micron and salt spray 200hrs + validated adhesion pass )

Material & Labour for rendering minimum 20mm thick using polymer modified mortar in cement mortar (1:3) with graded quartz sand with additive Monolith - PMM @ 15% by weight of cement in one coat with and including curing as per manufacturer's instructions complete all as specified and directed by Engr-in-Charge

Supply and fixing powder coated aluminium sections (minimum thickness of powder coating 25 micron) for partitions, windows, ventilators and doors including fabrication of frame/shutters and fixing to walls/floors with necessary lugs, jointing cleats etc including all accessories such as necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading, rollers, SS screws etc including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required complete all as specified Note: - (i) Glass panes will be measured & paid separately. (ii) Rubber beading will not be weighed and paid separately

Material & Labour for 4 mm thk Sheet glass ordinary quality and glazing in aluminium beading with screws/ rebates in square exc 0.5 sq.m in each pane complete all as specified.

Supply & Fixing 10 to12mm thick, toughened glass for door shutters, partitions, shelves etc with and including fitting and fixtures such as stainless steel handles, studs, cubical hinges glass to glass and glass to wall, 19/20 mm pipes including fittings to hold the glass, top and bottom SS pivots, making necessary holes etc complete all as specified and directed by Engr-in-Charge .

Supply & Fixing for brass Mortice lock, vertical type, size 100mm, 4 lever lock complete all as specified and directed by Engr-in-Charge.

Supply & Fix Door closer hydraulically regulated, designation No. 3,universal type, extruded aluminium body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr-in-Charge.

Material & Labour for aluminium anodized grill DG -102 7.5mm size made out of 75mm thick aluminium plate of weight not less than 3.26 Kg/ Sqm and tensile strength 19 Kg/Sqmm with suitable aluminium anodized frame of F/H section with suitable fixing screws/attachment etc complete all as per manufacturer's specifications.

Supply & Fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification and drawings shown in SSR Part II.complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M.S.frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete as per specification and drawings shown in SSR Part II.complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing 300mm long Aluminium anodised sliding door bolt , with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified and as directed by Engr-in-Charge.

Material & Labour for Non skid coloured ceramic tiles 7 to 8 mm thick (square/Rectanglar) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floor laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour for coloured glazed ceramic tiles 450mm x 350mm x 7mm thick but laid on vertical surfaces such as skirting/dado laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified.

Supply & Fixing in repairs false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Grid of modular size 600mmX600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit with and including 6mm thick high pressure steam cured non asbestos fiber cement designer ceiling board complete all as specified.

Material & Labour for POP false ceiling using 600 x 900 x 12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work main joist of size 50 x 25 mm spaced at 750 mm centre, secondary joist of size 75x20 mm fixed to main joists spaced t 900 mm suspended to roof members using 25 x 25 x 2 mm GI angles and fasteners @ 1.2 m C/C including decorative design/pattern all as specified and directed Engr-in-Charge.

Material and labour for RCC 1:2:4 type B1 (using 20 mm ground stone aggregate) in slabs supported on walls, beams and columns in floors, roofs ,landings ,balconies canopies ,deck slabs and in shelves and the like including necessary formwork complete all as directed.

Material and labour for TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with the clips complete all as specified .

Ditto- all as per item No 77.00 above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders.

Supply & Fixing for rolled mild steel Sections as in post, runners, rafters, purlins, trusses, steps etc fixed with connecting plates including bending, welding etc conforming to Grade Fe 410-W, (Gde- E-250) quqlity-A, complete all as specified.

Supply and fixing mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, without any attachment including all necessory drilling, bolting,riveting or welding conforming to Fe 410 -W (Gde E- 250) quality-A complete all as specified.

Material and labour for rolled mild steel in framed work as in door or gate of angle or other section with gusset plates, rails, braces etc complete,drilled for fixing of steel sheeting or other covering. Doors/gates to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings( exclusive of steel sheating or other covering,running rails and guides) and hanging also fastening and fixing conforming to Fe 410-W ( Gde E-250 ) quality A complete all as specified.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Supply & Fixing pre-painted galvalume aluminium zinc coating GI baseds corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified

Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & and direected.

Material & Labour for 1.5mm thick galvanised steel sheet as in valley gutters fixed with rivets or other suitable arranement over MS brackets trapezoidal shspe of required profile with desired slope etc at any height including dismentling of old valley gutters complete all as specified and directed by Engr-in-Charge .

Supply and fixing 15 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Supply and fixing 20 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Supply and fixing 25 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Disconnecting existing 1000 ltr capacity PVC water tank any type and pattern and in any position, setting aside (or lowering if required) complete all as specified and directed.

Supply and fixing rotational moulded polyethylene water storage tank 1000 Ltr capacity, (cylindrical vertical with closed top) including all connections for inlet, outlet, overflow and washout etc hoisted and fixed in position and providing 20 mm bore ball valve, high pressure with polythene float & fly nut, screwed for iron pipe or brass ferrulall as specified in SSR Part-I including PVC cover with locking arrangement complete all as specified.

Material & Labour for 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears with cement joints fixed to walls with suitable size GI clamps or laid in trenches etc complete all as specified and directed by Engr-in-Charge .

Material & Labour for 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears with cement joints fixed to walls with suitable size GI clamps or laid in trenches etc complete all as specified and directed by Engr-in-Charge .

Supply & Fixing 75mm bore CI bends, diminishing pieces or tapers (larger bore measured) fitted with oval access doors and jointing with cement mortar complete all as specified.

Supply & Fixing 100mm bore CI bends, diminishing pieces or tapers (larger bore measured) fitted with oval access doors and jointing with cement mortar complete all as specified.

Supply & Fixing in repair cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1, diameter of outlet 75mm bore complete all as specified and directed by Engr-in-Charge .

Supply & Fixing in repair cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1, diameter of outlet 100mm bore complete all as specified and directed by Engr-in-Charge .

Supply and fixing in repairs vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap and provision of lime concrete bedding complete all as specified.

Supply and fixing in repairs vitreous china wash down water closet pan (Padestal pattern) white, including 'P' or S trap and matching plastic sheet cover, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodized hinging device complete all as specified.

Supply & Fixing vitreous china urinals,half stall type, flat back, white, with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1: 2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe and making all connections complete all as specified.

Supply and fixing vitreous china wash hand basin white of size 550mm x 400mm flat back including cutting for and pinning in ends of brackets including brackets, 32 mm dia brass CP waste coupling and 32 mm bore PVC waste pipe and fitted to wash basin complete all as specified.

Supply and fixing low level PVC flushing cistern of heavy duty, 10 Ltrs capacity, syphonic action type complete with inlet, ball valve, float and handle including cast iron bracket and 32 mm bore PVC flush pipe and connecting to WC complete all as specified.

Supply and fix flush pipe of PVC 32 mm dia for low level cistern.

Supply and fixing 15 mm bore bib tap, cast copper alloy chromium plated fancy type shank and crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

Supply & Fixing in repairs 15mm size Stop Valves fancy type chromium plated with crutch or butter fly handle screwed down, screwed for iron pipe complete all as specified

Supply and fixing in repairs15 mm bore pillar taps cast copper alloy,chromium plated fancy type with capstan heads screwed down high pressure with or without lettered `Hot' or `Cold' with long screwed shanks and fly nuts screwed for iron pipe or brass ferrule complete all as specified.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm.

Supply and fixing PVC (SWR) floor trap, plain with grating including jointing with solvent cement, diameter of outlet 75 mm.

Supply & Fixing PVC bathroom cabinet with 4mm thick looking mirror of overall size 560x410mm of approved tint and pattern and fixed to wall with chromium plated screws complete all as specified and directed by Engr-in-Charge

Supply and fixing 125 mm dia shower rose, brass chromium plated with swivel joints and fixing to 15 mm bore steel water tubing .

Supply and fixing in repairs 20 mm dia brass chromium plated 'D' type towel rail 60 cm long fancy type including necessary brackets and fixed to wall with CP brass screws complete all as specified.

Supply and fixing in repairs vitreous china white soap dish approximate size 160 x 160 x 90 mm fixed to plug with chromium plated brass screws complete all as specified.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished fair and even completed all as specified.

Material and labour for preparing new plastered surfaces of wall, applying one coat of wall care putty not less than 3mm thickness and making the surface even and smooth using emery paper and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified.

Material and labour for complete removal of existing treatment including washing, rubbing down and stopping of distempered and painted wall surfaces, filling holes and cracks with filling putty on wall and applying one coat of wall care putty not less than 3mm thickness and making the surface even and smooth using emery paper and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified..

Material and labour for rendering 20mm thick in two coats(15mm inner coat + 5mm finishing coat) on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with integral water proofing compound @ 3% by weight of cement and finished fair and even including necessary scaffolding and safety arrangement complete all as specified and directed by Engr-in-Charge. Note- Water proofing compoundshall be measured and paid for separately.

Material and labour for rendering 15 mm thick on fair faces of brickwork or concrete surfaces of wall in CM (1:4) mixed with integral water proofing compound and finished fair and even including necessary scaffolding and safety arrangement complete all as specified and directed by Engr-in-Charge. Note- Water proofing compoundshall be measured and paid for separately.

Material & labour for chipping, removing carefully concrete work by low impact hammer breakar without damaging the structure ( hard concrete should not be removed by force) including necessary scaffolding and safety measures complete all as per manufacturers instructions and as directed by Engr-in-charge. Note: The place of disposal shall be find out by the contractor.

Material & labour for providing and applying structural grade EPIBOND-21-LP prior to application rendering/ plaster confirming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete complete all as per manufacturers instructions and as directed by Engr-in-charge.

Material & labour for Building up the profile of structural members by using latex additives (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond -5 Cement -15 sand) - in damaged areas in 30mm thickness including leveling profliling including necessary scaffolding and safety measures complete all as per manufacturers instructions and as directed by Engr-in-charge.

Material & Labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces including necessary scaffolding and safety measures complete all as per manufacturers instructions and as directed by Engr-in-charge.

Material & Labour for preparation of new plastered or un plastered wall surfaces, over 10cm width or girth and applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer including necessary scaffolding and safety measures complete all as per manufacturer's instructions and directed by Engr-in-Charge.

Material & Labour preparing surfaces by complete removal of existing treatment of wall surfaces, over 10cm width or girth and applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer including necessary scaffolding and safety measures complete all as per manufacturer's instructions and directed by Engr-in-Charge.

Material & Labour for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Material & Labour for preparation of old steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material & Labour for preparation of new wooden surfaces of any description over 10 cm width or girth, applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material & Labour for providing 12 mm dia holes of 75mm deep @0.6 m c/c at junction of beams and columns as co-ordinal points for inserting/pouring mixture of resin base latex polymer and cement slurry by pressure grouting for column, beams and slabs, includind sealing the holes with CM 1:3 complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for PCC 1:7:12 type F2 using 40 mm graded stone aggregate as in filling sunken portion complete all as specified.

Material and labour for preparing sunken portion of RCC floors and walls by wire brush to remove dirt, dust etc cleaning with water and applying water proofing treatment as per manufacturers instructions and comprises of the following activities:- i) Sealing the surrounding of GI pipe and junctions with epoxy mortar. ii) Applying rendering 6 mm thick in cement mortar (1:4) mixed with integral WPC on floor and wall surfaces upto 100 mm above FFL of sunken portion and finished even and smooth without using extra cement. iii) Fill the water and check for dampness and seepage. iv) Apply two coats of polymer modified cementious water proofing coating of minimum thickness of 1 mm for each layer as per manufacturers instructions on floor & walls (upto 100 mm above FFL) and spray coarse sand on surface when the second layer is still sticky. Note : a )If leakage/Seepage occured after filling water, the above said treatment shall be re-done completely without any extra cost. b) WPC will be measured and paid seperately.

Material and labour for 20mm thick granite stone slab (of any type) machine cut, laid in floor, skirting etc over and including 15mm thick backing coat in cement mortar 1:4, bedded and jointed with grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified.

Material & Labour for rounding, moulding to edges of 18-20mm thick grenite stone including machine polishing to edge to give high glossy finish complete all as specified.

Material and labour for machine pressed precast concrete inter locking paver block any shape and size with grey cement and pigment conforming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints and gently rolled with vibrator complete all as specified .

Material & Labour 10mm thick double premium quality charged vitrified ceramic tiles, of approved colour (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors laid over and including 20mm thick screed bed or bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour 10mm thick double premium quality charged vitrified ceramic tiles, of approved colour (square/rectangular) polished, area of each tiles exc. 0.36 Sqm but n.exc. 0.42 Sqm, in floors laid over and including 20mm thick screed bed or bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material & Labour 10mm thick double charged vitrified ceramic tiles, premium quality of approved colour (square/rectangular) polished, area of each tiles exc. 0.36 Sqm but n.exc. 0.42 Sqm,, as in vertical surfaces such as skirting/dado etc., laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth & applying one coat of synthetic enamel paint complete all as specified.

Material and labour for rendering 5 mm thick on fair faces of concrete surfaces in ceiling in CM (1:3) and finished even and smooth without using extra cement including scaffolding and safety arrangement complete all as specified.

Material & Labour preparation of new plastered surface of ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer including scaffolding and safety arrangement complete all as specified.

Material and labour for errection of MS tubler double scaffolding (H frame) upto height of 30m & with necessary brazing, provision of necessary safety equipment to the skilled workers to carry out the work and covering with green cloths for carring out external face work of walls & dismantling after completion all as specified and directed by Engineer in Charge

Material & labour for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing 40mm thick polymer plaster (1:5:15, cement, sand, polymer) and finally finishing the surface complete all as specified and directed by Engr-in-Charge. Make :- Reinforcement and MS Sections will be measured and paid separately.

Material and labour for form work to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete flat.

Material & Labour for 5 mm thick Sheet glass ordinary quality and glazing in aluminium beading with screws/ rebates in square exc 0.5 sq.m in each pane

Supply & Fixing 150mm extruded aluminium alloy handles, cast type as fixed complete all as specified and directed by Engr-in-Charge .

RELIEVING STRUCTURAL MEMBERS:- Material & Labour for Relieving structrural members such as column, beam and slab of their superimposed loads partially or fully by provison of adjustable steel props, frames etc. including providing necessary timber runners, bracing, jacking up arrangement complete all as specified and directed by Engr-in-Charge and directed. Note-Removing and redoing of brickwork, if required, shsll be measured and paid separately.

Material & Labour for Providing and executing Polyurethane Injection system (nozzle) to leakage points and after cleaning the surface and remove any dust, unsound or contaminated materialetc. fixing of packers for injection and seal all the cracks using Nitomortar PE-Polyester resin based repair mortar, injection Nitofill WS60 Rapid foaming and setting resin for stopping flow of water which produces a rapid setting water stopping foam in running water, when the water is stopped the cracks are reinjected with Nitofill UR63-Solvent free two part Polyuretha ne resin. Once grouting operation is completed remove the packers and make good any holes or voids with Nitomortar PE and allow to cure etc. complete as per manufacturer's specifications and directed.

NITOFILL WS60 crack injection resin for stopping water flow

NITOFILL UR63 , solvent free, two part polyurethane resin for sealing cracks.

NITOMORTAR PE , high strength jointing and multi purpose repair compounds

Supply and applying microconcrete aroung edges of Dock walls, jetties, corners, grooves, alters, steps, piers and other marine structure after complete cleaning of concrete surface and applying epoxy coat as bonding agent for bonding between old and new surface, including all lifts, shuttering of column, roof, wall, beam etc as per site condition and all as specified and directed by Engineer in Charge

Supply & Fixing in repairs rolling shutter with/without ball bearing, thickness of laths 1.25mm as specified including top cover, anchoring rod, hasp and staple, gear operated type with chain wheel and hand chain and erected in position including appling two coats of synthetic enamel paint over a coat of primer complete all as specified.

Supply & Fixing boarding 25mm thick 2nd class Hardwood (Sal) boarding, clean sawn in roof,ceiling over the rafter, purlines and fixed with nails complete all as specified.

Dismantling false ceiling/boarding any description fixed in any position with nails.

Supply & Fixing 4mm thick backelite sheet with decoratve choice lamination on both sides complete as specified and as directed

Supply and fix in repairs 25 mm thick machine cut and machine polished cuddapah stone slab, bedded and jointed in neat cement paste as in cooking platform,shelves etc complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for .

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces of wall in CM (1:6) mixed with WPC@3% by weight of cement and finished even and smooth with and including 1 mm thick neeru complete all as specified. Note- WPC shall be measured and paid separetely.

Material & Labour for preparing plastered surfcee of roof slab, chajjas etc, by brooming with broom sweeping free from dirt, dust etc and evenly applying a coat bituminous primer @ 0.20 Kg/Sqm complete all as specified and directed by Engr-in-Charge.

Material and labour for preparing plastered or unplastered wall surfaces to receive the finish as per manufacturers instructions and applying high quality decorative texture finish paint based on 100% acrylic emulsion having long lasting finish with low dirt pick up and has slight sheen with excellent adhesion on washability ( comprising of one coat of wall sealer or acrylic primer and two coats of texture finish) complete all as specified.

Supplying, fitting and fixing 12mm thick Laminated wooden Flooring Work conforming to EN13329:2006 with plank size not Iess than 1200 mm X 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density > 850 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture (< 8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer 'T' profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge. Cost of Laminate Floor Accessories only (Skirting ,End edge, T- moulding,Reducer) shall have to be added separately,wherever required complete all specified and directed by Engr-in-Charge.

Supplying, fitting and fixing 12mm thick Laminated wooden skirting Work conforming to EN13329:2006 with plank size not Iess than 1200 mm X 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density > 850 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture (< 8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer 'T' profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge. Cost of Laminate Floor Accessories only (Skirting ,End edge, T- moulding,Reducer) shall have to be added separately,wherever required complete all specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 4 mm thick bakelite sheet with decorative choice lamination on both sides complete all as specified and as directed

Supply & Fixing 3 mm thick Aluminium composite panel cladding plain metallic of approved colour/ shade to beam/ column/ slab in circular/ rectangular shape including cutting, notching, bending to shape as required jointing with silicon gel of approved colour & Aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm c/c on exceeding col/beam/ slab to hold APC cladding etc. (Note:- Colour/ Pattern of ACP sheet shall be given by GE)

Supply & Fixing in repair plastic net of square/ hexagonal size/pattern made out of 1mm dia of plastic wire complete all as specified and directed by Engr-in-Charge.

Supply & Fix in repair roller/venetian blinds vertical/horizontal type made out of standard transparent 2-3mm polythene of approved texture with necessary accessories complete all as specified and directed by Engr-in-Charge

Supply & Fixing in repair 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work/metal Frame Work complete all as specified and directed by Engr-in-Charge

Material and labour for providing and injecting chemical emulsion for post constructional anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution ) @ 0.5 ltr/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed by Engr-in-Charge

Material & Labour for epoxy base joint paint on external surfaces of walls to fill the gap with and including resin and hardner in proportion as per manufacturers instructions complete all as specified and directed by Engr-in-Charge

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, ceiling roses, lamp holders, brackets & other fitting & Fixtures connected, and making good to disturbed surfaces as directed by Engineer-in-Charge.

Material and labour for concealed point wiring with 1.5 sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including 25mm heavy grade PVC conduit (ISI marked) with all accessories and terminated in and including PVC modular box with modular cover plate and frame of sutable size including 1.5 sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for the following :- Note: Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

One light point controlled by one 5A switch

One Fan/Exhaust fan point controlled by one 5A switch

One 5A flush type switch socket point on same board with other switches

One 5A flush type switch socket point on independent board

Material and labour for concealed point wiring with 2,5 Sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including 25mm heavy grade PVC conduit (ISI marked) with all accessories and terminated in and including surface PVC modular box with modular cover plate and frame of sutable size including 2,5 Sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for One 5pin, 15 Amps switch socket combination on indipendent board. Note: Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & Labour for point wiring (Work station for computer) with 4 Sqmm (nominal area) PVC insulated and unsheathed multistranded FRLS copper conductor cable 1100 volts grade drawn through and including suitable size surface PVC casing caping (ISI marked) with all accessories and terminated in and including surface PVC modular box with modular cover plate and frame of sutable size including 4 Sqmm size PVC insulated, unsheathed, multistranded FRLS copper conductor cable for continuous earth conductor and connecting to earth dolly for complete necessary electric connection for each work station point comprising of 03 Nos 5A sockets with 1.5 sqmm and 01 No 15A socket with 4.0 sqmm on same board complete all as specified and directed by Engr-in-Charge. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Supply and fix switch piano flush type single pole one way 5 Amps, complete all as specified .

S & F Modular switch 1 way 6 Amps, 1 module complete all as specified.

S & F Modular switch 1 way 16 Amps, 1 module complete all as specified.

S & F Modular Socket, 6 Amps 2/3 pin combined 2 module complete all as specified.

Supply & Fixing modular socket 6/16A, 2/3 pin, combined 2 module complete all as specified.

Supply and fix ceiling rose surface bakelite three terminal of size 60x50 mm,240 Volts AC complete all as specified.

S & F Modular stepped type fan regulator, 120 Watt, 2 module complete all as specified.

S & F in repairs Modular stepped type fan regulator, 120 Watt, 2 module complete all as specified.

Disconnecting and taking down the fan and Overhauling of ceiling fan any size and make, dismantling parts, properly cleaning/removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust, rust and applying two coat white enamel paint over a coat of steel primer by spray painting , assembling and refixing at same position complete all as specified and directed by Engr-in-Charge.

Supply & Fix in repairs MCB 6 to 32 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified.

Supply & Fix in repairs MCB 40 to 63 Amps capacity, C Curve type suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified.

Supply & Fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 100 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering as per existing is included in quated rate.

Material and labour for sub-main wiring with 2 runs of 6 Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC casing and caping not less than 25 mm wide (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6 Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains including taking up/down old unserviciable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) 2 runs of 6 Sqmm cable, One run of 6 Sqmm earth cable and PVC casing and caping shall be measured and paid as one length only.

Material and labour for sub-main wiring with 2 runs of 4 Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC conduit not less than 25 mm bore with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4 Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains connected with thimble from main DB to sub main DB including taking up/down old unserviciable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) 2 runs of 4 Sqmm cable, One run of 4 Sqmm earth cable and PVC conduit shall be measured and paid as one length only.

Material and labour for sub-main wiring with 4 runs of 10 Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC casing and caping not less than 25 mm wide (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 10 Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains including taking up/down old unserviciable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) 4 runs of 10 Sqmm cable, One run of 10 Sqmm earth cable and PVC casing and caping shall be measured and paid as one length only.

Supply and fixing in repair new generation 1x 20W LED batten fitting, 4 feet lumens efficiency 100 lm / W, Effeciency of driver electronic not less than 85 % , power factor of complete fitting not less than 0.90, Lamp life not less than 50000 operating hours with L 70 criterion .provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired and fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified.

Supply & Fixing LED recess mounted type fitting 36W 2'x2' CRCA LED Slim panel with recess mounting, powder coated white CRCA full glow LED panel including control gear and lamp lumens efficiency 100 lm / W, Effeciency of driver electronic not less than 85 % , power factor of complete fitting not less than 0.90, Lamp life not less than 50000 operating hours with L 70 criterion .provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified.

Supply & Fixing BLDC Five star rated Ceiling fan of size 1200mm sweep complete set with PVC body and louvers connecting up including provn of three core flexible copper wire of size 23/0.0076 from ceiling rose to Ceiling fan including down rod as per existing complete all as specified.

Supply and fix Exhaust fan 450 mm sweep heavy duty metal body AC, 230 volts, 50 Hz and 1400 rpm with lover shutter including cutting hole in wall suitable for fixing fan and finising the surface with plaster 15mm thick in cement mortar (1:4) complete all as specified and directed by Engr-in-Charge.

Supply & Fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete suitable for one single pole MCB 20A 'C' curve all as specified .

Material & Labour for taking down carefully Split AC/Window unit from existing postion & refixing in the new position/ location including providing additional accerssories as required at site, bressing of existing copper pipe with new copper pipe, leak testing, filling gas & commisssioning all as specified and directed by Engineer-in-Charge.

Supply and fix copper tubing of appropriate dia for suction line & for liquid discharge line duly insulated with suitable insulation material including making hole in wall for passing through pipe and making good distrubed surface complete all as specified.

Supply & Fixing Flexible LED strip uses high brightness SMD LED as the light source for indoor application only. It is highly suitable for cove-lighting, decorative lighting complete all as directed by Engr-in-Charge.

Supply & Fixing LED Driver 12 volt DC for LED strip as the light source for indoor application only. It is highly suitable for cove-lighting, decorative lighting complete all as directed by Engr-in-Charge.

Supply and install instant geyser /heater capacity 3 Litres BEE 5 star, 230 volts, AC, 50 Hz including PVC connection of size 15 mm bore 450 mm long for hot water with nuts at both ends complete all as specified.

Supply & fixing decorative wall light fitting made up of polycarbonate, suitable for 15 W retrofit LED lamp (Spiral B-22 base) complete all as specified and directed by Engr-in-Charge.

Supply & Fixing in repairs LED flood light lumens efficiency 10000 lm / W , PDC aluminium housing with aim & adjustable bracket, Modular linear flood light, SMD LED with secondary lens with IP66 Protection with all acessories and fixing arrangement complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 4 feet, 220V, lumens efficiency 100 lm / W and lamp life not less than 50000 operating hours , AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with two Nos of PVC box of size 75x75x20mm for mounting light fittings including connecting up with three core flexible copper conductor cable complete all as specified and as directed.

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( avera Schneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof complete all as specified . Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

jalandhara construction

RAJENDRA CONSTRUCTION