SPL REPAIR TO BLDG NO PH-02 (EXCLUDING ROOF TREATMENT) OF NCO ACADEMY AND PROVN OF 01 NO SENTRY POST NEAR JASRAJ GATE AND TILING OVER STAGE AT WINGATE AUDITORIUM AT DHANA MIL STN.

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thick above or below ground level complete all as specified and directed.

M & L for 40 mm thick PCC 1:2:4, typeB-O, using 12.5mm graded stone aggregate finished fair and even etc, complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) double charged polished, size of each tiles 600 mm X 600 mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile including screed bed or bedding layer of mortar 20 mm thick for laying floor finishes with CM 1:6, complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square or rectangular ) double charged polished, area of each tiles not exceeding 0.36 Sqm in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or cloloured cement to match the shade of the tile, complete all as specifed and directed.

Taking down plaster on brick or concrete surfaces including raking out joints for key and srubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement. in CM (1:6) complete all as specified and directed.

M& L for complete removal of existing treatment by scrapping, wire brushing from old walls and applying two coats of oil bound distemper including preparation of surfaces, complete all as specified and directed.

M& L for complete removal of existing treatment by scrapping, wire brushing from ceiling including cornices, pilasters etc and applying two coat of white wash, including preparation of surfaces, complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description not otherwise description over 10cm width or girth and applying a coat of synthetic enamel paint, complete all as specified and directed.

M&L preparation of old steel surfaces and applying one coats of synthetic enamel paint of any description over 10 cm width and girth, complete all as specified and directed.

Taking down chowkhat or frame n.exc 1.50 sqm with shutters (wihtout taking of shutter from frame ) etc complete all as specified and directed.

Taking down shutters exc 2 sqm each and refixing in same opening, complete all as specified and directed.

Taking down chowkhat or frame exc 1.50 sqm but n. exc. 4.00 sqm with shutters (wihtout taking of shutter from frame ) etc complete all as specified.

S & F for factory solid PVC door frame of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS Square tube as per specified & drawing in opening complete all as specified and directed.

S & F for Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed.

M&L for Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified, supplied and fixed (125x60mm) complete all as specified and directed.

M&L for Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified, supplied and fixed (105x60mm) complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing hold fast, coping, cills and filling in pressed steel door frames including necessary form work and finishing the surfaces to match with existing, complete all as specified and directed.

M & L for 2 nd class hard wood factory made 35mm thick plain framed panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.complete all as specified and directed.

M&L for preparation new or prevously untreated surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

S&F in repairs MS butt hinges of 100 mm size cold rolled mild steel medium weight, ISI marked complete all as specified and directed.

S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F in repair 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply and fixing 125 mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing in repairs 125 mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S & F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S & F in repairs 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing 200mm size mild steel barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed.

Supply and fixing in repairs 200mm size mild steel barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed.

S & F for 300mm mild steel , ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

S & F in repairs 300mm mild steel , ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

Supply and fixing 150mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fixing in repairs 150mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S & F in repair brass chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges, complete all as specified and directed.

S & F in repair Bib taps cast copper chromium plated fancy type with crutch or butterfly handle screwed for iron pipe or for brass ferrule of 15 mm bore dia complete all as specified and directed.

S & F in repair Chromium plated shower rose 125 mm size with swivel joints including fixing to steel pipe or union, complete all as specified and directed.

S & F in repair soap dish vitreous china white approximate size 160 x 160 x 90 fixed to plug with chromium plated brass screw complete all as specfied and directed.

Taking up or down 15 mm bore steel tubing and connections,including cleaning for refixing or removal to store, complete all as specfied and directed.

Refixing 15/20 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), complete all as specfied and directed.

S&F 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specfied and directed.

S & F in repair PVC (SWR) pipe single socketed in any length with rubber ring joints 75 mm dia bore pipe, complete all as specfied and directed.

S & F 75mm dia PVC (SWR) bends any radius, complete all as specified and directed.

Demolition of brick work built in cement mortar of any description incl quions arches but excluding aslars facing complete all as specified and directed by the Engr-in-charge.

M&L for brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

S & F for machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specfied and directed.

M&L for Granite (of any type) work 20mm(+ 2mm) thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment tomatch with shade of granite complete all as specifed and directed by EIC.

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similer shine complete all as specified and as directed.

S & F for galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

S & F in repair galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl. cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specfied and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement sand mortar 1:6 complete all as specified and as directed.

M&L Glazed ceramic colour tiles of size 300 x 450 x7mm thick in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete as specified and directed.

M&L for applying a coat of 1.5 mm thick Birla wall care putty as per manufacture instruction, complete all as specfied and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms, complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including waste coupling, waste pipe and bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm, complete all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular in section wrought screwed with nails area exceeding 13sqcm but not exceeding 25 sqcm, complete all as specified and directed.

M&L in repair for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work in cup board and kitchen cabinet complete all as specifed and directed.

S & F for 25mm dia drapery rod (Poles, finials , ring & bracket complete all as specified and directed.

M & L for complete removal of existing finish on walls including chajjas, facias etc. including filling of holes and applying 1.5 mm thick wall care putty as per manufacturer's instructions and applying two coat of weather proof acrylic exterior paint (100% Acrylic)over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Excavating in trenches not exc 1.5 Mtr wide & not exc 1.5 Mtr depth for foundation etc or for shafts, wells, cesspits, manholes etc and getting out Hard/dence soil, complete all as specified and directed.

Returning, filling in trenches including spreading, levelling, watering and well ramming in layer n. exc 25 mm all as specified and directed by Engineer-in-Charge.

Material & Labour for PCC 1:4:8 type D-2 (with using 40mm graded stone aggregate) in foundation filling and mass concrete, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges fair finished surface complete all as specified and directed.

Material & Labour for RCC M25 as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material & Labour for RCC M25 as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material & Labour for RCC M25 as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material & Labour for RCC M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material & Labour for RCC M25 as in chejjas, complete all as specified and directed.

Material & Labour for Mild steel bars 10mm dia TMT bar and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material & Labour for Mild steel bars 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Moorum/Red Bajri filling in floors/pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed/ rolled including watering to required level and gradient, complete all as specified and directed.

M & L for cement concrete M-7.5 (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate as in sub base of flooring 75 mm thick, complete all as specified and as directed.

M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in floor 50 mm thick finished even and fair without using extra cement, complete all as specified and as directed.

M & L for brick work with sub class 'B' bricks, non-modular sizes as per IS 1077: 1992, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Material & labour for rendering 15 mm thick in two layers on brickwork/concrete surface in CM (1:4) first coat 10 mm thick & second coat 5 mm thick for finished even and smooth (without using extra cement), complete all as specified and directed.

Supply & fixing steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded, incl one shop coated red oxide primer, complete as specified and directed.

M&L for joint free Non-skid ceramic colour tiles7 to 8 mm thick, (square/rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed.

M&L for joint free Non-skid ceramic colour tiles7 to 8 mm thick, (square/rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 10 mm thick backing coat in cement sand mortar 1:4 complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring for light, fan, bell, socket, power socket etc complete with boards outlet boxes fitting and fixture such as switches, sockets, lamps, holders, brackets, ceiling rose etc. and removing from site and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

Disconnecting electric connections and taking down old unsv main switches/DB's steel metal enclosure 02 ways/04ways/08ways/energy meters duly fitted with MCB's cutouts 32 amps capacity including unserviceable wooden boards and making good the disturb surface of the complete all as specified and directed.

Disconnecting and taking down of unserviceable sub main/ service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surface complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store

M&L for point wiring with 1.5 Sqmm PVC insulated, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC trunking of size not less than 32x12mm ISI marked ivory white with all accessories such as tee, bend, joint cover etc/square and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type cast iron or pressed steel terminal box for mounting of switches /sockets regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor,stranded 1.5 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red ,Neutral -Black and Earth-Green directed by Engr-in-charge.

One light point controlled by one, one way, SP, 5 Amps switch

One fan point controlled by one, one way, SP, 5 Amps switch

One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent bd.

One light point controlled by 2- two way switch

One bell/ buzzer point controlled by one push button on same board with other switches or independent with cable 1.5 sqmm

Description all as per item No 90.00 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and including 2.5 sqmm green solid copper conductor cable as continuous earth wire including suitable size of sunk type cast iron or pressed steel terminal box for mounting of modular switches, sockets with modular white cover plate with frame for suitable module as per site requirements complete.

S & F modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

S&F modular socket 6 Amp/16 Amp, 2/3 pin combined, 2 module complete all as specified and directed.

S&F modular switch 6 Amp/10 Amp, 2/3 pin combined, 1 module complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed

Supply & fix modular bell push, 6 Amp,1 module, 240 volt single pole complete all as specified and as directed.

S&F modular switch, two way 5 Amp all as specified and directed by Engr-in-Charge. Make: HPL/Cona/SSK

M & L ceiling rose, 3 pin surface, white /any shade , three terminal. Make : Anchor/Leader/SSK

S&F Bell Multi Music Type, AC 230 volt, Single Pole, complete all as specified and as directed.

S & F lamp holder , insulated body with back plate suitable for batten fittings . Make : Anchor/Leader/SSK

Supply & fix New Adore LED lamps 10W B22 COL BALL LAMP , MAKE Cat part no- LHLDEUEBML8Z010 of HAVELLS or equivalent.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

M&L for refixing/hanging of celing fan and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed.

S & F in replacement of ceiling fan regulators,stepped type AC, 230 Volts complete. Make: Anchor/leader/SSK

S&F MCB DB 8 way, 230 volt, sheet metal enclosure for MCB's, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified. Make: Legrand/L&T/Schnider

MCB SPN 40 amps curve 'C' breaking capacity 10KA

S&F SP 6-32 Amps, curve 'C' breaking capacity 10KA

M&L for two single core PVC insulated unsheathed cable with multi stranded copper conductor of size 6 Sq.mm as sub main including suitable size drawn in & incl PVC trunking not ness than 30/32mm dia ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked, including PVC insulated unsheathed copper conductor cable of size 6 Sq mm as an each continuity conductor complete all as specified and as directed by Engr- In Charge .

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs 5743.75/- ]

m/s mahendra kumar khare contractor

M/S JAINENDRA KUMAR JAIN