COMBINED COURT BUILDING AT UTHIRAMERUR

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site etc., complete complying with standard specification.

Upto 2.00 M depth from Ground Level

From 2.00 M to 3.00 M Depth

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling Crushed Stone Sand (M-sand) and in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling of conveyed Well Gravel by lorry in basement filling including stacking for premeasurement, conveyance loading and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete as directed by the dept., Officers and complying with standard specification.

Refilling in basement with excavated earth in layers of not more than 15cm thick well rammed watered and consolidated complying with standard specifications.

Cement Concrete 1:5:10 (One Cement, Five M-sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Construction of granular sub base by providing close graded material,mixing in a mechanical mix plant at OMC,carriage of mixed Material to work site,spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density,complete as per clause 401 of MORTH specfication.

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250 mm thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Centering for curved surfaces of all RCC items of work

Providing and laying in position, Standardised Concrete Mix M-20 Grade using M-Sand in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of M-sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

For Superstructure In Ground Floor

For Superstructure In First Floor

For Superstructure In Second Floor

For Superstructure In Third Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Plain Cement Concrete 1:2:4 (one cement, two M-Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Brick work in Cement Mortar 1:6 (One Cement and Six M-Sand) using Fly Ash Bricks of 230 x 110 x 75mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For Foundation and Basement

For Superstructure In Ground Floor

For Superstructure In First Floor

For Superstructure In Second Floor

For Superstructure In Third Floor

Brick work in Cement Mortar 1:5 (One Cement and Five M-Sand) using Fly Ash Bricks of 230 x 110 x 75mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For Foundation and Basement

For Superstructure In Ground Floor

Brick partition walls of 11.00cm thickness using best quality Fly Ash Bricks of size 230 x 110 x 70 mm in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Foundation and Basement

For Superstructure In Ground Floor

For Superstructure In First Floor

For Superstructure In Second Floor

Supplying and laying of Interlocking Paver Block Stone 83mm thick of approved quality and colour Over a base layer of crushed stone sand filling including to full depth of slab perfectly and neat finishing the joints, compressing with vibrator. The rate shall be inclusive of cost of paver block, taxes, incidental charges, transportion charges and labour charges for fixing, neat finishing the joints as directed by the departmental officers etc., complete complying with standard specification. The paver block should got approved by the departmental officers before use on work.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M-Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of BIS quality 160mm dia PVC rain water down fall pipes having a pressure of 4kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be got approved by Executive Engineer before use on works)

Paving the floor with Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality Fine polished steel grey granite slab 1200mm x 600mm, 16mm to 18mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Flammed steel grey granite slab 1200mm x 600mm, 16mm to 18mm thickwith machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Flooring with Design of colour Ceramic Tiles of size 305 x 305 x 6mm laid over 20mm thick cement mortar 1:3 (One cement and Three M-sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK or Equivalent which has to be got approved by executive Engineer before use on works)

Dadooing walls with printed design colour glazed tiles of size 300 x 450 x 8mm of best approved quality, set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be like Johnson / Kajaria / Somany / Nitco / RAK or Equivalent which has to be got approved by Executive Engineer before use on works)

Cladding the verticial wall surfaces with pre-polished granite slab of approved colour 1200 x 600 mm of 18 to 20mm thick of best quality and free from all defects and set in CM 1:2, 10 mm thick. The joints shall be flush with faces of granite slabs and in line, the joints shall be pointed neatly with same colour pigment mixed with white cement of 1.80 kg/m2. The tiles so laid shall be supported with suitable arrangements for a period of 2 hours. The granite slabs shall be got approved by the Deptl.Officers before use in the work etc, complete the rate is including labour, all materials, scaffolding charges, hire charges for granite cutting machine, power consumption etc, complete.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two M-sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Reinforced cement concrete precast slab 25mm thick using 10 to 12mm Chips

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing inposition Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., The door frame inner shall be packed with CC 1:2:4 using 12mm guage HBG stone jelly including fixing the door frames inposition and dimantling the masonry and concrete wherever necessary and redoing the same original condition after fixing including scaffolding charges and labour charges and door frame will be given one coat of Red Oxide primer etc. Complete complying with standard specification The rate shall inclusive of all materials, labour, transportation, loading, unloading, handling, charges etc. The sample of materials should be got approved by the Exe. Engineer before use on works.

Supplying and fixing of Solid Core Flush Shutters with teak plywood on both side with teak wood lipping alround 35mm thick confirming to IS.12406/1989 with 35x12mm T.W.lipping on all edges with necessary adhesive and C.P.Screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevicol, varnish for T.W.lipping thinner colouring agent etc., and aluminium anodised 12m size hinges 3 nos best quality of aluminium anodised fittings of 200mm, towe bolt 150mm 1 no, 20mm aldrops 16mm dia rod 1 no 125mm long handle 2 nos 40mm dia nylon bush 1 no, door stopper 1 no shall be provided. The rate is inclusive cost of fevicol and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete comlying with standard specification. (Single Leaf)

Supplying and fixing of Solid Core Flush Shutters with teak plywood on both side with teak wood lipping alround 35mm thick confirming to IS.12406/1989 with 35x12mm T.W.lipping on all edges with necessary adhesive and C.P.Screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevicol, varnish for T.W.lipping thinner colouring agent etc., and aluminium anodised 12m size hinges 3 nos best quality of aluminium anodised fittings of 200mm, towe bolt 150mm 1 no, 20mm aldrops 16mm dia rod 1 no 125mm long handle 2 nos 40mm dia nylon bush 1 no, door stopper 1 no shall be provided. The rate is inclusive cost of fevicol and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete comlying with standard specification. (Double Leaves)

Supplying and fixing Ornamental Teakwood entrance door with overall size of 3.70m x 2.45m with two leaves have openable shutter and two end portions are fixed as per the design of approved by the departmental officers. The outer frames are three horizontal and four vertical of size 150 x 100 mm teakwood scantlings.The Shutter frames are 100 x50 mm teakwood scantlings. The shutter shall have 2.10m height with two panels using teakwood planks of 40mm thick and finished with approved patten and carving work with skilled carpenter as directed by the departmental officers. The top portion 0.40m height with fixed glazing shall be covered with plain glass of 8mm thick with MS grill.The side fixed portion having bottom 1/3 panaled with teakwood planks of 40mm thick and top 2/3rd with fixed glazing shall be covered with plain glass of 8mm thick with MS grill. The rate includes cost of best and approved quality of Teakwood, Teakwood reeper 50x25mm,carving work, Brass hinges, Tower bolt, Aldrop, locking arrangements, Ornamental Handles, brass screws and labour charges for handlings, fixing charges, conveyance charges etc., The door frame and shutters shall be given two coats of best and approved quality of Lac polishing etc., complete complying with standard specification.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Ground Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Clear size 0.60 x 0.60 x 0.90 M

Clear size 0.90 x 0.90 x 1.20 M

Supplying and filling of 40mm ISS metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit and rainwater harvesting pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc., complete complying with standard specification.

Supplying and filling of 20mm ISS metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit and rainwater harvesting pit to the required thickness as directed by the departmental officers etc. complete. (The rate including cost of metal filling etc., complete complying with standard specification.

Supplying, laying and jointing glazed stone ware pipes of 150mm dia of approved quality with spigot and socket ends and fixing them in dry condition using spun yarn and cement including petty masonry shoring and strutting wherever found necessary and laying the pipe line in the alignment at the specified gradient and testing with necessary tools and plants, etc., and re-filling the trench with excavated earth and levelling the ground etc., complete complying with standard specifications. (Earth work excavation, re-filling with excavated earth will be measured and paid separately).

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Manufacturing, supplying and fixing of Steel doors with following specification. MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwitching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2 Nos, for shtter is provided. 6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. at the top provided. 250x16mm size of Two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear sideof the door at an appropriate place and 1 No. of M.S. handle of heavy duty. A tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. (Single Leaf)

Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work

Supplying and fixing of M.S.grill of approved design for grill gate, grill work to doors and windows openings ramp etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Plastering the surface of walls with Cement Mortar 1:5 (One cement and Five M-sand), 12mm thick with Plasticizer in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M-Sand) 10mm thick with plasticizer including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Supplying and applying of Two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be M-sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then M-sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the departmental officers. (The rates are inclusive of hire charges for grinding machine with wheel, cost of M-sand paper (water proof abrasive sheet) cost of putty blade, labour charges for grinding the joints and M-sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc., complete). The putty should be got approved by the Executive Engineer before use on work

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three M-sand), 20mm thick with Plasticizer in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting the exterior walls with Texture Finish Paint of approved quality and colour including through scrapping, clean removal of dirt etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of Textured paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing of angle of size 50mmx50mmx6mm including dismantling laying, concrete for fixing the Angles and lying the barbed wire etc., complete including one coat of primer etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing of Barbed wire -10 Gauage - Two ply and four pronged (Galvanised) including cost of transport, cutting etc., complete complying with standard specifications and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed Plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two M-sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White Glazed Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best quality and approved make Indian made White glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC Fibre Glass framed 600x450x5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).

Supplying and fixing position CI Nahani Trap of the size 100x75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M-sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M-sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia Pillar Taps (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

32mm dia Gun Metal Gate Valve

25mm dia Gun Metal Wheel Valve

Supplying and fixing in position best quality of Astral foamcore pipes of stiffness class SN8 of BIS mark and providing leak proof joints using adhesives including fixing to the wall special clamps, teakwood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The pipes should be got approved by the Executive Engineer before use on works).

200mm dia pipe

160mm dia pipe

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia PVC soil / waste pipe

75mm dia PVC soil / waste pipe

Supplying and fixing in position of the following PVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc, including fixing to walls with necessary teak wood plugs screws etc. and giving connections to the PVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc. complete complying with standard specifications. (The PVC specials should be got approved from the Executive Engineer before use on works).

160mm dia PVC Door Elbow

160mm dia PVC Plain Bend

110mm dia PVC Door Elbow

110mm dia PVC Plain Bend

110mm dia PVC Door Tee

75mm dia PVC Door Elbow

75mm dia PVC Plain Bend

75mm dia PVC Door Tee

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. (Above Ground Level) (Internal Water supply)

32mm dia UPVC pipe

25mm dia UPVC pipe

20mm dia UPVC pipe

Supplying and fixing in position of the following UPVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc, including fixing to walls with necessary teak wood plugs screws etc. and giving connections to the UPVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc. complete complying with standard specifications. (The UPVC specials should be got approved from the Executive Engineer before use on works).

32mm dia UPVC Tee

25mm dia UPVC Tee

20mm dia UPVC Tee

32mm dia UPVC Elbow

25mm dia UPVC Elbow

20mm dia UPVC Elbow

32 x 25 mm dia UPVC Reducer Tee

25 x 20 mm dia UPVC Reducer Tee

20 x 15 mm dia UPVC Reducer Tee

25 x 20 mm dia UPVC Reducer Elbow

32 x 25 mm dia UPVC Reducer Elbow

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation methord using rotary rigs fuel, labour for drilling bentonite and water required for drilling at site (Site will be shown by the TWAD Board Officers) including construction of mud pit.

Upto 60 m Depth ending below ground Level

From 60 m to 90 m Depth ending below ground Level

From 90 m to 120 m Depth ending below ground Level

From 120 m to 150 m Depth ending below ground Level

From 150 m to 180 m Depth ending below ground Level

From 180 m to 210 m Depth ending below ground Level

Reaming from 140/150mm dia pilot bore to 300mm dia bore as directed by the Departmental Board Officers.

Upto 60 m Depth ending below ground Level

From 60 m to 90 m Depth ending below ground Level

From 90 m to 120 m Depth ending below ground Level

From 120 m to 150 m Depth ending below ground Level

From 150 m to 180 m Depth ending below ground Level

From 180 m to 210 m Depth ending below ground Level

Supply of 160 mm PVC Special Blue casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.

Supply of 160 mm PVC Special Blue Slotted casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including the jointing the pipes with PVC couplers with cement paste etc., complete

Charges for developing the borewell with air compressor 300 CFM Capacity (minium 8 hrs) including transportation labour and fuel charges for compressor as directed by the Departmental Officers and condicting yeild test by 'V' Notch Method

Supplying and fixing 5 HP / 3 Phase, 9 Stage sub mergible pump of approved make and quality with ISI mark with necessary accssories and fixed with delivery pipe errected in the borewell with necessary clamp etc., with following additional accssories. 1 No of 3 Phase Star Delta Starter of 63 AMPS of approved quality and make with ISI mark. 1 No of 3 Phase 63 AMPS Main Switch of approved quality and make with ISI mark. 1 No of priventor of approved quality and make with ISI mark. 1 No of pannel board of required size with indicator fuse unit voltmeter with necessary provision toaccomodate the starter and mini starter etc. 1 No of capacitor with board as per standards of TNEB.

Supplying and fixing 3 HP / 3 Phase, 9 Stage sub mergible pump of approved make and quality with ISI mark with necessary accssories and fixed with delivery pipe errected in the borewell with necessary clamp etc., with following additional accssories. 1 No of 3 Phase Star Delta Starter of 63 AMPS of approved quality and make with ISI mark. 1 No of 3 Phase 63 AMPS Main Switch of approved quality and make with ISI mark. 1 No of priventor of approved quality and make with ISI mark. 1 No of pannel board of required size with indicator fuse unit voltmeter with necessary provision toaccomodate the starter and mini starter etc. 1 No of capacitor with board as per standards of TNEB.

Supplying fixing and connecting of 4 sq.mm seathed 3 core cable wire for the sub-mergible motor from pannel board to sub-mergible pump including rope etc., complete.

Supplying and fixing 32mm dia HDPE pipe for sub-mergible pump in Bore well (class-5 1 MPa or 10 Kg / cm2 pressure) of best approved quality including welding wherever necessary etc., complete as directed by the Executive Engineer. The pipe should be got approved by the Executive Engineer before use on works.

Supplying, fixing of cylindrical vertical notational polythene water storage tank of 2000 litres capacity confirming to I S. 12701 / 96. the tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simply pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank etc., and the tank should be fixed firmly as directed. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., ( The water tank should be got approved by the Executive Engineer before use on works)

Providing rain water harvesting recharge Perculation pit for a total depth of 1.95m,for which 0.45m depth in natural soil pit with 0.80m dia balance depth (well ring size of dia 0.90m and 0.30 depth) covered with RCC cover slab of 75m thick of 1.00m dia and thus the top of well ring kept 0.15m above the ground level, and filling the rechargepit with sand and 40mm for 0.30m depth and 1.05m depth respectively and balance depth of 0.60m is kept as freeboard for RCC percolation pit. the rate includes cost of all materials such as Rc well ring, Rc cover slab, 40mm HBS jelly sand at site of work and labour charges for fixing wellring, cover slab in position and filling sand and 40mm metal.

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specification.

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works provided by Armstrong over the lowest and second aluminium section at an on centre distance of 600mm. Place the inside clip on the groove end of the panel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure.

Supplying and Fixing of Aluminium Dye Cast Letters of 9" size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process.

Providing and Fixing of Brass Tamil Nadu Government Emblem of size 45cm (15") dia in position of best quality special approved variety for name board including moulding, grinding and neatly finishing to all edges to letter conveyance charges bolts and nuts, paste and scaffolding charges the same in position etc., complete.

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. as directed by the Engineer incharge and including cost of chemicals labour transportion etc, Stage:1 Spraying Anti-termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation. Stage:2 Spraying anti-termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth. Stage:3 Spraying anti-termite chemicals solution on sand for the flooring before laying the flooring concrete. The treatment has to be carried out on the sand filling the basement after leveling operation is over. Stage:4 Spraying anti-termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12" to a depth of 8" around the building before laying the plinth projection. This holes has to be be closed after the treatment.

Providing the safeguard for the columns for 1m height with rubber corner guard of 3" x 3" L type colour of black and yellow approved quality etc., complete complying with standard specification and as directed by the departmental officers.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Modular Kitchen floor unit made Plywood : 18 mm BWP & Commercial Plywood - Rolex Gold or Fortune Gold, Laminate : Virgo , Green Lam, Hardware Hinges & Runners : Sleek / Kitchen - soft closure / rest all Normal hinges, Finishes : Glossy, Matt - 2mm Edge Banding Factory Finish, Double Side Grey Laminate with 0.8mm Edge Tape for Entire Carcass using 18mm and 6mm HDHMR sheet finished in PU polis etc., complete.complying with standard specifications and as directed by the departmental officers.

Modular Kitchen Sleek Kitchen Accessories - Cutlery Tray, Plain Basket, Thali Basket, Oilpullout, Wicker Basket etc ., complete complying with standard specifications and as directed by the departmental officers.

Supply and Fixing of steel racks of size 900X450X2100mm of record racks with 6 compartments using MS angle of size 55X55X8mm @ 6.4kg/m for outer leg 4 nos intermediate shelves support MA angle of size 40x40x6mm @ 3.5kg/m holes of 6mm and are drilled proerly to accommodate the fitness,. Galvanised lor sheet panels of size of 900x450mm folded at the corners are made form 16g (1.60m) @ 12.50kg/m2 slabs in necessary height and panels folded soded are made to accommodate the fastness. 6 panels are provided for each rack and can be placed at different height in the racks as per the conveience of the user department., upto stiffened panels to the legs. The mild steel legs are given two coats of SEP on two coats over one coat of primer. The rate including cost of all materials, labour chaarges, etc., complete complying with standard specifications and as directed by the departmental officers.

Manufacturing and supplying of teak wood conference chair with PC knitted seat and back with good polish finish.

Manufacturing and supplying of teakwood witness box of size 3' x3' x4' - 6' height made of 19mm BWP plywood with melamine finish.

Manufacturing and supplying of teakwood accused dock type of 5' x 3' x 4' made of 19mm BWP plywood with melamine finish.

Manufacturing and supplying of ornamental teakwood Judges Dias of 0.80m height including step side & area side accused box, Judge stage 4550 x 1640 x 600mm - for 1m height & barricade 7000 x 1000 x 1000mm - 1200mm height

Manufacturing and supplying of teakwood dias table of size 15'x3'x2'6" made of 18mm teakwood commercial plywood, 4mm OST ply with melamine polish finish.

Manufacturing and supplying of konguwood dias of 10'x8'x1' small diad with 25mm plywood top.

Manufacturing and supplying of teakwood Judge chamber crown chair

Manufacturing and supplying of modular table with a drawer, cupboard, CPU provision and keyboard arrangements using 19mm BWP plywood both sides 1mm lamination sheet with sheelac polish.

Providing office Table Size of 48" x 24" with frames of 1" 18 gauge CRCA square tubes and the drawer and box 18 gauge CRCA sheet. Top of 19mm hardwood ply with laminated top, corner rounded or SS corner clamp to be fixed ISI grade locks, SS handles necessary bushes to be fixed. The rate includes cost of all materials, fabrication,transports and other incidental charges, including providing in the position as directed by departmental officers.

Manufacturing and Supplying G type chair made out of teak wood PC knitted seated back with good polish finish

Supplying of fully upholstry sofa 3 seater made out with 100mm foam for seat and 75mm foam cushion for back in fabric finish.

Manufacturing and supplying Executive Table of size 5'6" x 2'6" to a height of 2'6", made out of 25mm thick exterior grade Both side Pre laminated wood particle board with duck nosing on two sides (ISI & ISO Certified) for the table top and 18mm thick exterior grade Both side Pre laminated wood particle board (ISI & ISO Certified) for all other vertical planks the table includes 1 No. of Drawer, 1 no of Cupboard with lock & key in one side and 3 no of drawers with 3 in 1 lock and key on the other side the partical board cutting edges are finished with PVC edge banding. The rate includes cost of all materials, fabrication,transports and other incidental charges, including providing in the position as directed by the departmental officers.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

100 mm dia

80 mm dia

25 mm dia

Supply, erection, testing and commissioning of Cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers.Make:NORMEX/KARTAR

100 mm dia spindle sluice valve

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 . including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers.

100 mm dia Non-return valve

Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: KIARTAR / OMEX / EQUIVALENT)

Supply, erection, testing and commissioning of Air release valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers.Make: KARTAR / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14kg range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers.Make: H- GURU / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfos or Donfos including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start & auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers. Make: DONFOSS/ INDFOSS / ISI MAKE / EQUIVALENT.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate)powder type Fire Extinguisher of 6 kgs capacity as per IS:15683 with pressure gauge,discharge hose& control nozzle,wall mounting bracket,safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers.Make: EXCELLENT/SAFETY FIRST / EQUIVALENT

Supply and fixing of carbon-di-oxide Gas type 2 kg capacity Fire Extinguisher as per New IS No. 15683 complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the departmental officers. Make: EXCELLENT/SAFETY FIRST / EQUIVALENT

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil)

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with Necessary wall opening and making good of the wall.

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 2 x 4 feet 18W Twin crystal glass LED tube light with TW round blocks on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting with LED tube.

Supply and fixing of single box type 1x18w /22 W 4 feet LED Fitting without LED Tube complete with TW round blocks on wall or ceiling with 20 W LED tube light with single side connection ( Havells / equivalant) with PVC unsheathed Copper leads from terminals to the fitting.

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 300mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 3nos.6A two module socket , 1 no. 6/16A two module socket , 3 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 25A Flush type Wall Socket 25A DPMCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 48 W LED street light fitting complete with 32 mm dia G.I pipe (Class "B") with 1 No 32 mmdia GI Bend complete on the existing post / wall with PVC unsheathed copper leads MS clamps and aluminium painting

Supply and fixing of 150W LED flood light fiting complete with angle iron frame supports with suitable clamp sets on the existing post / wall with PVC unsheathed copper leads MS camps and aluminium painting.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.The MCB DB and MCB’s should be like Standard Make

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.

Supply and run of 4 of 16 sq.mm. PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 16 Sq.mm Copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 10 KVA Online ups single phase in single phase out with 2 Hours backup.

Supply and demonstration of 2 KVA inverter with input Voltage range 180V -260V and output Voltage 200V-230V 50HZ with micro controller based design like microtek/ equivalent with 2 Nos 12V -150AH Exide battery/ equivalent and testing complete.

Supply and fixing of 32A DP MCB in flush with sheet enclosure in wall with earth connection [Legrand (MDS) / Hager (L&T) make]

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 60W LED street light fitting with LED (Lower end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

Supply and Fixing of Minimast (12 Metre) with 6 Nos.150W LED Fitting.

Supply and Run of 4 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 32A FP MCB in flush with sheet enclosure in wall with earth connection

Erection of the MiniMast by Providing Concreting 1:2:4mix R.C.C masonry foundation pedestal. The RCC Pedestal projection should be 30cms above the ground level, The Switch feeder box should also be mounted in RCC pedestal with projection of 30cms above the ground level suitable to the safe bearing capacity of the soil at 12T/ M2 at 1.5m depth of below ground level and necessary galvanized foundation bolts nuts washers and Anchor Plate. Template etc: complete as per standard specification of IS-875-1987

Supply and fixing of hot dip galvanized lightening arrester and necessary accessories etc: complete as per standard specification

Supply and fixing of Aviation Lamp fitting with Base and coupling arrangements etc: complete as per standard specification (Make; Philips/Bajaj/Crompton/Equivalent)

Supply and fixing of 4 Mtr Air Termination rod 16/10mm (Lightning Rod)

Supply and fixing of Aluminium alloy solid round conductor with 8mm dia of material AlMgSi as per IEC 62561-2 With conductor Holder, glue, connectors, joints etc.

Supply and fixing of Rust Resistant non Corrosive 10mm dia copper bonded steel round conductor for earth termination

Supply and Fixing of S.S Conductor holder

Supply and run of 25mm x 6mm GI Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection

Supply of S.S Test Joint

Supply and insallation maintenance free Earthing with Copper rod of 17.2mm dia and 3m Length.

Supply and fixing of Lightning Counter -LCD Display and battery.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

supply and fixing of timer clock and 32A three phase contactor arrangement for the automatic on/off of the street lights

Supply and run of 2 of 1.5 sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 1000W automatic electric water heater of 25 litres capacity suitable for 230V 50c/s AC supply on suitable MS clamps with 3 core flex wire,but without plumbing work.

Supply and fixing of 32ATPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only [canteen]

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32 A neutral link and earth link (1"x1/8"copper flat)on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and interconnection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection.[Canteen]

Supply and Run of 4 of 10 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade on 7/20 GI wire for service connection mains[Canteen+ 2 Nos Quarters]

Supply and Run of 4 of 10 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in 25mm dia GI pipe (class B ) suitably bent at both ends with necessary angle iron upright and end support for service connection mains

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.

Supply and fixing of 63A TPNMC switch with Suitable angle iron frame work with MS Cable entry boxes with earth connection only [Quarters 1 & 2]

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feetx1-1/2 feet using angle iron of size 1-1/2"x1-1/2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos.63 A fuse units (500V), 1 No. neutral link, copper earth flat of size 1"x1/4" with interconnection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with 1 No 63 Amp 30MA Four Pole RCD/ RCCB (Higher End) withsuitable necessary connection with earth connection complete.[Quarters 1 & 2]

Supply and fixing of 100A TPN sheet double break switch with HRC fuse and neutral on suitable angle iron frame work with earth connection only.[Quarters Lift Only]

Supply and fixng of TNEB meter board suitable for 3 phase100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size2 feet x1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos.100A fuse units (500V), 1No.neutral link, copper earth flat of size 1"x1/4" with interconnection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete.[Quarters Lift Only]

Supply and clarnping of 3-1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.[Quarters Eb meter to pole]

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and erection of 2.0 Ton capacity ( 3star Rated) Split type Airconditioner unit confirming to ISI 1301 (part-2) 1992 with amendment No.1 fitted with Hermetically sealed compressor operationon 230V 50Hz AC supply system with refrigerant gas R-22 suitable for high wallmounting evaporator and specification as under general requirement interconnection of pipes and cable.

Supply and erection of 5KVA capacity Automatic Voltage stabilizer suitable to operation on 230 volts, single phase,50Hz,AC supply system with tie delay relay and High/Low voltage cut off, input voltage range 170V to 270V AC single phase, wall mounting type stabilizer with necessary clamp.

Supply and laying of 5/8'' and 3/8'' copper pipe (Extr beyond 3Mtrs supplied with AC Unit)(For split AC Unit)

Supply and Fixing of MS stand for fixing outdoor units.(For Split outdoor unit)

Supply and fixing of UPVC trunking box with cable divider.

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 no 10 person judge Quarters lift as per the following specifications (Gearless lift with machine room), (1)Location: proposed Judge Quarters at Uthiramerur, (2)No of lift: one no. (Gearless), (3)Type of lift: Bed-Cum passenger, (4)Capacity of lift: 10 persons / 544 Kgs, (5)Speed: 1.5 m/ Sec, (6)Type of drive: V3F drive with enhanced ride comfort and near zero level functions, (7)No of floors: GF+2 Floor, (8)Total travel: 3.3 mts x 3 Landing =9.9 mts, (9)Leveling accuracy: high level accuracy with smooth and jerk free stopping, (10)Construction of CAR: No. 4 hardened sheet high quality stainless steel car and hand rail granite flooring and Perspex false ceiling, (11)Position of machine: directly above the lift well, (12)No of landing service: One in the front side- 1 no., (13)No. of car entrance: one in the front side only, (14)Car entrance door: power operated automatic V3F drive center opening sliding SS door, (15)Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings., (16)Lift well :Lift well size : 2100 mm wide x 1650mm depth (existing) RCC construction with brick masonry, (17)Lift pit depth:1800 mm, (18)Car size: 1300 mm wide x 1100 mm deep x 2200mm height, (19)Lift machine room size: as per ISI 14665 (part 1)2000 to be constructed by PWD civil wing over the lift well, (20)Power supply: 400 / 440 v three phase 50 Hz AC supply for power and 230 V 50 Hz single phase power supply for light, (21)Control: micro computer (micro processor):based simplex collective control with / without attendant, (22)Car fittings: CFL lighting with 1 no 300 mm sweep cabin fan,

(23)Lift well: RCC construction with brick masonry to be constructed by PWD civil wing, (24)Induction: UP / DOWN digital direction and position indicator for all landings and inside the car, (25)Emergency alarm bell: battery operated bell to be provided with automatic charging device, (26)Emergency light: battery operated light to be provided with automatic charging device, (27)Fire mans switch: to be provided at the GF, (28)Minor builder works: to be provided by the lift contractor, (29)Scaffoldings: to be provided by the lift contractor, (30)Sill angles and facia plates: SS to be provided by the lift contractor, (31)Steel for lift machinery: to be provided by the lift contractor, (32)Servicing and maintenance: free comprehensive servicing and maintenance for one year Guarantee period to be provided by the lift contractor, (33)Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories, (34)Provision for intercom with phone: to be provided by the lift contractor, (35)lift license: preparation of drawings payment of charges to CEIG and insurance policy if any and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor, (36)Floor position announcer: to be provided by the lift contractor, (37)Special features (a)Infra red door sensor with full height screen, (b)Full width half height rear panel mirror, (c)Tubular SS hand rail in car, (d)Stainless steel signal features, (e)Vandal proof SS button with SS cover, (f)SS door frames for landing doors , (g)V3F door operator, (h)Call register signal,

(i) Stainless steel facia plates for car operating panel and landing fixtures, (j) Steel ladder for lift machine room, (k) On / off switch for fan and light, (l) Over load warning indicator with audio announcer, (m)Voltage stabilizer for control circuits, (n)Braille button (38)Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries, (39)Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor, (40)Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department, (41)Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year.

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 no 13 person public lift as per the following specifications (Gearless lift with machine room) (1)Location: proposed court at Uthiramerur Court, (2)No of lift: one no. (Gearless), (3)Type of lift: Bed-Cum passenger, (4)Capacity of lift: 13 persons / 680 Kgs, (5)Speed: 1.5 m/ Sec, (6)Type of drive: V3F drive with enhanced ride comfort and near zero level functions, (7)No of floors: GF+2 Floor, (8)Total travel: 3.3 mts x 3 Landing =9.9 mts, (9)Leveling accuracy: high level accuracy with smooth and jerk free stopping, (10)Construction of CAR: No. 4 hardened sheet high quality stainless steel car and hand rail granite flooring and Perspex false ceiling, (11)Position of machine: directly above the lift well, (12)No of landing service: One in the front side- 1 no., (13)No. of car entrance: one in the front side only, (14)Car entrance door: power operated automatic V3F drive center opening sliding SS door, (15)Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings., (16)Lift well :Lift well size : 2400 mm wide x 3200mm depth (existing) RCC construction with brick masonry, (17)Lift pit depth:1800 mm, (18)Car size: 1500 mm wide x 2400 mm deep x 2200mm height, (19)Lift machine room size: as per ISI 14665 (part 1)2000 to be constructed by PWD civil wing over the lift well, (20)Power supply: 400 / 440 v three phase 50 Hz AC supply for power and 230 V 50 Hz single phase power supply for light, (21)Control: micro computer (micro processor):based simplex collective control with / without attendant, (22)Car fittings: CFL lighting with 1 no 300 mm sweep cabin fan,

(23)Lift well: RCC construction with brick masonry to be constructed by PWD civil wing, (24)Induction: UP / DOWN digital direction and position indicator for all landings and inside the car, (25)Emergency alarm bell: battery operated bell to be provided with automatic charging device, (26)Emergency light: battery operated light to be provided with automatic charging device, (27)Fire mans switch: to be provided at the GF, (28)Minor builder works: to be provided by the lift contractor, (29)Scaffoldings: to be provided by the lift contractor, (30)Sill angles and facia plates: SS to be provided by the lift contractor, (31)Steel for lift machinery: to be provided by the lift contractor, (32)Servicing and maintenance: free comprehensive servicing and maintenance for one year Guarantee period to be provided by the lift contractor, (33)Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories, (34)Provision for intercom with phone: to be provided by the lift contractor, (35)lift license: preparation of drawings payment of charges to CEIG and insurance policy if any and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor, (36)Floor position announcer: to be provided by the lift contractor, (37)Special features (a)Infra red door sensor with full height screen, (b)Full width half height rear panel mirror, (c)Tubular SS hand rail in car, (d)Stainless steel signal features, (e)Vandal proof SS button with SS cover, (f)SS door frames for landing doors , (g)V3F door operator, (h)Call register signal,

(i) Stainless steel facia plates for car operating panel and landing fixtures, (j) Steel ladder for lift machine room, (k) On / off switch for fan and light, (l) Over load warning indicator with audio announcer, (m)Voltage stabilizer for control circuits, (n)Braille button (38)Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries, (39)Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor, (40)Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department, (41)Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year.

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with Painting of suitable colour.

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigd pipe on wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire with painting of suitable colour.

Supply and fixing of digital ISDN EPABX system with 896 Nos of analog extension 8 nos.of digital junction 400 nos.of expandable port 2 Nos. operator console and compliable ISDNQ IP net working system specification for PCM/TDM Technology 32 bit microprocessor caller id on digital and IP as well as analog extension ISDN PRI/BRI boss secretary feature operator console for multilingual menu driven and keys name display on LCD.

Supply and fixing of RJ 11 I/O socket with Cat 6 PVC Modular box suitable Face plate single socket RJ-45

Supply, fixing and termination of 200 pair DB with krone module and necessary connections.

Supply, fixing and termination of 100 pair DB with krone module and necessary connections.

Supply, fixing and termination of 20 pair DB with krone module and necessary connections.

Supply, fixing and termination of 10 pair DB with krone module and necessary connections.

Supply and laying of 0.5mm 50 pair telephone cable with suitable PVC pipe make: Delton/ eq.

Supply and laying of 0.5mm 20 pair telephone cable with suitable PVC pipe make: Delton/ eq.

Supply and laying of 0.5mm 10 pair telephone cable with suitable PVC pipe. make: Delton/ eq.

Supply and laying of 0.5mm 2 pair telephone cable with suitable PVC pipe. Make: Delton / eq.

Supply and Installaion of caller ID telephone instrument. Make:Betel/Eq.

Supply and run of 1 of CAT 6 cable in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

Supply and Installation of 8 ports Unmanaged 10/100/1000 LAN network switches

Supply and fixing of 4 U rack

Supply and fixing of 4 MP POE IP Bullet/Dome Camera

Supply and fixing of 32 Channel network video recorder for CCTV

Supply and fixing of 8 port PoE Switches for CCTV IP camera

Supply and fixing of Hard disk for NVR

Supply and Fixing of Sony Bravia LED TV 139CM(55 Inches) 4K Ultra HD Smart LED Google tv KD-55X74L (Mrp:99900-18% GST)

Supply and Fixing of 20W Ceiling Speaker.

Supply and Fixing of Chairman Unit.

Supply and Fixing of Cordlesds Mic UHF.

Supply and Fixing of PA Mixer Amplifier 240W.

Supply and Fixing of 2 Core 1.5 Sq.mm Shielded Copper Speaker wire.

Supply and Fixing of 8 Core 1.5 Sq.mm Shielded Copper Speaker wire.

Supply erection testing commissioning of 250A capacity floor mounted powder coated Cubical panel of size 5' x 4' made from 16 SWG CRCA sheet steel material supported on 2" x 2" x 1/2" MS angle frame work. The Bus bar chamber shall be designed to accomodate 8 Nos. switch compartment of size 1' x 1 1/2' x 1' with 2 Nos of switch chamber and cable chamber. The Bus bar chamber to be provided at the middle and on both sides of Bus bar chamber Switch chamber and Cable chamber to be fabricated. The 4 Nos. of tinned copper bus bar are of size 1" x 1/2" for 3 Ph. & N & Interconnection covered with coloured sleeves mounted on suitable bus insulators support for bus bar with hylem sheet separation for bus bars and switches. The 2 Nos. of tinned copper bus bar are of size 1" x 1/2" shall be mounted inside around the bus bar chamber. The inter connection of incoming switch from bus to switches, incoming terminals is with 1" x 1/2" tinned copper flats for interconnection to outgoing switch terminals with the following accessories mounted on industrial hylum sheet of 12mm thick with painting of one coat primer and two coats of power coating, with super scribing of cable size / switch location etc. with danger board. (1) INCOMING:250 Amps TPN SDFU in sheet steel Double break with HRC Fuses - 1 No, (2) OUTGOINGS: 63A Amps TPN SDFU in sheet Double break with HRC Fuses - 10 nos, (3)Bus bar chamber made up of 16 SWG Sheet steel with suitable angle iron frame work, made with 37.5mm x 37.5mm x 6.24mm Size MS angle iron complete for fixing the busbars, (4)1"X1/2" Tinned copper flat for 3 phases, neutral , mounted on suitable insulators / seperators,

(5)1"X1/2" Tinned copper flat for 3 phases, neutral , mounted on suitable insulators / seperators, (6)1"X1/8" Tinned copper flat for earth flat mounted at the back to the entire length of the busbar chamber, (7)No. 6 Hard Drawn copper conductor for 3 phases, neutral , mounted on suitable insulators / seperators, (8)Inter connections to (a) 250A TPN switches with 2"X1/4" Tinned copper flat.(b) 63A TPN switches with No.8 HD copper Interconnection. (9)All switches with 2nos. Earth connections with suitable copper. (10)Erection of the panel on wall by grouting and finishing., (11)Painting of the panel with one coat of metal primer & two coats of enamel paint, (12) Danger Board & marking of all switches. (at proposed main essential panel board at electrical room)

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps/ supports on wall/floor/ground for earth connection.

CT meter box of size 1.25m x 1.0m x 0.23m consisting of 3 chambers 1) meter board with hylem sheet of 12mm thick with ms sheet of size 45cm x 45 cm 2)measuring kit consisting accessaries needed by TNEB 3) Bus bar arrangements with 40mm x 6mm tinned copper bar with bus supports, S & F of CT coils of suitable rating as required by TNEB 4)Erection of the box with suitable AI frame work and suitable masanary pedestal 5)Painting and marking 6)2 nos. earthings as per PWD standard

Supply and fixing of 250 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and clarnping of 3-1/2 x 150 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply , Testing Commissioning and Handing over of 1 No 160 KVA Diesel Generator set of 0.8 P.F. Three phase 415V/ 420 Volts, 50Hz, 1500 RPM CPCB Approved capacity comprissing of Kirloskar Engine model 6R 1080TA developing 154 BHP water cooled clock wise rotating feed pump with 100KW/ 160KVA operating capacity brushless alternator close coupled underneath fuel tank standard safeties LLOP with stop solenoid battery with lead Electric start and vibration fitting and accessories and AMF panel as detailed below including transporting & unloading charges.(A)Engine: Water cooled diesel engine suitable for Generator application with a shaft out put of 154BHP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling fly wheel, ai cleaner, fan blower, radiator, water pump, fuel filter, lubricating oil filter, etc., (B)12/24 Volt Electronic starting Equipment:Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length, (C) ENGINE INSTURMEN PANEL / MOUNTED: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechanical), (D)ALTERNATOR: 125KVA/100KW Capacity of brushless alternator, AC 3 phase, 50Hz, 415/420V, 0.8 PF, 1500 RPM under NTP conditions, conforming to IS:13364 (Part-II)/ 1992 to be means of coupling, (E) AMF CONTROL PANEL:The AMF control panel (cubical) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front doors with enamel painted and incorporating the following with suitable provision for

(28)1set Timers, (29)Audio and Visual indicator arrangements for: (a)Low lubricating oil pressure, (b) High water temperature, (c)Over speed, (30)1No Earth fault relay, (31)Isolator to isolate the neutral Note:- 1. The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements, (2)The engine should trip for the following:(a)Low lubricating oil pressure, (b) High water temperature, (c) Over speed, (3)Supply and fitment of Auto Mains Failure Panel, 1 EB Service wih 200 Amps switch and contactors SUF Control relays, timers etc suitable for auto change over of DG & EB Service. (F)FUEL TANK Fuel tank of 200 litres capacity and with inlet and outlet connections, level indicator with scale etc. (G)BASE FRAME:Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting of generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame wih proper alignment, (H) ACOUSTIC ENCLOSURE:The Acoustic enclosure, Self standing weather proof KG- CPCB Typed Acoustic canopy KG 250WS floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions. Erection of acoustic enclosure suitable for 250KVA Diesel generator complete with all accessories as above and suitable supports etc. 1. Supply of manuals for operation & maintenance of DG set with warranty card etc.

Erecion of Get set:- Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion around the foundation erection of 160KVA Generator set over the exisiting foundation and erection of Generator set with proper alignment over the existing foundation to suit 250KVA Generator set Foundation size L4200xW1600xH200mm.

Supply and installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the generator room with necessary thermal insulation

Supply and installation maintenance free GI Earthing system comprising of 50 mm dia and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25kgs of carbon based environment friendly backfill compound and suitable clamp (chemical Earthing)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply of tools such as1 no 15" cutting piler , 1no 6" screws driver , 2 nos 9" screw driver , 1 set 6 nos double ended spanner ,1No 1/2 ip hammer , 1No panner for removing engine oil plug 1no line tester required for the mainttenence and operation of generator set -1 set

Supply and demonstration of the following safety accessories, (a)1 meter x 1 meter x1/2 inch 11kv rubber mat - 2 nos, (b)one set of 4 nos. 9 liters fire buckets with metal stand frame - 1set, (c) first aid box with medicine - 1no, (d) 11 kV rubber hand gloves - 2 nos, (e)2 Kg capacity dry powder type fire extinguishers - 2 nos, Hand operated pump to transfer fuel from standard barrel to fuel tank - 1 no, (g)First aid chat in Tamil and English - 1no. (h)Battery water acidity tester - 1 no.

Preparation of site plan, physical layout, electrical line schematic diagram in 10 sets. Getting drawing approval from CEIG, preparation of completion report, rectification report and arranging CEIG’s inspection and obtaining safety certificate. Preparation of one set of approved drawing and a copy of safety certificate in a neat frame work to be fixed in the generator room – 1set.

Supply and laying of 31/2 x 120 sqmm size of PVC armoured LTUG cable in a trench tobe excavated at a depth of 0.75 Mtr. And puttin 0.15 mtr. layer of sand and covering the cable completely with concrete trough and sand and refilling the earth to make good. ( From Genset to AMF)

Supply and clamping of 31/2 x 120 sqmm of PVC armoured LTUG cable on post on wall with MS clamp.

Supply and fixing of brass cable gland for 3 1/2X 120 sq.mm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 1/2 x 95 sqmm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection

Supply and fixing of 400A changeover Switches with angle iron frame work with MS cable entry boxes with earth Connection

Supply of lubricating oil to run the Generator set for minimum of 8 hours by supply of 200 litres diesel

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Fixing of 16 KWP On Grid Solar PV Plant comprising of: (i)Solar panels of type Mono Crystline, PERC, etc., (ii)Power Conditioning Unit (PCU) with MPPT, Inverter, Controls, Protection Devices, Interconnecting D.C. cables, Connectors, Junction Boxes and accessories. (iii) D.C. D.B., (iv) A.C. D.B., (v) A.C. cables and accessories, (vi) Lightning arrestor, earthing, etc., (vii) Module Metallic Mounting Structures, viii) Installation, Testing and Commissioning corresponds to BIS and IEC requirements

BLUELEAF PROJECTS PRIVATE LIMITED (BID ID -1216567)

Sri Balaji Constructions (BID ID -1215823)

JAYAM ENGINEERING AND CONSTRUCTION (BID ID -1217076)