CA No CWE/FZR- /2020-21 Special repair to bldg No NP-56 of Garh Rif Bn under GE (East) Ferozepur Cantt

Amount

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegetation ,complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L for rendering 10 mm thick in cement mortar (1:4) on brick/concrete surfaces of roof, mixed with WPC (WPC shall be measured and paid seaparately), etc complete all as specified.

S&F 150 micron thick (transparent) polythene film with 150mm end & side laps, laid over a coat of bitumen primer @ 0.30 kg to 0.50 kg per sqm, bonded with a coat of 80/100 industrial bitumen @ 1.20 Kg/sqm and laid on roof, complete all as specified.

M&L 80 mm thick average, consolidated thickness, mud phuska on flat roofs,including 25 mm thick mud plaster and 3 mm thick leeping plaster, complete all as specified.

S&F 40 mm thick brick tiles laid over a layer of 25mm thick mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, complete all as specified.

All as per item No 6 herein before but using old brick tiles retrieved from dismantling (Item No 01 hereinbefore) including cleaning and removal of mortar from tiles, complete all as specified.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

Demolition of reinforced cement concrete in any position, complete all as specified.

M&L Cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in kerbs, mud stops, round or chamfered on edges etc including form work, weathering, slightly rounded or chamfered complete all as specified.

M&L Cement concrete (1:3:6) type C-1 (20 mm graded stone aggregate) as in filling of steel chowkhats and bed blocks of hold fast including necessary formwork complete all as specified.

M&L for Cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in 50mm thick plinth protection, surfaces finished even and fair without using extra cement complete all as directed by Engr-in-Charge and as specified.

M&L reinforced cement concrete (1:2:4) type A-1 (20 mm graded stone aggregate) as in slab supported on walls, beams, roofs, landing balconies, canopies, deck slabs and in shelves and like complete all as specified.

M&L for use & waste wooden form work (rough finished surfaces ) to sides & soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports overhangs, etc also splays between floors and beams, floor/roof slab, landings and similar work n. exc 200mm thick, complete all as specified

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius, complete all as specified.

All as per item 16 hereinbefore but using old bricks retrieved from demolition under item 15 hereinbefore including cleaning and removal of mortar from old bricks complete all as specified.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) complete all as specified.

M&L for (table dressed and pre-polished) black marble slab, 20 mm thick, as in cooking platforms, steps, jambs, pillars, window cills and like, set and bedded in grey cement slurry over & including 20 mm thick screed in cement mortar (1:4) and pointed in white cement (1:2) with admixture of pigment to match the shade of marble (mirror type polished) complete all as specified.

M&L for Glazed ceramic tiles, coloured ( colour & shade as approved), of size 300x200x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Non skid Ceramic coloured ( colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:4), complete all as specified.

S&F Mild steel TMT bars 10 mm dia cut to length, bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete ,FE-500/550 confirming to IS-1786-1985 all as specified & directed.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

All as per item No 26 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each and removing to stores, complete all as specified.

Dismantling of boarding, any description, fixed in any position with nails and screws, complete all as specified.

M & L for Prelaminated particle board, 18 mm thick, interior grade, prelaminated one side with decorative choice lamination approved shade & other side balancing white lamination, fixed in pelmets boxes, shelves, rebated or flat edges including 6 mm thich teak wood leaping all round and 20mm thick on hanging side, complete all as specified.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009),including making good jambs in CM(1:4) with finishes to match with existing, complete all as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site ,complete all as per specification in MES Schedule Part-I (2009) & drawing.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 125 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

M&L Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

M&L Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing, complete all as specified.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F Mild steel butt hinge, 100mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified.

S&F Mild steel barrel tower bolts, stove enameled black, with bright bolt, 200 mm long and fixed with steel screws, complete all as specified.

S&F Mild steel pressed handle, oval type, 125 mm long, stove enameled black and fixed with steel screws complete all as specified.

S&F 300 mm long aluminium anodized, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolts plate and two on staple plate, complete all as specified.

S&F in repair 300 mm mild steel helical door spring including roller and roller plate complete all as specified.

S&F Hasp and staple of aluminium anodized, safety type, 100 mm long, fixed with screws complete all as specified.

S&F continious piano hinges mild steel, bright finish or electrogalvanised width of flap 30mm, complete all a specified.

S&F PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified.

S&F PTMT handle,125 mm long and fixed with steel screws complete all as specified.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation, complete all as specified.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceiling, complete all as specified.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings,complete all as specified.

Re-fixing only, after cleaning old steel water tubing, 15mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors complete all as specified.

Re-fixing only, after cleaning old steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position including dismantling existing water storage tank on roofs, complete all as specified.

S&F in repair 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified.

S&F in repair 20 mm bore stop cock of cast copper alloy screwed down, high pressure with crutch or butterfly handle, complete all as specified.

S&F in repair 15mm stop valve cast copper alloy with crutch or butterfly handle ,screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated , complete all as specified.

S&F in repair 15 mm bore bib tap of, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repair 15mm bore pillar tap, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F 15mm stop valve cast copper alloy with crutch or butterfly handle ,screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy type shank and cup (concealed type), complete all as specified.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, complete all as specified.

S&F PVC connection 15mm size with brass nuts on both ends, 450mm long with PTMT nuts complete all as specified.

S&F Soap dish stainless steel of any type as directed, having thickness not less than 1mm, fixed to walls with chromium plated brass screws and wooden/plastic cleats, complete all as specified.

S&F in repairs Wash hand basin, flat back 550mm x400mm vitreous china (white) including PTMT waste coupling/fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing, complete all as specified.

S&F in repairs PVC syphonic action type low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, 32 mm PVC flush pipe and necessary fixing arrangements and connecting to water pipe ,complete all as specified .

S&F in repair, PTMT shower roses swivel type 125mm size (Minimum Wt 40 Grms) with or without joints, including fixing to steel pipe or union, complete all as specified.

S&F in repair Towel rail, 19mm dia of 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs, complete all as specified.

S&F in repair, stainless steel sinks 1mm thick kitchen or laboratory with plugs, washers, CP coupling and waste pipe including bedding in cement mortar fixed in RCC cooking platform including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm, complete all as specified.

Demolition and breaking up of 100 mm drain pipes (Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar, complete all as specified.

S&F, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and including stack clamps with nuts & bolts, complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scraping down smoke soot, mould, moss and efflorescent salts and trading oil, greasy spots and applying two coats of oil bound distemper, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered surfaces by brooming down with steel wire brush, scraping down smoke soot, mould, moss and efflorescent salts and trading oil, greasy spots and applying two coat of white wash on walls including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying two coat of white wash on ceiling including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint, complete all as specified.

M&L Preparation of old plastered surfaces of walls after complete removal of existing treatment and applying two coats of cement base paint complete all as specified.

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 20 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror type) complete all as specified.

S&F Kota stone slabs, 20 mm thick, machine cut as in shelf, skirting,steps,dado,pillars etc, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including rendering coat of 10 mm thick in cement mortar (1:4) including rubbing, cutting and polishing ,complete all as specified.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified.

M&L for Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified..

S&F Mild steel curtain rod PVC powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

S&F in repair rolled mild steel structural work i.e angle iron, flat etc as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work complete all as specified.

S&F in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified.

M&L Mild steel, plain black sheet of 0.80mm thickness in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc, complete all as specified.

S&F 60 mm thick (M-35 Grade) factory made, machine pressed,precast cement concrete interlocking paver block any shape with grey cement and no pigment, confirming to IS-15658:2006, set and joints grouted in fine sand, laid over and including 25 mm thick layer of sand cushioning complete all as specified and as directed.

Taking down carefully existing copper/alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire, ceiling fan etc and making good the disturbed surfaces of walls and ceilings, complete all as specified.

Taking down unserviceable main switches, electric metres and distribution boards single phase complete all as specified.

Taking down carefully old unserviceable sub main wiring and making good disturbed sufaces and matching with existing complete all as directed and specified.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia )duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following : - (a) One light/fan/bell/exhaust point controlled by one single pole one way switch.

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

All as per item 102 above, but one switch socket outlet multi purpose, 3pin, 15 Amps, point to be controlled by one switch and wiring with 2.5 Sqmm PVC FRLS cable,insulated, stranded, unsheathed copper conductor on Independent board with continuous earth wire of size 2.5 sqmm, PVC copper conductor, insulated, unsheathed, stranded, complete all as specified.

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked,complete all as specified.

S&F Switch, piano flush button type 15 Amps, single pole, one way,ISI marked, complete all as specified.

S&F Socket outlet,2 in 1, 5 pin ,5 Amp, piano flush type,ISI marked, complete all as specified.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type,ISI marked, complete all as specified.

S&F bell push Switch, 6 Amps,1 module,ISI marked, complete all as specified.

S&F bell Ding Dong AC 230 volts, single pole, complete all as specified.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals complete all as specified.

S&F Lamp holder, insulated body, threaded dome pattern, suitable for bracket/batten fittings including LED bulb of 10 watts, complete all as specified.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size,230 volts,6 Amps, complete all as specified.

S&F in repair of regular batten for LED 18W indoor decorative batten with extruded aluminium housing & Opal diffuser IP-20 fixed to walls/ ceiling etc complete including LED tube 18 W all as specified.

S&F in repairs bldg security light LED fittings 25 watts new generation energy saving environmental friendly long life highly efficient toughened glass with frame, complete with all accessories like lamp, bracket of not exc 1.2 metre 40 mm GI light grade tubing & bent at middle to shape by 120 degree from vertical du;ly painted with two coats of aluminium paint with mild steel clamps, nuts & bolts,sleek pressure die cast aluminium housing heat resistant glass IP-66 protection, cable insulated and PVC sheathed copper conductor multi stranded and connecting to conductor and testing, complete all as specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, VTPN DB with 200 Amps rated bus bar, 4 way, FP-42 protection surface mounting, 415 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made,including thermal based release adjustable type 4 pole, 63 Amps, 50 Hz, 415 volts with rupturing capacity 16 KA and making good disturbed surfaces with matching colour, complete all as specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly cocealled in wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F in repairs MCB, SPN, 63 Amps, 240 volts 10 KA, complete all as specified.

S&F in repairs MCB, single pole, 240 Volt, 5 to 32 Amps, 10 KA complete all as specified.

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x6 Sqmm single core 650/1100 V , drawn through & including rigid PVC non metallic concealed conduit 25 mm dia including continuous earth wire of size 1x6 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour) complete all as specified.NOTE:-Two rurns of cable ,1 run of earth wire & one run of PVC conduit shall be measured as one length.

S&F exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 RPM, Single Phase with bolts,nuts and washers size of bolt 15cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to Exhaust fan max 1.5 mtr for giving connection, complete all as specified.

Cutting hole of suitable size making good, the disturbed surface, grouting nuts & bolts for fixing of exhaust fans, complete all as specified.

M&L for disconnecting electric meter of any capacity and refixing the same after rewiring, in meter box including connection complete all as specified.

S&F sheet metel Meter box, single door minimum size 30cm x 45cm x 20cm for electric meter factory made of MS sheets/CRCA sheet duly painted with powder paint and door hinged locking arrangement confirming IS 5039 of 1983. The electric meter/switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. Before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. Concealed in wall, including making good disturbed surfaces with matching colour, complete all as specified.

Fixing or hanging only ceiling fan height 3 metres to 5 metres of bldg including three core FR PVC insulated & overall round sheathed flexible with PVC, colour of cores are Red, Black & Yellow/Green is from earthing sheath colour is Black of cable size 23/0.0076, complete all as specified. Note: ceiling fan obtained from taking down in item Sr No 99 above.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire, complete all as specified.

M& L Earthing as in repairs complete, all as shown on electrical plate No 3 of MES schedule part-I , as in repairs and as specified including the following :-(i) Galvanised steel earth plate of size 60cmsx60cmsx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level. (ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer). (iii) 4 mm dia (8 SWG) G.I earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc. (iv) 15 mm bore light grade, GI pipe for protection to earth-strip. (v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) 50mm thick pre-cast cover of cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate and MS angle iron 25x25x3mm frame including two coats of painting over a coat of red oxide primer to exposed steel surfaces. (vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre as directed.

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan,for laying of cable and getting out,compete all as specified.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. (Excavation and earth work measured separately).Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified. (Excavation and earth work measured separately.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified.

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified.

S.R. Kaura and Company

M/S Yashpaul Gulati

M/s Bansi Lal

M/S CHAWLA CONSTRUCTION COMPANY

M/S Sandhu Const.Co.

ABHISHEK AND COMPANY

Marwaha Builders