REPAIR / REPLACEMENT OF PLY WOOD TOP IN WOODEN BED, TABLE BED SIDE, SOFA SETS, TABLE PEG, CHAIR WRITING, CHAIR EASY, TABLE WRITING, CHAIR DINNING WITH LONG BACK AND OTHER CONNECTED WOODEN FURNITURE FOR OFFICERS MESS AND MARR. ACCN UNDER AFSTN MANAURI

Amount

Chair Dining (FD-279-223) (a) Taking out Unserveceable rear leg from chair dinning Supply & Fixed new rear leg made of seasoned Shisham wood to matching with existing shape & size complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable front leg from chair dinning Supply & Fixed new front leg made of seasoned Shisham wood to matching with existing shape & size complete as specified & directed by Engineer-in-Charge.

Taking out Unsrveceable front/ back rail of chair dinning and Supply & Fixed new front/ back/ side rail matching with existing shape & size completed as specified & directed by Engineer-in-Charge.

Taking out Unserveceable bottom stiffeners from chair dinning and Supply & Fixed new stiffeners made of seasoned Shisham wood matching with existing shape & Size complete all as specified & directed.

Re-Canning of bottom of chair dinning with new 2mm wide half round white plastic cane & Border Canning with 4mm wide plastic cane complete as per specification complete as specified & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing surface of the Chair dining including preparation of old wooden surface complete as specified & directed by Engineer-in-Charge.

Table Dinning 6/8 person(FD-273 &269) Taking out unserveceable table top from table dinning 6/8 person and supply & fix new table top made with 18mm thick pre-laminated MDF board exterior grade confirming to grade-1 & type III (PL MDF-13 Designation) as per IS 14587), one side teak face in Baverian beach shade and balancing white lamination on other side (Make as specified in Particular specifications) including 6mm thick first class hard word (MP teak) edging all around the top complete as shown in drg & directed by Engineer-in-Charge.

Taking out unserveceable/ damaged legs from table dinning and supply & fix new legs of table dinning made of seasoned Shisham wood matching with the existing shape & sizes including PVC or rubber shoe at the bottom of leg to match the existing complete as specified & directed by Engineer-in-Charge.

Taking out unserveceable/ damaged front / back rails from table dinning 6/8 person and supply & fix new rails of table dinning 6/8 person made of seasoned Shisham wood to matching with the existing shape & sizes complete as specified & directed by Engineer-in-Charge.

Taking out unserveceable/ damaged side rails from table dinning 6/8 person and supply & fix new side rails of table dinning made of seasoned Shisham wood to matching with the existing shape & sizes complete as specified & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing surface to the table dinning 6/8 person including preparation of old or new wooden surface complete as directed by Engineer-in-Charge.

Table Peg (FD – 236, 277 AND 25) Taking out Unserveceable top from table peg and Supply & Fixed new top made of 18mm thick pre-laminated MDF board exterior grade confirming to grade-1 & type III (PL MDF-13 Designation) as per IS 14587), one side teak face in Baverian beach shade and balancing white lamination on other side (Make as specified in Particular specifications) including 6mm thick first class hard word (MP teak) edging all around the top complete all as shown in drg complete all as specified & directed by Engineer-in-Charge.

Taking out Unserveceable leg from table peg and S&F new leg made of seasoned Shisham wood including rubber shoe at the bottom of legs fixed with steel screws matching with the existing shape & size complete all as specified & directed by Engineer-in-Charge.

Taking out Unserveceable front/ back rail from table peg and Supply & Fixed new front/ back rail made of seasoned Shisham wood matching with existing shape & size, complete all as specified & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing surface to the table peg including preparation of old wooden surface complete all as specified & directed by Engineer-in-Charge.

Table bed side (FD – 276, 248 AND 28) (a) Taking out Unserveceable back plywood from table bed side and Supply & Fixed new back made of 6mm thick commercial plywood Exterior grade BWR (Make as specified in Particular specifications) complete as shown in drgs as specified & directed by Engineer-in-Charge.

Taking out Unserveceable shelve from table bed side and Supply & Fixed new shelve made of 12mm thick pre-laminated particle board one side teak face Exterior grade (Make as specified in Particular specifications) complete as shown in drg as Specified & directed by Engineer-in-Charge.

Taking out Unserveceable side from table bed side and Supply & Fixed new side made of 18mm thick pre-laminated particle board one side teak face Exterior grade (Make as specified in Particular specifications) duly covered with 4mm thick teak wood beading matching with the existing shape & sizes complete as directed by Engineer-in-Charge.

Taking out Unserveceable top/ bottom from table bed side and S&F new top/ bottom made of 18mm thick pre-laminated MDF board exterior grade confirming to grade-1 & type III (PL MDF-13 Designation) as per IS 14587), one side teak face in Baverian beach shade and balancing white lamination on other side (Make as specified in Particular specifications) including 6mm thick first class hard word (MP teak) edging all around the top matching with the existing shape & size, complete as specified & directed by Engineer-in-Charge.

Chair Writing (FD-1107) M&L for replacement of Front leg of chair writing with first class Shesham wood and fitted or readjusting as per Drg complete chair as specified & shown on Drg as directed by Engineer-in-Charge.

ditto all as per item No 20 above but Rear leg.

ditto all as per item No 20 above but Front/back rail for seat

ditto all as per item No 20 above but Bottom stiffener.

Re-Canning of chair CB with new 2 mm thick half round white plastic cane and Border canning with 4mm wide Plastic cane complete including taking out old damaged cane carefully as specified & shown on drg as directed by Engineer-in-Charge..

Polishing with Hi-gloss French polish to match with the existing surface of the Chair writing including preparation of old wooden surface complete as specified & directed by Engineer-in-Charge.

Chair Easy with Arms (FD-229) M&L in replacement of Front leg of chair easy with second class hard wood shisam and readjusting as per drg complete as specified and shown in drg as directed by Engineer-in-Charge.

ditto all as per item No 26 above but Rear leg.

ditto all as per item No 26 above but Hand Rest.

ditto all as per item No 26 above but Side rail for Seat/back

ditto all as per item No 26 above but Front / Back rail.

ditto all as per item No 26 above but Bottom Stiffner.

Re-Canning of Chair Easy with 2mm wide half round white plastic cane and border canning with 4mm wide plastic cane complete as per specification including taking out old cane complete as specified and shown on drawing as directed by Engineer–in-Charge.

Polishing with Hi-gloss French polish to match with the existing surface of Chair Easy including preparation of old wooden surface complete as specified & directed by Engineer-in-Charge.

Table writing with drawer [FD-249,275 & 33] Taking out Unserveceabletabke top from Table writing and Supply & fixed new table top made with 18 mm thick pre laminated Particle board exterior grade, One side teak face in Baverian beach shade and balancing white lamination on other side Make(as specified in particular specification )including 6 mm thick first class hard wood (MP Teak) edging all around the top complete as shown in drg & directed by Engineer-In-Charge.

Taking out Unserveceable/ damaged legs from table writing and Supply & Fixed new leg made of seasoned Shisham wood matching with the existing shape & sizes complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable/ damaged front or back rails from table writing and Supply & Fixed new rails made of seasoned Shisham wood to matching with the existing shape & sizes complete as specified & directed by Engineer-in-Charge.

Taking out damaged centre stiffener from table writing and Supply & Fixed new centre stiffeners made of seasoned Shisham wood to matching with the existing shape & sizes complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable/ damaged Shutter from table writing and Supply & Fixed new Shutter made of 18 mm thick Pre-laminated particle board Exterior BWR grade one side teak face of Make: Novapan/ Kit Ply sides covered with 4mm thick teak wooden or PVC beading all around the shutter including piano type hinges, 40 mm dia PVC knob & 6 lever steel lock with duplicate key of godrej patteren best quality complete as shown in drg & as directed by Engineer-in-Charge.

Taking out unserveceable/ damaged back plywood from box of table writing and Supply & Fixed new back made with 6mm thick plywood commercial Exterior grade BWR (Make as specified in particular specification ) complete as Shown on drg & directed by Engineer-in-Charge.

Taking out unserveceable/ damaged drawers from Table writing and Supply & Fixed new drawers made with 12mm thick seasoned sheasham wood except bottom & bottomg of drawers shall be of 6mm thick ply wood commercial type BWR grade including PVC or wooden Knob complete as shown on drg & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing complete to the Table writing including preparation of old wooden surface complete all as specified & directed by Engineer-in-Charge.

Cushion for Sofa Set 5 Seater:- 100 mm thick 32 density Cushion with tapestry cloth detachable type using one side suitable zip as approved covered all around with white marking cloth (costing not less than Rs 100 per running metre as approved by GE) duly stitched in each cushion. Cushion shall be covered with approved standard tapestry cloth rate not less than Rs. 550/- to 650/- per running metre and zip of suitable length on any one side of standard quality to facilate change of cover and as approved by Engineer-in-Charge. (Make : Cushions- Sleepwell or Kurlon.

SOFA SET FOUR SEATER (SINGLE SEATER ) FD-234 sheet 1/1 dated 21.7.81 Taking out of defective components from single seater sofa set such as sofa spring, cushion/coir, cotton layer, hession cloth, tapestry cloth, nails, cane stick for fixing the spring etc. and Supply and fixing in replacement of new defective spring, coir of approved quality in seat and back, nails, cane stick for fixing the spring and other necessary componets which are involve for complete repair of sofa and including alround covered with approved standard tapestry cloth rate not less than Rs. 550/- to 650/- per running metre, cotton layer, tapestry cloth as approved by Engineer-in-Charge and as specified in Drg FD-234. Note:- (i) Only defective legs and hand rest shall be measured & paid separetely under respective item No 44 & 45 of this schedule. (ii) Tapestry cloth, hession cloth, tapestry cloth & cushion shall be replaced in all single seater sofa and cost of these shall be deem to be inculde in quoted rates. (ii) Rates of replacement of defective ply, stiffeners, Planks, rails shall be deem to be inclusive in quoted rates. (iv) All wood work and teak veneered surfaces shall be Hi gloss french polished and rates for above shall be deem to be inclusive in quoted rates. .

Supply and fixing in replacement of unserviceable legs of sofa set four seater and providing new legs made out of Ist class hard wood (Teak) duly polished with Hi-gloss French polish.

Supply and fixing in replacement of unserviceable hand rest of sofa set four seater and providing new hand rest made out of Ist class hard wood (Teak) duly covered.

Bed plywood top- FD 246 Repair of Bed plywood top by removing of old unserviceable existing PLY from Bed plywood top & Suply and fixing 12 mm thick new ply wood Waterproof IS marked [Make as specified in particular specification] with eight Nos nut & bolts over Bed plywood top complete as specified in drg & as directed.

M & L for replacement of damaged/broken long rail made out of 1st class hard wood shisham as per drawing of bed plywood top with new parts complete as shown on drawings & all as directed by Engineer-in-Charge.

M & L for replacement of damaged/broken front leg made out of 1st class hard wood shisham as per drawing of bed plywood top with new parts complete as shown on drawings & all as directed by Engineer-in-Charge.

M & L for replacement of damaged/broken rear leg made out of 1st class hard wood shisham as per drawing of bed plywood top with new parts complete as shown on drawings & all as directed by Engineer-in-Charge.

M & L 4mm thick plywood teak facing one side other face commercial type1 quality BWR grade on both side and teak wood bedding all around of head rest of bed ply wood top fixed with head less nails of size 20mm 17 number complete all as specified and directed by Engineer-in-Charge.

M & L for replacement of damaged/broken foot rest all as per drawing of bed plywood top with new parts complete as shown on drawings & all as directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing complete to the Bed plywood top including prepartiaon of old woden surface complete all as specified & directed by Engineer-in-Charge.

Table centre (FD- 174, 235 AND 274) Taking out Unserveceable top from table center and Supply & Fixed new top made of 18mm thick pre-laminated MDF board exterior grade confirming to grade-1 & type III (PL MDF-13 Designation) as per IS 14587), one side teak face in Baverian beach shade and balancing white lamination on other side (Make as specified in Particular specifications) including 4mm thick first class hard word (MP teak) edging all around the top complete all as shown in drg & directed by Engineer-in-Charge.

Taking out Unserveceable leg from table center and S&F new leg made of seasoned Shisham wood including rubber shoe at the bottom of leg matching with the existing shape & size complete all as specified & directed by Engineer-in-Charge.

Taking out Unserveceable long rail from table center and S&F new front/ back rail made of seasoned Shisham wood matching with existing shape & size complete all as specified & directed by Engineer-in-Charge.

Taking out Unserveceable side rails from table center and S&F new side rails made of seasoned Shisham wood matching with the existing shape & size complete as directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing complete to table center including preparation of old wooden surface complete all as specified & directed by Engineer-in-Charge.

Chair Dinning with long back (FD-357) Taking out Unserveceable rear leg from chair dinning long back and Supply & Fixed new rear leg made of seasoned Shisham wood matching with existing shape & size complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable front leg from chair dinning long back and Supply & Fixed new front leg made of seasoned Shisham wood matching with existing shape & size complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable rear/ front/ side rail of chair dinning long back and Supply & Fixed new rear/ front/ side rail made of seasoned Shisham wood matching with existing shape & size completed as specified & directed by Engineer-in-Charge.

Taking out Unserveceable stiffeners from chair dinning long back and Supply & Fixed new stiffeners made of seasoned Shisham wood matching with existing shape & Size complete as specified & directed by Engineer-in-Charge.

Taking out Unserveceable seat from chair dinning long back and Supply & Fixed new seat from chair dinning made with 6mm thick ply wood with 32 density 50 mm thick cushion covered with black racksine (sample approval bt AGE(I) matching with existing shape & size complete as specified & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing complete to chair dinning long back including preparation of old wooden surface complete all as specified & directed by Engineer-in-Charge.

Teapoy wooden (FD – 232, 278 AND 34) Taking out Unserveceable top from Teapoy wooden and Supply & Fixed new top made with 18 mm thick pre laminated Particle board exterior grade, One side teak face in Baverian beach shade and balancing white lamination on other side Make(as specified in particular specification )including 6 mm thick first class hard wood (MP Teak) edging all around the top complete as shown in drg & directed by Engineer-In-Charge

Taking out Unserveceable leg from Teapoy wooden and S&F new leg made of seasoned Shisham second class wood including rubber shoe with screws at the bottom of leg matching with the existing shape & size, complete all as specified & directed by Engineer-in-Charge.

Taking out Unserveceable front/back rails from Teapoy wooden and S&F new front/back rails made of seasoned Shisham second class wood matching with existing shape & size complete all as specified & directed by Engineer-in-Charge.

Polishing with Hi-gloss French polish to match with the existing complete to the Teapoy wooden including preparation of old wooden surface complete all as specified & directed by Engineer-in-Charge.

HAT STAND WITH MIRROR FD-233 Supply and fixing with replacement of old hat stand board with new block board commercial of 18 mm thick pre laminated Particle board exterior grade, One side teak face in Baverian beach shade and balancing white lamination on other side Make(as specified in particular specification )including 6 mm thick first class hard wood (MP Teak) edging all around the frame complete with Hi-gloss French polish to match with the existing complete all as specified, shown on drawing and as directed by Engineer-in-Charge.

Supply and fixing with replacement of old pegs with new pegs of Aluminium anodized and replacement of old mirror with new mirror as per existing size of make Saint Gobain/ Triveni Float Glass/ Atul/ Swastik/Golden fish/ Modi as shown on drg as existing size as per specified directed by Engineer-in-Charge.

SIDE BOARD FD-241,FD-371. Taking out existing old unserviceable top and bottom of side board and providing new top and bottom made out of 18 mm thick pre laminated Particle board exterior grade, One side teak face in Baverian beach shade and balancing white lamination on other side Make(as specified in particular specification )including 6 mm thick first class hard wood (MP Teak) edging all around the top and bottom complete as shown in drg & directed by Engineer-In-Charge.

Taking out u/s ply wood from side board back side and providing new 6mm thick ply wood commercial BWR Gde I including polishing complete.

Removing existing U/S shutter Supply and fixing new shutter double leaf made out of 18 mm thick pre laminated MDF board exterior grade conforming to grade -1 & type III(PL MDF-13 Designation )as per IS 14587), One side teak face in Baverian beach shade and balancing white lamination on other side with continuous hinges cromium plated (Piono) and polishing complete 6mm thick teak wood edging shall be provided 40mm plastic knob superior quality in each shutter shall be provided.

Taking out old unserviceable drawer from side board and providing new drawers made out of 1st class hard wood (Teak) and bottom of 6mm thick plywood commercial BWR Gde I including replacement of 40mm dia plastic knob superior quality in each drawer and polishing complete as directed by Engr in charge .

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material. The contract amount shall be arrived at after deduction of Schedule of Credit from the total quoted amount in BOQ.

Bharat Trading Company

Pleiad Complex On

swastik builders

Yash enterprises

M/s M A Traders